[freertos] / FreeRTOS / Demo / CORTEX_A53_64-bit_UltraScale_MPSoC / ZynqMP_hw_platform / psu_init.tcl

#****************************************************************************
###
#
# @file psu_init.tcl
#
# This file is automatically generated
#
#****************************************************************************
set psu_pll_init_data {
                # : RPLL INIT
                # Register : RPLL_CFG @ 0XFF5E0034</p>

                # PLL loop filter resistor control
                # PSU_CRL_APB_RPLL_CFG_RES                                                        0x2

                # PLL charge pump control
                # PSU_CRL_APB_RPLL_CFG_CP                                                         0x3

                # PLL loop filter high frequency capacitor control
                # PSU_CRL_APB_RPLL_CFG_LFHF                                                       0x3

                # Lock circuit counter setting
                # PSU_CRL_APB_RPLL_CFG_LOCK_CNT                                                   0x258

                # Lock circuit configuration settings for lock windowsize
                # PSU_CRL_APB_RPLL_CFG_LOCK_DLY                                                   0x3f

                # Helper data. Values are to be looked up in a table from Data Sheet
                #(OFFSET, MASK, VALUE)      (0XFF5E0034, 0xFE7FEDEFU ,0x7E4B0C62U)  */
    mask_write 0XFF5E0034 0xFE7FEDEF 0x7E4B0C62
                # : UPDATE FB_DIV
                # Register : RPLL_CTRL @ 0XFF5E0030</p>

                # Mux select for determining which clock feeds this PLL. 0XX pss_ref_clk is the source 100 video clk is the source 101 pss_alt_
                # ef_clk is the source 110 aux_refclk[X] is the source 111 gt_crx_ref_clk is the source
                # PSU_CRL_APB_RPLL_CTRL_PRE_SRC                                                   0x0

                # The integer portion of the feedback divider to the PLL
                # PSU_CRL_APB_RPLL_CTRL_FBDIV                                                     0x48

                # This turns on the divide by 2 that is inside of the PLL. This does not change the VCO frequency, just the output frequency
                # PSU_CRL_APB_RPLL_CTRL_DIV2                                                      0x1

                # PLL Basic Control
                #(OFFSET, MASK, VALUE)      (0XFF5E0030, 0x00717F00U ,0x00014800U)  */
    mask_write 0XFF5E0030 0x00717F00 0x00014800
                # : BY PASS PLL
                # Register : RPLL_CTRL @ 0XFF5E0030</p>

                # Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4
                # cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_RPLL_CTRL_BYPASS                                                    1

                # PLL Basic Control
                #(OFFSET, MASK, VALUE)      (0XFF5E0030, 0x00000008U ,0x00000008U)  */
    mask_write 0XFF5E0030 0x00000008 0x00000008
                # : ASSERT RESET
                # Register : RPLL_CTRL @ 0XFF5E0030</p>

                # Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS.
                # PSU_CRL_APB_RPLL_CTRL_RESET                                                     1

                # PLL Basic Control
                #(OFFSET, MASK, VALUE)      (0XFF5E0030, 0x00000001U ,0x00000001U)  */
    mask_write 0XFF5E0030 0x00000001 0x00000001
                # : DEASSERT RESET
                # Register : RPLL_CTRL @ 0XFF5E0030</p>

                # Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS.
                # PSU_CRL_APB_RPLL_CTRL_RESET                                                     0

                # PLL Basic Control
                #(OFFSET, MASK, VALUE)      (0XFF5E0030, 0x00000001U ,0x00000000U)  */
    mask_write 0XFF5E0030 0x00000001 0x00000000
                # : CHECK PLL STATUS
                # Register : PLL_STATUS @ 0XFF5E0040</p>

                # RPLL is locked
                # PSU_CRL_APB_PLL_STATUS_RPLL_LOCK                                                1
    mask_poll 0XFF5E0040 0x00000002
                # : REMOVE PLL BY PASS
                # Register : RPLL_CTRL @ 0XFF5E0030</p>

                # Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4
                # cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_RPLL_CTRL_BYPASS                                                    0

                # PLL Basic Control
                #(OFFSET, MASK, VALUE)      (0XFF5E0030, 0x00000008U ,0x00000000U)  */
    mask_write 0XFF5E0030 0x00000008 0x00000000
                # Register : RPLL_TO_FPD_CTRL @ 0XFF5E0048</p>

                # Divisor value for this clock.
                # PSU_CRL_APB_RPLL_TO_FPD_CTRL_DIVISOR0                                           0x3

                # Control for a clock that will be generated in the LPD, but used in the FPD as a clock source for the peripheral clock muxes.
                #(OFFSET, MASK, VALUE)      (0XFF5E0048, 0x00003F00U ,0x00000300U)  */
    mask_write 0XFF5E0048 0x00003F00 0x00000300
                # : RPLL FRAC CFG
                # Register : RPLL_FRAC_CFG @ 0XFF5E0038</p>

                # Fractional SDM bypass control. When 0, PLL is in integer mode and it ignores all fractional data. When 1, PLL is in fractiona
                #  mode and uses DATA of this register for the fractional portion of the feedback divider.
                # PSU_CRL_APB_RPLL_FRAC_CFG_ENABLED                                               0x0

                # Fractional value for the Feedback value.
                # PSU_CRL_APB_RPLL_FRAC_CFG_DATA                                                  0x0

                # Fractional control for the PLL
                #(OFFSET, MASK, VALUE)      (0XFF5E0038, 0x8000FFFFU ,0x00000000U)  */
    mask_write 0XFF5E0038 0x8000FFFF 0x00000000
                # : IOPLL INIT
                # Register : IOPLL_CFG @ 0XFF5E0024</p>

                # PLL loop filter resistor control
                # PSU_CRL_APB_IOPLL_CFG_RES                                                       0xc

                # PLL charge pump control
                # PSU_CRL_APB_IOPLL_CFG_CP                                                        0x3

                # PLL loop filter high frequency capacitor control
                # PSU_CRL_APB_IOPLL_CFG_LFHF                                                      0x3

                # Lock circuit counter setting
                # PSU_CRL_APB_IOPLL_CFG_LOCK_CNT                                                  0x339

                # Lock circuit configuration settings for lock windowsize
                # PSU_CRL_APB_IOPLL_CFG_LOCK_DLY                                                  0x3f

                # Helper data. Values are to be looked up in a table from Data Sheet
                #(OFFSET, MASK, VALUE)      (0XFF5E0024, 0xFE7FEDEFU ,0x7E672C6CU)  */
    mask_write 0XFF5E0024 0xFE7FEDEF 0x7E672C6C
                # : UPDATE FB_DIV
                # Register : IOPLL_CTRL @ 0XFF5E0020</p>

                # Mux select for determining which clock feeds this PLL. 0XX pss_ref_clk is the source 100 video clk is the source 101 pss_alt_
                # ef_clk is the source 110 aux_refclk[X] is the source 111 gt_crx_ref_clk is the source
                # PSU_CRL_APB_IOPLL_CTRL_PRE_SRC                                                  0x0

                # The integer portion of the feedback divider to the PLL
                # PSU_CRL_APB_IOPLL_CTRL_FBDIV                                                    0x2d

                # This turns on the divide by 2 that is inside of the PLL. This does not change the VCO frequency, just the output frequency
                # PSU_CRL_APB_IOPLL_CTRL_DIV2                                                     0x0

                # PLL Basic Control
                #(OFFSET, MASK, VALUE)      (0XFF5E0020, 0x00717F00U ,0x00002D00U)  */
    mask_write 0XFF5E0020 0x00717F00 0x00002D00
                # : BY PASS PLL
                # Register : IOPLL_CTRL @ 0XFF5E0020</p>

                # Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4
                # cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_IOPLL_CTRL_BYPASS                                                   1

                # PLL Basic Control
                #(OFFSET, MASK, VALUE)      (0XFF5E0020, 0x00000008U ,0x00000008U)  */
    mask_write 0XFF5E0020 0x00000008 0x00000008
                # : ASSERT RESET
                # Register : IOPLL_CTRL @ 0XFF5E0020</p>

                # Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS.
                # PSU_CRL_APB_IOPLL_CTRL_RESET                                                    1

                # PLL Basic Control
                #(OFFSET, MASK, VALUE)      (0XFF5E0020, 0x00000001U ,0x00000001U)  */
    mask_write 0XFF5E0020 0x00000001 0x00000001
                # : DEASSERT RESET
                # Register : IOPLL_CTRL @ 0XFF5E0020</p>

                # Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS.
                # PSU_CRL_APB_IOPLL_CTRL_RESET                                                    0

                # PLL Basic Control
                #(OFFSET, MASK, VALUE)      (0XFF5E0020, 0x00000001U ,0x00000000U)  */
    mask_write 0XFF5E0020 0x00000001 0x00000000
                # : CHECK PLL STATUS
                # Register : PLL_STATUS @ 0XFF5E0040</p>

                # IOPLL is locked
                # PSU_CRL_APB_PLL_STATUS_IOPLL_LOCK                                               1
    mask_poll 0XFF5E0040 0x00000001
                # : REMOVE PLL BY PASS
                # Register : IOPLL_CTRL @ 0XFF5E0020</p>

                # Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4
                # cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_IOPLL_CTRL_BYPASS                                                   0

                # PLL Basic Control
                #(OFFSET, MASK, VALUE)      (0XFF5E0020, 0x00000008U ,0x00000000U)  */
    mask_write 0XFF5E0020 0x00000008 0x00000000
                # Register : IOPLL_TO_FPD_CTRL @ 0XFF5E0044</p>

                # Divisor value for this clock.
                # PSU_CRL_APB_IOPLL_TO_FPD_CTRL_DIVISOR0                                          0x3

                # Control for a clock that will be generated in the LPD, but used in the FPD as a clock source for the peripheral clock muxes.
                #(OFFSET, MASK, VALUE)      (0XFF5E0044, 0x00003F00U ,0x00000300U)  */
    mask_write 0XFF5E0044 0x00003F00 0x00000300
                # : IOPLL FRAC CFG
                # Register : IOPLL_FRAC_CFG @ 0XFF5E0028</p>

                # Fractional SDM bypass control. When 0, PLL is in integer mode and it ignores all fractional data. When 1, PLL is in fractiona
                #  mode and uses DATA of this register for the fractional portion of the feedback divider.
                # PSU_CRL_APB_IOPLL_FRAC_CFG_ENABLED                                              0x0

                # Fractional value for the Feedback value.
                # PSU_CRL_APB_IOPLL_FRAC_CFG_DATA                                                 0x0

                # Fractional control for the PLL
                #(OFFSET, MASK, VALUE)      (0XFF5E0028, 0x8000FFFFU ,0x00000000U)  */
    mask_write 0XFF5E0028 0x8000FFFF 0x00000000
                # : APU_PLL INIT
                # Register : APLL_CFG @ 0XFD1A0024</p>

                # PLL loop filter resistor control
                # PSU_CRF_APB_APLL_CFG_RES                                                        0x2

                # PLL charge pump control
                # PSU_CRF_APB_APLL_CFG_CP                                                         0x3

                # PLL loop filter high frequency capacitor control
                # PSU_CRF_APB_APLL_CFG_LFHF                                                       0x3

                # Lock circuit counter setting
                # PSU_CRF_APB_APLL_CFG_LOCK_CNT                                                   0x258

                # Lock circuit configuration settings for lock windowsize
                # PSU_CRF_APB_APLL_CFG_LOCK_DLY                                                   0x3f

                # Helper data. Values are to be looked up in a table from Data Sheet
                #(OFFSET, MASK, VALUE)      (0XFD1A0024, 0xFE7FEDEFU ,0x7E4B0C62U)  */
    mask_write 0XFD1A0024 0xFE7FEDEF 0x7E4B0C62
                # : UPDATE FB_DIV
                # Register : APLL_CTRL @ 0XFD1A0020</p>

                # Mux select for determining which clock feeds this PLL. 0XX pss_ref_clk is the source 100 video clk is the source 101 pss_alt_
                # ef_clk is the source 110 aux_refclk[X] is the source 111 gt_crx_ref_clk is the source
                # PSU_CRF_APB_APLL_CTRL_PRE_SRC                                                   0x0

                # The integer portion of the feedback divider to the PLL
                # PSU_CRF_APB_APLL_CTRL_FBDIV                                                     0x42

                # This turns on the divide by 2 that is inside of the PLL. This does not change the VCO frequency, just the output frequency
                # PSU_CRF_APB_APLL_CTRL_DIV2                                                      0x1

                # PLL Basic Control
                #(OFFSET, MASK, VALUE)      (0XFD1A0020, 0x00717F00U ,0x00014200U)  */
    mask_write 0XFD1A0020 0x00717F00 0x00014200
                # : BY PASS PLL
                # Register : APLL_CTRL @ 0XFD1A0020</p>

                # Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4
                # cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRF_APB_APLL_CTRL_BYPASS                                                    1

                # PLL Basic Control
                #(OFFSET, MASK, VALUE)      (0XFD1A0020, 0x00000008U ,0x00000008U)  */
    mask_write 0XFD1A0020 0x00000008 0x00000008
                # : ASSERT RESET
                # Register : APLL_CTRL @ 0XFD1A0020</p>

                # Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS.
                # PSU_CRF_APB_APLL_CTRL_RESET                                                     1

                # PLL Basic Control
                #(OFFSET, MASK, VALUE)      (0XFD1A0020, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD1A0020 0x00000001 0x00000001
                # : DEASSERT RESET
                # Register : APLL_CTRL @ 0XFD1A0020</p>

                # Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS.
                # PSU_CRF_APB_APLL_CTRL_RESET                                                     0

                # PLL Basic Control
                #(OFFSET, MASK, VALUE)      (0XFD1A0020, 0x00000001U ,0x00000000U)  */
    mask_write 0XFD1A0020 0x00000001 0x00000000
                # : CHECK PLL STATUS
                # Register : PLL_STATUS @ 0XFD1A0044</p>

                # APLL is locked
                # PSU_CRF_APB_PLL_STATUS_APLL_LOCK                                                1
    mask_poll 0XFD1A0044 0x00000001
                # : REMOVE PLL BY PASS
                # Register : APLL_CTRL @ 0XFD1A0020</p>

                # Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4
                # cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRF_APB_APLL_CTRL_BYPASS                                                    0

                # PLL Basic Control
                #(OFFSET, MASK, VALUE)      (0XFD1A0020, 0x00000008U ,0x00000000U)  */
    mask_write 0XFD1A0020 0x00000008 0x00000000
                # Register : APLL_TO_LPD_CTRL @ 0XFD1A0048</p>

                # Divisor value for this clock.
                # PSU_CRF_APB_APLL_TO_LPD_CTRL_DIVISOR0                                           0x3

                # Control for a clock that will be generated in the FPD, but used in the LPD as a clock source for the peripheral clock muxes.
                #(OFFSET, MASK, VALUE)      (0XFD1A0048, 0x00003F00U ,0x00000300U)  */
    mask_write 0XFD1A0048 0x00003F00 0x00000300
                # : APLL FRAC CFG
                # Register : APLL_FRAC_CFG @ 0XFD1A0028</p>

                # Fractional SDM bypass control. When 0, PLL is in integer mode and it ignores all fractional data. When 1, PLL is in fractiona
                #  mode and uses DATA of this register for the fractional portion of the feedback divider.
                # PSU_CRF_APB_APLL_FRAC_CFG_ENABLED                                               0x0

                # Fractional value for the Feedback value.
                # PSU_CRF_APB_APLL_FRAC_CFG_DATA                                                  0x0

                # Fractional control for the PLL
                #(OFFSET, MASK, VALUE)      (0XFD1A0028, 0x8000FFFFU ,0x00000000U)  */
    mask_write 0XFD1A0028 0x8000FFFF 0x00000000
                # : DDR_PLL INIT
                # Register : DPLL_CFG @ 0XFD1A0030</p>

                # PLL loop filter resistor control
                # PSU_CRF_APB_DPLL_CFG_RES                                                        0x2

                # PLL charge pump control
                # PSU_CRF_APB_DPLL_CFG_CP                                                         0x3

                # PLL loop filter high frequency capacitor control
                # PSU_CRF_APB_DPLL_CFG_LFHF                                                       0x3

                # Lock circuit counter setting
                # PSU_CRF_APB_DPLL_CFG_LOCK_CNT                                                   0x258

                # Lock circuit configuration settings for lock windowsize
                # PSU_CRF_APB_DPLL_CFG_LOCK_DLY                                                   0x3f

                # Helper data. Values are to be looked up in a table from Data Sheet
                #(OFFSET, MASK, VALUE)      (0XFD1A0030, 0xFE7FEDEFU ,0x7E4B0C62U)  */
    mask_write 0XFD1A0030 0xFE7FEDEF 0x7E4B0C62
                # : UPDATE FB_DIV
                # Register : DPLL_CTRL @ 0XFD1A002C</p>

                # Mux select for determining which clock feeds this PLL. 0XX pss_ref_clk is the source 100 video clk is the source 101 pss_alt_
                # ef_clk is the source 110 aux_refclk[X] is the source 111 gt_crx_ref_clk is the source
                # PSU_CRF_APB_DPLL_CTRL_PRE_SRC                                                   0x0

                # The integer portion of the feedback divider to the PLL
                # PSU_CRF_APB_DPLL_CTRL_FBDIV                                                     0x40

                # This turns on the divide by 2 that is inside of the PLL. This does not change the VCO frequency, just the output frequency
                # PSU_CRF_APB_DPLL_CTRL_DIV2                                                      0x1

                # PLL Basic Control
                #(OFFSET, MASK, VALUE)      (0XFD1A002C, 0x00717F00U ,0x00014000U)  */
    mask_write 0XFD1A002C 0x00717F00 0x00014000
                # : BY PASS PLL
                # Register : DPLL_CTRL @ 0XFD1A002C</p>

                # Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4
                # cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRF_APB_DPLL_CTRL_BYPASS                                                    1

                # PLL Basic Control
                #(OFFSET, MASK, VALUE)      (0XFD1A002C, 0x00000008U ,0x00000008U)  */
    mask_write 0XFD1A002C 0x00000008 0x00000008
                # : ASSERT RESET
                # Register : DPLL_CTRL @ 0XFD1A002C</p>

                # Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS.
                # PSU_CRF_APB_DPLL_CTRL_RESET                                                     1

                # PLL Basic Control
                #(OFFSET, MASK, VALUE)      (0XFD1A002C, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD1A002C 0x00000001 0x00000001
                # : DEASSERT RESET
                # Register : DPLL_CTRL @ 0XFD1A002C</p>

                # Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS.
                # PSU_CRF_APB_DPLL_CTRL_RESET                                                     0

                # PLL Basic Control
                #(OFFSET, MASK, VALUE)      (0XFD1A002C, 0x00000001U ,0x00000000U)  */
    mask_write 0XFD1A002C 0x00000001 0x00000000
                # : CHECK PLL STATUS
                # Register : PLL_STATUS @ 0XFD1A0044</p>

                # DPLL is locked
                # PSU_CRF_APB_PLL_STATUS_DPLL_LOCK                                                1
    mask_poll 0XFD1A0044 0x00000002
                # : REMOVE PLL BY PASS
                # Register : DPLL_CTRL @ 0XFD1A002C</p>

                # Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4
                # cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRF_APB_DPLL_CTRL_BYPASS                                                    0

                # PLL Basic Control
                #(OFFSET, MASK, VALUE)      (0XFD1A002C, 0x00000008U ,0x00000000U)  */
    mask_write 0XFD1A002C 0x00000008 0x00000000
                # Register : DPLL_TO_LPD_CTRL @ 0XFD1A004C</p>

                # Divisor value for this clock.
                # PSU_CRF_APB_DPLL_TO_LPD_CTRL_DIVISOR0                                           0x3

                # Control for a clock that will be generated in the FPD, but used in the LPD as a clock source for the peripheral clock muxes.
                #(OFFSET, MASK, VALUE)      (0XFD1A004C, 0x00003F00U ,0x00000300U)  */
    mask_write 0XFD1A004C 0x00003F00 0x00000300
                # : DPLL FRAC CFG
                # Register : DPLL_FRAC_CFG @ 0XFD1A0034</p>

                # Fractional SDM bypass control. When 0, PLL is in integer mode and it ignores all fractional data. When 1, PLL is in fractiona
                #  mode and uses DATA of this register for the fractional portion of the feedback divider.
                # PSU_CRF_APB_DPLL_FRAC_CFG_ENABLED                                               0x0

                # Fractional value for the Feedback value.
                # PSU_CRF_APB_DPLL_FRAC_CFG_DATA                                                  0x0

                # Fractional control for the PLL
                #(OFFSET, MASK, VALUE)      (0XFD1A0034, 0x8000FFFFU ,0x00000000U)  */
    mask_write 0XFD1A0034 0x8000FFFF 0x00000000
                # : VIDEO_PLL INIT
                # Register : VPLL_CFG @ 0XFD1A003C</p>

                # PLL loop filter resistor control
                # PSU_CRF_APB_VPLL_CFG_RES                                                        0x2

                # PLL charge pump control
                # PSU_CRF_APB_VPLL_CFG_CP                                                         0x3

                # PLL loop filter high frequency capacitor control
                # PSU_CRF_APB_VPLL_CFG_LFHF                                                       0x3

                # Lock circuit counter setting
                # PSU_CRF_APB_VPLL_CFG_LOCK_CNT                                                   0x28a

                # Lock circuit configuration settings for lock windowsize
                # PSU_CRF_APB_VPLL_CFG_LOCK_DLY                                                   0x3f

                # Helper data. Values are to be looked up in a table from Data Sheet
                #(OFFSET, MASK, VALUE)      (0XFD1A003C, 0xFE7FEDEFU ,0x7E514C62U)  */
    mask_write 0XFD1A003C 0xFE7FEDEF 0x7E514C62
                # : UPDATE FB_DIV
                # Register : VPLL_CTRL @ 0XFD1A0038</p>

                # Mux select for determining which clock feeds this PLL. 0XX pss_ref_clk is the source 100 video clk is the source 101 pss_alt_
                # ef_clk is the source 110 aux_refclk[X] is the source 111 gt_crx_ref_clk is the source
                # PSU_CRF_APB_VPLL_CTRL_PRE_SRC                                                   0x0

                # The integer portion of the feedback divider to the PLL
                # PSU_CRF_APB_VPLL_CTRL_FBDIV                                                     0x39

                # This turns on the divide by 2 that is inside of the PLL. This does not change the VCO frequency, just the output frequency
                # PSU_CRF_APB_VPLL_CTRL_DIV2                                                      0x1

                # PLL Basic Control
                #(OFFSET, MASK, VALUE)      (0XFD1A0038, 0x00717F00U ,0x00013900U)  */
    mask_write 0XFD1A0038 0x00717F00 0x00013900
                # : BY PASS PLL
                # Register : VPLL_CTRL @ 0XFD1A0038</p>

                # Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4
                # cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRF_APB_VPLL_CTRL_BYPASS                                                    1

                # PLL Basic Control
                #(OFFSET, MASK, VALUE)      (0XFD1A0038, 0x00000008U ,0x00000008U)  */
    mask_write 0XFD1A0038 0x00000008 0x00000008
                # : ASSERT RESET
                # Register : VPLL_CTRL @ 0XFD1A0038</p>

                # Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS.
                # PSU_CRF_APB_VPLL_CTRL_RESET                                                     1

                # PLL Basic Control
                #(OFFSET, MASK, VALUE)      (0XFD1A0038, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD1A0038 0x00000001 0x00000001
                # : DEASSERT RESET
                # Register : VPLL_CTRL @ 0XFD1A0038</p>

                # Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS.
                # PSU_CRF_APB_VPLL_CTRL_RESET                                                     0

                # PLL Basic Control
                #(OFFSET, MASK, VALUE)      (0XFD1A0038, 0x00000001U ,0x00000000U)  */
    mask_write 0XFD1A0038 0x00000001 0x00000000
                # : CHECK PLL STATUS
                # Register : PLL_STATUS @ 0XFD1A0044</p>

                # VPLL is locked
                # PSU_CRF_APB_PLL_STATUS_VPLL_LOCK                                                1
    mask_poll 0XFD1A0044 0x00000004
                # : REMOVE PLL BY PASS
                # Register : VPLL_CTRL @ 0XFD1A0038</p>

                # Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4
                # cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRF_APB_VPLL_CTRL_BYPASS                                                    0

                # PLL Basic Control
                #(OFFSET, MASK, VALUE)      (0XFD1A0038, 0x00000008U ,0x00000000U)  */
    mask_write 0XFD1A0038 0x00000008 0x00000000
                # Register : VPLL_TO_LPD_CTRL @ 0XFD1A0050</p>

                # Divisor value for this clock.
                # PSU_CRF_APB_VPLL_TO_LPD_CTRL_DIVISOR0                                           0x3

                # Control for a clock that will be generated in the FPD, but used in the LPD as a clock source for the peripheral clock muxes.
                #(OFFSET, MASK, VALUE)      (0XFD1A0050, 0x00003F00U ,0x00000300U)  */
    mask_write 0XFD1A0050 0x00003F00 0x00000300
                # : VIDEO FRAC CFG
                # Register : VPLL_FRAC_CFG @ 0XFD1A0040</p>

                # Fractional SDM bypass control. When 0, PLL is in integer mode and it ignores all fractional data. When 1, PLL is in fractiona
                #  mode and uses DATA of this register for the fractional portion of the feedback divider.
                # PSU_CRF_APB_VPLL_FRAC_CFG_ENABLED                                               0x1

                # Fractional value for the Feedback value.
                # PSU_CRF_APB_VPLL_FRAC_CFG_DATA                                                  0x820c

                # Fractional control for the PLL
                #(OFFSET, MASK, VALUE)      (0XFD1A0040, 0x8000FFFFU ,0x8000820CU)  */
    mask_write 0XFD1A0040 0x8000FFFF 0x8000820C
}

set psu_clock_init_data {
                # : CLOCK CONTROL SLCR REGISTER
                # Register : GEM0_REF_CTRL @ 0XFF5E0050</p>

                # Clock active for the RX channel
                # PSU_CRL_APB_GEM0_REF_CTRL_RX_CLKACT                                             0x1

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_GEM0_REF_CTRL_CLKACT                                                0x1

                # 6 bit divider
                # PSU_CRL_APB_GEM0_REF_CTRL_DIVISOR1                                              0x1

                # 6 bit divider
                # PSU_CRL_APB_GEM0_REF_CTRL_DIVISOR0                                              0x8

                # 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_GEM0_REF_CTRL_SRCSEL                                                0x0

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E0050, 0x063F3F07U ,0x06010800U)  */
    mask_write 0XFF5E0050 0x063F3F07 0x06010800
                # Register : GEM1_REF_CTRL @ 0XFF5E0054</p>

                # Clock active for the RX channel
                # PSU_CRL_APB_GEM1_REF_CTRL_RX_CLKACT                                             0x1

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_GEM1_REF_CTRL_CLKACT                                                0x1

                # 6 bit divider
                # PSU_CRL_APB_GEM1_REF_CTRL_DIVISOR1                                              0x1

                # 6 bit divider
                # PSU_CRL_APB_GEM1_REF_CTRL_DIVISOR0                                              0x8

                # 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_GEM1_REF_CTRL_SRCSEL                                                0x0

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E0054, 0x063F3F07U ,0x06010800U)  */
    mask_write 0XFF5E0054 0x063F3F07 0x06010800
                # Register : GEM2_REF_CTRL @ 0XFF5E0058</p>

                # Clock active for the RX channel
                # PSU_CRL_APB_GEM2_REF_CTRL_RX_CLKACT                                             0x1

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_GEM2_REF_CTRL_CLKACT                                                0x1

                # 6 bit divider
                # PSU_CRL_APB_GEM2_REF_CTRL_DIVISOR1                                              0x1

                # 6 bit divider
                # PSU_CRL_APB_GEM2_REF_CTRL_DIVISOR0                                              0x8

                # 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_GEM2_REF_CTRL_SRCSEL                                                0x0

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E0058, 0x063F3F07U ,0x06010800U)  */
    mask_write 0XFF5E0058 0x063F3F07 0x06010800
                # Register : GEM3_REF_CTRL @ 0XFF5E005C</p>

                # Clock active for the RX channel
                # PSU_CRL_APB_GEM3_REF_CTRL_RX_CLKACT                                             0x1

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_GEM3_REF_CTRL_CLKACT                                                0x1

                # 6 bit divider
                # PSU_CRL_APB_GEM3_REF_CTRL_DIVISOR1                                              0x1

                # 6 bit divider
                # PSU_CRL_APB_GEM3_REF_CTRL_DIVISOR0                                              0xc

                # 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_GEM3_REF_CTRL_SRCSEL                                                0x0

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E005C, 0x063F3F07U ,0x06010C00U)  */
    mask_write 0XFF5E005C 0x063F3F07 0x06010C00
                # Register : GEM_TSU_REF_CTRL @ 0XFF5E0100</p>

                # 6 bit divider
                # PSU_CRL_APB_GEM_TSU_REF_CTRL_DIVISOR0                                           0x6

                # 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_GEM_TSU_REF_CTRL_SRCSEL                                             0x2

                # 6 bit divider
                # PSU_CRL_APB_GEM_TSU_REF_CTRL_DIVISOR1                                           0x1

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_GEM_TSU_REF_CTRL_CLKACT                                             0x1

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E0100, 0x013F3F07U ,0x01010602U)  */
    mask_write 0XFF5E0100 0x013F3F07 0x01010602
                # Register : USB0_BUS_REF_CTRL @ 0XFF5E0060</p>

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_USB0_BUS_REF_CTRL_CLKACT                                            0x1

                # 6 bit divider
                # PSU_CRL_APB_USB0_BUS_REF_CTRL_DIVISOR1                                          0x1

                # 6 bit divider
                # PSU_CRL_APB_USB0_BUS_REF_CTRL_DIVISOR0                                          0x6

                # 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_USB0_BUS_REF_CTRL_SRCSEL                                            0x0

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E0060, 0x023F3F07U ,0x02010600U)  */
    mask_write 0XFF5E0060 0x023F3F07 0x02010600
                # Register : USB1_BUS_REF_CTRL @ 0XFF5E0064</p>

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_USB1_BUS_REF_CTRL_CLKACT                                            0x1

                # 6 bit divider
                # PSU_CRL_APB_USB1_BUS_REF_CTRL_DIVISOR1                                          0x1

                # 6 bit divider
                # PSU_CRL_APB_USB1_BUS_REF_CTRL_DIVISOR0                                          0x4

                # 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_USB1_BUS_REF_CTRL_SRCSEL                                            0x0

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E0064, 0x023F3F07U ,0x02010400U)  */
    mask_write 0XFF5E0064 0x023F3F07 0x02010400
                # Register : USB3_DUAL_REF_CTRL @ 0XFF5E004C</p>

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_USB3_DUAL_REF_CTRL_CLKACT                                           0x1

                # 6 bit divider
                # PSU_CRL_APB_USB3_DUAL_REF_CTRL_DIVISOR1                                         0xf

                # 6 bit divider
                # PSU_CRL_APB_USB3_DUAL_REF_CTRL_DIVISOR0                                         0x5

                # 000 = IOPLL; 010 = RPLL; 011 = DPLL. (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_USB3_DUAL_REF_CTRL_SRCSEL                                           0x0

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E004C, 0x023F3F07U ,0x020F0500U)  */
    mask_write 0XFF5E004C 0x023F3F07 0x020F0500
                # Register : QSPI_REF_CTRL @ 0XFF5E0068</p>

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_QSPI_REF_CTRL_CLKACT                                                0x1

                # 6 bit divider
                # PSU_CRL_APB_QSPI_REF_CTRL_DIVISOR1                                              0x1

                # 6 bit divider
                # PSU_CRL_APB_QSPI_REF_CTRL_DIVISOR0                                              0xc

                # 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_QSPI_REF_CTRL_SRCSEL                                                0x0

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E0068, 0x013F3F07U ,0x01010C00U)  */
    mask_write 0XFF5E0068 0x013F3F07 0x01010C00
                # Register : SDIO0_REF_CTRL @ 0XFF5E006C</p>

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_SDIO0_REF_CTRL_CLKACT                                               0x1

                # 6 bit divider
                # PSU_CRL_APB_SDIO0_REF_CTRL_DIVISOR1                                             0x1

                # 6 bit divider
                # PSU_CRL_APB_SDIO0_REF_CTRL_DIVISOR0                                             0x7

                # 000 = IOPLL; 010 = RPLL; 011 = VPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_SDIO0_REF_CTRL_SRCSEL                                               0x2

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E006C, 0x013F3F07U ,0x01010702U)  */
    mask_write 0XFF5E006C 0x013F3F07 0x01010702
                # Register : SDIO1_REF_CTRL @ 0XFF5E0070</p>

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_SDIO1_REF_CTRL_CLKACT                                               0x1

                # 6 bit divider
                # PSU_CRL_APB_SDIO1_REF_CTRL_DIVISOR1                                             0x1

                # 6 bit divider
                # PSU_CRL_APB_SDIO1_REF_CTRL_DIVISOR0                                             0x6

                # 000 = IOPLL; 010 = RPLL; 011 = VPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_SDIO1_REF_CTRL_SRCSEL                                               0x2

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E0070, 0x013F3F07U ,0x01010602U)  */
    mask_write 0XFF5E0070 0x013F3F07 0x01010602
                # Register : SDIO_CLK_CTRL @ 0XFF18030C</p>

                # MIO pad selection for sdio1_rx_clk (feedback clock from the PAD) 0: MIO [51] 1: MIO [76]
                # PSU_IOU_SLCR_SDIO_CLK_CTRL_SDIO1_RX_SRC_SEL                                     0

                # SoC Debug Clock Control
                #(OFFSET, MASK, VALUE)      (0XFF18030C, 0x00020000U ,0x00000000U)  */
    mask_write 0XFF18030C 0x00020000 0x00000000
                # Register : UART0_REF_CTRL @ 0XFF5E0074</p>

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_UART0_REF_CTRL_CLKACT                                               0x1

                # 6 bit divider
                # PSU_CRL_APB_UART0_REF_CTRL_DIVISOR1                                             0x1

                # 6 bit divider
                # PSU_CRL_APB_UART0_REF_CTRL_DIVISOR0                                             0xf

                # 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_UART0_REF_CTRL_SRCSEL                                               0x0

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E0074, 0x013F3F07U ,0x01010F00U)  */
    mask_write 0XFF5E0074 0x013F3F07 0x01010F00
                # Register : UART1_REF_CTRL @ 0XFF5E0078</p>

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_UART1_REF_CTRL_CLKACT                                               0x1

                # 6 bit divider
                # PSU_CRL_APB_UART1_REF_CTRL_DIVISOR1                                             0x1

                # 6 bit divider
                # PSU_CRL_APB_UART1_REF_CTRL_DIVISOR0                                             0xf

                # 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_UART1_REF_CTRL_SRCSEL                                               0x0

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E0078, 0x013F3F07U ,0x01010F00U)  */
    mask_write 0XFF5E0078 0x013F3F07 0x01010F00
                # Register : I2C0_REF_CTRL @ 0XFF5E0120</p>

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_I2C0_REF_CTRL_CLKACT                                                0x1

                # 6 bit divider
                # PSU_CRL_APB_I2C0_REF_CTRL_DIVISOR1                                              0x1

                # 6 bit divider
                # PSU_CRL_APB_I2C0_REF_CTRL_DIVISOR0                                              0xf

                # 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_I2C0_REF_CTRL_SRCSEL                                                0x0

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E0120, 0x013F3F07U ,0x01010F00U)  */
    mask_write 0XFF5E0120 0x013F3F07 0x01010F00
                # Register : I2C1_REF_CTRL @ 0XFF5E0124</p>

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_I2C1_REF_CTRL_CLKACT                                                0x1

                # 6 bit divider
                # PSU_CRL_APB_I2C1_REF_CTRL_DIVISOR1                                              0x1

                # 6 bit divider
                # PSU_CRL_APB_I2C1_REF_CTRL_DIVISOR0                                              0xf

                # 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_I2C1_REF_CTRL_SRCSEL                                                0x0

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E0124, 0x013F3F07U ,0x01010F00U)  */
    mask_write 0XFF5E0124 0x013F3F07 0x01010F00
                # Register : SPI0_REF_CTRL @ 0XFF5E007C</p>

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_SPI0_REF_CTRL_CLKACT                                                0x1

                # 6 bit divider
                # PSU_CRL_APB_SPI0_REF_CTRL_DIVISOR1                                              0x1

                # 6 bit divider
                # PSU_CRL_APB_SPI0_REF_CTRL_DIVISOR0                                              0x7

                # 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_SPI0_REF_CTRL_SRCSEL                                                0x2

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E007C, 0x013F3F07U ,0x01010702U)  */
    mask_write 0XFF5E007C 0x013F3F07 0x01010702
                # Register : SPI1_REF_CTRL @ 0XFF5E0080</p>

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_SPI1_REF_CTRL_CLKACT                                                0x1

                # 6 bit divider
                # PSU_CRL_APB_SPI1_REF_CTRL_DIVISOR1                                              0x1

                # 6 bit divider
                # PSU_CRL_APB_SPI1_REF_CTRL_DIVISOR0                                              0x7

                # 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_SPI1_REF_CTRL_SRCSEL                                                0x2

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E0080, 0x013F3F07U ,0x01010702U)  */
    mask_write 0XFF5E0080 0x013F3F07 0x01010702
                # Register : CAN0_REF_CTRL @ 0XFF5E0084</p>

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_CAN0_REF_CTRL_CLKACT                                                0x1

                # 6 bit divider
                # PSU_CRL_APB_CAN0_REF_CTRL_DIVISOR1                                              0x1

                # 6 bit divider
                # PSU_CRL_APB_CAN0_REF_CTRL_DIVISOR0                                              0xa

                # 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_CAN0_REF_CTRL_SRCSEL                                                0x0

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E0084, 0x013F3F07U ,0x01010A00U)  */
    mask_write 0XFF5E0084 0x013F3F07 0x01010A00
                # Register : CAN1_REF_CTRL @ 0XFF5E0088</p>

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_CAN1_REF_CTRL_CLKACT                                                0x1

                # 6 bit divider
                # PSU_CRL_APB_CAN1_REF_CTRL_DIVISOR1                                              0x1

                # 6 bit divider
                # PSU_CRL_APB_CAN1_REF_CTRL_DIVISOR0                                              0xf

                # 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_CAN1_REF_CTRL_SRCSEL                                                0x0

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E0088, 0x013F3F07U ,0x01010F00U)  */
    mask_write 0XFF5E0088 0x013F3F07 0x01010F00
                # Register : CPU_R5_CTRL @ 0XFF5E0090</p>

                # Turing this off will shut down the OCM, some parts of the APM, and prevent transactions going from the FPD to the LPD and cou
                # d lead to system hang
                # PSU_CRL_APB_CPU_R5_CTRL_CLKACT                                                  0x1

                # 6 bit divider
                # PSU_CRL_APB_CPU_R5_CTRL_DIVISOR0                                                0x3

                # 000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_CPU_R5_CTRL_SRCSEL                                                  0x2

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E0090, 0x01003F07U ,0x01000302U)  */
    mask_write 0XFF5E0090 0x01003F07 0x01000302
                # Register : IOU_SWITCH_CTRL @ 0XFF5E009C</p>

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_IOU_SWITCH_CTRL_CLKACT                                              0x1

                # 6 bit divider
                # PSU_CRL_APB_IOU_SWITCH_CTRL_DIVISOR0                                            0x6

                # 000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_IOU_SWITCH_CTRL_SRCSEL                                              0x2

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E009C, 0x01003F07U ,0x01000602U)  */
    mask_write 0XFF5E009C 0x01003F07 0x01000602
                # Register : CSU_PLL_CTRL @ 0XFF5E00A0</p>

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_CSU_PLL_CTRL_CLKACT                                                 0x1

                # 6 bit divider
                # PSU_CRL_APB_CSU_PLL_CTRL_DIVISOR0                                               0x3

                # 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_CSU_PLL_CTRL_SRCSEL                                                 0x2

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E00A0, 0x01003F07U ,0x01000302U)  */
    mask_write 0XFF5E00A0 0x01003F07 0x01000302
                # Register : PCAP_CTRL @ 0XFF5E00A4</p>

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_PCAP_CTRL_CLKACT                                                    0x1

                # 6 bit divider
                # PSU_CRL_APB_PCAP_CTRL_DIVISOR0                                                  0x6

                # 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_PCAP_CTRL_SRCSEL                                                    0x2

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E00A4, 0x01003F07U ,0x01000602U)  */
    mask_write 0XFF5E00A4 0x01003F07 0x01000602
                # Register : LPD_SWITCH_CTRL @ 0XFF5E00A8</p>

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_LPD_SWITCH_CTRL_CLKACT                                              0x1

                # 6 bit divider
                # PSU_CRL_APB_LPD_SWITCH_CTRL_DIVISOR0                                            0x3

                # 000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_LPD_SWITCH_CTRL_SRCSEL                                              0x2

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E00A8, 0x01003F07U ,0x01000302U)  */
    mask_write 0XFF5E00A8 0x01003F07 0x01000302
                # Register : LPD_LSBUS_CTRL @ 0XFF5E00AC</p>

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_LPD_LSBUS_CTRL_CLKACT                                               0x1

                # 6 bit divider
                # PSU_CRL_APB_LPD_LSBUS_CTRL_DIVISOR0                                             0xf

                # 000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_LPD_LSBUS_CTRL_SRCSEL                                               0x2

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E00AC, 0x01003F07U ,0x01000F02U)  */
    mask_write 0XFF5E00AC 0x01003F07 0x01000F02
                # Register : DBG_LPD_CTRL @ 0XFF5E00B0</p>

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_DBG_LPD_CTRL_CLKACT                                                 0x1

                # 6 bit divider
                # PSU_CRL_APB_DBG_LPD_CTRL_DIVISOR0                                               0x6

                # 000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_DBG_LPD_CTRL_SRCSEL                                                 0x2

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E00B0, 0x01003F07U ,0x01000602U)  */
    mask_write 0XFF5E00B0 0x01003F07 0x01000602
                # Register : NAND_REF_CTRL @ 0XFF5E00B4</p>

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_NAND_REF_CTRL_CLKACT                                                0x1

                # 6 bit divider
                # PSU_CRL_APB_NAND_REF_CTRL_DIVISOR1                                              0x1

                # 6 bit divider
                # PSU_CRL_APB_NAND_REF_CTRL_DIVISOR0                                              0xa

                # 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_NAND_REF_CTRL_SRCSEL                                                0x0

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E00B4, 0x013F3F07U ,0x01010A00U)  */
    mask_write 0XFF5E00B4 0x013F3F07 0x01010A00
                # Register : ADMA_REF_CTRL @ 0XFF5E00B8</p>

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_ADMA_REF_CTRL_CLKACT                                                0x1

                # 6 bit divider
                # PSU_CRL_APB_ADMA_REF_CTRL_DIVISOR0                                              0x3

                # 000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_ADMA_REF_CTRL_SRCSEL                                                0x2

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E00B8, 0x01003F07U ,0x01000302U)  */
    mask_write 0XFF5E00B8 0x01003F07 0x01000302
                # Register : PL0_REF_CTRL @ 0XFF5E00C0</p>

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_PL0_REF_CTRL_CLKACT                                                 0x1

                # 6 bit divider
                # PSU_CRL_APB_PL0_REF_CTRL_DIVISOR1                                               0x1

                # 6 bit divider
                # PSU_CRL_APB_PL0_REF_CTRL_DIVISOR0                                               0xf

                # 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_PL0_REF_CTRL_SRCSEL                                                 0x0

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E00C0, 0x013F3F07U ,0x01010F00U)  */
    mask_write 0XFF5E00C0 0x013F3F07 0x01010F00
                # Register : PL1_REF_CTRL @ 0XFF5E00C4</p>

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_PL1_REF_CTRL_CLKACT                                                 0x1

                # 6 bit divider
                # PSU_CRL_APB_PL1_REF_CTRL_DIVISOR1                                               0x4

                # 6 bit divider
                # PSU_CRL_APB_PL1_REF_CTRL_DIVISOR0                                               0xf

                # 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_PL1_REF_CTRL_SRCSEL                                                 0x0

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E00C4, 0x013F3F07U ,0x01040F00U)  */
    mask_write 0XFF5E00C4 0x013F3F07 0x01040F00
                # Register : PL2_REF_CTRL @ 0XFF5E00C8</p>

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_PL2_REF_CTRL_CLKACT                                                 0x1

                # 6 bit divider
                # PSU_CRL_APB_PL2_REF_CTRL_DIVISOR1                                               0x1

                # 6 bit divider
                # PSU_CRL_APB_PL2_REF_CTRL_DIVISOR0                                               0x4

                # 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_PL2_REF_CTRL_SRCSEL                                                 0x2

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E00C8, 0x013F3F07U ,0x01010402U)  */
    mask_write 0XFF5E00C8 0x013F3F07 0x01010402
                # Register : PL3_REF_CTRL @ 0XFF5E00CC</p>

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_PL3_REF_CTRL_CLKACT                                                 0x1

                # 6 bit divider
                # PSU_CRL_APB_PL3_REF_CTRL_DIVISOR1                                               0x1

                # 6 bit divider
                # PSU_CRL_APB_PL3_REF_CTRL_DIVISOR0                                               0x3

                # 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_PL3_REF_CTRL_SRCSEL                                                 0x2

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E00CC, 0x013F3F07U ,0x01010302U)  */
    mask_write 0XFF5E00CC 0x013F3F07 0x01010302
                # Register : AMS_REF_CTRL @ 0XFF5E0108</p>

                # 6 bit divider
                # PSU_CRL_APB_AMS_REF_CTRL_DIVISOR1                                               0x1

                # 6 bit divider
                # PSU_CRL_APB_AMS_REF_CTRL_DIVISOR0                                               0x1d

                # 000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new
                # clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_AMS_REF_CTRL_SRCSEL                                                 0x2

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_AMS_REF_CTRL_CLKACT                                                 0x1

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E0108, 0x013F3F07U ,0x01011D02U)  */
    mask_write 0XFF5E0108 0x013F3F07 0x01011D02
                # Register : DLL_REF_CTRL @ 0XFF5E0104</p>

                # 000 = IOPLL; 001 = RPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new clock. This
                # is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_DLL_REF_CTRL_SRCSEL                                                 0

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E0104, 0x00000007U ,0x00000000U)  */
    mask_write 0XFF5E0104 0x00000007 0x00000000
                # Register : TIMESTAMP_REF_CTRL @ 0XFF5E0128</p>

                # 6 bit divider
                # PSU_CRL_APB_TIMESTAMP_REF_CTRL_DIVISOR0                                         0xf

                # 1XX = pss_ref_clk; 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 
                #  cycles of the new clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRL_APB_TIMESTAMP_REF_CTRL_SRCSEL                                           0x0

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRL_APB_TIMESTAMP_REF_CTRL_CLKACT                                           0x1

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFF5E0128, 0x01003F07U ,0x01000F00U)  */
    mask_write 0XFF5E0128 0x01003F07 0x01000F00
                # Register : SATA_REF_CTRL @ 0XFD1A00A0</p>

                # 000 = IOPLL_TO_FPD; 010 = APLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of 
                # he new clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRF_APB_SATA_REF_CTRL_SRCSEL                                                0x0

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRF_APB_SATA_REF_CTRL_CLKACT                                                0x1

                # 6 bit divider
                # PSU_CRF_APB_SATA_REF_CTRL_DIVISOR0                                              0x2

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFD1A00A0, 0x01003F07U ,0x01000200U)  */
    mask_write 0XFD1A00A0 0x01003F07 0x01000200
                # Register : PCIE_REF_CTRL @ 0XFD1A00B4</p>

                # 000 = IOPLL_TO_FPD; 010 = RPLL_TO_FPD; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cyc
                # es of the new clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRF_APB_PCIE_REF_CTRL_SRCSEL                                                0x0

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRF_APB_PCIE_REF_CTRL_CLKACT                                                0x1

                # 6 bit divider
                # PSU_CRF_APB_PCIE_REF_CTRL_DIVISOR0                                              0x2

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFD1A00B4, 0x01003F07U ,0x01000200U)  */
    mask_write 0XFD1A00B4 0x01003F07 0x01000200
                # Register : DP_VIDEO_REF_CTRL @ 0XFD1A0070</p>

                # 6 bit divider
                # PSU_CRF_APB_DP_VIDEO_REF_CTRL_DIVISOR1                                          0x1

                # 6 bit divider
                # PSU_CRF_APB_DP_VIDEO_REF_CTRL_DIVISOR0                                          0x3

                # 000 = VPLL; 010 = DPLL; 011 = RPLL_TO_FPD - might be using extra mux; (This signal may only be toggled after 4 cycles of the 
                # ld clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRF_APB_DP_VIDEO_REF_CTRL_SRCSEL                                            0x3

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRF_APB_DP_VIDEO_REF_CTRL_CLKACT                                            0x1

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFD1A0070, 0x013F3F07U ,0x01010303U)  */
    mask_write 0XFD1A0070 0x013F3F07 0x01010303
                # Register : DP_AUDIO_REF_CTRL @ 0XFD1A0074</p>

                # 6 bit divider
                # PSU_CRF_APB_DP_AUDIO_REF_CTRL_DIVISOR1                                          0x1

                # 6 bit divider
                # PSU_CRF_APB_DP_AUDIO_REF_CTRL_DIVISOR0                                          0x27

                # 000 = VPLL; 010 = DPLL; 011 = RPLL_TO_FPD - might be using extra mux; (This signal may only be toggled after 4 cycles of the 
                # ld clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRF_APB_DP_AUDIO_REF_CTRL_SRCSEL                                            0x0

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRF_APB_DP_AUDIO_REF_CTRL_CLKACT                                            0x1

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFD1A0074, 0x013F3F07U ,0x01012700U)  */
    mask_write 0XFD1A0074 0x013F3F07 0x01012700
                # Register : DP_STC_REF_CTRL @ 0XFD1A007C</p>

                # 6 bit divider
                # PSU_CRF_APB_DP_STC_REF_CTRL_DIVISOR1                                            0x1

                # 6 bit divider
                # PSU_CRF_APB_DP_STC_REF_CTRL_DIVISOR0                                            0x11

                # 000 = VPLL; 010 = DPLL; 011 = RPLL_TO_FPD; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of t
                # e new clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRF_APB_DP_STC_REF_CTRL_SRCSEL                                              0x3

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRF_APB_DP_STC_REF_CTRL_CLKACT                                              0x1

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFD1A007C, 0x013F3F07U ,0x01011103U)  */
    mask_write 0XFD1A007C 0x013F3F07 0x01011103
                # Register : ACPU_CTRL @ 0XFD1A0060</p>

                # 6 bit divider
                # PSU_CRF_APB_ACPU_CTRL_DIVISOR0                                                  0x1

                # 000 = APLL; 010 = DPLL; 011 = VPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new 
                # lock. This is not usually an issue, but designers must be aware.)
                # PSU_CRF_APB_ACPU_CTRL_SRCSEL                                                    0x0

                # Clock active signal. Switch to 0 to disable the clock. For the half speed APU Clock
                # PSU_CRF_APB_ACPU_CTRL_CLKACT_HALF                                               0x1

                # Clock active signal. Switch to 0 to disable the clock. For the full speed ACPUX Clock. This will shut off the high speed cloc
                #  to the entire APU
                # PSU_CRF_APB_ACPU_CTRL_CLKACT_FULL                                               0x1

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFD1A0060, 0x03003F07U ,0x03000100U)  */
    mask_write 0XFD1A0060 0x03003F07 0x03000100
                # Register : DBG_TRACE_CTRL @ 0XFD1A0064</p>

                # 6 bit divider
                # PSU_CRF_APB_DBG_TRACE_CTRL_DIVISOR0                                             0x2

                # 000 = IOPLL_TO_FPD; 010 = DPLL; 011 = APLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of 
                # he new clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRF_APB_DBG_TRACE_CTRL_SRCSEL                                               0x0

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRF_APB_DBG_TRACE_CTRL_CLKACT                                               0x1

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFD1A0064, 0x01003F07U ,0x01000200U)  */
    mask_write 0XFD1A0064 0x01003F07 0x01000200
                # Register : DBG_FPD_CTRL @ 0XFD1A0068</p>

                # 6 bit divider
                # PSU_CRF_APB_DBG_FPD_CTRL_DIVISOR0                                               0x2

                # 000 = IOPLL_TO_FPD; 010 = DPLL; 011 = APLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of 
                # he new clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRF_APB_DBG_FPD_CTRL_SRCSEL                                                 0x0

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRF_APB_DBG_FPD_CTRL_CLKACT                                                 0x1

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFD1A0068, 0x01003F07U ,0x01000200U)  */
    mask_write 0XFD1A0068 0x01003F07 0x01000200
                # Register : DDR_CTRL @ 0XFD1A0080</p>

                # 6 bit divider
                # PSU_CRF_APB_DDR_CTRL_DIVISOR0                                                   0x2

                # 000 = DPLL; 001 = VPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new clock. This 
                # s not usually an issue, but designers must be aware.)
                # PSU_CRF_APB_DDR_CTRL_SRCSEL                                                     0x0

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFD1A0080, 0x00003F07U ,0x00000200U)  */
    mask_write 0XFD1A0080 0x00003F07 0x00000200
                # Register : GPU_REF_CTRL @ 0XFD1A0084</p>

                # 6 bit divider
                # PSU_CRF_APB_GPU_REF_CTRL_DIVISOR0                                               0x1

                # 000 = IOPLL_TO_FPD; 010 = VPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of 
                # he new clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRF_APB_GPU_REF_CTRL_SRCSEL                                                 0x0

                # Clock active signal. Switch to 0 to disable the clock, which will stop clock for GPU (and both Pixel Processors).
                # PSU_CRF_APB_GPU_REF_CTRL_CLKACT                                                 0x1

                # Clock active signal for Pixel Processor. Switch to 0 to disable the clock only to this Pixel Processor
                # PSU_CRF_APB_GPU_REF_CTRL_PP0_CLKACT                                             0x1

                # Clock active signal for Pixel Processor. Switch to 0 to disable the clock only to this Pixel Processor
                # PSU_CRF_APB_GPU_REF_CTRL_PP1_CLKACT                                             0x1

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFD1A0084, 0x07003F07U ,0x07000100U)  */
    mask_write 0XFD1A0084 0x07003F07 0x07000100
                # Register : GDMA_REF_CTRL @ 0XFD1A00B8</p>

                # 6 bit divider
                # PSU_CRF_APB_GDMA_REF_CTRL_DIVISOR0                                              0x2

                # 000 = APLL; 010 = VPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new 
                # lock. This is not usually an issue, but designers must be aware.)
                # PSU_CRF_APB_GDMA_REF_CTRL_SRCSEL                                                0x0

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRF_APB_GDMA_REF_CTRL_CLKACT                                                0x1

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFD1A00B8, 0x01003F07U ,0x01000200U)  */
    mask_write 0XFD1A00B8 0x01003F07 0x01000200
                # Register : DPDMA_REF_CTRL @ 0XFD1A00BC</p>

                # 6 bit divider
                # PSU_CRF_APB_DPDMA_REF_CTRL_DIVISOR0                                             0x2

                # 000 = APLL; 010 = VPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new 
                # lock. This is not usually an issue, but designers must be aware.)
                # PSU_CRF_APB_DPDMA_REF_CTRL_SRCSEL                                               0x0

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRF_APB_DPDMA_REF_CTRL_CLKACT                                               0x1

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFD1A00BC, 0x01003F07U ,0x01000200U)  */
    mask_write 0XFD1A00BC 0x01003F07 0x01000200
                # Register : TOPSW_MAIN_CTRL @ 0XFD1A00C0</p>

                # 6 bit divider
                # PSU_CRF_APB_TOPSW_MAIN_CTRL_DIVISOR0                                            0x2

                # 000 = APLL; 010 = VPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new 
                # lock. This is not usually an issue, but designers must be aware.)
                # PSU_CRF_APB_TOPSW_MAIN_CTRL_SRCSEL                                              0x2

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRF_APB_TOPSW_MAIN_CTRL_CLKACT                                              0x1

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFD1A00C0, 0x01003F07U ,0x01000202U)  */
    mask_write 0XFD1A00C0 0x01003F07 0x01000202
                # Register : TOPSW_LSBUS_CTRL @ 0XFD1A00C4</p>

                # 6 bit divider
                # PSU_CRF_APB_TOPSW_LSBUS_CTRL_DIVISOR0                                           0x5

                # 000 = APLL; 010 = IOPLL_TO_FPD; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of 
                # he new clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRF_APB_TOPSW_LSBUS_CTRL_SRCSEL                                             0x2

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRF_APB_TOPSW_LSBUS_CTRL_CLKACT                                             0x1

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFD1A00C4, 0x01003F07U ,0x01000502U)  */
    mask_write 0XFD1A00C4 0x01003F07 0x01000502
                # Register : GTGREF0_REF_CTRL @ 0XFD1A00C8</p>

                # 6 bit divider
                # PSU_CRF_APB_GTGREF0_REF_CTRL_DIVISOR0                                           0x4

                # 000 = IOPLL_TO_FPD; 010 = APLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of 
                # he new clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRF_APB_GTGREF0_REF_CTRL_SRCSEL                                             0x0

                # Clock active signal. Switch to 0 to disable the clock
                # PSU_CRF_APB_GTGREF0_REF_CTRL_CLKACT                                             0x1

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFD1A00C8, 0x01003F07U ,0x01000400U)  */
    mask_write 0XFD1A00C8 0x01003F07 0x01000400
                # Register : DBG_TSTMP_CTRL @ 0XFD1A00F8</p>

                # 6 bit divider
                # PSU_CRF_APB_DBG_TSTMP_CTRL_DIVISOR0                                             0x2

                # 000 = IOPLL_TO_FPD; 010 = DPLL; 011 = APLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of 
                # he new clock. This is not usually an issue, but designers must be aware.)
                # PSU_CRF_APB_DBG_TSTMP_CTRL_SRCSEL                                               0x0

                # This register controls this reference clock
                #(OFFSET, MASK, VALUE)      (0XFD1A00F8, 0x00003F07U ,0x00000200U)  */
    mask_write 0XFD1A00F8 0x00003F07 0x00000200
                # Register : IOU_TTC_APB_CLK @ 0XFF180380</p>

                # 00" = Select the APB switch clock for the APB interface of TTC0'01" = Select the PLL ref clock for the APB interface of TTC0'
                # 0" = Select the R5 clock for the APB interface of TTC0
                # PSU_IOU_SLCR_IOU_TTC_APB_CLK_TTC0_SEL                                           0

                # 00" = Select the APB switch clock for the APB interface of TTC1'01" = Select the PLL ref clock for the APB interface of TTC1'
                # 0" = Select the R5 clock for the APB interface of TTC1
                # PSU_IOU_SLCR_IOU_TTC_APB_CLK_TTC1_SEL                                           0

                # 00" = Select the APB switch clock for the APB interface of TTC2'01" = Select the PLL ref clock for the APB interface of TTC2'
                # 0" = Select the R5 clock for the APB interface of TTC2
                # PSU_IOU_SLCR_IOU_TTC_APB_CLK_TTC2_SEL                                           0

                # 00" = Select the APB switch clock for the APB interface of TTC3'01" = Select the PLL ref clock for the APB interface of TTC3'
                # 0" = Select the R5 clock for the APB interface of TTC3
                # PSU_IOU_SLCR_IOU_TTC_APB_CLK_TTC3_SEL                                           0

