Esben Haabendal [Fri, 23 Oct 2015 08:12:59 +0000 (10:12 +0200)]
cfi: support for 16-bit flash with reversed endianness
This is for targets where flash controller has reverse endianness
compared to target. For these, the 'bus_swap' parameter can be given to the
CFI driver, which will cause command CFI commands to be written with
bytes swapped. This is only for x16 CFI flash.
Due to signal propagation delays, sampling TDO on rising TCK can become
quite peculiar at fast TCK rates. However, FTDI chips offer a possiblity
to sample TDO on falling edge. With this change, stable operation can be
achieved at 30MHz clock even over 10cm ribbon cable.
Ivan De Cesaris [Tue, 12 Jan 2016 15:30:18 +0000 (16:30 +0100)]
quark: add Intel Quark mcu D2000 support
Add support for the Intel Quark mcu D2000 using the new quark_d2xx
target.
Changes to the lakemont part are needed for the D2000 core and
backwards compatible with the X1000 one.
Change-Id: I6e1ef5a5d116344942f08e413965abd3945235fa Signed-off-by: Ivan De Cesaris <ivan.de.cesaris@intel.com>
Reviewed-on: http://openocd.zylin.com/3199 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Alexander Kurz [Sat, 13 Feb 2016 09:54:52 +0000 (10:54 +0100)]
Helper time_support: const function arguments
duration_elapsed and duration_kbps will not modify the struct duration
passed as function argument, hence it should be declared const.
Change-Id: I459c396952c78e907257e2c2f2c630abde92aaa8 Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-on: http://openocd.zylin.com/3232 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tomas Vanek [Sat, 9 Jan 2016 17:56:23 +0000 (18:56 +0100)]
adi_v5_swd: invalidate dap->select during (re)connect
Commit 830d0c55c0920606366a15560d1945f1e1942744 introduced
a regression in error recovery after reconnect:
If first SWD queue run in dap_dp_init() fails, DP_SELECT
does not get reset.
Change-Id: I947e2afe9933e4645a6141ece7816af8e6082cf2 Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3194 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Paul Fertser [Fri, 15 Jan 2016 10:22:28 +0000 (13:22 +0300)]
flash: nor: {pic32mx,cfi}: fix register names
Commit fd43be07265b5f3cf3146f2bb80c1c2fc0a44fcf introduced a
regression: since the register names were changed from those
traditional for MIPS to common GDB scheme the code that makes use of
them needs to be changed accordingly.
This commit restores pic32mx flash driver functionality.
Change-Id: Id18c739390fae36737a02dc30c363d0444f53b96 Reported-by: Louis Rannou <louson@users.sf.net> Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3206 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Bogdan Kolbov [Mon, 14 Dec 2015 13:52:30 +0000 (16:52 +0300)]
flash/nor/niietcm4: minor fixes
niietcm4_write() buffer padding:
add correct buffer padding for 16 bytes.
Args check in FLASH_BANK_COMMAND_HANDLER():
first version of the driver had 7 args, current - 6. This patch will fix
error when flash is rejected (current k1921vk01t.cfg has flash bank init
with 6 args).
Timeouts in flash flag checking procedure:
increase timeouts in niietcm4_opstatus_check() and niietcm4_uopstatus_check()
cause there were problems in some hardware configurations.
JTAG ID:
wrong id in k1921vk01t.cfg replaced with right one.
Jiri Kastner [Wed, 20 Jan 2016 10:21:41 +0000 (11:21 +0100)]
arm_adi_v5: dap_partnums - correction of partnumbers, new added
according to...
