Ladislav Michl [Sat, 18 Feb 2017 23:23:39 +0000 (00:23 +0100)]
igep00x0: disable environment
ISEE's U-Boot and Linux are using 1bit ECC scheme, while we
switched to 8bit ECC to fullfill flash specification requirements.
However when trying to run U-Boot on board with 1bit ECC'd data
on flash, UBI code takes several minutes to pass scan as reading
of every block ends with ecc error (which is also printed on
console).
So, until proper solution is developed, disable environment
alltogether.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Patrice Chotard [Tue, 21 Feb 2017 12:37:12 +0000 (13:37 +0100)]
board: Add STMicroelectronics STiH410-B2260 support
This is a 96Board compliant board based on STiH410 SoC:
- 1GB DDR
- On-Board USB combo WiFi/Bluetooth RTL8723BU
with PCB soldered antenna
- Ethernet 1000-BaseT
- SATA
- HDMI
- 2 x USB2.0 type A
- 1 x USB2.0 type micro-AB
- SD card slot
- High speed connector (SD/I2C/USB interfaces)
- Low speed connector (UART/I2C/GPIO/SPI/PCM interfaces)
Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Patrice Chotard [Tue, 21 Feb 2017 12:37:09 +0000 (13:37 +0100)]
STiH410: Add STi SDHCI driver
Add SDHCI host controller found on STMicroelectronics SoCs
On some ST SoCs, i.e. STiH407/STiH410, the MMC devices can live
inside a dedicated flashSS sub-system that provides an extend subset
of registers that can be used to configure the Arasan MMC/SD Host
Controller.
This means, that the SDHCI Arasan Controller can be configured to be
eMMC4.5 or 4.3 spec compliant.
W/o these settings the SDHCI will configure and use the MMC/SD
controller with limited features e.g. PIO mode, no DMA, no HS etc.
Patrice Chotard [Tue, 21 Feb 2017 12:37:07 +0000 (13:37 +0100)]
STiH410: Add STi serial driver
This patch adds support to ASC (asynchronous serial controller)
driver, which is basically a standard serial driver. This IP
is common across other STMicroelectronics SoCs
Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Phil Edworthy [Fri, 17 Feb 2017 08:22:17 +0000 (08:22 +0000)]
armv7m: Add SysTick timer driver
The SysTick is a 24-bit down counter that is found on all ARM Cortex
M3, M4, M7 devices and is always located at a fixed address.
The number of reference clock ticks that correspond to 10ms is normally
defined in the SysTick Calibration register's TENMS field. However, on some
devices this is wrong, so this driver allows the clock rate to be defined
using CONFIG_SYS_HZ_CLOCK.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> Reviewed-by: Vikas MANOCHA <vikas.manocha@st.com>
Lokesh Vutla [Wed, 15 Feb 2017 13:12:54 +0000 (18:42 +0530)]
tools: omapimage: Fix size in header
The size field in GP header that is expected by ROM is size of the
image + size of the header. But omapimage generates a gp header
only with size of the image as size field. Fix it
arm: omap3: Bring back ARM errata workaround 725233
The workaround for ARM errata 725233 had been lost since
commit 45bf05854bc94e (armv7: adapt omap3 to the new cache
maintenance framework). Bring it back in order to avoid
very difficult to reproduce, but actually encountered in
the wild CPU deadlocks when running software rendered
X11 desktop on OMAP3530 hardware.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Migrate to Kconfig] Signed-off-by: Tom Rini <trini@konsulko.com>
arm: omap3: Compile clock.c with -marm option to unbreak OMAP3530
Boards with OMAP3530 SoC fail to boot since commit bd2c4522c26d5
("ti: armv7: enable EXT support in SPL (using ti_armv7_common.h)")
because it enabled the use of Thumb2 for the SPL.
Experiments have shown that the deadlock happens in the
prcm_init() function from 'arch/arm/mach-omap2/omap3/clock.c'.
This patch enforces the compilation of clock.c source file in
ARM mode and makes the deadlock disappear. We are yet to figure
out the root cause of the problem. Still this is somewhat
better than having non-bootable boards for years.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Masahiro Yamada [Mon, 6 Mar 2017 20:28:25 +0000 (05:28 +0900)]
ARM: uniphier: set DRAM_SPARSE flag for LD21 boards
Commit 04cd4e7215d3 ("ARM: uniphier: remove DRAM base address from
board parameters") accidentally unset the DRAM_SPARSE flag, and
changed the physical map of the DRAM channels. Revive the original
behavior.
