Timur Tabi [Tue, 15 Jan 2008 23:09:41 +0000 (17:09 -0600)]
Remove #undef DEBUG from MPC83xx board header files
Remove the "#undef DEBUG" line from all Freescale 83xx board header files.
The inclusion of this line makes it impossible to enable debug code in
other source files, because "#define DEBUG" typically needs to be defined
before any header files are included.
allow to use a different server as set in serverip
add CONFIG_TFTP_FILE_NAME_MAX_LEN to configure the file name length
if not defined the max length will be at 128
Wolfgang Denk [Thu, 27 Dec 2007 09:56:54 +0000 (10:56 +0100)]
OMAP5912: fix FIFO handling in UART driver
According to the OMAP5912 Serial Interfaces Reference Guide (see
http://focus.ti.com/lit/ug/spru760c/spru760c.pdf, page 150), the
FIFO_EN enable bit in the FIFO Control Register (FCR) can only be
changed when the baud clock is not running, i. e. when both DLL and
DLH are set to 0.
Thus make sure that DLL and DLH are 0 when writing the FCR.
Harald Welte [Wed, 19 Dec 2007 13:19:38 +0000 (14:19 +0100)]
ARM: arm920/s3c24xx: IRQ demulitplexer callback
This patch adds a IRQ demultiplexer callback to the arm920 cpu core code,
plus a stub implementation of it for the S3C2410.
The purpose is to allow arm920t implementations such as the s3c24x0 to
implement interrupt handlers in u-boot without having to touch core
arm920t code.
Signed-off-by: Harald Welte <laforge@openmoko.org>
Ladislav Michl [Thu, 6 Dec 2007 21:59:16 +0000 (22:59 +0100)]
ARM: Fix at91rm9200dk base address
Somewhere during development of U-Boot-1.1.3 CONFIG_BOOTBINFUNC was
renamed into CONFIG_INIT_CRITICAL which was 04 Apr 2005 replaced
with CONFIG_SKIP_LOWLEVEL_INIT and CONFIG_SKIP_RELOCATE_UBOOT.
However CONFIG_SKIP_LOWLEVEL_INIT has oposite meaning to
CONFIG_BOOTBINFUNC, so fix configuration to reflect this fact.
I'm sending this patch 4th (!) time in hope it produces at least some
reaction.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Fix at91rm9200dk base and environment address.
stefano babic [Tue, 20 Nov 2007 09:40:24 +0000 (10:40 +0100)]
MMC for PXA 27X (resubmit)
MMC support for X_Scale PXA is broken and does not work.
Mainly, the mmc_init() function cannot recognize current SD/MMC cards.
There were already some patches around the world but none of them was
merged into the official u-boot tree.
This patch makes order fixing this issue. Resubmit after code cleanup.
stefano babic [Tue, 20 Nov 2007 09:37:04 +0000 (10:37 +0100)]
Fix gcc issues in pxa-regs.h
Fix gcc4 issue. With some toolchain, a previous patch that fixes gcc4
issues generates wrong code.
(Problem was reported with gcc-4.0.2-glibc-2.3.6/arm-softfloat-linux-gnu).
This patch fixes the problem and solves the gcc-4 issues as the linux
kernel does.
Becky Bruce [Wed, 23 Jan 2008 22:31:00 +0000 (16:31 -0600)]
86xx: Rearrange the sequence in start.S
* split the BAT initialization so that only 2 BATs (for the boot page
and stack) are programmed very early on. The rest are initialized later.
* Move other BAT setup, ccsrbar setup, and law setup later in the code
after translation has been enabled.
These changes will facilitate the moving of law and BAT initialization
to C code, and will aid with 36-bit physical addressing support.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
The patch adds 4 boards, called AcTux-1 .. AcTux-4. This patch contains the
files that
contain changes for multiple boards, the board-specific files follow as
separate patches.
Signed-off-by: Michael Schwingen <michael@schwingen.org>
enables the RTS signal with CONFIG_SERIAL_RTS_ACTIVE.
No handshaking is done, but the active RTS signal allows to
connect to the target using a PC which is using RTS/CTS
handshake, and does no harm if the PC is set to ignore RTS.
Signed-off-by: Michael Schwingen <michael@schwingen.org>
load ixp42x NPE firmware from separate flash block, remove dead code
Hi,
the following patch adds support to move the IXP42X NPE firmware to a
separate flash block, whose start address is defined in
CONFIG_IXP4XX_NPE_EXT_UCODE_BASE. Using that, it is possible to build
NPE-enabled u-boot without copyright problems due to the NPE firmware.
I hope the patch applies, I get whitespace-related differences in the NPE
files due to trailing whitespace in the original versions.
Signed-off-by: Michael Schwingen <michael@schwingen.org> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Haiying Wang [Wed, 16 Jan 2008 22:12:12 +0000 (17:12 -0500)]
FSL: Fix common EEPROM_data structure definition
- Fix EEPROM_data structure definition according to System EEPROM Data Format.
- Read MAC addresses from EEPROM to ethXaddr before saving ethXaddr to
bd->bi_ethaddr.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Ben Warren [Thu, 17 Jan 2008 03:37:35 +0000 (22:37 -0500)]
Add support for a Freescale non-CPM SPI controller
This patch adds support for the SPI controller found on Freescale PowerPC
processors such as the MCP834x family. Additionally, a new config option,
CONFIG_HARD_SPI, is added for general purpose SPI controller use.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Matthias Fuchs [Thu, 17 Jan 2008 06:45:05 +0000 (07:45 +0100)]
net: add 'ethrotate' environment variable
[PATCH] net: add 'ethrotate' environment variable
This patch replaces the buildtime configuration option
CONFIG_NET_DO_NOT_TRY_ANOTHER through the 'ethrotate' runtime
configuration veriable. See README.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Niklaus Giger [Wed, 16 Jan 2008 17:39:20 +0000 (18:39 +0100)]
ppc4xx: Netstal HCU4 board: added various fixes and POST
- Moved some common code to netstal/common/nm_bsp.c.
- sdram initialisation goes go netstal/common/fixed_sdram.c.
- Added support for POST.
- Stylistic cleanups (multi-line comments/ enforce 80 colomn width)
Niklaus Giger [Thu, 17 Jan 2008 11:53:56 +0000 (12:53 +0100)]
ppc4xx: netstal/common define routines used by all boards
Added some routines used by all Netstal boards:
- nm_bsp.c: - nm_show_print and
- common_misc_init_r
- set_params_for_sw_install. Very specific code to handle our SW
installation procedure
- fixed_sdram.c: Common routines for HCU4 (and upcoming) MCU25 boards
to handle sdram initialization.
- nm.h: Common header
projects / u-boot / log