Soren Brinkmann [Thu, 21 Nov 2013 21:39:00 +0000 (13:39 -0800)]
net: zynq_gem: Move RCLK details out of driver
The GEM driver should not need to know about Zynq specific details of
RCLK related registers and bitfields in the SLCR. Move those details to
the slcr driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Fri, 22 Nov 2013 14:29:38 +0000 (15:29 +0100)]
zynq: timer: Fix hangs if network activity attempted after about one hour
Cortex-A9 MPCore TRM' from ARM (ARM DDI 0407G ID072711) describes
in the section 4.1.1 how this value calculation should be done.
This patch fixes the problem if network activity such as ping or
tftp is attempted after u-boot has been idle for an hour,
it hangs, and cannot control-C out of it.
Signed-off-by: Uday Hegde <udayh@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Gerlando Falauto [Thu, 13 Feb 2014 15:43:00 +0000 (16:43 +0100)]
arm/km: introduce kmsugp1 target
KMSUGP1 is from a u-boot perspective (almost) identical to KMNUSA.
The only difference is that the PCIe reset is connected to Kirkwood pin
MPP7_PEX_RST_OUTn, we use a dedicated config flag KM_PCIE_RESET_MPP7.
Such pin should theoretically be handled by the PCIe subsystem
automatically, but this turned out not to be the case.
So simply configure this PIN as a GPIO and issue a pulse manually.
Gerlando Falauto [Mon, 27 Jan 2014 15:58:28 +0000 (16:58 +0100)]
arm/km: define fdt_high env variable and allow backwards compatibility
Add set_fdthigh subcommand to "subbootcmds" (release) so to set "fdt_high"
This is necessary on Kirkwood so that the FDT does not get relocated
above the memory limit that the kernel cannot access
(that is the memory part reserved for the switch).
This was tested on NUSA1, where it is necessary, and on ETER1, where it
doesn't seem to hurt.
We want the scripts to also work with older versions of u-boot, where:
a) set_fdthigh is not defined (will be default env for newer u-boots)
b) the fdt will not be available
For this reason, we use "set_fdthigh" to tell whether we are running
a newer (FDT-aware) u-boot or not.
So if "set_fdthigh" runs successfully or arch != arm we try loading
the fdt; otherwise we proceed normally.
Notice how, contrary to release mode, set_fdthigh will _not_ be part of
subbootcmds for develop and ramfs, but will be executed as part of
"tftpfdt".
Since this is only needed for kirkwood cards, and it prevents the kernel
from booting on QorIQ (though it seemed to work on ETER1), we change
its definition in the default env for powerpc so that the value is only
set on ARM.
Gerlando Falauto [Mon, 27 Jan 2014 15:58:27 +0000 (16:58 +0100)]
arm/km: enable FDT for km_kirwkood
This consists of:
a) Defining the addresses, enabling fdtsupport [arm]
b) Defining "cramfsloadfdt" [arm,powerpc => common]
c) Adding the FDT address to bootm [arm,powerpc => common]
d) Defining "tftpfdt" in ramfs-,develop- [arm,powerpc >= common]
This should work with 3.10 kernels, whether loaded through TFTP
(with rootfs either through NFS or TFTP-ramfs) or from the NAND.
The machid was left unchanged, this should keep compatibility with both
older and newer kernels.
Stephen Warren [Wed, 29 Jan 2014 05:42:06 +0000 (22:42 -0700)]
ARM: bcm2835: config.mk isn't needed
The entries in config.mk were needed so that U-Boot could be built
with an old version of the Raspberry Pi Foundation's toolchain. Without
them, the build would error out with:
...-ld: error: .../libgcc.a(_bswapsi2.o) uses VFP register arguments,
u-boot does not
However, none of the 3 toolchains in the latest version of their
tools.git, nor the Ubuntu/Linaro ARM compilers in at least Ubuntu Quantal
or Saucy, need these options set in order to compile a working U-Boot.
