Aneesh V [Mon, 21 Nov 2011 23:33:58 +0000 (23:33 +0000)]
armv7: disable L2 cache in cleanup_before_linux()
We were not disabling external caches before jumping
to kernel. We were flushing all caches including
external caches and disabling caches globally in
CP15 System Control register. Apparently this is not
enough.
The bootstrap loader in Linux kernel that does decompression
enables data-caches again, flush them after use and disable
them before jumping to kernel proper. However, it's not aware
of the external caches.
Since we have left external cache enabled, external cache will
get used once caches are enabled globally, but it's not flushed
because decompressor is not aware of external caches. When it
jumps to kernel with caches disabled globally, we have stale
data in the external cache and a coherency problem.
This was breaking the boot for OMAP4 with latest mainline
kernel. The solution is to disable external caches in
cleanup_before_linux(). With this fix kernel is booting again.
Cc: Albert Aribaud <albert.u.boot@aribaud.net> Signed-off-by: Aneesh V <aneesh@ti.com>
Marek Vasut [Mon, 31 Oct 2011 13:17:21 +0000 (14:17 +0100)]
PXA: Adapt Voipac PXA270 to OneNAND SPL
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
V2: Add missing u-boot-spl.lds, convert bitshifts to division,
convert to spl_onenand_load_image()
Marek Vasut [Sat, 5 Nov 2011 18:26:47 +0000 (19:26 +0100)]
PXA: Re-add the Dcache locking as RAM for pxa250
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefan Herbrechtsmeier <sherbrec@cit-ec.uni-bielefeld.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Marek Vasut [Mon, 31 Oct 2011 13:12:39 +0000 (14:12 +0100)]
PXA: Rework start.S to be closer to other ARMs
The start.S on PXA was very obscure. This reworks it back to be close to arm1136
start.S and others.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
V2: Don't compile in relocation support if building SPL
Simon Schwarz [Mon, 31 Oct 2011 06:34:45 +0000 (06:34 +0000)]
Fix regression in SMDK6400
s3c64xx.c implemented its own nand_read_byte, nand_write_buf and
nand_read_buf functions. This provoked a regression when these functions
were made public by patch 55f429bb39614a16b1bacc9a8bea9ac01a60bfc8.
This deletes these duplicated functions from s3c64xx.c and adds the generic
implementations in nand_base.c to the spl Makefile. It also adds
-ffcuntion-sections and -gc-sections to the compilation flags of the SPL to
avoid errors originating from unused functions in nand_base.c.
Description of the regression:
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/108873
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> Cc: scottwood@freescale.com Cc: s-paulraj@ti.com Cc: albert.u.boot@aribaud.net
Simon Guinot [Mon, 21 Nov 2011 13:55:46 +0000 (19:25 +0530)]
mvsata: fix ide_preinit for missing disks
Consider that ide_preinit() succeed if at least one port is successfully
initialized. This allows to iniatialize IDE support on a board with two
SATA ports but a single hard disk available.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Sanjeev Premi [Wed, 16 Nov 2011 15:20:47 +0000 (10:20 -0500)]
part_efi: Fix compile errors
Fix errors noticed after enabling CONFIG_EFI_PARTITION
for the OMAP3 EVM board:
part_efi.c: In function 'print_part_efi':
part_efi.c:133:5: warning: passing argument 3 of 'is_gpt_valid'
from incompatible pointer type
part_efi.c:95:12: note: expected 'struct gpt_header *' but arg
ument is of type 'struct gpt_header **'
part_efi.c: In function 'get_partition_info_efi':
part_efi.c:173:4: warning: passing argument 3 of 'is_gpt_valid
' from incompatible pointer type
part_efi.c:95:12: note: expected 'struct gpt_header *' but arg
ument is of type 'struct gpt_header **'
part_efi.c: In function 'alloc_read_gpt_entries':
part_efi.c:384:18: error: 'CONFIG_SYS_CACHELINE_SIZE' undeclare
d (first use in this function)
Signed-off-by: Sanjeev Premi <premi@ti.com> Cc: Tom Rini <tom.rini@gmail.com> Cc: Anton staaf <robotboy@chromium.org> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
When building u-boot as 64 bit application (e.g. sandbox) ulong might be
64 bits in size. This breaks network code as IPaddr_t is 64 bytes in
size then and an IPv4 address is 32 bits in size. This patch makes sure
that IPaddr_t is always 32 bits in size. Also some warnings introduced
by this patch are fixed.
