Add missing cmd_ximg.o to common/Makefile

Signed-off-by: Marian Balakowicz <m8@semihalf.com>

ADS5121e: DDR2 init/timing update.

Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>

Device tree updates

Changes to match 5121 device tree going mainline in 2.6.25.

Change OF_SOC from "soc5121" to plain "soc".
Remove unneeded "ref-frequency" fixups.
Remove "address" enetaddr fixup.

Add bus-frequency fixup for old OF_SOC so old
kernels with old device trees will work with new
u-boot with 66MHz IPS clock

Signed-off-by: John Rigby <jrigby@freescale.com>

Change IPS freq to 66MHz

Recommended frequency is 66MHz
Change divider from 4 to 3.

Signed-off-by: John Rigby <jrigby@freescale.com>

xsengine: rename board_post_init to board_late_init

missing migration from "Cleanup of some init functions"
in c837dcb1a316745092567bfe4fb266d0941884ff

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Add attribute POST_PREREL to ECC memory POST

Signed-off-by: Larry Johnson <lrj@acm.org>

TFTP: add host ip addr support

allow to use a different server as set in serverip
add CONFIG_TFTP_FILE_NAME_MAX_LEN to configure the file name length
if not defined the max length will be at 128

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

OMAP5912: fix FIFO handling in UART driver

According to the OMAP5912 Serial Interfaces Reference Guide (see
http://focus.ti.com/lit/ug/spru760c/spru760c.pdf, page 150), the
FIFO_EN enable bit in the FIFO Control Register (FCR) can only be
changed when the baud clock is not running, i. e. when both DLL and
DLH are set to 0.

Thus make sure that DLL and DLH are 0 when writing the FCR.

Signed-off-by: Wolfgang Denk <wd@denx.de>

ARM: S3C24x0 SoC NAND controller support

This patch adds NAND support to the S3C24x0 SoC code in u-boot

Signed-off-by: Harald Welte <laforge@openmoko.org>

ARM: s3c24xx: Multiple serial port support

This patch adds support for CONFIG_SERIAL_MULTI on s3c24x0 CPU's

Signed-off-by: Harald Welte <laforge@openmoko.org>

ARM: arm920t: Allow use of 'gd' pointer from IRQ

This patch allows us to use the 'gd' pointer (and thus environment
and everything else associated with it) from interrupt context on
arm920t.

Signed-off-by: Harald Welte <laforge@openmoko.org>

ARM: arm920/s3c24xx: IRQ demulitplexer callback

This patch adds a IRQ demultiplexer callback to the arm920 cpu core code,
plus a stub implementation of it for the S3C2410.

The purpose is to allow arm920t implementations such as the s3c24x0 to
implement interrupt handlers in u-boot without having to touch core
arm920t code.

Signed-off-by: Harald Welte <laforge@openmoko.org>

ARM: Display Ethernet info in do_bdinfo only if CONFIG_CMD_NET is defined

Add ifdef to bdinfo command to display ethernet information
only if CONFIG_CMD_NET is defined for arm modules.

Signed-off-by: K R Gururaja Hebbar <gururajakr@sanyo.co.in>

ARM: add I2C init function call in lib_arm/board.c

Adds I2C init func call to init sequence for ARM boards. This is
present in ppc,blackfin and other processor init sequence.

Signed-off-by: K R Gururaja Hebbar <gururajakr@sanyo.co.in>

ARM: Board voiceblue update

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>

ARM: AT91RM9200 based boards config cleanup

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Remove nowhere used struct bd_info_ext, remove trailing whitespaces, fix
indentation.

ARM: Fix at91rm9200dk base address

Somewhere during development of U-Boot-1.1.3 CONFIG_BOOTBINFUNC was
renamed into CONFIG_INIT_CRITICAL which was 04 Apr 2005 replaced
with CONFIG_SKIP_LOWLEVEL_INIT and CONFIG_SKIP_RELOCATE_UBOOT.
However CONFIG_SKIP_LOWLEVEL_INIT has oposite meaning to
CONFIG_BOOTBINFUNC, so fix configuration to reflect this fact.
I'm sending this patch 4th (!) time in hope it produces at least some
reaction.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Fix at91rm9200dk base and environment address.