Hence, remove the options for simplicity.
Reported-by: Tom Rini <trini@ti.com> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Andreas Färber <afaerber@suse.de>
Stephen Warren [Wed, 29 Jan 2014 05:41:50 +0000 (22:41 -0700)]
ARM: rpi_b: set $fdtfile in default environment
U-Boot names the Raspberry Pi board rpi_b. This means that the common
expression for DTB filename ${soc}-${board}.dtb expands to
bcm2835-rpi_b.dtb. However, the DTB generated by the Linux kernel is
bcm2835-rpi-b.dtb. Set $fdtfile in U-Boot's environment so that scripts
look for the correct DTB filename.
An alternative would be to rename the U-Boot board to rpi-b. However,
that change would be far more invasive, and end up affecting users (i.e
they'd have to change their U-Boot build commands).
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Markus Niebel [Wed, 5 Feb 2014 09:51:25 +0000 (10:51 +0100)]
ARM: imx6: fix wrong fec clk
imx_get_fecclk() returns enet_ref instead of ipg.
Since the clock is used to calculate the prescaler
for the MDIO interface wrong values can be calculated.
Tested on a custom MX6S board with 100MBit interface
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Fabio Estevam [Wed, 29 Jan 2014 19:39:49 +0000 (17:39 -0200)]
mx6: Enable L2 cache support
Add L2 cache support and enable it by default.
Configure the L2 cache in the same way as done by FSL kernel:
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/tree/arch/arm/mach-mx6/mm.c?h=imx_3.0.35_4.1.0
Anson Huang [Thu, 23 Jan 2014 06:00:19 +0000 (14:00 +0800)]
imx6: make sure MMDC_CHx_MASK is clear to avoid warm reset failure
Boot ROM may mask MMDC_CHx_MASK in CCM_CCDR(such as i.MX6SL TO1.2),
it will cause warm reset fail, need to clear this MMDC_CHx_MASK field
to make sure all the i.MX6 series SOCs reset function work. Otherwise,
uboot "reset" command will fail, tested on i.MX6SL EVK board with TO1.2.
Anson Huang [Thu, 23 Jan 2014 06:00:18 +0000 (14:00 +0800)]
imx6: ensure AHB clock is 132MHz in low freq boot mode
For low freq boot mode(ARM boot up with 396MHz), ROM
will not set AHB clock to 132MHz, and the reset value of
AHB divider is incorrect which will lead to wrong AHB
rate, need to correct it. To enable low freq boot mode,
need to set BOOT_CFG2[2] to high, tested on i.MX6Q/DL
SabreSD board and i.MX6SL EVK board.
Fabio Estevam [Wed, 22 Jan 2014 14:23:32 +0000 (12:23 -0200)]
mx6sl: Adjust fdt_addr to avoid address overlapping
Similarly as it was done on commit 6584a1b526 (ARM: mx6: Change the FDT loading
address to avoid overlaping), we need to adjust the fdt_addr in order to be
able to boot FSL 3.10 kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Otavio Salvador [Thu, 16 Jan 2014 21:58:06 +0000 (19:58 -0200)]
vf610twr: Set default environment to use zImage
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Otavio Salvador [Thu, 16 Jan 2014 21:58:05 +0000 (19:58 -0200)]
udoo: Set default environment to use zImage
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Otavio Salvador [Thu, 16 Jan 2014 21:58:04 +0000 (19:58 -0200)]
mx6slevk: Set default environment to use zImage
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Otavio Salvador [Thu, 16 Jan 2014 21:58:03 +0000 (19:58 -0200)]
mx6sabre_common: Set default environment to use zImage
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Otavio Salvador [Thu, 16 Jan 2014 21:58:02 +0000 (19:58 -0200)]
mx6qarm2: Set default environment to use zImage
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Otavio Salvador [Thu, 16 Jan 2014 21:58:01 +0000 (19:58 -0200)]
mx53loco: Set default environment to use zImage
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Otavio Salvador [Thu, 16 Jan 2014 21:58:00 +0000 (19:58 -0200)]
mx51evk: Set default environment to use zImage
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Otavio Salvador [Thu, 16 Jan 2014 21:57:59 +0000 (19:57 -0200)]
mx28evk: Set default environment to use zImage
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Otavio Salvador [Thu, 16 Jan 2014 21:57:58 +0000 (19:57 -0200)]
mx23evk: Set default environment to use zImage
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Otavio Salvador [Thu, 16 Jan 2014 21:57:57 +0000 (19:57 -0200)]
hummingboard: Set default environment to use zImage
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Otavio Salvador [Thu, 16 Jan 2014 21:57:56 +0000 (19:57 -0200)]
cgtqmx6eval: Set default environment to use zImage
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The implementation of oc_serial_setbrg() for CONFIG_SYS_NIOS_FIXEDBAUD and
!CONFIG_SYS_NIOS_FIXEDBAUD are very similar.
