Helmut Raiger [Wed, 11 Jan 2012 03:59:22 +0000 (03:59 +0000)]
mmc: access mxcmmc from mx31 boards
This patch modifies mxcmmc.c to be used
not only by i.MX27 but also by i.MX31 boards.
Both use the same SD controller, but have different
clock set-ups.
The i.MX27 imx_get_XXXclock functions are made static to
generic.c and a public mxc_get_clock() function
is provided. Pins, base address and prototypes for
an i.MX31 specific board_init_mmc() are provided.
Some of the i.MX27 clock getters are unused and marked
as such to avoid warnings (./MAKEALL -s mx27), but
the code was left in for future use.
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at> Acked-by: Stefano Babic <sbabic@denx.de>
Jason Liu [Thu, 12 Jan 2012 22:56:16 +0000 (22:56 +0000)]
i.mx6q: mx6qsabrelite: Add the ethernet function support
Signed-off-by: Jason Liu <jason.hui@linaro.org> Signed-off-by: Eric Miao <eric.miao@linaro.org> CC: Jason Liu <jason.hui@linaro.org> CC: Stefano Babic <sbabic@denx.de>
Note: This requires that the kernel has CONFIG_HIGHMEM enabled.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> CC: Jason Liu <jason.hui@linaro.org> CC: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <jason.hui@linaro.org>
Troy Kisky [Thu, 12 Jan 2012 23:49:25 +0000 (23:49 +0000)]
i.mx6q: mx6qsabrelite: Setup uart1 pinmux
This allows the Linux kernel to use UART1 before pinmux
support is added for UART1
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> CC: Troy Kisky <troy.kisky@boundarydevices.com> CC: Jason Liu <jason.hui@linaro.org> CC: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <jason.hui@linaro.org>
Troy Kisky [Thu, 12 Jan 2012 23:49:23 +0000 (23:49 +0000)]
i.mx6: mx6x_pins: Fix uart txd definitions
The uart txd pad can also provide the rxd function. But it does not stop its
tx role. This could be used for a half duplex serial port.
Change names to reduce confusion.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> CC: Troy Kisky <troy.kisky@boundarydevices.com> CC: Jason Liu <jason.hui@linaro.org> CC: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <jason.hui@linaro.org>
Dirk Behme [Wed, 11 Jan 2012 23:28:32 +0000 (23:28 +0000)]
imximage: Sort bootops alphabetically
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> CC: Fabio Estevam <festevam@gmail.com> CC: Stefano Babic <sbabic@denx.de> CC: Jason Liu <jason.hui@linaro.org> Acked-by: Jason Liu <jason.hui@linaro.org>
Dirk Behme [Wed, 11 Jan 2012 23:28:31 +0000 (23:28 +0000)]
imximage: Add support for i.MX6
The i.MX6 processor can boot from NOR flash and SATA disks,
additionally. Add the flash offsets for these additional
boot modes.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> Signed-off-by: Fabio Estevam <festevam@gmail.com> CC: Stefano Babic <sbabic@denx.de> CC: Jason Liu <jason.hui@linaro.org> Acked-by: Jason Liu <jason.hui@linaro.org>
Since commit 97039ab98 (env_mmc: Allow board code to override the environment address)
mmc_get_env_addr is a weak-aliased function in common/env_mmc.c
The mmc_get_env_addr implementation that exists at
board/freescale/common/sdhc_boot.c is meant to be used only for PowerPC boards,
but currently it is being used for all platforms that have CONFIG_ENV_IS_IN_MMC defined.
Introduce CONFIG_FSL_FIXED_MMC_LOCATION so that the boards that need to use
the mmc_get_env_addr version from board/freescale/common/sdhc_boot.c could activate
this config option on their board file.
This fixes the retrieval of CONFIG_ENV_OFFSET on non-PowerPC boards.
Heiko Schocher [Mon, 16 Jan 2012 21:20:09 +0000 (21:20 +0000)]
arm, davinci: cam_enc_4xx board updates
- CONFIG_SYS_MMC_ENV_DEV, needed if environment on mmc
- wait for 1 second timer in board_late_init() only, if
timer is running.