MMC for PXA 27X (resubmit)

MMC support for X_Scale PXA is broken and does not work.
Mainly, the mmc_init() function cannot recognize current SD/MMC cards.
There were already some patches around the world but none of them was
merged into the official u-boot tree.

This patch makes order fixing this issue. Resubmit after code cleanup.

Applied and tested on PXA 270 (TrizepsIV module).

Signed-off-by: Stefano Babic <sbabic@denx.de>

Fix gcc issues in pxa-regs.h

Fix gcc4 issue. With some toolchain, a previous patch that fixes gcc4
issues generates wrong code.
(Problem was reported with gcc-4.0.2-glibc-2.3.6/arm-softfloat-linux-gnu).
This patch fixes the problem and solves the gcc-4 issues as the linux
kernel does.

Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Dmitry Ivanov <ivadmitry@gmail.com>

inka4x0: remove dead code

Signed-off-by: Wolfgang Denk <wd@denx.de>

Coding Style Cleanup; update CHANGELOG

Signed-off-by: Wolfgang Denk <wd@denx.de>

Merge ../custodians

Merge branch 'master' of git://www.denx.de/git/u-boot-ixp

Merge ../custodians

Merge branch 'master' of git://www.denx.de/git/u-boot-mips

Merge ../custodians

Merge branch 'master' of git://www.denx.de/git/u-boot-sh

Merge ../custodians

Merge branch 'master' of git://www.denx.de/git/u-boot-avr32

Coding Style Cleanup; update CHANGELOG

Signed-off-by: Wolfgang Denk <wd@denx.de>

Merge branch 'master' of git://www.denx.de/git/u-boot-coldfire

Merge branch 'master' of git://www.denx.de/git/u-boot-net

Merge branch 'master' of git://www.denx.de/git/u-boot-ppc4xx

Merge branch 'master' of git://www.denx.de/git/u-boot-mpc86xx

Merge branch 'master' of git://www.denx.de/git/u-boot-mpc85xx

mpc83xx: Correct the struct spi8xxx in mpc8xxx_spi.h

The commit 04a9e1180ac76a7bacc15a6fcd95ad839d65bddb
cause the 83xx immap broken, so the DMA and PCI will
be failed.

The patch fix the struct spi8xxx and rm struct spi83xx.

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Merge branch 'master' of git://www.denx.de/git/u-boot

AVR32: ATNGW100 board support

Add support for the ATNGW100 Network Gateway reference design,
including flash, ethernet and MMC support.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

AVR32: Initialize ipaddr, loadaddr and bootfile at startup

I don't know why the relevant layers can't do this by itself, but this
is what ppc does.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Add AcTux board support

Hi,

The patch adds 4 boards, called AcTux-1 .. AcTux-4. This patch contains the
files that
contain changes for multiple boards, the board-specific files follow as
separate patches.

Signed-off-by: Michael Schwingen <michael@schwingen.org>

add AcTux-4 board support

Signed-off-by: Michael Schwingen <michael@schwingen.org>

add AcTux-3 board support

Signed-off-by: Michael Schwingen <michael@schwingen.org>

add AcTux-2 board support

Signed-off-by: Michael Schwingen <michael@schwingen.org>

add AcTux-1 board support

Signed-off-by: Michael Schwingen <michael@schwingen.org>

ARM: remove useless function board_post_init

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

IXP: enable RTS

enables the RTS signal with CONFIG_SERIAL_RTS_ACTIVE.
No handshaking is done, but the active RTS signal allows to
connect to the target using a PC which is using RTS/CTS
handshake, and does no harm if the PC is set to ignore RTS.

