Update qbman driver
- As per latest available qbman driver
- Use of atomic APIs
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> CC: Geoff Thorpe <Geoff.Thorpe@freescale.com> CC: Haiying Wang <Haiying.Wang@freescale.com> CC: Roy Pledge <Roy.Pledge@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Update flibs changes to mc-0.6.0.1 for dpmang, dprc, dpni and dpio objects
Also rename qbman_portal_ce/ci_paddr to qbman_portal_ce/ci_offset in
dpio_attr. These are now offsets from the SoC QBMan portals base.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
drivers/fsl-mc: Autoload AOIP image from NOR flash
Load AIOP image from NOR flash into DDR so that the MC firmware
the MC fw can start it at boot time
Signed-off-by: J. German Rivera <German.Rivera@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
drivers/fsl-mc: Make MC boot error messages more readable
Make it easier for the user to notice when the MC firmware
had problems booting.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Stuart Yoder [Thu, 28 May 2015 09:24:15 +0000 (14:54 +0530)]
armv8/ls2085a: enable debug server
Signed-off-by: Stuart Yoder <stuart.yoder at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
armv8/fsl-lsch3: Support 256M mem split for MC & dbg-srvr
The agreed split of the top of memory is 256M for debug server and 256M
for MC. This patch implements the split.
In addition, the MC mem must be 512MB aligned, so the amount of memory
to hide must be 512MB to achieve that alignment.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Bhupesh Sharma [Thu, 28 May 2015 09:24:13 +0000 (14:54 +0530)]
arm/errata: Update required bits for A57 cores erratas
This patch updates the setting of required bits for A57 cores erratas
- 828024 and 826974
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com> Signed-off-by: Dai Haruki <dai.haruki at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Bhupesh Sharma [Thu, 28 May 2015 09:24:12 +0000 (14:54 +0530)]
driver/fsl_debug_server: Fix the DDR hide logic for LS2085a
This patch fixes the DDR hide logic for LS2085a, correcting the way
the Debug Server FW and MC FW images are placed on the top of system
DDR and how the rest of the system DDR space is made visibile to Linux.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Update SoC README to provide details of
- Memory regions
- Memory used by MC and Debug server
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Bhupesh Sharma [Thu, 28 May 2015 09:24:10 +0000 (14:54 +0530)]
armv8/ls2085a: Expose all DDR region(s) to Linux
This patch allows u-boot to expose the complete DDR region(s) to Linux
(after subtracting the memory hidden via MEM_TOP_HIDE mechanism).
This allows the u-boot to support the 48-bit VA support provided by
ARM64 Linux in flavors 3.18 and above, by passing the appropriate
'memory' DTS nodes.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
York Sun [Thu, 28 May 2015 09:24:09 +0000 (14:54 +0530)]
armv8/ls2085ardb: Fix SPD address error on early boards
Board rev C and earlier has duplicated SPD address on 2nd DDR
controller slots. It is fixed on rev D and later. SPD addresses
need to be updated accordingly.
Signed-off-by: York Sun <yorksun at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
armv8/fsl-ch3: Add support to print SoC personality
This patch adds support to print out the SoC personality.
Freescale LS20xx SoCs (compliant to Chassis-3 specifications) can
have 6 personalities: LS2045AE, LS2045A, LS2080AE, LS2080A,
LS2085AE and LS2085A
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Jaiprakash Singh [Thu, 28 May 2015 09:24:03 +0000 (14:54 +0530)]
board/fsl/common: Fix eeprom system version endianness
SYSTEM ID EPPROM always store SYSTEM version info in big endian format.
SoC with ARM or PowerPC core should read/write version info from eeprom
in BIG endian format.
So use cpu-specific APIs to read SYSTEM version.
Signed-off-by: Jaiprakash Singh <b44839 at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Bhupesh Sharma [Thu, 28 May 2015 09:24:02 +0000 (14:54 +0530)]
armv8/ls2085a: Increase the supported kernel size
Increases the kernel size supported for LS2085A platforms:-
- Update environment variables
- Add ramdisk_size in bootargs env variable
- Define CONFIG_SYS_BOOTM_LEN to 64MB
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
armv8/ls2085qds: Update SFP TX bit as "0" to enable XFI
FPGA BRDCFG9[SFP_TX] should be clear in order to enable XFI ports.