                # TTC APB clock select
                #(OFFSET, MASK, VALUE)      (0XFF180380, 0x000000FFU ,0x00000000U)  */
    mask_write 0XFF180380 0x000000FF 0x00000000
                # Register : WDT_CLK_SEL @ 0XFD610100</p>

                # System watchdog timer clock source selection: 0: Internal APB clock 1: External (PL clock via EMIO or Pinout clock via MIO)
                # PSU_FPD_SLCR_WDT_CLK_SEL_SELECT                                                 0

                # SWDT clock source select
                #(OFFSET, MASK, VALUE)      (0XFD610100, 0x00000001U ,0x00000000U)  */
    mask_write 0XFD610100 0x00000001 0x00000000
                # Register : WDT_CLK_SEL @ 0XFF180300</p>

                # System watchdog timer clock source selection: 0: internal clock APB clock 1: external clock from PL via EMIO, or from pinout 
                # ia MIO
                # PSU_IOU_SLCR_WDT_CLK_SEL_SELECT                                                 0

                # SWDT clock source select
                #(OFFSET, MASK, VALUE)      (0XFF180300, 0x00000001U ,0x00000000U)  */
    mask_write 0XFF180300 0x00000001 0x00000000
                # Register : CSUPMU_WDT_CLK_SEL @ 0XFF410050</p>

                # System watchdog timer clock source selection: 0: internal clock APB clock 1: external clock pss_ref_clk
                # PSU_LPD_SLCR_CSUPMU_WDT_CLK_SEL_SELECT                                          0

                # SWDT clock source select
                #(OFFSET, MASK, VALUE)      (0XFF410050, 0x00000001U ,0x00000000U)  */
    mask_write 0XFF410050 0x00000001 0x00000000
}

set psu_ddr_init_data {
                # : DDR INITIALIZATION
                # : DDR CONTROLLER RESET
                # Register : RST_DDR_SS @ 0XFD1A0108</p>

                # DDR block level reset inside of the DDR Sub System
                # PSU_CRF_APB_RST_DDR_SS_DDR_RESET                                                0X1

                # DDR sub system block level reset
                #(OFFSET, MASK, VALUE)      (0XFD1A0108, 0x00000008U ,0x00000008U)  */
    mask_write 0XFD1A0108 0x00000008 0x00000008
                # Register : MSTR @ 0XFD070000</p>

                # Indicates the configuration of the device used in the system. - 00 - x4 device - 01 - x8 device - 10 - x16 device - 11 - x32 
                # evice
                # PSU_DDRC_MSTR_DEVICE_CONFIG                                                     0x1

                # Choose which registers are used. - 0 - Original registers - 1 - Shadow registers
                # PSU_DDRC_MSTR_FREQUENCY_MODE                                                    0x0

                # Only present for multi-rank configurations. Each bit represents one rank. For two-rank configurations, only bits[25:24] are p
                # esent. - 1 - populated - 0 - unpopulated LSB is the lowest rank number. For 2 ranks following combinations are legal: - 01 - 
                # ne rank - 11 - Two ranks - Others - Reserved. For 4 ranks following combinations are legal: - 0001 - One rank - 0011 - Two ra
                # ks - 1111 - Four ranks
                # PSU_DDRC_MSTR_ACTIVE_RANKS                                                      0x1

                # SDRAM burst length used: - 0001 - Burst length of 2 (only supported for mDDR) - 0010 - Burst length of 4 - 0100 - Burst lengt
                #  of 8 - 1000 - Burst length of 16 (only supported for mDDR, LPDDR2, and LPDDR4) All other values are reserved. This controls 
                # he burst size used to access the SDRAM. This must match the burst length mode register setting in the SDRAM. (For BC4/8 on-th
                # -fly mode of DDR3 and DDR4, set this field to 0x0100) Burst length of 2 is not supported with AXI ports when MEMC_BURST_LENGT
                #  is 8. Burst length of 2 is only supported with MEMC_FREQ_RATIO = 1
                # PSU_DDRC_MSTR_BURST_RDWR                                                        0x4

                # Set to 1 when the uMCTL2 and DRAM has to be put in DLL-off mode for low frequency operation. Set to 0 to put uMCTL2 and DRAM 
                # n DLL-on mode for normal frequency operation. If DDR4 CRC/parity retry is enabled (CRCPARCTL1.crc_parity_retry_enable = 1), d
                # l_off_mode is not supported, and this bit must be set to '0'.
                # PSU_DDRC_MSTR_DLL_OFF_MODE                                                      0x0

                # Selects proportion of DQ bus width that is used by the SDRAM - 00 - Full DQ bus width to SDRAM - 01 - Half DQ bus width to SD
                # AM - 10 - Quarter DQ bus width to SDRAM - 11 - Reserved. Note that half bus width mode is only supported when the SDRAM bus w
                # dth is a multiple of 16, and quarter bus width mode is only supported when the SDRAM bus width is a multiple of 32 and the co
                # figuration parameter MEMC_QBUS_SUPPORT is set. Bus width refers to DQ bus width (excluding any ECC width).
                # PSU_DDRC_MSTR_DATA_BUS_WIDTH                                                    0x0

                # 1 indicates put the DRAM in geardown mode (2N) and 0 indicates put the DRAM in normal mode (1N). This register can be changed
                #  only when the Controller is in self-refresh mode. This signal must be set the same value as MR3 bit A3. Note: Geardown mode 
                # s not supported if the configuration parameter MEMC_CMD_RTN2IDLE is set
                # PSU_DDRC_MSTR_GEARDOWN_MODE                                                     0x0

                # If 1, then uMCTL2 uses 2T timing. Otherwise, uses 1T timing. In 2T timing, all command signals (except chip select) are held 
                # or 2 clocks on the SDRAM bus. Chip select is asserted on the second cycle of the command Note: 2T timing is not supported in 
                # PDDR2/LPDDR3/LPDDR4 mode Note: 2T timing is not supported if the configuration parameter MEMC_CMD_RTN2IDLE is set Note: 2T ti
                # ing is not supported in DDR4 geardown mode.
                # PSU_DDRC_MSTR_EN_2T_TIMING_MODE                                                 0x0

                # When set, enable burst-chop in DDR3/DDR4. Burst Chop for Reads is exercised only in HIF configurations (UMCTL2_INCL_ARB not s
                # t) and if in full bus width mode (MSTR.data_bus_width = 00). Burst Chop for Writes is exercised only if Partial Writes enable
                #  (UMCTL2_PARTIAL_WR=1) and if CRC is disabled (CRCPARCTL1.crc_enable = 0). If DDR4 CRC/parity retry is enabled (CRCPARCTL1.cr
                # _parity_retry_enable = 1), burst chop is not supported, and this bit must be set to '0'
                # PSU_DDRC_MSTR_BURSTCHOP                                                         0x0

                # Select LPDDR4 SDRAM - 1 - LPDDR4 SDRAM device in use. - 0 - non-LPDDR4 device in use Present only in designs configured to su
                # port LPDDR4.
                # PSU_DDRC_MSTR_LPDDR4                                                            0x0

                # Select DDR4 SDRAM - 1 - DDR4 SDRAM device in use. - 0 - non-DDR4 device in use Present only in designs configured to support 
                # DR4.
                # PSU_DDRC_MSTR_DDR4                                                              0x1

                # Select LPDDR3 SDRAM - 1 - LPDDR3 SDRAM device in use. - 0 - non-LPDDR3 device in use Present only in designs configured to su
                # port LPDDR3.
                # PSU_DDRC_MSTR_LPDDR3                                                            0x0

                # Select LPDDR2 SDRAM - 1 - LPDDR2 SDRAM device in use. - 0 - non-LPDDR2 device in use Present only in designs configured to su
                # port LPDDR2.
                # PSU_DDRC_MSTR_LPDDR2                                                            0x0

                # Select DDR3 SDRAM - 1 - DDR3 SDRAM device in use - 0 - non-DDR3 SDRAM device in use Only present in designs that support DDR3
                # 
                # PSU_DDRC_MSTR_DDR3                                                              0x0

                # Master Register
                #(OFFSET, MASK, VALUE)      (0XFD070000, 0xE30FBE3DU ,0x41040010U)  */
    mask_write 0XFD070000 0xE30FBE3D 0x41040010
                # Register : MRCTRL0 @ 0XFD070010</p>

                # Setting this register bit to 1 triggers a mode register read or write operation. When the MR operation is complete, the uMCTL
                #  automatically clears this bit. The other register fields of this register must be written in a separate APB transaction, bef
                # re setting this mr_wr bit. It is recommended NOT to set this signal if in Init, Deep power-down or MPSM operating modes.
                # PSU_DDRC_MRCTRL0_MR_WR                                                          0x0

                # Address of the mode register that is to be written to. - 0000 - MR0 - 0001 - MR1 - 0010 - MR2 - 0011 - MR3 - 0100 - MR4 - 010
                #  - MR5 - 0110 - MR6 - 0111 - MR7 Don't Care for LPDDR2/LPDDR3/LPDDR4 (see MRCTRL1.mr_data for mode register addressing in LPD
                # R2/LPDDR3/LPDDR4) This signal is also used for writing to control words of RDIMMs. In that case, it corresponds to the bank a
                # dress bits sent to the RDIMM In case of DDR4, the bit[3:2] corresponds to the bank group bits. Therefore, the bit[3] as well 
                # s the bit[2:0] must be set to an appropriate value which is considered both the Address Mirroring of UDIMMs/RDIMMs and the Ou
                # put Inversion of RDIMMs.
                # PSU_DDRC_MRCTRL0_MR_ADDR                                                        0x0

                # Controls which rank is accessed by MRCTRL0.mr_wr. Normally, it is desired to access all ranks, so all bits should be set to 1
                #  However, for multi-rank UDIMMs/RDIMMs which implement address mirroring, it may be necessary to access ranks individually. E
                # amples (assume uMCTL2 is configured for 4 ranks): - 0x1 - select rank 0 only - 0x2 - select rank 1 only - 0x5 - select ranks 
                #  and 2 - 0xA - select ranks 1 and 3 - 0xF - select ranks 0, 1, 2 and 3
                # PSU_DDRC_MRCTRL0_MR_RANK                                                        0x3

                # Indicates whether Software intervention is allowed via MRCTRL0/MRCTRL1 before automatic SDRAM initialization routine or not. 
                # or DDR4, this bit can be used to initialize the DDR4 RCD (MR7) before automatic SDRAM initialization. For LPDDR4, this bit ca
                #  be used to program additional mode registers before automatic SDRAM initialization if necessary. Note: This must be cleared 
                # o 0 after completing Software operation. Otherwise, SDRAM initialization routine will not re-start. - 0 - Software interventi
                # n is not allowed - 1 - Software intervention is allowed
                # PSU_DDRC_MRCTRL0_SW_INIT_INT                                                    0x0

                # Indicates whether the mode register operation is MRS in PDA mode or not - 0 - MRS - 1 - MRS in Per DRAM Addressability mode
                # PSU_DDRC_MRCTRL0_PDA_EN                                                         0x0

                # Indicates whether the mode register operation is MRS or WR/RD for MPR (only supported for DDR4) - 0 - MRS - 1 - WR/RD for MPR
                # PSU_DDRC_MRCTRL0_MPR_EN                                                         0x0

                # Indicates whether the mode register operation is read or write. Only used for LPDDR2/LPDDR3/LPDDR4/DDR4. - 0 - Write - 1 - Re
                # d
                # PSU_DDRC_MRCTRL0_MR_TYPE                                                        0x0

                # Mode Register Read/Write Control Register 0. Note: Do not enable more than one of the following fields simultaneously: - sw_i
                # it_int - pda_en - mpr_en
                #(OFFSET, MASK, VALUE)      (0XFD070010, 0x8000F03FU ,0x00000030U)  */
    mask_write 0XFD070010 0x8000F03F 0x00000030
                # Register : DERATEEN @ 0XFD070020</p>

                # Derate value of tRC for LPDDR4 - 0 - Derating uses +1. - 1 - Derating uses +2. - 2 - Derating uses +3. - 3 - Derating uses +4
                #  Present only in designs configured to support LPDDR4. The required number of cycles for derating can be determined by dividi
                # g 3.75ns by the core_ddrc_core_clk period, and rounding up the next integer.
                # PSU_DDRC_DERATEEN_RC_DERATE_VALUE                                               0x3

                # Derate byte Present only in designs configured to support LPDDR2/LPDDR3/LPDDR4 Indicates which byte of the MRR data is used f
                # r derating. The maximum valid value depends on MEMC_DRAM_TOTAL_DATA_WIDTH.
                # PSU_DDRC_DERATEEN_DERATE_BYTE                                                   0x0

                # Derate value - 0 - Derating uses +1. - 1 - Derating uses +2. Present only in designs configured to support LPDDR2/LPDDR3/LPDD
                # 4 Set to 0 for all LPDDR2 speed grades as derating value of +1.875 ns is less than a core_ddrc_core_clk period. Can be 0 or 1
                # for LPDDR3/LPDDR4, depending if +1.875 ns is less than a core_ddrc_core_clk period or not.
                # PSU_DDRC_DERATEEN_DERATE_VALUE                                                  0x0

                # Enables derating - 0 - Timing parameter derating is disabled - 1 - Timing parameter derating is enabled using MR4 read value.
                # Present only in designs configured to support LPDDR2/LPDDR3/LPDDR4 This field must be set to '0' for non-LPDDR2/LPDDR3/LPDDR4
                # mode.
                # PSU_DDRC_DERATEEN_DERATE_ENABLE                                                 0x0

                # Temperature Derate Enable Register
                #(OFFSET, MASK, VALUE)      (0XFD070020, 0x000003F3U ,0x00000300U)  */
    mask_write 0XFD070020 0x000003F3 0x00000300
                # Register : DERATEINT @ 0XFD070024</p>

                # Interval between two MR4 reads, used to derate the timing parameters. Present only in designs configured to support LPDDR2/LP
                # DR3/LPDDR4. This register must not be set to zero
                # PSU_DDRC_DERATEINT_MR4_READ_INTERVAL                                            0x800000

                # Temperature Derate Interval Register
                #(OFFSET, MASK, VALUE)      (0XFD070024, 0xFFFFFFFFU ,0x00800000U)  */
    mask_write 0XFD070024 0xFFFFFFFF 0x00800000
                # Register : PWRCTL @ 0XFD070030</p>

                # Self refresh state is an intermediate state to enter to Self refresh power down state or exit Self refresh power down state f
                # r LPDDR4. This register controls transition from the Self refresh state. - 1 - Prohibit transition from Self refresh state - 
                #  - Allow transition from Self refresh state
                # PSU_DDRC_PWRCTL_STAY_IN_SELFREF                                                 0x0

                # A value of 1 to this register causes system to move to Self Refresh state immediately, as long as it is not in INIT or DPD/MP
                # M operating_mode. This is referred to as Software Entry/Exit to Self Refresh. - 1 - Software Entry to Self Refresh - 0 - Soft
                # are Exit from Self Refresh
                # PSU_DDRC_PWRCTL_SELFREF_SW                                                      0x0

                # When this is 1, the uMCTL2 puts the SDRAM into maximum power saving mode when the transaction store is empty. This register m
                # st be reset to '0' to bring uMCTL2 out of maximum power saving mode. Present only in designs configured to support DDR4. For 
                # on-DDR4, this register should not be set to 1. Note that MPSM is not supported when using a DWC DDR PHY, if the PHY parameter
                # DWC_AC_CS_USE is disabled, as the MPSM exit sequence requires the chip-select signal to toggle. FOR PERFORMANCE ONLY.
                # PSU_DDRC_PWRCTL_MPSM_EN                                                         0x0

                # Enable the assertion of dfi_dram_clk_disable whenever a clock is not required by the SDRAM. If set to 0, dfi_dram_clk_disable
                # is never asserted. Assertion of dfi_dram_clk_disable is as follows: In DDR2/DDR3, can only be asserted in Self Refresh. In DD
                # 4, can be asserted in following: - in Self Refresh. - in Maximum Power Saving Mode In mDDR/LPDDR2/LPDDR3, can be asserted in 
                # ollowing: - in Self Refresh - in Power Down - in Deep Power Down - during Normal operation (Clock Stop) In LPDDR4, can be ass
                # rted in following: - in Self Refresh Power Down - in Power Down - during Normal operation (Clock Stop)
                # PSU_DDRC_PWRCTL_EN_DFI_DRAM_CLK_DISABLE                                         0x0

                # When this is 1, uMCTL2 puts the SDRAM into deep power-down mode when the transaction store is empty. This register must be re
                # et to '0' to bring uMCTL2 out of deep power-down mode. Controller performs automatic SDRAM initialization on deep power-down 
                # xit. Present only in designs configured to support mDDR or LPDDR2 or LPDDR3. For non-mDDR/non-LPDDR2/non-LPDDR3, this registe
                #  should not be set to 1. FOR PERFORMANCE ONLY.
                # PSU_DDRC_PWRCTL_DEEPPOWERDOWN_EN                                                0x0

                # If true then the uMCTL2 goes into power-down after a programmable number of cycles 'maximum idle clocks before power down' (P
                # RTMG.powerdown_to_x32). This register bit may be re-programmed during the course of normal operation.
                # PSU_DDRC_PWRCTL_POWERDOWN_EN                                                    0x0

                # If true then the uMCTL2 puts the SDRAM into Self Refresh after a programmable number of cycles 'maximum idle clocks before Se
                # f Refresh (PWRTMG.selfref_to_x32)'. This register bit may be re-programmed during the course of normal operation.
                # PSU_DDRC_PWRCTL_SELFREF_EN                                                      0x0

                # Low Power Control Register
                #(OFFSET, MASK, VALUE)      (0XFD070030, 0x0000007FU ,0x00000000U)  */
    mask_write 0XFD070030 0x0000007F 0x00000000
                # Register : PWRTMG @ 0XFD070034</p>

                # After this many clocks of NOP or deselect the uMCTL2 automatically puts the SDRAM into Self Refresh. This must be enabled in 
                # he PWRCTL.selfref_en. Unit: Multiples of 32 clocks. FOR PERFORMANCE ONLY.
                # PSU_DDRC_PWRTMG_SELFREF_TO_X32                                                  0x40

                # Minimum deep power-down time. For mDDR, value from the JEDEC specification is 0 as mDDR exits from deep power-down mode immed
                # ately after PWRCTL.deeppowerdown_en is de-asserted. For LPDDR2/LPDDR3, value from the JEDEC specification is 500us. Unit: Mul
                # iples of 4096 clocks. Present only in designs configured to support mDDR, LPDDR2 or LPDDR3. FOR PERFORMANCE ONLY.
                # PSU_DDRC_PWRTMG_T_DPD_X4096                                                     0x84

                # After this many clocks of NOP or deselect the uMCTL2 automatically puts the SDRAM into power-down. This must be enabled in th
                #  PWRCTL.powerdown_en. Unit: Multiples of 32 clocks FOR PERFORMANCE ONLY.
                # PSU_DDRC_PWRTMG_POWERDOWN_TO_X32                                                0x10

                # Low Power Timing Register
                #(OFFSET, MASK, VALUE)      (0XFD070034, 0x00FFFF1FU ,0x00408410U)  */
    mask_write 0XFD070034 0x00FFFF1F 0x00408410
                # Register : RFSHCTL0 @ 0XFD070050</p>

                # Threshold value in number of clock cycles before the critical refresh or page timer expires. A critical refresh is to be issu
                # d before this threshold is reached. It is recommended that this not be changed from the default value, currently shown as 0x2
                #  It must always be less than internally used t_rfc_nom_x32. Note that, in LPDDR2/LPDDR3/LPDDR4, internally used t_rfc_nom_x32
                # may be equal to RFSHTMG.t_rfc_nom_x32>>2 if derating is enabled (DERATEEN.derate_enable=1). Otherwise, internally used t_rfc_
                # om_x32 will be equal to RFSHTMG.t_rfc_nom_x32. Unit: Multiples of 32 clocks.
                # PSU_DDRC_RFSHCTL0_REFRESH_MARGIN                                                0x2

                # If the refresh timer (tRFCnom, also known as tREFI) has expired at least once, but it has not expired (RFSHCTL0.refresh_burst
                # 1) times yet, then a speculative refresh may be performed. A speculative refresh is a refresh performed at a time when refres
                #  would be useful, but before it is absolutely required. When the SDRAM bus is idle for a period of time determined by this RF
                # HCTL0.refresh_to_x32 and the refresh timer has expired at least once since the last refresh, then a speculative refresh is pe
                # formed. Speculative refreshes continues successively until there are no refreshes pending or until new reads or writes are is
                # ued to the uMCTL2. FOR PERFORMANCE ONLY.
                # PSU_DDRC_RFSHCTL0_REFRESH_TO_X32                                                0x10

                # The programmed value + 1 is the number of refresh timeouts that is allowed to accumulate before traffic is blocked and the re
                # reshes are forced to execute. Closing pages to perform a refresh is a one-time penalty that must be paid for each group of re
                # reshes. Therefore, performing refreshes in a burst reduces the per-refresh penalty of these page closings. Higher numbers for
                # RFSHCTL.refresh_burst slightly increases utilization; lower numbers decreases the worst-case latency associated with refreshe
                # . - 0 - single refresh - 1 - burst-of-2 refresh - 7 - burst-of-8 refresh For information on burst refresh feature refer to se
                # tion 3.9 of DDR2 JEDEC specification - JESD79-2F.pdf. For DDR2/3, the refresh is always per-rank and not per-bank. The rank r
                # fresh can be accumulated over 8*tREFI cycles using the burst refresh feature. In DDR4 mode, according to Fine Granularity fea
                # ure, 8 refreshes can be postponed in 1X mode, 16 refreshes in 2X mode and 32 refreshes in 4X mode. If using PHY-initiated upd
                # tes, care must be taken in the setting of RFSHCTL0.refresh_burst, to ensure that tRFCmax is not violated due to a PHY-initiat
                # d update occurring shortly before a refresh burst was due. In this situation, the refresh burst will be delayed until the PHY
                # initiated update is complete.
                # PSU_DDRC_RFSHCTL0_REFRESH_BURST                                                 0x0

                # - 1 - Per bank refresh; - 0 - All bank refresh. Per bank refresh allows traffic to flow to other banks. Per bank refresh is n
                # t supported by all LPDDR2 devices but should be supported by all LPDDR3/LPDDR4 devices. Present only in designs configured to
                # support LPDDR2/LPDDR3/LPDDR4
                # PSU_DDRC_RFSHCTL0_PER_BANK_REFRESH                                              0x0

                # Refresh Control Register 0
                #(OFFSET, MASK, VALUE)      (0XFD070050, 0x00F1F1F4U ,0x00210000U)  */
    mask_write 0XFD070050 0x00F1F1F4 0x00210000
                # Register : RFSHCTL3 @ 0XFD070060</p>

                # Fine Granularity Refresh Mode - 000 - Fixed 1x (Normal mode) - 001 - Fixed 2x - 010 - Fixed 4x - 101 - Enable on the fly 2x (
                # ot supported) - 110 - Enable on the fly 4x (not supported) - Everything else - reserved Note: The on-the-fly modes is not sup
                # orted in this version of the uMCTL2. Note: This must be set up while the Controller is in reset or while the Controller is in
                # self-refresh mode. Changing this during normal operation is not allowed. Making this a dynamic register will be supported in 
                # uture version of the uMCTL2.
                # PSU_DDRC_RFSHCTL3_REFRESH_MODE                                                  0x0

                # Toggle this signal (either from 0 to 1 or from 1 to 0) to indicate that the refresh register(s) have been updated. The value 
                # s automatically updated when exiting reset, so it does not need to be toggled initially.
                # PSU_DDRC_RFSHCTL3_REFRESH_UPDATE_LEVEL                                          0x0

                # When '1', disable auto-refresh generated by the uMCTL2. When auto-refresh is disabled, the SoC core must generate refreshes u
                # ing the registers reg_ddrc_rank0_refresh, reg_ddrc_rank1_refresh, reg_ddrc_rank2_refresh and reg_ddrc_rank3_refresh. When dis
                # auto_refresh transitions from 0 to 1, any pending refreshes are immediately scheduled by the uMCTL2. If DDR4 CRC/parity retry
                # is enabled (CRCPARCTL1.crc_parity_retry_enable = 1), disable auto-refresh is not supported, and this bit must be set to '0'. 
                # his register field is changeable on the fly.
                # PSU_DDRC_RFSHCTL3_DIS_AUTO_REFRESH                                              0x1

                # Refresh Control Register 3
                #(OFFSET, MASK, VALUE)      (0XFD070060, 0x00000073U ,0x00000001U)  */
    mask_write 0XFD070060 0x00000073 0x00000001
                # Register : RFSHTMG @ 0XFD070064</p>

                # tREFI: Average time interval between refreshes per rank (Specification: 7.8us for DDR2, DDR3 and DDR4. See JEDEC specificatio
                #  for mDDR, LPDDR2, LPDDR3 and LPDDR4). For LPDDR2/LPDDR3/LPDDR4: - if using all-bank refreshes (RFSHCTL0.per_bank_refresh = 0
                # , this register should be set to tREFIab - if using per-bank refreshes (RFSHCTL0.per_bank_refresh = 1), this register should 
                # e set to tREFIpb For configurations with MEMC_FREQ_RATIO=2, program this to (tREFI/2), no rounding up. In DDR4 mode, tREFI va
                # ue is different depending on the refresh mode. The user should program the appropriate value from the spec based on the value
                # programmed in the refresh mode register. Note that RFSHTMG.t_rfc_nom_x32 * 32 must be greater than RFSHTMG.t_rfc_min, and RFS
                # TMG.t_rfc_nom_x32 must be greater than 0x1. Unit: Multiples of 32 clocks.
                # PSU_DDRC_RFSHTMG_T_RFC_NOM_X32                                                  0x82

                # Used only when LPDDR3 memory type is connected. Should only be changed when uMCTL2 is in reset. Specifies whether to use the 
                # REFBW parameter (required by some LPDDR3 devices which comply with earlier versions of the LPDDR3 JEDEC specification) or not
                #  - 0 - tREFBW parameter not used - 1 - tREFBW parameter used
                # PSU_DDRC_RFSHTMG_LPDDR3_TREFBW_EN                                               0x1

                # tRFC (min): Minimum time from refresh to refresh or activate. For MEMC_FREQ_RATIO=1 configurations, t_rfc_min should be set t
                #  RoundUp(tRFCmin/tCK). For MEMC_FREQ_RATIO=2 configurations, t_rfc_min should be set to RoundUp(RoundUp(tRFCmin/tCK)/2). In L
                # DDR2/LPDDR3/LPDDR4 mode: - if using all-bank refreshes, the tRFCmin value in the above equations is equal to tRFCab - if usin
                #  per-bank refreshes, the tRFCmin value in the above equations is equal to tRFCpb In DDR4 mode, the tRFCmin value in the above
                # equations is different depending on the refresh mode (fixed 1X,2X,4X) and the device density. The user should program the app
                # opriate value from the spec based on the 'refresh_mode' and the device density that is used. Unit: Clocks.
                # PSU_DDRC_RFSHTMG_T_RFC_MIN                                                      0x8b

                # Refresh Timing Register
                #(OFFSET, MASK, VALUE)      (0XFD070064, 0x0FFF83FFU ,0x0082808BU)  */
    mask_write 0XFD070064 0x0FFF83FF 0x0082808B
                # Register : ECCCFG0 @ 0XFD070070</p>

                # Disable ECC scrubs. Valid only when ECCCFG0.ecc_mode = 3'b100 and MEMC_USE_RMW is defined
                # PSU_DDRC_ECCCFG0_DIS_SCRUB                                                      0x1

                # ECC mode indicator - 000 - ECC disabled - 100 - ECC enabled - SEC/DED over 1 beat - all other settings are reserved for futur
                #  use
                # PSU_DDRC_ECCCFG0_ECC_MODE                                                       0x0

                # ECC Configuration Register 0
                #(OFFSET, MASK, VALUE)      (0XFD070070, 0x00000017U ,0x00000010U)  */
    mask_write 0XFD070070 0x00000017 0x00000010
                # Register : ECCCFG1 @ 0XFD070074</p>

                # Selects whether to poison 1 or 2 bits - if 0 -> 2-bit (uncorrectable) data poisoning, if 1 -> 1-bit (correctable) data poison
                # ng, if ECCCFG1.data_poison_en=1
                # PSU_DDRC_ECCCFG1_DATA_POISON_BIT                                                0x0

                # Enable ECC data poisoning - introduces ECC errors on writes to address specified by the ECCPOISONADDR0/1 registers
                # PSU_DDRC_ECCCFG1_DATA_POISON_EN                                                 0x0

                # ECC Configuration Register 1
                #(OFFSET, MASK, VALUE)      (0XFD070074, 0x00000003U ,0x00000000U)  */
    mask_write 0XFD070074 0x00000003 0x00000000
                # Register : CRCPARCTL1 @ 0XFD0700C4</p>

                # The maximum number of DFI PHY clock cycles allowed from the assertion of the dfi_rddata_en signal to the assertion of each of
                # the corresponding bits of the dfi_rddata_valid signal. This corresponds to the DFI timing parameter tphy_rdlat. Refer to PHY 
                # pecification for correct value. This value it only used for detecting read data timeout when DDR4 retry is enabled by CRCPARC
                # L1.crc_parity_retry_enable=1. Maximum supported value: - 1:1 Frequency mode : DFITMG0.dfi_t_rddata_en + CRCPARCTL1.dfi_t_phy_
                # dlat < 'd114 - 1:2 Frequency mode ANDAND DFITMG0.dfi_rddata_use_sdr == 1 : CRCPARCTL1.dfi_t_phy_rdlat < 64 - 1:2 Frequency mo
                # e ANDAND DFITMG0.dfi_rddata_use_sdr == 0 : DFITMG0.dfi_t_rddata_en + CRCPARCTL1.dfi_t_phy_rdlat < 'd114 Unit: DFI Clocks
                # PSU_DDRC_CRCPARCTL1_DFI_T_PHY_RDLAT                                             0x10

                # After a Parity or CRC error is flagged on dfi_alert_n signal, the software has an option to read the mode registers in the DR
                # M before the hardware begins the retry process - 1: Wait for software to read/write the mode registers before hardware begins
                # the retry. After software is done with its operations, it will clear the alert interrupt register bit - 0: Hardware can begin
                # the retry right away after the dfi_alert_n pulse goes away. The value on this register is valid only when retry is enabled (P
                # RCTRL.crc_parity_retry_enable = 1) If this register is set to 1 and if the software doesn't clear the interrupt register afte
                #  handling the parity/CRC error, then the hardware will not begin the retry process and the system will hang. In the case of P
                # rity/CRC error, there are two possibilities when the software doesn't reset MR5[4] to 0. - (i) If 'Persistent parity' mode re
                # ister bit is NOT set: the commands sent during retry and normal operation are executed without parity checking. The value in 
                # he Parity error log register MPR Page 1 is valid. - (ii) If 'Persistent parity' mode register bit is SET: Parity checking is 
                # one for commands sent during retry and normal operation. If multiple errors occur before MR5[4] is cleared, the error log in 
                # PR Page 1 should be treated as 'Don't care'.
                # PSU_DDRC_CRCPARCTL1_ALERT_WAIT_FOR_SW                                           0x1

                # - 1: Enable command retry mechanism in case of C/A Parity or CRC error - 0: Disable command retry mechanism when C/A Parity o
                #  CRC features are enabled. Note that retry functionality is not supported if burst chop is enabled (MSTR.burstchop = 1) and/o
                #  disable auto-refresh is enabled (RFSHCTL3.dis_auto_refresh = 1)
                # PSU_DDRC_CRCPARCTL1_CRC_PARITY_RETRY_ENABLE                                     0x0

                # CRC Calculation setting register - 1: CRC includes DM signal - 0: CRC not includes DM signal Present only in designs configur
                # d to support DDR4.
                # PSU_DDRC_CRCPARCTL1_CRC_INC_DM                                                  0x0

                # CRC enable Register - 1: Enable generation of CRC - 0: Disable generation of CRC The setting of this register should match th
                #  CRC mode register setting in the DRAM.
                # PSU_DDRC_CRCPARCTL1_CRC_ENABLE                                                  0x0

                # C/A Parity enable register - 1: Enable generation of C/A parity and detection of C/A parity error - 0: Disable generation of 
                # /A parity and disable detection of C/A parity error If RCD's parity error detection or SDRAM's parity detection is enabled, t
                # is register should be 1.
                # PSU_DDRC_CRCPARCTL1_PARITY_ENABLE                                               0x0

                # CRC Parity Control Register1
                #(OFFSET, MASK, VALUE)      (0XFD0700C4, 0x3F000391U ,0x10000200U)  */
    mask_write 0XFD0700C4 0x3F000391 0x10000200
                # Register : CRCPARCTL2 @ 0XFD0700C8</p>

                # Value from the DRAM spec indicating the maximum width of the dfi_alert_n pulse when a parity error occurs. Recommended values
                #  - tPAR_ALERT_PW.MAX For configurations with MEMC_FREQ_RATIO=2, program this to tPAR_ALERT_PW.MAX/2 and round up to next inte
                # er value. Values of 0, 1 and 2 are illegal. This value must be greater than CRCPARCTL2.t_crc_alert_pw_max.
                # PSU_DDRC_CRCPARCTL2_T_PAR_ALERT_PW_MAX                                          0x40

                # Value from the DRAM spec indicating the maximum width of the dfi_alert_n pulse when a CRC error occurs. Recommended values: -
                # tCRC_ALERT_PW.MAX For configurations with MEMC_FREQ_RATIO=2, program this to tCRC_ALERT_PW.MAX/2 and round up to next integer
                # value. Values of 0, 1 and 2 are illegal. This value must be less than CRCPARCTL2.t_par_alert_pw_max.
                # PSU_DDRC_CRCPARCTL2_T_CRC_ALERT_PW_MAX                                          0x5

                # Indicates the maximum duration in number of DRAM clock cycles for which a command should be held in the Command Retry FIFO be
                # ore it is popped out. Every location in the Command Retry FIFO has an associated down counting timer that will use this regis
                # er as the start value. The down counting starts when a command is loaded into the FIFO. The timer counts down every 4 DRAM cy
                # les. When the counter reaches zero, the entry is popped from the FIFO. All the counters are frozen, if a C/A Parity or CRC er
                # or occurs before the counter reaches zero. The counter is reset to 0, after all the commands in the FIFO are retried. Recomme
                # ded(minimum) values: - Only C/A Parity is enabled. RoundUp((PHY Command Latency(DRAM CLK) + CAL + RDIMM delay + tPAR_ALERT_ON
                # max + tPAR_UNKNOWN + PHY Alert Latency(DRAM CLK) + board delay) / 4) + 2 - Both C/A Parity and CRC is enabled/ Only CRC is en
                # bled. RoundUp((PHY Command Latency(DRAM CLK) + CAL + RDIMM delay + WL + 5(BL10)+ tCRC_ALERT.max + PHY Alert Latency(DRAM CLK)
                # + board delay) / 4) + 2 Note 1: All value (e.g. tPAR_ALERT_ON) should be in terms of DRAM Clock and round up Note 2: Board de
                # ay(Command/Alert_n) should be considered. Note 3: Use the worst case(longer) value for PHY Latencies/Board delay Note 4: The 
                # ecommended values are minimum value to be set. For mode detail, See 'Calculation of FIFO Depth' section. Max value can be set
                # to this register is defined below: - MEMC_BURST_LENGTH == 16 Full bus Mode (CRC=OFF) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-
                #  Full bus Mode (CRC=ON) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-3 Half bus Mode (CRC=OFF) Max value = UMCTL2_RETRY_CMD_FIFO_D
                # PTH-4 Half bus Mode (CRC=ON) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-6 Quarter bus Mode (CRC=OFF) Max value = UMCTL2_RETRY_CM
                # _FIFO_DEPTH-8 Quarter bus Mode (CRC=ON) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-12 - MEMC_BURST_LENGTH != 16 Full bus Mode (C
                # C=OFF) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-1 Full bus Mode (CRC=ON) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-2 Half bus Mo
                # e (CRC=OFF) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-2 Half bus Mode (CRC=ON) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-3 Quarte
                #  bus Mode (CRC=OFF) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-4 Quarter bus Mode (CRC=ON) Max value = UMCTL2_RETRY_CMD_FIFO_DEP
                # H-6 Values of 0, 1 and 2 are illegal.
                # PSU_DDRC_CRCPARCTL2_RETRY_FIFO_MAX_HOLD_TIMER_X4                                0x1f

                # CRC Parity Control Register2
                #(OFFSET, MASK, VALUE)      (0XFD0700C8, 0x01FF1F3FU ,0x0040051FU)  */
    mask_write 0XFD0700C8 0x01FF1F3F 0x0040051F
                # Register : INIT0 @ 0XFD0700D0</p>

                # If lower bit is enabled the SDRAM initialization routine is skipped. The upper bit decides what state the controller starts u
                #  in when reset is removed - 00 - SDRAM Intialization routine is run after power-up - 01 - SDRAM Intialization routine is skip
                # ed after power-up. Controller starts up in Normal Mode - 11 - SDRAM Intialization routine is skipped after power-up. Controll
                # r starts up in Self-refresh Mode - 10 - SDRAM Intialization routine is run after power-up. Note: The only 2'b00 is supported 
                # or LPDDR4 in this version of the uMCTL2.
                # PSU_DDRC_INIT0_SKIP_DRAM_INIT                                                   0x0

                # Cycles to wait after driving CKE high to start the SDRAM initialization sequence. Unit: 1024 clocks. DDR2 typically requires 
                #  400 ns delay, requiring this value to be programmed to 2 at all clock speeds. LPDDR2/LPDDR3 typically requires this to be pr
                # grammed for a delay of 200 us. LPDDR4 typically requires this to be programmed for a delay of 2 us. For configurations with M
                # MC_FREQ_RATIO=2, program this to JEDEC spec value divided by 2, and round it up to next integer value.
                # PSU_DDRC_INIT0_POST_CKE_X1024                                                   0x2

                # Cycles to wait after reset before driving CKE high to start the SDRAM initialization sequence. Unit: 1024 clock cycles. DDR2 
                # pecifications typically require this to be programmed for a delay of >= 200 us. LPDDR2/LPDDR3: tINIT1 of 100 ns (min) LPDDR4:
                # tINIT3 of 2 ms (min) For configurations with MEMC_FREQ_RATIO=2, program this to JEDEC spec value divided by 2, and round it u
                #  to next integer value.
                # PSU_DDRC_INIT0_PRE_CKE_X1024                                                    0x106

                # SDRAM Initialization Register 0
                #(OFFSET, MASK, VALUE)      (0XFD0700D0, 0xC3FF0FFFU ,0x00020106U)  */
    mask_write 0XFD0700D0 0xC3FF0FFF 0x00020106
                # Register : INIT1 @ 0XFD0700D4</p>

                # Number of cycles to assert SDRAM reset signal during init sequence. This is only present for designs supporting DDR3, DDR4 or
                # LPDDR4 devices. For use with a DDR PHY, this should be set to a minimum of 1
                # PSU_DDRC_INIT1_DRAM_RSTN_X1024                                                  0x2

                # Cycles to wait after completing the SDRAM initialization sequence before starting the dynamic scheduler. Unit: Counts of a gl
                # bal timer that pulses every 32 clock cycles. There is no known specific requirement for this; it may be set to zero.
                # PSU_DDRC_INIT1_FINAL_WAIT_X32                                                   0x0

                # Wait period before driving the OCD complete command to SDRAM. Unit: Counts of a global timer that pulses every 32 clock cycle
                # . There is no known specific requirement for this; it may be set to zero.
                # PSU_DDRC_INIT1_PRE_OCD_X32                                                      0x0

                # SDRAM Initialization Register 1
                #(OFFSET, MASK, VALUE)      (0XFD0700D4, 0x01FF7F0FU ,0x00020000U)  */
    mask_write 0XFD0700D4 0x01FF7F0F 0x00020000
                # Register : INIT2 @ 0XFD0700D8</p>

                # Idle time after the reset command, tINIT4. Present only in designs configured to support LPDDR2. Unit: 32 clock cycles.
                # PSU_DDRC_INIT2_IDLE_AFTER_RESET_X32                                             0x23

                # Time to wait after the first CKE high, tINIT2. Present only in designs configured to support LPDDR2/LPDDR3. Unit: 1 clock cyc
                # e. LPDDR2/LPDDR3 typically requires 5 x tCK delay.
                # PSU_DDRC_INIT2_MIN_STABLE_CLOCK_X1                                              0x5

                # SDRAM Initialization Register 2
                #(OFFSET, MASK, VALUE)      (0XFD0700D8, 0x0000FF0FU ,0x00002305U)  */
    mask_write 0XFD0700D8 0x0000FF0F 0x00002305
                # Register : INIT3 @ 0XFD0700DC</p>

                # DDR2: Value to write to MR register. Bit 8 is for DLL and the setting here is ignored. The uMCTL2 sets this bit appropriately
                #  DDR3/DDR4: Value loaded into MR0 register. mDDR: Value to write to MR register. LPDDR2/LPDDR3/LPDDR4 - Value to write to MR1
                # register
                # PSU_DDRC_INIT3_MR                                                               0x930

                # DDR2: Value to write to EMR register. Bits 9:7 are for OCD and the setting in this register is ignored. The uMCTL2 sets those
                # bits appropriately. DDR3/DDR4: Value to write to MR1 register Set bit 7 to 0. If PHY-evaluation mode training is enabled, thi
                #  bit is set appropriately by the uMCTL2 during write leveling. mDDR: Value to write to EMR register. LPDDR2/LPDDR3/LPDDR4 - V
                # lue to write to MR2 register
                # PSU_DDRC_INIT3_EMR                                                              0x301

                # SDRAM Initialization Register 3
                #(OFFSET, MASK, VALUE)      (0XFD0700DC, 0xFFFFFFFFU ,0x09300301U)  */
    mask_write 0XFD0700DC 0xFFFFFFFF 0x09300301
                # Register : INIT4 @ 0XFD0700E0</p>

                # DDR2: Value to write to EMR2 register. DDR3/DDR4: Value to write to MR2 register LPDDR2/LPDDR3/LPDDR4: Value to write to MR3 
                # egister mDDR: Unused
                # PSU_DDRC_INIT4_EMR2                                                             0x20

                # DDR2: Value to write to EMR3 register. DDR3/DDR4: Value to write to MR3 register mDDR/LPDDR2/LPDDR3: Unused LPDDR4: Value to 
                # rite to MR13 register
                # PSU_DDRC_INIT4_EMR3                                                             0x200

                # SDRAM Initialization Register 4
                #(OFFSET, MASK, VALUE)      (0XFD0700E0, 0xFFFFFFFFU ,0x00200200U)  */
    mask_write 0XFD0700E0 0xFFFFFFFF 0x00200200
                # Register : INIT5 @ 0XFD0700E4</p>

                # ZQ initial calibration, tZQINIT. Present only in designs configured to support DDR3 or DDR4 or LPDDR2/LPDDR3. Unit: 32 clock 
                # ycles. DDR3 typically requires 512 clocks. DDR4 requires 1024 clocks. LPDDR2/LPDDR3 requires 1 us.
                # PSU_DDRC_INIT5_DEV_ZQINIT_X32                                                   0x21

                # Maximum duration of the auto initialization, tINIT5. Present only in designs configured to support LPDDR2/LPDDR3. LPDDR2/LPDD
                # 3 typically requires 10 us.
                # PSU_DDRC_INIT5_MAX_AUTO_INIT_X1024                                              0x4

                # SDRAM Initialization Register 5
                #(OFFSET, MASK, VALUE)      (0XFD0700E4, 0x00FF03FFU ,0x00210004U)  */
    mask_write 0XFD0700E4 0x00FF03FF 0x00210004
                # Register : INIT6 @ 0XFD0700E8</p>

                # DDR4- Value to be loaded into SDRAM MR4 registers. Used in DDR4 designs only.
                # PSU_DDRC_INIT6_MR4                                                              0x0

                # DDR4- Value to be loaded into SDRAM MR5 registers. Used in DDR4 designs only.
                # PSU_DDRC_INIT6_MR5                                                              0x6c0

                # SDRAM Initialization Register 6
                #(OFFSET, MASK, VALUE)      (0XFD0700E8, 0xFFFFFFFFU ,0x000006C0U)  */
    mask_write 0XFD0700E8 0xFFFFFFFF 0x000006C0
                # Register : INIT7 @ 0XFD0700EC</p>

                # DDR4- Value to be loaded into SDRAM MR6 registers. Used in DDR4 designs only.
                # PSU_DDRC_INIT7_MR6                                                              0x819

                # SDRAM Initialization Register 7
                #(OFFSET, MASK, VALUE)      (0XFD0700EC, 0xFFFF0000U ,0x08190000U)  */
    mask_write 0XFD0700EC 0xFFFF0000 0x08190000
                # Register : DIMMCTL @ 0XFD0700F0</p>

                # Disabling Address Mirroring for BG bits. When this is set to 1, BG0 and BG1 are NOT swapped even if Address Mirroring is enab
                # ed. This will be required for DDR4 DIMMs with x16 devices. - 1 - BG0 and BG1 are NOT swapped. - 0 - BG0 and BG1 are swapped i
                #  address mirroring is enabled.
                # PSU_DDRC_DIMMCTL_DIMM_DIS_BG_MIRRORING                                          0x0

                # Enable for BG1 bit of MRS command. BG1 bit of the mode register address is specified as RFU (Reserved for Future Use) and mus
                #  be programmed to 0 during MRS. In case where DRAMs which do not have BG1 are attached and both the CA parity and the Output 
                # nversion are enabled, this must be set to 0, so that the calculation of CA parity will not include BG1 bit. Note: This has no
                # effect on the address of any other memory accesses, or of software-driven mode register accesses. If address mirroring is ena
                # led, this is applied to BG1 of even ranks and BG0 of odd ranks. - 1 - Enabled - 0 - Disabled
                # PSU_DDRC_DIMMCTL_MRS_BG1_EN                                                     0x1

                # Enable for A17 bit of MRS command. A17 bit of the mode register address is specified as RFU (Reserved for Future Use) and mus
                #  be programmed to 0 during MRS. In case where DRAMs which do not have A17 are attached and the Output Inversion are enabled, 
                # his must be set to 0, so that the calculation of CA parity will not include A17 bit. Note: This has no effect on the address 
                # f any other memory accesses, or of software-driven mode register accesses. - 1 - Enabled - 0 - Disabled
                # PSU_DDRC_DIMMCTL_MRS_A17_EN                                                     0x0

                # Output Inversion Enable (for DDR4 RDIMM implementations only). DDR4 RDIMM implements the Output Inversion feature by default,
                # which means that the following address, bank address and bank group bits of B-side DRAMs are inverted: A3-A9, A11, A13, A17, 
                # A0-BA1, BG0-BG1. Setting this bit ensures that, for mode register accesses generated by the uMCTL2 during the automatic initi
                # lization routine and enabling of a particular DDR4 feature, separate A-side and B-side mode register accesses are generated. 
                # or B-side mode register accesses, these bits are inverted within the uMCTL2 to compensate for this RDIMM inversion. Note: Thi
                #  has no effect on the address of any other memory accesses, or of software-driven mode register accesses. - 1 - Implement out
                # ut inversion for B-side DRAMs. - 0 - Do not implement output inversion for B-side DRAMs.
                # PSU_DDRC_DIMMCTL_DIMM_OUTPUT_INV_EN                                             0x0

                # Address Mirroring Enable (for multi-rank UDIMM implementations and multi-rank DDR4 RDIMM implementations). Some UDIMMs and DD
                # 4 RDIMMs implement address mirroring for odd ranks, which means that the following address, bank address and bank group bits 
                # re swapped: (A3, A4), (A5, A6), (A7, A8), (BA0, BA1) and also (A11, A13), (BG0, BG1) for the DDR4. Setting this bit ensures t
                # at, for mode register accesses during the automatic initialization routine, these bits are swapped within the uMCTL2 to compe
                # sate for this UDIMM/RDIMM swapping. In addition to the automatic initialization routine, in case of DDR4 UDIMM/RDIMM, they ar
                #  swapped during the automatic MRS access to enable/disable of a particular DDR4 feature. Note: This has no effect on the addr
                # ss of any other memory accesses, or of software-driven mode register accesses. This is not supported for mDDR, LPDDR2, LPDDR3
                # or LPDDR4 SDRAMs. Note: In case of x16 DDR4 DIMMs, BG1 output of MRS for the odd ranks is same as BG0 because BG1 is invalid,
                # hence dimm_dis_bg_mirroring register must be set to 1. - 1 - For odd ranks, implement address mirroring for MRS commands to d
                # ring initialization and for any automatic DDR4 MRS commands (to be used if UDIMM/RDIMM implements address mirroring) - 0 - Do
                # not implement address mirroring
                # PSU_DDRC_DIMMCTL_DIMM_ADDR_MIRR_EN                                              0x0

                # Staggering enable for multi-rank accesses (for multi-rank UDIMM and RDIMM implementations only). This is not supported for mD
                # R, LPDDR2, LPDDR3 or LPDDR4 SDRAMs. Note: Even if this bit is set it does not take care of software driven MR commands (via M
                # CTRL0/MRCTRL1), where software is responsible to send them to seperate ranks as appropriate. - 1 - (DDR4) Send MRS commands t
                #  each ranks seperately - 1 - (non-DDR4) Send all commands to even and odd ranks seperately - 0 - Do not stagger accesses
                # PSU_DDRC_DIMMCTL_DIMM_STAGGER_CS_EN                                             0x0

                # DIMM Control Register
                #(OFFSET, MASK, VALUE)      (0XFD0700F0, 0x0000003FU ,0x00000010U)  */
    mask_write 0XFD0700F0 0x0000003F 0x00000010
                # Register : RANKCTL @ 0XFD0700F4</p>

                # Only present for multi-rank configurations. Indicates the number of clocks of gap in data responses when performing consecuti
                # e writes to different ranks. This is used to switch the delays in the PHY to match the rank requirements. This value should c
                # nsider both PHY requirement and ODT requirement. - PHY requirement: tphy_wrcsgap + 1 (see PHY databook for value of tphy_wrcs
                # ap) If CRC feature is enabled, should be increased by 1. If write preamble is set to 2tCK(DDR4/LPDDR4 only), should be increa
                # ed by 1. If write postamble is set to 1.5tCK(LPDDR4 only), should be increased by 1. - ODT requirement: The value programmed 
                # n this register takes care of the ODT switch off timing requirement when switching ranks during writes. For LPDDR4, the requi
                # ement is ODTLoff - ODTLon - BL/2 + 1 For configurations with MEMC_FREQ_RATIO=1, program this to the larger of PHY requirement
                # or ODT requirement. For configurations with MEMC_FREQ_RATIO=2, program this to the larger value divided by two and round it u
                #  to the next integer.
                # PSU_DDRC_RANKCTL_DIFF_RANK_WR_GAP                                               0x6

                # Only present for multi-rank configurations. Indicates the number of clocks of gap in data responses when performing consecuti
                # e reads to different ranks. This is used to switch the delays in the PHY to match the rank requirements. This value should co
                # sider both PHY requirement and ODT requirement. - PHY requirement: tphy_rdcsgap + 1 (see PHY databook for value of tphy_rdcsg
                # p) If read preamble is set to 2tCK(DDR4/LPDDR4 only), should be increased by 1. If read postamble is set to 1.5tCK(LPDDR4 onl
                # ), should be increased by 1. - ODT requirement: The value programmed in this register takes care of the ODT switch off timing
                # requirement when switching ranks during reads. For configurations with MEMC_FREQ_RATIO=1, program this to the larger of PHY r
                # quirement or ODT requirement. For configurations with MEMC_FREQ_RATIO=2, program this to the larger value divided by two and 
                # ound it up to the next integer.
                # PSU_DDRC_RANKCTL_DIFF_RANK_RD_GAP                                               0x6

                # Only present for multi-rank configurations. Background: Reads to the same rank can be performed back-to-back. Reads to differ
                # nt ranks require additional gap dictated by the register RANKCTL.diff_rank_rd_gap. This is to avoid possible data bus content
                # on as well as to give PHY enough time to switch the delay when changing ranks. The uMCTL2 arbitrates for bus access on a cycl
                # -by-cycle basis; therefore after a read is scheduled, there are few clock cycles (determined by the value on RANKCTL.diff_ran
                # _rd_gap register) in which only reads from the same rank are eligible to be scheduled. This prevents reads from other ranks f
                # om having fair access to the data bus. This parameter represents the maximum number of reads that can be scheduled consecutiv
                # ly to the same rank. After this number is reached, a delay equal to RANKCTL.diff_rank_rd_gap is inserted by the scheduler to 
                # llow all ranks a fair opportunity to be scheduled. Higher numbers increase bandwidth utilization, lower numbers increase fair
                # ess. This feature can be DISABLED by setting this register to 0. When set to 0, the Controller will stay on the same rank as 
                # ong as commands are available for it. Minimum programmable value is 0 (feature disabled) and maximum programmable value is 0x
                # . FOR PERFORMANCE ONLY.
                # PSU_DDRC_RANKCTL_MAX_RANK_RD                                                    0xf

                # Rank Control Register
                #(OFFSET, MASK, VALUE)      (0XFD0700F4, 0x00000FFFU ,0x0000066FU)  */
    mask_write 0XFD0700F4 0x00000FFF 0x0000066F
                # Register : DRAMTMG0 @ 0XFD070100</p>

                # Minimum time between write and precharge to same bank. Unit: Clocks Specifications: WL + BL/2 + tWR = approximately 8 cycles 
                #  15 ns = 14 clocks @400MHz and less for lower frequencies where: - WL = write latency - BL = burst length. This must match th
                #  value programmed in the BL bit of the mode register to the SDRAM. BST (burst terminate) is not supported at present. - tWR =
                # Write recovery time. This comes directly from the SDRAM specification. Add one extra cycle for LPDDR2/LPDDR3/LPDDR4 for this 
                # arameter. For configurations with MEMC_FREQ_RATIO=2, 1T mode, divide the above value by 2. No rounding up. For configurations
                # with MEMC_FREQ_RATIO=2, 2T mode or LPDDR4 mode, divide the above value by 2 and round it up to the next integer value.
                # PSU_DDRC_DRAMTMG0_WR2PRE                                                        0x11

                # tFAW Valid only when 8 or more banks(or banks x bank groups) are present. In 8-bank design, at most 4 banks must be activated
                # in a rolling window of tFAW cycles. For configurations with MEMC_FREQ_RATIO=2, program this to (tFAW/2) and round up to next 
                # nteger value. In a 4-bank design, set this register to 0x1 independent of the MEMC_FREQ_RATIO configuration. Unit: Clocks
                # PSU_DDRC_DRAMTMG0_T_FAW                                                         0xc

                # tRAS(max): Maximum time between activate and precharge to same bank. This is the maximum time that a page can be kept open Mi
                # imum value of this register is 1. Zero is invalid. For configurations with MEMC_FREQ_RATIO=2, program this to (tRAS(max)-1)/2
                #  No rounding up. Unit: Multiples of 1024 clocks.
                # PSU_DDRC_DRAMTMG0_T_RAS_MAX                                                     0x24

                # tRAS(min): Minimum time between activate and precharge to the same bank. For configurations with MEMC_FREQ_RATIO=2, 1T mode, 
                # rogram this to tRAS(min)/2. No rounding up. For configurations with MEMC_FREQ_RATIO=2, 2T mode or LPDDR4 mode, program this t
                #  (tRAS(min)/2) and round it up to the next integer value. Unit: Clocks
                # PSU_DDRC_DRAMTMG0_T_RAS_MIN                                                     0x12

                # SDRAM Timing Register 0
                #(OFFSET, MASK, VALUE)      (0XFD070100, 0x7F3F7F3FU ,0x110C2412U)  */
    mask_write 0XFD070100 0x7F3F7F3F 0x110C2412
                # Register : DRAMTMG1 @ 0XFD070104</p>

                # tXP: Minimum time after power-down exit to any operation. For DDR3, this should be programmed to tXPDLL if slow powerdown exi
                #  is selected in MR0[12]. If C/A parity for DDR4 is used, set to (tXP+PL) instead. For configurations with MEMC_FREQ_RATIO=2, 
                # rogram this to (tXP/2) and round it up to the next integer value. Units: Clocks
                # PSU_DDRC_DRAMTMG1_T_XP                                                          0x4

                # tRTP: Minimum time from read to precharge of same bank. - DDR2: tAL + BL/2 + max(tRTP, 2) - 2 - DDR3: tAL + max (tRTP, 4) - D
                # R4: Max of following two equations: tAL + max (tRTP, 4) or, RL + BL/2 - tRP. - mDDR: BL/2 - LPDDR2: Depends on if it's LPDDR2
                # S2 or LPDDR2-S4: LPDDR2-S2: BL/2 + tRTP - 1. LPDDR2-S4: BL/2 + max(tRTP,2) - 2. - LPDDR3: BL/2 + max(tRTP,4) - 4 - LPDDR4: BL
                # 2 + max(tRTP,8) - 8 For configurations with MEMC_FREQ_RATIO=2, 1T mode, divide the above value by 2. No rounding up. For conf
                # gurations with MEMC_FREQ_RATIO=2, 2T mode or LPDDR4 mode, divide the above value by 2 and round it up to the next integer val
                # e. Unit: Clocks.
                # PSU_DDRC_DRAMTMG1_RD2PRE                                                        0x4

                # tRC: Minimum time between activates to same bank. For configurations with MEMC_FREQ_RATIO=2, program this to (tRC/2) and roun
                #  up to next integer value. Unit: Clocks.
                # PSU_DDRC_DRAMTMG1_T_RC                                                          0x19

                # SDRAM Timing Register 1
                #(OFFSET, MASK, VALUE)      (0XFD070104, 0x001F1F7FU ,0x00040419U)  */
    mask_write 0XFD070104 0x001F1F7F 0x00040419
                # Register : DRAMTMG2 @ 0XFD070108</p>

                # Set to WL Time from write command to write data on SDRAM interface. This must be set to WL. For mDDR, it should normally be s
                # t to 1. Note that, depending on the PHY, if using RDIMM, it may be necessary to use a value of WL + 1 to compensate for the e
                # tra cycle of latency through the RDIMM For configurations with MEMC_FREQ_RATIO=2, divide the value calculated using the above
                # equation by 2, and round it up to next integer. This register field is not required for DDR2 and DDR3 (except if MEMC_TRAININ
                #  is set), as the DFI read and write latencies defined in DFITMG0 and DFITMG1 are sufficient for those protocols Unit: clocks
                # PSU_DDRC_DRAMTMG2_WRITE_LATENCY                                                 0x7

                # Set to RL Time from read command to read data on SDRAM interface. This must be set to RL. Note that, depending on the PHY, if
                # using RDIMM, it mat be necessary to use a value of RL + 1 to compensate for the extra cycle of latency through the RDIMM For 
                # onfigurations with MEMC_FREQ_RATIO=2, divide the value calculated using the above equation by 2, and round it up to next inte
                # er. This register field is not required for DDR2 and DDR3 (except if MEMC_TRAINING is set), as the DFI read and write latenci
                # s defined in DFITMG0 and DFITMG1 are sufficient for those protocols Unit: clocks
                # PSU_DDRC_DRAMTMG2_READ_LATENCY                                                  0x8