ARM DDI 0433B is:
0x9a5 Cortex-A5 PMU
ARM DDI 0435C is:
0x955 Cortex-A5 ETM
ARM DDI 0401C is:
0x950 Cortex-A9 PTM
ARM DDI 0469B is:
0x931 Cortex-R5 ETM
ARM DDI 0460D is:
0xc15 Cortex-R5 Debug
ARM DDI 0458C is:
0x9b7 Cortex-R7 PMU
0xc17 Cortex-R7 Debug
ARM DDI 0535C is:
0x95b Cortex-A17 PTM
0x9ae Cortex-A17 PMU
0xc0e Cortex-A17 Debug
ARM DDI 0500F is:
0x9a8 Cortex-A53 CTI
0x95d Cortex-A53 ETM
0x9d3 Cortex-A53 PMU
0xd03 Cortex-A53 Debug
ARM DDI 0488G is:
0x906 Cortex-A57/A72 CTI
0x95e Cortex-A57 ETM
0x9d7 Cortex-A57 PMU
0xd07 Cortex-A57 Debug
ARM 100095_0002_03_en is:
0x95a Cortex-A72 ETM
0x9d8 Cortex-A72 PMU
0xd08 Cortex-A72 Debug
dap_sync() executes all commands in the JTAG queue and then checks
if a WAIT condition happened inside the last batch. If yes, a recovery
is invoked. If not, processing continues without checking for
errors. This function should be called in long AP read or writes, e.g.
while uploading a new application binary, at intermediate points within
the transfer where the cost of flushing the JTAG queue and checking the
journal doesn't affect performance too much.
ADIv5 specifies that DP and AP accesses may generate a WAIT
response when the hardware is not able to complete a request for various
reasons in time before the next request is sent. Currently, the software
treats a WAIT response as a fatal error and aborts operation on the DAP.
This patch implements WAIT handling by keeping a journal of all
outstanding and completed accesses, including their response status.
At certain times (when dap_run() is called), the journal is inspected
for WAIT responses and all discarded accesses are replayed to complete
them. Special care is taken to not re-execute already successfully
completed operations.
Peter A. Bigot [Mon, 4 Jan 2016 20:37:43 +0000 (14:37 -0600)]
jlink: deconflict local variables from global symbols
BeagleBone debian 7 builds produce:
jlink.c: In function 'jlink_speed':
jlink.c:218:11: error: declaration of 'div' shadows a global declaration [-Werror=shadow]
jlink.c: In function 'check_trace_freq':
jlink.c:1065:54: error: declaration of 'div' shadows a global declaration [-Werror=shadow]
jlink.c: In function 'config_trace':
jlink.c:1101:11: error: declaration of 'div' shadows a global declaration [-Werror=shadow]
Fix this by changing the local variable to 'divider'.
Change-Id: I96a0cc0f7d4d4af5a56aa1e918e5416d3c61cbfe Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Reviewed-on: http://openocd.zylin.com/3185 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Peter A. Bigot [Thu, 31 Dec 2015 15:13:58 +0000 (09:13 -0600)]
arm_adi_v5: deconflict local variables from global symbols
BeagleBone debian 7 builds produce:
adi_v5_jtag.c: In function 'jtag_ap_q_bankselect':
adi_v5_jtag.c:336:11: error: declaration of 'select' shadows a global declaration [-Werror=shadow]
Fix this by changing the local variable to 'sel'.
Change-Id: I8e29662ac12bc77d38d5064046d59b7364853cd9 Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Reviewed-on: http://openocd.zylin.com/3184 Tested-by: jenkins Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Peter Lawrence [Mon, 28 Dec 2015 21:53:49 +0000 (22:53 +0100)]
ARM ADIv5: CoreSight ROM decode part number and designer id
The existing arm_adi_v5.c code decodes CoreSight peripherals based
on the part number field. However, these are specific to a
particular manufacturer (often ARM). The same part number from
two different manufacturers (distinct designer ids) should not
decode as the same CoreSight peripheral.
The Analog Devices ADSP-SC58x and ADSP-BF70x have peripherals that
overlap with existing OpenOCD decoding. The part number is the
same as existing OpenOCD decoding, but have a different JEP106 code.
Most, if not all, of the existing part number entries in
arm_adi_v5.c are probably specific to ARM. Change all entries
suspected to be designed by ARM to match only ARM's designer ID.
However, to preserve legacy behavior, existing non-ARM entries are
encoded with a wildcard so that they will behave in the same way as
the existing legacy code. It is desirable, however, to start
encoding the data with designer codes to avoid such ambiguity.
Revising the code to check both the part number and designer id
seemed to a warrant a const array lookup table instead of a
multi-tiered switch statement.
Also try to sync part identification IDs with relevant ARM docs.
