Stefan Roese [Thu, 26 Jun 2008 11:40:57 +0000 (13:40 +0200)]
ppc4xx: Consolidate PPC4xx UIC defines
This 2nd patch now removes all UIC mask bit definition. They should be
generated from the vectors by using the UIC_MASK() macro from now on.
This way only the vectors need to get defined for new PPC's.
Also only the really used interrupt vectors are now defined. This makes
definitions for new PPC versions easier and less error prone.
Another part of this patch is that the 4xx emac driver got a little
cleanup, since now the usage of the interrupts is clearer.
Stefan Roese [Wed, 25 Jun 2008 08:59:22 +0000 (10:59 +0200)]
ppc4xx: Consolidate PPC4xx UIC defines
This patch is the first step to consolidate the UIC related defines in the
4xx headers. Move header from asm-ppc/ppc4xx-intvec.h to
asm-ppc/ppc4xx-uic.h as it will hold all UIC related defines in the next
steps.
Stefan Roese [Thu, 10 Jul 2008 11:52:44 +0000 (13:52 +0200)]
ppc4xx: Remove redundant ft_board_setup() functions from some 4xx boards
This patch removes some ft_board_setup() functions from some 4xx boards.
This can be done since we now have a default weak implementation for this
in cpu/ppc4xx/fdt.c. Only board in need for a different/custom
implementation like canyonlands need their own version.
Grant Erickson [Tue, 8 Jul 2008 15:35:00 +0000 (08:35 -0700)]
ppc4xx: Add MII mode support to the EMAC RGMII Bridge
This patch adds support for placing the RGMII bridge on the
PPC405EX(r) into MII/GMII mode and allows a board-specific
configuration to specify the bridge mode at compile-time.
Signed-off-by: Grant Erickson <gerickson@nuovations.com> Signed-off-by: Stefan Roese <sr@denx.de>
Grant Erickson [Wed, 9 Jul 2008 23:46:35 +0000 (16:46 -0700)]
ppc4xx: Add Mnemonics for AMCC/IBM DDR2 SDRAM Controller
This patch completes the preprocessor mneomics for the IBM DDR2 SDRAM
controller registers (MODT and INITPLR) used by the
PowerPC405EX(r). The MMODE and MEMODE registers are unified with their
peer values used for the INITPLR MR and EMR registers,
respectively. Finally, a spelling typo is correct (MANUEL to MANUAL).
With these mnemonics in place, the CFG_SDRAM0_* magic numbers for
Kilauea are replaced by equivalent mnemonics to make it easier to
compare and contrast other 405EX(r)-based boards (e.g. during board
bring-up).
Finally, unified the SDRAM controller register dump routine such that
it can be used across all processor variants that utilize the IBM DDR2
SDRAM controller core. It produces output of the form:
PPC4xx IBM DDR2 Register Dump:
...
SDRAM_MB0CF[40] = 0x00006701
...
which is '<mnemonic>[<DCR #>] = <value>'. The DCR number is included
since it is not uncommon that the DCR values in header files get mixed
up and it helps to validate, at a glance, they match what is printed
in the user manual.
Tested on:
AMCC Kilauea/Haleakala:
- NFS Linux Boot: PASSED
- NAND Linux Boot: PASSED
Signed-off-by: Grant Erickson <gerickson@nuovations.com> Signed-off-by: Stefan Roese <sr@denx.de>
Grant Erickson [Wed, 9 Jul 2008 23:31:59 +0000 (16:31 -0700)]
ppc4xx: Add AMCC/IBM DDR2 SDRAM ECC Field Mnemonics
Add additional DDR2 SDRAM memory controller DCR mneomnics, condition
revision ID DCR based on 405EX, and add field mnemonics for bus error
status and ECC error status registers.
Signed-off-by: Grant Erickson <gerickson@nuovations.com> Signed-off-by: Stefan Roese <sr@denx.de>
Grant Erickson [Wed, 9 Jul 2008 18:55:46 +0000 (11:55 -0700)]
PPC4xx: Correct SDRAM_MCSTAT for PPC405EX(r)
While the PowerPC 405EX(r) shares in common the AMCC/IBM DDR2 SDRAM
controller core also used in the 440SP, 440SPe, 460EX, and 460GT, in
the 405EX(r), SDRAM_MCSTAT has a different DCR value.
Its present value on the 405EX(r) causes a read back of 0xFFFFFFFF
which causes SDRAM initialization to periodically fail since it can
prematurely indicate SDRAM ready status.
Signed-off-by: Grant Erickson <gerickson@nuovations.com> Signed-off-by: Stefan Roese <sr@denx.de>
Feng Kan [Wed, 9 Jul 2008 05:48:42 +0000 (22:48 -0700)]
ppc4xx: Initial framework of the AMCC PPC460SX redwood reference board.