                # DDR2/3/mDDR: RL + BL/2 + 2 - WL DDR4: RL + BL/2 + 1 + WR_PREAMBLE - WL LPDDR2/LPDDR3: RL + BL/2 + RU(tDQSCKmax/tCK) + 1 - WL 
                # PDDR4(DQ ODT is Disabled): RL + BL/2 + RU(tDQSCKmax/tCK) + WR_PREAMBLE + RD_POSTAMBLE - WL LPDDR4(DQ ODT is Enabled) : RL + B
                # /2 + RU(tDQSCKmax/tCK) + RD_POSTAMBLE - ODTLon - RU(tODTon(min)/tCK) Minimum time from read command to write command. Include
                # time for bus turnaround and all per-bank, per-rank, and global constraints. Unit: Clocks. Where: - WL = write latency - BL = 
                # urst length. This must match the value programmed in the BL bit of the mode register to the SDRAM - RL = read latency = CAS l
                # tency - WR_PREAMBLE = write preamble. This is unique to DDR4 and LPDDR4. - RD_POSTAMBLE = read postamble. This is unique to L
                # DDR4. For LPDDR2/LPDDR3/LPDDR4, if derating is enabled (DERATEEN.derate_enable=1), derated tDQSCKmax should be used. For conf
                # gurations with MEMC_FREQ_RATIO=2, divide the value calculated using the above equation by 2, and round it up to next integer.
                # PSU_DDRC_DRAMTMG2_RD2WR                                                         0x6

                # DDR4: CWL + PL + BL/2 + tWTR_L Others: CWL + BL/2 + tWTR In DDR4, minimum time from write command to read command for same ba
                # k group. In others, minimum time from write command to read command. Includes time for bus turnaround, recovery times, and al
                #  per-bank, per-rank, and global constraints. Unit: Clocks. Where: - CWL = CAS write latency - PL = Parity latency - BL = burs
                #  length. This must match the value programmed in the BL bit of the mode register to the SDRAM - tWTR_L = internal write to re
                # d command delay for same bank group. This comes directly from the SDRAM specification. - tWTR = internal write to read comman
                #  delay. This comes directly from the SDRAM specification. Add one extra cycle for LPDDR2/LPDDR3/LPDDR4 operation. For configu
                # ations with MEMC_FREQ_RATIO=2, divide the value calculated using the above equation by 2, and round it up to next integer.
                # PSU_DDRC_DRAMTMG2_WR2RD                                                         0xe

                # SDRAM Timing Register 2
                #(OFFSET, MASK, VALUE)      (0XFD070108, 0x3F3F3F3FU ,0x0708060EU)  */
    mask_write 0XFD070108 0x3F3F3F3F 0x0708060E
                # Register : DRAMTMG3 @ 0XFD07010C</p>

                # Time to wait after a mode register write or read (MRW or MRR). Present only in designs configured to support LPDDR2, LPDDR3 o
                #  LPDDR4. LPDDR2 typically requires value of 5. LPDDR3 typically requires value of 10. LPDDR4: Set this to the larger of tMRW 
                # nd tMRWCKEL. For LPDDR2, this register is used for the time from a MRW/MRR to all other commands. For LDPDR3, this register i
                #  used for the time from a MRW/MRR to a MRW/MRR.
                # PSU_DDRC_DRAMTMG3_T_MRW                                                         0x5

                # tMRD: Cycles to wait after a mode register write or read. Depending on the connected SDRAM, tMRD represents: DDR2/mDDR: Time 
                # rom MRS to any command DDR3/4: Time from MRS to MRS command LPDDR2: not used LPDDR3/4: Time from MRS to non-MRS command For c
                # nfigurations with MEMC_FREQ_RATIO=2, program this to (tMRD/2) and round it up to the next integer value. If C/A parity for DD
                # 4 is used, set to tMRD_PAR(tMOD+PL) instead.
                # PSU_DDRC_DRAMTMG3_T_MRD                                                         0x4

                # tMOD: Parameter used only in DDR3 and DDR4. Cycles between load mode command and following non-load mode command. If C/A pari
                # y for DDR4 is used, set to tMOD_PAR(tMOD+PL) instead. Set to tMOD if MEMC_FREQ_RATIO=1, or tMOD/2 (rounded up to next integer
                #  if MEMC_FREQ_RATIO=2. Note that if using RDIMM, depending on the PHY, it may be necessary to use a value of tMOD + 1 or (tMO
                #  + 1)/2 to compensate for the extra cycle of latency applied to mode register writes by the RDIMM chip.
                # PSU_DDRC_DRAMTMG3_T_MOD                                                         0xc

                # SDRAM Timing Register 3
                #(OFFSET, MASK, VALUE)      (0XFD07010C, 0x3FF3F3FFU ,0x0050400CU)  */
    mask_write 0XFD07010C 0x3FF3F3FF 0x0050400C
                # Register : DRAMTMG4 @ 0XFD070110</p>

                # tRCD - tAL: Minimum time from activate to read or write command to same bank. For configurations with MEMC_FREQ_RATIO=2, prog
                # am this to ((tRCD - tAL)/2) and round it up to the next integer value. Minimum value allowed for this register is 1, which im
                # lies minimum (tRCD - tAL) value to be 2 in configurations with MEMC_FREQ_RATIO=2. Unit: Clocks.
                # PSU_DDRC_DRAMTMG4_T_RCD                                                         0x8

                # DDR4: tCCD_L: This is the minimum time between two reads or two writes for same bank group. Others: tCCD: This is the minimum
                # time between two reads or two writes. For configurations with MEMC_FREQ_RATIO=2, program this to (tCCD_L/2 or tCCD/2) and rou
                # d it up to the next integer value. Unit: clocks.
                # PSU_DDRC_DRAMTMG4_T_CCD                                                         0x3

                # DDR4: tRRD_L: Minimum time between activates from bank 'a' to bank 'b' for same bank group. Others: tRRD: Minimum time betwee
                #  activates from bank 'a' to bank 'b'For configurations with MEMC_FREQ_RATIO=2, program this to (tRRD_L/2 or tRRD/2) and round
                # it up to the next integer value. Unit: Clocks.
                # PSU_DDRC_DRAMTMG4_T_RRD                                                         0x3

                # tRP: Minimum time from precharge to activate of same bank. For MEMC_FREQ_RATIO=1 configurations, t_rp should be set to RoundU
                # (tRP/tCK). For MEMC_FREQ_RATIO=2 configurations, t_rp should be set to RoundDown(RoundUp(tRP/tCK)/2) + 1. For MEMC_FREQ_RATIO
                # 2 configurations in LPDDR4, t_rp should be set to RoundUp(RoundUp(tRP/tCK)/2). Unit: Clocks.
                # PSU_DDRC_DRAMTMG4_T_RP                                                          0x9

                # SDRAM Timing Register 4
                #(OFFSET, MASK, VALUE)      (0XFD070110, 0x1F0F0F1FU ,0x08030309U)  */
    mask_write 0XFD070110 0x1F0F0F1F 0x08030309
                # Register : DRAMTMG5 @ 0XFD070114</p>

                # This is the time before Self Refresh Exit that CK is maintained as a valid clock before issuing SRX. Specifies the clock stab
                # e time before SRX. Recommended settings: - mDDR: 1 - LPDDR2: 2 - LPDDR3: 2 - LPDDR4: tCKCKEH - DDR2: 1 - DDR3: tCKSRX - DDR4:
                # tCKSRX For configurations with MEMC_FREQ_RATIO=2, program this to recommended value divided by two and round it up to next in
                # eger.
                # PSU_DDRC_DRAMTMG5_T_CKSRX                                                       0x6

                # This is the time after Self Refresh Down Entry that CK is maintained as a valid clock. Specifies the clock disable delay afte
                #  SRE. Recommended settings: - mDDR: 0 - LPDDR2: 2 - LPDDR3: 2 - LPDDR4: tCKCKEL - DDR2: 1 - DDR3: max (10 ns, 5 tCK) - DDR4: 
                # ax (10 ns, 5 tCK) For configurations with MEMC_FREQ_RATIO=2, program this to recommended value divided by two and round it up
                # to next integer.
                # PSU_DDRC_DRAMTMG5_T_CKSRE                                                       0x6

                # Minimum CKE low width for Self refresh or Self refresh power down entry to exit timing in memory clock cycles. Recommended se
                # tings: - mDDR: tRFC - LPDDR2: tCKESR - LPDDR3: tCKESR - LPDDR4: max(tCKELPD, tSR) - DDR2: tCKE - DDR3: tCKE + 1 - DDR4: tCKE 
                #  1 For configurations with MEMC_FREQ_RATIO=2, program this to recommended value divided by two and round it up to next intege
                # .
                # PSU_DDRC_DRAMTMG5_T_CKESR                                                       0x4

                # Minimum number of cycles of CKE HIGH/LOW during power-down and self refresh. - LPDDR2/LPDDR3 mode: Set this to the larger of 
                # CKE or tCKESR - LPDDR4 mode: Set this to the larger of tCKE, tCKELPD or tSR. - Non-LPDDR2/non-LPDDR3/non-LPDDR4 designs: Set 
                # his to tCKE value. For configurations with MEMC_FREQ_RATIO=2, program this to (value described above)/2 and round it up to th
                #  next integer value. Unit: Clocks.
                # PSU_DDRC_DRAMTMG5_T_CKE                                                         0x3

                # SDRAM Timing Register 5
                #(OFFSET, MASK, VALUE)      (0XFD070114, 0x0F0F3F1FU ,0x06060403U)  */
    mask_write 0XFD070114 0x0F0F3F1F 0x06060403
                # Register : DRAMTMG6 @ 0XFD070118</p>

                # This is the time after Deep Power Down Entry that CK is maintained as a valid clock. Specifies the clock disable delay after 
                # PDE. Recommended settings: - mDDR: 0 - LPDDR2: 2 - LPDDR3: 2 For configurations with MEMC_FREQ_RATIO=2, program this to recom
                # ended value divided by two and round it up to next integer. This is only present for designs supporting mDDR or LPDDR2/LPDDR3
                # devices.
                # PSU_DDRC_DRAMTMG6_T_CKDPDE                                                      0x1

                # This is the time before Deep Power Down Exit that CK is maintained as a valid clock before issuing DPDX. Specifies the clock 
                # table time before DPDX. Recommended settings: - mDDR: 1 - LPDDR2: 2 - LPDDR3: 2 For configurations with MEMC_FREQ_RATIO=2, pr
                # gram this to recommended value divided by two and round it up to next integer. This is only present for designs supporting mD
                # R or LPDDR2 devices.
                # PSU_DDRC_DRAMTMG6_T_CKDPDX                                                      0x1

                # This is the time before Clock Stop Exit that CK is maintained as a valid clock before issuing Clock Stop Exit. Specifies the 
                # lock stable time before next command after Clock Stop Exit. Recommended settings: - mDDR: 1 - LPDDR2: tXP + 2 - LPDDR3: tXP +
                # 2 - LPDDR4: tXP + 2 For configurations with MEMC_FREQ_RATIO=2, program this to recommended value divided by two and round it 
                # p to next integer. This is only present for designs supporting mDDR or LPDDR2/LPDDR3/LPDDR4 devices.
                # PSU_DDRC_DRAMTMG6_T_CKCSX                                                       0x4

                # SDRAM Timing Register 6
                #(OFFSET, MASK, VALUE)      (0XFD070118, 0x0F0F000FU ,0x01010004U)  */
    mask_write 0XFD070118 0x0F0F000F 0x01010004
                # Register : DRAMTMG7 @ 0XFD07011C</p>

                # This is the time after Power Down Entry that CK is maintained as a valid clock. Specifies the clock disable delay after PDE. 
                # ecommended settings: - mDDR: 0 - LPDDR2: 2 - LPDDR3: 2 - LPDDR4: tCKCKEL For configurations with MEMC_FREQ_RATIO=2, program t
                # is to recommended value divided by two and round it up to next integer. This is only present for designs supporting mDDR or L
                # DDR2/LPDDR3/LPDDR4 devices.
                # PSU_DDRC_DRAMTMG7_T_CKPDE                                                       0x1

                # This is the time before Power Down Exit that CK is maintained as a valid clock before issuing PDX. Specifies the clock stable
                # time before PDX. Recommended settings: - mDDR: 0 - LPDDR2: 2 - LPDDR3: 2 - LPDDR4: 2 For configurations with MEMC_FREQ_RATIO=
                # , program this to recommended value divided by two and round it up to next integer. This is only present for designs supporti
                # g mDDR or LPDDR2/LPDDR3/LPDDR4 devices.
                # PSU_DDRC_DRAMTMG7_T_CKPDX                                                       0x1

                # SDRAM Timing Register 7
                #(OFFSET, MASK, VALUE)      (0XFD07011C, 0x00000F0FU ,0x00000101U)  */
    mask_write 0XFD07011C 0x00000F0F 0x00000101
                # Register : DRAMTMG8 @ 0XFD070120</p>

                # tXS_FAST: Exit Self Refresh to ZQCL, ZQCS and MRS (only CL, WR, RTP and Geardown mode). For configurations with MEMC_FREQ_RAT
                # O=2, program this to the above value divided by 2 and round up to next integer value. Unit: Multiples of 32 clocks. Note: Thi
                #  is applicable to only ZQCL/ZQCS commands. Note: Ensure this is less than or equal to t_xs_x32.
                # PSU_DDRC_DRAMTMG8_T_XS_FAST_X32                                                 0x4

                # tXS_ABORT: Exit Self Refresh to commands not requiring a locked DLL in Self Refresh Abort. For configurations with MEMC_FREQ_
                # ATIO=2, program this to the above value divided by 2 and round up to next integer value. Unit: Multiples of 32 clocks. Note: 
                # nsure this is less than or equal to t_xs_x32.
                # PSU_DDRC_DRAMTMG8_T_XS_ABORT_X32                                                0x4

                # tXSDLL: Exit Self Refresh to commands requiring a locked DLL. For configurations with MEMC_FREQ_RATIO=2, program this to the 
                # bove value divided by 2 and round up to next integer value. Unit: Multiples of 32 clocks. Note: Used only for DDR2, DDR3 and 
                # DR4 SDRAMs.
                # PSU_DDRC_DRAMTMG8_T_XS_DLL_X32                                                  0xd

                # tXS: Exit Self Refresh to commands not requiring a locked DLL. For configurations with MEMC_FREQ_RATIO=2, program this to the
                # above value divided by 2 and round up to next integer value. Unit: Multiples of 32 clocks. Note: Used only for DDR2, DDR3 and
                # DDR4 SDRAMs.
                # PSU_DDRC_DRAMTMG8_T_XS_X32                                                      0x6

                # SDRAM Timing Register 8
                #(OFFSET, MASK, VALUE)      (0XFD070120, 0x7F7F7F7FU ,0x04040D06U)  */
    mask_write 0XFD070120 0x7F7F7F7F 0x04040D06
                # Register : DRAMTMG9 @ 0XFD070124</p>

                # DDR4 Write preamble mode - 0: 1tCK preamble - 1: 2tCK preamble Present only with MEMC_FREQ_RATIO=2
                # PSU_DDRC_DRAMTMG9_DDR4_WR_PREAMBLE                                              0x0

                # tCCD_S: This is the minimum time between two reads or two writes for different bank group. For bank switching (from bank 'a' 
                # o bank 'b'), the minimum time is this value + 1. For configurations with MEMC_FREQ_RATIO=2, program this to (tCCD_S/2) and ro
                # nd it up to the next integer value. Present only in designs configured to support DDR4. Unit: clocks.
                # PSU_DDRC_DRAMTMG9_T_CCD_S                                                       0x2

                # tRRD_S: Minimum time between activates from bank 'a' to bank 'b' for different bank group. For configurations with MEMC_FREQ_
                # ATIO=2, program this to (tRRD_S/2) and round it up to the next integer value. Present only in designs configured to support D
                # R4. Unit: Clocks.
                # PSU_DDRC_DRAMTMG9_T_RRD_S                                                       0x2

                # CWL + PL + BL/2 + tWTR_S Minimum time from write command to read command for different bank group. Includes time for bus turn
                # round, recovery times, and all per-bank, per-rank, and global constraints. Present only in designs configured to support DDR4
                #  Unit: Clocks. Where: - CWL = CAS write latency - PL = Parity latency - BL = burst length. This must match the value programm
                # d in the BL bit of the mode register to the SDRAM - tWTR_S = internal write to read command delay for different bank group. T
                # is comes directly from the SDRAM specification. For configurations with MEMC_FREQ_RATIO=2, divide the value calculated using 
                # he above equation by 2, and round it up to next integer.
                # PSU_DDRC_DRAMTMG9_WR2RD_S                                                       0xb

                # SDRAM Timing Register 9
                #(OFFSET, MASK, VALUE)      (0XFD070124, 0x40070F3FU ,0x0002020BU)  */
    mask_write 0XFD070124 0x40070F3F 0x0002020B
                # Register : DRAMTMG11 @ 0XFD07012C</p>

                # tXMPDLL: This is the minimum Exit MPSM to commands requiring a locked DLL. For configurations with MEMC_FREQ_RATIO=2, program
                # this to (tXMPDLL/2) and round it up to the next integer value. Present only in designs configured to support DDR4. Unit: Mult
                # ples of 32 clocks.
                # PSU_DDRC_DRAMTMG11_POST_MPSM_GAP_X32                                            0x6f

                # tMPX_LH: This is the minimum CS_n Low hold time to CKE rising edge. For configurations with MEMC_FREQ_RATIO=2, program this t
                #  RoundUp(tMPX_LH/2)+1. Present only in designs configured to support DDR4. Unit: clocks.
                # PSU_DDRC_DRAMTMG11_T_MPX_LH                                                     0x7

                # tMPX_S: Minimum time CS setup time to CKE. For configurations with MEMC_FREQ_RATIO=2, program this to (tMPX_S/2) and round it
                # up to the next integer value. Present only in designs configured to support DDR4. Unit: Clocks.
                # PSU_DDRC_DRAMTMG11_T_MPX_S                                                      0x1

                # tCKMPE: Minimum valid clock requirement after MPSM entry. Present only in designs configured to support DDR4. Unit: Clocks. F
                # r configurations with MEMC_FREQ_RATIO=2, divide the value calculated using the above equation by 2, and round it up to next i
                # teger.
                # PSU_DDRC_DRAMTMG11_T_CKMPE                                                      0xe

                # SDRAM Timing Register 11
                #(OFFSET, MASK, VALUE)      (0XFD07012C, 0x7F1F031FU ,0x6F07010EU)  */
    mask_write 0XFD07012C 0x7F1F031F 0x6F07010E
                # Register : DRAMTMG12 @ 0XFD070130</p>

                # tCMDCKE: Delay from valid command to CKE input LOW. Set this to the larger of tESCKE or tCMDCKE For configurations with MEMC_
                # REQ_RATIO=2, program this to (max(tESCKE, tCMDCKE)/2) and round it up to next integer value.
                # PSU_DDRC_DRAMTMG12_T_CMDCKE                                                     0x2

                # tCKEHCMD: Valid command requirement after CKE input HIGH. For configurations with MEMC_FREQ_RATIO=2, program this to (tCKEHCM
                # /2) and round it up to next integer value.
                # PSU_DDRC_DRAMTMG12_T_CKEHCMD                                                    0x6

                # tMRD_PDA: This is the Mode Register Set command cycle time in PDA mode. For configurations with MEMC_FREQ_RATIO=2, program th
                # s to (tMRD_PDA/2) and round it up to next integer value.
                # PSU_DDRC_DRAMTMG12_T_MRD_PDA                                                    0x8

                # SDRAM Timing Register 12
                #(OFFSET, MASK, VALUE)      (0XFD070130, 0x00030F1FU ,0x00020608U)  */
    mask_write 0XFD070130 0x00030F1F 0x00020608
                # Register : ZQCTL0 @ 0XFD070180</p>

                # - 1 - Disable uMCTL2 generation of ZQCS/MPC(ZQ calibration) command. Register DBGCMD.zq_calib_short can be used instead to is
                # ue ZQ calibration request from APB module. - 0 - Internally generate ZQCS/MPC(ZQ calibration) commands based on ZQCTL1.t_zq_s
                # ort_interval_x1024. This is only present for designs supporting DDR3/DDR4 or LPDDR2/LPDDR3/LPDDR4 devices.
                # PSU_DDRC_ZQCTL0_DIS_AUTO_ZQ                                                     0x1

                # - 1 - Disable issuing of ZQCL/MPC(ZQ calibration) command at Self-Refresh/SR-Powerdown exit. Only applicable when run in DDR3
                # or DDR4 or LPDDR2 or LPDDR3 or LPDDR4 mode. - 0 - Enable issuing of ZQCL/MPC(ZQ calibration) command at Self-Refresh/SR-Power
                # own exit. Only applicable when run in DDR3 or DDR4 or LPDDR2 or LPDDR3 or LPDDR4 mode. This is only present for designs suppo
                # ting DDR3/DDR4 or LPDDR2/LPDDR3/LPDDR4 devices.
                # PSU_DDRC_ZQCTL0_DIS_SRX_ZQCL                                                    0x0

                # - 1 - Denotes that ZQ resistor is shared between ranks. Means ZQinit/ZQCL/ZQCS/MPC(ZQ calibration) commands are sent to one r
                # nk at a time with tZQinit/tZQCL/tZQCS/tZQCAL/tZQLAT timing met between commands so that commands to different ranks do not ov
                # rlap. - 0 - ZQ resistor is not shared. This is only present for designs supporting DDR3/DDR4 or LPDDR2/LPDDR3/LPDDR4 devices.
                # PSU_DDRC_ZQCTL0_ZQ_RESISTOR_SHARED                                              0x0

                # - 1 - Disable issuing of ZQCL command at Maximum Power Saving Mode exit. Only applicable when run in DDR4 mode. - 0 - Enable 
                # ssuing of ZQCL command at Maximum Power Saving Mode exit. Only applicable when run in DDR4 mode. This is only present for des
                # gns supporting DDR4 devices.
                # PSU_DDRC_ZQCTL0_DIS_MPSMX_ZQCL                                                  0x0

                # tZQoper for DDR3/DDR4, tZQCL for LPDDR2/LPDDR3, tZQCAL for LPDDR4: Number of cycles of NOP required after a ZQCL (ZQ calibrat
                # on long)/MPC(ZQ Start) command is issued to SDRAM. For configurations with MEMC_FREQ_RATIO=2: DDR3/DDR4: program this to tZQo
                # er/2 and round it up to the next integer value. LPDDR2/LPDDR3: program this to tZQCL/2 and round it up to the next integer va
                # ue. LPDDR4: program this to tZQCAL/2 and round it up to the next integer value. Unit: Clock cycles. This is only present for 
                # esigns supporting DDR3/DDR4 or LPDDR2/LPDDR3/LPDDR4 devices.
                # PSU_DDRC_ZQCTL0_T_ZQ_LONG_NOP                                                   0x100

                # tZQCS for DDR3/DD4/LPDDR2/LPDDR3, tZQLAT for LPDDR4: Number of cycles of NOP required after a ZQCS (ZQ calibration short)/MPC
                # ZQ Latch) command is issued to SDRAM. For configurations with MEMC_FREQ_RATIO=2, program this to tZQCS/2 and round it up to t
                # e next integer value. Unit: Clock cycles. This is only present for designs supporting DDR3/DDR4 or LPDDR2/LPDDR3/LPDDR4 devic
                # s.
                # PSU_DDRC_ZQCTL0_T_ZQ_SHORT_NOP                                                  0x40

                # ZQ Control Register 0
                #(OFFSET, MASK, VALUE)      (0XFD070180, 0xF7FF03FFU ,0x81000040U)  */
    mask_write 0XFD070180 0xF7FF03FF 0x81000040
                # Register : ZQCTL1 @ 0XFD070184</p>

                # tZQReset: Number of cycles of NOP required after a ZQReset (ZQ calibration Reset) command is issued to SDRAM. For configurati
                # ns with MEMC_FREQ_RATIO=2, program this to tZQReset/2 and round it up to the next integer value. Unit: Clock cycles. This is 
                # nly present for designs supporting LPDDR2/LPDDR3/LPDDR4 devices.
                # PSU_DDRC_ZQCTL1_T_ZQ_RESET_NOP                                                  0x20

                # Average interval to wait between automatically issuing ZQCS (ZQ calibration short)/MPC(ZQ calibration) commands to DDR3/DDR4/
                # PDDR2/LPDDR3/LPDDR4 devices. Meaningless, if ZQCTL0.dis_auto_zq=1. Unit: 1024 clock cycles. This is only present for designs 
                # upporting DDR3/DDR4 or LPDDR2/LPDDR3/LPDDR4 devices.
                # PSU_DDRC_ZQCTL1_T_ZQ_SHORT_INTERVAL_X1024                                       0x19707

                # ZQ Control Register 1
                #(OFFSET, MASK, VALUE)      (0XFD070184, 0x3FFFFFFFU ,0x02019707U)  */
    mask_write 0XFD070184 0x3FFFFFFF 0x02019707
                # Register : DFITMG0 @ 0XFD070190</p>

                # Specifies the number of DFI clock cycles after an assertion or de-assertion of the DFI control signals that the control signa
                # s at the PHY-DRAM interface reflect the assertion or de-assertion. If the DFI clock and the memory clock are not phase-aligne
                # , this timing parameter should be rounded up to the next integer value. Note that if using RDIMM, it is necessary to incremen
                #  this parameter by RDIMM's extra cycle of latency in terms of DFI clock.
                # PSU_DDRC_DFITMG0_DFI_T_CTRL_DELAY                                               0x4

                # Defines whether dfi_rddata_en/dfi_rddata/dfi_rddata_valid is generated using HDR or SDR values Selects whether value in DFITM
                # 0.dfi_t_rddata_en is in terms of SDR or HDR clock cycles: - 0 in terms of HDR clock cycles - 1 in terms of SDR clock cycles R
                # fer to PHY specification for correct value.
                # PSU_DDRC_DFITMG0_DFI_RDDATA_USE_SDR                                             0x1

                # Time from the assertion of a read command on the DFI interface to the assertion of the dfi_rddata_en signal. Refer to PHY spe
                # ification for correct value. This corresponds to the DFI parameter trddata_en. Note that, depending on the PHY, if using RDIM
                # , it may be necessary to use the value (CL + 1) in the calculation of trddata_en. This is to compensate for the extra cycle o
                #  latency through the RDIMM. Unit: Clocks
                # PSU_DDRC_DFITMG0_DFI_T_RDDATA_EN                                                0xb

                # Defines whether dfi_wrdata_en/dfi_wrdata/dfi_wrdata_mask is generated using HDR or SDR values Selects whether value in DFITMG
                # .dfi_tphy_wrlat is in terms of SDR or HDR clock cycles Selects whether value in DFITMG0.dfi_tphy_wrdata is in terms of SDR or
                # HDR clock cycles - 0 in terms of HDR clock cycles - 1 in terms of SDR clock cycles Refer to PHY specification for correct val
                # e.
                # PSU_DDRC_DFITMG0_DFI_WRDATA_USE_SDR                                             0x1

                # Specifies the number of clock cycles between when dfi_wrdata_en is asserted to when the associated write data is driven on th
                #  dfi_wrdata signal. This corresponds to the DFI timing parameter tphy_wrdata. Refer to PHY specification for correct value. N
                # te, max supported value is 8. Unit: Clocks
                # PSU_DDRC_DFITMG0_DFI_TPHY_WRDATA                                                0x2

                # Write latency Number of clocks from the write command to write data enable (dfi_wrdata_en). This corresponds to the DFI timin
                #  parameter tphy_wrlat. Refer to PHY specification for correct value.Note that, depending on the PHY, if using RDIMM, it may b
                #  necessary to use the value (CL + 1) in the calculation of tphy_wrlat. This is to compensate for the extra cycle of latency t
                # rough the RDIMM.
                # PSU_DDRC_DFITMG0_DFI_TPHY_WRLAT                                                 0xb

                # DFI Timing Register 0
                #(OFFSET, MASK, VALUE)      (0XFD070190, 0x1FBFBF3FU ,0x048B820BU)  */
    mask_write 0XFD070190 0x1FBFBF3F 0x048B820B
                # Register : DFITMG1 @ 0XFD070194</p>

                # Specifies the number of DFI PHY clocks between when the dfi_cs signal is asserted and when the associated command is driven. 
                # his field is used for CAL mode, should be set to '0' or the value which matches the CAL mode register setting in the DRAM. If
                # the PHY can add the latency for CAL mode, this should be set to '0'. Valid Range: 0, 3, 4, 5, 6, and 8
                # PSU_DDRC_DFITMG1_DFI_T_CMD_LAT                                                  0x0

                # Specifies the number of DFI PHY clocks between when the dfi_cs signal is asserted and when the associated dfi_parity_in signa
                #  is driven.
                # PSU_DDRC_DFITMG1_DFI_T_PARIN_LAT                                                0x0

                # Specifies the number of DFI clocks between when the dfi_wrdata_en signal is asserted and when the corresponding write data tr
                # nsfer is completed on the DRAM bus. This corresponds to the DFI timing parameter twrdata_delay. Refer to PHY specification fo
                #  correct value. For DFI 3.0 PHY, set to twrdata_delay, a new timing parameter introduced in DFI 3.0. For DFI 2.1 PHY, set to 
                # phy_wrdata + (delay of DFI write data to the DRAM). Value to be programmed is in terms of DFI clocks, not PHY clocks. In FREQ
                # RATIO=2, divide PHY's value by 2 and round up to next integer. If using DFITMG0.dfi_wrdata_use_sdr=1, add 1 to the value. Uni
                # : Clocks
                # PSU_DDRC_DFITMG1_DFI_T_WRDATA_DELAY                                             0x3

                # Specifies the number of DFI clock cycles from the assertion of the dfi_dram_clk_disable signal on the DFI until the clock to 
                # he DRAM memory devices, at the PHY-DRAM boundary, maintains a low value. If the DFI clock and the memory clock are not phase 
                # ligned, this timing parameter should be rounded up to the next integer value.
                # PSU_DDRC_DFITMG1_DFI_T_DRAM_CLK_DISABLE                                         0x3

                # Specifies the number of DFI clock cycles from the de-assertion of the dfi_dram_clk_disable signal on the DFI until the first 
                # alid rising edge of the clock to the DRAM memory devices, at the PHY-DRAM boundary. If the DFI clock and the memory clock are
                # not phase aligned, this timing parameter should be rounded up to the next integer value.
                # PSU_DDRC_DFITMG1_DFI_T_DRAM_CLK_ENABLE                                          0x4

                # DFI Timing Register 1
                #(OFFSET, MASK, VALUE)      (0XFD070194, 0xF31F0F0FU ,0x00030304U)  */
    mask_write 0XFD070194 0xF31F0F0F 0x00030304
                # Register : DFILPCFG0 @ 0XFD070198</p>

                # Setting for DFI's tlp_resp time. Same value is used for both Power Down, Self Refresh, Deep Power Down and Maximum Power Savi
                # g modes. DFI 2.1 specification onwards, recommends using a fixed value of 7 always.
                # PSU_DDRC_DFILPCFG0_DFI_TLP_RESP                                                 0x7

                # Value to drive on dfi_lp_wakeup signal when Deep Power Down mode is entered. Determines the DFI's tlp_wakeup time: - 0x0 - 16
                # cycles - 0x1 - 32 cycles - 0x2 - 64 cycles - 0x3 - 128 cycles - 0x4 - 256 cycles - 0x5 - 512 cycles - 0x6 - 1024 cycles - 0x7
                # - 2048 cycles - 0x8 - 4096 cycles - 0x9 - 8192 cycles - 0xA - 16384 cycles - 0xB - 32768 cycles - 0xC - 65536 cycles - 0xD - 
                # 31072 cycles - 0xE - 262144 cycles - 0xF - Unlimited This is only present for designs supporting mDDR or LPDDR2/LPDDR3 device
                # .
                # PSU_DDRC_DFILPCFG0_DFI_LP_WAKEUP_DPD                                            0x0

                # Enables DFI Low Power interface handshaking during Deep Power Down Entry/Exit. - 0 - Disabled - 1 - Enabled This is only pres
                # nt for designs supporting mDDR or LPDDR2/LPDDR3 devices.
                # PSU_DDRC_DFILPCFG0_DFI_LP_EN_DPD                                                0x0

                # Value to drive on dfi_lp_wakeup signal when Self Refresh mode is entered. Determines the DFI's tlp_wakeup time: - 0x0 - 16 cy
                # les - 0x1 - 32 cycles - 0x2 - 64 cycles - 0x3 - 128 cycles - 0x4 - 256 cycles - 0x5 - 512 cycles - 0x6 - 1024 cycles - 0x7 - 
                # 048 cycles - 0x8 - 4096 cycles - 0x9 - 8192 cycles - 0xA - 16384 cycles - 0xB - 32768 cycles - 0xC - 65536 cycles - 0xD - 131
                # 72 cycles - 0xE - 262144 cycles - 0xF - Unlimited
                # PSU_DDRC_DFILPCFG0_DFI_LP_WAKEUP_SR                                             0x0

                # Enables DFI Low Power interface handshaking during Self Refresh Entry/Exit. - 0 - Disabled - 1 - Enabled
                # PSU_DDRC_DFILPCFG0_DFI_LP_EN_SR                                                 0x1

                # Value to drive on dfi_lp_wakeup signal when Power Down mode is entered. Determines the DFI's tlp_wakeup time: - 0x0 - 16 cycl
                # s - 0x1 - 32 cycles - 0x2 - 64 cycles - 0x3 - 128 cycles - 0x4 - 256 cycles - 0x5 - 512 cycles - 0x6 - 1024 cycles - 0x7 - 20
                # 8 cycles - 0x8 - 4096 cycles - 0x9 - 8192 cycles - 0xA - 16384 cycles - 0xB - 32768 cycles - 0xC - 65536 cycles - 0xD - 13107
                #  cycles - 0xE - 262144 cycles - 0xF - Unlimited
                # PSU_DDRC_DFILPCFG0_DFI_LP_WAKEUP_PD                                             0x4

                # Enables DFI Low Power interface handshaking during Power Down Entry/Exit. - 0 - Disabled - 1 - Enabled
                # PSU_DDRC_DFILPCFG0_DFI_LP_EN_PD                                                 0x1

                # DFI Low Power Configuration Register 0
                #(OFFSET, MASK, VALUE)      (0XFD070198, 0x0FF1F1F1U ,0x07000141U)  */
    mask_write 0XFD070198 0x0FF1F1F1 0x07000141
                # Register : DFILPCFG1 @ 0XFD07019C</p>

                # Value to drive on dfi_lp_wakeup signal when Maximum Power Saving Mode is entered. Determines the DFI's tlp_wakeup time: - 0x0
                # - 16 cycles - 0x1 - 32 cycles - 0x2 - 64 cycles - 0x3 - 128 cycles - 0x4 - 256 cycles - 0x5 - 512 cycles - 0x6 - 1024 cycles 
                #  0x7 - 2048 cycles - 0x8 - 4096 cycles - 0x9 - 8192 cycles - 0xA - 16384 cycles - 0xB - 32768 cycles - 0xC - 65536 cycles - 0
                # D - 131072 cycles - 0xE - 262144 cycles - 0xF - Unlimited This is only present for designs supporting DDR4 devices.
                # PSU_DDRC_DFILPCFG1_DFI_LP_WAKEUP_MPSM                                           0x2

                # Enables DFI Low Power interface handshaking during Maximum Power Saving Mode Entry/Exit. - 0 - Disabled - 1 - Enabled This is
                # only present for designs supporting DDR4 devices.
                # PSU_DDRC_DFILPCFG1_DFI_LP_EN_MPSM                                               0x1

                # DFI Low Power Configuration Register 1
                #(OFFSET, MASK, VALUE)      (0XFD07019C, 0x000000F1U ,0x00000021U)  */
    mask_write 0XFD07019C 0x000000F1 0x00000021
                # Register : DFIUPD1 @ 0XFD0701A4</p>

                # This is the minimum amount of time between uMCTL2 initiated DFI update requests (which is executed whenever the uMCTL2 is idl
                # ). Set this number higher to reduce the frequency of update requests, which can have a small impact on the latency of the fir
                # t read request when the uMCTL2 is idle. Unit: 1024 clocks
                # PSU_DDRC_DFIUPD1_DFI_T_CTRLUPD_INTERVAL_MIN_X1024                               0x41

                # This is the maximum amount of time between uMCTL2 initiated DFI update requests. This timer resets with each update request; 
                # hen the timer expires dfi_ctrlupd_req is sent and traffic is blocked until the dfi_ctrlupd_ackx is received. PHY can use this
                # idle time to recalibrate the delay lines to the DLLs. The DFI controller update is also used to reset PHY FIFO pointers in ca
                # e of data capture errors. Updates are required to maintain calibration over PVT, but frequent updates may impact performance.
                # Note: Value programmed for DFIUPD1.dfi_t_ctrlupd_interval_max_x1024 must be greater than DFIUPD1.dfi_t_ctrlupd_interval_min_x
                # 024. Unit: 1024 clocks
                # PSU_DDRC_DFIUPD1_DFI_T_CTRLUPD_INTERVAL_MAX_X1024                               0xe2

                # DFI Update Register 1
                #(OFFSET, MASK, VALUE)      (0XFD0701A4, 0x00FF00FFU ,0x004100E2U)  */
    mask_write 0XFD0701A4 0x00FF00FF 0x004100E2
                # Register : DFIMISC @ 0XFD0701B0</p>

                # Defines polarity of dfi_wrdata_cs and dfi_rddata_cs signals. - 0: Signals are active low - 1: Signals are active high
                # PSU_DDRC_DFIMISC_DFI_DATA_CS_POLARITY                                           0x0

                # DBI implemented in DDRC or PHY. - 0 - DDRC implements DBI functionality. - 1 - PHY implements DBI functionality. Present only
                # in designs configured to support DDR4 and LPDDR4.
                # PSU_DDRC_DFIMISC_PHY_DBI_MODE                                                   0x0

                # PHY initialization complete enable signal. When asserted the dfi_init_complete signal can be used to trigger SDRAM initialisa
                # ion
                # PSU_DDRC_DFIMISC_DFI_INIT_COMPLETE_EN                                           0x0

                # DFI Miscellaneous Control Register
                #(OFFSET, MASK, VALUE)      (0XFD0701B0, 0x00000007U ,0x00000000U)  */
    mask_write 0XFD0701B0 0x00000007 0x00000000
                # Register : DFITMG2 @ 0XFD0701B4</p>

                # >Number of clocks between when a read command is sent on the DFI control interface and when the associated dfi_rddata_cs sign
                # l is asserted. This corresponds to the DFI timing parameter tphy_rdcslat. Refer to PHY specification for correct value.
                # PSU_DDRC_DFITMG2_DFI_TPHY_RDCSLAT                                               0x9

                # Number of clocks between when a write command is sent on the DFI control interface and when the associated dfi_wrdata_cs sign
                # l is asserted. This corresponds to the DFI timing parameter tphy_wrcslat. Refer to PHY specification for correct value.
                # PSU_DDRC_DFITMG2_DFI_TPHY_WRCSLAT                                               0x6

                # DFI Timing Register 2
                #(OFFSET, MASK, VALUE)      (0XFD0701B4, 0x00003F3FU ,0x00000906U)  */
    mask_write 0XFD0701B4 0x00003F3F 0x00000906
                # Register : DBICTL @ 0XFD0701C0</p>

                # Read DBI enable signal in DDRC. - 0 - Read DBI is disabled. - 1 - Read DBI is enabled. This signal must be set the same value
                # as DRAM's mode register. - DDR4: MR5 bit A12. When x4 devices are used, this signal must be set to 0. - LPDDR4: MR3[6]
                # PSU_DDRC_DBICTL_RD_DBI_EN                                                       0x0

                # Write DBI enable signal in DDRC. - 0 - Write DBI is disabled. - 1 - Write DBI is enabled. This signal must be set the same va
                # ue as DRAM's mode register. - DDR4: MR5 bit A11. When x4 devices are used, this signal must be set to 0. - LPDDR4: MR3[7]
                # PSU_DDRC_DBICTL_WR_DBI_EN                                                       0x0

                # DM enable signal in DDRC. - 0 - DM is disabled. - 1 - DM is enabled. This signal must be set the same logical value as DRAM's
                # mode register. - DDR4: Set this to same value as MR5 bit A10. When x4 devices are used, this signal must be set to 0. - LPDDR
                # : Set this to inverted value of MR13[5] which is opposite polarity from this signal
                # PSU_DDRC_DBICTL_DM_EN                                                           0x1

                # DM/DBI Control Register
                #(OFFSET, MASK, VALUE)      (0XFD0701C0, 0x00000007U ,0x00000001U)  */
    mask_write 0XFD0701C0 0x00000007 0x00000001
                # Register : ADDRMAP0 @ 0XFD070200</p>

                # Selects the HIF address bit used as rank address bit 0. Valid Range: 0 to 27, and 31 Internal Base: 6 The selected HIF addres
                #  bit is determined by adding the internal base to the value of this field. If set to 31, rank address bit 0 is set to 0.
                # PSU_DDRC_ADDRMAP0_ADDRMAP_CS_BIT0                                               0x1f

                # Address Map Register 0
                #(OFFSET, MASK, VALUE)      (0XFD070200, 0x0000001FU ,0x0000001FU)  */
    mask_write 0XFD070200 0x0000001F 0x0000001F
                # Register : ADDRMAP1 @ 0XFD070204</p>

                # Selects the HIF address bit used as bank address bit 2. Valid Range: 0 to 29 and 31 Internal Base: 4 The selected HIF address
                # bit is determined by adding the internal base to the value of this field. If set to 31, bank address bit 2 is set to 0.
                # PSU_DDRC_ADDRMAP1_ADDRMAP_BANK_B2                                               0x1f

                # Selects the HIF address bits used as bank address bit 1. Valid Range: 0 to 30 Internal Base: 3 The selected HIF address bit f
                # r each of the bank address bits is determined by adding the internal base to the value of this field.
                # PSU_DDRC_ADDRMAP1_ADDRMAP_BANK_B1                                               0xa

                # Selects the HIF address bits used as bank address bit 0. Valid Range: 0 to 30 Internal Base: 2 The selected HIF address bit f
                # r each of the bank address bits is determined by adding the internal base to the value of this field.
                # PSU_DDRC_ADDRMAP1_ADDRMAP_BANK_B0                                               0xa

                # Address Map Register 1
                #(OFFSET, MASK, VALUE)      (0XFD070204, 0x001F1F1FU ,0x001F0A0AU)  */
    mask_write 0XFD070204 0x001F1F1F 0x001F0A0A
                # Register : ADDRMAP2 @ 0XFD070208</p>

                # - Full bus width mode: Selects the HIF address bit used as column address bit 5. - Half bus width mode: Selects the HIF addre
                # s bit used as column address bit 6. - Quarter bus width mode: Selects the HIF address bit used as column address bit 7 . Vali
                #  Range: 0 to 7, and 15 Internal Base: 5 The selected HIF address bit is determined by adding the internal base to the value o
                #  this field. If set to 15, this column address bit is set to 0.
                # PSU_DDRC_ADDRMAP2_ADDRMAP_COL_B5                                                0x0

                # - Full bus width mode: Selects the HIF address bit used as column address bit 4. - Half bus width mode: Selects the HIF addre
                # s bit used as column address bit 5. - Quarter bus width mode: Selects the HIF address bit used as column address bit 6. Valid
                # Range: 0 to 7, and 15 Internal Base: 4 The selected HIF address bit is determined by adding the internal base to the value of
                # this field. If set to 15, this column address bit is set to 0.
                # PSU_DDRC_ADDRMAP2_ADDRMAP_COL_B4                                                0x0

                # - Full bus width mode: Selects the HIF address bit used as column address bit 3. - Half bus width mode: Selects the HIF addre
                # s bit used as column address bit 4. - Quarter bus width mode: Selects the HIF address bit used as column address bit 5. Valid
                # Range: 0 to 7 Internal Base: 3 The selected HIF address bit is determined by adding the internal base to the value of this fi
                # ld. Note, if UMCTL2_INCL_ARB=1 and MEMC_BURST_LENGTH=16, it is required to program this to 0, hence register does not exist i
                #  this case.
                # PSU_DDRC_ADDRMAP2_ADDRMAP_COL_B3                                                0x0

                # - Full bus width mode: Selects the HIF address bit used as column address bit 2. - Half bus width mode: Selects the HIF addre
                # s bit used as column address bit 3. - Quarter bus width mode: Selects the HIF address bit used as column address bit 4. Valid
                # Range: 0 to 7 Internal Base: 2 The selected HIF address bit is determined by adding the internal base to the value of this fi
                # ld. Note, if UMCTL2_INCL_ARB=1 and MEMC_BURST_LENGTH=8 or 16, it is required to program this to 0.
                # PSU_DDRC_ADDRMAP2_ADDRMAP_COL_B2                                                0x0

                # Address Map Register 2
                #(OFFSET, MASK, VALUE)      (0XFD070208, 0x0F0F0F0FU ,0x00000000U)  */
    mask_write 0XFD070208 0x0F0F0F0F 0x00000000
                # Register : ADDRMAP3 @ 0XFD07020C</p>

                # - Full bus width mode: Selects the HIF address bit used as column address bit 9. - Half bus width mode: Selects the HIF addre
                # s bit used as column address bit 11 (10 in LPDDR2/LPDDR3 mode). - Quarter bus width mode: Selects the HIF address bit used as
                # column address bit 13 (11 in LPDDR2/LPDDR3 mode). Valid Range: 0 to 7, and 15 Internal Base: 9 The selected HIF address bit i
                #  determined by adding the internal base to the value of this field. If set to 15, this column address bit is set to 0. Note: 
                # er JEDEC DDR2/3/mDDR specification, column address bit 10 is reserved for indicating auto-precharge, and hence no source addr
                # ss bit can be mapped to column address bit 10. In LPDDR2/LPDDR3, there is a dedicated bit for auto-precharge in the CA bus an
                #  hence column bit 10 is used.
                # PSU_DDRC_ADDRMAP3_ADDRMAP_COL_B9                                                0x0

                # - Full bus width mode: Selects the HIF address bit used as column address bit 8. - Half bus width mode: Selects the HIF addre
                # s bit used as column address bit 9. - Quarter bus width mode: Selects the HIF address bit used as column address bit 11 (10 i
                #  LPDDR2/LPDDR3 mode). Valid Range: 0 to 7, and 15 Internal Base: 8 The selected HIF address bit is determined by adding the i
                # ternal base to the value of this field. If set to 15, this column address bit is set to 0. Note: Per JEDEC DDR2/3/mDDR specif
                # cation, column address bit 10 is reserved for indicating auto-precharge, and hence no source address bit can be mapped to col
                # mn address bit 10. In LPDDR2/LPDDR3, there is a dedicated bit for auto-precharge in the CA bus and hence column bit 10 is use
                # .
                # PSU_DDRC_ADDRMAP3_ADDRMAP_COL_B8                                                0x0

                # - Full bus width mode: Selects the HIF address bit used as column address bit 7. - Half bus width mode: Selects the HIF addre
                # s bit used as column address bit 8. - Quarter bus width mode: Selects the HIF address bit used as column address bit 9. Valid
                # Range: 0 to 7, and 15 Internal Base: 7 The selected HIF address bit is determined by adding the internal base to the value of
                # this field. If set to 15, this column address bit is set to 0.
                # PSU_DDRC_ADDRMAP3_ADDRMAP_COL_B7                                                0x0

                # - Full bus width mode: Selects the HIF address bit used as column address bit 6. - Half bus width mode: Selects the HIF addre
                # s bit used as column address bit 7. - Quarter bus width mode: Selects the HIF address bit used as column address bit 8. Valid
                # Range: 0 to 7, and 15 Internal Base: 6 The selected HIF address bit is determined by adding the internal base to the value of
                # this field. If set to 15, this column address bit is set to 0.
                # PSU_DDRC_ADDRMAP3_ADDRMAP_COL_B6                                                0x0

                # Address Map Register 3
                #(OFFSET, MASK, VALUE)      (0XFD07020C, 0x0F0F0F0FU ,0x00000000U)  */
    mask_write 0XFD07020C 0x0F0F0F0F 0x00000000
                # Register : ADDRMAP4 @ 0XFD070210</p>

                # - Full bus width mode: Selects the HIF address bit used as column address bit 13 (11 in LPDDR2/LPDDR3 mode). - Half bus width
                # mode: Unused. To make it unused, this should be tied to 4'hF. - Quarter bus width mode: Unused. To make it unused, this must 
                # e tied to 4'hF. Valid Range: 0 to 7, and 15 Internal Base: 11 The selected HIF address bit is determined by adding the intern
                # l base to the value of this field. If set to 15, this column address bit is set to 0. Note: Per JEDEC DDR2/3/mDDR specificati
                # n, column address bit 10 is reserved for indicating auto-precharge, and hence no source address bit can be mapped to column a
                # dress bit 10. In LPDDR2/LPDDR3, there is a dedicated bit for auto-precharge in the CA bus and hence column bit 10 is used.
                # PSU_DDRC_ADDRMAP4_ADDRMAP_COL_B11                                               0xf

                # - Full bus width mode: Selects the HIF address bit used as column address bit 11 (10 in LPDDR2/LPDDR3 mode). - Half bus width
                # mode: Selects the HIF address bit used as column address bit 13 (11 in LPDDR2/LPDDR3 mode). - Quarter bus width mode: UNUSED.
                # To make it unused, this must be tied to 4'hF. Valid Range: 0 to 7, and 15 Internal Base: 10 The selected HIF address bit is d
                # termined by adding the internal base to the value of this field. If set to 15, this column address bit is set to 0. Note: Per
                # JEDEC DDR2/3/mDDR specification, column address bit 10 is reserved for indicating auto-precharge, and hence no source address
                # bit can be mapped to column address bit 10. In LPDDR2/LPDDR3, there is a dedicated bit for auto-precharge in the CA bus and h
                # nce column bit 10 is used.
                # PSU_DDRC_ADDRMAP4_ADDRMAP_COL_B10                                               0xf

                # Address Map Register 4
                #(OFFSET, MASK, VALUE)      (0XFD070210, 0x00000F0FU ,0x00000F0FU)  */
    mask_write 0XFD070210 0x00000F0F 0x00000F0F
                # Register : ADDRMAP5 @ 0XFD070214</p>

                # Selects the HIF address bit used as row address bit 11. Valid Range: 0 to 11, and 15 Internal Base: 17 The selected HIF addre
                # s bit is determined by adding the internal base to the value of this field. If set to 15, row address bit 11 is set to 0.
                # PSU_DDRC_ADDRMAP5_ADDRMAP_ROW_B11                                               0x8

                # Selects the HIF address bits used as row address bits 2 to 10. Valid Range: 0 to 11, and 15 Internal Base: 8 (for row address
                # bit 2), 9 (for row address bit 3), 10 (for row address bit 4) etc increasing to 16 (for row address bit 10) The selected HIF 
                # ddress bit for each of the row address bits is determined by adding the internal base to the value of this field. When value 
                # 5 is used the values of row address bits 2 to 10 are defined by registers ADDRMAP9, ADDRMAP10, ADDRMAP11.
                # PSU_DDRC_ADDRMAP5_ADDRMAP_ROW_B2_10                                             0xf

                # Selects the HIF address bits used as row address bit 1. Valid Range: 0 to 11 Internal Base: 7 The selected HIF address bit fo
                #  each of the row address bits is determined by adding the internal base to the value of this field.
                # PSU_DDRC_ADDRMAP5_ADDRMAP_ROW_B1                                                0x8

                # Selects the HIF address bits used as row address bit 0. Valid Range: 0 to 11 Internal Base: 6 The selected HIF address bit fo
                #  each of the row address bits is determined by adding the internal base to the value of this field.
                # PSU_DDRC_ADDRMAP5_ADDRMAP_ROW_B0                                                0x8

                # Address Map Register 5
                #(OFFSET, MASK, VALUE)      (0XFD070214, 0x0F0F0F0FU ,0x080F0808U)  */
    mask_write 0XFD070214 0x0F0F0F0F 0x080F0808
                # Register : ADDRMAP6 @ 0XFD070218</p>

                # Set this to 1 if there is an LPDDR3 SDRAM 6Gb or 12Gb device in use. - 1 - LPDDR3 SDRAM 6Gb/12Gb device in use. Every address
                # having row[14:13]==2'b11 is considered as invalid - 0 - non-LPDDR3 6Gb/12Gb device in use. All addresses are valid Present on
                # y in designs configured to support LPDDR3.
                # PSU_DDRC_ADDRMAP6_LPDDR3_6GB_12GB                                               0x0

                # Selects the HIF address bit used as row address bit 15. Valid Range: 0 to 11, and 15 Internal Base: 21 The selected HIF addre
                # s bit is determined by adding the internal base to the value of this field. If set to 15, row address bit 15 is set to 0.
                # PSU_DDRC_ADDRMAP6_ADDRMAP_ROW_B15                                               0xf

                # Selects the HIF address bit used as row address bit 14. Valid Range: 0 to 11, and 15 Internal Base: 20 The selected HIF addre
                # s bit is determined by adding the internal base to the value of this field. If set to 15, row address bit 14 is set to 0.
                # PSU_DDRC_ADDRMAP6_ADDRMAP_ROW_B14                                               0x8

                # Selects the HIF address bit used as row address bit 13. Valid Range: 0 to 11, and 15 Internal Base: 19 The selected HIF addre
                # s bit is determined by adding the internal base to the value of this field. If set to 15, row address bit 13 is set to 0.
                # PSU_DDRC_ADDRMAP6_ADDRMAP_ROW_B13                                               0x8

                # Selects the HIF address bit used as row address bit 12. Valid Range: 0 to 11, and 15 Internal Base: 18 The selected HIF addre
                # s bit is determined by adding the internal base to the value of this field. If set to 15, row address bit 12 is set to 0.
                # PSU_DDRC_ADDRMAP6_ADDRMAP_ROW_B12                                               0x8

                # Address Map Register 6
                #(OFFSET, MASK, VALUE)      (0XFD070218, 0x8F0F0F0FU ,0x0F080808U)  */
    mask_write 0XFD070218 0x8F0F0F0F 0x0F080808
                # Register : ADDRMAP7 @ 0XFD07021C</p>

                # Selects the HIF address bit used as row address bit 17. Valid Range: 0 to 10, and 15 Internal Base: 23 The selected HIF addre
                # s bit is determined by adding the internal base to the value of this field. If set to 15, row address bit 17 is set to 0.
                # PSU_DDRC_ADDRMAP7_ADDRMAP_ROW_B17                                               0xf

                # Selects the HIF address bit used as row address bit 16. Valid Range: 0 to 11, and 15 Internal Base: 22 The selected HIF addre
                # s bit is determined by adding the internal base to the value of this field. If set to 15, row address bit 16 is set to 0.
                # PSU_DDRC_ADDRMAP7_ADDRMAP_ROW_B16                                               0xf

                # Address Map Register 7
                #(OFFSET, MASK, VALUE)      (0XFD07021C, 0x00000F0FU ,0x00000F0FU)  */
    mask_write 0XFD07021C 0x00000F0F 0x00000F0F
                # Register : ADDRMAP8 @ 0XFD070220</p>

                # Selects the HIF address bits used as bank group address bit 1. Valid Range: 0 to 30, and 31 Internal Base: 3 The selected HIF
                # address bit for each of the bank group address bits is determined by adding the internal base to the value of this field. If 
                # et to 31, bank group address bit 1 is set to 0.
                # PSU_DDRC_ADDRMAP8_ADDRMAP_BG_B1                                                 0x8

                # Selects the HIF address bits used as bank group address bit 0. Valid Range: 0 to 30 Internal Base: 2 The selected HIF address
                # bit for each of the bank group address bits is determined by adding the internal base to the value of this field.
                # PSU_DDRC_ADDRMAP8_ADDRMAP_BG_B0                                                 0x8

                # Address Map Register 8
                #(OFFSET, MASK, VALUE)      (0XFD070220, 0x00001F1FU ,0x00000808U)  */
    mask_write 0XFD070220 0x00001F1F 0x00000808
                # Register : ADDRMAP9 @ 0XFD070224</p>

                # Selects the HIF address bits used as row address bit 5. Valid Range: 0 to 11 Internal Base: 11 The selected HIF address bit f
                # r each of the row address bits is determined by adding the internal base to the value of this field. This register field is u
                # ed only when ADDRMAP5.addrmap_row_b2_10 is set to value 15.
                # PSU_DDRC_ADDRMAP9_ADDRMAP_ROW_B5                                                0x8

                # Selects the HIF address bits used as row address bit 4. Valid Range: 0 to 11 Internal Base: 10 The selected HIF address bit f
                # r each of the row address bits is determined by adding the internal base to the value of this field. This register field is u
                # ed only when ADDRMAP5.addrmap_row_b2_10 is set to value 15.
                # PSU_DDRC_ADDRMAP9_ADDRMAP_ROW_B4                                                0x8

                # Selects the HIF address bits used as row address bit 3. Valid Range: 0 to 11 Internal Base: 9 The selected HIF address bit fo
                #  each of the row address bits is determined by adding the internal base to the value of this field. This register field is us
                # d only when ADDRMAP5.addrmap_row_b2_10 is set to value 15.
                # PSU_DDRC_ADDRMAP9_ADDRMAP_ROW_B3                                                0x8

                # Selects the HIF address bits used as row address bit 2. Valid Range: 0 to 11 Internal Base: 8 The selected HIF address bit fo
                #  each of the row address bits is determined by adding the internal base to the value of this field. This register field is us
                # d only when ADDRMAP5.addrmap_row_b2_10 is set to value 15.
                # PSU_DDRC_ADDRMAP9_ADDRMAP_ROW_B2                                                0x8

                # Address Map Register 9
                #(OFFSET, MASK, VALUE)      (0XFD070224, 0x0F0F0F0FU ,0x08080808U)  */
    mask_write 0XFD070224 0x0F0F0F0F 0x08080808
                # Register : ADDRMAP10 @ 0XFD070228</p>

                # Selects the HIF address bits used as row address bit 9. Valid Range: 0 to 11 Internal Base: 15 The selected HIF address bit f
                # r each of the row address bits is determined by adding the internal base to the value of this field. This register field is u
                # ed only when ADDRMAP5.addrmap_row_b2_10 is set to value 15.
                # PSU_DDRC_ADDRMAP10_ADDRMAP_ROW_B9                                               0x8

                # Selects the HIF address bits used as row address bit 8. Valid Range: 0 to 11 Internal Base: 14 The selected HIF address bit f
                # r each of the row address bits is determined by adding the internal base to the value of this field. This register field is u
                # ed only when ADDRMAP5.addrmap_row_b2_10 is set to value 15.
                # PSU_DDRC_ADDRMAP10_ADDRMAP_ROW_B8                                               0x8

                # Selects the HIF address bits used as row address bit 7. Valid Range: 0 to 11 Internal Base: 13 The selected HIF address bit f
                # r each of the row address bits is determined by adding the internal base to the value of this field. This register field is u
                # ed only when ADDRMAP5.addrmap_row_b2_10 is set to value 15.
                # PSU_DDRC_ADDRMAP10_ADDRMAP_ROW_B7                                               0x8

                # Selects the HIF address bits used as row address bit 6. Valid Range: 0 to 11 Internal Base: 12 The selected HIF address bit f
                # r each of the row address bits is determined by adding the internal base to the value of this field. This register field is u
                # ed only when ADDRMAP5.addrmap_row_b2_10 is set to value 15.
                # PSU_DDRC_ADDRMAP10_ADDRMAP_ROW_B6                                               0x8

