Wolfgang Denk [Wed, 5 Oct 2011 09:55:01 +0000 (09:55 +0000)]
TQM8xx: make room for growing code size due to I/O accessor cleanup
Commit "PPC: Cleanup tqm8xx_pcmcia.c" will clean up the PCMCIA code
to use I/O accessors instead of plain volatile pointer accesses.
This will result in about 300 byte bigger code. Fix custom linker
script to make room for this.
While we are at it, drop unmaintained u-boot.lds.debug linker script.
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Tested-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Tue, 4 Oct 2011 20:20:25 +0000 (22:20 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-nand-flash
* 'master' of git://git.denx.de/u-boot-nand-flash:
PPC: Fix socrates NAND problem
PPC: Fix fsl_upm.c by renaming nand handling functions
NAND: Make page, erase, oob size available via cmd_nand
mtd: eLBC NAND: remove elbc_fcm_ctrl->oob_poi
NAND: Add -y option to nand scrub command
NAND: Add nand read.raw and write.raw commands
NAND: Really ignore bad blocks when scrubbing
spl, nand: add 4bit HW ecc oob first nand_read_page function
mxc_nand: fix a problem writing more than 32MB
mxc_nand: fixed some typos (cosmetic)
nand: increase chip_delay in mv kirkwood nand driver
Wolfgang Denk [Tue, 4 Oct 2011 20:08:13 +0000 (22:08 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/p3060: Add SoC related support for P3060 platform
powerpc/85xx: Add support for setting up RAID engine liodns on P5020
powerpc/85xx: Refactor some defines out of corenet_ds.h
fm-eth: Add ability for board code to disable a port
powerpc/mpc8548: Add workaround for erratum NMG_LBC103
powerpc/mpc8548: Add workaround for erratum NMG_DDR120
powerpc/mpc85xxcds: Fix PCI speed
powerpc/mpc8548cds: Fix booting message
powerpc/p4080: Add support for secure boot flow
powerpc/85xx: Add Secure Boot support on P1010RDB for NOR, NAND & SPIFLASH
powerpc/85xx: Add PBL & SECUREBOOT support on P3041/P5020DS boards
powerpc/p2041rdb: remove watch dog related codes
powerpc/p2041rdb: updated description of cpld command
powerpc/p2041rdb: add more ddr frequencies support
powerpc/p2041rdb: set sysclk according to status of physical switch SW1
powerpc/p2041rdb: update cpld reset command according to CPLD 2.0
powerpc/mpc8349emds: Migrate from spd_sdram to unified DDR driver
powerpc/mpc83xx: Migrate from spd_sdram to unified DDR driver
powerpc/mpc8xxx: Add DDR2 to unified DDR driver
powerpc/mpc8xxx: Fix picos_to_mclk() and get_memory_clk_period_ps()
powerpc/mpc8xxx: Add SPD EEPROM address for single controller 2 slots
powerpc/mpc8xxx: Fix DDR code for empty first DIMM slot and enable DQS_en
powerpc/85xx: Refactor P2041RDB to use common p_corenet files
powerpc/85xx: refactor common P-Series CoreNet files for FSL boards
powerpc/85xx: Enable CMD_REGINFO on corenet boards
powerpc/85xx: p2041rdb - Remove unused 'execute' perm in TLB entries
powerpc/85xx: Fix USB protocol definitions for P1020RDB
powerpc/corenet_ds: Use separated speed tables for UDIMM and RDIMM
powerpc/mpc8xxx: Move DDR RCW overriding to common code
powerpc/mpc8xxx: Extend CWL table
powerpc/85xx: Cleanup how SVR_MAJ() is defined on MPC8536
powerpc/85xx: Cleanup extern in corenet_ds board code
powerpc/p2041rdb: Add ethernet support on P2041RDB board
powerpc/85xx: Add networking support to P1023RDS
powerpc/hydra: Add ethernet support on P5020/P3041 DS boards
powerpc/85xx: Add FMan ethernet support to P4080DS
powerpc/85xx: Add support for FMan ethernet in Independent mode
powerpc/mpc8548cds: Cleanup mpc8548cds.c
powerpc/mp: add support for discontiguous cores
powerpc/85xx: corenet_ds - Remove unused 'execute' perm in TLB entries
fdt: Add new fdt_create_phandle helper
fdt: Rename fdt_create_phandle to fdt_set_phandle
powerpc/85xx: Fix compile warnings/errors if CONFIG_SYS_DPAA_FMAN isn't set
fsl_ifc: Add the workaround for erratum IFC A-003399(enabled on P1010)
powerpc/P1010: Add workaround for erratum P1010-A003549 (related to IFC)
fsl_ifc: Add the workaround for erratum IFC-A002769 (enable on P1010)
powerpc/85xx: Expanding the window of CCSRBAR in AS=1 from 4k to 1M