- add UBI/UBIFS support
- add FIT images support
- menu support
- U-Boot max size now 0xa0000
- SPL now Block 0 page 0
- new MTD partitioning
0x00000000 SPL
0x00020000 UBL-Header
0x00040000 UBL-Header
0x00060000 UBL-Header
0x00080000 UBoot (0xa0000(U-Boot length) + 0x60000(3 spare blocks))
0x00180000 ENV- Variablen (1)
0x001a0000 ENV- Variablen (2)
0x001c0000 ENV- Variablen (reserved for Bad Block)
0x001e0000 ENV- Variablen (reserved for Bad Block)
0x00200000 UBI-Device
UBI Volumes:
„default“: contain environment-default values
„rootfs1“: UBIFS root-fs (1); contain linux kernel image
„rootfs2“: UBIFS root-fs (2); contain linux kernel image
„data-ro“: UBIFS data (read only)
„data-rw“: UBIFS data (read/write)
- new environment variables:
- app_reset
(this is only passed per cmdline to linux)
- dvn_app_vers
string from ramdisk description contained in the
FIT image
- dvn_boot_vers
string from ubootimage description contained in the
FIT image
- saveparms, restoreparms, restoretmpparms, savetmpparms
helper for saving network parameter.
- ubiargs
set ubi kernel cmdlinargs for booting with a ubifs rootfs
- ubi_ubi boot with reading kernel image from ubifs, and
use a ubifs as rootfs
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Sandeep Paulraj <s-paulraj@ti.com> Cc: Tom Rini <tom.rini@gmail.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Wolfgang Denk <wd@denx.de>
Heiko Schocher [Sat, 14 Jan 2012 21:42:46 +0000 (21:42 +0000)]
arm, davinci: add workaround for not resetting DMA bus and VPSS modules
The Buffer Logic of VPSS is Not Reset by System Reset Pin, see
http://www.ti.com/lit/er/sprz316b/sprz316b.pdf chapter Advisory 1.2.1
on page 9. Add workaroundcode proposed in the errata.
OMAP SPL: Fix missing timer_init() call in OMAP4 s_init()
In 8775471bb, the call to timer_init() was removed from common code
and put in OMAP3 s_init() function. As a result the boot was broken
on OMAP4. This patch adds timer_init() in OMAP4 s_init(), that fix
boot on all OMAP4 boards.
Signed-off-by: Nicolas Dechesne <n-dechesne@ti.com> Tested-by: Robert P. J. Day <rpjday@crashcourse.ca> Cc: Sandeep Paulraj <s-paulraj@ti.com> Cc: Tom Rini <trini@ti.com>
Tom Rini [Wed, 18 Jan 2012 08:28:50 +0000 (08:28 +0000)]
OMAP3: Correct get_sdr_cs_offset mask
The function get_sdr_cs_offset reads the CS_CFG register in the SDRC
to determine where CS1 is mapped to. make_cs1_contiguous() will set
CS1 to follow after CS0. The CS_CFG register has values in bits 9:8
and 3:0 but we had erroneously been testing 5:4 and 3:0 resulting in
incorrect offsets on platforms with less than 128MB as 3:0 describe
128MB hunks and 9:8 describe 32MB offsets after the 128MB hunk.
Tested-by: Grant Erickson <marathon96@gmail.com> Signed-off-by: Tom Rini <trini@ti.com>
Pali Rohár [Tue, 24 Jan 2012 04:27:58 +0000 (04:27 +0000)]
arm: omap3: Define save_boot_params in lowlevel_init.S for SPL only
Wrap the function save_boot_params with CONFIG_SPL_BUILD. This will
allow non-SPL boards to define their own save_boot_params functions
in U-Boot itself.
Simon Glass [Mon, 9 Jan 2012 13:22:15 +0000 (13:22 +0000)]
tegra2: Enable data cache
This enables the data cache on Tegra2 boards.
As discussed on the list, this is better off in the Tegra2 cpu code than in a
particular vendor directory. We should be safe turning on the cache for all
Tegra2 boards.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Mon, 9 Jan 2012 13:20:40 +0000 (13:20 +0000)]
tegra: mmc: Support operation with dcache enabled
When the data cache is enabled we must flush on write and invalidate
on read. We also check that buffers are aligned to data cache lines
boundaries. With recent work in U-Boot this should generally be the case
but the warnings will catch problems.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Wed, 11 Jan 2012 12:42:25 +0000 (12:42 +0000)]
tegra: Add SDMMC support to funcmux
This adds support for SDMMC ports to the funcmux. Only one
option is supported: FUNCMUXO_SDMMC_8BIT which selects an 8-bit
wide SDIO interface where available.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Wed, 11 Jan 2012 12:42:23 +0000 (12:42 +0000)]
tegra: Add enum to select from available funcmux configs
We want to give a name to each available funcmux config. For now we just
use the pin group names (even through it is verbose) since there seems
to be nothing better.
Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Fri, 6 Jan 2012 12:14:42 +0000 (12:14 +0000)]
tegra2: Add support for Compal Paz00 (Toshiba AC100)
The Toshiba AC100 (Compal code-name Paz00, aka Dynabook AZ) is a netbook
derived from the NVIDIA Tegra Harmony reference board. It ships with
Android, but is often repurposed to run Linux. This patch adds just enough
support to get a U-Boot serial console, and the ability access built-in
eMMC and the external SD slot.
v2:
* Rebased on latest HEAD, incorporated changes made to other board files.
* Moved board files from board/nvidia to board/compal.
* Switched to correct odmdata value. This required add the previous patch
to fix U-Boot's interpretation of the odmdata RAM size field.
* Removed nvmem= from default Linux kernel command-line; no drivers use the
reserved memory yet, so there's no point reserving it.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Fri, 6 Jan 2012 12:14:40 +0000 (12:14 +0000)]
tegra2: Fix conflicting pinmux for UARTA
Tegra appears to boot with function UARTA pre-selected on mux
group SDB. If two mux groups are both set to the same function,
it's unclear which group's pins drive the RX signals into the
HW module. For UARTA, SDB certainly overrides group IRTX in
practice. To solve this, configure some alternative function on
SDB to avoid the conflict. Also, tri-state the group to avoid
driving any signal onto it until we know what's connected.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Wolfgang Denk [Sat, 11 Feb 2012 21:14:56 +0000 (22:14 +0100)]
Merge branch 'master' of /home/wd/git/u-boot/custodians
* 'master' of /home/wd/git/u-boot/custodians:
nand/fsl_elbc: Convert to self-init
nand: Introduce CONFIG_SYS_NAND_SELF_INIT
nand_spl: store ecc data on the stack
mtd/nand: Add ONFI support for FSL NAND controller
nand: make 1-bit software ECC configurable
nand: Sanitize ONFI strings.
nand: Merge changes to BBT from Linux nand driver
nand: Merge changes from Linux nand driver
nand: cleanup whitespace
nand: Add more NAND types from Linux nand driver
nand: Merge BCH code from Linux nand driver
NAND: Remove additional (CONFIG_SYS)_NAND_MAX_CHIPS
NAND: remove NAND_MAX_CHIPS definitions
nand_spl_simple: store ecc data on the stack
Wolfgang Denk [Sat, 11 Feb 2012 21:07:48 +0000 (22:07 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-nand-flash
* 'master' of git://git.denx.de/u-boot-nand-flash:
nand/fsl_elbc: Convert to self-init
nand: Introduce CONFIG_SYS_NAND_SELF_INIT
nand_spl: store ecc data on the stack
mtd/nand: Add ONFI support for FSL NAND controller
nand: make 1-bit software ECC configurable
nand: Sanitize ONFI strings.
nand: Merge changes to BBT from Linux nand driver
nand: Merge changes from Linux nand driver
nand: cleanup whitespace
nand: Add more NAND types from Linux nand driver
nand: Merge BCH code from Linux nand driver
NAND: Remove additional (CONFIG_SYS)_NAND_MAX_CHIPS
NAND: remove NAND_MAX_CHIPS definitions
nand_spl_simple: store ecc data on the stack
Wolfgang Denk [Sat, 11 Feb 2012 21:05:13 +0000 (22:05 +0100)]
Merge branch 'master' of /home/wd/git/u-boot/custodians
* 'master' of /home/wd/git/u-boot/custodians:
ARM: AM33XX: Add i2c support
ARM: AM33XX: Add AM33XX I2C driver support
ARM: I2C: I2C Multi byte address support
* Fix: watchdog timed out, if flash blank (0xFF) blocks
The current implementation of cfi_flash uses udelay to reset watchdog.