                # Address Map Register 10
                #(OFFSET, MASK, VALUE)      (0XFD070228, 0x0F0F0F0FU ,0x08080808U)  */
    mask_write 0XFD070228 0x0F0F0F0F 0x08080808
                # Register : ADDRMAP11 @ 0XFD07022C</p>

                # Selects the HIF address bits used as row address bit 10. Valid Range: 0 to 11 Internal Base: 16 The selected HIF address bit 
                # or each of the row address bits is determined by adding the internal base to the value of this field. This register field is 
                # sed only when ADDRMAP5.addrmap_row_b2_10 is set to value 15.
                # PSU_DDRC_ADDRMAP11_ADDRMAP_ROW_B10                                              0x8

                # Address Map Register 11
                #(OFFSET, MASK, VALUE)      (0XFD07022C, 0x0000000FU ,0x00000008U)  */
    mask_write 0XFD07022C 0x0000000F 0x00000008
                # Register : ODTCFG @ 0XFD070240</p>

                # Cycles to hold ODT for a write command. The minimum supported value is 2. Recommended values: DDR2: - BL8: 0x5 (DDR2-400/533/
                # 67), 0x6 (DDR2-800), 0x7 (DDR2-1066) - BL4: 0x3 (DDR2-400/533/667), 0x4 (DDR2-800), 0x5 (DDR2-1066) DDR3: - BL8: 0x6 DDR4: - 
                # L8: 5 + WR_PREAMBLE + CRC_MODE WR_PREAMBLE = 1 (1tCK write preamble), 2 (2tCK write preamble) CRC_MODE = 0 (not CRC mode), 1 
                # CRC mode) LPDDR3: - BL8: 7 + RU(tODTon(max)/tCK)
                # PSU_DDRC_ODTCFG_WR_ODT_HOLD                                                     0x6

                # The delay, in clock cycles, from issuing a write command to setting ODT values associated with that command. ODT setting must
                # remain constant for the entire time that DQS is driven by the uMCTL2. Recommended values: DDR2: - CWL + AL - 3 (DDR2-400/533/
                # 67), CWL + AL - 4 (DDR2-800), CWL + AL - 5 (DDR2-1066) If (CWL + AL - 3 < 0), uMCTL2 does not support ODT for write operation
                #  DDR3: - 0x0 DDR4: - DFITMG1.dfi_t_cmd_lat (to adjust for CAL mode) LPDDR3: - WL - 1 - RU(tODTon(max)/tCK))
                # PSU_DDRC_ODTCFG_WR_ODT_DELAY                                                    0x0

                # Cycles to hold ODT for a read command. The minimum supported value is 2. Recommended values: DDR2: - BL8: 0x6 (not DDR2-1066)
                #  0x7 (DDR2-1066) - BL4: 0x4 (not DDR2-1066), 0x5 (DDR2-1066) DDR3: - BL8 - 0x6 DDR4: - BL8: 5 + RD_PREAMBLE RD_PREAMBLE = 1 (
                # tCK write preamble), 2 (2tCK write preamble) LPDDR3: - BL8: 5 + RU(tDQSCK(max)/tCK) - RD(tDQSCK(min)/tCK) + RU(tODTon(max)/tC
                # )
                # PSU_DDRC_ODTCFG_RD_ODT_HOLD                                                     0x6

                # The delay, in clock cycles, from issuing a read command to setting ODT values associated with that command. ODT setting must 
                # emain constant for the entire time that DQS is driven by the uMCTL2. Recommended values: DDR2: - CL + AL - 4 (not DDR2-1066),
                # CL + AL - 5 (DDR2-1066) If (CL + AL - 4 < 0), uMCTL2 does not support ODT for read operation. DDR3: - CL - CWL DDR4: - CL - C
                # L - RD_PREAMBLE + WR_PREAMBLE + DFITMG1.dfi_t_cmd_lat (to adjust for CAL mode) WR_PREAMBLE = 1 (1tCK write preamble), 2 (2tCK
                # write preamble) RD_PREAMBLE = 1 (1tCK write preamble), 2 (2tCK write preamble) If (CL - CWL - RD_PREAMBLE + WR_PREAMBLE) < 0,
                # uMCTL2 does not support ODT for read operation. LPDDR3: - RL + RD(tDQSCK(min)/tCK) - 1 - RU(tODTon(max)/tCK)
                # PSU_DDRC_ODTCFG_RD_ODT_DELAY                                                    0x0

                # ODT Configuration Register
                #(OFFSET, MASK, VALUE)      (0XFD070240, 0x0F1F0F7CU ,0x06000600U)  */
    mask_write 0XFD070240 0x0F1F0F7C 0x06000600
                # Register : ODTMAP @ 0XFD070244</p>

                # Indicates which remote ODTs must be turned on during a read from rank 1. Each rank has a remote ODT (in the SDRAM) which can 
                # e turned on by setting the appropriate bit here. Rank 0 is controlled by the LSB; rank 1 is controlled by bit next to the LSB
                #  etc. For each rank, set its bit to 1 to enable its ODT. Present only in configurations that have 2 or more ranks
                # PSU_DDRC_ODTMAP_RANK1_RD_ODT                                                    0x0

                # Indicates which remote ODTs must be turned on during a write to rank 1. Each rank has a remote ODT (in the SDRAM) which can b
                #  turned on by setting the appropriate bit here. Rank 0 is controlled by the LSB; rank 1 is controlled by bit next to the LSB,
                # etc. For each rank, set its bit to 1 to enable its ODT. Present only in configurations that have 2 or more ranks
                # PSU_DDRC_ODTMAP_RANK1_WR_ODT                                                    0x0

                # Indicates which remote ODTs must be turned on during a read from rank 0. Each rank has a remote ODT (in the SDRAM) which can 
                # e turned on by setting the appropriate bit here. Rank 0 is controlled by the LSB; rank 1 is controlled by bit next to the LSB
                #  etc. For each rank, set its bit to 1 to enable its ODT.
                # PSU_DDRC_ODTMAP_RANK0_RD_ODT                                                    0x0

                # Indicates which remote ODTs must be turned on during a write to rank 0. Each rank has a remote ODT (in the SDRAM) which can b
                #  turned on by setting the appropriate bit here. Rank 0 is controlled by the LSB; rank 1 is controlled by bit next to the LSB,
                # etc. For each rank, set its bit to 1 to enable its ODT.
                # PSU_DDRC_ODTMAP_RANK0_WR_ODT                                                    0x1

                # ODT/Rank Map Register
                #(OFFSET, MASK, VALUE)      (0XFD070244, 0x00003333U ,0x00000001U)  */
    mask_write 0XFD070244 0x00003333 0x00000001
                # Register : SCHED @ 0XFD070250</p>

                # When the preferred transaction store is empty for these many clock cycles, switch to the alternate transaction store if it is
                # non-empty. The read transaction store (both high and low priority) is the default preferred transaction store and the write t
                # ansaction store is the alternative store. When prefer write over read is set this is reversed. 0x0 is a legal value for this 
                # egister. When set to 0x0, the transaction store switching will happen immediately when the switching conditions become true. 
                # OR PERFORMANCE ONLY
                # PSU_DDRC_SCHED_RDWR_IDLE_GAP                                                    0x1

                # UNUSED
                # PSU_DDRC_SCHED_GO2CRITICAL_HYSTERESIS                                           0x0

                # Number of entries in the low priority transaction store is this value + 1. (MEMC_NO_OF_ENTRY - (SCHED.lpr_num_entries + 1)) i
                #  the number of entries available for the high priority transaction store. Setting this to maximum value allocates all entries
                # to low priority transaction store. Setting this to 0 allocates 1 entry to low priority transaction store and the rest to high
                # priority transaction store. Note: In ECC configurations, the numbers of write and low priority read credits issued is one les
                #  than in the non-ECC case. One entry each is reserved in the write and low-priority read CAMs for storing the RMW requests ar
                # sing out of single bit error correction RMW operation.
                # PSU_DDRC_SCHED_LPR_NUM_ENTRIES                                                  0x20

                # If true, bank is kept open only while there are page hit transactions available in the CAM to that bank. The last read or wri
                # e command in the CAM with a bank and page hit will be executed with auto-precharge if SCHED1.pageclose_timer=0. Even if this 
                # egister set to 1 and SCHED1.pageclose_timer is set to 0, explicit precharge (and not auto-precharge) may be issued in some ca
                # es where there is a mode switch between Write and Read or between LPR and HPR. The Read and Write commands that are executed 
                # s part of the ECC scrub requests are also executed without auto-precharge. If false, the bank remains open until there is a n
                # ed to close it (to open a different page, or for page timeout or refresh timeout) - also known as open page policy. The open 
                # age policy can be overridden by setting the per-command-autopre bit on the HIF interface (hif_cmd_autopre). The pageclose fea
                # ure provids a midway between Open and Close page policies. FOR PERFORMANCE ONLY.
                # PSU_DDRC_SCHED_PAGECLOSE                                                        0x0

                # If set then the bank selector prefers writes over reads. FOR DEBUG ONLY.
                # PSU_DDRC_SCHED_PREFER_WRITE                                                     0x0

                # Active low signal. When asserted ('0'), all incoming transactions are forced to low priority. This implies that all High Prio
                # ity Read (HPR) and Variable Priority Read commands (VPR) will be treated as Low Priority Read (LPR) commands. On the write si
                # e, all Variable Priority Write (VPW) commands will be treated as Normal Priority Write (NPW) commands. Forcing the incoming t
                # ansactions to low priority implicitly turns off Bypass path for read commands. FOR PERFORMANCE ONLY.
                # PSU_DDRC_SCHED_FORCE_LOW_PRI_N                                                  0x1

                # Scheduler Control Register
                #(OFFSET, MASK, VALUE)      (0XFD070250, 0x7FFF3F07U ,0x01002001U)  */
    mask_write 0XFD070250 0x7FFF3F07 0x01002001
                # Register : PERFLPR1 @ 0XFD070264</p>

                # Number of transactions that are serviced once the LPR queue goes critical is the smaller of: - (a) This number - (b) Number o
                #  transactions available. Unit: Transaction. FOR PERFORMANCE ONLY.
                # PSU_DDRC_PERFLPR1_LPR_XACT_RUN_LENGTH                                           0x8

                # Number of clocks that the LPR queue can be starved before it goes critical. The minimum valid functional value for this regis
                # er is 0x1. Programming it to 0x0 will disable the starvation functionality; during normal operation, this function should not
                # be disabled as it will cause excessive latencies. Unit: Clock cycles. FOR PERFORMANCE ONLY.
                # PSU_DDRC_PERFLPR1_LPR_MAX_STARVE                                                0x40

                # Low Priority Read CAM Register 1
                #(OFFSET, MASK, VALUE)      (0XFD070264, 0xFF00FFFFU ,0x08000040U)  */
    mask_write 0XFD070264 0xFF00FFFF 0x08000040
                # Register : PERFWR1 @ 0XFD07026C</p>

                # Number of transactions that are serviced once the WR queue goes critical is the smaller of: - (a) This number - (b) Number of
                # transactions available. Unit: Transaction. FOR PERFORMANCE ONLY.
                # PSU_DDRC_PERFWR1_W_XACT_RUN_LENGTH                                              0x8

                # Number of clocks that the WR queue can be starved before it goes critical. The minimum valid functional value for this regist
                # r is 0x1. Programming it to 0x0 will disable the starvation functionality; during normal operation, this function should not 
                # e disabled as it will cause excessive latencies. Unit: Clock cycles. FOR PERFORMANCE ONLY.
                # PSU_DDRC_PERFWR1_W_MAX_STARVE                                                   0x40

                # Write CAM Register 1
                #(OFFSET, MASK, VALUE)      (0XFD07026C, 0xFF00FFFFU ,0x08000040U)  */
    mask_write 0XFD07026C 0xFF00FFFF 0x08000040
                # Register : DQMAP5 @ 0XFD070294</p>

                # All even ranks have the same DQ mapping controled by DQMAP0-4 register as rank 0. This register provides DQ swap function for
                # all odd ranks to support CRC feature. rank based DQ swapping is: swap bit 0 with 1, swap bit 2 with 3, swap bit 4 with 5 and 
                # wap bit 6 with 7. 1: Disable rank based DQ swapping 0: Enable rank based DQ swapping Present only in designs configured to su
                # port DDR4.
                # PSU_DDRC_DQMAP5_DIS_DQ_RANK_SWAP                                                0x1

                # DQ Map Register 5
                #(OFFSET, MASK, VALUE)      (0XFD070294, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD070294 0x00000001 0x00000001
                # Register : DBG0 @ 0XFD070300</p>

                # When this is set to '0', auto-precharge is disabled for the flushed command in a collision case. Collision cases are write fo
                # lowed by read to same address, read followed by write to same address, or write followed by write to same address with DBG0.d
                # s_wc bit = 1 (where same address comparisons exclude the two address bits representing critical word). FOR DEBUG ONLY.
                # PSU_DDRC_DBG0_DIS_COLLISION_PAGE_OPT                                            0x0

                # When 1, disable write combine. FOR DEBUG ONLY
                # PSU_DDRC_DBG0_DIS_WC                                                            0x0

                # Debug Register 0
                #(OFFSET, MASK, VALUE)      (0XFD070300, 0x00000011U ,0x00000000U)  */
    mask_write 0XFD070300 0x00000011 0x00000000
                # Register : DBGCMD @ 0XFD07030C</p>

                # Setting this register bit to 1 allows refresh and ZQCS commands to be triggered from hardware via the IOs ext_*. If set to 1,
                # the fields DBGCMD.zq_calib_short and DBGCMD.rank*_refresh have no function, and are ignored by the uMCTL2 logic. Setting this
                # register bit to 0 allows refresh and ZQCS to be triggered from software, via the fields DBGCMD.zq_calib_short and DBGCMD.rank
                # _refresh. If set to 0, the hardware pins ext_* have no function, and are ignored by the uMCTL2 logic. This register is static
                #  and may only be changed when the DDRC reset signal, core_ddrc_rstn, is asserted (0).
                # PSU_DDRC_DBGCMD_HW_REF_ZQ_EN                                                    0x0

                # Setting this register bit to 1 indicates to the uMCTL2 to issue a dfi_ctrlupd_req to the PHY. When this request is stored in 
                # he uMCTL2, the bit is automatically cleared. This operation must only be performed when DFIUPD0.dis_auto_ctrlupd=1.
                # PSU_DDRC_DBGCMD_CTRLUPD                                                         0x0

                # Setting this register bit to 1 indicates to the uMCTL2 to issue a ZQCS (ZQ calibration short)/MPC(ZQ calibration) command to 
                # he SDRAM. When this request is stored in the uMCTL2, the bit is automatically cleared. This operation can be performed only w
                # en ZQCTL0.dis_auto_zq=1. It is recommended NOT to set this register bit if in Init operating mode. This register bit is ignor
                # d when in Self-Refresh(except LPDDR4) and SR-Powerdown(LPDDR4) and Deep power-down operating modes and Maximum Power Saving M
                # de.
                # PSU_DDRC_DBGCMD_ZQ_CALIB_SHORT                                                  0x0

                # Setting this register bit to 1 indicates to the uMCTL2 to issue a refresh to rank 1. Writing to this bit causes DBGSTAT.rank1
                # refresh_busy to be set. When DBGSTAT.rank1_refresh_busy is cleared, the command has been stored in uMCTL2. This operation can
                # be performed only when RFSHCTL3.dis_auto_refresh=1. It is recommended NOT to set this register bit if in Init or Deep power-d
                # wn operating modes or Maximum Power Saving Mode.
                # PSU_DDRC_DBGCMD_RANK1_REFRESH                                                   0x0

                # Setting this register bit to 1 indicates to the uMCTL2 to issue a refresh to rank 0. Writing to this bit causes DBGSTAT.rank0
                # refresh_busy to be set. When DBGSTAT.rank0_refresh_busy is cleared, the command has been stored in uMCTL2. This operation can
                # be performed only when RFSHCTL3.dis_auto_refresh=1. It is recommended NOT to set this register bit if in Init or Deep power-d
                # wn operating modes or Maximum Power Saving Mode.
                # PSU_DDRC_DBGCMD_RANK0_REFRESH                                                   0x0

                # Command Debug Register
                #(OFFSET, MASK, VALUE)      (0XFD07030C, 0x80000033U ,0x00000000U)  */
    mask_write 0XFD07030C 0x80000033 0x00000000
                # Register : SWCTL @ 0XFD070320</p>

                # Enable quasi-dynamic register programming outside reset. Program register to 0 to enable quasi-dynamic programming. Set back 
                # egister to 1 once programming is done.
                # PSU_DDRC_SWCTL_SW_DONE                                                          0x0

                # Software register programming control enable
                #(OFFSET, MASK, VALUE)      (0XFD070320, 0x00000001U ,0x00000000U)  */
    mask_write 0XFD070320 0x00000001 0x00000000
                # Register : PCCFG @ 0XFD070400</p>

                # Burst length expansion mode. By default (i.e. bl_exp_mode==0) XPI expands every AXI burst into multiple HIF commands, using t
                # e memory burst length as a unit. If set to 1, then XPI will use half of the memory burst length as a unit. This applies to bo
                # h reads and writes. When MSTR.data_bus_width==00, setting bl_exp_mode to 1 has no effect. This can be used in cases where Par
                # ial Writes is enabled (UMCTL2_PARTIAL_WR=1) and DBG0.dis_wc=1, in order to avoid or minimize t_ccd_l penalty in DDR4 and t_cc
                # _mw penalty in LPDDR4. Note that if DBICTL.reg_ddrc_dm_en=0, functionality is not supported in the following cases: - UMCTL2_
                # ARTIAL_WR=0 - UMCTL2_PARTIAL_WR=1, MSTR.reg_ddrc_data_bus_width=01, MEMC_BURST_LENGTH=8 and MSTR.reg_ddrc_burst_rdwr=1000 (LP
                # DR4 only) - UMCTL2_PARTIAL_WR=1, MSTR.reg_ddrc_data_bus_width=01, MEMC_BURST_LENGTH=4 and MSTR.reg_ddrc_burst_rdwr=0100 (DDR4
                # only), with either MSTR.reg_ddrc_burstchop=0 or CRCPARCTL1.reg_ddrc_crc_enable=1 Functionality is also not supported if Share
                # -AC is enabled
                # PSU_DDRC_PCCFG_BL_EXP_MODE                                                      0x0

                # Page match four limit. If set to 1, limits the number of consecutive same page DDRC transactions that can be granted by the P
                # rt Arbiter to four when Page Match feature is enabled. If set to 0, there is no limit imposed on number of consecutive same p
                # ge DDRC transactions.
                # PSU_DDRC_PCCFG_PAGEMATCH_LIMIT                                                  0x0

                # If set to 1 (enabled), sets co_gs_go2critical_wr and co_gs_go2critical_lpr/co_gs_go2critical_hpr signals going to DDRC based 
                # n urgent input (awurgent, arurgent) coming from AXI master. If set to 0 (disabled), co_gs_go2critical_wr and co_gs_go2critica
                # _lpr/co_gs_go2critical_hpr signals at DDRC are driven to 1b'0.
                # PSU_DDRC_PCCFG_GO2CRITICAL_EN                                                   0x1

                # Port Common Configuration Register
                #(OFFSET, MASK, VALUE)      (0XFD070400, 0x00000111U ,0x00000001U)  */
    mask_write 0XFD070400 0x00000111 0x00000001
                # Register : PCFGR_0 @ 0XFD070404</p>

                # If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant
                # d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_
                # imit register.
                # PSU_DDRC_PCFGR_0_RD_PORT_PAGEMATCH_EN                                           0x0

                # If set to 1, enables the AXI urgent sideband signal (arurgent). When enabled and arurgent is asserted by the master, that por
                #  becomes the highest priority and co_gs_go2critical_lpr/co_gs_go2critical_hpr signal to DDRC is asserted if enabled in PCCFG.
                # o2critical_en register. Note that arurgent signal can be asserted anytime and as long as required which is independent of add
                # ess handshaking (it is not associated with any particular command).
                # PSU_DDRC_PCFGR_0_RD_PORT_URGENT_EN                                              0x1

                # If set to 1, enables aging function for the read channel of the port.
                # PSU_DDRC_PCFGR_0_RD_PORT_AGING_EN                                               0x0

                # Determines the initial load value of read aging counters. These counters will be parallel loaded after reset, or after each g
                # ant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. 
                # he higher significant 5-bits of the read aging counter sets the priority of the read channel of a given port. Port's priority
                # will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0, the corre
                # ponding port channel will have the highest priority level (timeout condition - Priority0). For multi-port configurations, the
                # aging counters cannot be used to set port priorities when external dynamic priority inputs (arqos) are enabled (timeout is st
                # ll applicable). For single port configurations, the aging counters are only used when they timeout (become 0) to force read-w
                # ite direction switching. In this case, external dynamic priority input, arqos (for reads only) can still be used to set the D
                # RC read priority (2 priority levels: low priority read - LPR, high priority read - HPR) on a command by command basis. Note: 
                # he two LSBs of this register field are tied internally to 2'b00.
                # PSU_DDRC_PCFGR_0_RD_PORT_PRIORITY                                               0xf

                # Port n Configuration Read Register
                #(OFFSET, MASK, VALUE)      (0XFD070404, 0x000073FFU ,0x0000200FU)  */
    mask_write 0XFD070404 0x000073FF 0x0000200F
                # Register : PCFGW_0 @ 0XFD070408</p>

                # If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant
                # d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_
                # imit register.
                # PSU_DDRC_PCFGW_0_WR_PORT_PAGEMATCH_EN                                           0x1

                # If set to 1, enables the AXI urgent sideband signal (awurgent). When enabled and awurgent is asserted by the master, that por
                #  becomes the highest priority and co_gs_go2critical_wr signal to DDRC is asserted if enabled in PCCFG.go2critical_en register
                #  Note that awurgent signal can be asserted anytime and as long as required which is independent of address handshaking (it is
                # not associated with any particular command).
                # PSU_DDRC_PCFGW_0_WR_PORT_URGENT_EN                                              0x1

                # If set to 1, enables aging function for the write channel of the port.
                # PSU_DDRC_PCFGW_0_WR_PORT_AGING_EN                                               0x0

                # Determines the initial load value of write aging counters. These counters will be parallel loaded after reset, or after each 
                # rant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted.
                # The higher significant 5-bits of the write aging counter sets the initial priority of the write channel of a given port. Port
                # s priority will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0
                #  the corresponding port channel will have the highest priority level. For multi-port configurations, the aging counters canno
                #  be used to set port priorities when external dynamic priority inputs (awqos) are enabled (timeout is still applicable). For 
                # ingle port configurations, the aging counters are only used when they timeout (become 0) to force read-write direction switch
                # ng. Note: The two LSBs of this register field are tied internally to 2'b00.
                # PSU_DDRC_PCFGW_0_WR_PORT_PRIORITY                                               0xf

                # Port n Configuration Write Register
                #(OFFSET, MASK, VALUE)      (0XFD070408, 0x000073FFU ,0x0000600FU)  */
    mask_write 0XFD070408 0x000073FF 0x0000600F
                # Register : PCTRL_0 @ 0XFD070490</p>

                # Enables port n.
                # PSU_DDRC_PCTRL_0_PORT_EN                                                        0x1

                # Port n Control Register
                #(OFFSET, MASK, VALUE)      (0XFD070490, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD070490 0x00000001 0x00000001
                # Register : PCFGQOS0_0 @ 0XFD070494</p>

                # This bitfield indicates the traffic class of region 1. Valid values are: 0 : LPR, 1: VPR, 2: HPR. For dual address queue conf
                # gurations, region1 maps to the blue address queue. In this case, valid values are 0: LPR and 1: VPR only. When VPR support is
                # disabled (UMCTL2_VPR_EN = 0) and traffic class of region 1 is set to 1 (VPR), VPR traffic is aliased to LPR traffic.
                # PSU_DDRC_PCFGQOS0_0_RQOS_MAP_REGION1                                            0x2

                # This bitfield indicates the traffic class of region 0. Valid values are: 0: LPR, 1: VPR, 2: HPR. For dual address queue confi
                # urations, region 0 maps to the blue address queue. In this case, valid values are: 0: LPR and 1: VPR only. When VPR support i
                #  disabled (UMCTL2_VPR_EN = 0) and traffic class of region0 is set to 1 (VPR), VPR traffic is aliased to LPR traffic.
                # PSU_DDRC_PCFGQOS0_0_RQOS_MAP_REGION0                                            0x0

                # Separation level1 indicating the end of region0 mapping; start of region0 is 0. Possible values for level1 are 0 to 13 (for d
                # al RAQ) or 0 to 14 (for single RAQ) which corresponds to arqos. Note that for PA, arqos values are used directly as port prio
                # ities, where the higher the value corresponds to higher port priority. All of the map_level* registers must be set to distinc
                #  values.
                # PSU_DDRC_PCFGQOS0_0_RQOS_MAP_LEVEL1                                             0xb

                # Port n Read QoS Configuration Register 0
                #(OFFSET, MASK, VALUE)      (0XFD070494, 0x0033000FU ,0x0020000BU)  */
    mask_write 0XFD070494 0x0033000F 0x0020000B
                # Register : PCFGQOS1_0 @ 0XFD070498</p>

                # Specifies the timeout value for transactions mapped to the red address queue.
                # PSU_DDRC_PCFGQOS1_0_RQOS_MAP_TIMEOUTR                                           0x0

                # Specifies the timeout value for transactions mapped to the blue address queue.
                # PSU_DDRC_PCFGQOS1_0_RQOS_MAP_TIMEOUTB                                           0x0

                # Port n Read QoS Configuration Register 1
                #(OFFSET, MASK, VALUE)      (0XFD070498, 0x07FF07FFU ,0x00000000U)  */
    mask_write 0XFD070498 0x07FF07FF 0x00000000
                # Register : PCFGR_1 @ 0XFD0704B4</p>

                # If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant
                # d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_
                # imit register.
                # PSU_DDRC_PCFGR_1_RD_PORT_PAGEMATCH_EN                                           0x0

                # If set to 1, enables the AXI urgent sideband signal (arurgent). When enabled and arurgent is asserted by the master, that por
                #  becomes the highest priority and co_gs_go2critical_lpr/co_gs_go2critical_hpr signal to DDRC is asserted if enabled in PCCFG.
                # o2critical_en register. Note that arurgent signal can be asserted anytime and as long as required which is independent of add
                # ess handshaking (it is not associated with any particular command).
                # PSU_DDRC_PCFGR_1_RD_PORT_URGENT_EN                                              0x1

                # If set to 1, enables aging function for the read channel of the port.
                # PSU_DDRC_PCFGR_1_RD_PORT_AGING_EN                                               0x0

                # Determines the initial load value of read aging counters. These counters will be parallel loaded after reset, or after each g
                # ant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. 
                # he higher significant 5-bits of the read aging counter sets the priority of the read channel of a given port. Port's priority
                # will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0, the corre
                # ponding port channel will have the highest priority level (timeout condition - Priority0). For multi-port configurations, the
                # aging counters cannot be used to set port priorities when external dynamic priority inputs (arqos) are enabled (timeout is st
                # ll applicable). For single port configurations, the aging counters are only used when they timeout (become 0) to force read-w
                # ite direction switching. In this case, external dynamic priority input, arqos (for reads only) can still be used to set the D
                # RC read priority (2 priority levels: low priority read - LPR, high priority read - HPR) on a command by command basis. Note: 
                # he two LSBs of this register field are tied internally to 2'b00.
                # PSU_DDRC_PCFGR_1_RD_PORT_PRIORITY                                               0xf

                # Port n Configuration Read Register
                #(OFFSET, MASK, VALUE)      (0XFD0704B4, 0x000073FFU ,0x0000200FU)  */
    mask_write 0XFD0704B4 0x000073FF 0x0000200F
                # Register : PCFGW_1 @ 0XFD0704B8</p>

                # If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant
                # d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_
                # imit register.
                # PSU_DDRC_PCFGW_1_WR_PORT_PAGEMATCH_EN                                           0x1

                # If set to 1, enables the AXI urgent sideband signal (awurgent). When enabled and awurgent is asserted by the master, that por
                #  becomes the highest priority and co_gs_go2critical_wr signal to DDRC is asserted if enabled in PCCFG.go2critical_en register
                #  Note that awurgent signal can be asserted anytime and as long as required which is independent of address handshaking (it is
                # not associated with any particular command).
                # PSU_DDRC_PCFGW_1_WR_PORT_URGENT_EN                                              0x1

                # If set to 1, enables aging function for the write channel of the port.
                # PSU_DDRC_PCFGW_1_WR_PORT_AGING_EN                                               0x0

                # Determines the initial load value of write aging counters. These counters will be parallel loaded after reset, or after each 
                # rant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted.
                # The higher significant 5-bits of the write aging counter sets the initial priority of the write channel of a given port. Port
                # s priority will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0
                #  the corresponding port channel will have the highest priority level. For multi-port configurations, the aging counters canno
                #  be used to set port priorities when external dynamic priority inputs (awqos) are enabled (timeout is still applicable). For 
                # ingle port configurations, the aging counters are only used when they timeout (become 0) to force read-write direction switch
                # ng. Note: The two LSBs of this register field are tied internally to 2'b00.
                # PSU_DDRC_PCFGW_1_WR_PORT_PRIORITY                                               0xf

                # Port n Configuration Write Register
                #(OFFSET, MASK, VALUE)      (0XFD0704B8, 0x000073FFU ,0x0000600FU)  */
    mask_write 0XFD0704B8 0x000073FF 0x0000600F
                # Register : PCTRL_1 @ 0XFD070540</p>

                # Enables port n.
                # PSU_DDRC_PCTRL_1_PORT_EN                                                        0x1

                # Port n Control Register
                #(OFFSET, MASK, VALUE)      (0XFD070540, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD070540 0x00000001 0x00000001
                # Register : PCFGQOS0_1 @ 0XFD070544</p>

                # This bitfield indicates the traffic class of region2. For dual address queue configurations, region2 maps to the red address 
                # ueue. Valid values are 1: VPR and 2: HPR only. When VPR support is disabled (UMCTL2_VPR_EN = 0) and traffic class of region2 
                # s set to 1 (VPR), VPR traffic is aliased to LPR traffic.
                # PSU_DDRC_PCFGQOS0_1_RQOS_MAP_REGION2                                            0x2

                # This bitfield indicates the traffic class of region 1. Valid values are: 0 : LPR, 1: VPR, 2: HPR. For dual address queue conf
                # gurations, region1 maps to the blue address queue. In this case, valid values are 0: LPR and 1: VPR only. When VPR support is
                # disabled (UMCTL2_VPR_EN = 0) and traffic class of region 1 is set to 1 (VPR), VPR traffic is aliased to LPR traffic.
                # PSU_DDRC_PCFGQOS0_1_RQOS_MAP_REGION1                                            0x0

                # This bitfield indicates the traffic class of region 0. Valid values are: 0: LPR, 1: VPR, 2: HPR. For dual address queue confi
                # urations, region 0 maps to the blue address queue. In this case, valid values are: 0: LPR and 1: VPR only. When VPR support i
                #  disabled (UMCTL2_VPR_EN = 0) and traffic class of region0 is set to 1 (VPR), VPR traffic is aliased to LPR traffic.
                # PSU_DDRC_PCFGQOS0_1_RQOS_MAP_REGION0                                            0x0

                # Separation level2 indicating the end of region1 mapping; start of region1 is (level1 + 1). Possible values for level2 are (le
                # el1 + 1) to 14 which corresponds to arqos. Region2 starts from (level2 + 1) up to 15. Note that for PA, arqos values are used
                # directly as port priorities, where the higher the value corresponds to higher port priority. All of the map_level* registers 
                # ust be set to distinct values.
                # PSU_DDRC_PCFGQOS0_1_RQOS_MAP_LEVEL2                                             0xb

                # Separation level1 indicating the end of region0 mapping; start of region0 is 0. Possible values for level1 are 0 to 13 (for d
                # al RAQ) or 0 to 14 (for single RAQ) which corresponds to arqos. Note that for PA, arqos values are used directly as port prio
                # ities, where the higher the value corresponds to higher port priority. All of the map_level* registers must be set to distinc
                #  values.
                # PSU_DDRC_PCFGQOS0_1_RQOS_MAP_LEVEL1                                             0x3

                # Port n Read QoS Configuration Register 0
                #(OFFSET, MASK, VALUE)      (0XFD070544, 0x03330F0FU ,0x02000B03U)  */
    mask_write 0XFD070544 0x03330F0F 0x02000B03
                # Register : PCFGQOS1_1 @ 0XFD070548</p>

                # Specifies the timeout value for transactions mapped to the red address queue.
                # PSU_DDRC_PCFGQOS1_1_RQOS_MAP_TIMEOUTR                                           0x0

                # Specifies the timeout value for transactions mapped to the blue address queue.
                # PSU_DDRC_PCFGQOS1_1_RQOS_MAP_TIMEOUTB                                           0x0

                # Port n Read QoS Configuration Register 1
                #(OFFSET, MASK, VALUE)      (0XFD070548, 0x07FF07FFU ,0x00000000U)  */
    mask_write 0XFD070548 0x07FF07FF 0x00000000
                # Register : PCFGR_2 @ 0XFD070564</p>

                # If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant
                # d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_
                # imit register.
                # PSU_DDRC_PCFGR_2_RD_PORT_PAGEMATCH_EN                                           0x0

                # If set to 1, enables the AXI urgent sideband signal (arurgent). When enabled and arurgent is asserted by the master, that por
                #  becomes the highest priority and co_gs_go2critical_lpr/co_gs_go2critical_hpr signal to DDRC is asserted if enabled in PCCFG.
                # o2critical_en register. Note that arurgent signal can be asserted anytime and as long as required which is independent of add
                # ess handshaking (it is not associated with any particular command).
                # PSU_DDRC_PCFGR_2_RD_PORT_URGENT_EN                                              0x1

                # If set to 1, enables aging function for the read channel of the port.
                # PSU_DDRC_PCFGR_2_RD_PORT_AGING_EN                                               0x0

                # Determines the initial load value of read aging counters. These counters will be parallel loaded after reset, or after each g
                # ant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. 
                # he higher significant 5-bits of the read aging counter sets the priority of the read channel of a given port. Port's priority
                # will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0, the corre
                # ponding port channel will have the highest priority level (timeout condition - Priority0). For multi-port configurations, the
                # aging counters cannot be used to set port priorities when external dynamic priority inputs (arqos) are enabled (timeout is st
                # ll applicable). For single port configurations, the aging counters are only used when they timeout (become 0) to force read-w
                # ite direction switching. In this case, external dynamic priority input, arqos (for reads only) can still be used to set the D
                # RC read priority (2 priority levels: low priority read - LPR, high priority read - HPR) on a command by command basis. Note: 
                # he two LSBs of this register field are tied internally to 2'b00.
                # PSU_DDRC_PCFGR_2_RD_PORT_PRIORITY                                               0xf

                # Port n Configuration Read Register
                #(OFFSET, MASK, VALUE)      (0XFD070564, 0x000073FFU ,0x0000200FU)  */
    mask_write 0XFD070564 0x000073FF 0x0000200F
                # Register : PCFGW_2 @ 0XFD070568</p>

                # If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant
                # d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_
                # imit register.
                # PSU_DDRC_PCFGW_2_WR_PORT_PAGEMATCH_EN                                           0x1

                # If set to 1, enables the AXI urgent sideband signal (awurgent). When enabled and awurgent is asserted by the master, that por
                #  becomes the highest priority and co_gs_go2critical_wr signal to DDRC is asserted if enabled in PCCFG.go2critical_en register
                #  Note that awurgent signal can be asserted anytime and as long as required which is independent of address handshaking (it is
                # not associated with any particular command).
                # PSU_DDRC_PCFGW_2_WR_PORT_URGENT_EN                                              0x1

                # If set to 1, enables aging function for the write channel of the port.
                # PSU_DDRC_PCFGW_2_WR_PORT_AGING_EN                                               0x0

                # Determines the initial load value of write aging counters. These counters will be parallel loaded after reset, or after each 
                # rant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted.
                # The higher significant 5-bits of the write aging counter sets the initial priority of the write channel of a given port. Port
                # s priority will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0
                #  the corresponding port channel will have the highest priority level. For multi-port configurations, the aging counters canno
                #  be used to set port priorities when external dynamic priority inputs (awqos) are enabled (timeout is still applicable). For 
                # ingle port configurations, the aging counters are only used when they timeout (become 0) to force read-write direction switch
                # ng. Note: The two LSBs of this register field are tied internally to 2'b00.
                # PSU_DDRC_PCFGW_2_WR_PORT_PRIORITY                                               0xf

                # Port n Configuration Write Register
                #(OFFSET, MASK, VALUE)      (0XFD070568, 0x000073FFU ,0x0000600FU)  */
    mask_write 0XFD070568 0x000073FF 0x0000600F
                # Register : PCTRL_2 @ 0XFD0705F0</p>

                # Enables port n.
                # PSU_DDRC_PCTRL_2_PORT_EN                                                        0x1

                # Port n Control Register
                #(OFFSET, MASK, VALUE)      (0XFD0705F0, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD0705F0 0x00000001 0x00000001
                # Register : PCFGQOS0_2 @ 0XFD0705F4</p>

                # This bitfield indicates the traffic class of region2. For dual address queue configurations, region2 maps to the red address 
                # ueue. Valid values are 1: VPR and 2: HPR only. When VPR support is disabled (UMCTL2_VPR_EN = 0) and traffic class of region2 
                # s set to 1 (VPR), VPR traffic is aliased to LPR traffic.
                # PSU_DDRC_PCFGQOS0_2_RQOS_MAP_REGION2                                            0x2

                # This bitfield indicates the traffic class of region 1. Valid values are: 0 : LPR, 1: VPR, 2: HPR. For dual address queue conf
                # gurations, region1 maps to the blue address queue. In this case, valid values are 0: LPR and 1: VPR only. When VPR support is
                # disabled (UMCTL2_VPR_EN = 0) and traffic class of region 1 is set to 1 (VPR), VPR traffic is aliased to LPR traffic.
                # PSU_DDRC_PCFGQOS0_2_RQOS_MAP_REGION1                                            0x0

                # This bitfield indicates the traffic class of region 0. Valid values are: 0: LPR, 1: VPR, 2: HPR. For dual address queue confi
                # urations, region 0 maps to the blue address queue. In this case, valid values are: 0: LPR and 1: VPR only. When VPR support i
                #  disabled (UMCTL2_VPR_EN = 0) and traffic class of region0 is set to 1 (VPR), VPR traffic is aliased to LPR traffic.
                # PSU_DDRC_PCFGQOS0_2_RQOS_MAP_REGION0                                            0x0

                # Separation level2 indicating the end of region1 mapping; start of region1 is (level1 + 1). Possible values for level2 are (le
                # el1 + 1) to 14 which corresponds to arqos. Region2 starts from (level2 + 1) up to 15. Note that for PA, arqos values are used
                # directly as port priorities, where the higher the value corresponds to higher port priority. All of the map_level* registers 
                # ust be set to distinct values.
                # PSU_DDRC_PCFGQOS0_2_RQOS_MAP_LEVEL2                                             0xb

                # Separation level1 indicating the end of region0 mapping; start of region0 is 0. Possible values for level1 are 0 to 13 (for d
                # al RAQ) or 0 to 14 (for single RAQ) which corresponds to arqos. Note that for PA, arqos values are used directly as port prio
                # ities, where the higher the value corresponds to higher port priority. All of the map_level* registers must be set to distinc
                #  values.
                # PSU_DDRC_PCFGQOS0_2_RQOS_MAP_LEVEL1                                             0x3

                # Port n Read QoS Configuration Register 0
                #(OFFSET, MASK, VALUE)      (0XFD0705F4, 0x03330F0FU ,0x02000B03U)  */
    mask_write 0XFD0705F4 0x03330F0F 0x02000B03
                # Register : PCFGQOS1_2 @ 0XFD0705F8</p>

                # Specifies the timeout value for transactions mapped to the red address queue.
                # PSU_DDRC_PCFGQOS1_2_RQOS_MAP_TIMEOUTR                                           0x0

                # Specifies the timeout value for transactions mapped to the blue address queue.
                # PSU_DDRC_PCFGQOS1_2_RQOS_MAP_TIMEOUTB                                           0x0

                # Port n Read QoS Configuration Register 1
                #(OFFSET, MASK, VALUE)      (0XFD0705F8, 0x07FF07FFU ,0x00000000U)  */
    mask_write 0XFD0705F8 0x07FF07FF 0x00000000
                # Register : PCFGR_3 @ 0XFD070614</p>

                # If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant
                # d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_
                # imit register.
                # PSU_DDRC_PCFGR_3_RD_PORT_PAGEMATCH_EN                                           0x0

                # If set to 1, enables the AXI urgent sideband signal (arurgent). When enabled and arurgent is asserted by the master, that por
                #  becomes the highest priority and co_gs_go2critical_lpr/co_gs_go2critical_hpr signal to DDRC is asserted if enabled in PCCFG.
                # o2critical_en register. Note that arurgent signal can be asserted anytime and as long as required which is independent of add
                # ess handshaking (it is not associated with any particular command).
                # PSU_DDRC_PCFGR_3_RD_PORT_URGENT_EN                                              0x1

                # If set to 1, enables aging function for the read channel of the port.
                # PSU_DDRC_PCFGR_3_RD_PORT_AGING_EN                                               0x0

                # Determines the initial load value of read aging counters. These counters will be parallel loaded after reset, or after each g
                # ant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. 
                # he higher significant 5-bits of the read aging counter sets the priority of the read channel of a given port. Port's priority
                # will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0, the corre
                # ponding port channel will have the highest priority level (timeout condition - Priority0). For multi-port configurations, the
                # aging counters cannot be used to set port priorities when external dynamic priority inputs (arqos) are enabled (timeout is st
                # ll applicable). For single port configurations, the aging counters are only used when they timeout (become 0) to force read-w
                # ite direction switching. In this case, external dynamic priority input, arqos (for reads only) can still be used to set the D
                # RC read priority (2 priority levels: low priority read - LPR, high priority read - HPR) on a command by command basis. Note: 
                # he two LSBs of this register field are tied internally to 2'b00.
                # PSU_DDRC_PCFGR_3_RD_PORT_PRIORITY                                               0xf

                # Port n Configuration Read Register
                #(OFFSET, MASK, VALUE)      (0XFD070614, 0x000073FFU ,0x0000200FU)  */
    mask_write 0XFD070614 0x000073FF 0x0000200F
                # Register : PCFGW_3 @ 0XFD070618</p>

                # If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant
                # d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_
                # imit register.
                # PSU_DDRC_PCFGW_3_WR_PORT_PAGEMATCH_EN                                           0x1

                # If set to 1, enables the AXI urgent sideband signal (awurgent). When enabled and awurgent is asserted by the master, that por
                #  becomes the highest priority and co_gs_go2critical_wr signal to DDRC is asserted if enabled in PCCFG.go2critical_en register
                #  Note that awurgent signal can be asserted anytime and as long as required which is independent of address handshaking (it is
                # not associated with any particular command).
                # PSU_DDRC_PCFGW_3_WR_PORT_URGENT_EN                                              0x1

                # If set to 1, enables aging function for the write channel of the port.
                # PSU_DDRC_PCFGW_3_WR_PORT_AGING_EN                                               0x0

                # Determines the initial load value of write aging counters. These counters will be parallel loaded after reset, or after each 
                # rant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted.
                # The higher significant 5-bits of the write aging counter sets the initial priority of the write channel of a given port. Port
                # s priority will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0
                #  the corresponding port channel will have the highest priority level. For multi-port configurations, the aging counters canno
                #  be used to set port priorities when external dynamic priority inputs (awqos) are enabled (timeout is still applicable). For 
                # ingle port configurations, the aging counters are only used when they timeout (become 0) to force read-write direction switch
                # ng. Note: The two LSBs of this register field are tied internally to 2'b00.
                # PSU_DDRC_PCFGW_3_WR_PORT_PRIORITY                                               0xf

                # Port n Configuration Write Register
                #(OFFSET, MASK, VALUE)      (0XFD070618, 0x000073FFU ,0x0000600FU)  */
    mask_write 0XFD070618 0x000073FF 0x0000600F
                # Register : PCTRL_3 @ 0XFD0706A0</p>

                # Enables port n.
                # PSU_DDRC_PCTRL_3_PORT_EN                                                        0x1

                # Port n Control Register
                #(OFFSET, MASK, VALUE)      (0XFD0706A0, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD0706A0 0x00000001 0x00000001
                # Register : PCFGQOS0_3 @ 0XFD0706A4</p>

                # This bitfield indicates the traffic class of region 1. Valid values are: 0 : LPR, 1: VPR, 2: HPR. For dual address queue conf
                # gurations, region1 maps to the blue address queue. In this case, valid values are 0: LPR and 1: VPR only. When VPR support is
                # disabled (UMCTL2_VPR_EN = 0) and traffic class of region 1 is set to 1 (VPR), VPR traffic is aliased to LPR traffic.
                # PSU_DDRC_PCFGQOS0_3_RQOS_MAP_REGION1                                            0x1

                # This bitfield indicates the traffic class of region 0. Valid values are: 0: LPR, 1: VPR, 2: HPR. For dual address queue confi
                # urations, region 0 maps to the blue address queue. In this case, valid values are: 0: LPR and 1: VPR only. When VPR support i
                #  disabled (UMCTL2_VPR_EN = 0) and traffic class of region0 is set to 1 (VPR), VPR traffic is aliased to LPR traffic.
                # PSU_DDRC_PCFGQOS0_3_RQOS_MAP_REGION0                                            0x0

                # Separation level1 indicating the end of region0 mapping; start of region0 is 0. Possible values for level1 are 0 to 13 (for d
                # al RAQ) or 0 to 14 (for single RAQ) which corresponds to arqos. Note that for PA, arqos values are used directly as port prio
                # ities, where the higher the value corresponds to higher port priority. All of the map_level* registers must be set to distinc
                #  values.
                # PSU_DDRC_PCFGQOS0_3_RQOS_MAP_LEVEL1                                             0x3

                # Port n Read QoS Configuration Register 0
                #(OFFSET, MASK, VALUE)      (0XFD0706A4, 0x0033000FU ,0x00100003U)  */
    mask_write 0XFD0706A4 0x0033000F 0x00100003
                # Register : PCFGQOS1_3 @ 0XFD0706A8</p>

                # Specifies the timeout value for transactions mapped to the red address queue.
                # PSU_DDRC_PCFGQOS1_3_RQOS_MAP_TIMEOUTR                                           0x0

                # Specifies the timeout value for transactions mapped to the blue address queue.
                # PSU_DDRC_PCFGQOS1_3_RQOS_MAP_TIMEOUTB                                           0x4f

                # Port n Read QoS Configuration Register 1
                #(OFFSET, MASK, VALUE)      (0XFD0706A8, 0x07FF07FFU ,0x0000004FU)  */
    mask_write 0XFD0706A8 0x07FF07FF 0x0000004F
                # Register : PCFGWQOS0_3 @ 0XFD0706AC</p>

                # This bitfield indicates the traffic class of region 1. Valid values are: 0: NPW, 1: VPW. When VPW support is disabled (UMCTL2
                # VPW_EN = 0) and traffic class of region 1 is set to 1 (VPW), VPW traffic is aliased to LPW traffic.
                # PSU_DDRC_PCFGWQOS0_3_WQOS_MAP_REGION1                                           0x1

                # This bitfield indicates the traffic class of region 0. Valid values are: 0: NPW, 1: VPW. When VPW support is disabled (UMCTL2
                # VPW_EN = 0) and traffic class of region0 is set to 1 (VPW), VPW traffic is aliased to NPW traffic.
                # PSU_DDRC_PCFGWQOS0_3_WQOS_MAP_REGION0                                           0x0

                # Separation level indicating the end of region0 mapping; start of region0 is 0. Possible values for level1 are 0 to 14 which c
                # rresponds to awqos. Note that for PA, awqos values are used directly as port priorities, where the higher the value correspon
                # s to higher port priority.
                # PSU_DDRC_PCFGWQOS0_3_WQOS_MAP_LEVEL                                             0x3

                # Port n Write QoS Configuration Register 0
                #(OFFSET, MASK, VALUE)      (0XFD0706AC, 0x0033000FU ,0x00100003U)  */
    mask_write 0XFD0706AC 0x0033000F 0x00100003
                # Register : PCFGWQOS1_3 @ 0XFD0706B0</p>

                # Specifies the timeout value for write transactions.
                # PSU_DDRC_PCFGWQOS1_3_WQOS_MAP_TIMEOUT                                           0x4f

                # Port n Write QoS Configuration Register 1
                #(OFFSET, MASK, VALUE)      (0XFD0706B0, 0x000007FFU ,0x0000004FU)  */
    mask_write 0XFD0706B0 0x000007FF 0x0000004F
                # Register : PCFGR_4 @ 0XFD0706C4</p>

                # If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant
                # d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_
                # imit register.
                # PSU_DDRC_PCFGR_4_RD_PORT_PAGEMATCH_EN                                           0x1

                # If set to 1, enables the AXI urgent sideband signal (arurgent). When enabled and arurgent is asserted by the master, that por
                #  becomes the highest priority and co_gs_go2critical_lpr/co_gs_go2critical_hpr signal to DDRC is asserted if enabled in PCCFG.
                # o2critical_en register. Note that arurgent signal can be asserted anytime and as long as required which is independent of add
                # ess handshaking (it is not associated with any particular command).
                # PSU_DDRC_PCFGR_4_RD_PORT_URGENT_EN                                              0x1

                # If set to 1, enables aging function for the read channel of the port.
                # PSU_DDRC_PCFGR_4_RD_PORT_AGING_EN                                               0x0

                # Determines the initial load value of read aging counters. These counters will be parallel loaded after reset, or after each g
                # ant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. 
                # he higher significant 5-bits of the read aging counter sets the priority of the read channel of a given port. Port's priority
                # will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0, the corre
                # ponding port channel will have the highest priority level (timeout condition - Priority0). For multi-port configurations, the
                # aging counters cannot be used to set port priorities when external dynamic priority inputs (arqos) are enabled (timeout is st
                # ll applicable). For single port configurations, the aging counters are only used when they timeout (become 0) to force read-w
                # ite direction switching. In this case, external dynamic priority input, arqos (for reads only) can still be used to set the D
                # RC read priority (2 priority levels: low priority read - LPR, high priority read - HPR) on a command by command basis. Note: 
                # he two LSBs of this register field are tied internally to 2'b00.
                # PSU_DDRC_PCFGR_4_RD_PORT_PRIORITY                                               0xf

                # Port n Configuration Read Register
                #(OFFSET, MASK, VALUE)      (0XFD0706C4, 0x000073FFU ,0x0000600FU)  */
    mask_write 0XFD0706C4 0x000073FF 0x0000600F
                # Register : PCFGW_4 @ 0XFD0706C8</p>

                # If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant
                # d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_
                # imit register.
                # PSU_DDRC_PCFGW_4_WR_PORT_PAGEMATCH_EN                                           0x1

                # If set to 1, enables the AXI urgent sideband signal (awurgent). When enabled and awurgent is asserted by the master, that por
                #  becomes the highest priority and co_gs_go2critical_wr signal to DDRC is asserted if enabled in PCCFG.go2critical_en register
                #  Note that awurgent signal can be asserted anytime and as long as required which is independent of address handshaking (it is
                # not associated with any particular command).
                # PSU_DDRC_PCFGW_4_WR_PORT_URGENT_EN                                              0x1

                # If set to 1, enables aging function for the write channel of the port.
                # PSU_DDRC_PCFGW_4_WR_PORT_AGING_EN                                               0x0

                # Determines the initial load value of write aging counters. These counters will be parallel loaded after reset, or after each 
                # rant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted.
                # The higher significant 5-bits of the write aging counter sets the initial priority of the write channel of a given port. Port
                # s priority will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0
                #  the corresponding port channel will have the highest priority level. For multi-port configurations, the aging counters canno
                #  be used to set port priorities when external dynamic priority inputs (awqos) are enabled (timeout is still applicable). For 
                # ingle port configurations, the aging counters are only used when they timeout (become 0) to force read-write direction switch
                # ng. Note: The two LSBs of this register field are tied internally to 2'b00.
                # PSU_DDRC_PCFGW_4_WR_PORT_PRIORITY                                               0xf

                # Port n Configuration Write Register
                #(OFFSET, MASK, VALUE)      (0XFD0706C8, 0x000073FFU ,0x0000600FU)  */
    mask_write 0XFD0706C8 0x000073FF 0x0000600F
                # Register : PCTRL_4 @ 0XFD070750</p>

                # Enables port n.
                # PSU_DDRC_PCTRL_4_PORT_EN                                                        0x1

                # Port n Control Register
                #(OFFSET, MASK, VALUE)      (0XFD070750, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD070750 0x00000001 0x00000001
                # Register : PCFGQOS0_4 @ 0XFD070754</p>

                # This bitfield indicates the traffic class of region 1. Valid values are: 0 : LPR, 1: VPR, 2: HPR. For dual address queue conf
                # gurations, region1 maps to the blue address queue. In this case, valid values are 0: LPR and 1: VPR only. When VPR support is
                # disabled (UMCTL2_VPR_EN = 0) and traffic class of region 1 is set to 1 (VPR), VPR traffic is aliased to LPR traffic.
                # PSU_DDRC_PCFGQOS0_4_RQOS_MAP_REGION1                                            0x1

                # This bitfield indicates the traffic class of region 0. Valid values are: 0: LPR, 1: VPR, 2: HPR. For dual address queue confi
                # urations, region 0 maps to the blue address queue. In this case, valid values are: 0: LPR and 1: VPR only. When VPR support i
                #  disabled (UMCTL2_VPR_EN = 0) and traffic class of region0 is set to 1 (VPR), VPR traffic is aliased to LPR traffic.
                # PSU_DDRC_PCFGQOS0_4_RQOS_MAP_REGION0                                            0x0

                # Separation level1 indicating the end of region0 mapping; start of region0 is 0. Possible values for level1 are 0 to 13 (for d
                # al RAQ) or 0 to 14 (for single RAQ) which corresponds to arqos. Note that for PA, arqos values are used directly as port prio
                # ities, where the higher the value corresponds to higher port priority. All of the map_level* registers must be set to distinc
                #  values.
                # PSU_DDRC_PCFGQOS0_4_RQOS_MAP_LEVEL1                                             0x3

                # Port n Read QoS Configuration Register 0
                #(OFFSET, MASK, VALUE)      (0XFD070754, 0x0033000FU ,0x00100003U)  */
    mask_write 0XFD070754 0x0033000F 0x00100003
                # Register : PCFGQOS1_4 @ 0XFD070758</p>

                # Specifies the timeout value for transactions mapped to the red address queue.
                # PSU_DDRC_PCFGQOS1_4_RQOS_MAP_TIMEOUTR                                           0x0

                # Specifies the timeout value for transactions mapped to the blue address queue.
                # PSU_DDRC_PCFGQOS1_4_RQOS_MAP_TIMEOUTB                                           0x4f

                # Port n Read QoS Configuration Register 1
                #(OFFSET, MASK, VALUE)      (0XFD070758, 0x07FF07FFU ,0x0000004FU)  */
    mask_write 0XFD070758 0x07FF07FF 0x0000004F
                # Register : PCFGWQOS0_4 @ 0XFD07075C</p>

                # This bitfield indicates the traffic class of region 1. Valid values are: 0: NPW, 1: VPW. When VPW support is disabled (UMCTL2
                # VPW_EN = 0) and traffic class of region 1 is set to 1 (VPW), VPW traffic is aliased to LPW traffic.
                # PSU_DDRC_PCFGWQOS0_4_WQOS_MAP_REGION1                                           0x1

                # This bitfield indicates the traffic class of region 0. Valid values are: 0: NPW, 1: VPW. When VPW support is disabled (UMCTL2
                # VPW_EN = 0) and traffic class of region0 is set to 1 (VPW), VPW traffic is aliased to NPW traffic.
                # PSU_DDRC_PCFGWQOS0_4_WQOS_MAP_REGION0                                           0x0

                # Separation level indicating the end of region0 mapping; start of region0 is 0. Possible values for level1 are 0 to 14 which c
                # rresponds to awqos. Note that for PA, awqos values are used directly as port priorities, where the higher the value correspon
                # s to higher port priority.
                # PSU_DDRC_PCFGWQOS0_4_WQOS_MAP_LEVEL                                             0x3

                # Port n Write QoS Configuration Register 0
                #(OFFSET, MASK, VALUE)      (0XFD07075C, 0x0033000FU ,0x00100003U)  */
    mask_write 0XFD07075C 0x0033000F 0x00100003
                # Register : PCFGWQOS1_4 @ 0XFD070760</p>

                # Specifies the timeout value for write transactions.
                # PSU_DDRC_PCFGWQOS1_4_WQOS_MAP_TIMEOUT                                           0x4f

                # Port n Write QoS Configuration Register 1
                #(OFFSET, MASK, VALUE)      (0XFD070760, 0x000007FFU ,0x0000004FU)  */
    mask_write 0XFD070760 0x000007FF 0x0000004F
                # Register : PCFGR_5 @ 0XFD070774</p>

                # If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant
                # d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_
                # imit register.
                # PSU_DDRC_PCFGR_5_RD_PORT_PAGEMATCH_EN                                           0x0

                # If set to 1, enables the AXI urgent sideband signal (arurgent). When enabled and arurgent is asserted by the master, that por
                #  becomes the highest priority and co_gs_go2critical_lpr/co_gs_go2critical_hpr signal to DDRC is asserted if enabled in PCCFG.
                # o2critical_en register. Note that arurgent signal can be asserted anytime and as long as required which is independent of add
                # ess handshaking (it is not associated with any particular command).
                # PSU_DDRC_PCFGR_5_RD_PORT_URGENT_EN                                              0x1

                # If set to 1, enables aging function for the read channel of the port.
                # PSU_DDRC_PCFGR_5_RD_PORT_AGING_EN                                               0x0

                # Determines the initial load value of read aging counters. These counters will be parallel loaded after reset, or after each g
                # ant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. 
                # he higher significant 5-bits of the read aging counter sets the priority of the read channel of a given port. Port's priority
                # will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0, the corre
                # ponding port channel will have the highest priority level (timeout condition - Priority0). For multi-port configurations, the
                # aging counters cannot be used to set port priorities when external dynamic priority inputs (arqos) are enabled (timeout is st
                # ll applicable). For single port configurations, the aging counters are only used when they timeout (become 0) to force read-w
                # ite direction switching. In this case, external dynamic priority input, arqos (for reads only) can still be used to set the D
                # RC read priority (2 priority levels: low priority read - LPR, high priority read - HPR) on a command by command basis. Note: 
                # he two LSBs of this register field are tied internally to 2'b00.
                # PSU_DDRC_PCFGR_5_RD_PORT_PRIORITY                                               0xf

                # Port n Configuration Read Register
                #(OFFSET, MASK, VALUE)      (0XFD070774, 0x000073FFU ,0x0000200FU)  */
    mask_write 0XFD070774 0x000073FF 0x0000200F
                # Register : PCFGW_5 @ 0XFD070778</p>

                # If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant
                # d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_
                # imit register.
                # PSU_DDRC_PCFGW_5_WR_PORT_PAGEMATCH_EN                                           0x1