powerpc/85xx: Add NAND/NAND_SPL support to P1010RDB
nand: Freescale Integrated Flash Controller NAND support
powerpc/85xx: Add basic support for P1010RDB
powerpc/85xx: Add support for new P102x/P2020 RDB style boards
powerpc/85xx: relocate CCSR before creating the initial RAM area
powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros
powerpc/85xx: Enable internal USB UTMI PHY on p204x/p3041/p50x0
powerpc/85xx: Add ULPI and UTMI USB Phy support for P1010/P1014
Wolfgang Denk [Tue, 4 Oct 2011 20:05:15 +0000 (22:05 +0200)]
Merge branch 'emaclite' of git://git.denx.de/u-boot-microblaze
* 'emaclite' of git://git.denx.de/u-boot-microblaze:
net: emaclite: Use dynamic allocation
net: emaclite: Remove baseaddress from xemaclite
net: emaclite: Use calloc instead of malloc
net: emaclite: Remove deviceid property
net: emaclite: Change driver name and add address
Wolfgang Denk [Tue, 4 Oct 2011 19:32:16 +0000 (21:32 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-microblaze
* 'master' of git://git.denx.de/u-boot-microblaze:
microblaze: Enable FDT/FIT support
microblaze: Remove address offset for uart16550
microblaze: Do not select NFS for platforms without ethernet
microblaze: Clean up reset asm code
microblaze: Save and restore first unused vector
microblaze: Setup MB vectors if feature is enable for u-boot
microblaze: Remove debug saving value
The commit causes build breakage for a number of boards. This results
from the fact that now the arguments of debug() actually get
referenced (even if there is hope that the compiler will optimize
away the debug() call). The obvious fix to that probem (change the
code to always declare the referenced variables and data structures)
increases the code size, and was this rejected. So it was decided to
revert this commit until a better solution is found.
Marek Vasut [Mon, 3 Oct 2011 22:56:09 +0000 (00:56 +0200)]
PPC: Fix socrates NAND problem
nand.c:36: error: static declaration of 'nand_read_buf' follows non-static declaration
/home/marex/u-boot/include/nand.h:139: error: previous declaration of 'nand_read_buf' was here
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
The eLBC NAND driver currently follows up each program/write operation with a
read-back of the page, in order to [ostensibly] fill in ECC data for the
caller. However, the page address used for this read is always -1, so the read
will never work correctly. Remove this useless (and potentially problematic)
block of code.
v2: fix broken mailer
Signed-off-by: mhench <mhench@elutions.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Marek Vasut [Tue, 13 Sep 2011 22:20:35 +0000 (00:20 +0200)]
NAND: Add -y option to nand scrub command
This allows the scrub command to scrub without asking the user if he really
wants to scrub the area. Useful in scripts.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de> Acked-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Scott Wood <scottwood@freescale.com>
Marek Vasut [Fri, 23 Sep 2011 13:43:10 +0000 (15:43 +0200)]
NAND: Add nand read.raw and write.raw commands
These commands should work around various "hardware" ECC and BCH methods.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
[scottwood@freescale.com: s/write the page/access the page/] Signed-off-by: Scott Wood <scottwood@freescale.com>
Marek Vasut [Mon, 12 Sep 2011 04:04:06 +0000 (06:04 +0200)]
NAND: Really ignore bad blocks when scrubbing
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
[scottwood@freescale.com: use chip instead of redundant priv_nand] Signed-off-by: Scott Wood <scottwood@freescale.com>
Helmut Raiger [Wed, 6 Jul 2011 17:04:41 +0000 (19:04 +0200)]
mxc_nand: fix a problem writing more than 32MB
When writing 0x4000 to the unlockend_blkaddr register, large writes to
a 2k page NAND sometimes fail. The current kernel driver writes 0xFFFF
to this register for V2 of the nand controller.
However on an i.MX31 this also fixes writes larger than 32MB.
The datasheet is very unspecific, but (0x4000=16384)*2000
roughly fits the limits we're encountering with NAND writes.
This problem might be NAND chip specific.
