Kim Phillips [Wed, 16 Jan 2008 06:38:05 +0000 (00:38 -0600)]
Add support for the MPC837xERDB
MPC837xERDB board support includes:
* DDR2 330MHz hardcoded (soldered on the board)
* Local Bus NOR Flash
* I2C, UART and RTC
* eTSEC RGMII (TSEC0 - RTL8211B with MII;
* TSEC1 - VSC7385 local bus, hardcoded, requires seperate firmware
* load)
Signed-off-by: Kevin Lam <kevin.lam@freescale.com> Signed-off-by: Joe D'Abbraccio <joe.d'abbraccio@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Kim Phillips [Wed, 16 Jan 2008 18:06:16 +0000 (12:06 -0600)]
mpc83xx: add support for more system clock performance controls
System registers that are modified are the Arbiter Configuration
Register (ACR), the System Priority Control Register (SPCR), and the
System Clock Configuration Register (SCCR).
Signed-off by: Michael F. Reiss <Michael.F.Reiss@freescale.com>
Signed-off by: Joe D'Abbraccio <ljd015@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
James Yang [Wed, 16 Jan 2008 17:58:08 +0000 (11:58 -0600)]
FSL: Generalize PIXIS reset command parsing.
Before, the order of arguments to the pixis_reset
command needed to be supplied in a hard-coded order.
Generalize the command parsing to allow any order.
Signed-off-by: James Yang <james.yang@freescale.com> Acked-by: Jon Loeliger <jdl@freescale.com>
Jon Loeliger [Tue, 15 Jan 2008 19:42:41 +0000 (13:42 -0600)]
FSL: Convert board/freescale/common/Makefile to use CONFIG_
Convert the board/freescale/common/Makefile to use
CONFIG_* options to select which files to conditionally
compile into the board/freescale/common library rather
than conditionally compiling entire files.
Now handles::
CONFIG_FSL_PIXIS
CONFIG_FSL_DIU_FB
CONFIG_PQ_MDS_PIB
CONFIG_ID_EEPROM is introduced until CFG_ID_EEPROM is gone.
Kim Phillips [Tue, 15 Jan 2008 15:51:12 +0000 (09:51 -0600)]
mpc83xx: clean up mpc8360emds.c warnings
mpc8360emds.c: In function 'ft_board_setup':
mpc8360emds.c:327: warning: assignment makes pointer from integer without a cast
mpc8360emds.c:329: warning: passing argument 2 of 'fdt_getprop' makes integer from pointer without a cast
mpc8360emds.c:334: warning: passing argument 2 of 'fdt_setprop' makes integer from pointer without a cast
mpc8360emds.c:341: warning: assignment makes pointer from integer without a cast
mpc8360emds.c:343: warning: passing argument 2 of 'fdt_getprop' makes integer from pointer without a cast
mpc8360emds.c:348: warning: passing argument 2 of 'fdt_setprop' makes integer from pointer without a cast
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Poonam Aggrwal [Mon, 14 Jan 2008 04:11:14 +0000 (09:41 +0530)]
Changes in uboot DDR configuration for MPC8313eRDB
These changes were identified by HighSmith Bill ,Mazzyar and Joseph for
DDR configuration in u-boot code. Some are related to performance, some
affect stability and some correct few basic errors in the current
configuration.
The changes have been tested and found to give better memory latency
figures on MPC8313eRDB.LMBench figures prove it.
The changes are:
- CS0_CONFIG[ AP_n_EN] is changed from 1 to 0
(this may improve performance for application with many read
or write to open pages).
- CS0_CONFIG[ODT_WR_CFG] is currently changed from 100 to
001 (activating all the CS when only one is used may cause
unwanted noise on the system)
- TIMING_CFG_1[ACTTOPRE] is changed from 9clks to 8clks (based on
Tras=45ns)
- TIMING_CFG_1[REFREC] changed from 21 clks to 18clks.
- TIMING_CFG_2[AL] value changed from 0 setting to 1 clk to
comply with the 3 ODT clk requirements)
- TIMING_CFG_2[CPO] was set to a reserved value, changed to RL+3/4.
- TIMING_CFG_2[FOUR_ACT] is changed from 10 clks to 6clks.
- DDR_SDRAM_MODE[AL]changed from 0 to 1.
- DDR_SDRAM_MODE[WRREC] changed from 1 clk to 3 clks.
- DDR_SDRAM_INTERVAL[REFINT] is changed from 0x0320 to 0x0510.
- DDR_SDRAM_INTERVAL[BSTOPRE] is changed from 0x64 to 0x0500.