Fixes: 04cd4e7215d3 ("ARM: uniphier: remove DRAM base address from board parameters") Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reported-by: Shunji Sato <sato.shunji@socionext.com>
arm: omap-common: Fix typo in CONFIG_OMAP54XX guard
Some initialization was unintentionally being skipped on omap5.
Fixes: f5af0827f276 ("arm: omap-common: Guard some parts of the code with CONFIG_OMAP44XX/OMAP54XX") Signed-off-by: Matthijs van Duin <matthijsvanduin@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Ladislav Michl [Mon, 6 Mar 2017 12:54:30 +0000 (13:54 +0100)]
arm: OMAP2+: nandecc: propagate error to command return status
Currently nandecc returns zero even if underlaying
omap_nand_switch_ecc function fails. Fix that by
propagating error returned to command return value.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Tom Rini [Tue, 7 Mar 2017 12:13:42 +0000 (07:13 -0500)]
ARM: Migrate errata to Kconfig
This moves all of the current ARM errata from various header files and in to
Kconfig. This allows for a minor amount of cleanup as we had some instances
where both a general common header file was enabling errata as well as the
board config. We now just select these once at the higher level in Kconfig
Tom Rini [Fri, 3 Mar 2017 20:33:30 +0000 (15:33 -0500)]
am335x_evm: Switch to using imply keyword
These particular SPL options are part of what the ROM provides, but for
compatibility with how we have previously used them, move them to being
implied by the board being selected.
Tom Rini [Fri, 3 Mar 2017 20:33:29 +0000 (15:33 -0500)]
kconfiglib.py: Kludge in 'imply' support
Currently upstream does not yet understand the imply keyword. For what
we use kconfiglib.py for today, this is OK. We only need to be able to
evaluate in order to make boards.cfg and none of those choices will
depend on how imply evaluates out.
Ryan Harkin [Thu, 2 Mar 2017 17:45:16 +0000 (17:45 +0000)]
do_smhload: fix return code
do_smhload was using a ulong to store the return value from
smh_load_file. That returns an int, where -1 indicates an error. As a
ulong will never be negative, smh_load_file errors were not detected and
so_smhload always returned zero.
Also, when errors were spotted, do_smhload was returning 1, rather than
the enumeration CMD_RET_FAILURE (which is also 1).
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Masahiro Yamada [Mon, 27 Feb 2017 06:24:45 +0000 (15:24 +0900)]
kbuild: turn of dtc unit address warnings by default
DTC 1.4.2 or later checks DT unit-address without reg property and
vice-versa, and generates lots of warnings. Fixing DT files will
take for a while. Until then, let's turn off the check unless
building with W=*.
Introduce a new helper dtc-option to check if the option is supported
in order to suppress warnings on older versions.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Bin Meng <bmeng.cn@gmail.com>
Adam Ford [Wed, 8 Mar 2017 03:27:52 +0000 (21:27 -0600)]
omap3_logic: Move SPL Stack into SDRAM
A previous patch broke the board. This patch will add missing part
from the previous patch and also move the SPL Stack into SDRAM at
0x82000000.
Tested with GCC 4.8.2 and GCC 6.2
Fixes: 0959649dc6d9 ("omap3_logic: Switch to simple malloco in SPL") Signed-off-by: Adam Ford <aford173@gmail.com>
Changes in V2:
- Keep CONFIG_SPL_SYS_MALLOC_SIMPLE
- Add CONFIG_SYS_MALLOC_F_LEN=0x2000 (8 MB)
Andre Przywara [Mon, 6 Mar 2017 01:13:38 +0000 (01:13 +0000)]
video: cfb_console: fix 32-bit display on 64-bit architectures
"unsigned long" is a lousy data type when it comes to match peripheral
hardware registers with a fixed size.
Just do the obvious and match a 32-bit display format with an "u32"
data type for casting.
This fixes the logo display on 64-bit architectures, which produced
a black line on the right side of the logo with non-black backgrounds.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Nathan Rossi [Sun, 5 Mar 2017 14:36:23 +0000 (00:36 +1000)]
net: zynq_gem: Fix masking of supported phydev features
When the zynq_gem driver initializes the phy it sets the supported
features that the phy can support and advertise. However instead of
masking the supported features such that it limits the available
features it sets the phy to have the exact supported features of the
zynq_gem. This is problematic as it will enable features that a phy does
not have or cannot advertise.
Specifically this appears as an issue when using a phy that is only
capable of 10/100, but the zynq_gem driver will override this and try to
enable and advertise 10/100/1000.