Add AMCC Redwood reference board that uses the latest
PPC 464 CPU processor combined with a rich mix of peripheral
controllers. The board will support PCIe, mutiple Gig ethernet
ports, advanced hardware RAID assistance and IEEE 1588.
Signed-off-by: Feng Kan <fkan@amcc.com> Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes a potentially serious issue related to USB which was
discouvered by Martin Krause <martin.krause@tqs.de> and fixed for
ARM920T. Martin wrote:
Turn off USB to prevent the host controller from writing to the
SDRAM while Linux is booting. This could happen, because the HCCA
(Host Controller Communication Area) lies within the SDRAM and the
host controller writes continously to this area (as busmaster!), for
example to increase the HccaFrameNumber variable, which happens
every 1 ms.
This is a slightly modified version of the patch in order to shutdown
USB when booting on all architectures.
Harald Welte [Sun, 6 Jul 2008 16:58:05 +0000 (00:58 +0800)]
fix USB devices with multiple configurations
This patch fixes bugs in usbdcore*.c related to the use of devices
with multiple configurations.
The original code made mistakes about the meaning of configuration value and
configuration index, and the resulting off-by-one errors resulted in:
* SET_CONFIGURATION always selected the first configuration, no matter what
wValue is being passed.
* GET_DESCRIPTOR/CONFIGURATION always returned the descriptor for the first
configuration (index 0).
Signed-off-by: Harald Welte <laforge@openmoko.org> Acked-by: Markus Klotzbuecher <mk@denx.de>
Harald Welte [Sun, 6 Jul 2008 16:58:05 +0000 (00:58 +0800)]
fix USB devices with multiple configurations
This patch fixes bugs in usbdcore*.c related to the use of devices
with multiple configurations.
The original code made mistakes about the meaning of configuration value and
configuration index, and the resulting off-by-one errors resulted in:
* SET_CONFIGURATION always selected the first configuration, no matter what
wValue is being passed.
* GET_DESCRIPTOR/CONFIGURATION always returned the descriptor for the first
configuration (index 0).
Signed-off-by: Harald Welte <laforge@openmoko.org> Acked-by: Markus Klotzbuecher <mk@denx.de>
Stefan Roese [Thu, 10 Jul 2008 08:10:54 +0000 (10:10 +0200)]
MTD/NAND: Fix printf format warning in nand code
This patch fixes NAND related printf format warning. Those warnings are
now visible since patch dc4b0b38d4aadf08826f6c31270f1eecd27964fd
[Fix printf errors.] by Andrew Klossner has been applied. Thanks, this is
really helpful.
Stefan Roese [Tue, 8 Jul 2008 10:01:47 +0000 (12:01 +0200)]
pci: Move PCI device configuration check into a separate weak function
This patch moves the check, if a device should be skipped in PCI PNP
configuration into the function pci_skip_dev(). This function is defined
as weak so that it can be overwritten by a platform specific one if
needed. The check if the device should get printed in the PCI summary upon
bootup (when CONFIG_PCI_SCAN_SHOW is defined) is moved to the function
pci_print_dev() which is also defined as weak too.
Stefan Roese [Thu, 10 Jul 2008 07:58:06 +0000 (09:58 +0200)]
ppc4xx: Fix printf format warnings now visible with the updated format check
This patch fixes ppc4xx related printf format warning. Those warnings are
now visible since patch dc4b0b38d4aadf08826f6c31270f1eecd27964fd
[Fix printf errors.] by Andrew Klossner has been applied. Thanks, this is
really helpful.
Stefan Roese [Wed, 9 Jul 2008 15:33:57 +0000 (17:33 +0200)]
ppc4xx: Enable support for > 2GB SDRAM on AMCC Katmai
Newer PPC's like 440SPe, 460EX/GT can be equipped with more than 2GB of SDRAM.
To support such configurations, we "only" map the first 2GB via the TLB's. We
need some free virtual address space for the remaining peripherals like, SoC
devices, FLASH etc.
Note that ECC is currently not supported on configurations with more than 2GB
SDRAM. This is because we only map the first 2GB on such systems, and therefore
the ECC parity byte of the remaining area can't be written.
This patch makes SPARC targets build again. It is caused by
phys_addr_t and phys_size_t being defined in the wrong header
file. include/lmb.h need those typedefs to build.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Scott Wood [Wed, 9 Jul 2008 22:47:52 +0000 (17:47 -0500)]
NAND: ifdef-protect most of nand.h when using legacy NAND.