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at> Signed-off-by: Scott Wood <scottwood@freescale.com>
Stefan Bigler [Mon, 18 Jul 2011 13:25:11 +0000 (15:25 +0200)]
nand: increase chip_delay in mv kirkwood nand driver
The new SAMSUNG NAND Flash K9F1G08U0D require a bigger chip_delay.
The Data Transfer from Cell to Register is >= 35us. Other Vendors
and older chips normally use >= 25us. To have enough margin 40us
is selected.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Stefan Roese <sr@denx.de> Signed-off-by: Scott Wood <scottwood@freescale.com>
Shengzhou Liu [Wed, 31 Aug 2011 09:48:18 +0000 (17:48 +0800)]
powerpc/p3060: Add SoC related support for P3060 platform
Add P3060 SoC specific information:cores setup, LIODN setup, etc
The P3060 SoC combines six e500mc Power Architecture processor cores with
high-performance datapath acceleration architecture(DPAA), CoreNet fabric
infrastructure, as well as network and peripheral interfaces.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Sat, 10 Sep 2011 15:44:13 +0000 (10:44 -0500)]
powerpc/85xx: Add support for setting up RAID engine liodns on P5020
Add support for Job Queue/Ring LIODN for the RAID Engine on P5020. Each
Job Queue/Ring combo needs one id assigned for a total of 4 (2 JQs/2
Rings per JQ). This just handles RAID Engine in non-DPAA mode.
Signed-off-by: Santosh Shukla <santosh.shukla@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 31 Aug 2011 14:50:13 +0000 (09:50 -0500)]
powerpc/85xx: Refactor some defines out of corenet_ds.h
Move some SoC/board specific defines out of corenet_ds.h and into the
corresponding P3041DS/P4080DS/P5020.h.
We moved CONFIG_MMC, CONFIG_PCIE3, & CONFIG_FSL_NGPIXIS because the P3060
SoC/reference board does not have these devices and it will share the same
board code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 14 Sep 2011 17:01:35 +0000 (12:01 -0500)]
fm-eth: Add ability for board code to disable a port
The SoC configuration may have more ports enabled than a given board
actually can utilize. Add a routinue that allows the board code to
disable a port that it knows isn't being used.
fm_disable_port() needs to be called before cpu_eth_init().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Mon, 3 Oct 2011 13:37:57 +0000 (08:37 -0500)]
powerpc/mpc8548: Add workaround for erratum NMG_LBC103
The erratum NMG_LBC103 is LBIU3 in MPC8548 errata document.
Any local bus transaction may fail during LBIU resynchronization
process when the clock divider [CLKDIV] is changing. Ensure there
is no transaction on the local bus for at least 100 microseconds
after changing clock divider LCRR[CLKDIV].
Refer to the erratum LBIU3 of mpc8548.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 16 Sep 2011 14:54:30 +0000 (09:54 -0500)]
powerpc/mpc8548: Add workaround for erratum NMG_DDR120
Erratum NMG_DDR120 (DDR19 in MPC8548 errata document) applies to some
early version silicons. The default settings of the DDR IO receiver
biasing may not work at cold temperature. When a failure occurs,
a DDR input latches an incorrect value. The workaround will set the
receiver to an acceptable bias point.
Signed-off-by: Gong Chen Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Ruchika Gupta [Wed, 15 Dec 2010 17:02:08 +0000 (17:02 +0000)]
powerpc/p4080: Add support for secure boot flow
Pre u-boot Flow:
1. User loads the u-boot image in flash
2. PBL/Configuration word is used to create LAW for Flash at 0xc0000000
(Please note that ISBC expects all these addresses, images to be
validated, entry point etc within 0 - 3.5G range)
3. ISBC validates the u-boot image, and passes control to u-boot
at 0xcffffffc.
Changes in u-boot:
1. Temporarily map CONFIG_SYS_MONITOR_BASE to the 1M
CONFIG_SYS_PBI_FLASH_WINDOW in AS=1.
(The CONFIG_SYS_PBI_FLASH_WINDOW is the address map for the flash
created by PBL/configuration word within 0 - 3.5G memory range. The
u-boot image at this address has been validated by ISBC code)
2. Remove TLB entries for 0 - 3.5G created by ISBC code
3. Remove the LAW entry for the CONFIG_SYS_PBI_FLASH_WINDOW created by
PBL/configuration word after switch to AS = 1
CPLD 2.2 removed board watch dog support due to the limitation of CPLD
capacity after adding all the requested features, such as switch overriding.
There is no pin-compatible upgrade part available for current PCB design.
