Jens Kuske [Fri, 19 Aug 2016 11:40:46 +0000 (13:40 +0200)]
sunxi: Tune H3 DRAM PLL to improve lock time
The H3 PLL5 used for DRAM barely manages to lock to the required
frequency before DRAM controller starts, sometimes leading to wrong
delay-line calibration results.
This patch changes the PLL tuning parameters to the same values as
boot0 used, which speeds up the locking and fixes the problem.
Signed-off-by: Jens Kuske <jenskuske@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Fri, 19 Aug 2016 13:25:41 +0000 (15:25 +0200)]
sunxi: display: Use PWM to drive backlight where applicable
When the backlight's pwm input is connected to a pwm output of the SoC,
actually use pwm to drive the backlight.
The mean reason for doing this is to fix the backlight turning off
for aprox. 1 second while the kernel is booting. This is caused by
the kernel actually using pwm to drive the backlight, so that it
can dim the backlight. First the pwm driver loads and switches the
pinmux for the pin driving the backlight's pwm input to the pwm
controller. Then about 1s later the actual backlight driver loads
and tells the pwm driver to actually update the pwm settings, which
have a power-on-reset value of "off".
An additional advantage is that this allows us to initatiate the
backlight at 80%, which is the kernel default, avoiding a brightness
change while the kernel loads.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed by: Peter Korsgaard <peter@korsgaard.com>
Hans de Goede [Fri, 19 Aug 2016 10:21:49 +0000 (12:21 +0200)]
sun5i: Add defconfig and dts file for the Empire Electronix M712 tablet
Add a defconfig and dts file for the Empire Electronix M712 tablet, this
is a 7" A13 tablet, with micro-usb (otg), headphone and micro-sd slots on
the outside. It uses a Goodix gt811 touchscreen controller, a RTL8188CTV
wifi chip and a DMART06 (1238a4) accelerometer.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Thu, 18 Aug 2016 18:51:12 +0000 (20:51 +0200)]
sunxi: Sync dts files with upstream kernel
Sync dts files with the current (Aug 18th 2016) state of Maxime's
linux/sunxi/for-next repo.
Note this commit also updates configs/MSI_Primo81_defconfig,
adding: "# CONFIG_REQUIRE_SERIAL_CONSOLE is not set", this is necessary
because the tablet does not have a reachable uart so the dts sync
drops its serial0 alias.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Thu, 18 Aug 2016 17:50:42 +0000 (19:50 +0200)]
sun6i: Add defconfig and dts file for tablets using the inet-q972 PCB
Add a defconfig and dts file for tablets using the generic inet-q972 PCB.
Tablets with this PCB feature a mini-hdmi output, micro-usb usb-host,
micro-usb usb-otg, 3.5mm headphone jack, a micro sd slot,
(mini) power-barrel and an usb wifi module.
This has been tested on a 9.7" 1024x768 qware qw tb9718-qhd tablet.
The dts files are identical to the ones submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Simon Baatz [Wed, 10 Aug 2016 08:15:42 +0000 (10:15 +0200)]
tools: kwboot: patch destaddr only for SoCs with header version 1
Commit f4db6c976cf ("arm: mvebu: Add runtime detection of UART (xmodem)
boot-mode") added a change to hdr->destaddr when dynamically patching an
image for UART boot mode. With this change, kwboot ceases to work on
Kirkwood.
Thus, let's change hdr->destaddr only when we are patching an image with
header version 1 (Orion and Kirkwood use header version 0).
Signed-off-by: Simon Baatz <gmbnomis@gmail.com> Fixes: f4db6c976cf ("arm: mvebu: Add runtime detection of UART (xmodem) boot-mode") Cc: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Kevin Smith <kevin.smith@elecsyscorp.com> Signed-off-by: Stefan Roese <sr@denx.de>
Chris Packham [Mon, 22 Aug 2016 08:52:49 +0000 (20:52 +1200)]
arm: mvebu: a38x: update serdes error handling
Ensure appropriate error messages are generated. Previously all errors
indicated that the serdes was already in use. Now appropriate error
messages are given.