Change-Id: Iac1374e4cfc6f04cebb479c0e3fa9bde527cc4a3 Signed-off-by: Peter Lawrence <majbthrd@gmail.com>
[andreas.fritiofson@gmail.com: change JEP106 to designer ID, cleanup] Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3128 Tested-by: jenkins
cortex_a: add 'dacrfixup' to cortex-a command group
work around issues with software breakpoints when the text segment
is mapped read-only by the OS. Set DACR to "all-manager" to bypass
TLB permission checks on memory access.
AM335x: allow simultaneous debugging of A8 and M3 cores
This patch fixes the tap order so that it matches the actual jtag
chain when all taps are enabled. It also introduces a variable
DEFAULT_TAPS that can be set outside of this script, e.g. on the
command line, to specify which taps are to be enabled on init.
Lastly, a new debug target "am335x.m3" is added so that the Wakeup-M3
can be selected for debugging.
Andreas Färber [Sat, 28 Nov 2015 23:17:05 +0000 (00:17 +0100)]
tcl/board: Add Infineon XMC4700 Relax Kit Series config
Tested with Relax Kit for 5V Shields:
J-Link Lite-XMC4200 Rev.1 compiled Oct 14 2015 10:14:50
and with Relax Lite Kit:
J-Link Lite-XMC4200 Rev.1 compiled Oct 14 2015 10:14:50
Derived from xmc4800-relax.cfg.
Change-Id: I4e10fb6ed1f85168634d3b5259d3041ffc6b74d8 Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3130 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Matthew Campbell [Tue, 24 Nov 2015 14:05:38 +0000 (09:05 -0500)]
sysfsgpio: support broken gpio implementations
Change tests when reading from 'value' in sysfs from =='0' to !='1'.
This guards against broken sysfs GPIO implementations that return
non-zero for high rather than just '1' while still being clean and
correct code. Note that sysfs will never output a leading zero even
in a very broken implementation as that is covered in gpiolib.c, not
the offending driver.
Tested against broken Freescale kernel 3.14.38 on i.MX6SL.
Change-Id: Id05567bb8504b1babef33d6ee5172bceefeca8b8 Signed-off-by: Matthew Campbell <mcampbell@izotope.com>
Reviewed-on: http://openocd.zylin.com/3121 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
On JTAG, all reads are pipelined. If you read a register, the result is not
delivered inside the request that issued the read, it is delivered in the
following request. The current code therefore issues a scan of the RDBUFF
register after each read. This adds a superfluous transaction after each
read.
This patch follows a strategy similar to what SWD already implements.
It also leverages that all JTAG reads are pipelined, i.e. the result
will be clocked out in the next JTAG data phase, no matter if it's
READ or WRITE. Therefore it's never necessary to explicitly read RDBUFF
other than for the very last READ before a dap_run().
Debug initialization blindly selects AP#0 as default, which is the AHB-AP
in many cases. This sets the default for target_read/write functions.
However, AHB-AP is the wrong choice, because it bypasses caches on read
and write and also makes some peripherals inaccessible (e.g. l2 outer
caches). This patch explicitely selects the APB-AP (debug_ap) as the
default.
Remove entirely the concept of a "selected" AP that has to be maintained
between calls. All the information the DAP ops need are now provided to
each call through the AP/DAP pointer.
Consolidate the cache of the SELECT fields into one single field caching
the entire register.
arm_adi_v5: Remove all cases of "restoring" previous dap_ap_select()
All AP operations should select the AP to use before calling it so
there's no point in restoring the previous value afterwards.
The explicit call to dap_ap_select() before all AP operations should be
moved into dap_queue_ap_read/write() which then would have to take the
AP as an argument instead of the DAP.
adi_v5_jtag: Remove TAR and CSW prints from jtagdp_transaction_endcheck
The AP for which the TAR/CSW is printed may not be the one that caused
the failure. Remove the flawed output entirely. The correct info is
printed in mem_ap_read/write anyway.
All mem_ap_* functions now make sure the SELECT register is updated with
the AP number that it's operating on. This shouldn't have to be handled
explicitly.
This function does two separate things, powering up the DP and setting
up a MEM-AP. But the DP needs to be powered before even searching for a
MEM-AP to initialize and targets may have multiple MEM-APs that need
initializing.