Add a baudrate variable and set it to either CONFIG_BAUDRATE or gd->baudrate.
Then we can unify the code for both cases.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Tom Rini [Wed, 5 Feb 2014 15:24:23 +0000 (10:24 -0500)]
cmd_mmc.c: Drop open/close mmc sub-commands
The open and close mmc sub-commands implement a hard-coded set of values
specific to the SMDK5250 platform. Remove these commands as what they
did can be done instead with a series of mmc dev / bootpart / bootbus
commands instead now.
Cc: Amar <amarendra.xt@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Tom Rini [Wed, 5 Feb 2014 15:24:22 +0000 (10:24 -0500)]
cmd_mmc.c: Add bootbus mmc sub-command
Add a bootbus sub-command to the mmc command to allow for setting
the boot_bus_width, reset_boot_bus_width and boot_mode fields of
BOOT_BUS_WIDTH (EXT_CSD[177]).
Tom Rini [Wed, 5 Feb 2014 15:24:21 +0000 (10:24 -0500)]
cmd_mmc.c: Add 'partconf' command to mmc
Add a partconf sub-command to the mmc command to allow for setting
the boot_ack, boot_partition and partition_access fields of
PARTITION_CONFIG (formerly BOOT_CONFIG, EXT_CSD[179]). Part of this
requires changing the check for 'part' from an strncmp to a strcmp, like
the rest of the sub-commands.
Cc: Andy Fleming <afleming@gmail.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Tom Rini [Wed, 5 Feb 2014 15:24:18 +0000 (10:24 -0500)]
SPL: Add CONFIG_SUPPORT_EMMC_BOOT support to CONFIG_SPL_FRAMEWORK
We use the switch CONFIG_SUPPORT_EMMC_BOOT today to enable some
additional features of the eMMC boot partitions. Add support for being
told that we have booted from one of these partitions to the spl
framework and implement this on TI OMAP/related.
As per the below commit
"mmc: sdhci: add the quirk for broken r1b response"
(sha1: 3a6383207be3f71b39004e64464a6e99290b16fa)
need to add quirk SDHCI_QUIRK_BROKEN_R1B, when the
response type is R1b.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
This patch corrects the divider value written to CLKDIV register.
Since SDCLKIN is divided inside controller by the DIVRATIO value set
in the CLKSEL register, we need to use the same output clock value to
calculate the CLKDIV value.
as per user manual: cclk_in = SDCLKIN / (DIVRATIO + 1)
Input parameter to mmc_clk is changed to dwmci_host, since
we need the same to read DWMCI_CLKSEL register.
This improves the read timing values for channel 0 on SMDK5250
from 0.288sec to 0.144sec
Stephen Warren [Thu, 30 Jan 2014 23:11:12 +0000 (16:11 -0700)]
mmc: set rca to 1 for MMC cards
U-Boot currently sets MMC cards' RCA register to 0. This value is
reserved according to the specification. Use a value of 1 instead, just
like the Linux kernel.