Signed-off-by: Matthias Weisser <weisserm@arcor.de> Acked-by: Mike Frysinger <vapier@gentoo.org>
Igor Grinberg [Sun, 27 Nov 2011 21:57:38 +0000 (21:57 +0000)]
tools/envcrc: fix compile breakage
When ENV_IS_EMBEDDED is not set, but CONFIG_BUILD_ENVCRC is set,
the environment.h file does not get included resulting in unrecognized
env_t type.
Fix this by moving the include directive.
Reported-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Tested-by: Mike Frysinger <vapier@gentoo.org>
Andy Fleming [Mon, 21 Nov 2011 13:40:43 +0000 (13:40 +0000)]
Add a "tidy" build option
It is sometimes desireable to clean up the byproducts of the build
process without removing the executable results. "make clean" is
close, but leaves the build directory with a large number of
*.depend* files. This new build option invokes make clean, and then
removes the depend files.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Vadim Bendebury [Sat, 15 Oct 2011 15:13:34 +0000 (15:13 +0000)]
Add a cli command to test the TPM device.
The command gets an arbitrary number of arguments (up to 30), which
are interpreted as byte values and are feed into the TPM device after
proper initialization. Then the return value and data of the TPM
driver is examined.
TPM commands are described in the TCG specification.
For instance, the following sequence is the 'TPM Startup' command, it
is processed by the TPM and a response is generated:
If the command is corrupted (fed one byte short), an error is reported:
boot > tpm 0x0 0xc1 0x0 0x0 0x0 0xc 0x0 0x0 0x0 0x99 0x0
generic_lpc_tpm.c:311 unexpected TPM status 0xff000888
generic_lpc_tpm.c:516 failed sending data to TPM
tpm command failed
boot >
Change-Id: I3f3c5bfec8b852e208c4e99ba37b0f2b875140b0 Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> CC: Wolfgang Denk <wd@denx.de>
This patch is added for PHY whose register offset value exceeds 0xFF and
cannot be used with "unsigned char" datatype in miiphy_read, miiphy_write
and miiphy_register functions. Datatype of register offset is changed to
unsigned short instead of unsigned char so that offset value greater then
0xFF can be used.
Signed-off-by: Chandan Nath <chandan.nath@ti.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
Mike Partington [Wed, 27 Oct 2010 10:31:09 +0000 (10:31 +0000)]
Standalone Apps: Standalone apps should need only exports.h.
Modify exports.h to remove its dependencies on other files, thus
enabling standalone apps to require only exports.h from the U-Boot
source tree. This appears to be the intent based on the following
note: http://lists.denx.de/pipermail/u-boot/2010-January/067174.html
Signed-off-by: Mike Partington <mparting@lexmark.com>
Fix:
flash.c: In function 'flash_erase_1':
flash.c:514:24: warning: variable 'l_sect' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'flash_erase_2':
flash.c:956:24: warning: variable 'l_sect' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de> Acked-by: Stefan Roese <sr@denx.de>
Fix:
flash.c: In function 'flash_erase_1':
flash.c:425:24: warning: variable 'l_sect' set but not used
[-Wunused-but-set-variable]
flash.c: In function 'flash_erase_2':
flash.c:834:24: warning: variable 'l_sect' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de> Acked-by: Stefan Roese <sr@denx.de>
Fix:
In file included from flash.c:45:0:
../common/flash.c: In function 'flash_erase':
../common/flash.c:399:24: warning: variable 'l_sect' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de> Acked-by: Stefan Roese <sr@denx.de>
Following PHYs can be used by set CONFIG_PHY_SMSC to config.
