Retrieve RAM base address from DT instead of using STM32_SDRAM_FMC
For STM32F7, FMC block base address is 0xA0000000, but SDRAM
registers are located at offset 0x140 inside FMC block.
Update the stm32_fmc_regs fields with all FMC registers
to map SDRAM registers at the right address.
This allow to remove include/dm/platform_data/serial_stm32x7.h
which was included in the past by stm32x7 driver and by
stm32f746-disco.c board file.
Since patch 42bf5e7c27 "serial: stm32f7: add device tree support"
this file is no more needed in board file.
Add clock framework .get_rate callback.
This step will allow to convert all drivers which was using
proprietary clock_get() to use clock framework .get_rate().
configs: ti: armv7: Fixes bug in fit_loadaddr for ramfs boot
The load address of ramdisk, rdaddr is 0x88080000 and fit_loadaddr
is defined as 0x88000000. This leaves only 512Kbytes for the
fit image. When the FIT images are larger than this, it will
overwite the ramdisk and cause the boot to fail.
For eg, The K2 HS fit images are a few MB and end up overwriting
the ramdsk. This patch moves the fit_loadaddr to 0x87000000,
leaving a 16MB window for the fit image. This memory can be
reclaimed once the kernel starts running.
arm: mach-keystone: Updates mon_install for K2G HS
On early K2 devices (eg. K2HK) the secure ROM code does not support
loading secure code to firewall protected memory, before decrypting,
authenticating and executing it.
To load the boot monitor on these devices, it is necessary to first
authenticate and run a copy loop from non-secure memory that copies
the boot monitor behind firewall protected memory, before decrypting
and executing it.
On K2G, the secure ROM does not allow secure code executing from
unprotected memory. Further, ROM first copies the signed and encrypted
image into firewall protected memory, then decrypts, authenticates
and executes it.
As a result of this, we cannot use the copy loop for K2G. The
mon_install has to be modified to pass the address the signed and
encrypted secure boot monitor image to the authentication API.
For backward compatibility with other K2 devices and K2G GP,
the mon_install API still supports a single argument. In this case
the second argument is set to 0 by u-boot and is ignored by ROM
Andrew F. Davis [Mon, 17 Jul 2017 17:59:14 +0000 (12:59 -0500)]
configs: k2x_evm: Reorder default boot command
We first split the CONFIG_BOOTCOMMAND into its components to improve
readability. We then make the following order changes:
- Run findfdt first so the fdt name can be used in envboot like OMAP
- Install the boot monitor before running the PMMC so we can make any
needed secure changes before PMMC, do this on both HS and non-HS
- Move set_name_pmmc to just before get_pmmc_${boot}
Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
configs: k2x_evm: Adds environment variables for secure devices
Updates the default u-boot environment variables to support secure
boot. On secure devices, a secure boot monitor (sec-bm) needs to
be installed by u-boot.
Signed-off-by: Madan Srinivas <madans@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
board_is*("rev", board_ti_get_rev()) uses strncmp() for
revison detection and assumes it is success if return value
is <= 0. This will fail in case of multiple versions, as
revb will be true for board_is_*revb() and board_is_*reva().
Fix it by looking for exact match of the string.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Mon, 24 Jul 2017 03:19:40 +0000 (21:19 -0600)]
env: Move help from README to Kconfig
The CONFIG_ENV_IS_IN_... options which have already been converted to
Kconfig only have a small amount of help. Move the rest of it over from
the README.
Simon Glass [Mon, 24 Jul 2017 03:19:39 +0000 (21:19 -0600)]
Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig
This converts the following to Kconfig:
CONFIG_ENV_IS_IN_MMC
CONFIG_ENV_IS_IN_NAND
CONFIG_ENV_IS_IN_UBI
CONFIG_ENV_IS_NOWHERE
In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.
In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.
There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with
./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC
And then manual updates. This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Sat, 22 Jul 2017 22:36:16 +0000 (18:36 -0400)]
configs: Migrate RBTREE, LZO, CMD_MTDPARTS, CMD_UBI and CMD_UBIFS
The above CONFIG options are in Kconfig, and now have correct depends and
inter-dependencies. Migrate these to configs/ from include/configs/. In the
case of CMD_UBIFS also change it to be a default y if CMD_UBI.
Karl Beldan [Wed, 12 Jul 2017 16:11:47 +0000 (16:11 +0000)]
cmd: Kconfig: Fix CMD_UBIFS dependencies
Remove the ARCH_SUNXI and RBTREE dependencies.
CMD_UBIFS already gets RBTREE from CMD_UBI (from MTD_UBI), and should
the first become independant from the latter, there would likely be a
dependency on MTD_UBI anyway.
Cc: Boris Brezillon <boris.brezillon@free-electrons.com> Cc: Jagan Teki <jagan@openedev.com> Signed-off-by: Karl Beldan <karl.beldan-ext@sagemcom.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Karl Beldan [Wed, 12 Jul 2017 16:11:44 +0000 (16:11 +0000)]
cmd: Kconfig: Fix a dependency of CMD_MTDPARTS
Remove the ARCH_SUNXI dependency.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Jagan Teki <jagan@openedev.com> Signed-off-by: Karl Beldan <karl.beldan-ext@sagemcom.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Karl Beldan [Wed, 12 Jul 2017 16:11:43 +0000 (16:11 +0000)]
ubi: Kconfig: Fix MTD_UBI selection dependency
Remove the ARCH_SUNXI dependency on selection of RBTREE.