Signed-off-by: Chris Packham <judge.packham@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
Chris Packham [Mon, 22 Aug 2016 00:38:39 +0000 (12:38 +1200)]
arm: mvebu: Add support for NAND interface on A-38x
The NAND interface on the Armada-38x series is similar to that on the
Armada-XP. The key difference is that the NAND ECC clock ratio is
provided via the DFX Server registers instead of the Core Clock.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Dirk Eibach <eibach@gdsys.de> Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Thu, 25 Aug 2016 13:20:01 +0000 (15:20 +0200)]
i2c: mvtwsi: Fix order of address bytes (high to low)
Patch f8a10ed1 [i2c: mvtwsi: Make address length variable] accidentally
inverted the sequence of address bytes sent to the I2C device. This
patch corrects this by sending the highest byte first and the lowest
byte last again.
Tested on theadorable Armada-XP board.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Mario Six <mario.six@gdsys.cc> Cc: Heiko Schocher <hs@denx.de>
Stephen Warren [Thu, 18 Aug 2016 16:53:33 +0000 (10:53 -0600)]
spi: tegra: fix hang in set_mode()
In tegra20_slink.c, the set_mode() function may be executed before the
SPI bus is claimed the first time, and hence the clocks to the SPI
controller may not be running. If so, any register read/write at this
time will hang the CPU. Fix this by ensuring the clock is running as soon
as the driver is probed. This is observed on the Tegra30 Beaver board.
Apply the same clock initialization fix to all other Tegra SPI drivers so
that if set_mode() is ever implemented there, the same bug will not appear.
Note that tegra114_spi.c already operates in this fashion.
The clock manipulation code is copied from claim_bus() to probe() rather
than moved. This ensures that any calls to set_speed() take effect; the
clock can't be set once during probe and left unchanged.
Fixes: 5cb1b7b395c0 ("spi: tegra20: Add support for mode selection") Cc: Mirza Krak <mirza.krak@hostmobility.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Mon, 22 Aug 2016 22:46:55 +0000 (16:46 -0600)]
ARM: tegra: remove stale nvidia, bpmp I2C DT property
The nvidia,bpmp property is left over from an old BPMP I2C binding, and
shouldn't be present. Remove it from the SoC DT file, and update the
I2C driver not to parse it; the value wasn't used for anything any more
anyway.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Thu, 18 Aug 2016 17:08:44 +0000 (11:08 -0600)]
ARM: tegra: fix Tegra186 SDHCI clock/reset names
The Tegra SDHCI binding dictates that the reseet name for the Tegra SDHCI
clock be "sdhci" not "sdmmc", and that the clock is accessed by index
rather than by name. Fix the Tegra186 DT and MMC driver to honor this.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Tom Rini [Mon, 22 Aug 2016 23:37:56 +0000 (19:37 -0400)]
fs-test.sh: Correct check_md5() test with newlines
The fs-test.sh script expected there to be a \n\r style newline at the
end of the output. This is no longer the case, so use 'tr' to remove the
\r that we get.
Fixes: (c5917b4b054d "dm: serial-uclass: Move a carriage return before a
line feed") Signed-off-by: Tom Rini <trini@konsulko.com>
Dongpo Li [Mon, 22 Aug 2016 13:03:29 +0000 (21:03 +0800)]
net: mii: check phy advertising register when geting link status
When phy autoneg on, the link speed and duplex should be
determined by phy advertising register and
phy link partner ability register.
Check phy advertising register when geting phy link speed and
duplex if autoneg on.
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
karl beldan [Sat, 20 Aug 2016 08:56:53 +0000 (08:56 +0000)]
net: davinci_emac: Restore the internal MDIO accessors return values
The spatch series converting legacy drivers from miiphy_register to
mdio_register changed the return convention of the davinci_emac internal
MDIO accessors, making the internal code relying on it misbehaving:
no mdiodev get registered and U-Boot crashes when using net cmds in the
context of the old legacy net API.
ATM davinci_emac_initialize and cpu_eth_init don't return a proper value
in that case but fixing them would not avoid the crash.
This change is just a follow-up to the spatch pass, the MDIO accessors
of the mdiodev introduced by the spatch pass retain their proper values.
Signed-off-by: Karl Beldan <karl.beldan+oss@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
karl beldan [Mon, 15 Aug 2016 17:23:01 +0000 (17:23 +0000)]
net: davinci_emac: Invalidate only the received portion of a buffer
ATM when receiving a packet the whole buffer is invalidated, this change
optimizes this behaviour.