- SMSC LAN8700
- SMSC LAN8710/LAN8720
- SMSC LAN8710/LAN8720
A setup of PHY was copied from linux kenrel.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Fixed white space errors; modified commit message a bit. Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
mvgbe.c: In function 'mvgbe_send':
mvgbe.c:555:2: warning: dereferencing type-punned pointer will
break strict-aliasing rules [-Wstrict-aliasing]
mvgbe.c: In function 'mvgbe_recv':
mvgbe.c:640:2: warning: dereferencing type-punned pointer will
break strict-aliasing rules [-Wstrict-aliasing]
Stephen Warren [Fri, 28 Oct 2011 09:21:46 +0000 (09:21 +0000)]
disk: part_efi: fix regression due to incorrect buffer usage
Commit deb5ca80275e8cfa74d5680b41204e08a095eca5 "disk: part_efi: fix
**pgpt_pte == NULL" modified the code to pass "&gpt_head" to
is_gpt_valid() rather than the previous "gpt_head". However, gpt_head
is a pointer to the buffer, not the actual buffer, since it was allocated
using ALLOC_CACHE_ALIGN_BUFFER. This caused is_gpt_valid() to read the
disk block onto the stack rather than into the buffer, causing the
code to fail.
This change reverts that portion of the commit mentioned above.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Doug Anderson <dianders@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Acked-by: Mike Frysinger <vapier@gentoo.org> Tested-by: Anton Staaf <robotboy@chromium.org>
Zang Roy-R61911 [Thu, 27 Oct 2011 18:52:09 +0000 (18:52 +0000)]
Phy/Marvell: Rewrite the MV88E1111 phy config function based on kernel code
The original m88e1111s_config() does not do the SGMII mode
initialization and is buggy. Rewrite the function according to
3.0.6 kernel function m88e1111_config_init() in drivers/net/phy/marvell.c
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Acked-by: Andy Fleming <afleming@freescale.com> Cc: Kumar Gala <galak@kernel.crashing.org>
Mike Frysinger [Wed, 12 Oct 2011 19:47:51 +0000 (19:47 +0000)]
sparc: fix unknown escape sequence warnings
I don't know what exactly the code was going for, but the object code
is the same before/after my change, and in looking at the env strings,
this seems to be OK.
Wolfgang Denk [Mon, 5 Dec 2011 20:32:42 +0000 (21:32 +0100)]
Merge branch 'marek.vasut@gmail.com' of git://git.denx.de/u-boot-staging
* 'marek.vasut@gmail.com' of git://git.denx.de/u-boot-staging:
tools/os_support: add OS X Lion support
board/esd/dasa_sim/flash.c: Fix GCC 4.6 warning
board/esd/common/xilinx_jtag_micro.c: Fix GCC 4.6 warning
Andreas Bießmann [Thu, 24 Nov 2011 21:36:16 +0000 (22:36 +0100)]
tools/os_support: add OS X Lion support
OS X Lion's c-library implements getline(), therefore prevent including the old
helper implementation for __DARWIN_C_LEVEL < 200809L.
Without this patch following error occours:
---8<---
In file included from os_support.h:32,
from img2srec.c:55:
getline.h:1: error: conflicting types for ‘getline’
/usr/include/stdio.h:449: error: previous declaration of ‘getline’ was
here
--->8---
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Mike Frysinger [Thu, 27 Oct 2011 08:59:59 +0000 (04:59 -0400)]
sh: avoid multiple definition errors with cache funcs
Recent builds for SH4 boards fail with a lot of errors like:
cmd_mem.o: In function 'dcache_invalid_range':
include/asm/cache.h:25: multiple definition of 'dcache_invalid_range'
include/asm/cache.h:25: first defined here
This is due to the funcs being defined in the header, but not static
or inline or extern. So move them to the sh4-specific cache.c file.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
sh: Add a flag which controls the DDR ECC mode of sh7757lcr
When DDR-ECC is effective, the physical memory which can be used
reduces this boardby half. However, this mode can chenge to disable.