Signed-off-by: Dai Haruki <Dai.Haruki at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
armv8/ls2085a: call ft_pcie_setup() to change dts status
call ft_pci_setup() to disable PCIe dts node if corresponding
PCIe controller is disabled according to RCW
Signed-off-by: Minghuan Lian <Minghuan.Lian at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Compatible field "fsl,20851a-pcie" is not correct.
So update it to "fsl,ls2085a-pcie"
Signed-off-by: Minghuan Lian <Minghuan.Lian at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Priyanka Jain [Thu, 28 May 2015 09:23:56 +0000 (14:53 +0530)]
armv8/ls2085a: Enable "date" command for QDS and RDB
Enable "date" command for QDS and RDB boards
Signed-off-by: Priyanka Jain <Priyanka.Jain at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Yangbo Lu [Thu, 28 May 2015 09:23:55 +0000 (14:53 +0530)]
armv8/ls2085ardb: add hwconfig setting for eSDHC
Add hwconfig setting for eSDHC since it shares some pins with other
IP block.
Signed-off-by: Yangbo Lu <yangbo.lu at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
armv8/ls2085ardb: Add eth & phy firmware loading support
Add support for board eth initialization and support for loading phy
firmware. PHY firmware needs to be loaded from board_eth_init() because
all the MACs are not initialized by ldpaa_eth driver.
Signed-off-by: pankaj chauhan <pankaj.chauhan at freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
Bin Meng [Wed, 8 Jul 2015 05:06:41 +0000 (13:06 +0800)]
pci: Disable expansion ROM address decoding when signature check fails
We should not leave the expansion ROM address window open when there
is not a valid ROM.
Suggested-by: Matt Porter <mporter@konsulko.com> Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Wed, 8 Jul 2015 05:06:40 +0000 (13:06 +0800)]
pci: Configure expansion ROM during auto config process
Currently PCI expansion ROM address is assigned by a call to
pciauto_setup_rom() outside of the pci auto config process.
This does not work when expansion ROM is on a device behind
PCI bridge where bridge's memory limit register was already
programmed to a value that does not cover the newly assigned
expansion ROM address. To fix this, we should configure the
ROM address during the auto config process.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Sat, 16 May 2015 01:33:16 +0000 (09:33 +0800)]
drivers: block: Remove the ata_piix driver
This driver was originally added to support the native IDE mode for
Intel chipset, however it has some bugs like not supporting ATAPI
devices, endianness issue, or even broken build when CONFIG_LAB48.
Given no board is using this driver as of today, rather than fixing
all these issues we just remove it from the source tree.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Mon, 6 Jul 2015 07:57:06 +0000 (15:57 +0800)]
tools: ifdtool: Write correct offset on 32-bit machine
On 32-bit machine strtol() returns LONG_MAX which is 0x7fffffff,
which is wrong for u-boot.rom components like u-boot-x86-16bit.bin.
Change to use strtoll() so that it works on both 32-bit and 64-bit
machines.
Reported-by: Fei Wang <wangfei.jimei@gmail.com> Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 4 Jul 2015 00:28:28 +0000 (18:28 -0600)]
x86: Add binary blob checksums for Minnowboard MAX
To try to reduce the pain of confusion of binary blobs, add MD5 checksums
for the current versions. This may worsen the situation as new versions
appear, but it should still be possible to obtain these versions, and thus
get a working setup.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 4 Jul 2015 00:28:26 +0000 (18:28 -0600)]
dm: x86: minnowmax: Move PCI to use driver model
Adjust minnowmax to use driver model for PCI. This requires adding a device
tree node to specify the ranges, removing the board-specific PCI code and
ensuring that the host bridge is configured.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Simon Glass <sjg@chromium.org>
Bin Meng [Mon, 6 Jul 2015 08:31:35 +0000 (16:31 +0800)]
x86: crownbay: Enable graphics support
Enable graphics support on Intel Crown Bay board With the help of
vgabios for Intel TunnelCreek IGD. Tested with an external LVDS
panel connected to X4 connector and SDVO adapter connected to X9
connector on the board.