Signed-off-by: Karl Beldan <karl.beldan+oss@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
karl beldan [Mon, 15 Aug 2016 17:23:00 +0000 (17:23 +0000)]
net: davinci_emac: Round up top tx buffer boundaries for dcache ops
check_cache_range() warns that the top boundaries are not properly
aligned when flushing or invalidating the buffers and make these
operations fail.
This gets rid of the remaining warnings:
CACHE: Misaligned operation at range
Signed-off-by: Karl Beldan <karl.beldan+oss@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
karl beldan [Sun, 14 Aug 2016 15:03:15 +0000 (15:03 +0000)]
net: davinci_emac: Remove useless dcache ops on descriptors
ATM the rx and tx descriptors are handled as cached memory while they
lie in a dedicated RAM of the SoCs, which is an uncached area.
Removing the said dcache ops, while optimizing the logic and clarifying
the code, also gets rid of most of the check_cache_range() incurred
warnings:
CACHE: Misaligned operation at range
Signed-off-by: Karl Beldan <karl.beldan+oss@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Mon, 15 Aug 2016 20:03:26 +0000 (15:03 -0500)]
net: nfs: Use the tx buffer to construct rpc msgs
Instead of always allocating a huge temporary buffer on the stack and
then memcpy()ing the result into the transmit buffer, simply figure out
where in the transmit buffer the bytes will belong and write them there
directly as each message is built.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Mon, 15 Aug 2016 20:03:25 +0000 (15:03 -0500)]
net: nfs: Move some prints to debug statements
Much of the information is verbose and derived directly from the
environment. Only output in debug mode. This also saves about 300 bytes
from the code size.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
This patch enables NFSv3 support.
If NFSv2 is available use it as usual.
If NFSv2 is not available, but NFSv3 is available, use NFSv3.
If NFSv2 and NFSv3 are not available, print an error message since NFSv4 is not supported.
Tested on iMX6 sabrelite with 4 Linux NFS servers:
* NFSv2 + NFSv3 + NFSv4 server: use NFSv2 protocol
* NFSv2 + NFSv3 server: use NFSv2 protocol
* NFSv3 + NFSv4 server: use NFSv3 protocol
* NFSv3 server: use NFSv3 protocol
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr> Cc: Tom Rini <trini@konsulko.com> Cc: joe.hershberger@ni.com Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Mon, 15 Aug 2016 19:42:16 +0000 (14:42 -0500)]
net: nfs: Remove separate buffer for default name
There is no reason to store the default filename in a separate buffer
only to immediately copy it to the main name buffer. Just write it there
directly and remove the other buffer.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Alexander Graf [Thu, 18 Aug 2016 21:45:18 +0000 (23:45 +0200)]
efi_loader: Fix relocations above 64kb image size
We were truncating the image offset within the target image to 16 bits
which again meant that we were potentially overwriting random memory
in the lower 16 bits of the image.
This patch casts the offset to a more reasonable 32bits.
With this applied, I can successfully see Shell.efi assert because it
can't find a protocol it expects to be available.
Andreas Fenkart [Wed, 17 Aug 2016 21:41:53 +0000 (23:41 +0200)]
tools/env: return with error if redundant environments have unequal size
For double buffering to work, the target buffer must always be big
enough to hold all data. This can only be ensured if buffers are of
equal size, otherwise one must be smaller and we risk data loss
when copying from the bigger to the smaller buffer.
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Lokesh Vutla [Wed, 17 Aug 2016 10:55:36 +0000 (16:25 +0530)]
ARM: OMAP4+: vcores: Remove duplicated code
There is no reason to duplicate code for DRA7xx platforms as there
can be Rail grouping. The maximum voltage detection algorithm can still
be run on other platforms with no Rail grouping and does not harm as
it gives the same result.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Lokesh Vutla [Wed, 17 Aug 2016 10:55:35 +0000 (16:25 +0530)]
ARM: OMAP5+: vcores: Drop unnecessary #ifndefs
gpio_en field is introduced to detect if pmic is controlled by GPIO.
Make this field 0 on all TPS659* pmics available on DRA7/OMAP5 based platforms
and remove the #ifndefs.