                # If set to 1, enables the AXI urgent sideband signal (awurgent). When enabled and awurgent is asserted by the master, that por
                #  becomes the highest priority and co_gs_go2critical_wr signal to DDRC is asserted if enabled in PCCFG.go2critical_en register
                #  Note that awurgent signal can be asserted anytime and as long as required which is independent of address handshaking (it is
                # not associated with any particular command).
                # PSU_DDRC_PCFGW_5_WR_PORT_URGENT_EN                                              0x1

                # If set to 1, enables aging function for the write channel of the port.
                # PSU_DDRC_PCFGW_5_WR_PORT_AGING_EN                                               0x0

                # Determines the initial load value of write aging counters. These counters will be parallel loaded after reset, or after each 
                # rant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted.
                # The higher significant 5-bits of the write aging counter sets the initial priority of the write channel of a given port. Port
                # s priority will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0
                #  the corresponding port channel will have the highest priority level. For multi-port configurations, the aging counters canno
                #  be used to set port priorities when external dynamic priority inputs (awqos) are enabled (timeout is still applicable). For 
                # ingle port configurations, the aging counters are only used when they timeout (become 0) to force read-write direction switch
                # ng. Note: The two LSBs of this register field are tied internally to 2'b00.
                # PSU_DDRC_PCFGW_5_WR_PORT_PRIORITY                                               0xf

                # Port n Configuration Write Register
                #(OFFSET, MASK, VALUE)      (0XFD070778, 0x000073FFU ,0x0000600FU)  */
    mask_write 0XFD070778 0x000073FF 0x0000600F
                # Register : PCTRL_5 @ 0XFD070800</p>

                # Enables port n.
                # PSU_DDRC_PCTRL_5_PORT_EN                                                        0x1

                # Port n Control Register
                #(OFFSET, MASK, VALUE)      (0XFD070800, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD070800 0x00000001 0x00000001
                # Register : PCFGQOS0_5 @ 0XFD070804</p>

                # This bitfield indicates the traffic class of region 1. Valid values are: 0 : LPR, 1: VPR, 2: HPR. For dual address queue conf
                # gurations, region1 maps to the blue address queue. In this case, valid values are 0: LPR and 1: VPR only. When VPR support is
                # disabled (UMCTL2_VPR_EN = 0) and traffic class of region 1 is set to 1 (VPR), VPR traffic is aliased to LPR traffic.
                # PSU_DDRC_PCFGQOS0_5_RQOS_MAP_REGION1                                            0x1

                # This bitfield indicates the traffic class of region 0. Valid values are: 0: LPR, 1: VPR, 2: HPR. For dual address queue confi
                # urations, region 0 maps to the blue address queue. In this case, valid values are: 0: LPR and 1: VPR only. When VPR support i
                #  disabled (UMCTL2_VPR_EN = 0) and traffic class of region0 is set to 1 (VPR), VPR traffic is aliased to LPR traffic.
                # PSU_DDRC_PCFGQOS0_5_RQOS_MAP_REGION0                                            0x0

                # Separation level1 indicating the end of region0 mapping; start of region0 is 0. Possible values for level1 are 0 to 13 (for d
                # al RAQ) or 0 to 14 (for single RAQ) which corresponds to arqos. Note that for PA, arqos values are used directly as port prio
                # ities, where the higher the value corresponds to higher port priority. All of the map_level* registers must be set to distinc
                #  values.
                # PSU_DDRC_PCFGQOS0_5_RQOS_MAP_LEVEL1                                             0x3

                # Port n Read QoS Configuration Register 0
                #(OFFSET, MASK, VALUE)      (0XFD070804, 0x0033000FU ,0x00100003U)  */
    mask_write 0XFD070804 0x0033000F 0x00100003
                # Register : PCFGQOS1_5 @ 0XFD070808</p>

                # Specifies the timeout value for transactions mapped to the red address queue.
                # PSU_DDRC_PCFGQOS1_5_RQOS_MAP_TIMEOUTR                                           0x0

                # Specifies the timeout value for transactions mapped to the blue address queue.
                # PSU_DDRC_PCFGQOS1_5_RQOS_MAP_TIMEOUTB                                           0x4f

                # Port n Read QoS Configuration Register 1
                #(OFFSET, MASK, VALUE)      (0XFD070808, 0x07FF07FFU ,0x0000004FU)  */
    mask_write 0XFD070808 0x07FF07FF 0x0000004F
                # Register : PCFGWQOS0_5 @ 0XFD07080C</p>

                # This bitfield indicates the traffic class of region 1. Valid values are: 0: NPW, 1: VPW. When VPW support is disabled (UMCTL2
                # VPW_EN = 0) and traffic class of region 1 is set to 1 (VPW), VPW traffic is aliased to LPW traffic.
                # PSU_DDRC_PCFGWQOS0_5_WQOS_MAP_REGION1                                           0x1

                # This bitfield indicates the traffic class of region 0. Valid values are: 0: NPW, 1: VPW. When VPW support is disabled (UMCTL2
                # VPW_EN = 0) and traffic class of region0 is set to 1 (VPW), VPW traffic is aliased to NPW traffic.
                # PSU_DDRC_PCFGWQOS0_5_WQOS_MAP_REGION0                                           0x0

                # Separation level indicating the end of region0 mapping; start of region0 is 0. Possible values for level1 are 0 to 14 which c
                # rresponds to awqos. Note that for PA, awqos values are used directly as port priorities, where the higher the value correspon
                # s to higher port priority.
                # PSU_DDRC_PCFGWQOS0_5_WQOS_MAP_LEVEL                                             0x3

                # Port n Write QoS Configuration Register 0
                #(OFFSET, MASK, VALUE)      (0XFD07080C, 0x0033000FU ,0x00100003U)  */
    mask_write 0XFD07080C 0x0033000F 0x00100003
                # Register : PCFGWQOS1_5 @ 0XFD070810</p>

                # Specifies the timeout value for write transactions.
                # PSU_DDRC_PCFGWQOS1_5_WQOS_MAP_TIMEOUT                                           0x4f

                # Port n Write QoS Configuration Register 1
                #(OFFSET, MASK, VALUE)      (0XFD070810, 0x000007FFU ,0x0000004FU)  */
    mask_write 0XFD070810 0x000007FF 0x0000004F
                # Register : SARBASE0 @ 0XFD070F04</p>

                # Base address for address region n specified as awaddr[UMCTL2_A_ADDRW-1:x] and araddr[UMCTL2_A_ADDRW-1:x] where x is determine
                #  by the minimum block size parameter UMCTL2_SARMINSIZE: (x=log2(block size)).
                # PSU_DDRC_SARBASE0_BASE_ADDR                                                     0x0

                # SAR Base Address Register n
                #(OFFSET, MASK, VALUE)      (0XFD070F04, 0x000001FFU ,0x00000000U)  */
    mask_write 0XFD070F04 0x000001FF 0x00000000
                # Register : SARSIZE0 @ 0XFD070F08</p>

                # Number of blocks for address region n. This register determines the total size of the region in multiples of minimum block si
                # e as specified by the hardware parameter UMCTL2_SARMINSIZE. The register value is encoded as number of blocks = nblocks + 1. 
                # or example, if register is programmed to 0, region will have 1 block.
                # PSU_DDRC_SARSIZE0_NBLOCKS                                                       0x0

                # SAR Size Register n
                #(OFFSET, MASK, VALUE)      (0XFD070F08, 0x000000FFU ,0x00000000U)  */
    mask_write 0XFD070F08 0x000000FF 0x00000000
                # Register : SARBASE1 @ 0XFD070F0C</p>

                # Base address for address region n specified as awaddr[UMCTL2_A_ADDRW-1:x] and araddr[UMCTL2_A_ADDRW-1:x] where x is determine
                #  by the minimum block size parameter UMCTL2_SARMINSIZE: (x=log2(block size)).
                # PSU_DDRC_SARBASE1_BASE_ADDR                                                     0x10

                # SAR Base Address Register n
                #(OFFSET, MASK, VALUE)      (0XFD070F0C, 0x000001FFU ,0x00000010U)  */
    mask_write 0XFD070F0C 0x000001FF 0x00000010
                # Register : SARSIZE1 @ 0XFD070F10</p>

                # Number of blocks for address region n. This register determines the total size of the region in multiples of minimum block si
                # e as specified by the hardware parameter UMCTL2_SARMINSIZE. The register value is encoded as number of blocks = nblocks + 1. 
                # or example, if register is programmed to 0, region will have 1 block.
                # PSU_DDRC_SARSIZE1_NBLOCKS                                                       0xf

                # SAR Size Register n
                #(OFFSET, MASK, VALUE)      (0XFD070F10, 0x000000FFU ,0x0000000FU)  */
    mask_write 0XFD070F10 0x000000FF 0x0000000F
                # Register : DFITMG0_SHADOW @ 0XFD072190</p>

                # Specifies the number of DFI clock cycles after an assertion or de-assertion of the DFI control signals that the control signa
                # s at the PHY-DRAM interface reflect the assertion or de-assertion. If the DFI clock and the memory clock are not phase-aligne
                # , this timing parameter should be rounded up to the next integer value. Note that if using RDIMM, it is necessary to incremen
                #  this parameter by RDIMM's extra cycle of latency in terms of DFI clock.
                # PSU_DDRC_DFITMG0_SHADOW_DFI_T_CTRL_DELAY                                        0x7

                # Defines whether dfi_rddata_en/dfi_rddata/dfi_rddata_valid is generated using HDR or SDR values Selects whether value in DFITM
                # 0.dfi_t_rddata_en is in terms of SDR or HDR clock cycles: - 0 in terms of HDR clock cycles - 1 in terms of SDR clock cycles R
                # fer to PHY specification for correct value.
                # PSU_DDRC_DFITMG0_SHADOW_DFI_RDDATA_USE_SDR                                      0x1

                # Time from the assertion of a read command on the DFI interface to the assertion of the dfi_rddata_en signal. Refer to PHY spe
                # ification for correct value. This corresponds to the DFI parameter trddata_en. Note that, depending on the PHY, if using RDIM
                # , it may be necessary to use the value (CL + 1) in the calculation of trddata_en. This is to compensate for the extra cycle o
                #  latency through the RDIMM. Unit: Clocks
                # PSU_DDRC_DFITMG0_SHADOW_DFI_T_RDDATA_EN                                         0x2

                # Defines whether dfi_wrdata_en/dfi_wrdata/dfi_wrdata_mask is generated using HDR or SDR values Selects whether value in DFITMG
                # .dfi_tphy_wrlat is in terms of SDR or HDR clock cycles Selects whether value in DFITMG0.dfi_tphy_wrdata is in terms of SDR or
                # HDR clock cycles - 0 in terms of HDR clock cycles - 1 in terms of SDR clock cycles Refer to PHY specification for correct val
                # e.
                # PSU_DDRC_DFITMG0_SHADOW_DFI_WRDATA_USE_SDR                                      0x1

                # Specifies the number of clock cycles between when dfi_wrdata_en is asserted to when the associated write data is driven on th
                #  dfi_wrdata signal. This corresponds to the DFI timing parameter tphy_wrdata. Refer to PHY specification for correct value. N
                # te, max supported value is 8. Unit: Clocks
                # PSU_DDRC_DFITMG0_SHADOW_DFI_TPHY_WRDATA                                         0x0

                # Write latency Number of clocks from the write command to write data enable (dfi_wrdata_en). This corresponds to the DFI timin
                #  parameter tphy_wrlat. Refer to PHY specification for correct value.Note that, depending on the PHY, if using RDIMM, it may b
                #  necessary to use the value (CL + 1) in the calculation of tphy_wrlat. This is to compensate for the extra cycle of latency t
                # rough the RDIMM.
                # PSU_DDRC_DFITMG0_SHADOW_DFI_TPHY_WRLAT                                          0x2

                # DFI Timing Shadow Register 0
                #(OFFSET, MASK, VALUE)      (0XFD072190, 0x1FBFBF3FU ,0x07828002U)  */
    mask_write 0XFD072190 0x1FBFBF3F 0x07828002
                # : DDR CONTROLLER RESET
                # Register : RST_DDR_SS @ 0XFD1A0108</p>

                # DDR block level reset inside of the DDR Sub System
                # PSU_CRF_APB_RST_DDR_SS_DDR_RESET                                                0X0

                # DDR sub system block level reset
                #(OFFSET, MASK, VALUE)      (0XFD1A0108, 0x00000008U ,0x00000000U)  */
    mask_write 0XFD1A0108 0x00000008 0x00000000
                # : DDR PHY
                # Register : PGCR0 @ 0XFD080010</p>

                # Address Copy
                # PSU_DDR_PHY_PGCR0_ADCP                                                          0x0

                # Reserved. Returns zeroes on reads.
                # PSU_DDR_PHY_PGCR0_RESERVED_30_27                                                0x0

                # PHY FIFO Reset
                # PSU_DDR_PHY_PGCR0_PHYFRST                                                       0x1

                # Oscillator Mode Address/Command Delay Line Select
                # PSU_DDR_PHY_PGCR0_OSCACDL                                                       0x3

                # Reserved. Returns zeroes on reads.
                # PSU_DDR_PHY_PGCR0_RESERVED_23_19                                                0x0

                # Digital Test Output Select
                # PSU_DDR_PHY_PGCR0_DTOSEL                                                        0x0

                # Reserved. Returns zeroes on reads.
                # PSU_DDR_PHY_PGCR0_RESERVED_13                                                   0x0

                # Oscillator Mode Division
                # PSU_DDR_PHY_PGCR0_OSCDIV                                                        0xf

                # Oscillator Enable
                # PSU_DDR_PHY_PGCR0_OSCEN                                                         0x0

                # Reserved. Returns zeroes on reads.
                # PSU_DDR_PHY_PGCR0_RESERVED_7_0                                                  0x0

                # PHY General Configuration Register 0
                #(OFFSET, MASK, VALUE)      (0XFD080010, 0xFFFFFFFFU ,0x07001E00U)  */
    mask_write 0XFD080010 0xFFFFFFFF 0x07001E00
                # Register : PGCR2 @ 0XFD080018</p>

                # Clear Training Status Registers
                # PSU_DDR_PHY_PGCR2_CLRTSTAT                                                      0x0

                # Clear Impedance Calibration
                # PSU_DDR_PHY_PGCR2_CLRZCAL                                                       0x0

                # Clear Parity Error
                # PSU_DDR_PHY_PGCR2_CLRPERR                                                       0x0

                # Initialization Complete Pin Configuration
                # PSU_DDR_PHY_PGCR2_ICPC                                                          0x0

                # Data Training PUB Mode Exit Timer
                # PSU_DDR_PHY_PGCR2_DTPMXTMR                                                      0xf

                # Initialization Bypass
                # PSU_DDR_PHY_PGCR2_INITFSMBYP                                                    0x0

                # PLL FSM Bypass
                # PSU_DDR_PHY_PGCR2_PLLFSMBYP                                                     0x0

                # Refresh Period
                # PSU_DDR_PHY_PGCR2_TREFPRD                                                       0x12302

                # PHY General Configuration Register 2
                #(OFFSET, MASK, VALUE)      (0XFD080018, 0xFFFFFFFFU ,0x00F12302U)  */
    mask_write 0XFD080018 0xFFFFFFFF 0x00F12302
                # Register : PGCR5 @ 0XFD080024</p>

                # Frequency B Ratio Term
                # PSU_DDR_PHY_PGCR5_FRQBT                                                         0x1

                # Frequency A Ratio Term
                # PSU_DDR_PHY_PGCR5_FRQAT                                                         0x1

                # DFI Disconnect Time Period
                # PSU_DDR_PHY_PGCR5_DISCNPERIOD                                                   0x0

                # Receiver bias core side control
                # PSU_DDR_PHY_PGCR5_VREF_RBCTRL                                                   0xf

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_PGCR5_RESERVED_3                                                    0x0

                # Internal VREF generator REFSEL ragne select
                # PSU_DDR_PHY_PGCR5_DXREFISELRANGE                                                0x1

                # DDL Page Read Write select
                # PSU_DDR_PHY_PGCR5_DDLPGACT                                                      0x0

                # DDL Page Read Write select
                # PSU_DDR_PHY_PGCR5_DDLPGRW                                                       0x0

                # PHY General Configuration Register 5
                #(OFFSET, MASK, VALUE)      (0XFD080024, 0xFFFFFFFFU ,0x010100F4U)  */
    mask_write 0XFD080024 0xFFFFFFFF 0x010100F4
                # Register : PTR0 @ 0XFD080040</p>

                # PLL Power-Down Time
                # PSU_DDR_PHY_PTR0_TPLLPD                                                         0x2f0

                # PLL Gear Shift Time
                # PSU_DDR_PHY_PTR0_TPLLGS                                                         0x60

                # PHY Reset Time
                # PSU_DDR_PHY_PTR0_TPHYRST                                                        0x10

                # PHY Timing Register 0
                #(OFFSET, MASK, VALUE)      (0XFD080040, 0xFFFFFFFFU ,0x5E001810U)  */
    mask_write 0XFD080040 0xFFFFFFFF 0x5E001810
                # Register : PTR1 @ 0XFD080044</p>

                # PLL Lock Time
                # PSU_DDR_PHY_PTR1_TPLLLOCK                                                       0x80

                # Reserved. Returns zeroes on reads.
                # PSU_DDR_PHY_PTR1_RESERVED_15_13                                                 0x0

                # PLL Reset Time
                # PSU_DDR_PHY_PTR1_TPLLRST                                                        0x5f0

                # PHY Timing Register 1
                #(OFFSET, MASK, VALUE)      (0XFD080044, 0xFFFFFFFFU ,0x008005F0U)  */
    mask_write 0XFD080044 0xFFFFFFFF 0x008005F0
                # Register : DSGCR @ 0XFD080090</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DSGCR_RESERVED_31_28                                                0x0

                # When RDBI enabled, this bit is used to select RDBI CL calculation, if it is 1b1, calculation will use RDBICL, otherwise use d
                # fault calculation.
                # PSU_DDR_PHY_DSGCR_RDBICLSEL                                                     0x0

                # When RDBI enabled, if RDBICLSEL is asserted, RDBI CL adjust using this value.
                # PSU_DDR_PHY_DSGCR_RDBICL                                                        0x2

                # PHY Impedance Update Enable
                # PSU_DDR_PHY_DSGCR_PHYZUEN                                                       0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DSGCR_RESERVED_22                                                   0x0

                # SDRAM Reset Output Enable
                # PSU_DDR_PHY_DSGCR_RSTOE                                                         0x1

                # Single Data Rate Mode
                # PSU_DDR_PHY_DSGCR_SDRMODE                                                       0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DSGCR_RESERVED_18                                                   0x0

                # ATO Analog Test Enable
                # PSU_DDR_PHY_DSGCR_ATOAE                                                         0x0

                # DTO Output Enable
                # PSU_DDR_PHY_DSGCR_DTOOE                                                         0x0

                # DTO I/O Mode
                # PSU_DDR_PHY_DSGCR_DTOIOM                                                        0x0

                # DTO Power Down Receiver
                # PSU_DDR_PHY_DSGCR_DTOPDR                                                        0x1

                # Reserved. Return zeroes on reads
                # PSU_DDR_PHY_DSGCR_RESERVED_13                                                   0x0

                # DTO On-Die Termination
                # PSU_DDR_PHY_DSGCR_DTOODT                                                        0x0

                # PHY Update Acknowledge Delay
                # PSU_DDR_PHY_DSGCR_PUAD                                                          0x4

                # Controller Update Acknowledge Enable
                # PSU_DDR_PHY_DSGCR_CUAEN                                                         0x1

                # Reserved. Return zeroes on reads
                # PSU_DDR_PHY_DSGCR_RESERVED_4_3                                                  0x0

                # Controller Impedance Update Enable
                # PSU_DDR_PHY_DSGCR_CTLZUEN                                                       0x0

                # Reserved. Return zeroes on reads
                # PSU_DDR_PHY_DSGCR_RESERVED_1                                                    0x0

                # PHY Update Request Enable
                # PSU_DDR_PHY_DSGCR_PUREN                                                         0x1

                # DDR System General Configuration Register
                #(OFFSET, MASK, VALUE)      (0XFD080090, 0xFFFFFFFFU ,0x02A04121U)  */
    mask_write 0XFD080090 0xFFFFFFFF 0x02A04121
                # Register : DCR @ 0XFD080100</p>

                # DDR4 Gear Down Timing.
                # PSU_DDR_PHY_DCR_GEARDN                                                          0x0

                # Un-used Bank Group
                # PSU_DDR_PHY_DCR_UBG                                                             0x0

                # Un-buffered DIMM Address Mirroring
                # PSU_DDR_PHY_DCR_UDIMM                                                           0x0

                # DDR 2T Timing
                # PSU_DDR_PHY_DCR_DDR2T                                                           0x0

                # No Simultaneous Rank Access
                # PSU_DDR_PHY_DCR_NOSRA                                                           0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DCR_RESERVED_26_18                                                  0x0

                # Byte Mask
                # PSU_DDR_PHY_DCR_BYTEMASK                                                        0x1

                # DDR Type
                # PSU_DDR_PHY_DCR_DDRTYPE                                                         0x0

                # Multi-Purpose Register (MPR) DQ (DDR3 Only)
                # PSU_DDR_PHY_DCR_MPRDQ                                                           0x0

                # Primary DQ (DDR3 Only)
                # PSU_DDR_PHY_DCR_PDQ                                                             0x0

                # DDR 8-Bank
                # PSU_DDR_PHY_DCR_DDR8BNK                                                         0x1

                # DDR Mode
                # PSU_DDR_PHY_DCR_DDRMD                                                           0x4

                # DRAM Configuration Register
                #(OFFSET, MASK, VALUE)      (0XFD080100, 0xFFFFFFFFU ,0x0800040CU)  */
    mask_write 0XFD080100 0xFFFFFFFF 0x0800040C
                # Register : DTPR0 @ 0XFD080110</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTPR0_RESERVED_31_29                                                0x0

                # Activate to activate command delay (different banks)
                # PSU_DDR_PHY_DTPR0_TRRD                                                          0x6

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTPR0_RESERVED_23                                                   0x0

                # Activate to precharge command delay
                # PSU_DDR_PHY_DTPR0_TRAS                                                          0x24

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTPR0_RESERVED_15                                                   0x0

                # Precharge command period
                # PSU_DDR_PHY_DTPR0_TRP                                                           0x12

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTPR0_RESERVED_7_5                                                  0x0

                # Internal read to precharge command delay
                # PSU_DDR_PHY_DTPR0_TRTP                                                          0x8

                # DRAM Timing Parameters Register 0
                #(OFFSET, MASK, VALUE)      (0XFD080110, 0xFFFFFFFFU ,0x06241208U)  */
    mask_write 0XFD080110 0xFFFFFFFF 0x06241208
                # Register : DTPR1 @ 0XFD080114</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTPR1_RESERVED_31                                                   0x0

                # Minimum delay from when write leveling mode is programmed to the first DQS/DQS# rising edge.
                # PSU_DDR_PHY_DTPR1_TWLMRD                                                        0x28

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTPR1_RESERVED_23                                                   0x0

                # 4-bank activate period
                # PSU_DDR_PHY_DTPR1_TFAW                                                          0x18

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTPR1_RESERVED_15_11                                                0x0

                # Load mode update delay (DDR4 and DDR3 only)
                # PSU_DDR_PHY_DTPR1_TMOD                                                          0x7

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTPR1_RESERVED_7_5                                                  0x0

                # Load mode cycle time
                # PSU_DDR_PHY_DTPR1_TMRD                                                          0x8

                # DRAM Timing Parameters Register 1
                #(OFFSET, MASK, VALUE)      (0XFD080114, 0xFFFFFFFFU ,0x28180708U)  */
    mask_write 0XFD080114 0xFFFFFFFF 0x28180708
                # Register : DTPR2 @ 0XFD080118</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTPR2_RESERVED_31_29                                                0x0

                # Read to Write command delay. Valid values are
                # PSU_DDR_PHY_DTPR2_TRTW                                                          0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTPR2_RESERVED_27_25                                                0x0

                # Read to ODT delay (DDR3 only)
                # PSU_DDR_PHY_DTPR2_TRTODT                                                        0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTPR2_RESERVED_23_20                                                0x0

                # CKE minimum pulse width
                # PSU_DDR_PHY_DTPR2_TCKE                                                          0x8

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTPR2_RESERVED_15_10                                                0x0

                # Self refresh exit delay
                # PSU_DDR_PHY_DTPR2_TXS                                                           0x200

                # DRAM Timing Parameters Register 2
                #(OFFSET, MASK, VALUE)      (0XFD080118, 0xFFFFFFFFU ,0x00080200U)  */
    mask_write 0XFD080118 0xFFFFFFFF 0x00080200
                # Register : DTPR3 @ 0XFD08011C</p>

                # ODT turn-off delay extension
                # PSU_DDR_PHY_DTPR3_TOFDX                                                         0x4

                # Read to read and write to write command delay
                # PSU_DDR_PHY_DTPR3_TCCD                                                          0x0

                # DLL locking time
                # PSU_DDR_PHY_DTPR3_TDLLK                                                         0x300

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTPR3_RESERVED_15_12                                                0x0

                # Maximum DQS output access time from CK/CK# (LPDDR2/3 only)
                # PSU_DDR_PHY_DTPR3_TDQSCKMAX                                                     0x8

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTPR3_RESERVED_7_3                                                  0x0

                # DQS output access time from CK/CK# (LPDDR2/3 only)
                # PSU_DDR_PHY_DTPR3_TDQSCK                                                        0x4

                # DRAM Timing Parameters Register 3
                #(OFFSET, MASK, VALUE)      (0XFD08011C, 0xFFFFFFFFU ,0x83000804U)  */
    mask_write 0XFD08011C 0xFFFFFFFF 0x83000804
                # Register : DTPR4 @ 0XFD080120</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTPR4_RESERVED_31_30                                                0x0

                # ODT turn-on/turn-off delays (DDR2 only)
                # PSU_DDR_PHY_DTPR4_TAOND_TAOFD                                                   0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTPR4_RESERVED_27_26                                                0x0

                # Refresh-to-Refresh
                # PSU_DDR_PHY_DTPR4_TRFC                                                          0x116

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTPR4_RESERVED_15_14                                                0x0

                # Write leveling output delay
                # PSU_DDR_PHY_DTPR4_TWLO                                                          0x2b

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTPR4_RESERVED_7_5                                                  0x0

                # Power down exit delay
                # PSU_DDR_PHY_DTPR4_TXP                                                           0x8

                # DRAM Timing Parameters Register 4
                #(OFFSET, MASK, VALUE)      (0XFD080120, 0xFFFFFFFFU ,0x01162B08U)  */
    mask_write 0XFD080120 0xFFFFFFFF 0x01162B08
                # Register : DTPR5 @ 0XFD080124</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTPR5_RESERVED_31_24                                                0x0

                # Activate to activate command delay (same bank)
                # PSU_DDR_PHY_DTPR5_TRC                                                           0x32

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTPR5_RESERVED_15                                                   0x0

                # Activate to read or write delay
                # PSU_DDR_PHY_DTPR5_TRCD                                                          0xf

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTPR5_RESERVED_7_5                                                  0x0

                # Internal write to read command delay
                # PSU_DDR_PHY_DTPR5_TWTR                                                          0x9

                # DRAM Timing Parameters Register 5
                #(OFFSET, MASK, VALUE)      (0XFD080124, 0xFFFFFFFFU ,0x00320F09U)  */
    mask_write 0XFD080124 0xFFFFFFFF 0x00320F09
                # Register : DTPR6 @ 0XFD080128</p>

                # PUB Write Latency Enable
                # PSU_DDR_PHY_DTPR6_PUBWLEN                                                       0x0

                # PUB Read Latency Enable
                # PSU_DDR_PHY_DTPR6_PUBRLEN                                                       0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTPR6_RESERVED_29_14                                                0x0

                # Write Latency
                # PSU_DDR_PHY_DTPR6_PUBWL                                                         0xe

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTPR6_RESERVED_7_6                                                  0x0

                # Read Latency
                # PSU_DDR_PHY_DTPR6_PUBRL                                                         0xf

                # DRAM Timing Parameters Register 6
                #(OFFSET, MASK, VALUE)      (0XFD080128, 0xFFFFFFFFU ,0x00000E0FU)  */
    mask_write 0XFD080128 0xFFFFFFFF 0x00000E0F
                # Register : RDIMMGCR0 @ 0XFD080140</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_RDIMMGCR0_RESERVED_31                                               0x0

                # RDMIMM Quad CS Enable
                # PSU_DDR_PHY_RDIMMGCR0_QCSEN                                                     0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_RDIMMGCR0_RESERVED_29_28                                            0x0

                # RDIMM Outputs I/O Mode
                # PSU_DDR_PHY_RDIMMGCR0_RDIMMIOM                                                  0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_RDIMMGCR0_RESERVED_26_24                                            0x0

                # ERROUT# Output Enable
                # PSU_DDR_PHY_RDIMMGCR0_ERROUTOE                                                  0x0

                # ERROUT# I/O Mode
                # PSU_DDR_PHY_RDIMMGCR0_ERROUTIOM                                                 0x1

                # ERROUT# Power Down Receiver
                # PSU_DDR_PHY_RDIMMGCR0_ERROUTPDR                                                 0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_RDIMMGCR0_RESERVED_20                                               0x0

                # ERROUT# On-Die Termination
                # PSU_DDR_PHY_RDIMMGCR0_ERROUTODT                                                 0x0

                # Load Reduced DIMM
                # PSU_DDR_PHY_RDIMMGCR0_LRDIMM                                                    0x0

                # PAR_IN I/O Mode
                # PSU_DDR_PHY_RDIMMGCR0_PARINIOM                                                  0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_RDIMMGCR0_RESERVED_16_8                                             0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_RDIMMGCR0_RNKMRREN_RSVD                                             0x0

                # Rank Mirror Enable.
                # PSU_DDR_PHY_RDIMMGCR0_RNKMRREN                                                  0x2

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_RDIMMGCR0_RESERVED_3                                                0x0

                # Stop on Parity Error
                # PSU_DDR_PHY_RDIMMGCR0_SOPERR                                                    0x0

                # Parity Error No Registering
                # PSU_DDR_PHY_RDIMMGCR0_ERRNOREG                                                  0x0

                # Registered DIMM
                # PSU_DDR_PHY_RDIMMGCR0_RDIMM                                                     0x0

                # RDIMM General Configuration Register 0
                #(OFFSET, MASK, VALUE)      (0XFD080140, 0xFFFFFFFFU ,0x08400020U)  */
    mask_write 0XFD080140 0xFFFFFFFF 0x08400020
                # Register : RDIMMGCR1 @ 0XFD080144</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_RDIMMGCR1_RESERVED_31_29                                            0x0

                # Address [17] B-side Inversion Disable
                # PSU_DDR_PHY_RDIMMGCR1_A17BID                                                    0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_RDIMMGCR1_RESERVED_27                                               0x0

                # Command word to command word programming delay
                # PSU_DDR_PHY_RDIMMGCR1_TBCMRD_L2                                                 0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_RDIMMGCR1_RESERVED_23                                               0x0

                # Command word to command word programming delay
                # PSU_DDR_PHY_RDIMMGCR1_TBCMRD_L                                                  0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_RDIMMGCR1_RESERVED_19                                               0x0

                # Command word to command word programming delay
                # PSU_DDR_PHY_RDIMMGCR1_TBCMRD                                                    0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_RDIMMGCR1_RESERVED_15_14                                            0x0

                # Stabilization time
                # PSU_DDR_PHY_RDIMMGCR1_TBCSTAB                                                   0xc80

                # RDIMM General Configuration Register 1
                #(OFFSET, MASK, VALUE)      (0XFD080144, 0xFFFFFFFFU ,0x00000C80U)  */
    mask_write 0XFD080144 0xFFFFFFFF 0x00000C80
                # Register : RDIMMCR1 @ 0XFD080154</p>

                # Control Word 15
                # PSU_DDR_PHY_RDIMMCR1_RC15                                                       0x0

                # DDR4 Control Word 14 (Parity Control Word) / DDR3 Reserved
                # PSU_DDR_PHY_RDIMMCR1_RC14                                                       0x0

                # DDR4 Control Word 13 (DIMM Configuration Control Word) / DDR3 Reserved
                # PSU_DDR_PHY_RDIMMCR1_RC13                                                       0x0

                # DDR4 Control Word 12 (Training Control Word) / DDR3 Reserved
                # PSU_DDR_PHY_RDIMMCR1_RC12                                                       0x0

                # DDR4 Control Word 11 (Operating Voltage VDD and VREFCA Source Control Word) / DDR3 Control Word 11 (Operation Voltage VDD Con
                # rol Word)
                # PSU_DDR_PHY_RDIMMCR1_RC11                                                       0x0

                # DDR4/DDR3 Control Word 10 (RDIMM Operating Speed Control Word)
                # PSU_DDR_PHY_RDIMMCR1_RC10                                                       0x2

                # DDR4/DDR3 Control Word 9 (Power Saving Settings Control Word)
                # PSU_DDR_PHY_RDIMMCR1_RC9                                                        0x0

                # DDR4 Control Word 8 (Input/Output Configuration Control Word) / DDR3 Control Word 8 (Additional Input Bus Termination Setting
                # Control Word)
                # PSU_DDR_PHY_RDIMMCR1_RC8                                                        0x0

                # RDIMM Control Register 1
                #(OFFSET, MASK, VALUE)      (0XFD080154, 0xFFFFFFFFU ,0x00000200U)  */
    mask_write 0XFD080154 0xFFFFFFFF 0x00000200
                # Register : MR0 @ 0XFD080180</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_MR0_RESERVED_31_8                                                   0x8

                # CA Terminating Rank
                # PSU_DDR_PHY_MR0_CATR                                                            0x0

                # Reserved. These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0.
                # PSU_DDR_PHY_MR0_RSVD_6_5                                                        0x1

                # Built-in Self-Test for RZQ
                # PSU_DDR_PHY_MR0_RZQI                                                            0x2

                # Reserved. These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0.
                # PSU_DDR_PHY_MR0_RSVD_2_0                                                        0x0

                # LPDDR4 Mode Register 0
                #(OFFSET, MASK, VALUE)      (0XFD080180, 0xFFFFFFFFU ,0x00000830U)  */
    mask_write 0XFD080180 0xFFFFFFFF 0x00000830
                # Register : MR1 @ 0XFD080184</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_MR1_RESERVED_31_8                                                   0x3

                # Read Postamble Length
                # PSU_DDR_PHY_MR1_RDPST                                                           0x0

                # Write-recovery for auto-precharge command
                # PSU_DDR_PHY_MR1_NWR                                                             0x0

                # Read Preamble Length
                # PSU_DDR_PHY_MR1_RDPRE                                                           0x0

                # Write Preamble Length
                # PSU_DDR_PHY_MR1_WRPRE                                                           0x0

                # Burst Length
                # PSU_DDR_PHY_MR1_BL                                                              0x1

                # LPDDR4 Mode Register 1
                #(OFFSET, MASK, VALUE)      (0XFD080184, 0xFFFFFFFFU ,0x00000301U)  */
    mask_write 0XFD080184 0xFFFFFFFF 0x00000301
                # Register : MR2 @ 0XFD080188</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_MR2_RESERVED_31_8                                                   0x0

                # Write Leveling
                # PSU_DDR_PHY_MR2_WRL                                                             0x0

                # Write Latency Set
                # PSU_DDR_PHY_MR2_WLS                                                             0x0

                # Write Latency
                # PSU_DDR_PHY_MR2_WL                                                              0x4

                # Read Latency
                # PSU_DDR_PHY_MR2_RL                                                              0x0

                # LPDDR4 Mode Register 2
                #(OFFSET, MASK, VALUE)      (0XFD080188, 0xFFFFFFFFU ,0x00000020U)  */
    mask_write 0XFD080188 0xFFFFFFFF 0x00000020
                # Register : MR3 @ 0XFD08018C</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_MR3_RESERVED_31_8                                                   0x2

                # DBI-Write Enable
                # PSU_DDR_PHY_MR3_DBIWR                                                           0x0

                # DBI-Read Enable
                # PSU_DDR_PHY_MR3_DBIRD                                                           0x0

                # Pull-down Drive Strength
                # PSU_DDR_PHY_MR3_PDDS                                                            0x0

                # These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0.
                # PSU_DDR_PHY_MR3_RSVD                                                            0x0

                # Write Postamble Length
                # PSU_DDR_PHY_MR3_WRPST                                                           0x0

                # Pull-up Calibration Point
                # PSU_DDR_PHY_MR3_PUCAL                                                           0x0

                # LPDDR4 Mode Register 3
                #(OFFSET, MASK, VALUE)      (0XFD08018C, 0xFFFFFFFFU ,0x00000200U)  */
    mask_write 0XFD08018C 0xFFFFFFFF 0x00000200
                # Register : MR4 @ 0XFD080190</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_MR4_RESERVED_31_16                                                  0x0

                # These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0.
                # PSU_DDR_PHY_MR4_RSVD_15_13                                                      0x0

                # Write Preamble
                # PSU_DDR_PHY_MR4_WRP                                                             0x0

                # Read Preamble
                # PSU_DDR_PHY_MR4_RDP                                                             0x0

                # Read Preamble Training Mode
                # PSU_DDR_PHY_MR4_RPTM                                                            0x0

                # Self Refresh Abort
                # PSU_DDR_PHY_MR4_SRA                                                             0x0

                # CS to Command Latency Mode
                # PSU_DDR_PHY_MR4_CS2CMDL                                                         0x0

                # These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0.
                # PSU_DDR_PHY_MR4_RSVD1                                                           0x0

                # Internal VREF Monitor
                # PSU_DDR_PHY_MR4_IVM                                                             0x0

                # Temperature Controlled Refresh Mode
                # PSU_DDR_PHY_MR4_TCRM                                                            0x0

                # Temperature Controlled Refresh Range
                # PSU_DDR_PHY_MR4_TCRR                                                            0x0

                # Maximum Power Down Mode
                # PSU_DDR_PHY_MR4_MPDM                                                            0x0

                # This is a JEDEC reserved bit and is recommended by JEDEC to be programmed to 0x0.
                # PSU_DDR_PHY_MR4_RSVD_0                                                          0x0

                # DDR4 Mode Register 4
                #(OFFSET, MASK, VALUE)      (0XFD080190, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD080190 0xFFFFFFFF 0x00000000
                # Register : MR5 @ 0XFD080194</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_MR5_RESERVED_31_16                                                  0x0

                # These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0.
                # PSU_DDR_PHY_MR5_RSVD                                                            0x0

                # Read DBI
                # PSU_DDR_PHY_MR5_RDBI                                                            0x0

                # Write DBI
                # PSU_DDR_PHY_MR5_WDBI                                                            0x0

                # Data Mask
                # PSU_DDR_PHY_MR5_DM                                                              0x1

                # CA Parity Persistent Error
                # PSU_DDR_PHY_MR5_CAPPE                                                           0x1

                # RTT_PARK
                # PSU_DDR_PHY_MR5_RTTPARK                                                         0x3

                # ODT Input Buffer during Power Down mode
                # PSU_DDR_PHY_MR5_ODTIBPD                                                         0x0

                # C/A Parity Error Status
                # PSU_DDR_PHY_MR5_CAPES                                                           0x0

                # CRC Error Clear
                # PSU_DDR_PHY_MR5_CRCEC                                                           0x0

                # C/A Parity Latency Mode
                # PSU_DDR_PHY_MR5_CAPM                                                            0x0

                # DDR4 Mode Register 5
                #(OFFSET, MASK, VALUE)      (0XFD080194, 0xFFFFFFFFU ,0x000006C0U)  */
    mask_write 0XFD080194 0xFFFFFFFF 0x000006C0
                # Register : MR6 @ 0XFD080198</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_MR6_RESERVED_31_16                                                  0x0

                # These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0.
                # PSU_DDR_PHY_MR6_RSVD_15_13                                                      0x0

                # CAS_n to CAS_n command delay for same bank group (tCCD_L)
                # PSU_DDR_PHY_MR6_TCCDL                                                           0x2

                # These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0.
                # PSU_DDR_PHY_MR6_RSVD_9_8                                                        0x0

                # VrefDQ Training Enable
                # PSU_DDR_PHY_MR6_VDDQTEN                                                         0x0

                # VrefDQ Training Range
                # PSU_DDR_PHY_MR6_VDQTRG                                                          0x0

                # VrefDQ Training Values
                # PSU_DDR_PHY_MR6_VDQTVAL                                                         0x19

                # DDR4 Mode Register 6
                #(OFFSET, MASK, VALUE)      (0XFD080198, 0xFFFFFFFFU ,0x00000819U)  */
    mask_write 0XFD080198 0xFFFFFFFF 0x00000819
                # Register : MR11 @ 0XFD0801AC</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_MR11_RESERVED_31_8                                                  0x0

                # These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0.
                # PSU_DDR_PHY_MR11_RSVD                                                           0x0

                # Power Down Control
                # PSU_DDR_PHY_MR11_PDCTL                                                          0x0

                # DQ Bus Receiver On-Die-Termination
                # PSU_DDR_PHY_MR11_DQODT                                                          0x0

                # LPDDR4 Mode Register 11
                #(OFFSET, MASK, VALUE)      (0XFD0801AC, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD0801AC 0xFFFFFFFF 0x00000000
                # Register : MR12 @ 0XFD0801B0</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_MR12_RESERVED_31_8                                                  0x0

                # These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0.
                # PSU_DDR_PHY_MR12_RSVD                                                           0x0

                # VREF_CA Range Select.
                # PSU_DDR_PHY_MR12_VR_CA                                                          0x1

                # Controls the VREF(ca) levels for Frequency-Set-Point[1:0].
                # PSU_DDR_PHY_MR12_VREF_CA                                                        0xd

                # LPDDR4 Mode Register 12
                #(OFFSET, MASK, VALUE)      (0XFD0801B0, 0xFFFFFFFFU ,0x0000004DU)  */
    mask_write 0XFD0801B0 0xFFFFFFFF 0x0000004D
                # Register : MR13 @ 0XFD0801B4</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_MR13_RESERVED_31_8                                                  0x0

                # Frequency Set Point Operation Mode
                # PSU_DDR_PHY_MR13_FSPOP                                                          0x0

                # Frequency Set Point Write Enable
                # PSU_DDR_PHY_MR13_FSPWR                                                          0x0

                # Data Mask Enable
                # PSU_DDR_PHY_MR13_DMD                                                            0x0

                # Refresh Rate Option
                # PSU_DDR_PHY_MR13_RRO                                                            0x0

                # VREF Current Generator
                # PSU_DDR_PHY_MR13_VRCG                                                           0x1

                # VREF Output
                # PSU_DDR_PHY_MR13_VRO                                                            0x0

                # Read Preamble Training Mode
                # PSU_DDR_PHY_MR13_RPT                                                            0x0

                # Command Bus Training
                # PSU_DDR_PHY_MR13_CBT                                                            0x0

                # LPDDR4 Mode Register 13
                #(OFFSET, MASK, VALUE)      (0XFD0801B4, 0xFFFFFFFFU ,0x00000008U)  */
    mask_write 0XFD0801B4 0xFFFFFFFF 0x00000008
                # Register : MR14 @ 0XFD0801B8</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_MR14_RESERVED_31_8                                                  0x0

                # These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0.
                # PSU_DDR_PHY_MR14_RSVD                                                           0x0

                # VREFDQ Range Selects.
                # PSU_DDR_PHY_MR14_VR_DQ                                                          0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_MR14_VREF_DQ                                                        0xd

                # LPDDR4 Mode Register 14
                #(OFFSET, MASK, VALUE)      (0XFD0801B8, 0xFFFFFFFFU ,0x0000004DU)  */
    mask_write 0XFD0801B8 0xFFFFFFFF 0x0000004D
                # Register : MR22 @ 0XFD0801D8</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_MR22_RESERVED_31_8                                                  0x0

                # These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0.
                # PSU_DDR_PHY_MR22_RSVD                                                           0x0

                # CA ODT termination disable.
                # PSU_DDR_PHY_MR22_ODTD_CA                                                        0x0

                # ODT CS override.
                # PSU_DDR_PHY_MR22_ODTE_CS                                                        0x0

                # ODT CK override.
                # PSU_DDR_PHY_MR22_ODTE_CK                                                        0x0

                # Controller ODT value for VOH calibration.
                # PSU_DDR_PHY_MR22_CODT                                                           0x0

                # LPDDR4 Mode Register 22
                #(OFFSET, MASK, VALUE)      (0XFD0801D8, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD0801D8 0xFFFFFFFF 0x00000000
                # Register : DTCR0 @ 0XFD080200</p>

                # Refresh During Training
                # PSU_DDR_PHY_DTCR0_RFSHDT                                                        0x8

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTCR0_RESERVED_27_26                                                0x0

                # Data Training Debug Rank Select
                # PSU_DDR_PHY_DTCR0_DTDRS                                                         0x1

                # Data Training with Early/Extended Gate
                # PSU_DDR_PHY_DTCR0_DTEXG                                                         0x0

                # Data Training Extended Write DQS
                # PSU_DDR_PHY_DTCR0_DTEXD                                                         0x0

                # Data Training Debug Step
                # PSU_DDR_PHY_DTCR0_DTDSTP                                                        0x0

                # Data Training Debug Enable
                # PSU_DDR_PHY_DTCR0_DTDEN                                                         0x0

                # Data Training Debug Byte Select
                # PSU_DDR_PHY_DTCR0_DTDBS                                                         0x0

                # Data Training read DBI deskewing configuration
                # PSU_DDR_PHY_DTCR0_DTRDBITR                                                      0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTCR0_RESERVED_13                                                   0x0

                # Data Training Write Bit Deskew Data Mask
                # PSU_DDR_PHY_DTCR0_DTWBDDM                                                       0x1

                # Refreshes Issued During Entry to Training
                # PSU_DDR_PHY_DTCR0_RFSHEN                                                        0x1

                # Data Training Compare Data
                # PSU_DDR_PHY_DTCR0_DTCMPD                                                        0x1

                # Data Training Using MPR
                # PSU_DDR_PHY_DTCR0_DTMPR                                                         0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTCR0_RESERVED_5_4                                                  0x0

                # Data Training Repeat Number
                # PSU_DDR_PHY_DTCR0_DTRPTN                                                        0x7

                # Data Training Configuration Register 0
                #(OFFSET, MASK, VALUE)      (0XFD080200, 0xFFFFFFFFU ,0x810011C7U)  */
    mask_write 0XFD080200 0xFFFFFFFF 0x810011C7
                # Register : DTCR1 @ 0XFD080204</p>

                # Rank Enable.
                # PSU_DDR_PHY_DTCR1_RANKEN_RSVD                                                   0x0

                # Rank Enable.
                # PSU_DDR_PHY_DTCR1_RANKEN                                                        0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTCR1_RESERVED_15_14                                                0x0

                # Data Training Rank
                # PSU_DDR_PHY_DTCR1_DTRANK                                                        0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTCR1_RESERVED_11                                                   0x0

                # Read Leveling Gate Sampling Difference
                # PSU_DDR_PHY_DTCR1_RDLVLGDIFF                                                    0x2

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTCR1_RESERVED_7                                                    0x0

                # Read Leveling Gate Shift
                # PSU_DDR_PHY_DTCR1_RDLVLGS                                                       0x3

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DTCR1_RESERVED_3                                                    0x0

                # Read Preamble Training enable
                # PSU_DDR_PHY_DTCR1_RDPRMVL_TRN                                                   0x1

                # Read Leveling Enable
                # PSU_DDR_PHY_DTCR1_RDLVLEN                                                       0x1

                # Basic Gate Training Enable
                # PSU_DDR_PHY_DTCR1_BSTEN                                                         0x0

                # Data Training Configuration Register 1
                #(OFFSET, MASK, VALUE)      (0XFD080204, 0xFFFFFFFFU ,0x00010236U)  */
    mask_write 0XFD080204 0xFFFFFFFF 0x00010236
                # Register : CATR0 @ 0XFD080240</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_CATR0_RESERVED_31_21                                                0x0

                # Minimum time (in terms of number of dram clocks) between two consectuve CA calibration command
                # PSU_DDR_PHY_CATR0_CACD                                                          0x14

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_CATR0_RESERVED_15_13                                                0x0

                # Minimum time (in terms of number of dram clocks) PUB should wait before sampling the CA response after Calibration command ha
                #  been sent to the memory
                # PSU_DDR_PHY_CATR0_CAADR                                                         0x10

                # CA_1 Response Byte Lane 1
                # PSU_DDR_PHY_CATR0_CA1BYTE1                                                      0x5

                # CA_1 Response Byte Lane 0
                # PSU_DDR_PHY_CATR0_CA1BYTE0                                                      0x4

                # CA Training Register 0
                #(OFFSET, MASK, VALUE)      (0XFD080240, 0xFFFFFFFFU ,0x00141054U)  */
    mask_write 0XFD080240 0xFFFFFFFF 0x00141054
                # Register : RIOCR5 @ 0XFD0804F4</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_RIOCR5_RESERVED_31_16                                               0x0

                # Reserved. Return zeros on reads.
                # PSU_DDR_PHY_RIOCR5_ODTOEMODE_RSVD                                               0x0

                # SDRAM On-die Termination Output Enable (OE) Mode Selection.
                # PSU_DDR_PHY_RIOCR5_ODTOEMODE                                                    0x5

                # Rank I/O Configuration Register 5
                #(OFFSET, MASK, VALUE)      (0XFD0804F4, 0xFFFFFFFFU ,0x00000005U)  */
    mask_write 0XFD0804F4 0xFFFFFFFF 0x00000005
                # Register : ACIOCR0 @ 0XFD080500</p>

                # Address/Command Slew Rate (D3F I/O Only)
                # PSU_DDR_PHY_ACIOCR0_ACSR                                                        0x0

                # SDRAM Reset I/O Mode
                # PSU_DDR_PHY_ACIOCR0_RSTIOM                                                      0x1

                # SDRAM Reset Power Down Receiver
                # PSU_DDR_PHY_ACIOCR0_RSTPDR                                                      0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_ACIOCR0_RESERVED_27                                                 0x0

                # SDRAM Reset On-Die Termination
                # PSU_DDR_PHY_ACIOCR0_RSTODT                                                      0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_ACIOCR0_RESERVED_25_10                                              0x0

                # CK Duty Cycle Correction
                # PSU_DDR_PHY_ACIOCR0_CKDCC                                                       0x0

                # AC Power Down Receiver Mode
                # PSU_DDR_PHY_ACIOCR0_ACPDRMODE                                                   0x2

                # AC On-die Termination Mode
                # PSU_DDR_PHY_ACIOCR0_ACODTMODE                                                   0x2

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_ACIOCR0_RESERVED_1                                                  0x0

                # Control delayed or non-delayed clock to CS_N/ODT?CKE AC slices.
                # PSU_DDR_PHY_ACIOCR0_ACRANKCLKSEL                                                0x0

                # AC I/O Configuration Register 0
                #(OFFSET, MASK, VALUE)      (0XFD080500, 0xFFFFFFFFU ,0x30000028U)  */
    mask_write 0XFD080500 0xFFFFFFFF 0x30000028
                # Register : ACIOCR2 @ 0XFD080508</p>

                # Clock gating for glue logic inside CLKGEN and glue logic inside CONTROL slice
                # PSU_DDR_PHY_ACIOCR2_CLKGENCLKGATE                                               0x0

                # Clock gating for Output Enable D slices [0]
                # PSU_DDR_PHY_ACIOCR2_ACOECLKGATE0                                                0x0

                # Clock gating for Power Down Receiver D slices [0]
                # PSU_DDR_PHY_ACIOCR2_ACPDRCLKGATE0                                               0x0

                # Clock gating for Termination Enable D slices [0]
                # PSU_DDR_PHY_ACIOCR2_ACTECLKGATE0                                                0x0

                # Clock gating for CK# D slices [1:0]
                # PSU_DDR_PHY_ACIOCR2_CKNCLKGATE0                                                 0x2

                # Clock gating for CK D slices [1:0]
                # PSU_DDR_PHY_ACIOCR2_CKCLKGATE0                                                  0x2

                # Clock gating for AC D slices [23:0]
                # PSU_DDR_PHY_ACIOCR2_ACCLKGATE0                                                  0x0

                # AC I/O Configuration Register 2
                #(OFFSET, MASK, VALUE)      (0XFD080508, 0xFFFFFFFFU ,0x0A000000U)  */
    mask_write 0XFD080508 0xFFFFFFFF 0x0A000000
                # Register : ACIOCR3 @ 0XFD08050C</p>

                # SDRAM Parity Output Enable (OE) Mode Selection
                # PSU_DDR_PHY_ACIOCR3_PAROEMODE                                                   0x0

                # SDRAM Bank Group Output Enable (OE) Mode Selection
                # PSU_DDR_PHY_ACIOCR3_BGOEMODE                                                    0x0

                # SDRAM Bank Address Output Enable (OE) Mode Selection
                # PSU_DDR_PHY_ACIOCR3_BAOEMODE                                                    0x0

                # SDRAM A[17] Output Enable (OE) Mode Selection
                # PSU_DDR_PHY_ACIOCR3_A17OEMODE                                                   0x0

                # SDRAM A[16] / RAS_n Output Enable (OE) Mode Selection
                # PSU_DDR_PHY_ACIOCR3_A16OEMODE                                                   0x0

                # SDRAM ACT_n Output Enable (OE) Mode Selection (DDR4 only)
                # PSU_DDR_PHY_ACIOCR3_ACTOEMODE                                                   0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_ACIOCR3_RESERVED_15_8                                               0x0

                # Reserved. Return zeros on reads.
                # PSU_DDR_PHY_ACIOCR3_CKOEMODE_RSVD                                               0x0

                # SDRAM CK Output Enable (OE) Mode Selection.
                # PSU_DDR_PHY_ACIOCR3_CKOEMODE                                                    0x9

                # AC I/O Configuration Register 3
                #(OFFSET, MASK, VALUE)      (0XFD08050C, 0xFFFFFFFFU ,0x00000009U)  */
    mask_write 0XFD08050C 0xFFFFFFFF 0x00000009
                # Register : ACIOCR4 @ 0XFD080510</p>

                # Clock gating for AC LB slices and loopback read valid slices
                # PSU_DDR_PHY_ACIOCR4_LBCLKGATE                                                   0x0

                # Clock gating for Output Enable D slices [1]
                # PSU_DDR_PHY_ACIOCR4_ACOECLKGATE1                                                0x0

                # Clock gating for Power Down Receiver D slices [1]
                # PSU_DDR_PHY_ACIOCR4_ACPDRCLKGATE1                                               0x0

                # Clock gating for Termination Enable D slices [1]
                # PSU_DDR_PHY_ACIOCR4_ACTECLKGATE1                                                0x0

                # Clock gating for CK# D slices [3:2]
                # PSU_DDR_PHY_ACIOCR4_CKNCLKGATE1                                                 0x2

                # Clock gating for CK D slices [3:2]
                # PSU_DDR_PHY_ACIOCR4_CKCLKGATE1                                                  0x2

                # Clock gating for AC D slices [47:24]
                # PSU_DDR_PHY_ACIOCR4_ACCLKGATE1                                                  0x0

                # AC I/O Configuration Register 4
                #(OFFSET, MASK, VALUE)      (0XFD080510, 0xFFFFFFFFU ,0x0A000000U)  */
    mask_write 0XFD080510 0xFFFFFFFF 0x0A000000
                # Register : IOVCR0 @ 0XFD080520</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_IOVCR0_RESERVED_31_29                                               0x0

                # Address/command lane VREF Pad Enable
                # PSU_DDR_PHY_IOVCR0_ACREFPEN                                                     0x0

                # Address/command lane Internal VREF Enable
                # PSU_DDR_PHY_IOVCR0_ACREFEEN                                                     0x0

                # Address/command lane Single-End VREF Enable
                # PSU_DDR_PHY_IOVCR0_ACREFSEN                                                     0x1

                # Address/command lane Internal VREF Enable
                # PSU_DDR_PHY_IOVCR0_ACREFIEN                                                     0x1

                # External VREF generato REFSEL range select
                # PSU_DDR_PHY_IOVCR0_ACREFESELRANGE                                               0x0

                # Address/command lane External VREF Select
                # PSU_DDR_PHY_IOVCR0_ACREFESEL                                                    0x0

                # Single ended VREF generator REFSEL range select
                # PSU_DDR_PHY_IOVCR0_ACREFSSELRANGE                                               0x1

                # Address/command lane Single-End VREF Select
                # PSU_DDR_PHY_IOVCR0_ACREFSSEL                                                    0x30

                # Internal VREF generator REFSEL ragne select
                # PSU_DDR_PHY_IOVCR0_ACVREFISELRANGE                                              0x1

                # REFSEL Control for internal AC IOs
                # PSU_DDR_PHY_IOVCR0_ACVREFISEL                                                   0x30

                # IO VREF Control Register 0
                #(OFFSET, MASK, VALUE)      (0XFD080520, 0xFFFFFFFFU ,0x0300B0B0U)  */
    mask_write 0XFD080520 0xFFFFFFFF 0x0300B0B0
                # Register : VTCR0 @ 0XFD080528</p>

                # Number of ctl_clk required to meet (> 150ns) timing requirements during DRAM DQ VREF training
                # PSU_DDR_PHY_VTCR0_TVREF                                                         0x7

                # DRM DQ VREF training Enable
                # PSU_DDR_PHY_VTCR0_DVEN                                                          0x1

                # Per Device Addressability Enable
                # PSU_DDR_PHY_VTCR0_PDAEN                                                         0x1

                # Reserved. Returns zeroes on reads.
                # PSU_DDR_PHY_VTCR0_RESERVED_26                                                   0x0

                # VREF Word Count
                # PSU_DDR_PHY_VTCR0_VWCR                                                          0x4

                # DRAM DQ VREF step size used during DRAM VREF training
                # PSU_DDR_PHY_VTCR0_DVSS                                                          0x0

                # Maximum VREF limit value used during DRAM VREF training
                # PSU_DDR_PHY_VTCR0_DVMAX                                                         0x32

                # Minimum VREF limit value used during DRAM VREF training
                # PSU_DDR_PHY_VTCR0_DVMIN                                                         0x0

                # Initial DRAM DQ VREF value used during DRAM VREF training
                # PSU_DDR_PHY_VTCR0_DVINIT                                                        0x19

                # VREF Training Control Register 0
                #(OFFSET, MASK, VALUE)      (0XFD080528, 0xFFFFFFFFU ,0xF9032019U)  */
    mask_write 0XFD080528 0xFFFFFFFF 0xF9032019
                # Register : VTCR1 @ 0XFD08052C</p>

                # Host VREF step size used during VREF training. The register value of N indicates step size of (N+1)
                # PSU_DDR_PHY_VTCR1_HVSS                                                          0x0

                # Reserved. Returns zeroes on reads.
                # PSU_DDR_PHY_VTCR1_RESERVED_27                                                   0x0

                # Maximum VREF limit value used during DRAM VREF training.
                # PSU_DDR_PHY_VTCR1_HVMAX                                                         0x7f

                # Reserved. Returns zeroes on reads.
                # PSU_DDR_PHY_VTCR1_RESERVED_19                                                   0x0

                # Minimum VREF limit value used during DRAM VREF training.
                # PSU_DDR_PHY_VTCR1_HVMIN                                                         0x0