Split the function into dap_dp_init() and mem_ap_init() and change all
call sites to use the appropriate one.
arm_adi_v5: Convert the AP references from numbers to pointers
Change the debug_ap and memory_ap fields of the cortex_a target and
the debug_ap field of the cortex_m target to be pointers to the
struct adiv5_ap instead of AP numbers in some known DAP.
This reduces the dependency on the DAP struct in the targets and
enables MEM-AP accesses to take the relevant AP as parameter.
arm_adi_v5: Add a back-pointer from an AP to its DAP
This will make it possible to reference directly the AP used for debug
in the target instance and remove the DAP reference. This will in turn
enable getting rid of the need to select an "active" AP in the DAP (using
dap apsel).
target/arm: Remove usage of struct arm_jtag in ARMv7 targets
The Cortex-A and Cortex-M keeps an arm_jtag struct around just to be
able to pass a pointer to it to one common JTAG function which anyway
only uses the TAP field.
Refactor the function to take a TAP directly, remove the legacy struct
from cortex instances and store the TAP pointer only in the DAP.
Cortex-M makes a call to arm_jtag_setup_connection() with the struct
but the function does nothing useful for a Cortex-M target so remove
the call.
Making the SWD driver aware of the DAP that controls it is a layering
violation.
The only usage for the DAP pointer is to store the number of idle cycles
the AP may need to avoid WAITs. Replace the DAP pointer with a cycle
count hint instead to avoid future misuse.
Change-Id: I3e64e11a43ba2396bd646a4cf8f9bc331805d802 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3141 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Patrick Stewart [Mon, 28 Sep 2015 12:51:58 +0000 (13:51 +0100)]
arm_debug: Support multiple APs per DAP and remove DAP from armv7* structs
Separate out the values from adiv5_dap that are associated with a specific AP into a new struct, so we can properly support multiple APs. Remove the DAP struct from the armv7* structs, because we can have multiple CPUs per DAP, and we shouldn't have multiple DAP structs. Tidy up a few places where ap_current is used incorrectly.
Change-Id: I0c6ef4b49cc86b140366347aaf9b76c07cbab0a8 Signed-off-by: Patrick Stewart <patstew@gmail.com>
Reviewed-on: http://openocd.zylin.com/2984 Tested-by: jenkins Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Patrick Stewart [Sat, 5 Dec 2015 23:18:33 +0000 (00:18 +0100)]
cortex_m: Select an AP when accessing the DAP
Prepare to support multiple cortex-m cores on one DAP. Uses mem_ap_sel_*
functions and removes mem_ap_* functions. Adds a new debug_ap
parameter to the cortex_m (currently set to zero as in existing code).
Change-Id: I6926029d1e7bf44a42d453d1aff349bda824ba72 Signed-off-by: Patrick Stewart <patstew@gmail.com>
Reviewed-on: http://openocd.zylin.com/2983 Tested-by: jenkins Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Alamy Liu [Thu, 6 Aug 2015 21:05:24 +0000 (14:05 -0700)]
adi_v5: Rename AP_REG_* to MEM_AP_REG_* and add LA support
This is a TODO in the src/target/arm_adi_v5.h for MEM-AP registers.
Some new registers are introduced in ADIv5.2 specification.
MEM_AP_REG_MGT (0x20) // Memory Barrier Transfer register
MEM_AP_REG_TAR64 (0x08) // Bits[63:32] of Transfer Address
MEM_AP_REG_BASE64 (0xF0) // Bits[63:32] of Debug Base Address
Refer to
7.5 MEM-AP register summary in
IHI0031C: ARM Debug Interface Architecture Specification ADIv5.0 to ADIv5.2
Change-Id: I3bc4296a04c35f5c64f851e5865d3099922613fa Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Reviewed-on: http://openocd.zylin.com/2904 Tested-by: jenkins Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Alamy Liu [Thu, 6 Aug 2015 23:17:50 +0000 (16:17 -0700)]
cortex-a: Fix "Detected core" number is always '0'
Problem
No matter what target->coreid is, it always shows
Detected core 0 dbgbase: ...
In dap_lookup_cs_component(), it decreases the core index value to zero
in order to find the desired core.