So remove codes related to it.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
powerpc/p2041rdb: add more ddr frequencies support
This table covers DDR frequencies from 666 to 1666. Frequencies 666, 833,
1000, 1066 and 1333 were verified on this board with SO-DIMM
(UG51U6400N8SU-ACF).
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
powerpc/p2041rdb: update cpld reset command according to CPLD 2.0
CPLD 2.0 provides a new register which bit[0] is set to '1' will reset
board with initializing the CPLD registers to default values. And add
bit[6] of register at offset 0x5 to use to enable flash bank selection.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Lei Wen [Fri, 30 Sep 2011 05:43:48 +0000 (05:43 +0000)]
I2C: mv_i2c: fix build issue when enable debug option
When DEBUG_I2C is open, the following build issue would shows up.
mv_i2c.c: In function 'i2c_transfer':
mv_i2c.c:257: error: 'ISR' undeclared (first use in this function)
mv_i2c.c:257: error: (Each undeclared identifier is reported only once
mv_i2c.c:257: error: for each function it appears in.)
Michal Simek [Thu, 25 Aug 2011 10:25:14 +0000 (12:25 +0200)]
net: emaclite: Change driver name and add address
Current xilinx emaclite use net multi registration
but doesn't support several emaclites interfaces.
Changing driver name with adding address to name
is the first step how to distiguish several drivers.
Michal Simek [Mon, 15 Nov 2010 09:54:43 +0000 (09:54 +0000)]
microblaze: Save and restore first unused vector
Use one memory space to detect little/big endian platforms.
The first unused address(0x28) is used instead 0x0 address (reset vectors).
Detection rewrited reset vector setup from first stage bootloader.
Workflow:
1. Store 0x28 to r7
2. Do little/big endian test
3. Restore r7 to 0x28
Marek Vasut [Fri, 30 Sep 2011 10:13:23 +0000 (12:13 +0200)]
GCC4,6: Squash warning in cmd_nand.c
cmd_nand.c: In function ‘do_nand’:
cmd_nand.c:490:7: warning: variable ‘chip’ set but not used
[-Wunused-but-set-variable]
cmd_nand.c:489:7: warning: variable ‘part’ set but not used
[-Wunused-but-set-variable]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Scott Wood <scottwood@freescale.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
Marek Vasut [Mon, 26 Sep 2011 00:26:05 +0000 (02:26 +0200)]
GCC4.6: Squash warnings in ipu_disp.c
ipu_disp.c: In function ‘ipu_disp_set_global_alpha’:
ipu_disp.c:1237:11: warning: variable ‘flow’ set but not used
[-Wunused-but-set-variable]
ipu_disp.c: In function ‘ipu_disp_set_color_key’:
ipu_disp.c:1302:16: warning: variable ‘flow’ set but not used
[-Wunused-but-set-variable]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Mon, 26 Sep 2011 00:26:04 +0000 (02:26 +0200)]
GCC4.6: Squash warnings in lcd.c
lcd.c: In function ‘lcd_drawchars’:
lcd.c:214:9: warning: variable ‘off’ set but not used
[-Wunused-but-set-variable]
lcd.c: In function ‘lcd_display_bitmap’:
lcd.c:617:16: warning: variable ‘compression’ set but not used
[-Wunused-but-set-variable]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Marek Vasut [Mon, 26 Sep 2011 17:36:19 +0000 (19:36 +0200)]
GCC4.6: Convert various empty macros to inline functions
Fix the following gcc4.6 problems:
cmd_date.c: In function ‘do_date’:
cmd_date.c:50:6: warning: variable ‘old_bus’ set but not used
[-Wunused-but-set-variable]
asix.c: In function ‘asix_init’:
asix.c:317:6: warning: variable ‘rx_ctl’ set but not used
[-Wunused-but-set-variable]
usb.c: In function ‘usb_parse_config’:
usb.c:331:17: warning: variable ‘ch’ set but not used
[-Wunused-but-set-variable]
usb.c: In function ‘usb_hub_port_connect_change’:
usb.c:1123:29: warning: variable ‘portchange’ set but not used
[-Wunused-but-set-variable]
usb.c: In function ‘usb_hub_configure’:
usb.c:1183:25: warning: variable ‘hubsts’ set but not used
[-Wunused-but-set-variable]
usb_storage.c: In function ‘usb_stor_CB_reset’:
usb_storage.c:466:6: warning: variable ‘result’ set but not used
[-Wunused-but-set-variable]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Paul Gortmaker [Sat, 17 Sep 2011 13:47:47 +0000 (13:47 +0000)]
sbc82xx: delete support for obsolete SBC8240/SBC8260
The EST SBC8260 is over 10 years old, and the SBC8240 older than
that. With the tiny amount of RAM (by today's standards), there
really isn't anyone interested in running the latest U-boot on
these EOL products anymore.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> CC: jon.diekema@smiths-aerospace.com
Graeme Russ [Mon, 29 Aug 2011 02:14:05 +0000 (02:14 +0000)]
console: Squelch pre-console output in console functions
There are some locations in the code which anticipate printf() being called
before the console is ready by squelching printf() on gd->have_console.
