Wolfgang Denk [Sun, 25 Sep 2005 22:29:53 +0000 (00:29 +0200)]
Fixes to the Lubbock (PXA 25x) support:
- Resolve the FIXME with respect to saving the u-boot environment.
- Make the default load address land in real memory.
- Fix lan91c96 SMC_{in,out}{b,w,l}() macros
Patch by David Brownell, 10 Mar 2005
Wolfgang Denk [Sun, 25 Sep 2005 16:41:04 +0000 (18:41 +0200)]
OMAP242x H4 board update
- fix for ES2 differences.
- switch to using the cfi_flash driver.
- fix SRAM build address.
- fix for GP device operation.
- unlock SRAM for GP devices.
- display more device information.
- fix potential deadlock in omap24xx_i2c driver.
- fix DLL load values to match dpllout*1 operation.
- fix 2nd chip select init for combo DDR device.
- add support for CFI Intel 28F256L18 on H4 board.
Patch by Richard Woodruff, 03 Mar 2005
Wolfgang Denk [Sun, 25 Sep 2005 14:50:33 +0000 (16:50 +0200)]
Fix au1x00_serial baud rate calculation:
remove hardcoded cpu clock divisor and use register instead;
round up instead of truncate
Patch by Andrew Dyer, 15 Feb 2005
Wolfgang Denk [Sat, 24 Sep 2005 22:59:24 +0000 (00:59 +0200)]
OMAP242x fix for GP device booting
- Add SRAM unlock for GP devices.
- Change DDR DLL unlock value to allow DPLLout*1 operation.
Patches by Richard Woodruff, 21 Jan 2005:
Wolfgang Denk [Sat, 24 Sep 2005 22:53:22 +0000 (00:53 +0200)]
Add support for AMD's Pb1x00 eval board;
add MII routines to the au1x00 ethernet driver;
add USB ohci driver (work in progress)
Patch by Thomas Sailer, 20 Jan 2005
Wolfgang Denk [Sat, 24 Sep 2005 22:23:05 +0000 (00:23 +0200)]
Update omap5912osk board:
Use drivers/cfi_flash.c instead of private flash driver;
Remove hardcoded personalized settings from omap5912osk.h;
Fix spacing with (RO) marks in 'flinfo' output.
Patch by Michael Bendzick, 14 Jan 2005
Wolfgang Denk [Sat, 24 Sep 2005 21:41:00 +0000 (23:41 +0200)]
virtex2 fix for bogus download error messages
The virtex2 FPGA download code watches for init going active during
a download of config data as an error condition. init also goes
active after a configuration is finished in concert with the done
signal. So far, the code does not check for done active until all
of the configuration data is sent. If configuration data has a few
extra pad bytes at the end, this would cause an error message even
though the download had suceeded.
NOTE: virtex2 slave serial and spartan2 versions may still have the
same problem.
Patch by Andrew Dyer, 12 Jan 2005
Wolfgang Denk [Sat, 24 Sep 2005 21:32:48 +0000 (23:32 +0200)]
Optimize flash_make_cmd in drivers/cfi_flash.c for little endian
Fix "WARNING: flash_make_cmd: unsuppported LittleEndian mode"
message when probing for nonexistent flash in little endian mode.
As a side effect more efficient and smaller code is generated,
which is always a Good Thing (TM).
Patch by Ladislav Michl, 24 Sep 2005
Wolfgang Denk [Sat, 24 Sep 2005 21:25:46 +0000 (23:25 +0200)]
Update for TFTP using a fixed UDP port
Use the approved environment variable names. Added "tftpdstp" to
allow ports other than 69 per Tolunay Orkun's recommendation.
Patch by Jerry Van Baren, 12 Jan 2005
Wolfgang Denk [Sat, 24 Sep 2005 20:37:32 +0000 (22:37 +0200)]
Allow to force TFTP to use a fixed UDP port
(Add a configuration option CONFIG_TFTP_PORT and optional env variable tftpport)
Patch by Jerry Van Baren, 10 Jan 2005
Stefan Roese [Thu, 22 Sep 2005 07:04:17 +0000 (09:04 +0200)]
Add SM501 support to HH405 board.
Add support for gzip compressed bmp's (CONFIG_VIDEO_BMP_GZIP).
Add support for eeprom write-enable (CFG_EEPROM_WREN).
Patch by Stefan Roese, 22 Sep 2005
Stefan Roese [Thu, 15 Sep 2005 09:34:07 +0000 (11:34 +0200)]
Update AMCC Yosemite to get a consistent setup for all AMCC eval
boards (baudrate, environment...). Flash driver fixed.
Patch by Stefan Roese, 15 Sep 2005
Stefan Roese [Wed, 31 Aug 2005 10:55:50 +0000 (12:55 +0200)]
Add I2C support to TQM8540 and TQM8560 boards (EEPROM, RTC, LM75-DTT).
Removed CFG_CMD_DISPLAY from default commands.
Fixed compiler warning in net.c.
Patch by Stefan Roese, 31 Aug 2005
Wolfgang Denk [Wed, 31 Aug 2005 10:28:00 +0000 (12:28 +0200)]
Fix problems with ld version 2.16 (dot outside sections problem)
Pointed out by Gerhard Jaeger, 31 Aug 2005;
cf. http://sourceware.org/ml/binutils/2005-08/msg00412.html
Wolfgang Denk [Tue, 30 Aug 2005 12:13:23 +0000 (14:13 +0200)]
Prepare U-Boot for gcc-4.x: fix global data pointer initialization
The global data pointer, stored in r29 before relocation to RAM, was
not initialized to a correct value. This happened because the pointer
declaration was done locally in the scope of the board_init_f()
function. What follows is a cite from gcc.info, 5.37, "Variables in
Specified Registers":
...
The compiler's data flow analysis is capable of determining where
the specified registers contain live values, and where they are
available for other uses. Stores into local register variables
may be deleted when they appear to be dead according to dataflow
analysis. References to local register variables may be deleted
or moved or simplified.
...
Moving the global data declaration to global scope solved the
problem.
Wolfgang Denk [Thu, 18 Aug 2005 23:05:06 +0000 (01:05 +0200)]
Fix MPC52xx watchdog driver
- make watchdog driver work on systems with an IPB clock
frequency of 133 MHz (watchdog expired to fast there).
- now all three watchdog chain entries could be used.
- fix some typos.
Patch by Martin Krause, 23 Jun 2005
Wolfgang Denk [Thu, 18 Aug 2005 22:46:54 +0000 (00:46 +0200)]
Add new board specific commands for TQM5200/STK52XX
- Sound commands (beep, wav, sound)
- Test commands (led, can, backlight, rs232)
Patch by Martin Krause, 02 May 2005
projects / u-boot / log