Some macros such as NAND_CTL_SETALE conflict between current and legacy
NAND, being defined by the subsystem in the former case and the board
config file in the latter.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Kumar Gala [Mon, 7 Jul 2008 14:39:06 +0000 (09:39 -0500)]
Fix compiler warnings
gcc-4.3.x generates the following:
bootm.c: In function 'do_bootm_linux':
bootm.c:208: warning: cast from pointer to integer of different size
bootm.c:215: warning: cast from pointer to integer of different size
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Harald Welte [Mon, 7 Jul 2008 07:40:39 +0000 (15:40 +0800)]
Remove code duplication for setting the default environment
common/env_common.c (default_env): new function that resets the environment to
the default value
common/env_common.c (env_relocate): use default_env instead of own copy
common/env_nand.c (env_relocate_spec): use default_env instead of own copy
include/environment.h: added default_env prototype
Signed-off-by: Werner Almesberger <werner@openmoko.org> Signed-off-by: Harald Welte <laforge@openmoko.org>
Marcel Ziswiler [Sun, 22 Jun 2008 14:13:46 +0000 (16:13 +0200)]
NAND: Fix warning due to missing env_ptr casts to u_char * in env_nand.c.
The writeenv() and readenv() calls introduced by the recently added bad block
management for environment variables were missing casts therefore producing
compile time warnings.
While at it fixing some typo in a comment and indentation.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Scott Wood [Fri, 20 Jun 2008 17:38:57 +0000 (12:38 -0500)]
NAND: Rename DEBUG to MTDDEBUG to avoid namespace pollution.
This is particularly problematic now that non-NAND-specific code is
including <nand.h>, and thus all debugging code is being compiled
regardless of whether it was requested, as reported by Scott McNutt
<smcnutt@psyent.com>.
Signed-off-by: Scott Wood <scottwood@freescale.com>
avr32: Use CONFIG_ATMEL_MCI to select the atmel_mci driver
After we move the atmel_mci driver into drivers/mmc, we can't select
it with CONFIG_MMC anymore. Introduce a new symbol specifically for
this driver so that there's no ambiguity.
Andrew Klossner [Mon, 7 Jul 2008 13:41:14 +0000 (06:41 -0700)]
Fix printf errors.
The compiler will help find mismatches between printf formats and
arguments if you let it. This patch adds the necessary attributes to
declarations in include/common.h, then begins to correct the resulting
compiler warnings. Some of these were bugs, e.g., "$d" instead of
"%d" and incorrect arguments. Others were just annoying, like
int-long mismatches on a system where both are 32 bits. It's worth
fixing the annoying errors to catch the real ones.
Signed-off-by: Andrew Klossner <andrew@cesa.opbu.xerox.com>
Stefan Roese [Tue, 8 Jul 2008 10:57:14 +0000 (12:57 +0200)]
jedec_flash: Fix AM29DL800BB device ID
As pointed out by Jerry Hicks, this patch corrects the device ID of
the Spansion AM29DL800BB NOR device. Verified against latest Spansion
datasheet (rev C4 from Dezember 2006).
By Cleanup out-or-tree building for some boards (.depend)
(commit:c8a3b109f07f02342d097b30908965f7261d9f15)
because filse ware changed, some SH-boards have compile error.
I revised this problem.
Jason Jin [Tue, 13 May 2008 03:50:36 +0000 (11:50 +0800)]
Feed the watchdog in u-boot for 8610 board.
The watchdog on 8610 board is enabled by setting sw[6]
to on. Once enabled, the watchdog can not be disabled
by software. So feed the dog in u-boot is necessary for
normal operation.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Ben Warren [Tue, 24 Jun 2008 05:57:27 +0000 (22:57 -0700)]
Add mechanisms for CPU and board-specific Ethernet initialization
This patch is the first step in cleaning up net/eth.c, by moving Ethernet
initialization to CPU or board-specific code. Initial implementation is
only on the Freescale TSEC controller, but others will be added soon.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Patrice Vilchez [Tue, 27 May 2008 09:15:29 +0000 (11:15 +0200)]
[AT91SAM9] Fix NAND FLASH timings
Fix NAND FLASH timings for at91sam9x evaluation kits.
New timings are based on application note
"NAND Flash Support on AT91SAM9 Microcontrollers" available at
http://atmel.com/dyn/resources/prod_documents/doc6255.pdf
Stelian Pop [Wed, 21 May 2008 22:15:40 +0000 (00:15 +0200)]
Fix boot from NOR due to incorrect reset delay.
AT91 RSTC registers are battery-backuped, so their values
are not reset across power cycles. One of those registers,
the AT91_RSTC_MR register, is being modified by U-Boot, in
the ethernet initialisation routine, to generate a 500ms
user reset.
Unfortunately, this value is not being restored afterwards,
causing subsequent resets to also last for 500ms.
This long reset sequence causes problems (at least) in the
boot sequence from NOR: by the time the CPU tries to load
a program from the NOR flash, the latter is still in reset
and not yet available.
Additionaly, this patch fixes a bug in the original code which
caused the reset delay to last for 2s instead of 500ms.
Signed-off-by: Stelian Pop <stelian@popies.net> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
projects / u-boot / log