Move this squelching into printf(), vprintf(), puts() and putc(). Also
make tstc() and getc() return 0 if console is not yet initialised
Signed-off-by: Graeme Russ <graeme.russ@gmail.com> Tested-by: Simon Glass <sjg@chromium.org>
Sergei Shtylyov [Fri, 19 Aug 2011 09:37:46 +0000 (09:37 +0000)]
fat: replace LINEAR_PREFETCH_SIZE with PREFETCH_BLOCKS
Currently in do_fat_read() when reading FAT sectors, we have to divide down
LINEAR_PREFETCH_SIZE by the sector size, whereas it's defined as 2 sectors
worth of bytes. In order to avoid redundant multiplication/division, introduce
#define PREFETCH_BLOCKS instead of #define LINEAR_PREFETCH_SIZE.
Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
Sergei Shtylyov [Fri, 19 Aug 2011 09:32:34 +0000 (09:32 +0000)]
fat: root directory cluster only makes sense for FAT32
The root directory cluster field only exists in a FAT32 boot sector, so the
'root_cluster' variable in do_fat_read() contains garbage in case of FAT12/16.
Make it contain 0 instead as this is what is passed to get_vfatname() in that
case anyway.
Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
Sergei Shtylyov [Mon, 8 Aug 2011 09:39:29 +0000 (09:39 +0000)]
fat: cannot compare bytes and sectors
The code multiples the FAT size in sectors by the sector size and then tries to
compare that to the number of sectors in the 'getsize' variable. While fixing
this, also change the initial value of 'getsize' as the division of FATBUFSIZE
by the sector size gets us FATBUFBLOCKS.
Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
Sergei Shtylyov [Mon, 8 Aug 2011 09:38:33 +0000 (09:38 +0000)]
fat: fix crash with big sector size
Apple iPod nanos have sector sizes of 2 or 4 KiB, which crashes U-Boot when it
tries to read the boot sector into 512-byte buffer situated on stack. Make the
FAT code indifferent to the sector size.
Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
Wolfgang Denk [Sat, 1 Oct 2011 19:42:21 +0000 (21:42 +0200)]
Merge branch 'post' of git://git.denx.de/u-boot-blackfin
* 'post' of git://git.denx.de/u-boot-blackfin:
Blackfin: uart: implement loop callback for post
Blackfin: bf537-stamp/bf548-ezkit: update POST flash block range
Blackfin: post: generalize led/button tests with GPIOs
Blackfin: bf537-stamp: drop uart/flash post tests
Blackfin: post: drop custom test list
Blackfin: bf537-stamp: convert to gpio post hotkey
Marek Vasut [Thu, 22 Sep 2011 09:22:12 +0000 (09:22 +0000)]
I2C: mxc_i2c rework
Rewrite the mxc_i2c driver.
* This version is much closer to Linux implementation.
* Fixes IPG_PERCLK being incorrectly used as clock source
* Fixes behaviour of the driver on iMX51
* Clean up coding style a bit ;-)
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Jason Hui <jason.hui@linaro.org> Acked-by: Jason Liu <jason.hui@linro.org> Acked-by: Heiko Schocher <hs@denx.de> Tested-by: Jason Liu <jason.hui@linro.org>
Marek Vasut [Thu, 22 Sep 2011 09:20:37 +0000 (09:20 +0000)]
MX5: Add AHB clock reporting and fix IPG clock reporting
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Jason Liu <jason.hui@linaro.org> Acked-by: Jason Liu <jason.hui@linaro.org>
Marek Vasut [Fri, 23 Sep 2011 09:43:47 +0000 (11:43 +0200)]
MX5: Modify the PLL decoding algorithm
The PLL decoding algorithm didn't take into account many configuration bits.
Adjust it according to Linux kernel. Also, add PLL4 for MX53.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Jason Hui <jason.hui@linaro.org> Tested-by: Jason Liu <Jason.hui@linaro.org>
projects / u-boot / log