If several blocks are blank (0xff filled) the watchdog timed out.
The reason is, udelay is never called, if flash device is ready to fast.
e.g.
mw.w $(copy_addr) FFFF 10000;cp.b $(copy_addr) 10880000 20000
Scott Wood [Fri, 13 Jan 2012 01:42:58 +0000 (19:42 -0600)]
nand/fsl_elbc: Convert to self-init
This driver doesn't yet make use of the added flexibility (not that that
should stop anyone from converting...), but it will with the in-progress
hack to support 4k-page NAND.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Scott Wood [Fri, 13 Jan 2012 01:07:23 +0000 (19:07 -0600)]
nand: Introduce CONFIG_SYS_NAND_SELF_INIT
This allows a driver to run code between nand_scan_ident() and
nand_scan_tail(), among other things. See the additions to
doc/README.nand for details.
To allow a gradual transition, Boards that don't set
CONFIG_SYS_NAND_SELF_INIT will still be initialized the old way, but
new drivers should not require this, and existing drivers should be
converted when convenient.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Currently nand_spl_simple puts it's temp data at 0x10000 offset in SDRAM
which is likely to contain already loaded data.
The patch saves the oob data and the ecc on the stack replacing
the fixed address in RAM.
Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Ilya Yanok <yanok@emcraft.com> CC: Scott Wood <scottwood@freescale.com> CC: Tom Rini <tom.rini@gmail.com> CC: Simon Schwarz <simonschwarzcor@googlemail.com> CC: Wolfgang Denk <wd@denx.de> Signed-off-by: Scott Wood <scottwood@freescale.com>
While nand_spl is on its way out, in favor of spl, there are still
many boards using it, and conversions are gradual. This allows us
to get rid of CONFIG_SYS_NAND_ECCSTEPS and CONFIG_SYS_NAND_ECCTOTAL now,
which would otherwise be likely to linger unreferenced after a conversion.
It also eliminates a temporary error in the hawkboard_nand build, since
the spl version of the patch removed ECCSTEPS/TOTAL from hawkboard.h, but
the spl conversion is pending (and may be merged via a different tree).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Christian Hitz [Wed, 12 Oct 2011 07:32:06 +0000 (09:32 +0200)]
nand: make 1-bit software ECC configurable
The software ECC algorithm is not necessary when hardware ECC
is available and can be left out for a smaller image size.
Enable with CONFIG_MTD_ECC_SOFT.
Signed-off-by: Christian Hitz <christian.hitz@aizo.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch synchronizes the nand driver with the Linux 3.0 state.
Signed-off-by: Christian Hitz <christian.hitz@aizo.com> Cc: Scott Wood <scottwood@freescale.com>
[scottwood@freescale.com: minor fixes] Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch merges the BCH ECC algorithm from the 3.0 Linux kernel.
This enables U-Boot to support modern NAND flash chips that
require more than 1-bit of ECC in software.
Signed-off-by: Christian Hitz <christian.hitz@aizo.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
This change follows the change by Wolfgang Grandegger (commit 6c869637fef),
which allows to remove useless NAND_MAX_CHIPS definitions in board config
files.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
Stefano Babic [Thu, 15 Dec 2011 09:55:37 +0000 (10:55 +0100)]
nand_spl_simple: store ecc data on the stack
Currently nand_spl_simple puts it's temp data at 0x10000 offset in SDRAM
which is likely to contain already loaded data.
The patch saves the oob data and the ecc on the stack replacing
the fixed address in RAM.
Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Ilya Yanok <yanok@emcraft.com> CC: Scott Wood <scottwood@freescale.com> CC: Tom Rini <tom.rini@gmail.com> CC: Simon Schwarz <simonschwarzcor@googlemail.com> CC: Wolfgang Denk <wd@denx.de> Signed-off-by: Scott Wood <scottwood@freescale.com>
Andreas Müller [Wed, 4 Jan 2012 15:26:25 +0000 (15:26 +0000)]
overo: add SPL support
* implementation based on ti beagleboard/omap3evm
* timing data and i2c workaround for revision 0 boards taken from x-loader
* run-tested with overo revision 0 and 1 / boot from NAND and SDcard
* run-tested with x-loader
Signed-off-by: Andreas Müller <schnitzeltony@gmx.de> Signed-off-by: Tom Rini <trini@ti.com>
Andreas Müller [Wed, 4 Jan 2012 15:26:22 +0000 (15:26 +0000)]
drivers/i2c/omap24xx_i2c.c: move all local variables to SRAM
At old overo boards TWL4030 RTC irq is connected to gpio112. Unfortunately
this pin is also used for revision detection. Therefore we need to send
shut-up to TWL4030 to avoid reading wrong revision. In SPL this must
be done before SDRAM is set up because the type of SDRAM is revision dependent.