Signed-off-by: Michael Schwingen <michael@schwingen.org>

IXP: add dynamic microcode addr

allow to load the microde from flash or ram by download it through
the serial or other.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Stefan Roese <sr@denx.de>

load ixp42x NPE firmware from separate flash block, remove dead code

Hi,

the following patch adds support to move the IXP42X NPE firmware to a
separate flash block, whose start address is defined in
CONFIG_IXP4XX_NPE_EXT_UCODE_BASE. Using that, it is possible to build
NPE-enabled u-boot without copyright problems due to the NPE firmware.

I hope the patch applies, I get whitespace-related differences in the NPE
files due to trailing whitespace in the original versions.

Signed-off-by: Michael Schwingen <michael@schwingen.org>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Merge branch 'kumar'

ColdFire: MCF547x_8x - Add M5475EVB and M5485EVB support

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Signed-off by: John Rigby <jrigby@freescale.com>

ColdFire: MCF547x_8x - Add M547xEVB and M548xEVB board

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Signed-off by: John Rigby <jrigby@freescale.com>

ColdFire: Add MCF547x_8x FEC driver

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Signed-off by: John Rigby <jrigby@freescale.com>

ColdFire: Add MCF547x_8x dma code and header files

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Signed-off by: John Rigby <jrigby@freescale.com>

ColdFire: Add MCF547x_8x dma code - 2

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Signed-off by: John Rigby <jrigby@freescale.com>

ColdFire: Add MCF547x_8x dma code - 1

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Signed-off by: John Rigby <jrigby@freescale.com>

ColdFire: Add MCF547x_8x related header files

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Signed-off by: John Rigby <jrigby@freescale.com>

ColdFire: Add MCF547x_8x cpu arch

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Signed-off by: John Rigby <jrigby@freescale.com>

ColdFire: Add MCF5227x cpu and M52277EVB support-3

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Signed-off by: John Rigby <jrigby@freescale.com>

ColdFire: Add MCF5227x cpu and MCF52277EVB support-2

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Signed-off by: John Rigby <jrigby@freescale.com>

ColdFire: Add MCF5227x cpu and M52277EVB support-1

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Signed-off by: John Rigby <jrigby@freescale.com>

ColdFire: Fix CFI Flash low level Read/Write macro

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Signed-off by: John Rigby <jrigby@freescale.com>

ColdFire: Add M5373EVB platform support - 2

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Signed-off by: John Rigby <jrigby@freescale.com>

ColdFire: Add M5373EVB platform support - 1

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Signed-off by: John Rigby <jrigby@freescale.com>

ColdFire: Update FlexBus CS for MCF532x

Definition update and change from 16bit to 32bit

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Signed-off by: John Rigby <jrigby@freescale.com>

ColdFire: PCI and misc updates for MCF5445x

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Signed-off by: John Rigby <jrigby@freescale.com>

ColdFire: MCF5445x header files cleanup

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Signed-off by: John Rigby <jrigby@freescale.com>

ColdFire: MCF532x header files cleanup

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Signed-off by: John Rigby <jrigby@freescale.com>

ColdFire: Add modules header files

Add CF specific modules header files

Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Signed-off-by: John Rigby <jrigby@freescale.com>

codingstyle cleanup for spi driver

..and rm unused CONFIG_FSL_SPI define

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

FSL: Fix common EEPROM_data structure definition

- Fix EEPROM_data structure definition according to System EEPROM Data Format.
- Read MAC addresses from EEPROM to ethXaddr before saving ethXaddr to
  bd->bi_ethaddr.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>

86xx: enable command-line editing

Enable command-line editing for all MPC86xx boards.

Signed-off-by: Timur Tabi <timur@freescale.com>

Implement hard SPI driver on MPC8349EMDS

This patch implements the fsl_spi driver on the MPC8349EMDS evaluation board.
This board has an ST M25P40 4Mbit EEPROM on its SPI bus

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Add support for a Freescale non-CPM SPI controller

This patch adds support for the SPI controller found on Freescale PowerPC
processors such as the MCP834x family.  Additionally, a new config option,
CONFIG_HARD_SPI, is added for general purpose SPI controller use.

