Giuseppe Pagano [Fri, 15 Nov 2013 16:42:54 +0000 (17:42 +0100)]
udoo: Fix watchdog during kernel boot.
uDoo uses APX823-31W5 watchdog chip. Timeout is about 1.2 seconds.
To disabled watchdog during kernel boot, WDI pin of that chip needs to be
in "high impedance" state. I.mx6 gpio configuration does not contemplate
tristate, so pin is set as input in high impedance.
Giuseppe Pagano [Fri, 15 Nov 2013 16:42:50 +0000 (17:42 +0100)]
udoo: Move and optimize platform register setting.
Previous uDoo configuration adopts register settings for DDR3, clock, muxing,
etc. taken from Nitrogen6x. uDoo schematics is rather different from that board,
and it needs customized setting for most of the registers.
All this changes can be considered atomical since it is part of initial support
of the board.
Patch changes uDoo configuration files path to a specific one, and adopt
optimized value for every configured register.
Marek Vasut [Sat, 12 Oct 2013 18:36:25 +0000 (20:36 +0200)]
Net: FEC: Fix huge memory leak
The fec_halt() never free'd both RX and TX DMA descriptors that
were allocated in fec_init(), nor did it free the RX buffers.
Rework the FEC driver so that these descriptors and buffers are
allocated only once in fec_probe().
Fabio Estevam [Fri, 1 Nov 2013 10:12:24 +0000 (08:12 -0200)]
configs: imx: Make CONFIG_SYS_PROMPT uniform across FSL boards
There is no real benefit in adding the board name into U-boot's prompt, so
remove the custom CONFIG_SYS_PROMPT definitions so that the standard "=> "
prompt is used across FSL boards.
Samuel Egli [Mon, 4 Nov 2013 13:05:03 +0000 (14:05 +0100)]
arm, am335x: update for the siemens boards
- dxr2: define unused pins as input
- do not enable RTC32K OSC on dxr2 board
- update default environment
- add splashpos=m,m to default environment, so splash screen is always
centered.
- adapt environment for bootcount feature
- add altbootcmd to default environment
- rut: SPL add early reset pulse for eth-phy, maXTouch and display
- rut: display timing aenderungen
- siemens boards: adapt for background color = white
- add boutcount feature for the siemens boards
store the bootcount in the environment, as we have no softreset
save registers on this hardware. Use therefore the CONFIG_BOOTCOUNT_ENV
bootcount driver.
- change spi mode from 3 to 0 for the lcd init
- add gpio pin for lcd reset with state 0 and add mdelay
- siemens boards: use own USB id's
- add dfu serial and device number for siemens boards
Add for the siemens boards the possibility to define in dfu mode,
the iSerialNumber and the bcdDevice fields in the USB Device
descriptor.
- fix upgrade mechanism based on bootcount
Correct location of saveenv and remove not active variable.
Add CONFIG_BOOT_RETRY_TIME and CONFIG_RESET_TO_RETRY to
reboot board in case of empty kernel partition. Without
these defines an empty kernel partition leads to an
abort of boot process and one remains in u-boot prompt.
- general cleanup of dxr2, pxm2 and rut boards
all:
* Remove net boot from bootcmd
Ping can cause a crash on boards without ethernet phy.
net_nfs command is used only for development
* Add reset at the end of bootcmd
In order to have an immediate reset of the boot when bootcmd
fails, add reset at the end of bootcmd.
rut:
* add nand_img_size
dxr2:
* update nand_img_size
* ddr3 timings updated with iocontrol property that can be
modified via eeprom. New default parameters from software
leveling with draco ES2.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com> Signed-off-by: Pascal Bach <pascal.bach@siemens.com> Signed-off-by: Roger Meier <r.meier@siemens.com> Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Matthias Michel <matthias.michel@siemens.com> Cc: Tom Rini <trini@ti.com>
Heiko Schocher [Mon, 4 Nov 2013 13:05:02 +0000 (14:05 +0100)]
usb, g_dnl: make bcdDevice value configurable
add the possibility to set the bcdDevice number board specific.
Therefore the weak function g_dnl_get_board_bcd_device_number()
is introduced. Used on the siemens boards.
Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Kyungmin Park <kyungmin.park@samsung.com>
Tom Rini [Fri, 8 Nov 2013 18:53:14 +0000 (13:53 -0500)]
am33xx: Make SoC bootcount driver have its own symbol
Some am33xx boards may not use the RTC block for bootcount (as it may
not be wired up for the board) and use some other facility. So add
another symbol for the bootcount driver for the IP block.
Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
Andrew Bradford [Mon, 4 Nov 2013 20:42:52 +0000 (15:42 -0500)]
am335x_evm: Fix CONS_INDEX numbering
Commit f6d1f6e4a58edae4776937647381a43fea5e83a5 broke selection of UARTs
other than UART0 for am335x_evm configurations by setting CONS_INDEX to
1 for all configurations. Revert the CONS_INDEX changes.
Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
Heiko Schocher [Mon, 4 Nov 2013 13:05:00 +0000 (14:05 +0100)]
arm, am33x: make RTC32K OSC enable configurable
As
http://www.denx.de/wiki/view/U-Boot/DesignPrinciples#2_Keep_it_Fast
states:
"Initialize devices only when they are needed within U-Boot"
enable the RTC32K OSC only, if CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC is
enabled. Enable this in ti_am335x_common.h, so all boards in mainline
should work as before.
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com>
Heiko Schocher [Mon, 4 Nov 2013 13:04:59 +0000 (14:04 +0100)]
bootcount: store bootcount var in environment
If no softreset save registers are found on the hardware
"bootcount" is stored in the environment. To prevent a
saveenv on all reboots, the environment variable
"upgrade_available" is introduced. If "upgrade_available" is
0, "bootcount" is always 0 therefore no need to save the
environment on u-boot boot, if "upgrade_available" is 1 "bootcount"
is incremented in the environment and environment gets written
on u-boot start.
So the Userspace Applikation must set the "upgrade_available"
and "bootcount" variable to 0 (for example with fw_setenv),
if a boot was successfully.
Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:
include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.
include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.
Note: 'git show' will also list two files just because
they are new:
Suriyan Ramasami [Wed, 16 Oct 2013 16:54:24 +0000 (09:54 -0700)]
netconsole loses 2nd character of input
Netconsole loses the second character when used as input by
either setenv stdin nc or setenv stdin serial,nc if using CONSOLE_CONSOLE_MUX
Before a nc_send_packet() to echo the input, a check is done to see if
nc_ether is valid. If its not, it waits for an arp request and then sends
the packet (which contains the first character of line to be displayed as
output). As part of reaping the arp request, the second character is consumed.
We protect this by making the call to NetLoop(NETCONS) between
input_recursion.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Pierre Aubert [Tue, 8 Oct 2013 12:20:27 +0000 (14:20 +0200)]
env: fix the env export varname
The env export command doesn't export the first variable of the list
since commit 5a31ea04c9ee5544fbb70ad7597ea4b294840eab
"env grep" - reimplement command using hexport_r()
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
Mark Langsdorf [Tue, 10 Sep 2013 20:20:23 +0000 (15:20 -0500)]
autoboot: add an option to override keyed autoboot
As originally implemented, setting the AUTOBOOT_KEYED config option will
prevent users from breaking into the autoboot script with ctrl-c. Restore
that option with a new config symbol.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Piotr Wilczek [Fri, 11 Oct 2013 13:43:33 +0000 (15:43 +0200)]
fs:fat: fix set file name function
Curently memcpy copies string without null terminating char because
function strlen returns only number of characters excluding
null terminating character. Replace memcpy with strcpy.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> CC: Tom Rini <trini@ti.com>
Egbert Eich [Fri, 4 Oct 2013 16:53:04 +0000 (18:53 +0200)]
cmd/gpt: Support gpt command for all devices
The gpt command was only implemented for mmc devices. There is no reason
why this command should not be generalized and be applied all other
storage device classes.
This change both simplifies the implementation and eliminates a
build failure for systems that don't support mmcs.
Signed-off-by: Egbert Eich <eich@suse.com> Tested-by: Piotr Wilczek <p.wilczek@samsung.com>
[trini: Change coding style slightly] Signed-off-by: Tom Rini <trini@ti.com>
cosmetic: doc: driver-model: Do not number driver lists
Everytime a dead driver is removed from the list,
we must re-number. This is a painful task.