The reference to coreidx is necessary considering "a device which has nested
ROM tables, with each core described in its own table." (by Paul Fertser).
Change-Id: I9b56d45d6edf6639e748a625ab27787f8e5a5776 Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Reviewed-on: http://openocd.zylin.com/2902 Tested-by: jenkins Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
cortex_a_read_apb_ab_memory_fast() uses the wrong order of ITR and DSCR
writes when setting up the transfer. ARM DDI0406C says in C8.2 regarding
"Fast mode" operation to first switch to fast mode and then latch the
instruction in ITR. Current implementation first wrote ITR, causing
the instruction to be executed immediately, then switched to fast mode
without an instruction latched. Repeated reading of DTRTX didn't
execute LDC and thus replicated its current content into the whole buffer.
This patch uses the following, revised algorithm:
1) switch to non-blocking mode and issue the LDC for the first word
2) if more than one word is to be read:
- switch to fast mode
- latch the LDC instruction into ITR (it is _not_ executed)
- issue (count-1) reads of DTRTX register, each read returns the current
content of DTRTX and re-issues the latched instruction
-> now the second-to-last word is in the buffer and the LDC for the last
word has been issued.
3) wait for the last instruction to complete
4) switch back to non-blocking mode
5) Read DTRTX for the last (or: only) word and put it into the buffer
Change-Id: I44f5c585962ffa5af257c3d5a2a802c122b6b1e4 Signed-off-by: Matthias Welwarsky <matthias@welwarsky.de>
Reviewed-on: http://openocd.zylin.com/3122 Tested-by: jenkins Reviewed-by: Christopher Head <chead@zaber.com> Reviewed-by: Paul Fertser <fercerpav@gmail.com>
When accessing memory through the ARM core, privilege levels and mmu
access permissions observed. Thus it depends on the current mode of the
ARM core whether an access is possible or not. the ARM in USR mode can
not access memory mapped to a higher privilege level. This means, if the
ARM core is halted while executing at PL0, the debugger would be
prevented from setting a breakpoint at an address with a higher privilege
level, e.g. in the OS kernel. This is not desirable.
cortex_a_check_address() tried to work around this by predicting if an
access would fail and switched the ARM core to SVC mode. However, the
prediction was based on hardcoded address ranges and only worked for
Linux and a 3G/1G user/kernel space split.
This patch changes the policy to always switch to SVC mode for memory
accesses. It introduces two functions cortex_a_prep_memaccess() and
cortex_a_post_memaccess() which bracket memory reads and writes. These
function encapsulate all actions necessary for preparation and cleanup.
when disabling the mmu to access physical addresses, normally the d-cache
must be disabled as well. Disabling the d-cache also requires a full
clean&invalidate. However, since all memory writes are treated as write-
through no-allocate and memory reads do not allocate cache lines,
effectively the d-cache state does not change at all. We can therefore
save the the d-cache disabling and flushing.
cortex_a: force cache and tlb bypass when cpu is in debug state
for minimal impact on the hardware state, force all memory accesses to
bypass the caches and tlbs. This may actually be the default, but ARM
recommends in DDI0406C to set proper default values on debug init.
cortex_a: Update instruction cache after setting a soft breakpoint
Call armv7a_l1_d_cache_flush_virt() before writing the breakpoint,
to make sure the d-cache is clean and invalid at the breakpoint
location down to PoC.
Call armv7a_l1_d_cache_inval_virt() after writing the breakpoint
again, so that d-cache will pick up the modified code.
Call armv7a_l1_i_cache_inval_virt() after writing the breakpoint
to memory to make the change visible to the CPU.
armv7a: correctly handle invalidation of inner data caches
D-Cache invalidate is a dangerous operation. It will only work correctly
if full cache lines are invalidated. When partial cache lines are
invalidated, i.e. the target address range does not start and end
at a cache line boundary, cpu data writes outside of the target range
will be dropped. This patch adds special treatment for partial cache
lines by doing a clean & invalidate on the partial lines before
invalidating the rest of the range.
The following changes are implemented:
- Clean&Invalidate the VA range to PoC *before* the write takes place
- Remove SMP handling since DCCIMVA instruction already maintains SMP
coherence.