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

mpc83xx: Fix the fatal conflict of merge

The commit 9e89647889cd4b5ada5b5e7cad6cbe55737a08d7
will cause the mpc8315erdb board can't boot up.

The patch fix that bug, and remove the duplicated #ifdef
CFG_SPCR_TSECEP code and clean the SCCR_TSEC2 for
MPC8313E processor.

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Merge branch 'master' of /home/stefan/git/u-boot/u-boot

Merge Sequoia beautification into Korat code

Signed-off-by: Larry Johnson <lrj@acm.org>

net: add 'ethrotate' environment variable

[PATCH] net: add 'ethrotate' environment variable

This patch replaces the buildtime configuration option
CONFIG_NET_DO_NOT_TRY_ANOTHER through the 'ethrotate' runtime
configuration veriable. See README.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

ppc4xx: Fix compilation warnings and coding style issues in HCU4/HCU5

Signed-off-by: Stefan Roese <sr@denx.de>

sh: Remove CONFIG_COMMANDS from MS7720SE config file

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ppc4xx: Netstal HCU4 board: added various fixes and POST

- Moved some common code to netstal/common/nm_bsp.c.
- sdram initialisation goes go netstal/common/fixed_sdram.c.
- Added support for POST.
- Stylistic cleanups (multi-line comments/ enforce 80 colomn width)

Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>

ppc4xx: netstal/common define routines used by all boards

Added some routines used by all Netstal boards:
- nm_bsp.c: - nm_show_print and
        -  common_misc_init_r
        - set_params_for_sw_install. Very specific code to handle our SW
          installation procedure
- fixed_sdram.c: Common routines for HCU4 (and upcoming) MCU25 boards
  to handle sdram initialization.
- nm.h: Common header

Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>

ppc4xx: Netstal HCU5 board: added various fixes and POST

- Moved some common code to nestal/common/nm_bsp.c.
- Added support for the vxWorks EDR.
- Enable trace for Lauterbach, if present.
- Added support for POST.
- Stylistic cleanups (multi-line comments/ enforce 80 colomn width)

Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>

ppc4xx: Netstal HCU5 board. Added POST. Various fixes

- Various fixes
- Reduced rom_size from 384 to 320 kB
- Environment is now in flash
- Added POST
- Support for OF

Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>

ppc4xx: Netstal HCU4 board. Added POST. Various fixes

- Various fixes
- Reduced rom_size from 384 to 320 kB
- Environment is now in flash
- Added POST
- Support for OF

Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>

ppc4xx: Complete DU440 board support

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>

ppc4xx: Add DU440 board support

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>

Merge branch 'master' of git+ssh://10.10.0.7/home/wd/git/u-boot/master

sh: Update SuperH SCIF driver

This patch fixed wrong SH7720 CPU macro and changed macro that
calculated value of SCBRR register.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Set ips dividor to 1/4 of csb clock.

Previous setting cause ips clock to be out of spec. This bug was found by John
Rigby from Freescale.

Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>

85xx: Get ride of old TLB setup code

Now that all boards have been converted, remove old config code and the
config option for the new style.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

85xx: Convert TQM85xx to new TLB setup

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

85xx: Convert STXGP3 & STXSSA to new TLB setup

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

85xx: Convert SBC8540/SBC8560/SBC8548 to new TLB setup

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

85xx: Convert PM854/PM856 to new TLB setup

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

85xx: Convert MPC8540EVAL to new TLB setup

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

85xx: Convert MPC8568 MDS to new TLB setup

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

85xx: Convert MPC8541/MPC8555/MPC8548 CDS to new TLB setup

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

85xx: Convert MPC8540/MPC8560 ADS to new TLB setup

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

85xx: Convert ATUM8548 to new TLB setup

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

85xx: Convert MPC8544 DS to new TLB setup

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>