Signed-off-by: Jian Luo <jian.luo4@boschrexroth.de> Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Mon, 6 Jul 2015 08:31:33 +0000 (16:31 +0800)]
x86: Move VGA option rom macros to Kconfig
Move X86_OPTION_ROM_FILE & X86_OPTION_ROM_ADDR to arch/x86/Kconfig
and rename them to VGA_BIOS_FILE & VGA_BIOS_ADDR which depend on
HAVE_VGA_BIOS. The new names are consistent with other x86 binary
blob options like HAVE_FSP/FSP_FILE/FSP_ADDR.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Mon, 6 Jul 2015 08:31:31 +0000 (16:31 +0800)]
x86: queensbay: Change CPU_ADDR_BITS to 32
Per CPUID:80000008h result, the maximum physical address bits of
TunnelCreek processor is 32 instead of default 36. This will fix
the incorrect decoding of MTRR range mask.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Mon, 6 Jul 2015 08:31:30 +0000 (16:31 +0800)]
x86: Setup fixed range MTRRs for legacy regions
We should setup fixed range MTRRs for some legacy regions like VGA
RAM and PCI ROM areas as uncacheable. Note FSP may setup these to
other cache settings, but we can override this in x86_cpu_init_f().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Jian Luo [Mon, 6 Jul 2015 08:31:29 +0000 (16:31 +0800)]
video: Add 32-bit color depth support for VBE
The TunnelCreek IGD VBE reports 32-bit color depth regardless 24-bit
color depth is configured. Since 24-bit mode already uses 4 bytes
internally, it should be OK to just add this option in switch case.
Signed-off-by: Jian Luo <jian.luo4@boschrexroth.de> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Bin Meng <bmeng.cn@gmail.com>
Bin Meng [Mon, 6 Jul 2015 08:31:26 +0000 (16:31 +0800)]
video: vesa_fb: Look up VGA device by class instead of id
Per PCI spec, VGA device reports its class as standard 030000h in
its configuration space, so we can use it to determine if we need
run option rom instead of testing the supported vendor/device ids.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 7 Jun 2015 14:50:40 +0000 (08:50 -0600)]
dm: pci: Use the correct hose when configuring devices
Only the PCI controller has access to the PCI region information. Make sure
to use the controller (rather than any attached bridges) when configuring
devices.
This corrects a failure to scan and configure devices when driver model is
enabled for PCI.
So far interrupt routing works pretty well for any on-chip devices
on Intel Crown Bay. When inserting any PCIe card to any PCIe slot,
Linux kernel is smart enough to do interrupt swizzling and figure
out device's irq using its parent bridge's interrupt routing info
all the way up to its root port. In U-Boot all PCIe root ports'
interrupts were routed to PIRQ E/F/G/H before, while actually all
PCIe downstream ports received INTx are routed to PIRQ A/B/C/D
directly and not configurable. Now we change this mapping so that
any external PCIe device can work correctly.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Tue, 23 Jun 2015 04:18:52 +0000 (12:18 +0800)]
x86: Generate a valid MultiProcessor (MP) table
Implement write_mp_table() to create a minimal working MP table.
This includes an MP floating table, a configuration table header
and all of the 5 base configuration table entries. The I/O interrupt
assignment table entry is created based on the same information used
in the creation of PIRQ routing table from device tree. A check
duplicated entry logic is applied to prevent writing multiple I/O
interrupt entries with the same information.
Use a Kconfig option GENERATE_MP_TABLE to tell U-Boot whether we
need actually write the MP table at the F seg, just like we did for
PIRQ routing and SFI tables. With MP table existence, linux kernel
will switch to I/O APIC and local APIC to process all the peripheral
interrupts instead of 8259 PICs. This takes full advantage of the
multicore hardware and the SMP kernel.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Tue, 23 Jun 2015 04:18:51 +0000 (12:18 +0800)]
x86: Add MultiProcessor (MP) table APIs
The MP table provides a way for the operating system to support
for symmetric multiprocessing as well as symmetric I/O interrupt
handling with the local APIC and I/O APIC. We provide a bunch of
APIs for U-Boot to write the floating table, configuration table
header as well as base and extended table entries.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Tue, 23 Jun 2015 04:18:50 +0000 (12:18 +0800)]
x86: Remove inline for lapic access routines
Remove inline for lapic access routines and expose lapic_read()
& lapic_write() as APIs to read/write lapic registers. Also move
stop_this_cpu() to mp_init.c as it has nothing to do with lapic.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Tue, 23 Jun 2015 04:18:49 +0000 (12:18 +0800)]
x86: Add I/O APIC register access routines
I/O APIC registers are addressed indirectly. Add io_apic_read() and
io_apic_write() routines to help register access. Two macros for I/O
APIC ID and version register offset are also added.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Tue, 23 Jun 2015 04:18:47 +0000 (12:18 +0800)]
x86: Reduce PIRQ routing table size
There is no need to populate multiple irq info entries with the same
bus number and device number, but with different interrupt pin. We
can use the same entry to store all the 4 interrupt pin (INT A/B/C/D)
routing information to reduce the whole PIRQ routing table size.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Tue, 23 Jun 2015 04:18:46 +0000 (12:18 +0800)]
x86: Ignore function number when writing PIRQ routing table
In fill_irq_info() pci device's function number is written into
the table, however this is not really necessary. The function
number can be anything as OS doesn't care about this field,
neither does the PIRQ routing specification. Change to always
writing 0 as the function number.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Tue, 23 Jun 2015 04:18:44 +0000 (12:18 +0800)]
x86: queensbay: Correct Topcliff device irqs
There are 4 usb ports on the Intel Crown Bay board, 2 of which are
connected to Topcliff usb host 0 and the other 2 connected to usb
host 1. USB devices inserted in the ports connected to usb host 1
cannot get detected due to wrong IRQ assigned to the controller.