- Remove separate Invalidate step
ARMv7 architecture allows up to 7 cache levels that are architecturally
visible, as opposed to "system caches", which are outside of the domain
defined by ARMv7 and require separate management. This patch enables
detection and identification of caches at all levels. It also implements
a new "flush-all" function that cleans & invalidates all cache levels to
the "Point of Coherence".
armv7a: remove special l2x flush-all and cache-info handlers
This patch is on the path to unified handlers for both inner and
outer caches. It removes the special overrides installed when
an outer cache is configured.
Alamy Liu [Wed, 12 Aug 2015 00:03:57 +0000 (17:03 -0700)]
adi_v5: Fix wrong ap value
Problem
dap->ap_current is register value, not field value.
it restores invalid ap when it calls dap_ap_select(dap, ap_old) later.
* assume the current ap is 1, dap->ap_current value would be (1 << 24).
ap_old = dap->ap_current; <-- ap_old = 1<<24 = 0x1000000.
...
dap_ap_select(dap, ap_old); <-- select 0x1000000, not 1.
* All AP registers accessing fail afterwards.
One of the reproducible case(s): CORE residents in AP >= 1
dap_lookup_cs_component() being used to find PE(*).
In most cases, PE would be found in AP==0, hence the problem is hidden.
When AP number is 1, dap->ap_current would have the value of 1<<24.
Anyone get the AP value with dap->ap_current and resotre it later would
select the wrong AP and all accessing later would fail.
The ARM Versatile and/or FPGA would have better chance to provide this
kind of environment that PE residents in AP>=1. As they have an 'umbrella'
system at AP0, and main system at AP>=1.
* PE: Processing Element. AKA Core. See ARM Glossary at
http://infocenter.arm.com/help/topic/com.arm.doc.aeg0014g/ABCDEFGH.html
Fix
Use dap_ap_get_select() to get ap value.
a. Retrieve current ap value by calling dap_ap_get_select();
src/flash/nor/kinetis.c
src/target/arm_adi_v5.c
b. The code is correct (dap->ap_current >> 24), but it's better to use
dap_ap_get_select() so everything could be synchronized.
src/flash/nor/sim3x.c
Change-Id: I97b5a13a3fc5506cf287e299c6c35699374de74f Signed-off-by: Alamy Liu <alamy.liu@gmail.com>
Reviewed-on: http://openocd.zylin.com/2935 Reviewed-by: Andreas Färber <afaerber@suse.de> Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
Marc Schink [Mon, 20 Oct 2014 17:18:38 +0000 (13:18 -0400)]
Improve J-Link driver and introduce libjaylink.
This patch uses libjaylink which is a library to access J-Link
devices. As other tools which are not in the scope of OpenOCD also
need to access J-Link devices a library is used. A firmware upgrade
tool and an advanced configuration tool for J-Link devices are under
development.
Further versions of libjaylink will support additional features
OpenOCD could benefit from. This includes TCP/IP as additional
possibility to connect to J-Link devices as well as power tracing and
device internal communication. The latter is used to access
peripherals on some development boards (e.g EFM32 STK and DVK).
Integration of libjaylink is realized with a git submodule like
jimtcl. As libjaylink depends on libusb-1.0 only, no additional
dependency is introduced for OpenOCD.
All low-level JTAG and SWD implementations of the current driver are
left untouched and therefore no incompabilities are to be expected.
Improvements of this patch:
* Support for more USB Product IDs, including those with the new
scheme (0x10xx). The corresponding udev rules are also updated.
* Device selection with serial number and USB address.
* Adaptive clocking is now correctly implemented and only usable for
devices with the corresponding capability.
* The target power supply can now be switched without the need for
changing configuration and power cycling the device.
* Device configuration is more restrictive and only allowed if the
required capabilities are available.
* Device configuration now shows the changes between the current
configuration of the device and the values that will be applied.
* Device configuration is verified after it is written to the device
exactly as the vendor software does.
* Connection registration is now handled properly and checks if the
maximum number of connections on a device is reached. This is also
necessary for devices which are attached via USB to OpenOCD as
some device models also support connections on TCP/IP.
* Serial Wire Output (SWO) can now be captured. This feature is not
documented by SEGGER however it is completely supported by
libjaylink.