Reported-by: Arno Steffens <star@gmx.li> Fixes: 80243528ef ("net: gem: Fix gem driver on 1Gbps LAN") Signed-off-by: Nathan Rossi <nathan@nathanrossi.com> Tested-by: Arno Steffens <star@gmx.li> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Michal Simek <michal.simek@xilinx.com>
Wenyou Yang [Tue, 14 Feb 2017 08:24:40 +0000 (16:24 +0800)]
net: macb: Fix ETH not found when clock not support
For the boards such as smartweb on which the clock driver isn't
supported, the ethernet fail to be found when booting up with
the below log.
---8<---
Net: No ethernet found.
--->8---
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Tested-by: Heiko Schocher <hs@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Philipp Tomsich [Wed, 1 Mar 2017 20:04:15 +0000 (21:04 +0100)]
armv8: spl: Call spl_relocate_stack_gd for ARMv8
As part of the startup process for boards using the SPL, we need to
call spl_relocate_stack_gd. This is needed to set up malloc with its
DRAM buffer.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Albert ARIBAUD [Mon, 27 Feb 2017 19:19:07 +0000 (20:19 +0100)]
armv5te: make 'ret lr' produce iinterworking 'bx lr'
Current ARM assembler helper for the 'return to caller' pseudo-instruction
turns 'ret lr' into 'mov pc, lr' for ARMv5TE. This causes the core to remain
in its current ARM state even when the routine doing the 'ret' was called
from Thumb-1 state, triggering an undefined instruction exception.
This causes early run-time failures in all boards compiled using the Thumb-1
instruction set (for instance the Open-RD family).
ARMv5TE supports 'bx lr' which properly implements interworking and thus
correctly returns to Thumb-1 state from ARM state.
This change makes 'ret lr' turn into 'bx lr' for ARMv5TE.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Andrew F. Davis [Wed, 22 Feb 2017 23:46:39 +0000 (17:46 -0600)]
arm: mach-omap2: Flush cache after FIT post-processing image
After we authenticate/decrypt an image we need to flush the caches
as they may still contain bits of the encrypted image. This will
cause failures if we attempt to jump to this image.
Reported-by: Yogesh Siraswar<yogeshs@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Jonathan Golder [Fri, 24 Feb 2017 16:46:10 +0000 (17:46 +0100)]
splash: Prevent splash_load_fs from writing to 0x0
Passing NULL to fs_read() for actread value results in hanging U-Boot
at least on our ARM plattform (TI AM335x). Since fs_read() and
following functions do not catch nullpointers, writing to 0x0 occurs.
Passing a local dummy var instead of NULL solves this issue.
Signed-off-by: Jonathan Golder <jonathan.golder@kurz-elektronik.de> Cc: Anatolij Gustschin <agust@denx.de>
Tom Rini [Sun, 26 Feb 2017 20:23:18 +0000 (15:23 -0500)]
travis-ci: Temporarily disable using a newer device tree compiler
For a long while dtc has warned about various constructs. This is now
leading to log file size being exceeded in travis, and as the majority
of these errors need to be fixed in the kernel, switch to using the
stock device-tree-compiler package.
Felipe Balbi [Wed, 22 Feb 2017 09:22:37 +0000 (11:22 +0200)]
usb: gadget: g_dnl: fix g_dnl_set_serialnumber()
instead of only copying if strlen(s) is less than 32 characters, let's
just copy at most 31 characters regardless of the size of
serial#. This will guarantee that we always have a serial number if
serial# environment variable is set to anything.
Note that without a proper serial number, USB Command Verifier fails
our test of Device Descriptor since we will claim to have a serial
number without really providing one when requested.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Felipe Balbi [Fri, 10 Feb 2017 16:32:31 +0000 (19:32 +0300)]
usb: gadget: f_dfu: write req->actual bytes
If last packet is short, we shouldn't write req->length bytes to
non-volatile media, we should write only what's available to us, which
is held in req->actual.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Patrick Delaunay [Fri, 16 Dec 2016 17:41:31 +0000 (18:41 +0100)]
usb: gadget: dfu: correct size for USB_REQ_DFU_GETSTATE result
return the correct size for DFU_GETSTATE result (1 byte in DFU 1.1 spec)
to avoid issue in USB protocol and the variable "value" is propagated
to req->lenght as all the in the other request with answer
- DFU_GETSTATUS
- DFU_DNLOAD
- DFU_UPLOAD
Then the buffer is correctly treated in USB driver
NB: it was the only request witch directly change "req->actual"
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
usb: gadget: dfu: add functional descriptor in descriptor set
The "DFU descriptor set" must contain the "DFU functional descriptor"
but it is missing today in U-Boot code
(cf: DFU spec 1.1, chapter 4.2 DFU Mode Descriptor Set)
This patch only allocate buffer and copy DFU functional descriptor
after interfaces.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
Masahiro Yamada [Mon, 20 Feb 2017 09:34:20 +0000 (18:34 +0900)]
ARM: uniphier: add simple eMMC load APIs instead of ROM API
Re-use of routines embedded in the Boot ROM requires a function
pointer table for each SoC. This is not nice in terms of the
maintainability in a long run.