Cc: Boris Brezillon <boris.brezillon@free-electrons.com> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Jagan Teki <jagan@openedev.com> Signed-off-by: Karl Beldan <karl.beldan-ext@sagemcom.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Stefan Roese [Fri, 14 Jul 2017 15:25:54 +0000 (17:25 +0200)]
serial: ns16550: Add RX interrupt buffer support
Pasting longer lines into the U-Boot console prompt sometimes leads to
characters missing. One problem here is the small 16-byte FIFO of the
legacy NS16550 UART, e.g. on x86 platforms.
This patch now introduces a Kconfig option to enable RX interrupt
buffer support for NS16550 style UARTs. With this option enabled, I was
able paste really long lines into the U-Boot console, without any
characters missing.
Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com>
[trini: Guard ns16550_serial_remove with
CONFIG_IS_ENABLED(SERIAL_PRESENT) to match struct assignment] Signed-off-by: Tom Rini <trini@konsulko.com>
Adam Ford [Fri, 14 Jul 2017 13:53:20 +0000 (08:53 -0500)]
arm: omap3: Detect boot mode very early
Fixes 4bd754d8abef ("arm: omap: Detect boot mode very early") where
the intent was to store the boot params information in a known
location and pass it to SPL very early. Unfortunately it didn't
account for OMAP3 boards.
This patch adds adds this functionality back into OMAP3 boards.
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Adam Ford <aford173@gmail.com>
Add missing .h and add missing declarations in .h
Declare local functions as static. Make interrupt_init_cpu function
signatures consistent with how decrementer_count is declared.
Based on warnings reported by 'make C=2'
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[trini: drop cpu_init_f as 8xx/83xx are different from the rest, rework
interrupt_init_cpu/decrementer_count] Signed-off-by: Tom Rini <trini@konsulko.com>
reginfo command is calling mpc8xx_reginfo(), mpc85xx_reginfo()
or mpc86xx_reginfo() based on CONFIG_ symbol.
As those 3 functions can't me defined at the same time, let's
rename them print_reginfo() to avoid the #ifdefs
The name is kept generic as it is not at all dependent on
powerpc arch and any other arch could want to also print
such information.
In addition, as the Makefile compiles cmd/reginfo.c only when
CONFIG_CMD_REGINFO is set, there is no need to enclose the U_BOOT_CMD
definition inside a #ifdef CONFIG_CMD_REGINFO
Lets all remove the #ifdefs around the U_BOOT_CMD as this
file is only compiled when CONFIG_CMD_REGINFO is defined
Finally, this is a PowerPC-only command, disable it on a number of
non-PowerPC platforms.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by: Tom Rini <trini@konsulko.com>
km/ivm: allow to set locally administred MAC addresses
It is possible to flag MAC addresses as locally administred. In this
case they don't need to be unique. This is only allowed for interfaces
which have no connection to the outside. For the TEGR1 board we use
this feature.
If we rebrand the IVM and ethaddr was set previously we need to change
ethaddr. Otherwise we end up with a wrong MAC adress for the ethernet
interface.
Simon Glass [Mon, 10 Jul 2017 20:47:47 +0000 (14:47 -0600)]
RFC: moveconfig: Use toolchains from buildman
It is annoying to have to set up and maintain two sets of toolchains, one
for buildman and one for moveconfig.
Adjust moveconfig to make use to buildman's toolchains. This should make
things easier.
One missing feature is the ability to specify the toolchain on the command
line with a special environment variable, e.g. CROSS_COMPILE_ARM. I'm not
sure if that is useful, but if it is it could be implemented in buildman.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Simon Glass [Mon, 10 Jul 2017 20:47:46 +0000 (14:47 -0600)]
moveconfig: Tidy up imply flag parsing
Add an option to specify 'all' to enable all flags. Also print an error
if an unrecognised flag is used. At present it just prints usage
information which is not very helpful.
Andrew F. Davis [Mon, 10 Jul 2017 19:45:51 +0000 (14:45 -0500)]
arm: mach-omap2: fdt-common: Add OP-TEE node when firmware node is defined
If a firmware node is already present in the FDT we will fail to create
one and so fail to add our OP-TEE node, make this fixup first check for
a firmware node and then only try to add one if it is not found.
Andrew F. Davis [Mon, 10 Jul 2017 19:45:49 +0000 (14:45 -0500)]
arm: mach-omap2: Move omap5/sec-fxns.c into sec-common.c
TEE loading and firewall setup are common to all omap2 devices, move
these function out of omap5 and into mach-omap2. This allows us
to use these functions from other omap class devices.