When it was disabled, user can use 512 MB of physical memory.
Mike Frysinger [Thu, 13 Oct 2011 04:45:47 +0000 (00:45 -0400)]
sh: only add -mno-fdpic if the compiler supports it
Not all SuperH toolchains support -mno-fdpic. Chances are good that if
the flag doesn't work, it isn't defaulting to the FDPIC ABI, so the flag
isn't needed. So only add it if it is actually supported.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
net: sh_eth: use miiphybb instead of own mii functions
The sh_eth driver had an own mii functions. However the function
didn't support the gigabit PHY. The U-Boot has the general phy driver
and miiphybb driver, and they already support it.
So this patch removes the own functions and uses the phy driver.
Wolfgang Denk [Thu, 1 Dec 2011 23:17:49 +0000 (00:17 +0100)]
Merge branch 'master' of ssh://gemini/home/wd/git/u-boot/master
* 'master' of ssh://gemini/home/wd/git/u-boot/master:
board/emk/top860/top860.c: Fix GCC 4.6 build warning
board/sbc405/strataflash.c: Fix GCC 4.6 build warning
arch/powerpc/cpu/mpc86xx/cpu.c: Fix GCC 4.6 build warning
board/freescale/mpc8610hpcd/mpc8610hpcd.c: Fix GCC 4.6 build warning
board/mpl/common/flash.c: Fix GCC 4.6 build warning
post/board/lwmon5/gdc.c: Fix GCC 4.6 build warning
drivers/usb/host/sl811-hcd.c: Fix GCC 4.6 build warning
board/sandburst/common/flash.c: Fix GCC 4.6 build warning DB64460: Fix GCC 4.6 build warnings DB64360: Fix GCC 4.6 build warnings
board/cray/L1/flash.c: Fix GCC 4.6 build warning
drivers/block/sata_dwc.c: Fix GCC 4.6 build warning
board/amirix/ap1000/flash.c: Fix GCC 4.6 build warning
alpr board: Fix GCC 4.6 build warnings
image: Don't detect XIP images as overlapping.
image: Implement IH_TYPE_KERNEL_NOLOAD
ppc4xx: Add Io64 board support
ppc4xx: fix PMC440 painit command
ppc4xx: remove invalid access to PCI_BRDGOPT2 register
ppc4xx: use CONFIG_PCI_BOOTDELAY instead of private implementation
mpc85xx: support for Freescale COM Express P2020
arch/powerpc/cpu/mpc8xxx/ddr/interactive.c: Fix GCC 4.6 build warning
mpc85xx: support board-specific reset function
powerpc/85xx: verify the localbus device tree address before booting the OS
mpc8xxx: update module_type values from JEDEC DDR3 SPD Specification
powerpc/p3060qds: Add board related support for P3060QDS platform
powerpc/85xx: clean up and document the QE/FMAN microcode macros
powerpc/85xx: always implement the work-around for Erratum SATA_A001
powerpc/85xx: CONFIG_FSL_SATA_V2 should be defined in config_mpc85xx.h
powerpc/85xx: Add workaround for erratum A-003474
powerpc/85xx: fixup flexcan device tree clock-frequency
powerpc/85xx: Add workaround for erratum CPU-A003999
x86: Fix some bugs in the i8402 driver when no controller is present
x86: Make the i8042 driver checkpatch clean
x86: Wrap small helper functions from libgcc to avoid an ABI mismatch
x86: Import the glibc memset implementation
x86: Fix a few recently added bugs
x86: Don't relocate symbols which point to things that aren't relocated
x86: Fix how the location of the realmode and bios blobs are calculated
x86: Misc cleanups
x86: Misc PCI touchups
x86: Ensure IDT and GDT remain 16-byte aligned post relocation
x86: Provide more configuration granularity
x86: Add multiboot header
sc520: Create arch asm-offsets
x86: Punt cold- and warm-boot flags
cosmetic: checkpatch cleanup of board/eNET/*.c
cosmetic: checkpatch cleanup of arch/x86/lib/*.c
cosmetic: checkpatch cleanup of arch/x86/cpu/sc520/*.c
cosmetic: checkpatch cleanup of arch/x86/cpu/*.c
x86: Call hang() on unrecoverable exception
menu.c: use puts() instead of printf() where possible
MAKEALL: drop obsolete mx31pdk_nand target
dataflash: fix parameters order in write_dataflash()
hawkboard: Replace HAWKBOARD_KICK{0, 1}_UNLOCK defines
davinci_sonata: define CONFIG_MACH_TYPE for davinci_sonata board
davinci_schmoogie: define CONFIG_MACH_TYPE for davinci_schmoogie board
arm: a320evb: define mach-type in board config file
OMAP3: Use sdelay from arch/arm/cpu/armv7/syslib.c instead of cloning that.