Try
git show e53232250 -- doc/driver-model/UDM-serial.txt
git show 6f62f4207 -- doc/driver-model/UDM-serial.txt
git show b9f4bc34a -- doc/driver-model/UDM-serial.txt
to see what I mean.
Bo Shen [Thu, 7 Nov 2013 06:29:41 +0000 (14:29 +0800)]
usb: dfu: make nand upload working
Nowhere pass a value to len, which always 0, make no transfer which
cause uploading failed.
This patch make nand upload working. However it needs enough malloc
buffer to store read data, that means the buffer at least equal to
the upload partition size, or else it doesn't work.
Heiko Schocher [Mon, 4 Nov 2013 13:05:01 +0000 (14:05 +0100)]
usb, g_dnl: make iSerialNumber board configurable
add the possibility to set the iSerialNumber board specific.
Default value for iSerialNumber is 0x0. This value can
changed board specific through the new function
g_dnl_set_serialnumber() which must be called from the
board specific function g_dnl_bind_fixup().
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Tested-by: Lukasz Majewski <l.majewski@samsung.com>
usb: ums: add ums exit feature by ctrl+c or by detach usb cable
This patch allows exiting from UMS mode to u-boot prompt
by detaching usb cable or by pressing ctrl+c.
Add new config: CONFIG_USB_CABLE_CHECK. If defined then board
file should provide function: usb_cable_connected() (include/usb.h)
that return 1 if cable is connected and 0 otherwise.
Changes v2:
- add a note to the README
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Marek Vasut <marex@denx.de>
usb: ums: move ums code from trats to Samsung common directory
UMS init was implemented in trats board file but mostly it comprises
common code. Due to that it has been moved to common/ums.c to avoid
code duplication in the future.
Changes:
- move ums initialization code from trats to common/ums.c
- remove unused CONFIG_USB_GADGET_MASS_STORAGE from trats.h
Changes v2:
- move this patch at the top of code cleanups patches
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: Minkyu Kang <mk7.kang@samsung.com>
usb: ums: fix disk capacity miscalculation and code cleanup
This patch prevents:
- ums disk capacity miscalculation because of integer overflow
Changes v2:
- Prevents passing zero size disk capacity to ums gadget driver
- Change function ums_get_capacity() to ums_disk_init() and do ums disk
initialization before gadget init
- Remove unnecessary code from mass storage driver
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Marek Vasut <marex@denx.de>
usb: ums: code refactoring to improve reusability on other boards.
This patch introduces some cleanups to ums code. Changes:
ums common:
- introduce UMS_START_SECTOR and UMS_NUM_SECTORS as defined in
usb_mass_storage.h both default values as 0 if board config
doesn't define them
common cleanup changes:
- change name of struct "ums_board_info" to "ums"
- "ums_device" fields are moved to struct ums and "dev_num" is removed
- change function name: board_ums_init to ums_init
- remove "extern" prefixes from usb_mass_storage.h
cmd_usb_mass_storage:
- change error() to printf() if need to print info message
- change return values to command_ret_t type at ums command code
- add command usage string
Changes v2:
ums common:
- always returns number of read/write sectors
- coding style clean-up
ums gadget:
- calculate amount of read/write from device returned value.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Marek Vasut <marek.vasut@gmail.com>
Igor Grinberg [Wed, 6 Nov 2013 15:24:02 +0000 (17:24 +0200)]
README: remove wrong config name
There is no CONFIG_PCA953X_INFO symbol.
U-Boot uses CONFIG_CMD_PCA953X_INFO instead, which is described in
"Monitor Functions" section and thus no need to be repeated in the
"GPIO Support" section.
Remove the whole line.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Miao Yan [Mon, 4 Nov 2013 03:18:14 +0000 (11:18 +0800)]
common/cmd_bootm.c: fix subcommand processing in OS specific do_bootm_xxx() functions
In commit "5c427e4: use BOOTM_STATE_OS_CMDLINE flag for plain bootm"
and "3d187b3: Only pass BOOTM_STATE_OS_CMDLINE on PowerPC/MIPS",
BOOTM_STATE_OS_CMDLINE was added to do_bootm for PowerPC and MIPS. This
breaks other OSes (vxworks, netbsd, plan9,...) that don't support
subcommand processing, e.g. they all contain the following code in their
do_bootm_xxx():
if (flag & BOOTM_STATE_OS_PREP)
return 0;
if ((flag != 0) && (flag != BOOTM_STATE_OS_GO))
return 1;
which will result a "subcommand not supported" error.