Implement simple eMMC load APIs that are commonly used for LD11,
LD20, and hopefully future SoCs.
Masahiro Yamada [Fri, 17 Feb 2017 07:17:22 +0000 (16:17 +0900)]
ARM: uniphier: deassert RST_n of eMMC device for LD11/LD20
For LD11 and LD20 SoCs, the RST_n pin is asserted by default. If
the EXT_CSD[162], bit[1:0] (RST_n_ENABLE) is fused, the eMMC device
would stay in the reset state until its RST_n pin is deasserted by
software.
Currently, this is cared by an ad-hoc way because the eMMC hardware
reset provider is not supported in U-Boot for now. This code should
be re-written once the "mmc-pwrseq-emmc" binding is supported.
Kotaro Hayashi [Tue, 14 Feb 2017 02:39:14 +0000 (11:39 +0900)]
ARM: uniphier: add DRAM PHY clock duty adjustment for LD20 SoC
If the DRAM clock duty does not meet the allowable tolerance,
it is marked in an efuse register. If the register is fused,
the boot code should compensate for the DRAM clock duty error.
Masahiro Yamada [Mon, 13 Feb 2017 16:24:26 +0000 (01:24 +0900)]
ARM: uniphier: rework spl_boot_device() and related code
The current implementation has ugly switch statements here and there,
and duplicates similar code. Rework it using table lookups for SoC
data and reduce code duplication.
Masahiro Yamada [Mon, 13 Feb 2017 16:24:25 +0000 (01:24 +0900)]
ARM: uniphier: move spl_boot_mode() to a separate file
The spl_boot_mode() is unrelated to the other code in this file.
Besides, this function is only called from common/spl/spl_mmc.c,
so it is reasonable to guard with CONFIG_SPL_MMC_SUPPORT.
Masahiro Yamada [Mon, 13 Feb 2017 16:24:24 +0000 (01:24 +0900)]
ARM: uniphier: move MMC code to a separate file
Currently, arch/arm/mach-uniphier/boot-mode/boot-mode.c is messed up
with unrelated code; there is no reason why the "mmcsetn" command
must be placed in this file.
Split out the MMC code into arch/arm/mach-uniphier/mmc-first-dev.c.
Masahiro Yamada [Sun, 12 Feb 2017 14:44:57 +0000 (23:44 +0900)]
ARM: dts: uniphier: drop u-boot, dm-pre-reloc from system-bus pinctrl node
Since commit 26b09c022ab6 ("ARM: uniphier: move SBC and Support Card
init code to U-Boot proper"), SPL does not need pin-mux settings for
the System Bus.
Masahiro Yamada [Sun, 12 Feb 2017 09:21:16 +0000 (18:21 +0900)]
ARM: uniphier: rename second stage loader name
For the memory footprint reason, the Boot ROM can not load the ARM
Trusted Firmware BL1 directly when Trusted Board Boot is enabled.
The second stage loader is Socionext's own firmware, so rename it
for clarification.
Masahiro Yamada [Sun, 12 Feb 2017 09:21:15 +0000 (18:21 +0900)]
pinctrl: uniphier: support pin configuration
Support the following DT properties:
"bias-disable"
"bias-pull-up"
"bias-pull-down"
"bias-pull-pin-default"
"input-enable"
"input-disable"
My main motivation is to support pull up/down biasing. For Pro5 and
later SoCs, the pupdctrl register number is the same as the pinmux
number, so this feature can be supported without having big pin
tables.
Masahiro Yamada [Sun, 5 Feb 2017 01:52:12 +0000 (10:52 +0900)]
ARM: uniphier: remove DRAM base address from board parameters
The base address of each DRAM channel can be calculated from other
parameters, so does not need hard-coding. What we need is the size
of each DRAM channel and DRAM_SPARSE flag to decide the start address
of DRAM channel 1.
Masahiro Yamada [Mon, 30 Jan 2017 04:12:28 +0000 (13:12 +0900)]
ARM: uniphier: update README.uniphier for latest build instruction
Since commit c0efc3140e75 ("ARM: uniphier: change CONFIG_SPL_PAD_TO
to 128KB"), the u-boot.bin should be burned at the offset 0x20000.