Fix Stelian's email address
DIU: 1080P and 720P support
CFB: Fix font rendering on mx5 framebuffer
Fix: db64460.c: In function 'debug_led': db64460.c:413:6: warning: variable 'dummy' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64460_eth_real_open':
mv_eth.c:423:6: warning: variable 'port_status' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64460_eth_stop':
mv_eth.c:641:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64460_eth_xmit':
mv_eth.c:717:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64460_eth_receive':
mv_eth.c:802:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64460_eth_get_stats':
mv_eth.c:901:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64460_eth_update_stat':
mv_eth.c:929:24: warning: variable 'dummy' set but not used [-Wunused-but-set-variable]
mv_eth.c:928:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64460_eth_print_stat':
mv_eth.c:1010:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'eth_clear_mib_counters':
mv_eth.c:2067:15: warning: variable 'dummy' set but not used [-Wunused-but-set-variable]
sdram_init.c: In function 'check_dimm':
sdram_init.c:289:50: warning: variable 'trrd_clocks' set but not used [-Wunused-but-set-variable]
sdram_init.c:289:37: warning: variable 'tras_clocks' set but not used [-Wunused-but-set-variable]
sdram_init.c:289:24: warning: variable 'trcd_clocks' set but not used [-Wunused-but-set-variable]
sdram_init.c:289:8: warning: variable 'trp_clocks' set but not used [-Wunused-but-set-variable]
sdram_init.c:279:34: warning: variable 'devicesForErrCheck' set but not used [-Wunused-but-set-variable]
sdram_init.c: In function 'setup_sdram':
sdram_init.c:1255:13: warning: variable 'check' set but not used [-Wunused-but-set-variable]
sdram_init.c: In function 'initdram':
sdram_init.c:1744:25: warning: variable 'check' set but not used [-Wunused-but-set-variable]
sdram_init.c:1742:14: warning: variable 's1' set but not used [-Wunused-but-set-variable]
sdram_init.c:1742:6: warning: variable 's0' set but not used [-Wunused-but-set-variable]
Note: no attempt was make to clean up the mess coding style and
other issues in sdram_init.c
Fix: db64360.c: In function 'debug_led': db64360.c:413:6: warning: variable 'dummy' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64360_eth_real_open':
mv_eth.c:424:6: warning: variable 'port_status' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64360_eth_stop':
mv_eth.c:642:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64360_eth_xmit':
mv_eth.c:718:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64360_eth_receive':
mv_eth.c:803:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64360_eth_get_stats':
mv_eth.c:902:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64360_eth_update_stat':
mv_eth.c:930:24: warning: variable 'dummy' set but not used [-Wunused-but-set-variable]
mv_eth.c:929:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'mv64360_eth_print_stat':
mv_eth.c:1011:15: warning: variable 'port_num' set but not used [-Wunused-but-set-variable]
mv_eth.c: In function 'eth_clear_mib_counters':
mv_eth.c:2068:15: warning: variable 'dummy' set but not used [-Wunused-but-set-variable]
sdram_init.c: In function 'check_dimm':
sdram_init.c:289:50: warning: variable 'trrd_clocks' set but not used [-Wunused-but-set-variable]
sdram_init.c:289:37: warning: variable 'tras_clocks' set but not used [-Wunused-but-set-variable]
sdram_init.c:289:24: warning: variable 'trcd_clocks' set but not used [-Wunused-but-set-variable]