This patch changes the above logic to:
/* if not go command, pretend everything to be OK */
if (flag != BOOTM_STATE_OS_GO)
return 0;
Masahiro Yamada [Fri, 1 Nov 2013 01:28:45 +0000 (10:28 +0900)]
Makefile: do not create a symbolic link to arch/${ARCH}/include/asm
In-tree build:
- Do not create a symbolic link
from include/asm to arch/${ARCH}/include/asm
- Add ${SRCTREE}/arch/arm/include into the header search path
Out-of-tree build:
- Do not create a directory ${OBJTREE}/include2
- Do not create a symbolic link
from ${OBJTREE}/include2/asm to ${SRCTREE}/arch/${ARCH}/include/asm
- Add ${SRCTREE}/arch/arm/include into the header search path
Paul Burton [Wed, 23 Oct 2013 10:17:14 +0000 (11:17 +0100)]
boards.cfg: remove trailing whitespace
Commit 93e14596 "Coding Style cleanup: replace leading SPACEs by TABs"
added trailing whitespace to a single line of boards.cfg. I presume this
was unintentional, and it causes the file to change after running it
through the reformat.py script. Remove the offending character.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Andrew Ruder [Wed, 23 Oct 2013 00:07:34 +0000 (19:07 -0500)]
cmd_nvedit.c: Add env exists command
env exists is a way to test (in hush) if an environment variable
exists. A workaround existed using printenv but this new command
doesn't require all the stdout/stderr redirection to prevent
printing information to the screen.
Masahiro Yamada [Mon, 21 Oct 2013 02:11:27 +0000 (11:11 +0900)]
MAKEALL: fix boards_by_field function
Commit 27af930e changed the boards.cfg format
and it changed boards_by_field() function incorrectly.
For tegra cpus it returned Board Name field,
not Target field.
This commit restores the behavior prior to 27af930e in the right way.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Masahiro Yamada [Mon, 21 Oct 2013 02:11:26 +0000 (11:11 +0900)]
MAKEALL: fix a bug to use CROSS_COMPILE_<ARCH>
Commit 27af930e changed the boards.cfg format but
missed to change get_target_arch() fuction.
This commit adjusts it for CROSS_COMPILE_<ARCH>
to work correctly.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Roger Meier [Mon, 4 Nov 2013 06:40:44 +0000 (07:40 +0100)]
at91: add defines for reset type
Signed-off-by: Roger Meier <r.meier@siemens.com> Acked-by: Bo Shen <voice.shen@atmel.com> Reviewed-by: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
ARM: ATMEL: eb_cpux9k2: fix TEXT_BASE for ramboot target
Since more functions are enabled, the eb_cpux9k2_ram target does not boot.
This patch changed the TEXT_BASE, that the code fits between TEXT_BASE and ram end.
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Mon, 21 Oct 2013 08:14:00 +0000 (16:14 +0800)]
arm: atmel: get rid of too many ifdeffery
Get rid of too many ifdeffery in usb ohci driver
Add following two configuration for USB clock selecting
- CONFIG_USB_ATMEL_CLK_SEL_PLLB: using PLLB as usb ohci input clock
- CONFIG_USB_ATMEL_CLK_SEL_UPLL: using UPLL as usb ohci input clock
Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Rob Herring [Fri, 18 Oct 2013 18:04:42 +0000 (13:04 -0500)]
pxe: fix handling of absolute paths
pxelinux and syslinux differ in their handling of absolute paths in menu
files. A pxelinux path is aways prepended with the bootfile path while
syslinux allows for absolute paths. u-boot was always treating a leading
/ as an absolute path breaking some pxelinux setups. Fix this by adding
a flag to distinguish pxelinux vs. syslinux behavior.
Reported-by: Ian Campbell <Ian.Campbell@citrix.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com>
projects / u-boot / log