                # Reserved. Returns zeroes on reads.
                # PSU_DDR_PHY_VTCR1_RESERVED_11                                                   0x0

                # Static Host Vref Rank Value
                # PSU_DDR_PHY_VTCR1_SHRNK                                                         0x0

                # Static Host Vref Rank Enable
                # PSU_DDR_PHY_VTCR1_SHREN                                                         0x1

                # Number of ctl_clk required to meet (> 200ns) VREF Settling timing requirements during Host IO VREF training
                # PSU_DDR_PHY_VTCR1_TVREFIO                                                       0x4

                # Eye LCDL Offset value for VREF training
                # PSU_DDR_PHY_VTCR1_EOFF                                                          0x1

                # Number of LCDL Eye points for which VREF training is repeated
                # PSU_DDR_PHY_VTCR1_ENUM                                                          0x1

                # HOST (IO) internal VREF training Enable
                # PSU_DDR_PHY_VTCR1_HVEN                                                          0x1

                # Host IO Type Control
                # PSU_DDR_PHY_VTCR1_HVIO                                                          0x1

                # VREF Training Control Register 1
                #(OFFSET, MASK, VALUE)      (0XFD08052C, 0xFFFFFFFFU ,0x07F0018FU)  */
    mask_write 0XFD08052C 0xFFFFFFFF 0x07F0018F
                # Register : ACBDLR6 @ 0XFD080558</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_ACBDLR6_RESERVED_31_30                                              0x0

                # Delay select for the BDL on Address A[3].
                # PSU_DDR_PHY_ACBDLR6_A03BD                                                       0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_ACBDLR6_RESERVED_23_22                                              0x0

                # Delay select for the BDL on Address A[2].
                # PSU_DDR_PHY_ACBDLR6_A02BD                                                       0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_ACBDLR6_RESERVED_15_14                                              0x0

                # Delay select for the BDL on Address A[1].
                # PSU_DDR_PHY_ACBDLR6_A01BD                                                       0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_ACBDLR6_RESERVED_7_6                                                0x0

                # Delay select for the BDL on Address A[0].
                # PSU_DDR_PHY_ACBDLR6_A00BD                                                       0x0

                # AC Bit Delay Line Register 6
                #(OFFSET, MASK, VALUE)      (0XFD080558, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD080558 0xFFFFFFFF 0x00000000
                # Register : ACBDLR7 @ 0XFD08055C</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_ACBDLR7_RESERVED_31_30                                              0x0

                # Delay select for the BDL on Address A[7].
                # PSU_DDR_PHY_ACBDLR7_A07BD                                                       0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_ACBDLR7_RESERVED_23_22                                              0x0

                # Delay select for the BDL on Address A[6].
                # PSU_DDR_PHY_ACBDLR7_A06BD                                                       0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_ACBDLR7_RESERVED_15_14                                              0x0

                # Delay select for the BDL on Address A[5].
                # PSU_DDR_PHY_ACBDLR7_A05BD                                                       0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_ACBDLR7_RESERVED_7_6                                                0x0

                # Delay select for the BDL on Address A[4].
                # PSU_DDR_PHY_ACBDLR7_A04BD                                                       0x0

                # AC Bit Delay Line Register 7
                #(OFFSET, MASK, VALUE)      (0XFD08055C, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD08055C 0xFFFFFFFF 0x00000000
                # Register : ACBDLR8 @ 0XFD080560</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_ACBDLR8_RESERVED_31_30                                              0x0

                # Delay select for the BDL on Address A[11].
                # PSU_DDR_PHY_ACBDLR8_A11BD                                                       0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_ACBDLR8_RESERVED_23_22                                              0x0

                # Delay select for the BDL on Address A[10].
                # PSU_DDR_PHY_ACBDLR8_A10BD                                                       0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_ACBDLR8_RESERVED_15_14                                              0x0

                # Delay select for the BDL on Address A[9].
                # PSU_DDR_PHY_ACBDLR8_A09BD                                                       0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_ACBDLR8_RESERVED_7_6                                                0x0

                # Delay select for the BDL on Address A[8].
                # PSU_DDR_PHY_ACBDLR8_A08BD                                                       0x0

                # AC Bit Delay Line Register 8
                #(OFFSET, MASK, VALUE)      (0XFD080560, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD080560 0xFFFFFFFF 0x00000000
                # Register : ZQCR @ 0XFD080680</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_ZQCR_RESERVED_31_26                                                 0x0

                # ZQ VREF Range
                # PSU_DDR_PHY_ZQCR_ZQREFISELRANGE                                                 0x0

                # Programmable Wait for Frequency B
                # PSU_DDR_PHY_ZQCR_PGWAIT_FRQB                                                    0x11

                # Programmable Wait for Frequency A
                # PSU_DDR_PHY_ZQCR_PGWAIT_FRQA                                                    0x11

                # ZQ VREF Pad Enable
                # PSU_DDR_PHY_ZQCR_ZQREFPEN                                                       0x0

                # ZQ Internal VREF Enable
                # PSU_DDR_PHY_ZQCR_ZQREFIEN                                                       0x1

                # Choice of termination mode
                # PSU_DDR_PHY_ZQCR_ODT_MODE                                                       0x1

                # Force ZCAL VT update
                # PSU_DDR_PHY_ZQCR_FORCE_ZCAL_VT_UPDATE                                           0x0

                # IO VT Drift Limit
                # PSU_DDR_PHY_ZQCR_IODLMT                                                         0x2

                # Averaging algorithm enable, if set, enables averaging algorithm
                # PSU_DDR_PHY_ZQCR_AVGEN                                                          0x1

                # Maximum number of averaging rounds to be used by averaging algorithm
                # PSU_DDR_PHY_ZQCR_AVGMAX                                                         0x2

                # ZQ Calibration Type
                # PSU_DDR_PHY_ZQCR_ZCALT                                                          0x0

                # ZQ Power Down
                # PSU_DDR_PHY_ZQCR_ZQPD                                                           0x0

                # ZQ Impedance Control Register
                #(OFFSET, MASK, VALUE)      (0XFD080680, 0xFFFFFFFFU ,0x008A2A58U)  */
    mask_write 0XFD080680 0xFFFFFFFF 0x008A2A58
                # Register : ZQ0PR0 @ 0XFD080684</p>

                # Pull-down drive strength ZCTRL over-ride enable
                # PSU_DDR_PHY_ZQ0PR0_PD_DRV_ZDEN                                                  0x0

                # Pull-up drive strength ZCTRL over-ride enable
                # PSU_DDR_PHY_ZQ0PR0_PU_DRV_ZDEN                                                  0x0

                # Pull-down termination ZCTRL over-ride enable
                # PSU_DDR_PHY_ZQ0PR0_PD_ODT_ZDEN                                                  0x0

                # Pull-up termination ZCTRL over-ride enable
                # PSU_DDR_PHY_ZQ0PR0_PU_ODT_ZDEN                                                  0x0

                # Calibration segment bypass
                # PSU_DDR_PHY_ZQ0PR0_ZSEGBYP                                                      0x0

                # VREF latch mode controls the mode in which the ZLE pin of the PVREF cell is driven by the PUB
                # PSU_DDR_PHY_ZQ0PR0_ZLE_MODE                                                     0x0

                # Termination adjustment
                # PSU_DDR_PHY_ZQ0PR0_ODT_ADJUST                                                   0x0

                # Pulldown drive strength adjustment
                # PSU_DDR_PHY_ZQ0PR0_PD_DRV_ADJUST                                                0x0

                # Pullup drive strength adjustment
                # PSU_DDR_PHY_ZQ0PR0_PU_DRV_ADJUST                                                0x0

                # DRAM Impedance Divide Ratio
                # PSU_DDR_PHY_ZQ0PR0_ZPROG_DRAM_ODT                                               0x7

                # HOST Impedance Divide Ratio
                # PSU_DDR_PHY_ZQ0PR0_ZPROG_HOST_ODT                                               0x7

                # Impedance Divide Ratio (pulldown drive calibration during asymmetric drive strength calibration)
                # PSU_DDR_PHY_ZQ0PR0_ZPROG_ASYM_DRV_PD                                            0xd

                # Impedance Divide Ratio (pullup drive calibration during asymmetric drive strength calibration)
                # PSU_DDR_PHY_ZQ0PR0_ZPROG_ASYM_DRV_PU                                            0xd

                # ZQ n Impedance Control Program Register 0
                #(OFFSET, MASK, VALUE)      (0XFD080684, 0xFFFFFFFFU ,0x000077DDU)  */
    mask_write 0XFD080684 0xFFFFFFFF 0x000077DD
                # Register : ZQ0OR0 @ 0XFD080694</p>

                # Reserved. Return zeros on reads.
                # PSU_DDR_PHY_ZQ0OR0_RESERVED_31_26                                               0x0

                # Override value for the pull-up output impedance
                # PSU_DDR_PHY_ZQ0OR0_ZDATA_PU_DRV_OVRD                                            0x1e1

                # Reserved. Return zeros on reads.
                # PSU_DDR_PHY_ZQ0OR0_RESERVED_15_10                                               0x0

                # Override value for the pull-down output impedance
                # PSU_DDR_PHY_ZQ0OR0_ZDATA_PD_DRV_OVRD                                            0x210

                # ZQ n Impedance Control Override Data Register 0
                #(OFFSET, MASK, VALUE)      (0XFD080694, 0xFFFFFFFFU ,0x01E10210U)  */
    mask_write 0XFD080694 0xFFFFFFFF 0x01E10210
                # Register : ZQ0OR1 @ 0XFD080698</p>

                # Reserved. Return zeros on reads.
                # PSU_DDR_PHY_ZQ0OR1_RESERVED_31_26                                               0x0

                # Override value for the pull-up termination
                # PSU_DDR_PHY_ZQ0OR1_ZDATA_PU_ODT_OVRD                                            0x1e1

                # Reserved. Return zeros on reads.
                # PSU_DDR_PHY_ZQ0OR1_RESERVED_15_10                                               0x0

                # Override value for the pull-down termination
                # PSU_DDR_PHY_ZQ0OR1_ZDATA_PD_ODT_OVRD                                            0x0

                # ZQ n Impedance Control Override Data Register 1
                #(OFFSET, MASK, VALUE)      (0XFD080698, 0xFFFFFFFFU ,0x01E10000U)  */
    mask_write 0XFD080698 0xFFFFFFFF 0x01E10000
                # Register : ZQ1PR0 @ 0XFD0806A4</p>

                # Pull-down drive strength ZCTRL over-ride enable
                # PSU_DDR_PHY_ZQ1PR0_PD_DRV_ZDEN                                                  0x0

                # Pull-up drive strength ZCTRL over-ride enable
                # PSU_DDR_PHY_ZQ1PR0_PU_DRV_ZDEN                                                  0x0

                # Pull-down termination ZCTRL over-ride enable
                # PSU_DDR_PHY_ZQ1PR0_PD_ODT_ZDEN                                                  0x0

                # Pull-up termination ZCTRL over-ride enable
                # PSU_DDR_PHY_ZQ1PR0_PU_ODT_ZDEN                                                  0x0

                # Calibration segment bypass
                # PSU_DDR_PHY_ZQ1PR0_ZSEGBYP                                                      0x0

                # VREF latch mode controls the mode in which the ZLE pin of the PVREF cell is driven by the PUB
                # PSU_DDR_PHY_ZQ1PR0_ZLE_MODE                                                     0x0

                # Termination adjustment
                # PSU_DDR_PHY_ZQ1PR0_ODT_ADJUST                                                   0x0

                # Pulldown drive strength adjustment
                # PSU_DDR_PHY_ZQ1PR0_PD_DRV_ADJUST                                                0x1

                # Pullup drive strength adjustment
                # PSU_DDR_PHY_ZQ1PR0_PU_DRV_ADJUST                                                0x0

                # DRAM Impedance Divide Ratio
                # PSU_DDR_PHY_ZQ1PR0_ZPROG_DRAM_ODT                                               0x7

                # HOST Impedance Divide Ratio
                # PSU_DDR_PHY_ZQ1PR0_ZPROG_HOST_ODT                                               0xb

                # Impedance Divide Ratio (pulldown drive calibration during asymmetric drive strength calibration)
                # PSU_DDR_PHY_ZQ1PR0_ZPROG_ASYM_DRV_PD                                            0xd

                # Impedance Divide Ratio (pullup drive calibration during asymmetric drive strength calibration)
                # PSU_DDR_PHY_ZQ1PR0_ZPROG_ASYM_DRV_PU                                            0xb

                # ZQ n Impedance Control Program Register 0
                #(OFFSET, MASK, VALUE)      (0XFD0806A4, 0xFFFFFFFFU ,0x00087BDBU)  */
    mask_write 0XFD0806A4 0xFFFFFFFF 0x00087BDB
                # Register : DX0GCR0 @ 0XFD080700</p>

                # Calibration Bypass
                # PSU_DDR_PHY_DX0GCR0_CALBYP                                                      0x0

                # Master Delay Line Enable
                # PSU_DDR_PHY_DX0GCR0_MDLEN                                                       0x1

                # Configurable ODT(TE) Phase Shift
                # PSU_DDR_PHY_DX0GCR0_CODTSHFT                                                    0x0

                # DQS Duty Cycle Correction
                # PSU_DDR_PHY_DX0GCR0_DQSDCC                                                      0x0

                # Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd input for the respective bypte lane of the PHY
                # PSU_DDR_PHY_DX0GCR0_RDDLY                                                       0x8

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX0GCR0_RESERVED_19_14                                              0x0

                # DQSNSE Power Down Receiver
                # PSU_DDR_PHY_DX0GCR0_DQSNSEPDR                                                   0x0

                # DQSSE Power Down Receiver
                # PSU_DDR_PHY_DX0GCR0_DQSSEPDR                                                    0x0

                # RTT On Additive Latency
                # PSU_DDR_PHY_DX0GCR0_RTTOAL                                                      0x0

                # RTT Output Hold
                # PSU_DDR_PHY_DX0GCR0_RTTOH                                                       0x3

                # Configurable PDR Phase Shift
                # PSU_DDR_PHY_DX0GCR0_CPDRSHFT                                                    0x0

                # DQSR Power Down
                # PSU_DDR_PHY_DX0GCR0_DQSRPD                                                      0x0

                # DQSG Power Down Receiver
                # PSU_DDR_PHY_DX0GCR0_DQSGPDR                                                     0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX0GCR0_RESERVED_4                                                  0x0

                # DQSG On-Die Termination
                # PSU_DDR_PHY_DX0GCR0_DQSGODT                                                     0x0

                # DQSG Output Enable
                # PSU_DDR_PHY_DX0GCR0_DQSGOE                                                      0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX0GCR0_RESERVED_1_0                                                0x0

                # DATX8 n General Configuration Register 0
                #(OFFSET, MASK, VALUE)      (0XFD080700, 0xFFFFFFFFU ,0x40800604U)  */
    mask_write 0XFD080700 0xFFFFFFFF 0x40800604
                # Register : DX0GCR4 @ 0XFD080710</p>

                # Byte lane VREF IOM (Used only by D4MU IOs)
                # PSU_DDR_PHY_DX0GCR4_RESERVED_31_29                                              0x0

                # Byte Lane VREF Pad Enable
                # PSU_DDR_PHY_DX0GCR4_DXREFPEN                                                    0x0

                # Byte Lane Internal VREF Enable
                # PSU_DDR_PHY_DX0GCR4_DXREFEEN                                                    0x3

                # Byte Lane Single-End VREF Enable
                # PSU_DDR_PHY_DX0GCR4_DXREFSEN                                                    0x1

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX0GCR4_RESERVED_24                                                 0x0

                # External VREF generator REFSEL range select
                # PSU_DDR_PHY_DX0GCR4_DXREFESELRANGE                                              0x0

                # Byte Lane External VREF Select
                # PSU_DDR_PHY_DX0GCR4_DXREFESEL                                                   0x0

                # Single ended VREF generator REFSEL range select
                # PSU_DDR_PHY_DX0GCR4_DXREFSSELRANGE                                              0x1

                # Byte Lane Single-End VREF Select
                # PSU_DDR_PHY_DX0GCR4_DXREFSSEL                                                   0x30

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX0GCR4_RESERVED_7_6                                                0x0

                # VREF Enable control for DQ IO (Single Ended) buffers of a byte lane.
                # PSU_DDR_PHY_DX0GCR4_DXREFIEN                                                    0xf

                # VRMON control for DQ IO (Single Ended) buffers of a byte lane.
                # PSU_DDR_PHY_DX0GCR4_DXREFIMON                                                   0x0

                # DATX8 n General Configuration Register 4
                #(OFFSET, MASK, VALUE)      (0XFD080710, 0xFFFFFFFFU ,0x0E00B03CU)  */
    mask_write 0XFD080710 0xFFFFFFFF 0x0E00B03C
                # Register : DX0GCR5 @ 0XFD080714</p>

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX0GCR5_RESERVED_31                                                 0x0

                # Byte Lane internal VREF Select for Rank 3
                # PSU_DDR_PHY_DX0GCR5_DXREFISELR3                                                 0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX0GCR5_RESERVED_23                                                 0x0

                # Byte Lane internal VREF Select for Rank 2
                # PSU_DDR_PHY_DX0GCR5_DXREFISELR2                                                 0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX0GCR5_RESERVED_15                                                 0x0

                # Byte Lane internal VREF Select for Rank 1
                # PSU_DDR_PHY_DX0GCR5_DXREFISELR1                                                 0x55

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX0GCR5_RESERVED_7                                                  0x0

                # Byte Lane internal VREF Select for Rank 0
                # PSU_DDR_PHY_DX0GCR5_DXREFISELR0                                                 0x55

                # DATX8 n General Configuration Register 5
                #(OFFSET, MASK, VALUE)      (0XFD080714, 0xFFFFFFFFU ,0x09095555U)  */
    mask_write 0XFD080714 0xFFFFFFFF 0x09095555
                # Register : DX0GCR6 @ 0XFD080718</p>

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX0GCR6_RESERVED_31_30                                              0x0

                # DRAM DQ VREF Select for Rank3
                # PSU_DDR_PHY_DX0GCR6_DXDQVREFR3                                                  0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX0GCR6_RESERVED_23_22                                              0x0

                # DRAM DQ VREF Select for Rank2
                # PSU_DDR_PHY_DX0GCR6_DXDQVREFR2                                                  0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX0GCR6_RESERVED_15_14                                              0x0

                # DRAM DQ VREF Select for Rank1
                # PSU_DDR_PHY_DX0GCR6_DXDQVREFR1                                                  0x2b

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX0GCR6_RESERVED_7_6                                                0x0

                # DRAM DQ VREF Select for Rank0
                # PSU_DDR_PHY_DX0GCR6_DXDQVREFR0                                                  0x2b

                # DATX8 n General Configuration Register 6
                #(OFFSET, MASK, VALUE)      (0XFD080718, 0xFFFFFFFFU ,0x09092B2BU)  */
    mask_write 0XFD080718 0xFFFFFFFF 0x09092B2B
                # Register : DX0LCDLR2 @ 0XFD080788</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX0LCDLR2_RESERVED_31_25                                            0x0

                # Reserved. Caution, do not write to this register field.
                # PSU_DDR_PHY_DX0LCDLR2_RESERVED_24_16                                            0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX0LCDLR2_RESERVED_15_9                                             0x0

                # Read DQS Gating Delay
                # PSU_DDR_PHY_DX0LCDLR2_DQSGD                                                     0x0

                # DATX8 n Local Calibrated Delay Line Register 2
                #(OFFSET, MASK, VALUE)      (0XFD080788, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD080788 0xFFFFFFFF 0x00000000
                # Register : DX0GTR0 @ 0XFD0807C0</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX0GTR0_RESERVED_31_24                                              0x0

                # DQ Write Path Latency Pipeline
                # PSU_DDR_PHY_DX0GTR0_WDQSL                                                       0x0

                # Reserved. Caution, do not write to this register field.
                # PSU_DDR_PHY_DX0GTR0_RESERVED_23_20                                              0x0

                # Write Leveling System Latency
                # PSU_DDR_PHY_DX0GTR0_WLSL                                                        0x2

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX0GTR0_RESERVED_15_13                                              0x0

                # Reserved. Caution, do not write to this register field.
                # PSU_DDR_PHY_DX0GTR0_RESERVED_12_8                                               0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX0GTR0_RESERVED_7_5                                                0x0

                # DQS Gating System Latency
                # PSU_DDR_PHY_DX0GTR0_DGSL                                                        0x0

                # DATX8 n General Timing Register 0
                #(OFFSET, MASK, VALUE)      (0XFD0807C0, 0xFFFFFFFFU ,0x00020000U)  */
    mask_write 0XFD0807C0 0xFFFFFFFF 0x00020000
                # Register : DX1GCR0 @ 0XFD080800</p>

                # Calibration Bypass
                # PSU_DDR_PHY_DX1GCR0_CALBYP                                                      0x0

                # Master Delay Line Enable
                # PSU_DDR_PHY_DX1GCR0_MDLEN                                                       0x1

                # Configurable ODT(TE) Phase Shift
                # PSU_DDR_PHY_DX1GCR0_CODTSHFT                                                    0x0

                # DQS Duty Cycle Correction
                # PSU_DDR_PHY_DX1GCR0_DQSDCC                                                      0x0

                # Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd input for the respective bypte lane of the PHY
                # PSU_DDR_PHY_DX1GCR0_RDDLY                                                       0x8

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX1GCR0_RESERVED_19_14                                              0x0

                # DQSNSE Power Down Receiver
                # PSU_DDR_PHY_DX1GCR0_DQSNSEPDR                                                   0x0

                # DQSSE Power Down Receiver
                # PSU_DDR_PHY_DX1GCR0_DQSSEPDR                                                    0x0

                # RTT On Additive Latency
                # PSU_DDR_PHY_DX1GCR0_RTTOAL                                                      0x0

                # RTT Output Hold
                # PSU_DDR_PHY_DX1GCR0_RTTOH                                                       0x3

                # Configurable PDR Phase Shift
                # PSU_DDR_PHY_DX1GCR0_CPDRSHFT                                                    0x0

                # DQSR Power Down
                # PSU_DDR_PHY_DX1GCR0_DQSRPD                                                      0x0

                # DQSG Power Down Receiver
                # PSU_DDR_PHY_DX1GCR0_DQSGPDR                                                     0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX1GCR0_RESERVED_4                                                  0x0

                # DQSG On-Die Termination
                # PSU_DDR_PHY_DX1GCR0_DQSGODT                                                     0x0

                # DQSG Output Enable
                # PSU_DDR_PHY_DX1GCR0_DQSGOE                                                      0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX1GCR0_RESERVED_1_0                                                0x0

                # DATX8 n General Configuration Register 0
                #(OFFSET, MASK, VALUE)      (0XFD080800, 0xFFFFFFFFU ,0x40800604U)  */
    mask_write 0XFD080800 0xFFFFFFFF 0x40800604
                # Register : DX1GCR4 @ 0XFD080810</p>

                # Byte lane VREF IOM (Used only by D4MU IOs)
                # PSU_DDR_PHY_DX1GCR4_RESERVED_31_29                                              0x0

                # Byte Lane VREF Pad Enable
                # PSU_DDR_PHY_DX1GCR4_DXREFPEN                                                    0x0

                # Byte Lane Internal VREF Enable
                # PSU_DDR_PHY_DX1GCR4_DXREFEEN                                                    0x3

                # Byte Lane Single-End VREF Enable
                # PSU_DDR_PHY_DX1GCR4_DXREFSEN                                                    0x1

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX1GCR4_RESERVED_24                                                 0x0

                # External VREF generator REFSEL range select
                # PSU_DDR_PHY_DX1GCR4_DXREFESELRANGE                                              0x0

                # Byte Lane External VREF Select
                # PSU_DDR_PHY_DX1GCR4_DXREFESEL                                                   0x0

                # Single ended VREF generator REFSEL range select
                # PSU_DDR_PHY_DX1GCR4_DXREFSSELRANGE                                              0x1

                # Byte Lane Single-End VREF Select
                # PSU_DDR_PHY_DX1GCR4_DXREFSSEL                                                   0x30

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX1GCR4_RESERVED_7_6                                                0x0

                # VREF Enable control for DQ IO (Single Ended) buffers of a byte lane.
                # PSU_DDR_PHY_DX1GCR4_DXREFIEN                                                    0xf

                # VRMON control for DQ IO (Single Ended) buffers of a byte lane.
                # PSU_DDR_PHY_DX1GCR4_DXREFIMON                                                   0x0

                # DATX8 n General Configuration Register 4
                #(OFFSET, MASK, VALUE)      (0XFD080810, 0xFFFFFFFFU ,0x0E00B03CU)  */
    mask_write 0XFD080810 0xFFFFFFFF 0x0E00B03C
                # Register : DX1GCR5 @ 0XFD080814</p>

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX1GCR5_RESERVED_31                                                 0x0

                # Byte Lane internal VREF Select for Rank 3
                # PSU_DDR_PHY_DX1GCR5_DXREFISELR3                                                 0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX1GCR5_RESERVED_23                                                 0x0

                # Byte Lane internal VREF Select for Rank 2
                # PSU_DDR_PHY_DX1GCR5_DXREFISELR2                                                 0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX1GCR5_RESERVED_15                                                 0x0

                # Byte Lane internal VREF Select for Rank 1
                # PSU_DDR_PHY_DX1GCR5_DXREFISELR1                                                 0x55

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX1GCR5_RESERVED_7                                                  0x0

                # Byte Lane internal VREF Select for Rank 0
                # PSU_DDR_PHY_DX1GCR5_DXREFISELR0                                                 0x55

                # DATX8 n General Configuration Register 5
                #(OFFSET, MASK, VALUE)      (0XFD080814, 0xFFFFFFFFU ,0x09095555U)  */
    mask_write 0XFD080814 0xFFFFFFFF 0x09095555
                # Register : DX1GCR6 @ 0XFD080818</p>

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX1GCR6_RESERVED_31_30                                              0x0

                # DRAM DQ VREF Select for Rank3
                # PSU_DDR_PHY_DX1GCR6_DXDQVREFR3                                                  0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX1GCR6_RESERVED_23_22                                              0x0

                # DRAM DQ VREF Select for Rank2
                # PSU_DDR_PHY_DX1GCR6_DXDQVREFR2                                                  0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX1GCR6_RESERVED_15_14                                              0x0

                # DRAM DQ VREF Select for Rank1
                # PSU_DDR_PHY_DX1GCR6_DXDQVREFR1                                                  0x2b

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX1GCR6_RESERVED_7_6                                                0x0

                # DRAM DQ VREF Select for Rank0
                # PSU_DDR_PHY_DX1GCR6_DXDQVREFR0                                                  0x2b

                # DATX8 n General Configuration Register 6
                #(OFFSET, MASK, VALUE)      (0XFD080818, 0xFFFFFFFFU ,0x09092B2BU)  */
    mask_write 0XFD080818 0xFFFFFFFF 0x09092B2B
                # Register : DX1LCDLR2 @ 0XFD080888</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX1LCDLR2_RESERVED_31_25                                            0x0

                # Reserved. Caution, do not write to this register field.
                # PSU_DDR_PHY_DX1LCDLR2_RESERVED_24_16                                            0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX1LCDLR2_RESERVED_15_9                                             0x0

                # Read DQS Gating Delay
                # PSU_DDR_PHY_DX1LCDLR2_DQSGD                                                     0x0

                # DATX8 n Local Calibrated Delay Line Register 2
                #(OFFSET, MASK, VALUE)      (0XFD080888, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD080888 0xFFFFFFFF 0x00000000
                # Register : DX1GTR0 @ 0XFD0808C0</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX1GTR0_RESERVED_31_24                                              0x0

                # DQ Write Path Latency Pipeline
                # PSU_DDR_PHY_DX1GTR0_WDQSL                                                       0x0

                # Reserved. Caution, do not write to this register field.
                # PSU_DDR_PHY_DX1GTR0_RESERVED_23_20                                              0x0

                # Write Leveling System Latency
                # PSU_DDR_PHY_DX1GTR0_WLSL                                                        0x2

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX1GTR0_RESERVED_15_13                                              0x0

                # Reserved. Caution, do not write to this register field.
                # PSU_DDR_PHY_DX1GTR0_RESERVED_12_8                                               0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX1GTR0_RESERVED_7_5                                                0x0

                # DQS Gating System Latency
                # PSU_DDR_PHY_DX1GTR0_DGSL                                                        0x0

                # DATX8 n General Timing Register 0
                #(OFFSET, MASK, VALUE)      (0XFD0808C0, 0xFFFFFFFFU ,0x00020000U)  */
    mask_write 0XFD0808C0 0xFFFFFFFF 0x00020000
                # Register : DX2GCR0 @ 0XFD080900</p>

                # Calibration Bypass
                # PSU_DDR_PHY_DX2GCR0_CALBYP                                                      0x0

                # Master Delay Line Enable
                # PSU_DDR_PHY_DX2GCR0_MDLEN                                                       0x1

                # Configurable ODT(TE) Phase Shift
                # PSU_DDR_PHY_DX2GCR0_CODTSHFT                                                    0x0

                # DQS Duty Cycle Correction
                # PSU_DDR_PHY_DX2GCR0_DQSDCC                                                      0x0

                # Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd input for the respective bypte lane of the PHY
                # PSU_DDR_PHY_DX2GCR0_RDDLY                                                       0x8

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX2GCR0_RESERVED_19_14                                              0x0

                # DQSNSE Power Down Receiver
                # PSU_DDR_PHY_DX2GCR0_DQSNSEPDR                                                   0x0

                # DQSSE Power Down Receiver
                # PSU_DDR_PHY_DX2GCR0_DQSSEPDR                                                    0x0

                # RTT On Additive Latency
                # PSU_DDR_PHY_DX2GCR0_RTTOAL                                                      0x0

                # RTT Output Hold
                # PSU_DDR_PHY_DX2GCR0_RTTOH                                                       0x3

                # Configurable PDR Phase Shift
                # PSU_DDR_PHY_DX2GCR0_CPDRSHFT                                                    0x0

                # DQSR Power Down
                # PSU_DDR_PHY_DX2GCR0_DQSRPD                                                      0x0

                # DQSG Power Down Receiver
                # PSU_DDR_PHY_DX2GCR0_DQSGPDR                                                     0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX2GCR0_RESERVED_4                                                  0x0

                # DQSG On-Die Termination
                # PSU_DDR_PHY_DX2GCR0_DQSGODT                                                     0x0

                # DQSG Output Enable
                # PSU_DDR_PHY_DX2GCR0_DQSGOE                                                      0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX2GCR0_RESERVED_1_0                                                0x0

                # DATX8 n General Configuration Register 0
                #(OFFSET, MASK, VALUE)      (0XFD080900, 0xFFFFFFFFU ,0x40800604U)  */
    mask_write 0XFD080900 0xFFFFFFFF 0x40800604
                # Register : DX2GCR1 @ 0XFD080904</p>

                # Enables the PDR mode for DQ[7:0]
                # PSU_DDR_PHY_DX2GCR1_DXPDRMODE                                                   0x0

                # Reserved. Returns zeroes on reads.
                # PSU_DDR_PHY_DX2GCR1_RESERVED_15                                                 0x0

                # Select the delayed or non-delayed read data strobe #
                # PSU_DDR_PHY_DX2GCR1_QSNSEL                                                      0x1

                # Select the delayed or non-delayed read data strobe
                # PSU_DDR_PHY_DX2GCR1_QSSEL                                                       0x1

                # Enables Read Data Strobe in a byte lane
                # PSU_DDR_PHY_DX2GCR1_OEEN                                                        0x1

                # Enables PDR in a byte lane
                # PSU_DDR_PHY_DX2GCR1_PDREN                                                       0x1

                # Enables ODT/TE in a byte lane
                # PSU_DDR_PHY_DX2GCR1_TEEN                                                        0x1

                # Enables Write Data strobe in a byte lane
                # PSU_DDR_PHY_DX2GCR1_DSEN                                                        0x1

                # Enables DM pin in a byte lane
                # PSU_DDR_PHY_DX2GCR1_DMEN                                                        0x1

                # Enables DQ corresponding to each bit in a byte
                # PSU_DDR_PHY_DX2GCR1_DQEN                                                        0xff

                # DATX8 n General Configuration Register 1
                #(OFFSET, MASK, VALUE)      (0XFD080904, 0xFFFFFFFFU ,0x00007FFFU)  */
    mask_write 0XFD080904 0xFFFFFFFF 0x00007FFF
                # Register : DX2GCR4 @ 0XFD080910</p>

                # Byte lane VREF IOM (Used only by D4MU IOs)
                # PSU_DDR_PHY_DX2GCR4_RESERVED_31_29                                              0x0

                # Byte Lane VREF Pad Enable
                # PSU_DDR_PHY_DX2GCR4_DXREFPEN                                                    0x0

                # Byte Lane Internal VREF Enable
                # PSU_DDR_PHY_DX2GCR4_DXREFEEN                                                    0x3

                # Byte Lane Single-End VREF Enable
                # PSU_DDR_PHY_DX2GCR4_DXREFSEN                                                    0x1

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX2GCR4_RESERVED_24                                                 0x0

                # External VREF generator REFSEL range select
                # PSU_DDR_PHY_DX2GCR4_DXREFESELRANGE                                              0x0

                # Byte Lane External VREF Select
                # PSU_DDR_PHY_DX2GCR4_DXREFESEL                                                   0x0

                # Single ended VREF generator REFSEL range select
                # PSU_DDR_PHY_DX2GCR4_DXREFSSELRANGE                                              0x1

                # Byte Lane Single-End VREF Select
                # PSU_DDR_PHY_DX2GCR4_DXREFSSEL                                                   0x30

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX2GCR4_RESERVED_7_6                                                0x0

                # VREF Enable control for DQ IO (Single Ended) buffers of a byte lane.
                # PSU_DDR_PHY_DX2GCR4_DXREFIEN                                                    0xf

                # VRMON control for DQ IO (Single Ended) buffers of a byte lane.
                # PSU_DDR_PHY_DX2GCR4_DXREFIMON                                                   0x0

                # DATX8 n General Configuration Register 4
                #(OFFSET, MASK, VALUE)      (0XFD080910, 0xFFFFFFFFU ,0x0E00B03CU)  */
    mask_write 0XFD080910 0xFFFFFFFF 0x0E00B03C
                # Register : DX2GCR5 @ 0XFD080914</p>

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX2GCR5_RESERVED_31                                                 0x0

                # Byte Lane internal VREF Select for Rank 3
                # PSU_DDR_PHY_DX2GCR5_DXREFISELR3                                                 0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX2GCR5_RESERVED_23                                                 0x0

                # Byte Lane internal VREF Select for Rank 2
                # PSU_DDR_PHY_DX2GCR5_DXREFISELR2                                                 0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX2GCR5_RESERVED_15                                                 0x0

                # Byte Lane internal VREF Select for Rank 1
                # PSU_DDR_PHY_DX2GCR5_DXREFISELR1                                                 0x55

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX2GCR5_RESERVED_7                                                  0x0

                # Byte Lane internal VREF Select for Rank 0
                # PSU_DDR_PHY_DX2GCR5_DXREFISELR0                                                 0x55

                # DATX8 n General Configuration Register 5
                #(OFFSET, MASK, VALUE)      (0XFD080914, 0xFFFFFFFFU ,0x09095555U)  */
    mask_write 0XFD080914 0xFFFFFFFF 0x09095555
                # Register : DX2GCR6 @ 0XFD080918</p>

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX2GCR6_RESERVED_31_30                                              0x0

                # DRAM DQ VREF Select for Rank3
                # PSU_DDR_PHY_DX2GCR6_DXDQVREFR3                                                  0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX2GCR6_RESERVED_23_22                                              0x0

                # DRAM DQ VREF Select for Rank2
                # PSU_DDR_PHY_DX2GCR6_DXDQVREFR2                                                  0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX2GCR6_RESERVED_15_14                                              0x0

                # DRAM DQ VREF Select for Rank1
                # PSU_DDR_PHY_DX2GCR6_DXDQVREFR1                                                  0x2b

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX2GCR6_RESERVED_7_6                                                0x0

                # DRAM DQ VREF Select for Rank0
                # PSU_DDR_PHY_DX2GCR6_DXDQVREFR0                                                  0x2b

                # DATX8 n General Configuration Register 6
                #(OFFSET, MASK, VALUE)      (0XFD080918, 0xFFFFFFFFU ,0x09092B2BU)  */
    mask_write 0XFD080918 0xFFFFFFFF 0x09092B2B
                # Register : DX2LCDLR2 @ 0XFD080988</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX2LCDLR2_RESERVED_31_25                                            0x0

                # Reserved. Caution, do not write to this register field.
                # PSU_DDR_PHY_DX2LCDLR2_RESERVED_24_16                                            0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX2LCDLR2_RESERVED_15_9                                             0x0

                # Read DQS Gating Delay
                # PSU_DDR_PHY_DX2LCDLR2_DQSGD                                                     0x0

                # DATX8 n Local Calibrated Delay Line Register 2
                #(OFFSET, MASK, VALUE)      (0XFD080988, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD080988 0xFFFFFFFF 0x00000000
                # Register : DX2GTR0 @ 0XFD0809C0</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX2GTR0_RESERVED_31_24                                              0x0

                # DQ Write Path Latency Pipeline
                # PSU_DDR_PHY_DX2GTR0_WDQSL                                                       0x0

                # Reserved. Caution, do not write to this register field.
                # PSU_DDR_PHY_DX2GTR0_RESERVED_23_20                                              0x0

                # Write Leveling System Latency
                # PSU_DDR_PHY_DX2GTR0_WLSL                                                        0x2

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX2GTR0_RESERVED_15_13                                              0x0

                # Reserved. Caution, do not write to this register field.
                # PSU_DDR_PHY_DX2GTR0_RESERVED_12_8                                               0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX2GTR0_RESERVED_7_5                                                0x0

                # DQS Gating System Latency
                # PSU_DDR_PHY_DX2GTR0_DGSL                                                        0x0

                # DATX8 n General Timing Register 0
                #(OFFSET, MASK, VALUE)      (0XFD0809C0, 0xFFFFFFFFU ,0x00020000U)  */
    mask_write 0XFD0809C0 0xFFFFFFFF 0x00020000
                # Register : DX3GCR0 @ 0XFD080A00</p>

                # Calibration Bypass
                # PSU_DDR_PHY_DX3GCR0_CALBYP                                                      0x0

                # Master Delay Line Enable
                # PSU_DDR_PHY_DX3GCR0_MDLEN                                                       0x1

                # Configurable ODT(TE) Phase Shift
                # PSU_DDR_PHY_DX3GCR0_CODTSHFT                                                    0x0

                # DQS Duty Cycle Correction
                # PSU_DDR_PHY_DX3GCR0_DQSDCC                                                      0x0

                # Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd input for the respective bypte lane of the PHY
                # PSU_DDR_PHY_DX3GCR0_RDDLY                                                       0x8

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX3GCR0_RESERVED_19_14                                              0x0

                # DQSNSE Power Down Receiver
                # PSU_DDR_PHY_DX3GCR0_DQSNSEPDR                                                   0x0

                # DQSSE Power Down Receiver
                # PSU_DDR_PHY_DX3GCR0_DQSSEPDR                                                    0x0

                # RTT On Additive Latency
                # PSU_DDR_PHY_DX3GCR0_RTTOAL                                                      0x0

                # RTT Output Hold
                # PSU_DDR_PHY_DX3GCR0_RTTOH                                                       0x3

                # Configurable PDR Phase Shift
                # PSU_DDR_PHY_DX3GCR0_CPDRSHFT                                                    0x0

                # DQSR Power Down
                # PSU_DDR_PHY_DX3GCR0_DQSRPD                                                      0x0

                # DQSG Power Down Receiver
                # PSU_DDR_PHY_DX3GCR0_DQSGPDR                                                     0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX3GCR0_RESERVED_4                                                  0x0

                # DQSG On-Die Termination
                # PSU_DDR_PHY_DX3GCR0_DQSGODT                                                     0x0

                # DQSG Output Enable
                # PSU_DDR_PHY_DX3GCR0_DQSGOE                                                      0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX3GCR0_RESERVED_1_0                                                0x0

                # DATX8 n General Configuration Register 0
                #(OFFSET, MASK, VALUE)      (0XFD080A00, 0xFFFFFFFFU ,0x40800604U)  */
    mask_write 0XFD080A00 0xFFFFFFFF 0x40800604
                # Register : DX3GCR1 @ 0XFD080A04</p>

                # Enables the PDR mode for DQ[7:0]
                # PSU_DDR_PHY_DX3GCR1_DXPDRMODE                                                   0x0

                # Reserved. Returns zeroes on reads.
                # PSU_DDR_PHY_DX3GCR1_RESERVED_15                                                 0x0

                # Select the delayed or non-delayed read data strobe #
                # PSU_DDR_PHY_DX3GCR1_QSNSEL                                                      0x1

                # Select the delayed or non-delayed read data strobe
                # PSU_DDR_PHY_DX3GCR1_QSSEL                                                       0x1

                # Enables Read Data Strobe in a byte lane
                # PSU_DDR_PHY_DX3GCR1_OEEN                                                        0x1

                # Enables PDR in a byte lane
                # PSU_DDR_PHY_DX3GCR1_PDREN                                                       0x1

                # Enables ODT/TE in a byte lane
                # PSU_DDR_PHY_DX3GCR1_TEEN                                                        0x1

                # Enables Write Data strobe in a byte lane
                # PSU_DDR_PHY_DX3GCR1_DSEN                                                        0x1

                # Enables DM pin in a byte lane
                # PSU_DDR_PHY_DX3GCR1_DMEN                                                        0x1

                # Enables DQ corresponding to each bit in a byte
                # PSU_DDR_PHY_DX3GCR1_DQEN                                                        0xff

                # DATX8 n General Configuration Register 1
                #(OFFSET, MASK, VALUE)      (0XFD080A04, 0xFFFFFFFFU ,0x00007FFFU)  */
    mask_write 0XFD080A04 0xFFFFFFFF 0x00007FFF
                # Register : DX3GCR4 @ 0XFD080A10</p>

                # Byte lane VREF IOM (Used only by D4MU IOs)
                # PSU_DDR_PHY_DX3GCR4_RESERVED_31_29                                              0x0

                # Byte Lane VREF Pad Enable
                # PSU_DDR_PHY_DX3GCR4_DXREFPEN                                                    0x0

                # Byte Lane Internal VREF Enable
                # PSU_DDR_PHY_DX3GCR4_DXREFEEN                                                    0x3

                # Byte Lane Single-End VREF Enable
                # PSU_DDR_PHY_DX3GCR4_DXREFSEN                                                    0x1

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX3GCR4_RESERVED_24                                                 0x0

                # External VREF generator REFSEL range select
                # PSU_DDR_PHY_DX3GCR4_DXREFESELRANGE                                              0x0

                # Byte Lane External VREF Select
                # PSU_DDR_PHY_DX3GCR4_DXREFESEL                                                   0x0

                # Single ended VREF generator REFSEL range select
                # PSU_DDR_PHY_DX3GCR4_DXREFSSELRANGE                                              0x1

                # Byte Lane Single-End VREF Select
                # PSU_DDR_PHY_DX3GCR4_DXREFSSEL                                                   0x30

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX3GCR4_RESERVED_7_6                                                0x0

                # VREF Enable control for DQ IO (Single Ended) buffers of a byte lane.
                # PSU_DDR_PHY_DX3GCR4_DXREFIEN                                                    0xf

                # VRMON control for DQ IO (Single Ended) buffers of a byte lane.
                # PSU_DDR_PHY_DX3GCR4_DXREFIMON                                                   0x0

                # DATX8 n General Configuration Register 4
                #(OFFSET, MASK, VALUE)      (0XFD080A10, 0xFFFFFFFFU ,0x0E00B03CU)  */
    mask_write 0XFD080A10 0xFFFFFFFF 0x0E00B03C
                # Register : DX3GCR5 @ 0XFD080A14</p>

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX3GCR5_RESERVED_31                                                 0x0

                # Byte Lane internal VREF Select for Rank 3
                # PSU_DDR_PHY_DX3GCR5_DXREFISELR3                                                 0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX3GCR5_RESERVED_23                                                 0x0

                # Byte Lane internal VREF Select for Rank 2
                # PSU_DDR_PHY_DX3GCR5_DXREFISELR2                                                 0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX3GCR5_RESERVED_15                                                 0x0

                # Byte Lane internal VREF Select for Rank 1
                # PSU_DDR_PHY_DX3GCR5_DXREFISELR1                                                 0x55

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX3GCR5_RESERVED_7                                                  0x0

                # Byte Lane internal VREF Select for Rank 0
                # PSU_DDR_PHY_DX3GCR5_DXREFISELR0                                                 0x55

                # DATX8 n General Configuration Register 5
                #(OFFSET, MASK, VALUE)      (0XFD080A14, 0xFFFFFFFFU ,0x09095555U)  */
    mask_write 0XFD080A14 0xFFFFFFFF 0x09095555
                # Register : DX3GCR6 @ 0XFD080A18</p>

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX3GCR6_RESERVED_31_30                                              0x0

                # DRAM DQ VREF Select for Rank3
                # PSU_DDR_PHY_DX3GCR6_DXDQVREFR3                                                  0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX3GCR6_RESERVED_23_22                                              0x0

                # DRAM DQ VREF Select for Rank2
                # PSU_DDR_PHY_DX3GCR6_DXDQVREFR2                                                  0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX3GCR6_RESERVED_15_14                                              0x0

                # DRAM DQ VREF Select for Rank1
                # PSU_DDR_PHY_DX3GCR6_DXDQVREFR1                                                  0x2b

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX3GCR6_RESERVED_7_6                                                0x0

                # DRAM DQ VREF Select for Rank0
                # PSU_DDR_PHY_DX3GCR6_DXDQVREFR0                                                  0x2b

                # DATX8 n General Configuration Register 6
                #(OFFSET, MASK, VALUE)      (0XFD080A18, 0xFFFFFFFFU ,0x09092B2BU)  */
    mask_write 0XFD080A18 0xFFFFFFFF 0x09092B2B
                # Register : DX3LCDLR2 @ 0XFD080A88</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX3LCDLR2_RESERVED_31_25                                            0x0

                # Reserved. Caution, do not write to this register field.
                # PSU_DDR_PHY_DX3LCDLR2_RESERVED_24_16                                            0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX3LCDLR2_RESERVED_15_9                                             0x0

                # Read DQS Gating Delay
                # PSU_DDR_PHY_DX3LCDLR2_DQSGD                                                     0x0

                # DATX8 n Local Calibrated Delay Line Register 2
                #(OFFSET, MASK, VALUE)      (0XFD080A88, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD080A88 0xFFFFFFFF 0x00000000
                # Register : DX3GTR0 @ 0XFD080AC0</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX3GTR0_RESERVED_31_24                                              0x0

                # DQ Write Path Latency Pipeline
                # PSU_DDR_PHY_DX3GTR0_WDQSL                                                       0x0

                # Reserved. Caution, do not write to this register field.
                # PSU_DDR_PHY_DX3GTR0_RESERVED_23_20                                              0x0

                # Write Leveling System Latency
                # PSU_DDR_PHY_DX3GTR0_WLSL                                                        0x2

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX3GTR0_RESERVED_15_13                                              0x0

                # Reserved. Caution, do not write to this register field.
                # PSU_DDR_PHY_DX3GTR0_RESERVED_12_8                                               0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX3GTR0_RESERVED_7_5                                                0x0

                # DQS Gating System Latency
                # PSU_DDR_PHY_DX3GTR0_DGSL                                                        0x0

                # DATX8 n General Timing Register 0
                #(OFFSET, MASK, VALUE)      (0XFD080AC0, 0xFFFFFFFFU ,0x00020000U)  */
    mask_write 0XFD080AC0 0xFFFFFFFF 0x00020000
                # Register : DX4GCR0 @ 0XFD080B00</p>

                # Calibration Bypass
                # PSU_DDR_PHY_DX4GCR0_CALBYP                                                      0x0

                # Master Delay Line Enable
                # PSU_DDR_PHY_DX4GCR0_MDLEN                                                       0x1

                # Configurable ODT(TE) Phase Shift
                # PSU_DDR_PHY_DX4GCR0_CODTSHFT                                                    0x0

                # DQS Duty Cycle Correction
                # PSU_DDR_PHY_DX4GCR0_DQSDCC                                                      0x0

                # Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd input for the respective bypte lane of the PHY
                # PSU_DDR_PHY_DX4GCR0_RDDLY                                                       0x8

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX4GCR0_RESERVED_19_14                                              0x0

                # DQSNSE Power Down Receiver
                # PSU_DDR_PHY_DX4GCR0_DQSNSEPDR                                                   0x0

                # DQSSE Power Down Receiver
                # PSU_DDR_PHY_DX4GCR0_DQSSEPDR                                                    0x0

                # RTT On Additive Latency
                # PSU_DDR_PHY_DX4GCR0_RTTOAL                                                      0x0

                # RTT Output Hold
                # PSU_DDR_PHY_DX4GCR0_RTTOH                                                       0x3

                # Configurable PDR Phase Shift
                # PSU_DDR_PHY_DX4GCR0_CPDRSHFT                                                    0x0

                # DQSR Power Down
                # PSU_DDR_PHY_DX4GCR0_DQSRPD                                                      0x0

                # DQSG Power Down Receiver
                # PSU_DDR_PHY_DX4GCR0_DQSGPDR                                                     0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX4GCR0_RESERVED_4                                                  0x0

                # DQSG On-Die Termination
                # PSU_DDR_PHY_DX4GCR0_DQSGODT                                                     0x0

                # DQSG Output Enable
                # PSU_DDR_PHY_DX4GCR0_DQSGOE                                                      0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX4GCR0_RESERVED_1_0                                                0x0

                # DATX8 n General Configuration Register 0
                #(OFFSET, MASK, VALUE)      (0XFD080B00, 0xFFFFFFFFU ,0x40800604U)  */
    mask_write 0XFD080B00 0xFFFFFFFF 0x40800604
                # Register : DX4GCR1 @ 0XFD080B04</p>

                # Enables the PDR mode for DQ[7:0]
                # PSU_DDR_PHY_DX4GCR1_DXPDRMODE                                                   0x0

                # Reserved. Returns zeroes on reads.
                # PSU_DDR_PHY_DX4GCR1_RESERVED_15                                                 0x0

                # Select the delayed or non-delayed read data strobe #
                # PSU_DDR_PHY_DX4GCR1_QSNSEL                                                      0x1

                # Select the delayed or non-delayed read data strobe
                # PSU_DDR_PHY_DX4GCR1_QSSEL                                                       0x1

                # Enables Read Data Strobe in a byte lane
                # PSU_DDR_PHY_DX4GCR1_OEEN                                                        0x1

                # Enables PDR in a byte lane
                # PSU_DDR_PHY_DX4GCR1_PDREN                                                       0x1

                # Enables ODT/TE in a byte lane
                # PSU_DDR_PHY_DX4GCR1_TEEN                                                        0x1

                # Enables Write Data strobe in a byte lane
                # PSU_DDR_PHY_DX4GCR1_DSEN                                                        0x1

                # Enables DM pin in a byte lane
                # PSU_DDR_PHY_DX4GCR1_DMEN                                                        0x1

                # Enables DQ corresponding to each bit in a byte
                # PSU_DDR_PHY_DX4GCR1_DQEN                                                        0xff

                # DATX8 n General Configuration Register 1
                #(OFFSET, MASK, VALUE)      (0XFD080B04, 0xFFFFFFFFU ,0x00007FFFU)  */
    mask_write 0XFD080B04 0xFFFFFFFF 0x00007FFF
                # Register : DX4GCR4 @ 0XFD080B10</p>

                # Byte lane VREF IOM (Used only by D4MU IOs)
                # PSU_DDR_PHY_DX4GCR4_RESERVED_31_29                                              0x0

                # Byte Lane VREF Pad Enable
                # PSU_DDR_PHY_DX4GCR4_DXREFPEN                                                    0x0

                # Byte Lane Internal VREF Enable
                # PSU_DDR_PHY_DX4GCR4_DXREFEEN                                                    0x3

                # Byte Lane Single-End VREF Enable
                # PSU_DDR_PHY_DX4GCR4_DXREFSEN                                                    0x1

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX4GCR4_RESERVED_24                                                 0x0

                # External VREF generator REFSEL range select
                # PSU_DDR_PHY_DX4GCR4_DXREFESELRANGE                                              0x0

                # Byte Lane External VREF Select
                # PSU_DDR_PHY_DX4GCR4_DXREFESEL                                                   0x0

                # Single ended VREF generator REFSEL range select
                # PSU_DDR_PHY_DX4GCR4_DXREFSSELRANGE                                              0x1

                # Byte Lane Single-End VREF Select
                # PSU_DDR_PHY_DX4GCR4_DXREFSSEL                                                   0x30

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX4GCR4_RESERVED_7_6                                                0x0

                # VREF Enable control for DQ IO (Single Ended) buffers of a byte lane.
                # PSU_DDR_PHY_DX4GCR4_DXREFIEN                                                    0xf

                # VRMON control for DQ IO (Single Ended) buffers of a byte lane.
                # PSU_DDR_PHY_DX4GCR4_DXREFIMON                                                   0x0

                # DATX8 n General Configuration Register 4
                #(OFFSET, MASK, VALUE)      (0XFD080B10, 0xFFFFFFFFU ,0x0E00B03CU)  */
    mask_write 0XFD080B10 0xFFFFFFFF 0x0E00B03C
                # Register : DX4GCR5 @ 0XFD080B14</p>

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX4GCR5_RESERVED_31                                                 0x0

                # Byte Lane internal VREF Select for Rank 3
                # PSU_DDR_PHY_DX4GCR5_DXREFISELR3                                                 0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX4GCR5_RESERVED_23                                                 0x0

                # Byte Lane internal VREF Select for Rank 2
                # PSU_DDR_PHY_DX4GCR5_DXREFISELR2                                                 0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX4GCR5_RESERVED_15                                                 0x0

                # Byte Lane internal VREF Select for Rank 1
                # PSU_DDR_PHY_DX4GCR5_DXREFISELR1                                                 0x55

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX4GCR5_RESERVED_7                                                  0x0

                # Byte Lane internal VREF Select for Rank 0
                # PSU_DDR_PHY_DX4GCR5_DXREFISELR0                                                 0x55

                # DATX8 n General Configuration Register 5
                #(OFFSET, MASK, VALUE)      (0XFD080B14, 0xFFFFFFFFU ,0x09095555U)  */
    mask_write 0XFD080B14 0xFFFFFFFF 0x09095555
                # Register : DX4GCR6 @ 0XFD080B18</p>

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX4GCR6_RESERVED_31_30                                              0x0

                # DRAM DQ VREF Select for Rank3
                # PSU_DDR_PHY_DX4GCR6_DXDQVREFR3                                                  0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX4GCR6_RESERVED_23_22                                              0x0

                # DRAM DQ VREF Select for Rank2
                # PSU_DDR_PHY_DX4GCR6_DXDQVREFR2                                                  0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX4GCR6_RESERVED_15_14                                              0x0

                # DRAM DQ VREF Select for Rank1
                # PSU_DDR_PHY_DX4GCR6_DXDQVREFR1                                                  0x2b

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX4GCR6_RESERVED_7_6                                                0x0

                # DRAM DQ VREF Select for Rank0
                # PSU_DDR_PHY_DX4GCR6_DXDQVREFR0                                                  0x2b

                # DATX8 n General Configuration Register 6
                #(OFFSET, MASK, VALUE)      (0XFD080B18, 0xFFFFFFFFU ,0x09092B2BU)  */
    mask_write 0XFD080B18 0xFFFFFFFF 0x09092B2B
                # Register : DX4LCDLR2 @ 0XFD080B88</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX4LCDLR2_RESERVED_31_25                                            0x0

                # Reserved. Caution, do not write to this register field.
                # PSU_DDR_PHY_DX4LCDLR2_RESERVED_24_16                                            0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX4LCDLR2_RESERVED_15_9                                             0x0

                # Read DQS Gating Delay
                # PSU_DDR_PHY_DX4LCDLR2_DQSGD                                                     0x0

                # DATX8 n Local Calibrated Delay Line Register 2
                #(OFFSET, MASK, VALUE)      (0XFD080B88, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD080B88 0xFFFFFFFF 0x00000000
                # Register : DX4GTR0 @ 0XFD080BC0</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX4GTR0_RESERVED_31_24                                              0x0

                # DQ Write Path Latency Pipeline
                # PSU_DDR_PHY_DX4GTR0_WDQSL                                                       0x0

                # Reserved. Caution, do not write to this register field.
                # PSU_DDR_PHY_DX4GTR0_RESERVED_23_20                                              0x0

                # Write Leveling System Latency
                # PSU_DDR_PHY_DX4GTR0_WLSL                                                        0x2

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX4GTR0_RESERVED_15_13                                              0x0

                # Reserved. Caution, do not write to this register field.
                # PSU_DDR_PHY_DX4GTR0_RESERVED_12_8                                               0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX4GTR0_RESERVED_7_5                                                0x0

                # DQS Gating System Latency
                # PSU_DDR_PHY_DX4GTR0_DGSL                                                        0x0

                # DATX8 n General Timing Register 0
                #(OFFSET, MASK, VALUE)      (0XFD080BC0, 0xFFFFFFFFU ,0x00020000U)  */
    mask_write 0XFD080BC0 0xFFFFFFFF 0x00020000
                # Register : DX5GCR0 @ 0XFD080C00</p>

                # Calibration Bypass
                # PSU_DDR_PHY_DX5GCR0_CALBYP                                                      0x0

                # Master Delay Line Enable
                # PSU_DDR_PHY_DX5GCR0_MDLEN                                                       0x1

                # Configurable ODT(TE) Phase Shift
                # PSU_DDR_PHY_DX5GCR0_CODTSHFT                                                    0x0

                # DQS Duty Cycle Correction
                # PSU_DDR_PHY_DX5GCR0_DQSDCC                                                      0x0

                # Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd input for the respective bypte lane of the PHY
                # PSU_DDR_PHY_DX5GCR0_RDDLY                                                       0x8

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX5GCR0_RESERVED_19_14                                              0x0

                # DQSNSE Power Down Receiver
                # PSU_DDR_PHY_DX5GCR0_DQSNSEPDR                                                   0x0

                # DQSSE Power Down Receiver
                # PSU_DDR_PHY_DX5GCR0_DQSSEPDR                                                    0x0

                # RTT On Additive Latency
                # PSU_DDR_PHY_DX5GCR0_RTTOAL                                                      0x0

                # RTT Output Hold
                # PSU_DDR_PHY_DX5GCR0_RTTOH                                                       0x3

                # Configurable PDR Phase Shift
                # PSU_DDR_PHY_DX5GCR0_CPDRSHFT                                                    0x0

                # DQSR Power Down
                # PSU_DDR_PHY_DX5GCR0_DQSRPD                                                      0x0

                # DQSG Power Down Receiver
                # PSU_DDR_PHY_DX5GCR0_DQSGPDR                                                     0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX5GCR0_RESERVED_4                                                  0x0

                # DQSG On-Die Termination
                # PSU_DDR_PHY_DX5GCR0_DQSGODT                                                     0x0

                # DQSG Output Enable
                # PSU_DDR_PHY_DX5GCR0_DQSGOE                                                      0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX5GCR0_RESERVED_1_0                                                0x0