This patch and libjaylink were tested on Ubuntu 14.04 (i386),
Debian 7 (amd64), FreeBSD 10.0 (amd64) and Windows XP SP3 (32-bit)
with the following device and target configurations:
* JTAG: J-Link v8.0, v9.0 and v9.3 with AT91SAM7S256
* SWD: SiLabs EFM32 STK 3700 (EFM32GG990F1024)
* SWD: J-Link v8.0, v9.0 and v9.3 with EFM32GG990F1024
* SWD: XMC 2Go (XMC1100)
* SWD: XMC1100 Boot Kit (XMC1100)
* SWD: IAR Systems / Olimex Eval Board (LPC1343F)
* SWD: Nordic Semiconductor nRF51 Dongle (nRF51422)
* SWD: SiLabs EZR32 WSTK 6220A (EZR32WG330FG60G)
Except for Windows XP all builds are tested with Clang in addition to
GCC. This patch and libjaylink are not tested on OSX yet.
Change-Id: I8476c57d37c6091c4b892b183da682c548ca1786 Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/2598 Tested-by: jenkins Reviewed-by: Andreas Färber <afaerber@suse.de> Reviewed-by: Paul Fertser <fercerpav@gmail.com> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Jakub Kubiak [Wed, 27 May 2015 19:52:41 +0000 (21:52 +0200)]
flash/nor/lpc2000: add alternative part ID for LPC1343
http://support.code-red-tech.com/CodeRedWiki/DebugAccessChip
> Note that once you have recovered debug access to your MCU, then in most cases you should then modify your Debug Configuration to turn vector catch off again. If this is not done, then this can cause problems in some circumstances with some versions of the Code Red IDE. For example with NXP LPC13xx parts, connecting more than once to the MCU with vector catch enabled can lead to the part ID being incorrectly read - which can again cause debug connections to fail
This patch adds an alternative part ID for LPC1343. With this patch "program" command works fine for flashing.
Change-Id: I8632e898a4c33102455925d25715b4f4edfa1d97 Signed-off-by: Jakub Kubiak <jakub@kubiak.es>
Reviewed-on: http://openocd.zylin.com/2782 Tested-by: jenkins Reviewed-by: Andreas Färber <afaerber@suse.de> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Felipe Balbi [Thu, 9 Apr 2015 18:31:17 +0000 (13:31 -0500)]
jtag: commands: save a pointer to list tail
By saving a pointer to the tail of the list,
we don't need to traverse the entire command
queue before we're able to append an item to
it.
With this patch, I see a 10% improvement when
using the embedded XDS100v2 on AM437x IDK board
to load a 4MiB binary (linux zImage) to DDR
with load_image.
Paul Fertser [Fri, 20 Nov 2015 10:08:20 +0000 (13:08 +0300)]
svf: fix progress reporting switch behaviour
The svf_progress_enabled variable is global, hence its lifetime is not
limited and it retains the value from the previous run. Fix this by
explicit assignment.
Tomas Vanek [Wed, 7 Oct 2015 14:09:21 +0000 (16:09 +0200)]
Kinetis: suppress false alarms "MCU is secured"
Kinetis driver checks MDM STAT register to detect secured state of MCU.
An unsecured clean device typically triggered a huge fat alarm message.
Now when driver detects secured state it tries to halt MCU and then
re-reads status register.
Command "mdm mass_erase" used to deassert reset when finished
and MCU started looping in hard fault - WDOG reset cycle.
Now "reset halt" is issued. Clean flash is not run after mass_erase.
Change-Id: I23f393509fbd8751d44ffc744ff2d67f1074f74e Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3010 Tested-by: jenkins Reviewed-by: Thomas Schmid <thomas@rfranging.com> Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Jonathan Larmour [Mon, 16 Nov 2015 12:18:19 +0000 (12:18 +0000)]
tcl/board: Remove pflash.0 bank from twr-k60n512.cfg
The pflash.0 bank should not be present as it overlaps with
the flash bank created by target/kx.cfg, triggering an error.
This is also in line with the existing twr-k60f120m.cfg.