Stephen Warren [Wed, 17 Aug 2016 01:58:59 +0000 (19:58 -0600)]
test/py: match prompt only at line boundaries
This prevents capture of command output from terminating early on boards
that use a simple prompt (e.g. "=> ") that appears in the middle of
command output (e.g. crc32's "... ==> 2fa737e0").
Reported-by: Tom Rini <trini@konsulko.com> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Tested-by: Tom Rini <trini@konsulko.com> Reviewed-by: Heiko Schocher <hs@denx.de>
James Byrne [Tue, 16 Aug 2016 17:16:28 +0000 (18:16 +0100)]
common: cli_readline: Improve command line editing
This improves the cread_line() function so that it will correctly
process the 'Home', 'End', 'Delete' and arrow key escape sequences
produced by various terminal emulators. This makes command line editing
a more pleasant experience.
The previous code only supported the cursor keys and the 'Home' key, and
only for certain terminal emulator configurations. This adds support for
the 'End and 'Delete' keys, and recognises a wider range of escape
sequences. For example, the left arrow key can be 'ESC O D' instead of
'ESC [ D', and the 'Home' key can be 'ESC [ H', 'ESC O H', 'ESC 1 ~' or
'ESC 7 ~', depending on what terminal emulator you use and how it is
configured.
Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Changes for v2
- Explicitly initialize variable to avoid spurious compiler warning.
Changes for v3
- Remove unnecessary setting of 'act' to ESC_REJECT (now its default
value).
Tom Rini [Fri, 12 Aug 2016 12:31:17 +0000 (08:31 -0400)]
Kconfig: DISTRO_DEFAULTS: Only enable CMD_BOOTZ for ARM
The 'bootz' command is really only for ARM32 Linux Kernel 'zImage' files
but has also been adapted for testing with sandbox. Given that sandbox
is a test platform, don't add that logic under DISTRO_DEFAULTS.
Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Fri, 12 Aug 2016 12:31:15 +0000 (08:31 -0400)]
cmd: Split 'bootz' and 'booti' out from 'bootm'
The bootz and booti commands rely on common functionality that is found
in common/bootm.c and common/bootm_os.c. They do not however rely on
the rest of cmd/bootm.c to be implemented so split them into their own
files. Have various Makefiles include the required infrastructure for
CONFIG_CMD_BOOT[IZ] as well as CONFIG_CMD_BOOTM. Move the declaration
of 'images' over to common/bootm.c.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Maxime Ripard [Tue, 5 Jul 2016 08:26:45 +0000 (10:26 +0200)]
cmd: fdt: add fdt overlay application subcommand
The device tree overlays are a good way to deal with user-modifyable
boards or boards with some kind of an expansion mechanism where we can
easily plug new board in (like the BBB or the raspberry pi).
However, so far, the usual mechanism to deal with it was to have in Linux
some driver detecting the expansion boards plugged in and then request
these overlays using the firmware interface.
That works in most cases, but in some cases, you might want to have the
overlays applied before the userspace comes in. Either because the new
board requires some kind of an early initialization, or because your root
filesystem is accessed through that expansion board.
The easiest solution in such a case is to simply have the component before
Linux applying that overlay, removing all these drawbacks.
Reviewed-by: Stefan Agner <stefan@agner.ch> Acked-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 5 Jul 2016 08:26:44 +0000 (10:26 +0200)]
libfdt: Add overlay application function
The device tree overlays are a good way to deal with user-modifyable
boards or boards with some kind of an expansion mechanism where we can
easily plug new board in (like the BBB, the Raspberry Pi or the CHIP).
Add a new function to merge overlays with a base device tree.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 5 Jul 2016 08:26:38 +0000 (10:26 +0200)]
libfdt: Add iterator over properties
Implement a macro based on fdt_first_property_offset and
fdt_next_property_offset that provides a convenience to iterate over all
the properties of a given node.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Simon Glass <sjg@chromium.org>
Maxime Ripard [Tue, 5 Jul 2016 08:26:35 +0000 (10:26 +0200)]
scripts: Makefile.lib: Sanitize DTB names
Having dashes as a separator in the DTB name is a quite common practice.
However, the current code to generate objects from DTBs assumes the
separator is an underscore, leading to a compilation error when building a
device tree with dashes.