                # DATX8 n General Configuration Register 0
                #(OFFSET, MASK, VALUE)      (0XFD080C00, 0xFFFFFFFFU ,0x40800604U)  */
    mask_write 0XFD080C00 0xFFFFFFFF 0x40800604
                # Register : DX5GCR1 @ 0XFD080C04</p>

                # Enables the PDR mode for DQ[7:0]
                # PSU_DDR_PHY_DX5GCR1_DXPDRMODE                                                   0x0

                # Reserved. Returns zeroes on reads.
                # PSU_DDR_PHY_DX5GCR1_RESERVED_15                                                 0x0

                # Select the delayed or non-delayed read data strobe #
                # PSU_DDR_PHY_DX5GCR1_QSNSEL                                                      0x1

                # Select the delayed or non-delayed read data strobe
                # PSU_DDR_PHY_DX5GCR1_QSSEL                                                       0x1

                # Enables Read Data Strobe in a byte lane
                # PSU_DDR_PHY_DX5GCR1_OEEN                                                        0x1

                # Enables PDR in a byte lane
                # PSU_DDR_PHY_DX5GCR1_PDREN                                                       0x1

                # Enables ODT/TE in a byte lane
                # PSU_DDR_PHY_DX5GCR1_TEEN                                                        0x1

                # Enables Write Data strobe in a byte lane
                # PSU_DDR_PHY_DX5GCR1_DSEN                                                        0x1

                # Enables DM pin in a byte lane
                # PSU_DDR_PHY_DX5GCR1_DMEN                                                        0x1

                # Enables DQ corresponding to each bit in a byte
                # PSU_DDR_PHY_DX5GCR1_DQEN                                                        0xff

                # DATX8 n General Configuration Register 1
                #(OFFSET, MASK, VALUE)      (0XFD080C04, 0xFFFFFFFFU ,0x00007FFFU)  */
    mask_write 0XFD080C04 0xFFFFFFFF 0x00007FFF
                # Register : DX5GCR4 @ 0XFD080C10</p>

                # Byte lane VREF IOM (Used only by D4MU IOs)
                # PSU_DDR_PHY_DX5GCR4_RESERVED_31_29                                              0x0

                # Byte Lane VREF Pad Enable
                # PSU_DDR_PHY_DX5GCR4_DXREFPEN                                                    0x0

                # Byte Lane Internal VREF Enable
                # PSU_DDR_PHY_DX5GCR4_DXREFEEN                                                    0x3

                # Byte Lane Single-End VREF Enable
                # PSU_DDR_PHY_DX5GCR4_DXREFSEN                                                    0x1

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX5GCR4_RESERVED_24                                                 0x0

                # External VREF generator REFSEL range select
                # PSU_DDR_PHY_DX5GCR4_DXREFESELRANGE                                              0x0

                # Byte Lane External VREF Select
                # PSU_DDR_PHY_DX5GCR4_DXREFESEL                                                   0x0

                # Single ended VREF generator REFSEL range select
                # PSU_DDR_PHY_DX5GCR4_DXREFSSELRANGE                                              0x1

                # Byte Lane Single-End VREF Select
                # PSU_DDR_PHY_DX5GCR4_DXREFSSEL                                                   0x30

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX5GCR4_RESERVED_7_6                                                0x0

                # VREF Enable control for DQ IO (Single Ended) buffers of a byte lane.
                # PSU_DDR_PHY_DX5GCR4_DXREFIEN                                                    0xf

                # VRMON control for DQ IO (Single Ended) buffers of a byte lane.
                # PSU_DDR_PHY_DX5GCR4_DXREFIMON                                                   0x0

                # DATX8 n General Configuration Register 4
                #(OFFSET, MASK, VALUE)      (0XFD080C10, 0xFFFFFFFFU ,0x0E00B03CU)  */
    mask_write 0XFD080C10 0xFFFFFFFF 0x0E00B03C
                # Register : DX5GCR5 @ 0XFD080C14</p>

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX5GCR5_RESERVED_31                                                 0x0

                # Byte Lane internal VREF Select for Rank 3
                # PSU_DDR_PHY_DX5GCR5_DXREFISELR3                                                 0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX5GCR5_RESERVED_23                                                 0x0

                # Byte Lane internal VREF Select for Rank 2
                # PSU_DDR_PHY_DX5GCR5_DXREFISELR2                                                 0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX5GCR5_RESERVED_15                                                 0x0

                # Byte Lane internal VREF Select for Rank 1
                # PSU_DDR_PHY_DX5GCR5_DXREFISELR1                                                 0x55

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX5GCR5_RESERVED_7                                                  0x0

                # Byte Lane internal VREF Select for Rank 0
                # PSU_DDR_PHY_DX5GCR5_DXREFISELR0                                                 0x55

                # DATX8 n General Configuration Register 5
                #(OFFSET, MASK, VALUE)      (0XFD080C14, 0xFFFFFFFFU ,0x09095555U)  */
    mask_write 0XFD080C14 0xFFFFFFFF 0x09095555
                # Register : DX5GCR6 @ 0XFD080C18</p>

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX5GCR6_RESERVED_31_30                                              0x0

                # DRAM DQ VREF Select for Rank3
                # PSU_DDR_PHY_DX5GCR6_DXDQVREFR3                                                  0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX5GCR6_RESERVED_23_22                                              0x0

                # DRAM DQ VREF Select for Rank2
                # PSU_DDR_PHY_DX5GCR6_DXDQVREFR2                                                  0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX5GCR6_RESERVED_15_14                                              0x0

                # DRAM DQ VREF Select for Rank1
                # PSU_DDR_PHY_DX5GCR6_DXDQVREFR1                                                  0x2b

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX5GCR6_RESERVED_7_6                                                0x0

                # DRAM DQ VREF Select for Rank0
                # PSU_DDR_PHY_DX5GCR6_DXDQVREFR0                                                  0x2b

                # DATX8 n General Configuration Register 6
                #(OFFSET, MASK, VALUE)      (0XFD080C18, 0xFFFFFFFFU ,0x09092B2BU)  */
    mask_write 0XFD080C18 0xFFFFFFFF 0x09092B2B
                # Register : DX5LCDLR2 @ 0XFD080C88</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX5LCDLR2_RESERVED_31_25                                            0x0

                # Reserved. Caution, do not write to this register field.
                # PSU_DDR_PHY_DX5LCDLR2_RESERVED_24_16                                            0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX5LCDLR2_RESERVED_15_9                                             0x0

                # Read DQS Gating Delay
                # PSU_DDR_PHY_DX5LCDLR2_DQSGD                                                     0x0

                # DATX8 n Local Calibrated Delay Line Register 2
                #(OFFSET, MASK, VALUE)      (0XFD080C88, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD080C88 0xFFFFFFFF 0x00000000
                # Register : DX5GTR0 @ 0XFD080CC0</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX5GTR0_RESERVED_31_24                                              0x0

                # DQ Write Path Latency Pipeline
                # PSU_DDR_PHY_DX5GTR0_WDQSL                                                       0x0

                # Reserved. Caution, do not write to this register field.
                # PSU_DDR_PHY_DX5GTR0_RESERVED_23_20                                              0x0

                # Write Leveling System Latency
                # PSU_DDR_PHY_DX5GTR0_WLSL                                                        0x2

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX5GTR0_RESERVED_15_13                                              0x0

                # Reserved. Caution, do not write to this register field.
                # PSU_DDR_PHY_DX5GTR0_RESERVED_12_8                                               0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX5GTR0_RESERVED_7_5                                                0x0

                # DQS Gating System Latency
                # PSU_DDR_PHY_DX5GTR0_DGSL                                                        0x0

                # DATX8 n General Timing Register 0
                #(OFFSET, MASK, VALUE)      (0XFD080CC0, 0xFFFFFFFFU ,0x00020000U)  */
    mask_write 0XFD080CC0 0xFFFFFFFF 0x00020000
                # Register : DX6GCR0 @ 0XFD080D00</p>

                # Calibration Bypass
                # PSU_DDR_PHY_DX6GCR0_CALBYP                                                      0x0

                # Master Delay Line Enable
                # PSU_DDR_PHY_DX6GCR0_MDLEN                                                       0x1

                # Configurable ODT(TE) Phase Shift
                # PSU_DDR_PHY_DX6GCR0_CODTSHFT                                                    0x0

                # DQS Duty Cycle Correction
                # PSU_DDR_PHY_DX6GCR0_DQSDCC                                                      0x0

                # Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd input for the respective bypte lane of the PHY
                # PSU_DDR_PHY_DX6GCR0_RDDLY                                                       0x8

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX6GCR0_RESERVED_19_14                                              0x0

                # DQSNSE Power Down Receiver
                # PSU_DDR_PHY_DX6GCR0_DQSNSEPDR                                                   0x0

                # DQSSE Power Down Receiver
                # PSU_DDR_PHY_DX6GCR0_DQSSEPDR                                                    0x0

                # RTT On Additive Latency
                # PSU_DDR_PHY_DX6GCR0_RTTOAL                                                      0x0

                # RTT Output Hold
                # PSU_DDR_PHY_DX6GCR0_RTTOH                                                       0x3

                # Configurable PDR Phase Shift
                # PSU_DDR_PHY_DX6GCR0_CPDRSHFT                                                    0x0

                # DQSR Power Down
                # PSU_DDR_PHY_DX6GCR0_DQSRPD                                                      0x0

                # DQSG Power Down Receiver
                # PSU_DDR_PHY_DX6GCR0_DQSGPDR                                                     0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX6GCR0_RESERVED_4                                                  0x0

                # DQSG On-Die Termination
                # PSU_DDR_PHY_DX6GCR0_DQSGODT                                                     0x0

                # DQSG Output Enable
                # PSU_DDR_PHY_DX6GCR0_DQSGOE                                                      0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX6GCR0_RESERVED_1_0                                                0x0

                # DATX8 n General Configuration Register 0
                #(OFFSET, MASK, VALUE)      (0XFD080D00, 0xFFFFFFFFU ,0x40800604U)  */
    mask_write 0XFD080D00 0xFFFFFFFF 0x40800604
                # Register : DX6GCR1 @ 0XFD080D04</p>

                # Enables the PDR mode for DQ[7:0]
                # PSU_DDR_PHY_DX6GCR1_DXPDRMODE                                                   0x0

                # Reserved. Returns zeroes on reads.
                # PSU_DDR_PHY_DX6GCR1_RESERVED_15                                                 0x0

                # Select the delayed or non-delayed read data strobe #
                # PSU_DDR_PHY_DX6GCR1_QSNSEL                                                      0x1

                # Select the delayed or non-delayed read data strobe
                # PSU_DDR_PHY_DX6GCR1_QSSEL                                                       0x1

                # Enables Read Data Strobe in a byte lane
                # PSU_DDR_PHY_DX6GCR1_OEEN                                                        0x1

                # Enables PDR in a byte lane
                # PSU_DDR_PHY_DX6GCR1_PDREN                                                       0x1

                # Enables ODT/TE in a byte lane
                # PSU_DDR_PHY_DX6GCR1_TEEN                                                        0x1

                # Enables Write Data strobe in a byte lane
                # PSU_DDR_PHY_DX6GCR1_DSEN                                                        0x1

                # Enables DM pin in a byte lane
                # PSU_DDR_PHY_DX6GCR1_DMEN                                                        0x1

                # Enables DQ corresponding to each bit in a byte
                # PSU_DDR_PHY_DX6GCR1_DQEN                                                        0xff

                # DATX8 n General Configuration Register 1
                #(OFFSET, MASK, VALUE)      (0XFD080D04, 0xFFFFFFFFU ,0x00007FFFU)  */
    mask_write 0XFD080D04 0xFFFFFFFF 0x00007FFF
                # Register : DX6GCR4 @ 0XFD080D10</p>

                # Byte lane VREF IOM (Used only by D4MU IOs)
                # PSU_DDR_PHY_DX6GCR4_RESERVED_31_29                                              0x0

                # Byte Lane VREF Pad Enable
                # PSU_DDR_PHY_DX6GCR4_DXREFPEN                                                    0x0

                # Byte Lane Internal VREF Enable
                # PSU_DDR_PHY_DX6GCR4_DXREFEEN                                                    0x3

                # Byte Lane Single-End VREF Enable
                # PSU_DDR_PHY_DX6GCR4_DXREFSEN                                                    0x1

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX6GCR4_RESERVED_24                                                 0x0

                # External VREF generator REFSEL range select
                # PSU_DDR_PHY_DX6GCR4_DXREFESELRANGE                                              0x0

                # Byte Lane External VREF Select
                # PSU_DDR_PHY_DX6GCR4_DXREFESEL                                                   0x0

                # Single ended VREF generator REFSEL range select
                # PSU_DDR_PHY_DX6GCR4_DXREFSSELRANGE                                              0x1

                # Byte Lane Single-End VREF Select
                # PSU_DDR_PHY_DX6GCR4_DXREFSSEL                                                   0x30

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX6GCR4_RESERVED_7_6                                                0x0

                # VREF Enable control for DQ IO (Single Ended) buffers of a byte lane.
                # PSU_DDR_PHY_DX6GCR4_DXREFIEN                                                    0xf

                # VRMON control for DQ IO (Single Ended) buffers of a byte lane.
                # PSU_DDR_PHY_DX6GCR4_DXREFIMON                                                   0x0

                # DATX8 n General Configuration Register 4
                #(OFFSET, MASK, VALUE)      (0XFD080D10, 0xFFFFFFFFU ,0x0E00B03CU)  */
    mask_write 0XFD080D10 0xFFFFFFFF 0x0E00B03C
                # Register : DX6GCR5 @ 0XFD080D14</p>

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX6GCR5_RESERVED_31                                                 0x0

                # Byte Lane internal VREF Select for Rank 3
                # PSU_DDR_PHY_DX6GCR5_DXREFISELR3                                                 0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX6GCR5_RESERVED_23                                                 0x0

                # Byte Lane internal VREF Select for Rank 2
                # PSU_DDR_PHY_DX6GCR5_DXREFISELR2                                                 0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX6GCR5_RESERVED_15                                                 0x0

                # Byte Lane internal VREF Select for Rank 1
                # PSU_DDR_PHY_DX6GCR5_DXREFISELR1                                                 0x55

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX6GCR5_RESERVED_7                                                  0x0

                # Byte Lane internal VREF Select for Rank 0
                # PSU_DDR_PHY_DX6GCR5_DXREFISELR0                                                 0x55

                # DATX8 n General Configuration Register 5
                #(OFFSET, MASK, VALUE)      (0XFD080D14, 0xFFFFFFFFU ,0x09095555U)  */
    mask_write 0XFD080D14 0xFFFFFFFF 0x09095555
                # Register : DX6GCR6 @ 0XFD080D18</p>

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX6GCR6_RESERVED_31_30                                              0x0

                # DRAM DQ VREF Select for Rank3
                # PSU_DDR_PHY_DX6GCR6_DXDQVREFR3                                                  0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX6GCR6_RESERVED_23_22                                              0x0

                # DRAM DQ VREF Select for Rank2
                # PSU_DDR_PHY_DX6GCR6_DXDQVREFR2                                                  0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX6GCR6_RESERVED_15_14                                              0x0

                # DRAM DQ VREF Select for Rank1
                # PSU_DDR_PHY_DX6GCR6_DXDQVREFR1                                                  0x2b

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX6GCR6_RESERVED_7_6                                                0x0

                # DRAM DQ VREF Select for Rank0
                # PSU_DDR_PHY_DX6GCR6_DXDQVREFR0                                                  0x2b

                # DATX8 n General Configuration Register 6
                #(OFFSET, MASK, VALUE)      (0XFD080D18, 0xFFFFFFFFU ,0x09092B2BU)  */
    mask_write 0XFD080D18 0xFFFFFFFF 0x09092B2B
                # Register : DX6LCDLR2 @ 0XFD080D88</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX6LCDLR2_RESERVED_31_25                                            0x0

                # Reserved. Caution, do not write to this register field.
                # PSU_DDR_PHY_DX6LCDLR2_RESERVED_24_16                                            0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX6LCDLR2_RESERVED_15_9                                             0x0

                # Read DQS Gating Delay
                # PSU_DDR_PHY_DX6LCDLR2_DQSGD                                                     0x0

                # DATX8 n Local Calibrated Delay Line Register 2
                #(OFFSET, MASK, VALUE)      (0XFD080D88, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD080D88 0xFFFFFFFF 0x00000000
                # Register : DX6GTR0 @ 0XFD080DC0</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX6GTR0_RESERVED_31_24                                              0x0

                # DQ Write Path Latency Pipeline
                # PSU_DDR_PHY_DX6GTR0_WDQSL                                                       0x0

                # Reserved. Caution, do not write to this register field.
                # PSU_DDR_PHY_DX6GTR0_RESERVED_23_20                                              0x0

                # Write Leveling System Latency
                # PSU_DDR_PHY_DX6GTR0_WLSL                                                        0x2

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX6GTR0_RESERVED_15_13                                              0x0

                # Reserved. Caution, do not write to this register field.
                # PSU_DDR_PHY_DX6GTR0_RESERVED_12_8                                               0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX6GTR0_RESERVED_7_5                                                0x0

                # DQS Gating System Latency
                # PSU_DDR_PHY_DX6GTR0_DGSL                                                        0x0

                # DATX8 n General Timing Register 0
                #(OFFSET, MASK, VALUE)      (0XFD080DC0, 0xFFFFFFFFU ,0x00020000U)  */
    mask_write 0XFD080DC0 0xFFFFFFFF 0x00020000
                # Register : DX7GCR0 @ 0XFD080E00</p>

                # Calibration Bypass
                # PSU_DDR_PHY_DX7GCR0_CALBYP                                                      0x0

                # Master Delay Line Enable
                # PSU_DDR_PHY_DX7GCR0_MDLEN                                                       0x1

                # Configurable ODT(TE) Phase Shift
                # PSU_DDR_PHY_DX7GCR0_CODTSHFT                                                    0x0

                # DQS Duty Cycle Correction
                # PSU_DDR_PHY_DX7GCR0_DQSDCC                                                      0x0

                # Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd input for the respective bypte lane of the PHY
                # PSU_DDR_PHY_DX7GCR0_RDDLY                                                       0x8

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX7GCR0_RESERVED_19_14                                              0x0

                # DQSNSE Power Down Receiver
                # PSU_DDR_PHY_DX7GCR0_DQSNSEPDR                                                   0x0

                # DQSSE Power Down Receiver
                # PSU_DDR_PHY_DX7GCR0_DQSSEPDR                                                    0x0

                # RTT On Additive Latency
                # PSU_DDR_PHY_DX7GCR0_RTTOAL                                                      0x0

                # RTT Output Hold
                # PSU_DDR_PHY_DX7GCR0_RTTOH                                                       0x3

                # Configurable PDR Phase Shift
                # PSU_DDR_PHY_DX7GCR0_CPDRSHFT                                                    0x0

                # DQSR Power Down
                # PSU_DDR_PHY_DX7GCR0_DQSRPD                                                      0x0

                # DQSG Power Down Receiver
                # PSU_DDR_PHY_DX7GCR0_DQSGPDR                                                     0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX7GCR0_RESERVED_4                                                  0x0

                # DQSG On-Die Termination
                # PSU_DDR_PHY_DX7GCR0_DQSGODT                                                     0x0

                # DQSG Output Enable
                # PSU_DDR_PHY_DX7GCR0_DQSGOE                                                      0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX7GCR0_RESERVED_1_0                                                0x0

                # DATX8 n General Configuration Register 0
                #(OFFSET, MASK, VALUE)      (0XFD080E00, 0xFFFFFFFFU ,0x40800604U)  */
    mask_write 0XFD080E00 0xFFFFFFFF 0x40800604
                # Register : DX7GCR1 @ 0XFD080E04</p>

                # Enables the PDR mode for DQ[7:0]
                # PSU_DDR_PHY_DX7GCR1_DXPDRMODE                                                   0x0

                # Reserved. Returns zeroes on reads.
                # PSU_DDR_PHY_DX7GCR1_RESERVED_15                                                 0x0

                # Select the delayed or non-delayed read data strobe #
                # PSU_DDR_PHY_DX7GCR1_QSNSEL                                                      0x1

                # Select the delayed or non-delayed read data strobe
                # PSU_DDR_PHY_DX7GCR1_QSSEL                                                       0x1

                # Enables Read Data Strobe in a byte lane
                # PSU_DDR_PHY_DX7GCR1_OEEN                                                        0x1

                # Enables PDR in a byte lane
                # PSU_DDR_PHY_DX7GCR1_PDREN                                                       0x1

                # Enables ODT/TE in a byte lane
                # PSU_DDR_PHY_DX7GCR1_TEEN                                                        0x1

                # Enables Write Data strobe in a byte lane
                # PSU_DDR_PHY_DX7GCR1_DSEN                                                        0x1

                # Enables DM pin in a byte lane
                # PSU_DDR_PHY_DX7GCR1_DMEN                                                        0x1

                # Enables DQ corresponding to each bit in a byte
                # PSU_DDR_PHY_DX7GCR1_DQEN                                                        0xff

                # DATX8 n General Configuration Register 1
                #(OFFSET, MASK, VALUE)      (0XFD080E04, 0xFFFFFFFFU ,0x00007FFFU)  */
    mask_write 0XFD080E04 0xFFFFFFFF 0x00007FFF
                # Register : DX7GCR4 @ 0XFD080E10</p>

                # Byte lane VREF IOM (Used only by D4MU IOs)
                # PSU_DDR_PHY_DX7GCR4_RESERVED_31_29                                              0x0

                # Byte Lane VREF Pad Enable
                # PSU_DDR_PHY_DX7GCR4_DXREFPEN                                                    0x0

                # Byte Lane Internal VREF Enable
                # PSU_DDR_PHY_DX7GCR4_DXREFEEN                                                    0x3

                # Byte Lane Single-End VREF Enable
                # PSU_DDR_PHY_DX7GCR4_DXREFSEN                                                    0x1

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX7GCR4_RESERVED_24                                                 0x0

                # External VREF generator REFSEL range select
                # PSU_DDR_PHY_DX7GCR4_DXREFESELRANGE                                              0x0

                # Byte Lane External VREF Select
                # PSU_DDR_PHY_DX7GCR4_DXREFESEL                                                   0x0

                # Single ended VREF generator REFSEL range select
                # PSU_DDR_PHY_DX7GCR4_DXREFSSELRANGE                                              0x1

                # Byte Lane Single-End VREF Select
                # PSU_DDR_PHY_DX7GCR4_DXREFSSEL                                                   0x30

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX7GCR4_RESERVED_7_6                                                0x0

                # VREF Enable control for DQ IO (Single Ended) buffers of a byte lane.
                # PSU_DDR_PHY_DX7GCR4_DXREFIEN                                                    0xf

                # VRMON control for DQ IO (Single Ended) buffers of a byte lane.
                # PSU_DDR_PHY_DX7GCR4_DXREFIMON                                                   0x0

                # DATX8 n General Configuration Register 4
                #(OFFSET, MASK, VALUE)      (0XFD080E10, 0xFFFFFFFFU ,0x0E00B03CU)  */
    mask_write 0XFD080E10 0xFFFFFFFF 0x0E00B03C
                # Register : DX7GCR5 @ 0XFD080E14</p>

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX7GCR5_RESERVED_31                                                 0x0

                # Byte Lane internal VREF Select for Rank 3
                # PSU_DDR_PHY_DX7GCR5_DXREFISELR3                                                 0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX7GCR5_RESERVED_23                                                 0x0

                # Byte Lane internal VREF Select for Rank 2
                # PSU_DDR_PHY_DX7GCR5_DXREFISELR2                                                 0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX7GCR5_RESERVED_15                                                 0x0

                # Byte Lane internal VREF Select for Rank 1
                # PSU_DDR_PHY_DX7GCR5_DXREFISELR1                                                 0x55

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX7GCR5_RESERVED_7                                                  0x0

                # Byte Lane internal VREF Select for Rank 0
                # PSU_DDR_PHY_DX7GCR5_DXREFISELR0                                                 0x55

                # DATX8 n General Configuration Register 5
                #(OFFSET, MASK, VALUE)      (0XFD080E14, 0xFFFFFFFFU ,0x09095555U)  */
    mask_write 0XFD080E14 0xFFFFFFFF 0x09095555
                # Register : DX7GCR6 @ 0XFD080E18</p>

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX7GCR6_RESERVED_31_30                                              0x0

                # DRAM DQ VREF Select for Rank3
                # PSU_DDR_PHY_DX7GCR6_DXDQVREFR3                                                  0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX7GCR6_RESERVED_23_22                                              0x0

                # DRAM DQ VREF Select for Rank2
                # PSU_DDR_PHY_DX7GCR6_DXDQVREFR2                                                  0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX7GCR6_RESERVED_15_14                                              0x0

                # DRAM DQ VREF Select for Rank1
                # PSU_DDR_PHY_DX7GCR6_DXDQVREFR1                                                  0x2b

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX7GCR6_RESERVED_7_6                                                0x0

                # DRAM DQ VREF Select for Rank0
                # PSU_DDR_PHY_DX7GCR6_DXDQVREFR0                                                  0x2b

                # DATX8 n General Configuration Register 6
                #(OFFSET, MASK, VALUE)      (0XFD080E18, 0xFFFFFFFFU ,0x09092B2BU)  */
    mask_write 0XFD080E18 0xFFFFFFFF 0x09092B2B
                # Register : DX7LCDLR2 @ 0XFD080E88</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX7LCDLR2_RESERVED_31_25                                            0x0

                # Reserved. Caution, do not write to this register field.
                # PSU_DDR_PHY_DX7LCDLR2_RESERVED_24_16                                            0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX7LCDLR2_RESERVED_15_9                                             0x0

                # Read DQS Gating Delay
                # PSU_DDR_PHY_DX7LCDLR2_DQSGD                                                     0xa

                # DATX8 n Local Calibrated Delay Line Register 2
                #(OFFSET, MASK, VALUE)      (0XFD080E88, 0xFFFFFFFFU ,0x0000000AU)  */
    mask_write 0XFD080E88 0xFFFFFFFF 0x0000000A
                # Register : DX7GTR0 @ 0XFD080EC0</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX7GTR0_RESERVED_31_24                                              0x0

                # DQ Write Path Latency Pipeline
                # PSU_DDR_PHY_DX7GTR0_WDQSL                                                       0x0

                # Reserved. Caution, do not write to this register field.
                # PSU_DDR_PHY_DX7GTR0_RESERVED_23_20                                              0x0

                # Write Leveling System Latency
                # PSU_DDR_PHY_DX7GTR0_WLSL                                                        0x2

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX7GTR0_RESERVED_15_13                                              0x0

                # Reserved. Caution, do not write to this register field.
                # PSU_DDR_PHY_DX7GTR0_RESERVED_12_8                                               0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX7GTR0_RESERVED_7_5                                                0x0

                # DQS Gating System Latency
                # PSU_DDR_PHY_DX7GTR0_DGSL                                                        0x0

                # DATX8 n General Timing Register 0
                #(OFFSET, MASK, VALUE)      (0XFD080EC0, 0xFFFFFFFFU ,0x00020000U)  */
    mask_write 0XFD080EC0 0xFFFFFFFF 0x00020000
                # Register : DX8GCR0 @ 0XFD080F00</p>

                # Calibration Bypass
                # PSU_DDR_PHY_DX8GCR0_CALBYP                                                      0x0

                # Master Delay Line Enable
                # PSU_DDR_PHY_DX8GCR0_MDLEN                                                       0x1

                # Configurable ODT(TE) Phase Shift
                # PSU_DDR_PHY_DX8GCR0_CODTSHFT                                                    0x0

                # DQS Duty Cycle Correction
                # PSU_DDR_PHY_DX8GCR0_DQSDCC                                                      0x0

                # Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd input for the respective bypte lane of the PHY
                # PSU_DDR_PHY_DX8GCR0_RDDLY                                                       0x8

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8GCR0_RESERVED_19_14                                              0x0

                # DQSNSE Power Down Receiver
                # PSU_DDR_PHY_DX8GCR0_DQSNSEPDR                                                   0x0

                # DQSSE Power Down Receiver
                # PSU_DDR_PHY_DX8GCR0_DQSSEPDR                                                    0x0

                # RTT On Additive Latency
                # PSU_DDR_PHY_DX8GCR0_RTTOAL                                                      0x0

                # RTT Output Hold
                # PSU_DDR_PHY_DX8GCR0_RTTOH                                                       0x3

                # Configurable PDR Phase Shift
                # PSU_DDR_PHY_DX8GCR0_CPDRSHFT                                                    0x0

                # DQSR Power Down
                # PSU_DDR_PHY_DX8GCR0_DQSRPD                                                      0x0

                # DQSG Power Down Receiver
                # PSU_DDR_PHY_DX8GCR0_DQSGPDR                                                     0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8GCR0_RESERVED_4                                                  0x0

                # DQSG On-Die Termination
                # PSU_DDR_PHY_DX8GCR0_DQSGODT                                                     0x0

                # DQSG Output Enable
                # PSU_DDR_PHY_DX8GCR0_DQSGOE                                                      0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8GCR0_RESERVED_1_0                                                0x0

                # DATX8 n General Configuration Register 0
                #(OFFSET, MASK, VALUE)      (0XFD080F00, 0xFFFFFFFFU ,0x40800624U)  */
    mask_write 0XFD080F00 0xFFFFFFFF 0x40800624
                # Register : DX8GCR1 @ 0XFD080F04</p>

                # Enables the PDR mode for DQ[7:0]
                # PSU_DDR_PHY_DX8GCR1_DXPDRMODE                                                   0x0

                # Reserved. Returns zeroes on reads.
                # PSU_DDR_PHY_DX8GCR1_RESERVED_15                                                 0x0

                # Select the delayed or non-delayed read data strobe #
                # PSU_DDR_PHY_DX8GCR1_QSNSEL                                                      0x1

                # Select the delayed or non-delayed read data strobe
                # PSU_DDR_PHY_DX8GCR1_QSSEL                                                       0x1

                # Enables Read Data Strobe in a byte lane
                # PSU_DDR_PHY_DX8GCR1_OEEN                                                        0x1

                # Enables PDR in a byte lane
                # PSU_DDR_PHY_DX8GCR1_PDREN                                                       0x1

                # Enables ODT/TE in a byte lane
                # PSU_DDR_PHY_DX8GCR1_TEEN                                                        0x1

                # Enables Write Data strobe in a byte lane
                # PSU_DDR_PHY_DX8GCR1_DSEN                                                        0x1

                # Enables DM pin in a byte lane
                # PSU_DDR_PHY_DX8GCR1_DMEN                                                        0x1

                # Enables DQ corresponding to each bit in a byte
                # PSU_DDR_PHY_DX8GCR1_DQEN                                                        0x0

                # DATX8 n General Configuration Register 1
                #(OFFSET, MASK, VALUE)      (0XFD080F04, 0xFFFFFFFFU ,0x00007F00U)  */
    mask_write 0XFD080F04 0xFFFFFFFF 0x00007F00
                # Register : DX8GCR4 @ 0XFD080F10</p>

                # Byte lane VREF IOM (Used only by D4MU IOs)
                # PSU_DDR_PHY_DX8GCR4_RESERVED_31_29                                              0x0

                # Byte Lane VREF Pad Enable
                # PSU_DDR_PHY_DX8GCR4_DXREFPEN                                                    0x0

                # Byte Lane Internal VREF Enable
                # PSU_DDR_PHY_DX8GCR4_DXREFEEN                                                    0x3

                # Byte Lane Single-End VREF Enable
                # PSU_DDR_PHY_DX8GCR4_DXREFSEN                                                    0x1

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX8GCR4_RESERVED_24                                                 0x0

                # External VREF generator REFSEL range select
                # PSU_DDR_PHY_DX8GCR4_DXREFESELRANGE                                              0x0

                # Byte Lane External VREF Select
                # PSU_DDR_PHY_DX8GCR4_DXREFESEL                                                   0x0

                # Single ended VREF generator REFSEL range select
                # PSU_DDR_PHY_DX8GCR4_DXREFSSELRANGE                                              0x1

                # Byte Lane Single-End VREF Select
                # PSU_DDR_PHY_DX8GCR4_DXREFSSEL                                                   0x30

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX8GCR4_RESERVED_7_6                                                0x0

                # VREF Enable control for DQ IO (Single Ended) buffers of a byte lane.
                # PSU_DDR_PHY_DX8GCR4_DXREFIEN                                                    0xf

                # VRMON control for DQ IO (Single Ended) buffers of a byte lane.
                # PSU_DDR_PHY_DX8GCR4_DXREFIMON                                                   0x0

                # DATX8 n General Configuration Register 4
                #(OFFSET, MASK, VALUE)      (0XFD080F10, 0xFFFFFFFFU ,0x0E00B03CU)  */
    mask_write 0XFD080F10 0xFFFFFFFF 0x0E00B03C
                # Register : DX8GCR5 @ 0XFD080F14</p>

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX8GCR5_RESERVED_31                                                 0x0

                # Byte Lane internal VREF Select for Rank 3
                # PSU_DDR_PHY_DX8GCR5_DXREFISELR3                                                 0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX8GCR5_RESERVED_23                                                 0x0

                # Byte Lane internal VREF Select for Rank 2
                # PSU_DDR_PHY_DX8GCR5_DXREFISELR2                                                 0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX8GCR5_RESERVED_15                                                 0x0

                # Byte Lane internal VREF Select for Rank 1
                # PSU_DDR_PHY_DX8GCR5_DXREFISELR1                                                 0x55

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX8GCR5_RESERVED_7                                                  0x0

                # Byte Lane internal VREF Select for Rank 0
                # PSU_DDR_PHY_DX8GCR5_DXREFISELR0                                                 0x55

                # DATX8 n General Configuration Register 5
                #(OFFSET, MASK, VALUE)      (0XFD080F14, 0xFFFFFFFFU ,0x09095555U)  */
    mask_write 0XFD080F14 0xFFFFFFFF 0x09095555
                # Register : DX8GCR6 @ 0XFD080F18</p>

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX8GCR6_RESERVED_31_30                                              0x0

                # DRAM DQ VREF Select for Rank3
                # PSU_DDR_PHY_DX8GCR6_DXDQVREFR3                                                  0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX8GCR6_RESERVED_23_22                                              0x0

                # DRAM DQ VREF Select for Rank2
                # PSU_DDR_PHY_DX8GCR6_DXDQVREFR2                                                  0x9

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX8GCR6_RESERVED_15_14                                              0x0

                # DRAM DQ VREF Select for Rank1
                # PSU_DDR_PHY_DX8GCR6_DXDQVREFR1                                                  0x2b

                # Reserved. Returns zeros on reads.
                # PSU_DDR_PHY_DX8GCR6_RESERVED_7_6                                                0x0

                # DRAM DQ VREF Select for Rank0
                # PSU_DDR_PHY_DX8GCR6_DXDQVREFR0                                                  0x2b

                # DATX8 n General Configuration Register 6
                #(OFFSET, MASK, VALUE)      (0XFD080F18, 0xFFFFFFFFU ,0x09092B2BU)  */
    mask_write 0XFD080F18 0xFFFFFFFF 0x09092B2B
                # Register : DX8LCDLR2 @ 0XFD080F88</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8LCDLR2_RESERVED_31_25                                            0x0

                # Reserved. Caution, do not write to this register field.
                # PSU_DDR_PHY_DX8LCDLR2_RESERVED_24_16                                            0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8LCDLR2_RESERVED_15_9                                             0x0

                # Read DQS Gating Delay
                # PSU_DDR_PHY_DX8LCDLR2_DQSGD                                                     0x0

                # DATX8 n Local Calibrated Delay Line Register 2
                #(OFFSET, MASK, VALUE)      (0XFD080F88, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFD080F88 0xFFFFFFFF 0x00000000
                # Register : DX8GTR0 @ 0XFD080FC0</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8GTR0_RESERVED_31_24                                              0x0

                # DQ Write Path Latency Pipeline
                # PSU_DDR_PHY_DX8GTR0_WDQSL                                                       0x0

                # Reserved. Caution, do not write to this register field.
                # PSU_DDR_PHY_DX8GTR0_RESERVED_23_20                                              0x0

                # Write Leveling System Latency
                # PSU_DDR_PHY_DX8GTR0_WLSL                                                        0x2

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8GTR0_RESERVED_15_13                                              0x0

                # Reserved. Caution, do not write to this register field.
                # PSU_DDR_PHY_DX8GTR0_RESERVED_12_8                                               0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8GTR0_RESERVED_7_5                                                0x0

                # DQS Gating System Latency
                # PSU_DDR_PHY_DX8GTR0_DGSL                                                        0x0

                # DATX8 n General Timing Register 0
                #(OFFSET, MASK, VALUE)      (0XFD080FC0, 0xFFFFFFFFU ,0x00020000U)  */
    mask_write 0XFD080FC0 0xFFFFFFFF 0x00020000
                # Register : DX8SL0DQSCTL @ 0XFD08141C</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL0DQSCTL_RESERVED_31_25                                         0x0

                # Read Path Rise-to-Rise Mode
                # PSU_DDR_PHY_DX8SL0DQSCTL_RRRMODE                                                0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL0DQSCTL_RESERVED_23_22                                         0x0

                # Write Path Rise-to-Rise Mode
                # PSU_DDR_PHY_DX8SL0DQSCTL_WRRMODE                                                0x1

                # DQS Gate Extension
                # PSU_DDR_PHY_DX8SL0DQSCTL_DQSGX                                                  0x0

                # Low Power PLL Power Down
                # PSU_DDR_PHY_DX8SL0DQSCTL_LPPLLPD                                                0x1

                # Low Power I/O Power Down
                # PSU_DDR_PHY_DX8SL0DQSCTL_LPIOPD                                                 0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL0DQSCTL_RESERVED_16_15                                         0x0

                # QS Counter Enable
                # PSU_DDR_PHY_DX8SL0DQSCTL_QSCNTEN                                                0x1

                # Unused DQ I/O Mode
                # PSU_DDR_PHY_DX8SL0DQSCTL_UDQIOM                                                 0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL0DQSCTL_RESERVED_12_10                                         0x0

                # Data Slew Rate
                # PSU_DDR_PHY_DX8SL0DQSCTL_DXSR                                                   0x3

                # DQS_N Resistor
                # PSU_DDR_PHY_DX8SL0DQSCTL_DQSNRES                                                0xc

                # DQS Resistor
                # PSU_DDR_PHY_DX8SL0DQSCTL_DQSRES                                                 0x4

                # DATX8 0-1 DQS Control Register
                #(OFFSET, MASK, VALUE)      (0XFD08141C, 0xFFFFFFFFU ,0x012643C4U)  */
    mask_write 0XFD08141C 0xFFFFFFFF 0x012643C4
                # Register : DX8SL0DXCTL2 @ 0XFD08142C</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL0DXCTL2_RESERVED_31_24                                         0x0

                # Configurable Read Data Enable
                # PSU_DDR_PHY_DX8SL0DXCTL2_CRDEN                                                  0x0

                # OX Extension during Post-amble
                # PSU_DDR_PHY_DX8SL0DXCTL2_POSOEX                                                 0x0

                # OE Extension during Pre-amble
                # PSU_DDR_PHY_DX8SL0DXCTL2_PREOEX                                                 0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL0DXCTL2_RESERVED_17                                            0x0

                # I/O Assisted Gate Select
                # PSU_DDR_PHY_DX8SL0DXCTL2_IOAG                                                   0x0

                # I/O Loopback Select
                # PSU_DDR_PHY_DX8SL0DXCTL2_IOLB                                                   0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL0DXCTL2_RESERVED_14_13                                         0x0

                # Low Power Wakeup Threshold
                # PSU_DDR_PHY_DX8SL0DXCTL2_LPWAKEUP_THRSH                                         0xc

                # Read Data Bus Inversion Enable
                # PSU_DDR_PHY_DX8SL0DXCTL2_RDBI                                                   0x0

                # Write Data Bus Inversion Enable
                # PSU_DDR_PHY_DX8SL0DXCTL2_WDBI                                                   0x0

                # PUB Read FIFO Bypass
                # PSU_DDR_PHY_DX8SL0DXCTL2_PRFBYP                                                 0x0

                # DATX8 Receive FIFO Read Mode
                # PSU_DDR_PHY_DX8SL0DXCTL2_RDMODE                                                 0x0

                # Disables the Read FIFO Reset
                # PSU_DDR_PHY_DX8SL0DXCTL2_DISRST                                                 0x0

                # Read DQS Gate I/O Loopback
                # PSU_DDR_PHY_DX8SL0DXCTL2_DQSGLB                                                 0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL0DXCTL2_RESERVED_0                                             0x0

                # DATX8 0-1 DX Control Register 2
                #(OFFSET, MASK, VALUE)      (0XFD08142C, 0xFFFFFFFFU ,0x00001800U)  */
    mask_write 0XFD08142C 0xFFFFFFFF 0x00001800
                # Register : DX8SL0IOCR @ 0XFD081430</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL0IOCR_RESERVED_31                                              0x0

                # PVREF_DAC REFSEL range select
                # PSU_DDR_PHY_DX8SL0IOCR_DXDACRANGE                                               0x7

                # IOM bits for PVREF, PVREF_DAC and PVREFE cells in DX IO ring
                # PSU_DDR_PHY_DX8SL0IOCR_DXVREFIOM                                                0x0

                # DX IO Mode
                # PSU_DDR_PHY_DX8SL0IOCR_DXIOM                                                    0x2

                # DX IO Transmitter Mode
                # PSU_DDR_PHY_DX8SL0IOCR_DXTXM                                                    0x0

                # DX IO Receiver Mode
                # PSU_DDR_PHY_DX8SL0IOCR_DXRXM                                                    0x0

                # DATX8 0-1 I/O Configuration Register
                #(OFFSET, MASK, VALUE)      (0XFD081430, 0xFFFFFFFFU ,0x70800000U)  */
    mask_write 0XFD081430 0xFFFFFFFF 0x70800000
                # Register : DX8SL1DQSCTL @ 0XFD08145C</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL1DQSCTL_RESERVED_31_25                                         0x0

                # Read Path Rise-to-Rise Mode
                # PSU_DDR_PHY_DX8SL1DQSCTL_RRRMODE                                                0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL1DQSCTL_RESERVED_23_22                                         0x0

                # Write Path Rise-to-Rise Mode
                # PSU_DDR_PHY_DX8SL1DQSCTL_WRRMODE                                                0x1

                # DQS Gate Extension
                # PSU_DDR_PHY_DX8SL1DQSCTL_DQSGX                                                  0x0

                # Low Power PLL Power Down
                # PSU_DDR_PHY_DX8SL1DQSCTL_LPPLLPD                                                0x1

                # Low Power I/O Power Down
                # PSU_DDR_PHY_DX8SL1DQSCTL_LPIOPD                                                 0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL1DQSCTL_RESERVED_16_15                                         0x0

                # QS Counter Enable
                # PSU_DDR_PHY_DX8SL1DQSCTL_QSCNTEN                                                0x1

                # Unused DQ I/O Mode
                # PSU_DDR_PHY_DX8SL1DQSCTL_UDQIOM                                                 0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL1DQSCTL_RESERVED_12_10                                         0x0

                # Data Slew Rate
                # PSU_DDR_PHY_DX8SL1DQSCTL_DXSR                                                   0x3

                # DQS_N Resistor
                # PSU_DDR_PHY_DX8SL1DQSCTL_DQSNRES                                                0xc

                # DQS Resistor
                # PSU_DDR_PHY_DX8SL1DQSCTL_DQSRES                                                 0x4

                # DATX8 0-1 DQS Control Register
                #(OFFSET, MASK, VALUE)      (0XFD08145C, 0xFFFFFFFFU ,0x012643C4U)  */
    mask_write 0XFD08145C 0xFFFFFFFF 0x012643C4
                # Register : DX8SL1DXCTL2 @ 0XFD08146C</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL1DXCTL2_RESERVED_31_24                                         0x0

                # Configurable Read Data Enable
                # PSU_DDR_PHY_DX8SL1DXCTL2_CRDEN                                                  0x0

                # OX Extension during Post-amble
                # PSU_DDR_PHY_DX8SL1DXCTL2_POSOEX                                                 0x0

                # OE Extension during Pre-amble
                # PSU_DDR_PHY_DX8SL1DXCTL2_PREOEX                                                 0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL1DXCTL2_RESERVED_17                                            0x0

                # I/O Assisted Gate Select
                # PSU_DDR_PHY_DX8SL1DXCTL2_IOAG                                                   0x0

                # I/O Loopback Select
                # PSU_DDR_PHY_DX8SL1DXCTL2_IOLB                                                   0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL1DXCTL2_RESERVED_14_13                                         0x0

                # Low Power Wakeup Threshold
                # PSU_DDR_PHY_DX8SL1DXCTL2_LPWAKEUP_THRSH                                         0xc

                # Read Data Bus Inversion Enable
                # PSU_DDR_PHY_DX8SL1DXCTL2_RDBI                                                   0x0

                # Write Data Bus Inversion Enable
                # PSU_DDR_PHY_DX8SL1DXCTL2_WDBI                                                   0x0

                # PUB Read FIFO Bypass
                # PSU_DDR_PHY_DX8SL1DXCTL2_PRFBYP                                                 0x0

                # DATX8 Receive FIFO Read Mode
                # PSU_DDR_PHY_DX8SL1DXCTL2_RDMODE                                                 0x0

                # Disables the Read FIFO Reset
                # PSU_DDR_PHY_DX8SL1DXCTL2_DISRST                                                 0x0

                # Read DQS Gate I/O Loopback
                # PSU_DDR_PHY_DX8SL1DXCTL2_DQSGLB                                                 0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL1DXCTL2_RESERVED_0                                             0x0

                # DATX8 0-1 DX Control Register 2
                #(OFFSET, MASK, VALUE)      (0XFD08146C, 0xFFFFFFFFU ,0x00001800U)  */
    mask_write 0XFD08146C 0xFFFFFFFF 0x00001800
                # Register : DX8SL1IOCR @ 0XFD081470</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL1IOCR_RESERVED_31                                              0x0

                # PVREF_DAC REFSEL range select
                # PSU_DDR_PHY_DX8SL1IOCR_DXDACRANGE                                               0x7

                # IOM bits for PVREF, PVREF_DAC and PVREFE cells in DX IO ring
                # PSU_DDR_PHY_DX8SL1IOCR_DXVREFIOM                                                0x0

                # DX IO Mode
                # PSU_DDR_PHY_DX8SL1IOCR_DXIOM                                                    0x2

                # DX IO Transmitter Mode
                # PSU_DDR_PHY_DX8SL1IOCR_DXTXM                                                    0x0

                # DX IO Receiver Mode
                # PSU_DDR_PHY_DX8SL1IOCR_DXRXM                                                    0x0

                # DATX8 0-1 I/O Configuration Register
                #(OFFSET, MASK, VALUE)      (0XFD081470, 0xFFFFFFFFU ,0x70800000U)  */
    mask_write 0XFD081470 0xFFFFFFFF 0x70800000
                # Register : DX8SL2DQSCTL @ 0XFD08149C</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL2DQSCTL_RESERVED_31_25                                         0x0

                # Read Path Rise-to-Rise Mode
                # PSU_DDR_PHY_DX8SL2DQSCTL_RRRMODE                                                0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL2DQSCTL_RESERVED_23_22                                         0x0

                # Write Path Rise-to-Rise Mode
                # PSU_DDR_PHY_DX8SL2DQSCTL_WRRMODE                                                0x1

                # DQS Gate Extension
                # PSU_DDR_PHY_DX8SL2DQSCTL_DQSGX                                                  0x0

                # Low Power PLL Power Down
                # PSU_DDR_PHY_DX8SL2DQSCTL_LPPLLPD                                                0x1

                # Low Power I/O Power Down
                # PSU_DDR_PHY_DX8SL2DQSCTL_LPIOPD                                                 0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL2DQSCTL_RESERVED_16_15                                         0x0

                # QS Counter Enable
                # PSU_DDR_PHY_DX8SL2DQSCTL_QSCNTEN                                                0x1

                # Unused DQ I/O Mode
                # PSU_DDR_PHY_DX8SL2DQSCTL_UDQIOM                                                 0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL2DQSCTL_RESERVED_12_10                                         0x0

                # Data Slew Rate
                # PSU_DDR_PHY_DX8SL2DQSCTL_DXSR                                                   0x3

                # DQS_N Resistor
                # PSU_DDR_PHY_DX8SL2DQSCTL_DQSNRES                                                0xc

                # DQS Resistor
                # PSU_DDR_PHY_DX8SL2DQSCTL_DQSRES                                                 0x4

                # DATX8 0-1 DQS Control Register
                #(OFFSET, MASK, VALUE)      (0XFD08149C, 0xFFFFFFFFU ,0x012643C4U)  */
    mask_write 0XFD08149C 0xFFFFFFFF 0x012643C4
                # Register : DX8SL2DXCTL2 @ 0XFD0814AC</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL2DXCTL2_RESERVED_31_24                                         0x0

                # Configurable Read Data Enable
                # PSU_DDR_PHY_DX8SL2DXCTL2_CRDEN                                                  0x0

                # OX Extension during Post-amble
                # PSU_DDR_PHY_DX8SL2DXCTL2_POSOEX                                                 0x0

                # OE Extension during Pre-amble
                # PSU_DDR_PHY_DX8SL2DXCTL2_PREOEX                                                 0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL2DXCTL2_RESERVED_17                                            0x0

                # I/O Assisted Gate Select
                # PSU_DDR_PHY_DX8SL2DXCTL2_IOAG                                                   0x0

                # I/O Loopback Select
                # PSU_DDR_PHY_DX8SL2DXCTL2_IOLB                                                   0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL2DXCTL2_RESERVED_14_13                                         0x0

                # Low Power Wakeup Threshold
                # PSU_DDR_PHY_DX8SL2DXCTL2_LPWAKEUP_THRSH                                         0xc

                # Read Data Bus Inversion Enable
                # PSU_DDR_PHY_DX8SL2DXCTL2_RDBI                                                   0x0

                # Write Data Bus Inversion Enable
                # PSU_DDR_PHY_DX8SL2DXCTL2_WDBI                                                   0x0

                # PUB Read FIFO Bypass
                # PSU_DDR_PHY_DX8SL2DXCTL2_PRFBYP                                                 0x0

                # DATX8 Receive FIFO Read Mode
                # PSU_DDR_PHY_DX8SL2DXCTL2_RDMODE                                                 0x0

                # Disables the Read FIFO Reset
                # PSU_DDR_PHY_DX8SL2DXCTL2_DISRST                                                 0x0

                # Read DQS Gate I/O Loopback
                # PSU_DDR_PHY_DX8SL2DXCTL2_DQSGLB                                                 0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL2DXCTL2_RESERVED_0                                             0x0

                # DATX8 0-1 DX Control Register 2
                #(OFFSET, MASK, VALUE)      (0XFD0814AC, 0xFFFFFFFFU ,0x00001800U)  */
    mask_write 0XFD0814AC 0xFFFFFFFF 0x00001800
                # Register : DX8SL2IOCR @ 0XFD0814B0</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL2IOCR_RESERVED_31                                              0x0

                # PVREF_DAC REFSEL range select
                # PSU_DDR_PHY_DX8SL2IOCR_DXDACRANGE                                               0x7

                # IOM bits for PVREF, PVREF_DAC and PVREFE cells in DX IO ring
                # PSU_DDR_PHY_DX8SL2IOCR_DXVREFIOM                                                0x0

                # DX IO Mode
                # PSU_DDR_PHY_DX8SL2IOCR_DXIOM                                                    0x2

                # DX IO Transmitter Mode
                # PSU_DDR_PHY_DX8SL2IOCR_DXTXM                                                    0x0

                # DX IO Receiver Mode
                # PSU_DDR_PHY_DX8SL2IOCR_DXRXM                                                    0x0

                # DATX8 0-1 I/O Configuration Register
                #(OFFSET, MASK, VALUE)      (0XFD0814B0, 0xFFFFFFFFU ,0x70800000U)  */
    mask_write 0XFD0814B0 0xFFFFFFFF 0x70800000
                # Register : DX8SL3DQSCTL @ 0XFD0814DC</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL3DQSCTL_RESERVED_31_25                                         0x0

                # Read Path Rise-to-Rise Mode
                # PSU_DDR_PHY_DX8SL3DQSCTL_RRRMODE                                                0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL3DQSCTL_RESERVED_23_22                                         0x0

                # Write Path Rise-to-Rise Mode
                # PSU_DDR_PHY_DX8SL3DQSCTL_WRRMODE                                                0x1

                # DQS Gate Extension
                # PSU_DDR_PHY_DX8SL3DQSCTL_DQSGX                                                  0x0

                # Low Power PLL Power Down
                # PSU_DDR_PHY_DX8SL3DQSCTL_LPPLLPD                                                0x1

                # Low Power I/O Power Down
                # PSU_DDR_PHY_DX8SL3DQSCTL_LPIOPD                                                 0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL3DQSCTL_RESERVED_16_15                                         0x0

                # QS Counter Enable
                # PSU_DDR_PHY_DX8SL3DQSCTL_QSCNTEN                                                0x1

                # Unused DQ I/O Mode
                # PSU_DDR_PHY_DX8SL3DQSCTL_UDQIOM                                                 0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL3DQSCTL_RESERVED_12_10                                         0x0

                # Data Slew Rate
                # PSU_DDR_PHY_DX8SL3DQSCTL_DXSR                                                   0x3

                # DQS_N Resistor
                # PSU_DDR_PHY_DX8SL3DQSCTL_DQSNRES                                                0xc

                # DQS Resistor
                # PSU_DDR_PHY_DX8SL3DQSCTL_DQSRES                                                 0x4

                # DATX8 0-1 DQS Control Register
                #(OFFSET, MASK, VALUE)      (0XFD0814DC, 0xFFFFFFFFU ,0x012643C4U)  */
    mask_write 0XFD0814DC 0xFFFFFFFF 0x012643C4
                # Register : DX8SL3DXCTL2 @ 0XFD0814EC</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL3DXCTL2_RESERVED_31_24                                         0x0

                # Configurable Read Data Enable
                # PSU_DDR_PHY_DX8SL3DXCTL2_CRDEN                                                  0x0

                # OX Extension during Post-amble
                # PSU_DDR_PHY_DX8SL3DXCTL2_POSOEX                                                 0x0

                # OE Extension during Pre-amble
                # PSU_DDR_PHY_DX8SL3DXCTL2_PREOEX                                                 0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL3DXCTL2_RESERVED_17                                            0x0

                # I/O Assisted Gate Select
                # PSU_DDR_PHY_DX8SL3DXCTL2_IOAG                                                   0x0

                # I/O Loopback Select
                # PSU_DDR_PHY_DX8SL3DXCTL2_IOLB                                                   0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL3DXCTL2_RESERVED_14_13                                         0x0

                # Low Power Wakeup Threshold
                # PSU_DDR_PHY_DX8SL3DXCTL2_LPWAKEUP_THRSH                                         0xc

                # Read Data Bus Inversion Enable
                # PSU_DDR_PHY_DX8SL3DXCTL2_RDBI                                                   0x0

                # Write Data Bus Inversion Enable
                # PSU_DDR_PHY_DX8SL3DXCTL2_WDBI                                                   0x0

                # PUB Read FIFO Bypass
                # PSU_DDR_PHY_DX8SL3DXCTL2_PRFBYP                                                 0x0

                # DATX8 Receive FIFO Read Mode
                # PSU_DDR_PHY_DX8SL3DXCTL2_RDMODE                                                 0x0

                # Disables the Read FIFO Reset
                # PSU_DDR_PHY_DX8SL3DXCTL2_DISRST                                                 0x0

                # Read DQS Gate I/O Loopback
                # PSU_DDR_PHY_DX8SL3DXCTL2_DQSGLB                                                 0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL3DXCTL2_RESERVED_0                                             0x0

                # DATX8 0-1 DX Control Register 2
                #(OFFSET, MASK, VALUE)      (0XFD0814EC, 0xFFFFFFFFU ,0x00001800U)  */
    mask_write 0XFD0814EC 0xFFFFFFFF 0x00001800
                # Register : DX8SL3IOCR @ 0XFD0814F0</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL3IOCR_RESERVED_31                                              0x0

                # PVREF_DAC REFSEL range select
                # PSU_DDR_PHY_DX8SL3IOCR_DXDACRANGE                                               0x7

                # IOM bits for PVREF, PVREF_DAC and PVREFE cells in DX IO ring
                # PSU_DDR_PHY_DX8SL3IOCR_DXVREFIOM                                                0x0

                # DX IO Mode
                # PSU_DDR_PHY_DX8SL3IOCR_DXIOM                                                    0x2

                # DX IO Transmitter Mode
                # PSU_DDR_PHY_DX8SL3IOCR_DXTXM                                                    0x0

                # DX IO Receiver Mode
                # PSU_DDR_PHY_DX8SL3IOCR_DXRXM                                                    0x0

                # DATX8 0-1 I/O Configuration Register
                #(OFFSET, MASK, VALUE)      (0XFD0814F0, 0xFFFFFFFFU ,0x70800000U)  */
    mask_write 0XFD0814F0 0xFFFFFFFF 0x70800000
                # Register : DX8SL4DQSCTL @ 0XFD08151C</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL4DQSCTL_RESERVED_31_25                                         0x0

                # Read Path Rise-to-Rise Mode
                # PSU_DDR_PHY_DX8SL4DQSCTL_RRRMODE                                                0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL4DQSCTL_RESERVED_23_22                                         0x0

                # Write Path Rise-to-Rise Mode
                # PSU_DDR_PHY_DX8SL4DQSCTL_WRRMODE                                                0x1

                # DQS Gate Extension
                # PSU_DDR_PHY_DX8SL4DQSCTL_DQSGX                                                  0x0

                # Low Power PLL Power Down
                # PSU_DDR_PHY_DX8SL4DQSCTL_LPPLLPD                                                0x1

                # Low Power I/O Power Down
                # PSU_DDR_PHY_DX8SL4DQSCTL_LPIOPD                                                 0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL4DQSCTL_RESERVED_16_15                                         0x0

                # QS Counter Enable
                # PSU_DDR_PHY_DX8SL4DQSCTL_QSCNTEN                                                0x1

                # Unused DQ I/O Mode
                # PSU_DDR_PHY_DX8SL4DQSCTL_UDQIOM                                                 0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL4DQSCTL_RESERVED_12_10                                         0x0

                # Data Slew Rate
                # PSU_DDR_PHY_DX8SL4DQSCTL_DXSR                                                   0x3

                # DQS_N Resistor
                # PSU_DDR_PHY_DX8SL4DQSCTL_DQSNRES                                                0xc

                # DQS Resistor
                # PSU_DDR_PHY_DX8SL4DQSCTL_DQSRES                                                 0x4

                # DATX8 0-1 DQS Control Register
                #(OFFSET, MASK, VALUE)      (0XFD08151C, 0xFFFFFFFFU ,0x012643C4U)  */
    mask_write 0XFD08151C 0xFFFFFFFF 0x012643C4
                # Register : DX8SL4DXCTL2 @ 0XFD08152C</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL4DXCTL2_RESERVED_31_24                                         0x0

                # Configurable Read Data Enable
                # PSU_DDR_PHY_DX8SL4DXCTL2_CRDEN                                                  0x0

                # OX Extension during Post-amble
                # PSU_DDR_PHY_DX8SL4DXCTL2_POSOEX                                                 0x0

                # OE Extension during Pre-amble
                # PSU_DDR_PHY_DX8SL4DXCTL2_PREOEX                                                 0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL4DXCTL2_RESERVED_17                                            0x0