Philipp Tomsich [Wed, 5 Jul 2017 15:30:40 +0000 (17:30 +0200)]
Makefile: add dependencies to regenerate u-boot.cfg when lost
When running a 'make clean' or carelessly removing u-boot.cfg, all
future make invocations (until autoconf is regenerated) will print
an error for a missing u-boot.cfg due to missing rules and dependencies.
This commit adds (i) an explicit rule dependency from all (which will
invokes the configuration checker) to cfg, and (b) adds a rule to
invoke scripts/Makefile.autoconf to regenerate u-boot.cfg.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Bin Meng <bmeng.cn@gmail.com>
Emmanuel Vadot [Sun, 25 Jun 2017 07:43:33 +0000 (09:43 +0200)]
dtc: mkimage: Add the possibility to specify DTC
FreeBSD recently switch to it's BSDL dtc. While it support most of the
features of the GPL one it still lacks the incbin directive.
Add the possibility to specify which dtc we want to use for compiling dts
and generating fit image.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com> Acked-by: Simon Glass <sjg@chromium.org>
The Odroid C2 has two GiB of memory with two reserved regions.
reg = <0x0 0x0 0x0 0x1000000>;
reg = <0x0 0x10000000 0x0 0x200000>;
Patch bfcef28ae4cf (arm: add initial support for Amlogic Meson and
ODROID-C2) provided function dram_init_banksize to reserve the
first 16 MiB of RAM for firmware in function dram_init_banksize
in arch/arm/mach-meson/board.c and defined
CONFIG_NR_DRAM_BANKS = 1.
With this patch dram_init_banksize is changed to additionally
reserve the 2MiB region for the ARM Trusted Firmware (BL31).
CONFIG_NR_DRAM_BANKS is set to 2.
Cc: Andreas Färber <afaerber@suse.de> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Fiach Antaw [Wed, 25 Jan 2017 08:53:12 +0000 (18:53 +1000)]
env: Switch env_nand, env_mmc and env_ubi to env_import_redund
The env_nand, env_mmc and env_ubi implementations all implement
redundancy using an identical serial-number scheme. This commit
migrates them to use the implementation in env_common, which is
functionally identical.
Signed-off-by: Fiach Antaw <fiach.antaw@uqconnect.edu.au> Reviewed-by: Tom Rini <trini@konsulko.com>
All current environments that implement redundancy use almost
identical implementations. This patch implements the env_nand
implementation as a function in env_common, and updates the
env_export function to export an env_nand-style 'flags' field by
default.
Signed-off-by: Fiach Antaw <fiach.antaw@uqconnect.edu.au> Reviewed-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 29 Aug 2016 13:57:01 +0000 (09:57 -0400)]
tests: test_dfu.py: Add example udev rule for host_usb_dev_node
If one does not already have a rule to create a custom device node when
a given device enumerates it can be useful to have udev create a
bus path based node to the entry in /dev/bus/usb that was just
enumerated. Given that DFU itself does not require a /dev entry it is a
good idea to provide a rule that will generate one.
Masahiro Yamada [Thu, 22 Jun 2017 08:58:09 +0000 (17:58 +0900)]
mmc: cadence: use fdt32_t for DT property value to fix sparse warning
DTB is encoded in big endian. When we retrieve property values,
we need to use fdt32_to_cpu (aka be32_to_cpu) for endian conversion.
This is a bit error-prone, but sparse is useful to detect endian
mismatch.
We need to use (fdt32_t *) instead of (u32 *) for a pointer of a
property value. Otherwise sparse warns "cast to restricted __be32".
Move CONFIG_CMD_SATA option to Kconfig to fix the following build
error:
In file included from include/configs/mx6cuboxi.h:137:0,
from include/config.h:7,
from include/common.h:21,
from common/env_common.c:11:
include/config_distro_bootcmd.h:161:2: error: expected '}' before 'BOOT_TARGET_DEVICES_references_SATA_without_CONFIG_SATA'
BOOT_TARGET_DEVICES_references_SATA_without_CONFIG_SATA
Since commit ce412b79e7255770 ("drivers: net: phy: atheros: add separate
config for AR8031") Ethernet does not work on mx6sabreauto.
This commit correctly assigns ar8031_config() as the configuration
function for AR8031 in the same way as done in the Linux kernel.
However, on mx6sabreauto design we need some additional configurations,
such as enabling the 125 MHz AR8031 output and setting the TX clock
delay that need to be done in the board file.
This is the equivalent fix from commit 4b6035da482c ("mx6sabresd: Make
Ethernet functional again").
warp can run different kernel versions, such as NXP 4.1 or
mainline.
Currently the rootfs location is passed via mmcblk number and the
problem with this approach is that the mmcblk number for the eMMC
changes depending on the kernel version.
In order to avoid such issue, use UUID method to specify the rootfs
location.
Succesfully tested booting a NXP 4.1 and also a mainline 4.12 kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
embestmx6boards: Use PARTUUID to specify the rootfs location
Currently the rootfs location is passed via mmcblk number and the
problem with this approach is that the mmcblk number for the eMMC
changes depending on the kernel version.
In order to avoid such issue, use UUID method to specify the rootfs
location.
Also add CONFIG_BOOTCOMMAND to run finduuid function and distro_bootcmd.
projects / u-boot / log