Change-Id: I5f620e01319d967f12e029fb6865ccdd031713b3 Signed-off-by: Jonathan Larmour <jifl@eCosCentric.com>
Reviewed-on: http://openocd.zylin.com/3108 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tomas Vanek [Tue, 27 Oct 2015 11:49:17 +0000 (12:49 +0100)]
flash: at91samd: flash write code cleaning
SAMD driver suffered from following problems:
1) Flash was erased as an integral part of flash write.
It was not documented so with usual workflow it resulted
in erasing flash twice (and reducing flash lifespan)
and in almost double flashing time.
2) Sector erase was silently skipped if "is_erased" flag was set.
"is_erased" logic was not reliable, e.g. when a row write
was aborted after successful write of some pages, sector was
still considered as erased. "is_erased" flag could not
cope with flash writes from a user program.
3) Writing of a block with start address unaligned to a flash page
resulted in failed assert and OpenOCD abort.
4) Disabling cache in bit 18 of 16-bit halfword never worked.
MCU implements cache invalidate in hardware so there is no need
to take care about. This bug was reported by Tony DiCola.
New code does not erase flash in write operation.
Instead it traditionally relies on erasing flash beforehand.
"is_erased" logic and cache disabling is completely removed.
It simplifies write procedure a lot and flash write is now faster.
Andreas Loehre [Thu, 6 Aug 2015 17:41:10 +0000 (19:41 +0200)]
flash: at91samd: Add SAML21 variant B device support and fix SAMC20/SAMC21
This adds support for the Atmel SAML21 variant B parts.
There is minimal change between the two variants, but in
variant B the automatic page write which the at91samd flash
driver relies on to be enabled is disabled by default.
With this patch the write row function will now issue a page write
command after each of the four pages in the row if the MANW (manual
write) bit is set. This also fixes flash write for the SAMC20/SAMC21
devices which have the MANW bit set by default as well.
I have also moved the device ID (DID) register bitfield extraction
from the find_part into helper macros. These can be used in the future
if there are more workarounds for specific devices.
Tested (programming) on:
ATSAML21-XPRO
ATSAML21-XPRO-B
SAMC21 Xplained Pro
SAMD21 Xplained Pro
SAMD20 Xplained Pro
Change-Id: I401a8aa1efd64730840c0d62cf49a1e880ea5900 Signed-off-by: Andreas Loehre <alohre@gmail.com>
Reviewed-on: http://openocd.zylin.com/2903 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tomas Vanek [Thu, 5 Nov 2015 20:05:43 +0000 (21:05 +0100)]
jtag: cmsis-dap: Issue disconnect before reconnecting
cmsis-dap protocol has both DAP_Connect and DAP_Disconnect commands.
Logically if cmsis_dap_swd_switch_seq() calls DAP_Connect in connected
state it should call DAP_Disconnect first.
Doing so surprisingly solves problems on Atmel EDBG with target SAMD/R/L/C.
Without this change SWD communication breaks after reset run/halt
in config "reset_config srst_only" and reconnect trials repeatedly
fail with "SWD ack not OK: 0 JUNK"
Change-Id: Ie951098d5e0c83f388e2df414608aaabec2135c9 Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3098 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tomas Vanek [Fri, 15 May 2015 09:14:11 +0000 (11:14 +0200)]
at91samd: handle reset run/halt in DSU
Atmel introduced a "Device Service Unit" (DSU) that holds the CPU
in reset if TCK is low when srst (RESET_N) is deasserted.
Function is similar to SMAP in ATSAM4L, see http://openocd.zylin.com/2604
Atmel's EDBG adapter handles DSU reset correctly without this change.
An ordinary SWD adapter leaves TCK in its default state, low.
So without this change any use of sysresetreq or srst
locks the chip in reset state until power is cycled.
A new function dsu_reset_deassert is called as reset-deassert-post event handler.
It optionally prepares reset vector catch and DSU reset is released then.
Additionally SWD clock comment is fixed in at91samdXX.cfg and clock is
lowered a bit to ensure a margin for RC oscillator frequency deviation.
adapter_nsrst_delay 100 is commented out because is no more necessary after
http://openocd.zylin.com/2601
Change-Id: I42e99b1b245f766616c0a0d939f60612c29bd16c Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2778 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
projects / openocd / log