Alexey Brodkin [Wed, 22 Jan 2014 16:49:09 +0000 (20:49 +0400)]
net/designware: make driver compatible with data cache
Up until now this driver only worked with data cache disabled.
To make it work with enabled data cache following changes were required:
* Flush Tx/Rx buffer descriptors their modification
* Invalidate Tx/Rx buffer descriptors before reading its values
* Flush cache for data passed from CPU to GMAC
* Invalidate cache for data passed from GMAC to CPU
Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Vipin Kumar <vipin.kumar@st.com> Cc: Stefan Roese <sr@denx.de> Cc: Mischa Jonker <mjonker@synopsys.com> Cc: Shiraz Hashim <shiraz.hashim@st.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Amit Virdi <amit.virdi@st.com> Cc: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Alexey Brodkin [Wed, 22 Jan 2014 16:54:06 +0000 (20:54 +0400)]
net/designware - switch driver to phylib usage
With this change driver will benefit from existing phylib and thus
custom phy functionality implemented in the driver will go away:
* Instantiation of the driver is now much shorter - 2 parameters
instead of 4.
* Simplified phy management/functoinality in driver is replaced with
rich functionality of phylib.
* Support of custom phy initialization is now done with existing
"board_phy_config".
Note that after this change some previously used config options
(driver-specific PHY configuration) will be obsolete and they are simply
substituted with similar options of phylib.
For example:
* CONFIG_DW_AUTONEG - no need in this one. Autonegotiation is enabled
by default.
* CONFIG_DW_SEARCH_PHY - if one wants to specify attached phy
explicitly CONFIG_PHY_ADDR board config option has to be used, otherwise
automatically the first discovered on MDIO bus phy will be used
I believe there's no need now in "doc/README.designware_eth" because
user only needs to instantiate the driver with "designware_initialize"
whose prototype exists in "include/netdev.h".
Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Vipin Kumar <vipin.kumar@st.com> Cc: Stefan Roese <sr@denx.de> Cc: Mischa Jonker <mjonker@synopsys.com> Cc: Shiraz Hashim <shiraz.hashim@st.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Amit Virdi <amit.virdi@st.com> Cc: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Alexey Brodkin [Fri, 10 Jan 2014 15:58:11 +0000 (19:58 +0400)]
net: execute "miiphy_init" if CONFIG_PHYLIB defined
In "common/Makefile" "miiphyutil.o" gets built if any of the following
items enabled:
* CONFIG_PHYLIB
* CONFIG_MII
* CONFIG_CMD_MII
So it's possible to not define CONFIG_MII or CONFIG_CMD_MII and still
use functions like "miiphy_get_dev_by_name".
In its turn "miiphy_get_dev_by_name" traverses "mii_devs" list which is
not initialized because "miiphy_init" never got called.
Cc: Rob Herring <rob.herring@calxeda.com> Cc: Simon Glass <sjg@chromium.org> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Alexey Brodkin [Tue, 4 Feb 2014 08:56:13 +0000 (12:56 +0400)]
arc: add architecture header files
These are header files used by ARC700 architecture.
Also note that "arch-arc700/hardware.h" is only required for compilation of
"designware_i2c" driver which refers to "asm/arch/hardware.h".
It would be good to fix mentioned driver sometime soon but it will cause
changes in ARM board configs that use "designware_i2c".
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Francois Bedard <fbedard@synopsys.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de>
Aaron Wu [Wed, 23 Nov 2011 03:23:56 +0000 (11:23 +0800)]
blackfin: Initialize the EMAC VLAN with proper default value
EMAC_VLANx regs is not properly initiallized in u-boot, once it's overwrite in the
kernel when DSA enabled, hot reset will lead to bringing up EMAC fail in u-boot.
Signed-off-by: Aaron Wu <Aaron.Wu@analog.com> Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
projects / u-boot / log