sdram_init.c:289:8: warning: variable 'trp_clocks' set but not used [-Wunused-but-set-variable]
sdram_init.c:279:34: warning: variable 'devicesForErrCheck' set but not used [-Wunused-but-set-variable]
sdram_init.c: In function 'setup_sdram':
sdram_init.c:1256:13: warning: variable 'check' set but not used [-Wunused-but-set-variable]
sdram_init.c: In function 'initdram':
sdram_init.c:1735:25: warning: variable 'check' set but not used [-Wunused-but-set-variable]
sdram_init.c:1733:14: warning: variable 's1' set but not used [-Wunused-but-set-variable]
sdram_init.c:1733:6: warning: variable 's0' set but not used [-Wunused-but-set-variable]
Note: no attempt was make to clean up the mess coding style and
other issues in sdram_init.c
Wolfgang Denk [Tue, 29 Nov 2011 22:17:44 +0000 (22:17 +0000)]
alpr board: Fix GCC 4.6 build warnings
Fix:
fpga.c: In function 'fpga_pre_fn':
fpga.c:88:16: warning: variable 'reg' set but not used
[-Wunused-but-set-variable]
nand.c: In function 'alpr_nand_dev_ready':
nand.c:125:18: warning: variable 'val' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de> Acked-by: Stefan Roese <sr@denx.de>
Wolfgang Denk [Thu, 1 Dec 2011 22:58:11 +0000 (23:58 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
* 'master' of git://git.denx.de/u-boot-mpc85xx:
mpc85xx: support for Freescale COM Express P2020
arch/powerpc/cpu/mpc8xxx/ddr/interactive.c: Fix GCC 4.6 build warning
mpc85xx: support board-specific reset function
powerpc/85xx: verify the localbus device tree address before booting the OS
mpc8xxx: update module_type values from JEDEC DDR3 SPD Specification
powerpc/p3060qds: Add board related support for P3060QDS platform
powerpc/85xx: clean up and document the QE/FMAN microcode macros
powerpc/85xx: always implement the work-around for Erratum SATA_A001
powerpc/85xx: CONFIG_FSL_SATA_V2 should be defined in config_mpc85xx.h
powerpc/85xx: Add workaround for erratum A-003474
powerpc/85xx: fixup flexcan device tree clock-frequency
powerpc/85xx: Add workaround for erratum CPU-A003999
Stephen Warren [Thu, 10 Nov 2011 20:17:54 +0000 (13:17 -0700)]
image: Don't detect XIP images as overlapping.
bootm_load_os() detects when it writes the decompressed image over
the top of the compressed image. If this happens, the original image
is corrupted. When the original image is a multi-component legacy image,
or a (potentially multi-component) FIT image, this implies that other
components may be corrupted. In turn, this means that booting is unlikely
to be successful.
However, in the case of no image compresssion coupled with an image with
load address equal to where the image is already located (e.g. an XIP
kernel, or IH_TYPE_KERNEL_ANYLOAD), there has been no copy and hence no
corruption, no matter whether it's a single-component legacy image, a
multi-component legacy image, or a FIT image. In this case, disable the
overlap detection, and allow boot to continue.
Without this change, when booting a single-component legacy image that
contains an IH_TYPE_KERNEL_ANYLOAD, bootm_load_os() would have returned
BOOTM_ERR_OVERLAP, but the caller ignores this, and boot continues and
succeeds. Now, the false error is no longer even returned.
Without this change, when booting a FIT image that contains an
IH_TYPE_KERNEL_ANYLOAD, bootm_load_os() would have returned
BOOTM_ERR_OVERLAP, which would then cause the caller to reset the board.
Now, the false error is no longer returned, and boot succeeds.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Stefan Roese <sr@denx.de>
projects / u-boot / log