I missed to update README.uniphier in that commit. Now updating.
Masahiro Yamada [Mon, 20 Feb 2017 08:32:19 +0000 (17:32 +0900)]
ARM: uniphier: print Support Card info very late
Since commit 26b09c022ab6 ("ARM: uniphier: move SBC and Support Card
init code to U-Boot proper"), the System Bus is initialized by
board_init(). The show_board_info() is called from board_init_f()
by default, so the revision register of the Micro Support Card may
not be accessed at this point. Show its revision after the System
Bus is initialized.
Commit a8e6300d483d ("ARM: uniphier: refactor spl_init_board()")
accidentally dropped dcache_disable() call. Since then, the SPL of
LD11 and LD20 failed to load U-Boot proper.
Fabio Estevam [Wed, 22 Feb 2017 13:40:22 +0000 (10:40 -0300)]
video: mxsfb: Fix reset hang when videomode variable is not present
Currently the system hangs when the 'videomode' variable is not present
and a reset command is issued:
=> setenv videomode
=> saveenv
=> reset
(Board hangs)
lcdif_power_down() assumes that the LCDIF controller has been properly
configured and enabled, which may not be true.
To fix this issue check whether panel.frameAdrs has been initialized and
in case it has not been initialized, do not continue with the LCDIF
powerdown sequence.
Andy Shevchenko [Fri, 17 Feb 2017 13:49:00 +0000 (16:49 +0300)]
x86: Intel MID platforms has no microcode update
There is no microcode update available for SoCs used on Intel MID
platforms.
Use conditional to bypass it.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Vincent Tinelli [Fri, 17 Feb 2017 13:48:59 +0000 (16:48 +0300)]
x86: zImage: add Intel MID platforms support
Intel MID platform boards have special treatment, such as boot parameter
setting.
Assign hardware_subarch accordingly if CONFIG_INTEL_MID is set.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Andy Shevchenko [Fri, 17 Feb 2017 13:48:58 +0000 (16:48 +0300)]
x86: Introduce INTEL_MID quirk option
Intel Mobile Internet Device (MID) platforms have special treatment in
some cases, such as CPU enumeration or boot parameters configuration.
Besides that several drivers are specifically developed for the IP
blocks found on Intel MID platforms. Those drivers will be dependent to
this option.
Here we introduce specific quirk option for such cases.
It is supposed to be selected by Intel MID platform boards, for example,
Intel Edison.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
J. Tang [Fri, 10 Feb 2017 02:54:13 +0000 (21:54 -0500)]
x86: Force 32-bit jumps in interrupt handlers
Depending upon the compiler used, IRQ entries could vary in sizes. With
GCC 5.x, the code generator will use short jumps for some IRQ entries
but near jumps for others. For example, GCC 5.4.0 generates the
following:
This causes a problem in cpu_init_interrupts(), because the IDT setup
assumed same sizes for all IRQ entries. GCC 4.x always generated 32-bit
jumps, so this previously was not a problem.
The fix is to force 32-bit near jumps for all entries within the
inline assembly. This works for GCC 5.x, and 4.x was already using
that form of jumping.
Signed-off-by: Jason Tang <tang@jtang.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Andrey Yurovsky [Fri, 10 Feb 2017 18:33:34 +0000 (10:33 -0800)]
mtd: nand: build MXS driver for MX7 as well
The i.MX7 has the same GPMI controller as i.MX6 and is covered by the MXS
driver. Tell Kconfig that we can use this driver on the MX7 platform (the MXS
driver already has the few i.MX7-specific changes needed for basic operation
and the board itself sets the pinmux correctly).
Tested on i.MX7D with the Sabre board and a NAND Flash soldered to U12.
Peter Robinson [Tue, 14 Feb 2017 13:10:12 +0000 (13:10 +0000)]
mx6sx: udoo_neo: Enable distro boot options in config
The include/configs/udoo_neo.h already includes the distro defaults
include files so it seems the board was missed in the move to the
config file, whether that in initial commit or conversion, so
enable the option now and remove duplicated settings.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Peter Robinson [Tue, 14 Feb 2017 13:10:11 +0000 (13:10 +0000)]
mx6sx: udoo_neo: use different load address for ramdisk
The fdt_addr and ramdisk_addr_r are currently both defined to
0x83000000 and that's not going to work well for anyone. Move
the ramdisk_addr_r to 0x84000000.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
projects / u-boot / log