Jerry Van Baren [Sat, 12 Jan 2008 18:24:14 +0000 (13:24 -0500)]
Enable the isdram command on the MPC8360EMDS board
The isdram command prints out decoded information the "serial presence
detect" (SPD) chip on the SDRAM SIMMs. This can be very helpful when
debugging memory configuration problems.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Dave Liu [Fri, 11 Jan 2008 10:48:24 +0000 (18:48 +0800)]
mpc83xx: Add the support for MPC8315ERDB board
The features list:
- Boot from NOR Flash
- DDR2 266MHz hardcoded configuration
- Local bus NOR Flash R/W operation
- I2C, UART, MII and RTC
- eTSEC0/1 support
- PCI host
Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Dave Liu [Mon, 14 Jan 2008 03:12:01 +0000 (11:12 +0800)]
QE: fix compile warning
qe.c: In function 'qe_upload_firmware':
qe.c:390: warning: pointer targets in passing argument 2
uec.c: In function 'uec_initialize':
uec.c:1236: warning: 'uec_info' may be used uninitialized
Stefan Roese [Mon, 14 Jan 2008 09:05:05 +0000 (10:05 +0100)]
ppc4xx: Update Kilauea CPLD configuration with USB PHY reset bit
Now that bit 29 is the USB PHY reset bit, update the Kilauea port
to remove the USB PHY reset after powerup. The CPLD will keep the
USB PHY in reset (active low) until the bit is set to 1 in
board_early_init_f().
- get rid of "version" target whichdidn't really work
- make autoconf.mk depend on version_autogenerated.h to make sure
to rebuild files as needed
- add XECHO macro to allow for silent build using "make -s"
Larry Johnson [Fri, 11 Jan 2008 03:23:39 +0000 (22:23 -0500)]
Fix "i2c sdram" command for DDR2 DIMMs
Many of the SPD bytes for DDR2 SDRAM are not interpreted correctly by the
"i2c sdram" command. This patch provides correct alternative
interpretations when DDR2 memory is detected.
Wolfgang Denk [Sat, 12 Jan 2008 19:31:39 +0000 (20:31 +0100)]
Fix linker scripts: add NOLOAD atribute to .bss/.sbss sections
With recent toolchain versions, some boards would not build because
or errors like this one (here for ocotea board when building with
ELDK 4.2 beta):
ppc_4xx-ld: section .bootpg [fffff000 -> fffff23b] overlaps section .bss [fffee900 -> fffff8ab]
For many boards, the .bss section is big enough that it wraps around
at the end of the address space (0xFFFFFFFF), so the problem will not
be visible unless you use a 64 bit tool chain for development. On
some boards however, changes to the code size (due to different
optimizations) we bail out with section overlaps like above.
The fix is to add the NOLOAD attribute to the .bss and .sbss
sections, telling the linker that .bss does not consume any space in
the image.
Add support for the TK885D baseboard from TELE-DATA
The TK885D board uses a TQM885D module from TQ, this port adds an
own configuration file and adds a last_stage_init() method to
configure the two PHYs, depending on the phy_auto_nego environment
variable.
Fix video console newline and carriage return handling
Lines of the lenght CONSOLE_COLS or greater than CONSOLE_COLS
are not displayed correctly. This is an attempt to fix
this issue. Also add carriage return handling.
Dave Liu [Thu, 10 Jan 2008 15:05:00 +0000 (23:05 +0800)]
mpc83xx: Fix the typo in mpc83xx.h
The SPCR about TSEC priority is wrong.
Signed-off-by: Michael Barkowski <Michael.Barkowski@freescale.com> Signed-off-by: Joe D'Abbraccio <Joe.D'abbraccio@freescale.com> Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Anton Vorontsov [Wed, 9 Jan 2008 17:57:47 +0000 (20:57 +0300)]
mpc83xx: add support for the MPC8360E-RDK
This is MPC8360E based board with:
- 256MB fixed SDRAM;
- 8MB Intel Strata NOR flash;
- StMICRO 64MiB NAND flash;
- two 10/100/1000 ethernet ports connected via Broadcom
BCM5481 PHYs;
- two 10/100 ethernet ports connected via National
DP83848 PHYs;
- one PCI and one miniPCI slots;
- four serial ports (two NS16550-compatible, two UCCs);
- four USB ports working through MPC8360E "FHCI" USB controller;
- Fujitsu MB86277 graphics controller;
- Analog to Digital Converter/Touchscreen controller, AD7843
connected to SPI.
Features not supported in this patch are:
- StMICRO 64MiB NAND flash (patch sent);
- MINT framebuffer initialization (patch is pending);
- Fetching production information from the EEPROM via I2C;
- FHCI USB;
- Two slow UCCs used as RS-485 UARTs.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Becky Bruce [Thu, 10 Jan 2008 20:00:28 +0000 (14:00 -0600)]
86xx: Support 2GB DIMMs
Configure the number of bits used to address the banks inside the SDRAM
device. The default register value of 0 means 2 bits to address 4 banks.
Higher capacity devices like a 2GB DIMM require 3 bits to address 8 banks.
Ben Warren [Wed, 9 Jan 2008 23:15:53 +0000 (18:15 -0500)]
Fix Ethernet init() return codes
Change return values of init() functions in all Ethernet drivers to conform
to the following:
>=0: Success
<0: Failure
All drivers going forward should return 0 on success. Current drivers that
return 1 on success were left as-is to minimize changes.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com> Acked-by: Stefan Roese <sr@denx.de> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Kim Phillips <kim.phillips@freescale.com> Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Acked-By: Timur Tabi <timur@freescale.com>
projects / u-boot / log