Replace all the dashes in the DTB name to generate the symbols name, which
should solve this issue.
Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Stefan Roese [Mon, 15 Aug 2016 11:50:59 +0000 (13:50 +0200)]
x86: Add theadorable-x86-dfi-bt700 board support
This patch adds support for the BayTrail based theadorable-x86-dfi-bt700
board which uses the DFI BT700 BayTrail Qseven SoM on a custom baseboard.
The main difference to the DFI baseboard is, that it isn't equipped
with a Super IO chip and uses the internal HS SIO UART (memory mapped
PCI based) as the console UART.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Stefan Roese [Mon, 15 Aug 2016 11:50:49 +0000 (13:50 +0200)]
x86: Add DFI BT700 BayTrail board support
This patch adds support for the DFI BayTrail BT700 QSeven SoM installed
on the DFI Q7X-151 baseboard. The baseboard is equipped with the Nuvoton
NCT6102D Super IO chip providing the UART as console.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Stefan Roese [Tue, 28 Jun 2016 13:45:13 +0000 (15:45 +0200)]
x86: conga-qeval20-qa3: Add SMBus support and SMSC2513 config code
This patch includes the following changes:
- Remove Designware I2C support from dts as its not used
- Configure SMBus PADs in dts
- Enable I2C commands and I2C support
- Configure SMSC2513 USB hub via SMBus upon startup
- Move environment location to match Minnowmax example
- Enhancement of the default environment
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds support for the SMBus block read/write functionality.
Other protocols like the SMBus quick command need to get added
if this is needed.
This patch also removed the SMBus related defines from the Ivybridge
pch.h header. As they are integrated in this driver and should be
used from here. This change is added in this patch to avoid compile
breakage to keep the source git bisectable.
Tested on a congatec BayTrail board to configure the SMSC2513 USB
hub.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Simon Glass <sjg@chromium.org> Cc: Heiko Schocher <hs@denx.de> Cc: George McCollister <george.mccollister@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Yaroslav K [Tue, 9 Aug 2016 03:32:15 +0000 (20:32 -0700)]
cbfs: Fix incorrect CBFS file header size being used
This fixes incorrect filenames in cbfsls output.
Signed-off-by: Yaroslav K. <yar444@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
[clean up checkpatch errors and warnings] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Bin Meng [Tue, 2 Aug 2016 03:53:53 +0000 (20:53 -0700)]
x86: bayleybay: Add PS/2 keyboard and mouse to ASL file
Without PS/2 keyboard and mouse in the ASL file, Windows does not
see them. No problem for Linux as it probes keyboard and mouse via
the legacy 8042 I/O port.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Explicitly enable ILB_SERIRQ function 1 in
cfio_regs_pad_ilb_serirq_PCONF0.
Pad configuration for SERIRQ is not set to enable the SERIRQ function
after a reset though strangely, it is on initial boot.
Rebooting from Linux, reset command in u-boot and even pushing the reset
button on the development board all lead to the SERIRQ function being
disabled (address 0xfed0c560 with value of 0x2003cc80).
Signed-off-by: George McCollister <george.mccollister@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Stefan Roese [Tue, 19 Jul 2016 05:45:46 +0000 (07:45 +0200)]
misc: Add simple driver for some Nuvoton NCT6102D devices
This simple driver provides some functions to control some of the
integrated devices. The watchdog is enabled per default. This driver
adds a function to disable the watchdog. Also the internal legacy
UART (io address 0x3f8/0x2f8) is enabled per default.
Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Cc: Simon Glass <sjg@chromium.org>
Stefan Roese [Tue, 19 Jul 2016 05:41:25 +0000 (07:41 +0200)]
x86: baytrail: Add SIO HS-UART clock setup
To support the BayTrail internal SIO HS UART, the internal UART clock
needs to get configured. This patch adds support for this clock
configuration which will be done, if the PCI device(s) are found.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Stefan Roese [Mon, 18 Jul 2016 10:53:31 +0000 (12:53 +0200)]
x86: cache.h: Add default for CONFIG_SYS_CACHELINE_SIZE
Don't just define ARCH_DMA_MINALIGN but also CONFIG_SYS_CACHELINE_SIZE
if it's undefined. This is needed for the xhci driver to compile.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
projects / u-boot / log