Actually we need apply the PCI interrupt pin swizzling logic to all
devices on the Topcliff chipset when configuring the PIRQ routing.
This was observed on usb ports, but device 6 and 10 irqs are also
wrong. Correct them all together.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Wed, 17 Jun 2015 03:15:39 +0000 (11:15 +0800)]
x86: crownbay: Add MP initialization
Intel Crown Bay board has a TunnelCreek processor which supports
hyper-threading. Add /cpus node in the crownbay.dts and enable
the MP initialization.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
(modified to remove error:
overriding the value of OF_CONTROL. Old value: "y", new value: "y")
Bin Meng [Wed, 17 Jun 2015 03:15:38 +0000 (11:15 +0800)]
x86: Clean up lapic codes
This commit cleans up the lapic codes:
- Delete arch/x86/include/asm/lapic_def.h, and move register and bit
defines into arch/x86/include/asm/lapic.h
- Use MSR defines from msr-index.h in enable_lapic() and disable_lapic()
- Remove unnecessary stuff like NEED_LAPIC, X86_GOOD_APIC and
CONFIG_AP_IN_SIPI_WAIT
- Move struct x86_cpu_priv defines to asm/arch-ivybridge/bd82x6x.h, as
it is not apic related and only used by ivybridge
- Fix coding convention issues
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Wed, 17 Jun 2015 03:15:37 +0000 (11:15 +0800)]
x86: Move lapic_setup() call into init_bsp()
Currently lapic_setup() is called before calling mp_init(), which
then calls init_bsp() where it calls enable_lapic(), which was
already enabled in lapic_setup(). Hence move lapic_setup() call
into init_bsp() to avoid the duplication.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Wed, 17 Jun 2015 03:15:36 +0000 (11:15 +0800)]
x86: Move MP initialization codes into a common place
Most of the MP initialization codes in arch/x86/cpu/baytrail/cpu.c is
common to all x86 processors, except detect_num_cpus() which varies
from cpu to cpu. Move these to arch/x86/cpu/cpu.c and implement the
new 'get_count' method for baytrail and cpu_x86 drivers. Now we call
cpu_get_count() in mp_init() to get the number of CPUs.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Fri, 12 Jun 2015 06:52:23 +0000 (14:52 +0800)]
x86: kconfig: Fix minor nits in MAX_CPUS
Move MAX_CPUS definition after SMP so that it shows below SMP in the
menuconfig. Also replace the leading spaces in the MAX_CPUS section
with tabs to conform coding standard.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Fri, 12 Jun 2015 06:52:20 +0000 (14:52 +0800)]
x86: dm: Clean up cpu drivers
This commit does the following to clean up x86 cpu dm drivers:
- Move cpu_x86 driver codes from arch/x86/cpu/cpu.c to a dedicated
file arch/x86/cpu/cpu_x86.c
- Rename x86_cpu_get_desc() to cpu_x86_get_desc() to keep consistent
naming with other dm drivers
- Add a new cpu_x86_bind() in the cpu_x86 driver which does exactly
the same as the one in the intel baytrail cpu driver
- Update intel baytrail cpu driver to use cpu_x86_get_desc() and
cpu_x86_bind()
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 7 Jun 2015 14:50:32 +0000 (08:50 -0600)]
spi: sf: Print the error code on failure
Rather than just 'ERROR', display the error code, which may be useful, at
least with driver model.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Marek Vasut <marex@denx.de> Reviewed-by: Jagan Teki <jteki@openedev.com>
Bin Meng [Sun, 7 Jun 2015 03:33:14 +0000 (11:33 +0800)]
x86: fsp: Move FspInitEntry call to board_init_f()
The call to FspInitEntry is done in arch/x86/lib/fsp/fsp_car.S so far.