By this patch it is ensured that all variables used by omap24xx_i2c.c are
located in SRAM.
Signed-off-by: Andreas Müller <schnitzeltony@gmx.de> Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
Chandan Nath [Mon, 9 Jan 2012 20:38:59 +0000 (20:38 +0000)]
ARM:AM33XX: Add SPL support for AM335X EVM
This patch is added to support SPL feature on AM335X
platform. In this patch, MMC1 is configured as boot
device for SPL and support for other devices will be
added in the next patch series.
Signed-off-by: Chandan Nath <chandan.nath@ti.com> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Nikita Kiryanov [Thu, 5 Jan 2012 02:03:22 +0000 (02:03 +0000)]
omap3: make get_board_rev() function weak
Current get_board_rev() function returns a hard coded value which is
obviously incorrect for the majority of boards.
Allow boards to provide a correct implementation by making this function
weak.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Nikita Kiryanov [Mon, 2 Jan 2012 04:01:31 +0000 (04:01 +0000)]
cm-t35: various cleanups
Move #ifdef CONFIG_SMC911X out of board_eth_init() function,
simplify the board_mmc_init() function, and enclose handle_mac_address()
in the CONFIG_SMC911X.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Peter Barada [Mon, 19 Dec 2011 19:54:51 +0000 (19:54 +0000)]
ARMV7: Add support For Logic OMAP35x/DM37x modules
This patch adds basic support for OMAP35x/DM37x SOM LV/Torpedo
reference boards. It assumes U-boot is loaded to SDRAM with the
help of another small bootloader (x-load) running from SRAM.
Signed-off-by: Peter Barada <peter.barada@logicpd.com> Cc: Tom Rini <tom.rini@gmail.com> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Christian Riesch [Thu, 15 Dec 2011 00:33:21 +0000 (00:33 +0000)]
da850evm: Remove CONFIG_SYS_xxCACHE_OFF defines
This patch removes the defines CONFIG_SYS_ICACHE_OFF,
CONFIG_SYS_DCACHE_OFF, and CONFIG_SYS_L2CACHE_OFF from the board
configuration. These defines are useless since cache is
anyway disabled for the entire architecture since commit cba4b1809f043bf85c806e5a4e342f62bd5ded45.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Tom Rini <trini@ti.com>
Christian Riesch [Thu, 15 Dec 2011 06:21:55 +0000 (06:21 +0000)]
arm, davinci: Use a common configuration file for da850evm and da850_am18xxevm
In commit 06194b6b65f701a9d6ef2d9b4123c4afe57d8783 a separate header
file was introduced for the AM1808 EVM, include/configs/da850_am18xxevm.h.
Before this commit, the da850evm.h configuration file was used for both
the AM1808 and the OMAP-L138 EVMs. The only substantial difference
between the da850evm and the da850_am18xxevm configuration is a single
bit in the hardware revision that is passed to the Linux kernel.
This patch removes include/configs/da850_am18xxevm.h. Instead the
include/configs/da850evm.h configuration is used for AM18xx EVMs and
CONFIG_DA850_AM18X_EVM is defined in boards.cfg.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at> Cc: Tom Rini <trini@ti.com>
Zach Sadecki [Mon, 9 Jan 2012 10:22:54 +0000 (10:22 +0000)]
mx28: fix clearing of IRQs in power init
There are 2 locations in the power init code for the mx28 where IRQs are not being cleared because incorrect methods to clear those bits were being used. This was causing my board to get stuck waiting for POWER_CTRL_VDD5V_DROOP_IRQ to clear. Using the correct method to clear the IRQs fixes it.
Signed-off-by: Zach Sadecki <zach@itwatchdogs.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Marek Vasut <marek.vasut@gmail.com>
projects / u-boot / log