It worked pretty well but looks not that good. Apart from doing too
much work than just enabling CAR, it cannot read the configuration
data from device tree at that time. Now we want to move it a little
bit later as part of init_sequence_f[] being called by board_init_f().
This way it looks and works better in the U-Boot initialization path.
Due to FSP's design, after calling FspInitEntry it will not return to
its caller, instead it jumps to a continuation function which is given
by bootloader with a new stack in system memory. The original stack in
the CAR is gone, but its content is perserved by FSP and described by
a bootloader temporary memory HOB. Technically we can recover anything
we had before in the previous stack, but that is way too complicated.
To make life much easier, in the FSP continuation routine we just
simply call fsp_init_done() and jump back to car_init_ret() to redo
the whole board_init_f() initialization, but this time with a non-zero
HOB list pointer saved in U-Boot's global data so that we can bypass
the FspInitEntry for the second time.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Andrew Bradford <andrew.bradford@kodakalaris.com> Tested-by: Simon Glass <sjg@chromium.org>
Bin Meng [Sun, 7 Jun 2015 03:33:13 +0000 (11:33 +0800)]
x86: fsp: Load GDT before calling FspInitEntry
Currently the FSP execution environment GDT is setup by U-Boot in
arch/x86/cpu/start16.S, which works pretty well. But if we try to
move the FspInitEntry call a little bit later to better fit into
U-Boot's initialization sequence, FSP will fail to bring up the AP
due to #GP fault as AP's GDT is duplicated from BSP whose GDT is
now moved into CAR, and unfortunately FSP calls AP initialization
after it disables the CAR. So basically the BSP's GDT still refers
to the one in the CAR, whose content is no longer available, so
when AP starts up and loads its segment register, it blows up.
To resolve this, we load GDT before calling into FspInitEntry.
The GDT is the same one used in arch/x86/cpu/start16.S, which is
in the ROM and exists forever.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Andrew Bradford <andrew.bradford@kodakalaris.com> Tested-by: Simon Glass <sjg@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Sun, 7 Jun 2015 03:33:12 +0000 (11:33 +0800)]
x86: Add Kconfig options to be used by arch/x86/cpu/config.mk
Add RESET_SEG_START, RESET_SEG_SIZE and RESET_VEC_LOC Kconfig options
and make arch/x86/cpu/config.mk use these options.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Andrew Bradford <andrew.bradford@kodakalaris.com> Tested-by: Simon Glass <sjg@chromium.org>
Andre Przywara [Thu, 2 Jul 2015 00:04:23 +0000 (01:04 +0100)]
scsi: fix compiler warning with DEBUG and 48bit LBAs
Commit 2b42c9317db ("ahci: support LBA48 data reads for 2+TB drives")
introduced conditional code which triggers a warning when compiled
with DEBUG enabled:
In file included from common/cmd_scsi.c:12:0:
common/cmd_scsi.c: In function 'scsi_read':
include/common.h:109:4: warning: 'smallblks' may be used uninitialized in this function [-Wmaybe-uninitialized]
...
Since this is for debug only, take the easy way and initialize the
variable explicitly on declaration to avoid the warning.
(Fix a nearby whitespace error on the way.)
Tested-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Andre Przywara <osp@andrep.de>
The type of the "size" of "struct mtd_info" is uint64_t, while
mtd_arg_off_size() and mtd_arg_off() treat chipsize as int type.
The chipsize is wrapped around if the argument is given with 2GB
or larger.
Stefan Roese [Mon, 29 Jun 2015 12:58:12 +0000 (14:58 +0200)]
block: ahci: Don't enable port interrupts
This patch changes the initialization of the AHCI controller to not
enable the default interrupts (DEF_PORT_IRQ). As interrupts are
not used in U-Boot in general, this should not break the common AHCI
driver operation.
This change is needed to support the Marvell Armada 38x AHCI
controller. With interrupts enabled, this results in timeouts in
ahci_device_data_io(). Not enabling these interrupts fixes this
problem and the common AHCI driver works fine.
Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@konsulko.com> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Luka Perkov <luka.perkov@sartura.hr>
Stefan Roese [Mon, 29 Jun 2015 12:58:10 +0000 (14:58 +0200)]
arm: mvebu: Add SDIO/SDHCI support for Armada A38x
Armada A38x implements an SDHCI compatible SDIO controller. This patch
enables the Marvell driver to support this SoC. And enables the
SDIO controller if selected by the board configuration.
projects / u-boot / log