                # I/O Assisted Gate Select
                # PSU_DDR_PHY_DX8SL4DXCTL2_IOAG                                                   0x0

                # I/O Loopback Select
                # PSU_DDR_PHY_DX8SL4DXCTL2_IOLB                                                   0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL4DXCTL2_RESERVED_14_13                                         0x0

                # Low Power Wakeup Threshold
                # PSU_DDR_PHY_DX8SL4DXCTL2_LPWAKEUP_THRSH                                         0xc

                # Read Data Bus Inversion Enable
                # PSU_DDR_PHY_DX8SL4DXCTL2_RDBI                                                   0x0

                # Write Data Bus Inversion Enable
                # PSU_DDR_PHY_DX8SL4DXCTL2_WDBI                                                   0x0

                # PUB Read FIFO Bypass
                # PSU_DDR_PHY_DX8SL4DXCTL2_PRFBYP                                                 0x0

                # DATX8 Receive FIFO Read Mode
                # PSU_DDR_PHY_DX8SL4DXCTL2_RDMODE                                                 0x0

                # Disables the Read FIFO Reset
                # PSU_DDR_PHY_DX8SL4DXCTL2_DISRST                                                 0x0

                # Read DQS Gate I/O Loopback
                # PSU_DDR_PHY_DX8SL4DXCTL2_DQSGLB                                                 0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL4DXCTL2_RESERVED_0                                             0x0

                # DATX8 0-1 DX Control Register 2
                #(OFFSET, MASK, VALUE)      (0XFD08152C, 0xFFFFFFFFU ,0x00001800U)  */
    mask_write 0XFD08152C 0xFFFFFFFF 0x00001800
                # Register : DX8SL4IOCR @ 0XFD081530</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SL4IOCR_RESERVED_31                                              0x0

                # PVREF_DAC REFSEL range select
                # PSU_DDR_PHY_DX8SL4IOCR_DXDACRANGE                                               0x7

                # IOM bits for PVREF, PVREF_DAC and PVREFE cells in DX IO ring
                # PSU_DDR_PHY_DX8SL4IOCR_DXVREFIOM                                                0x0

                # DX IO Mode
                # PSU_DDR_PHY_DX8SL4IOCR_DXIOM                                                    0x2

                # DX IO Transmitter Mode
                # PSU_DDR_PHY_DX8SL4IOCR_DXTXM                                                    0x0

                # DX IO Receiver Mode
                # PSU_DDR_PHY_DX8SL4IOCR_DXRXM                                                    0x0

                # DATX8 0-1 I/O Configuration Register
                #(OFFSET, MASK, VALUE)      (0XFD081530, 0xFFFFFFFFU ,0x70800000U)  */
    mask_write 0XFD081530 0xFFFFFFFF 0x70800000
                # Register : DX8SLbDQSCTL @ 0XFD0817DC</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SLBDQSCTL_RESERVED_31_25                                         0x0

                # Read Path Rise-to-Rise Mode
                # PSU_DDR_PHY_DX8SLBDQSCTL_RRRMODE                                                0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SLBDQSCTL_RESERVED_23_22                                         0x0

                # Write Path Rise-to-Rise Mode
                # PSU_DDR_PHY_DX8SLBDQSCTL_WRRMODE                                                0x1

                # DQS Gate Extension
                # PSU_DDR_PHY_DX8SLBDQSCTL_DQSGX                                                  0x0

                # Low Power PLL Power Down
                # PSU_DDR_PHY_DX8SLBDQSCTL_LPPLLPD                                                0x1

                # Low Power I/O Power Down
                # PSU_DDR_PHY_DX8SLBDQSCTL_LPIOPD                                                 0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SLBDQSCTL_RESERVED_16_15                                         0x0

                # QS Counter Enable
                # PSU_DDR_PHY_DX8SLBDQSCTL_QSCNTEN                                                0x1

                # Unused DQ I/O Mode
                # PSU_DDR_PHY_DX8SLBDQSCTL_UDQIOM                                                 0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_DX8SLBDQSCTL_RESERVED_12_10                                         0x0

                # Data Slew Rate
                # PSU_DDR_PHY_DX8SLBDQSCTL_DXSR                                                   0x3

                # DQS# Resistor
                # PSU_DDR_PHY_DX8SLBDQSCTL_DQSNRES                                                0xc

                # DQS Resistor
                # PSU_DDR_PHY_DX8SLBDQSCTL_DQSRES                                                 0x4

                # DATX8 0-8 DQS Control Register
                #(OFFSET, MASK, VALUE)      (0XFD0817DC, 0xFFFFFFFFU ,0x012643C4U)  */
    mask_write 0XFD0817DC 0xFFFFFFFF 0x012643C4
                # Register : PIR @ 0XFD080004</p>

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_PIR_RESERVED_31                                                     0x0

                # Impedance Calibration Bypass
                # PSU_DDR_PHY_PIR_ZCALBYP                                                         0x0

                # Digital Delay Line (DDL) Calibration Pause
                # PSU_DDR_PHY_PIR_DCALPSE                                                         0x0

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_PIR_RESERVED_28_21                                                  0x0

                # Write DQS2DQ Training
                # PSU_DDR_PHY_PIR_DQS2DQ                                                          0x0

                # RDIMM Initialization
                # PSU_DDR_PHY_PIR_RDIMMINIT                                                       0x0

                # Controller DRAM Initialization
                # PSU_DDR_PHY_PIR_CTLDINIT                                                        0x1

                # VREF Training
                # PSU_DDR_PHY_PIR_VREF                                                            0x0

                # Static Read Training
                # PSU_DDR_PHY_PIR_SRD                                                             0x0

                # Write Data Eye Training
                # PSU_DDR_PHY_PIR_WREYE                                                           0x0

                # Read Data Eye Training
                # PSU_DDR_PHY_PIR_RDEYE                                                           0x0

                # Write Data Bit Deskew
                # PSU_DDR_PHY_PIR_WRDSKW                                                          0x0

                # Read Data Bit Deskew
                # PSU_DDR_PHY_PIR_RDDSKW                                                          0x0

                # Write Leveling Adjust
                # PSU_DDR_PHY_PIR_WLADJ                                                           0x0

                # Read DQS Gate Training
                # PSU_DDR_PHY_PIR_QSGATE                                                          0x0

                # Write Leveling
                # PSU_DDR_PHY_PIR_WL                                                              0x0

                # DRAM Initialization
                # PSU_DDR_PHY_PIR_DRAMINIT                                                        0x0

                # DRAM Reset (DDR3/DDR4/LPDDR4 Only)
                # PSU_DDR_PHY_PIR_DRAMRST                                                         0x0

                # PHY Reset
                # PSU_DDR_PHY_PIR_PHYRST                                                          0x1

                # Digital Delay Line (DDL) Calibration
                # PSU_DDR_PHY_PIR_DCAL                                                            0x1

                # PLL Initialiazation
                # PSU_DDR_PHY_PIR_PLLINIT                                                         0x1

                # Reserved. Return zeroes on reads.
                # PSU_DDR_PHY_PIR_RESERVED_3                                                      0x0

                # CA Training
                # PSU_DDR_PHY_PIR_CA                                                              0x0

                # Impedance Calibration
                # PSU_DDR_PHY_PIR_ZCAL                                                            0x1

                # Initialization Trigger
                # PSU_DDR_PHY_PIR_INIT                                                            0x1

                # PHY Initialization Register
                #(OFFSET, MASK, VALUE)      (0XFD080004, 0xFFFFFFFFU ,0x00040073U)  */
    mask_write 0XFD080004 0xFFFFFFFF 0x00040073
}

set psu_mio_init_data {
                # : MIO PROGRAMMING
                # Register : MIO_PIN_0 @ 0XFF180000</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Output, qspi_sclk_out- (QSPI Clock)
                # PSU_IOU_SLCR_MIO_PIN_0_L0_SEL                                                   1

                # Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_0_L1_SEL                                                   0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[0]- (Test Scan Port) = test_scan, Outp
                # t, test_scan_out[0]- (Test Scan Port) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_0_L2_SEL                                                   0

                # Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[0]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[0]- (GPIO bank 0) 1= can
                # , Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL signa
                # ) 3= pjtag, Input, pjtag_tck- (PJTAG TCK) 4= spi0, Input, spi0_sclk_in- (SPI Clock) 4= spi0, Output, spi0_sclk_out- (SPI Cloc
                # ) 5= ttc3, Input, ttc3_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, Output, trace_
                # lk- (Trace Port Clock)
                # PSU_IOU_SLCR_MIO_PIN_0_L3_SEL                                                   0

                # Configures MIO Pin 0 peripheral interface mapping. S
                #(OFFSET, MASK, VALUE)      (0XFF180000, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180000 0x000000FE 0x00000002
                # Register : MIO_PIN_1 @ 0XFF180004</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi_mi1- (QSPI Databus) 1= qspi, Output, qspi_so_mo1- (QSPI Data
                # us)
                # PSU_IOU_SLCR_MIO_PIN_1_L0_SEL                                                   1

                # Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_1_L1_SEL                                                   0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[1]- (Test Scan Port) = test_scan, Outp
                # t, test_scan_out[1]- (Test Scan Port) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_1_L2_SEL                                                   0

                # Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[1]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[1]- (GPIO bank 0) 1= can
                # , Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA signal
                #  3= pjtag, Input, pjtag_tdi- (PJTAG TDI) 4= spi0, Output, spi0_n_ss_out[2]- (SPI Master Selects) 5= ttc3, Output, ttc3_wave_o
                # t- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7= trace, Output, trace_ctl- (Trace Port Control
                # Signal)
                # PSU_IOU_SLCR_MIO_PIN_1_L3_SEL                                                   0

                # Configures MIO Pin 1 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180004, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180004 0x000000FE 0x00000002
                # Register : MIO_PIN_2 @ 0XFF180008</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi2- (QSPI Databus) 1= qspi, Output, qspi_mo2- (QSPI Databus)
                # PSU_IOU_SLCR_MIO_PIN_2_L0_SEL                                                   1

                # Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_2_L1_SEL                                                   0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[2]- (Test Scan Port) = test_scan, Outp
                # t, test_scan_out[2]- (Test Scan Port) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_2_L2_SEL                                                   0

                # Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[2]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[2]- (GPIO bank 0) 1= can
                # , Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL signal
                #  3= pjtag, Output, pjtag_tdo- (PJTAG TDO) 4= spi0, Output, spi0_n_ss_out[1]- (SPI Master Selects) 5= ttc2, Input, ttc2_clk_in
                #  (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output, tracedq[0]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_2_L3_SEL                                                   0

                # Configures MIO Pin 2 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180008, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180008 0x000000FE 0x00000002
                # Register : MIO_PIN_3 @ 0XFF18000C</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi3- (QSPI Databus) 1= qspi, Output, qspi_mo3- (QSPI Databus)
                # PSU_IOU_SLCR_MIO_PIN_3_L0_SEL                                                   1

                # Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_3_L1_SEL                                                   0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[3]- (Test Scan Port) = test_scan, Outp
                # t, test_scan_out[3]- (Test Scan Port) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_3_L2_SEL                                                   0

                # Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[3]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[3]- (GPIO bank 0) 1= can
                # , Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA signa
                # ) 3= pjtag, Input, pjtag_tms- (PJTAG TMS) 4= spi0, Input, spi0_n_ss_in- (SPI Master Selects) 4= spi0, Output, spi0_n_ss_out[0
                # - (SPI Master Selects) 5= ttc2, Output, ttc2_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial
                # output) 7= trace, Output, tracedq[1]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_3_L3_SEL                                                   0

                # Configures MIO Pin 3 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF18000C, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF18000C 0x000000FE 0x00000002
                # Register : MIO_PIN_4 @ 0XFF180010</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Output, qspi_mo_mo0- (QSPI Databus) 1= qspi, Input, qspi_si_mi0- (QSPI Data
                # us)
                # PSU_IOU_SLCR_MIO_PIN_4_L0_SEL                                                   1

                # Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_4_L1_SEL                                                   0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[4]- (Test Scan Port) = test_scan, Outp
                # t, test_scan_out[4]- (Test Scan Port) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_4_L2_SEL                                                   0

                # Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[4]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[4]- (GPIO bank 0) 1= can
                # , Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL signa
                # ) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi0, Input, spi0_mi- (MISO signal) 4= spi0, Output, spi0_s
                # - (MISO signal) 5= ttc1, Input, ttc1_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, 
                # utput, tracedq[2]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_4_L3_SEL                                                   0

                # Configures MIO Pin 4 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180010, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180010 0x000000FE 0x00000002
                # Register : MIO_PIN_5 @ 0XFF180014</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Output, qspi_n_ss_out- (QSPI Slave Select)
                # PSU_IOU_SLCR_MIO_PIN_5_L0_SEL                                                   1

                # Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_5_L1_SEL                                                   0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[5]- (Test Scan Port) = test_scan, Outp
                # t, test_scan_out[5]- (Test Scan Port) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_5_L2_SEL                                                   0

                # Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[5]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[5]- (GPIO bank 0) 1= can
                # , Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA signal
                #  3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi0, Output, spi0_mo- (MOSI signal) 4= spi0, Input, spi0
                # si- (MOSI signal) 5= ttc1, Output, ttc1_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7
                #  trace, Output, tracedq[3]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_5_L3_SEL                                                   0

                # Configures MIO Pin 5 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180014, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180014 0x000000FE 0x00000002
                # Register : MIO_PIN_6 @ 0XFF180018</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Output, qspi_clk_for_lpbk- (QSPI Clock to be fed-back)
                # PSU_IOU_SLCR_MIO_PIN_6_L0_SEL                                                   1

                # Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_6_L1_SEL                                                   0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[6]- (Test Scan Port) = test_scan, Outp
                # t, test_scan_out[6]- (Test Scan Port) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_6_L2_SEL                                                   0

                # Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[6]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[6]- (GPIO bank 0) 1= can
                # , Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL signal
                #  3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_sclk_in- (SPI Clock) 4= spi1, Output, spi1
                # sclk_out- (SPI Clock) 5= ttc0, Input, ttc0_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace,
                # Output, tracedq[4]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_6_L3_SEL                                                   0

                # Configures MIO Pin 6 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180018, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180018 0x000000FE 0x00000002
                # Register : MIO_PIN_7 @ 0XFF18001C</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Output, qspi_n_ss_out_upper- (QSPI Slave Select upper)
                # PSU_IOU_SLCR_MIO_PIN_7_L0_SEL                                                   1

                # Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_7_L1_SEL                                                   0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[7]- (Test Scan Port) = test_scan, Outp
                # t, test_scan_out[7]- (Test Scan Port) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_7_L2_SEL                                                   0

                # Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[7]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[7]- (GPIO bank 0) 1= can
                # , Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA signa
                # ) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_n_ss_out[2]- (SPI Master Selects) 5= 
                # tc0, Output, ttc0_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial output) 7= trace, Output, 
                # racedq[5]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_7_L3_SEL                                                   0

                # Configures MIO Pin 7 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF18001C, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF18001C 0x000000FE 0x00000002
                # Register : MIO_PIN_8 @ 0XFF180020</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi_upper[0]- (QSPI Upper Databus) 1= qspi, Output, qspi_mo_uppe
                # [0]- (QSPI Upper Databus)
                # PSU_IOU_SLCR_MIO_PIN_8_L0_SEL                                                   1

                # Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_8_L1_SEL                                                   0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[8]- (Test Scan Port) = test_scan, Outp
                # t, test_scan_out[8]- (Test Scan Port) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_8_L2_SEL                                                   0

                # Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[8]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[8]- (GPIO bank 0) 1= can
                # , Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL signa
                # ) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi1, Output, spi1_n_ss_out[1]- (SPI Master Selects) 5= ttc
                # , Input, ttc3_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, Output, tracedq[6]- (Tr
                # ce Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_8_L3_SEL                                                   0

                # Configures MIO Pin 8 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180020, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180020 0x000000FE 0x00000002
                # Register : MIO_PIN_9 @ 0XFF180024</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi_upper[1]- (QSPI Upper Databus) 1= qspi, Output, qspi_mo_uppe
                # [1]- (QSPI Upper Databus)
                # PSU_IOU_SLCR_MIO_PIN_9_L0_SEL                                                   1

                # Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_ce[1]- (NAND chip enable)
                # PSU_IOU_SLCR_MIO_PIN_9_L1_SEL                                                   0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[9]- (Test Scan Port) = test_scan, Outp
                # t, test_scan_out[9]- (Test Scan Port) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_9_L2_SEL                                                   0

                # Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[9]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[9]- (GPIO bank 0) 1= can
                # , Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA signal
                #  3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi1, Input, spi1_n_ss_in- (SPI Master Selects) 4= spi1, 
                # utput, spi1_n_ss_out[0]- (SPI Master Selects) 5= ttc3, Output, ttc3_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (U
                # RT receiver serial input) 7= trace, Output, tracedq[7]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_9_L3_SEL                                                   0

                # Configures MIO Pin 9 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180024, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180024 0x000000FE 0x00000002
                # Register : MIO_PIN_10 @ 0XFF180028</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi_upper[2]- (QSPI Upper Databus) 1= qspi, Output, qspi_mo_uppe
                # [2]- (QSPI Upper Databus)
                # PSU_IOU_SLCR_MIO_PIN_10_L0_SEL                                                  1

                # Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_rb_n[0]- (NAND Ready/Busy)
                # PSU_IOU_SLCR_MIO_PIN_10_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[10]- (Test Scan Port) = test_scan, Out
                # ut, test_scan_out[10]- (Test Scan Port) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_10_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[10]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[10]- (GPIO bank 0) 1= c
                # n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign
                # l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_mi- (MISO signal) 4= spi1, Output, spi1_
                # o- (MISO signal) 5= ttc2, Input, ttc2_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Outp
                # t, tracedq[8]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_10_L3_SEL                                                  0

                # Configures MIO Pin 10 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180028, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180028 0x000000FE 0x00000002
                # Register : MIO_PIN_11 @ 0XFF18002C</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi_upper[3]- (QSPI Upper Databus) 1= qspi, Output, qspi_mo_uppe
                # [3]- (QSPI Upper Databus)
                # PSU_IOU_SLCR_MIO_PIN_11_L0_SEL                                                  1

                # Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_rb_n[1]- (NAND Ready/Busy)
                # PSU_IOU_SLCR_MIO_PIN_11_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[11]- (Test Scan Port) = test_scan, Out
                # ut, test_scan_out[11]- (Test Scan Port) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_11_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[11]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[11]- (GPIO bank 0) 1= c
                # n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig
                # al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_mo- (MOSI signal) 4= spi1, Input, s
                # i1_si- (MOSI signal) 5= ttc2, Output, ttc2_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial o
                # tput) 7= trace, Output, tracedq[9]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_11_L3_SEL                                                  0

                # Configures MIO Pin 11 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF18002C, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF18002C 0x000000FE 0x00000002
                # Register : MIO_PIN_12 @ 0XFF180030</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Output, qspi_sclk_out_upper- (QSPI Upper Clock)
                # PSU_IOU_SLCR_MIO_PIN_12_L0_SEL                                                  1

                # Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dqs_in- (NAND Strobe) 1= nand, Output, nfc_dqs_out- (NAND Strobe
                # 
                # PSU_IOU_SLCR_MIO_PIN_12_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[12]- (Test Scan Port) = test_scan, Out
                # ut, test_scan_out[12]- (Test Scan Port) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_12_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[12]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[12]- (GPIO bank 0) 1= c
                # n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig
                # al) 3= pjtag, Input, pjtag_tck- (PJTAG TCK) 4= spi0, Input, spi0_sclk_in- (SPI Clock) 4= spi0, Output, spi0_sclk_out- (SPI Cl
                # ck) 5= ttc1, Input, ttc1_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, Output, trac
                # dq[10]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_12_L3_SEL                                                  0

                # Configures MIO Pin 12 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180030, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180030 0x000000FE 0x00000002
                # Register : MIO_PIN_13 @ 0XFF180034</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_13_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_ce[0]- (NAND chip enable)
                # PSU_IOU_SLCR_MIO_PIN_13_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[0]- (8-bit Data bus) = sd0, Output, sdio0_data_out[0]- (8
                # bit Data bus) 2= test_scan, Input, test_scan_in[13]- (Test Scan Port) = test_scan, Output, test_scan_out[13]- (Test Scan Port
                #  3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_13_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[13]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[13]- (GPIO bank 0) 1= c
                # n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign
                # l) 3= pjtag, Input, pjtag_tdi- (PJTAG TDI) 4= spi0, Output, spi0_n_ss_out[2]- (SPI Master Selects) 5= ttc1, Output, ttc1_wave
                # out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7= trace, Output, tracedq[11]- (Trace Port Dat
                # bus)
                # PSU_IOU_SLCR_MIO_PIN_13_L3_SEL                                                  0

                # Configures MIO Pin 13 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180034, 0x000000FEU ,0x00000000U)  */
    mask_write 0XFF180034 0x000000FE 0x00000000
                # Register : MIO_PIN_14 @ 0XFF180038</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_14_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_cle- (NAND Command Latch Enable)
                # PSU_IOU_SLCR_MIO_PIN_14_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[1]- (8-bit Data bus) = sd0, Output, sdio0_data_out[1]- (8
                # bit Data bus) 2= test_scan, Input, test_scan_in[14]- (Test Scan Port) = test_scan, Output, test_scan_out[14]- (Test Scan Port
                #  3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_14_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[14]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[14]- (GPIO bank 0) 1= c
                # n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign
                # l) 3= pjtag, Output, pjtag_tdo- (PJTAG TDO) 4= spi0, Output, spi0_n_ss_out[1]- (SPI Master Selects) 5= ttc0, Input, ttc0_clk_
                # n- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output, tracedq[12]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_14_L3_SEL                                                  2

                # Configures MIO Pin 14 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180038, 0x000000FEU ,0x00000040U)  */
    mask_write 0XFF180038 0x000000FE 0x00000040
                # Register : MIO_PIN_15 @ 0XFF18003C</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_15_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_ale- (NAND Address Latch Enable)
                # PSU_IOU_SLCR_MIO_PIN_15_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[2]- (8-bit Data bus) = sd0, Output, sdio0_data_out[2]- (8
                # bit Data bus) 2= test_scan, Input, test_scan_in[15]- (Test Scan Port) = test_scan, Output, test_scan_out[15]- (Test Scan Port
                #  3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_15_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[15]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[15]- (GPIO bank 0) 1= c
                # n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig
                # al) 3= pjtag, Input, pjtag_tms- (PJTAG TMS) 4= spi0, Input, spi0_n_ss_in- (SPI Master Selects) 4= spi0, Output, spi0_n_ss_out
                # 0]- (SPI Master Selects) 5= ttc0, Output, ttc0_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter seri
                # l output) 7= trace, Output, tracedq[13]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_15_L3_SEL                                                  2

                # Configures MIO Pin 15 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF18003C, 0x000000FEU ,0x00000040U)  */
    mask_write 0XFF18003C 0x000000FE 0x00000040
                # Register : MIO_PIN_16 @ 0XFF180040</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_16_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[0]- (NAND Data Bus) 1= nand, Output, nfc_dq_out[0]- (NAND 
                # ata Bus)
                # PSU_IOU_SLCR_MIO_PIN_16_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[3]- (8-bit Data bus) = sd0, Output, sdio0_data_out[3]- (8
                # bit Data bus) 2= test_scan, Input, test_scan_in[16]- (Test Scan Port) = test_scan, Output, test_scan_out[16]- (Test Scan Port
                #  3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_16_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[16]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[16]- (GPIO bank 0) 1= c
                # n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig
                # al) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi0, Input, spi0_mi- (MISO signal) 4= spi0, Output, spi0
                # so- (MISO signal) 5= ttc3, Input, ttc3_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace
                #  Output, tracedq[14]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_16_L3_SEL                                                  2

                # Configures MIO Pin 16 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180040, 0x000000FEU ,0x00000040U)  */
    mask_write 0XFF180040 0x000000FE 0x00000040
                # Register : MIO_PIN_17 @ 0XFF180044</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_17_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[1]- (NAND Data Bus) 1= nand, Output, nfc_dq_out[1]- (NAND 
                # ata Bus)
                # PSU_IOU_SLCR_MIO_PIN_17_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[4]- (8-bit Data bus) = sd0, Output, sdio0_data_out[4]- (8
                # bit Data bus) 2= test_scan, Input, test_scan_in[17]- (Test Scan Port) = test_scan, Output, test_scan_out[17]- (Test Scan Port
                #  3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_17_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[17]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[17]- (GPIO bank 0) 1= c
                # n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign
                # l) 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi0, Output, spi0_mo- (MOSI signal) 4= spi0, Input, sp
                # 0_si- (MOSI signal) 5= ttc3, Output, ttc3_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input)
                # 7= trace, Output, tracedq[15]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_17_L3_SEL                                                  2

                # Configures MIO Pin 17 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180044, 0x000000FEU ,0x00000040U)  */
    mask_write 0XFF180044 0x000000FE 0x00000040
                # Register : MIO_PIN_18 @ 0XFF180048</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_18_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[2]- (NAND Data Bus) 1= nand, Output, nfc_dq_out[2]- (NAND 
                # ata Bus)
                # PSU_IOU_SLCR_MIO_PIN_18_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[5]- (8-bit Data bus) = sd0, Output, sdio0_data_out[5]- (8
                # bit Data bus) 2= test_scan, Input, test_scan_in[18]- (Test Scan Port) = test_scan, Output, test_scan_out[18]- (Test Scan Port
                #  3= csu, Input, csu_ext_tamper- (CSU Ext Tamper)
                # PSU_IOU_SLCR_MIO_PIN_18_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[18]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[18]- (GPIO bank 0) 1= c
                # n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign
                # l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_mi- (MISO signal) 4= spi1, Output, spi1_
                # o- (MISO signal) 5= ttc2, Input, ttc2_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= Not Used
                # PSU_IOU_SLCR_MIO_PIN_18_L3_SEL                                                  6

                # Configures MIO Pin 18 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180048, 0x000000FEU ,0x000000C0U)  */
    mask_write 0XFF180048 0x000000FE 0x000000C0
                # Register : MIO_PIN_19 @ 0XFF18004C</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_19_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[3]- (NAND Data Bus) 1= nand, Output, nfc_dq_out[3]- (NAND 
                # ata Bus)
                # PSU_IOU_SLCR_MIO_PIN_19_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[6]- (8-bit Data bus) = sd0, Output, sdio0_data_out[6]- (8
                # bit Data bus) 2= test_scan, Input, test_scan_in[19]- (Test Scan Port) = test_scan, Output, test_scan_out[19]- (Test Scan Port
                #  3= csu, Input, csu_ext_tamper- (CSU Ext Tamper)
                # PSU_IOU_SLCR_MIO_PIN_19_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[19]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[19]- (GPIO bank 0) 1= c
                # n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig
                # al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_n_ss_out[2]- (SPI Master Selects) 5
                #  ttc2, Output, ttc2_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial output) 7= Not Used
                # PSU_IOU_SLCR_MIO_PIN_19_L3_SEL                                                  6

                # Configures MIO Pin 19 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF18004C, 0x000000FEU ,0x000000C0U)  */
    mask_write 0XFF18004C 0x000000FE 0x000000C0
                # Register : MIO_PIN_20 @ 0XFF180050</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_20_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[4]- (NAND Data Bus) 1= nand, Output, nfc_dq_out[4]- (NAND 
                # ata Bus)
                # PSU_IOU_SLCR_MIO_PIN_20_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[7]- (8-bit Data bus) = sd0, Output, sdio0_data_out[7]- (8
                # bit Data bus) 2= test_scan, Input, test_scan_in[20]- (Test Scan Port) = test_scan, Output, test_scan_out[20]- (Test Scan Port
                #  3= csu, Input, csu_ext_tamper- (CSU Ext Tamper)
                # PSU_IOU_SLCR_MIO_PIN_20_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[20]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[20]- (GPIO bank 0) 1= c
                # n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig
                # al) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi1, Output, spi1_n_ss_out[1]- (SPI Master Selects) 5= t
                # c1, Input, ttc1_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= Not Used
                # PSU_IOU_SLCR_MIO_PIN_20_L3_SEL                                                  6

                # Configures MIO Pin 20 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180050, 0x000000FEU ,0x000000C0U)  */
    mask_write 0XFF180050 0x000000FE 0x000000C0
                # Register : MIO_PIN_21 @ 0XFF180054</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_21_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[5]- (NAND Data Bus) 1= nand, Output, nfc_dq_out[5]- (NAND 
                # ata Bus)
                # PSU_IOU_SLCR_MIO_PIN_21_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_cmd_in- (Command Indicator) = sd0, Output, sdio0_cmd_out- (Comman
                #  Indicator) 2= test_scan, Input, test_scan_in[21]- (Test Scan Port) = test_scan, Output, test_scan_out[21]- (Test Scan Port) 
                # = csu, Input, csu_ext_tamper- (CSU Ext Tamper)
                # PSU_IOU_SLCR_MIO_PIN_21_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[21]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[21]- (GPIO bank 0) 1= c
                # n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign
                # l) 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi1, Input, spi1_n_ss_in- (SPI Master Selects) 4= spi1
                #  Output, spi1_n_ss_out[0]- (SPI Master Selects) 5= ttc1, Output, ttc1_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- 
                # UART receiver serial input) 7= Not Used
                # PSU_IOU_SLCR_MIO_PIN_21_L3_SEL                                                  6

                # Configures MIO Pin 21 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180054, 0x000000FEU ,0x000000C0U)  */
    mask_write 0XFF180054 0x000000FE 0x000000C0
                # Register : MIO_PIN_22 @ 0XFF180058</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_22_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_we_b- (NAND Write Enable)
                # PSU_IOU_SLCR_MIO_PIN_22_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Output, sdio0_clk_out- (SDSDIO clock) 2= test_scan, Input, test_scan_in[22]-
                # (Test Scan Port) = test_scan, Output, test_scan_out[22]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (CSU Ext Tamper)
                # PSU_IOU_SLCR_MIO_PIN_22_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[22]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[22]- (GPIO bank 0) 1= c
                # n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign
                # l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_sclk_in- (SPI Clock) 4= spi1, Output, sp
                # 1_sclk_out- (SPI Clock) 5= ttc0, Input, ttc0_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= Not 
                # sed
                # PSU_IOU_SLCR_MIO_PIN_22_L3_SEL                                                  0

                # Configures MIO Pin 22 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180058, 0x000000FEU ,0x00000000U)  */
    mask_write 0XFF180058 0x000000FE 0x00000000
                # Register : MIO_PIN_23 @ 0XFF18005C</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_23_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[6]- (NAND Data Bus) 1= nand, Output, nfc_dq_out[6]- (NAND 
                # ata Bus)
                # PSU_IOU_SLCR_MIO_PIN_23_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Output, sdio0_bus_pow- (SD card bus power) 2= test_scan, Input, test_scan_in
                # 23]- (Test Scan Port) = test_scan, Output, test_scan_out[23]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (CSU Ext Tamper
                # 
                # PSU_IOU_SLCR_MIO_PIN_23_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[23]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[23]- (GPIO bank 0) 1= c
                # n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig
                # al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_mo- (MOSI signal) 4= spi1, Input, s
                # i1_si- (MOSI signal) 5= ttc0, Output, ttc0_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial o
                # tput) 7= Not Used
                # PSU_IOU_SLCR_MIO_PIN_23_L3_SEL                                                  0

                # Configures MIO Pin 23 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF18005C, 0x000000FEU ,0x00000000U)  */
    mask_write 0XFF18005C 0x000000FE 0x00000000
                # Register : MIO_PIN_24 @ 0XFF180060</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_24_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[7]- (NAND Data Bus) 1= nand, Output, nfc_dq_out[7]- (NAND 
                # ata Bus)
                # PSU_IOU_SLCR_MIO_PIN_24_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sdio0_cd_n- (SD card detect from connector) 2= test_scan, Input, test
                # scan_in[24]- (Test Scan Port) = test_scan, Output, test_scan_out[24]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (CSU Ex
                #  Tamper)
                # PSU_IOU_SLCR_MIO_PIN_24_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[24]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[24]- (GPIO bank 0) 1= c
                # n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig
                # al) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= Not Used 5= ttc3, Input, ttc3_clk_in- (TTC Clock) 6= ua1,
                # Output, ua1_txd- (UART transmitter serial output) 7= Not Used
                # PSU_IOU_SLCR_MIO_PIN_24_L3_SEL                                                  1

                # Configures MIO Pin 24 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180060, 0x000000FEU ,0x00000020U)  */
    mask_write 0XFF180060 0x000000FE 0x00000020
                # Register : MIO_PIN_25 @ 0XFF180064</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_25_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_re_n- (NAND Read Enable)
                # PSU_IOU_SLCR_MIO_PIN_25_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sdio0_wp- (SD card write protect from connector) 2= test_scan, Input,
                # test_scan_in[25]- (Test Scan Port) = test_scan, Output, test_scan_out[25]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (C
                # U Ext Tamper)
                # PSU_IOU_SLCR_MIO_PIN_25_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[25]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[25]- (GPIO bank 0) 1= c
                # n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign
                # l) 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= Not Used 5= ttc3, Output, ttc3_wave_out- (TTC Waveform 
                # lock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7= Not Used
                # PSU_IOU_SLCR_MIO_PIN_25_L3_SEL                                                  1

                # Configures MIO Pin 25 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180064, 0x000000FEU ,0x00000020U)  */
    mask_write 0XFF180064 0x000000FE 0x00000020
                # Register : MIO_PIN_26 @ 0XFF180068</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Output, gem0_rgmii_tx_clk- (TX RGMII clock)
                # PSU_IOU_SLCR_MIO_PIN_26_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_ce[1]- (NAND chip enable)
                # PSU_IOU_SLCR_MIO_PIN_26_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Input, pmu_gpi[0]- (PMU GPI) 2= test_scan, Input, test_scan_in[26]- (Test Sc
                # n Port) = test_scan, Output, test_scan_out[26]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (CSU Ext Tamper)
                # PSU_IOU_SLCR_MIO_PIN_26_L2_SEL                                                  1

                # Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[0]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[0]- (GPIO bank 1) 1= can
                # , Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL signal
                #  3= pjtag, Input, pjtag_tck- (PJTAG TCK) 4= spi0, Input, spi0_sclk_in- (SPI Clock) 4= spi0, Output, spi0_sclk_out- (SPI Clock
                #  5= ttc2, Input, ttc2_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output, tracedq[4]- 
                # Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_26_L3_SEL                                                  0

                # Configures MIO Pin 26 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180068, 0x000000FEU ,0x00000008U)  */
    mask_write 0XFF180068 0x000000FE 0x00000008
                # Register : MIO_PIN_27 @ 0XFF18006C</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Output, gem0_rgmii_txd[0]- (TX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_27_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_rb_n[0]- (NAND Ready/Busy)
                # PSU_IOU_SLCR_MIO_PIN_27_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Input, pmu_gpi[1]- (PMU GPI) 2= test_scan, Input, test_scan_in[27]- (Test Sc
                # n Port) = test_scan, Output, test_scan_out[27]- (Test Scan Port) 3= dpaux, Input, dp_aux_data_in- (Dp Aux Data) = dpaux, Outp
                # t, dp_aux_data_out- (Dp Aux Data)
                # PSU_IOU_SLCR_MIO_PIN_27_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[1]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[1]- (GPIO bank 1) 1= can
                # , Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA signa
                # ) 3= pjtag, Input, pjtag_tdi- (PJTAG TDI) 4= spi0, Output, spi0_n_ss_out[2]- (SPI Master Selects) 5= ttc2, Output, ttc2_wave_
                # ut- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial output) 7= trace, Output, tracedq[5]- (Trace Port 
                # atabus)
                # PSU_IOU_SLCR_MIO_PIN_27_L3_SEL                                                  0

                # Configures MIO Pin 27 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF18006C, 0x000000FEU ,0x00000000U)  */
    mask_write 0XFF18006C 0x000000FE 0x00000000
                # Register : MIO_PIN_28 @ 0XFF180070</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Output, gem0_rgmii_txd[1]- (TX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_28_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_rb_n[1]- (NAND Ready/Busy)
                # PSU_IOU_SLCR_MIO_PIN_28_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Input, pmu_gpi[2]- (PMU GPI) 2= test_scan, Input, test_scan_in[28]- (Test Sc
                # n Port) = test_scan, Output, test_scan_out[28]- (Test Scan Port) 3= dpaux, Input, dp_hot_plug_detect- (Dp Aux Hot Plug)
                # PSU_IOU_SLCR_MIO_PIN_28_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[2]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[2]- (GPIO bank 1) 1= can
                # , Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL signa
                # ) 3= pjtag, Output, pjtag_tdo- (PJTAG TDO) 4= spi0, Output, spi0_n_ss_out[1]- (SPI Master Selects) 5= ttc1, Input, ttc1_clk_i
                # - (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, Output, tracedq[6]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_28_L3_SEL                                                  0

                # Configures MIO Pin 28 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180070, 0x000000FEU ,0x00000000U)  */
    mask_write 0XFF180070 0x000000FE 0x00000000
                # Register : MIO_PIN_29 @ 0XFF180074</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Output, gem0_rgmii_txd[2]- (TX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_29_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (PCIE Reset signal)
                # PSU_IOU_SLCR_MIO_PIN_29_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Input, pmu_gpi[3]- (PMU GPI) 2= test_scan, Input, test_scan_in[29]- (Test Sc
                # n Port) = test_scan, Output, test_scan_out[29]- (Test Scan Port) 3= dpaux, Input, dp_aux_data_in- (Dp Aux Data) = dpaux, Outp
                # t, dp_aux_data_out- (Dp Aux Data)
                # PSU_IOU_SLCR_MIO_PIN_29_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[3]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[3]- (GPIO bank 1) 1= can
                # , Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA signal
                #  3= pjtag, Input, pjtag_tms- (PJTAG TMS) 4= spi0, Input, spi0_n_ss_in- (SPI Master Selects) 4= spi0, Output, spi0_n_ss_out[0]
                #  (SPI Master Selects) 5= ttc1, Output, ttc1_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial inpu
                # ) 7= trace, Output, tracedq[7]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_29_L3_SEL                                                  0

                # Configures MIO Pin 29 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180074, 0x000000FEU ,0x00000000U)  */
    mask_write 0XFF180074 0x000000FE 0x00000000
                # Register : MIO_PIN_30 @ 0XFF180078</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Output, gem0_rgmii_txd[3]- (TX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_30_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (PCIE Reset signal)
                # PSU_IOU_SLCR_MIO_PIN_30_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Input, pmu_gpi[4]- (PMU GPI) 2= test_scan, Input, test_scan_in[30]- (Test Sc
                # n Port) = test_scan, Output, test_scan_out[30]- (Test Scan Port) 3= dpaux, Input, dp_hot_plug_detect- (Dp Aux Hot Plug)
                # PSU_IOU_SLCR_MIO_PIN_30_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[4]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[4]- (GPIO bank 1) 1= can
                # , Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL signal
                #  3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi0, Input, spi0_mi- (MISO signal) 4= spi0, Output, spi0_so
                #  (MISO signal) 5= ttc0, Input, ttc0_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output
                #  tracedq[8]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_30_L3_SEL                                                  0

                # Configures MIO Pin 30 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180078, 0x000000FEU ,0x00000000U)  */
    mask_write 0XFF180078 0x000000FE 0x00000000
                # Register : MIO_PIN_31 @ 0XFF18007C</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Output, gem0_rgmii_tx_ctl- (TX RGMII control)
                # PSU_IOU_SLCR_MIO_PIN_31_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (PCIE Reset signal)
                # PSU_IOU_SLCR_MIO_PIN_31_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Input, pmu_gpi[5]- (PMU GPI) 2= test_scan, Input, test_scan_in[31]- (Test Sc
                # n Port) = test_scan, Output, test_scan_out[31]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (CSU Ext Tamper)
                # PSU_IOU_SLCR_MIO_PIN_31_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[5]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[5]- (GPIO bank 1) 1= can
                # , Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA signa
                # ) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi0, Output, spi0_mo- (MOSI signal) 4= spi0, Input, spi
                # _si- (MOSI signal) 5= ttc0, Output, ttc0_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial out
                # ut) 7= trace, Output, tracedq[9]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_31_L3_SEL                                                  0

                # Configures MIO Pin 31 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF18007C, 0x000000FEU ,0x00000000U)  */
    mask_write 0XFF18007C 0x000000FE 0x00000000
                # Register : MIO_PIN_32 @ 0XFF180080</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Input, gem0_rgmii_rx_clk- (RX RGMII clock)
                # PSU_IOU_SLCR_MIO_PIN_32_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dqs_in- (NAND Strobe) 1= nand, Output, nfc_dqs_out- (NAND Strobe
                # 
                # PSU_IOU_SLCR_MIO_PIN_32_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Output, pmu_gpo[0]- (PMU GPI) 2= test_scan, Input, test_scan_in[32]- (Test S
                # an Port) = test_scan, Output, test_scan_out[32]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (CSU Ext Tamper)
                # PSU_IOU_SLCR_MIO_PIN_32_L2_SEL                                                  1

                # Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[6]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[6]- (GPIO bank 1) 1= can
                # , Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL signa
                # ) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_sclk_in- (SPI Clock) 4= spi1, Output, spi
                # _sclk_out- (SPI Clock) 5= ttc3, Input, ttc3_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= 
                # race, Output, tracedq[10]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_32_L3_SEL                                                  0

                # Configures MIO Pin 32 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180080, 0x000000FEU ,0x00000008U)  */
    mask_write 0XFF180080 0x000000FE 0x00000008
                # Register : MIO_PIN_33 @ 0XFF180084</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Input, gem0_rgmii_rxd[0]- (RX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_33_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (PCIE Reset signal)
                # PSU_IOU_SLCR_MIO_PIN_33_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Output, pmu_gpo[1]- (PMU GPI) 2= test_scan, Input, test_scan_in[33]- (Test S
                # an Port) = test_scan, Output, test_scan_out[33]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (CSU Ext Tamper)
                # PSU_IOU_SLCR_MIO_PIN_33_L2_SEL                                                  1

                # Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[7]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[7]- (GPIO bank 1) 1= can
                # , Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA signal
                #  3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_n_ss_out[2]- (SPI Master Selects) 5= t
                # c3, Output, ttc3_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7= trace, Output, traced
                # [11]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_33_L3_SEL                                                  0

                # Configures MIO Pin 33 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180084, 0x000000FEU ,0x00000008U)  */
    mask_write 0XFF180084 0x000000FE 0x00000008
                # Register : MIO_PIN_34 @ 0XFF180088</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Input, gem0_rgmii_rxd[1]- (RX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_34_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (PCIE Reset signal)
                # PSU_IOU_SLCR_MIO_PIN_34_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Output, pmu_gpo[2]- (PMU GPI) 2= test_scan, Input, test_scan_in[34]- (Test S
                # an Port) = test_scan, Output, test_scan_out[34]- (Test Scan Port) 3= dpaux, Input, dp_aux_data_in- (Dp Aux Data) = dpaux, Out
                # ut, dp_aux_data_out- (Dp Aux Data)
                # PSU_IOU_SLCR_MIO_PIN_34_L2_SEL                                                  1

                # Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[8]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[8]- (GPIO bank 1) 1= can
                # , Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL signal
                #  3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi1, Output, spi1_n_ss_out[1]- (SPI Master Selects) 5= ttc2
                #  Input, ttc2_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output, tracedq[12]- (Trace P
                # rt Databus)
                # PSU_IOU_SLCR_MIO_PIN_34_L3_SEL                                                  0

                # Configures MIO Pin 34 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180088, 0x000000FEU ,0x00000008U)  */
    mask_write 0XFF180088 0x000000FE 0x00000008
                # Register : MIO_PIN_35 @ 0XFF18008C</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Input, gem0_rgmii_rxd[2]- (RX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_35_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (PCIE Reset signal)
                # PSU_IOU_SLCR_MIO_PIN_35_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Output, pmu_gpo[3]- (PMU GPI) 2= test_scan, Input, test_scan_in[35]- (Test S
                # an Port) = test_scan, Output, test_scan_out[35]- (Test Scan Port) 3= dpaux, Input, dp_hot_plug_detect- (Dp Aux Hot Plug)
                # PSU_IOU_SLCR_MIO_PIN_35_L2_SEL                                                  1

                # Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[9]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[9]- (GPIO bank 1) 1= can
                # , Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA signa
                # ) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi1, Input, spi1_n_ss_in- (SPI Master Selects) 4= spi1,
                # Output, spi1_n_ss_out[0]- (SPI Master Selects) 5= ttc2, Output, ttc2_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- 
                # UART transmitter serial output) 7= trace, Output, tracedq[13]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_35_L3_SEL                                                  0

                # Configures MIO Pin 35 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF18008C, 0x000000FEU ,0x00000008U)  */
    mask_write 0XFF18008C 0x000000FE 0x00000008
                # Register : MIO_PIN_36 @ 0XFF180090</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Input, gem0_rgmii_rxd[3]- (RX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_36_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (PCIE Reset signal)
                # PSU_IOU_SLCR_MIO_PIN_36_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Output, pmu_gpo[4]- (PMU GPI) 2= test_scan, Input, test_scan_in[36]- (Test S
                # an Port) = test_scan, Output, test_scan_out[36]- (Test Scan Port) 3= dpaux, Input, dp_aux_data_in- (Dp Aux Data) = dpaux, Out
                # ut, dp_aux_data_out- (Dp Aux Data)
                # PSU_IOU_SLCR_MIO_PIN_36_L2_SEL                                                  1

                # Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[10]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[10]- (GPIO bank 1) 1= c
                # n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig
                # al) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_mi- (MISO signal) 4= spi1, Output, spi1
                # so- (MISO signal) 5= ttc1, Input, ttc1_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace
                #  Output, tracedq[14]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_36_L3_SEL                                                  0

                # Configures MIO Pin 36 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180090, 0x000000FEU ,0x00000008U)  */
    mask_write 0XFF180090 0x000000FE 0x00000008
                # Register : MIO_PIN_37 @ 0XFF180094</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Input, gem0_rgmii_rx_ctl- (RX RGMII control )
                # PSU_IOU_SLCR_MIO_PIN_37_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (PCIE Reset signal)
                # PSU_IOU_SLCR_MIO_PIN_37_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Output, pmu_gpo[5]- (PMU GPI) 2= test_scan, Input, test_scan_in[37]- (Test S
                # an Port) = test_scan, Output, test_scan_out[37]- (Test Scan Port) 3= dpaux, Input, dp_hot_plug_detect- (Dp Aux Hot Plug)
                # PSU_IOU_SLCR_MIO_PIN_37_L2_SEL                                                  1

                # Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[11]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[11]- (GPIO bank 1) 1= c
                # n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign
                # l) 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_mo- (MOSI signal) 4= spi1, Input, sp
                # 1_si- (MOSI signal) 5= ttc1, Output, ttc1_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input)
                # 7= trace, Output, tracedq[15]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_37_L3_SEL                                                  0

                # Configures MIO Pin 37 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180094, 0x000000FEU ,0x00000008U)  */
    mask_write 0XFF180094 0x000000FE 0x00000008
                # Register : MIO_PIN_38 @ 0XFF180098</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Output, gem1_rgmii_tx_clk- (TX RGMII clock)
                # PSU_IOU_SLCR_MIO_PIN_38_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_38_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Output, sdio0_clk_out- (SDSDIO clock) 2= Not Used 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_38_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[12]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[12]- (GPIO bank 1) 1= c
                # n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign
                # l) 3= pjtag, Input, pjtag_tck- (PJTAG TCK) 4= spi0, Input, spi0_sclk_in- (SPI Clock) 4= spi0, Output, spi0_sclk_out- (SPI Clo
                # k) 5= ttc0, Input, ttc0_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output, trace_clk-
                # (Trace Port Clock)
                # PSU_IOU_SLCR_MIO_PIN_38_L3_SEL                                                  0

                # Configures MIO Pin 38 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180098, 0x000000FEU ,0x00000000U)  */
    mask_write 0XFF180098 0x000000FE 0x00000000
                # Register : MIO_PIN_39 @ 0XFF18009C</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Output, gem1_rgmii_txd[0]- (TX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_39_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_39_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sdio0_cd_n- (SD card detect from connector) 2= sd1, Input, sd1_data_i
                # [4]- (8-bit Data bus) = sd1, Output, sdio1_data_out[4]- (8-bit Data bus) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_39_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[13]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[13]- (GPIO bank 1) 1= c
                # n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig
                # al) 3= pjtag, Input, pjtag_tdi- (PJTAG TDI) 4= spi0, Output, spi0_n_ss_out[2]- (SPI Master Selects) 5= ttc0, Output, ttc0_wav
                # _out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial output) 7= trace, Output, trace_ctl- (Trace Port
                # Control Signal)
                # PSU_IOU_SLCR_MIO_PIN_39_L3_SEL                                                  0

                # Configures MIO Pin 39 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF18009C, 0x000000FEU ,0x00000000U)  */
    mask_write 0XFF18009C 0x000000FE 0x00000000
                # Register : MIO_PIN_40 @ 0XFF1800A0</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Output, gem1_rgmii_txd[1]- (TX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_40_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_40_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_cmd_in- (Command Indicator) = sd0, Output, sdio0_cmd_out- (Comman
                #  Indicator) 2= sd1, Input, sd1_data_in[5]- (8-bit Data bus) = sd1, Output, sdio1_data_out[5]- (8-bit Data bus) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_40_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[14]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[14]- (GPIO bank 1) 1= c
                # n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig
                # al) 3= pjtag, Output, pjtag_tdo- (PJTAG TDO) 4= spi0, Output, spi0_n_ss_out[1]- (SPI Master Selects) 5= ttc3, Input, ttc3_clk
                # in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, Output, tracedq[0]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_40_L3_SEL                                                  0

                # Configures MIO Pin 40 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF1800A0, 0x000000FEU ,0x00000000U)  */
    mask_write 0XFF1800A0 0x000000FE 0x00000000
                # Register : MIO_PIN_41 @ 0XFF1800A4</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Output, gem1_rgmii_txd[2]- (TX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_41_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_41_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[0]- (8-bit Data bus) = sd0, Output, sdio0_data_out[0]- (8
                # bit Data bus) 2= sd1, Input, sd1_data_in[6]- (8-bit Data bus) = sd1, Output, sdio1_data_out[6]- (8-bit Data bus) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_41_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[15]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[15]- (GPIO bank 1) 1= c
                # n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign
                # l) 3= pjtag, Input, pjtag_tms- (PJTAG TMS) 4= spi0, Input, spi0_n_ss_in- (SPI Master Selects) 4= spi0, Output, spi0_n_ss_out[
                # ]- (SPI Master Selects) 5= ttc3, Output, ttc3_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial in
                # ut) 7= trace, Output, tracedq[1]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_41_L3_SEL                                                  0

                # Configures MIO Pin 41 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF1800A4, 0x000000FEU ,0x00000000U)  */
    mask_write 0XFF1800A4 0x000000FE 0x00000000
                # Register : MIO_PIN_42 @ 0XFF1800A8</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Output, gem1_rgmii_txd[3]- (TX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_42_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_42_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[1]- (8-bit Data bus) = sd0, Output, sdio0_data_out[1]- (8
                # bit Data bus) 2= sd1, Input, sd1_data_in[7]- (8-bit Data bus) = sd1, Output, sdio1_data_out[7]- (8-bit Data bus) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_42_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[16]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[16]- (GPIO bank 1) 1= c
                # n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign
                # l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi0, Input, spi0_mi- (MISO signal) 4= spi0, Output, spi0_
                # o- (MISO signal) 5= ttc2, Input, ttc2_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Outp
                # t, tracedq[2]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_42_L3_SEL                                                  0

                # Configures MIO Pin 42 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF1800A8, 0x000000FEU ,0x00000000U)  */
    mask_write 0XFF1800A8 0x000000FE 0x00000000
                # Register : MIO_PIN_43 @ 0XFF1800AC</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Output, gem1_rgmii_tx_ctl- (TX RGMII control)
                # PSU_IOU_SLCR_MIO_PIN_43_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_43_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[2]- (8-bit Data bus) = sd0, Output, sdio0_data_out[2]- (8
                # bit Data bus) 2= sd1, Output, sdio1_bus_pow- (SD card bus power) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_43_L2_SEL                                                  2

                # Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[17]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[17]- (GPIO bank 1) 1= c
                # n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig
                # al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi0, Output, spi0_mo- (MOSI signal) 4= spi0, Input, s
                # i0_si- (MOSI signal) 5= ttc2, Output, ttc2_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial o
                # tput) 7= trace, Output, tracedq[3]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_43_L3_SEL                                                  0

                # Configures MIO Pin 43 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF1800AC, 0x000000FEU ,0x00000010U)  */
    mask_write 0XFF1800AC 0x000000FE 0x00000010
                # Register : MIO_PIN_44 @ 0XFF1800B0</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Input, gem1_rgmii_rx_clk- (RX RGMII clock)
                # PSU_IOU_SLCR_MIO_PIN_44_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_44_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[3]- (8-bit Data bus) = sd0, Output, sdio0_data_out[3]- (8
                # bit Data bus) 2= sd1, Input, sdio1_wp- (SD card write protect from connector) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_44_L2_SEL                                                  2

                # Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[18]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[18]- (GPIO bank 1) 1= c
                # n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig
                # al) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_sclk_in- (SPI Clock) 4= spi1, Output, s
                # i1_sclk_out- (SPI Clock) 5= ttc1, Input, ttc1_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7
                #  Not Used
                # PSU_IOU_SLCR_MIO_PIN_44_L3_SEL                                                  0

                # Configures MIO Pin 44 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF1800B0, 0x000000FEU ,0x00000010U)  */
    mask_write 0XFF1800B0 0x000000FE 0x00000010
                # Register : MIO_PIN_45 @ 0XFF1800B4</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Input, gem1_rgmii_rxd[0]- (RX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_45_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_45_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[4]- (8-bit Data bus) = sd0, Output, sdio0_data_out[4]- (8
                # bit Data bus) 2= sd1, Input, sdio1_cd_n- (SD card detect from connector) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_45_L2_SEL                                                  2

                # Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[19]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[19]- (GPIO bank 1) 1= c
                # n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign
                # l) 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_n_ss_out[2]- (SPI Master Selects) 5=
                # ttc1, Output, ttc1_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7= Not Used
                # PSU_IOU_SLCR_MIO_PIN_45_L3_SEL                                                  0

                # Configures MIO Pin 45 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF1800B4, 0x000000FEU ,0x00000010U)  */
    mask_write 0XFF1800B4 0x000000FE 0x00000010
                # Register : MIO_PIN_46 @ 0XFF1800B8</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Input, gem1_rgmii_rxd[1]- (RX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_46_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_46_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[5]- (8-bit Data bus) = sd0, Output, sdio0_data_out[5]- (8
                # bit Data bus) 2= sd1, Input, sd1_data_in[0]- (8-bit Data bus) = sd1, Output, sdio1_data_out[0]- (8-bit Data bus) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_46_L2_SEL                                                  2

                # Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[20]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[20]- (GPIO bank 1) 1= c
                # n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign
                # l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi1, Output, spi1_n_ss_out[1]- (SPI Master Selects) 5= tt
                # 0, Input, ttc0_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= Not Used
                # PSU_IOU_SLCR_MIO_PIN_46_L3_SEL                                                  0

                # Configures MIO Pin 46 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF1800B8, 0x000000FEU ,0x00000010U)  */
    mask_write 0XFF1800B8 0x000000FE 0x00000010
                # Register : MIO_PIN_47 @ 0XFF1800BC</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Input, gem1_rgmii_rxd[2]- (RX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_47_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_47_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[6]- (8-bit Data bus) = sd0, Output, sdio0_data_out[6]- (8
                # bit Data bus) 2= sd1, Input, sd1_data_in[1]- (8-bit Data bus) = sd1, Output, sdio1_data_out[1]- (8-bit Data bus) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_47_L2_SEL                                                  2

                # Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[21]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[21]- (GPIO bank 1) 1= c
                # n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig
                # al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi1, Input, spi1_n_ss_in- (SPI Master Selects) 4= spi
                # , Output, spi1_n_ss_out[0]- (SPI Master Selects) 5= ttc0, Output, ttc0_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd
                #  (UART transmitter serial output) 7= Not Used
                # PSU_IOU_SLCR_MIO_PIN_47_L3_SEL                                                  0

                # Configures MIO Pin 47 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF1800BC, 0x000000FEU ,0x00000010U)  */
    mask_write 0XFF1800BC 0x000000FE 0x00000010
                # Register : MIO_PIN_48 @ 0XFF1800C0</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Input, gem1_rgmii_rxd[3]- (RX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_48_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_48_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[7]- (8-bit Data bus) = sd0, Output, sdio0_data_out[7]- (8
                # bit Data bus) 2= sd1, Input, sd1_data_in[2]- (8-bit Data bus) = sd1, Output, sdio1_data_out[2]- (8-bit Data bus) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_48_L2_SEL                                                  2

                # Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[22]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[22]- (GPIO bank 1) 1= c
                # n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig
                # al) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_mi- (MISO signal) 4= spi1, Output, spi1
                # so- (MISO signal) 5= ttc3, Input, ttc3_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= Not U
                # ed
                # PSU_IOU_SLCR_MIO_PIN_48_L3_SEL                                                  0

                # Configures MIO Pin 48 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF1800C0, 0x000000FEU ,0x00000010U)  */
    mask_write 0XFF1800C0 0x000000FE 0x00000010
                # Register : MIO_PIN_49 @ 0XFF1800C4</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Input, gem1_rgmii_rx_ctl- (RX RGMII control )
                # PSU_IOU_SLCR_MIO_PIN_49_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_49_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Output, sdio0_bus_pow- (SD card bus power) 2= sd1, Input, sd1_data_in[3]- (8
                # bit Data bus) = sd1, Output, sdio1_data_out[3]- (8-bit Data bus) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_49_L2_SEL                                                  2

                # Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[23]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[23]- (GPIO bank 1) 1= c
                # n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign
                # l) 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_mo- (MOSI signal) 4= spi1, Input, sp
                # 1_si- (MOSI signal) 5= ttc3, Output, ttc3_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input)
                # 7= Not Used
                # PSU_IOU_SLCR_MIO_PIN_49_L3_SEL                                                  0

                # Configures MIO Pin 49 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF1800C4, 0x000000FEU ,0x00000010U)  */
    mask_write 0XFF1800C4 0x000000FE 0x00000010
                # Register : MIO_PIN_50 @ 0XFF1800C8</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem_tsu, Input, gem_tsu_clk- (TSU clock)
                # PSU_IOU_SLCR_MIO_PIN_50_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_50_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sdio0_wp- (SD card write protect from connector) 2= sd1, Input, sd1_c
                # d_in- (Command Indicator) = sd1, Output, sdio1_cmd_out- (Command Indicator) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_50_L2_SEL                                                  2

                # Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[24]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[24]- (GPIO bank 1) 1= c
                # n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign
                # l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= mdio1, Output, gem1_mdc- (MDIO Clock) 5= ttc2, Input, ttc2
                # clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= Not Used
                # PSU_IOU_SLCR_MIO_PIN_50_L3_SEL                                                  0

                # Configures MIO Pin 50 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF1800C8, 0x000000FEU ,0x00000010U)  */
    mask_write 0XFF1800C8 0x000000FE 0x00000010
                # Register : MIO_PIN_51 @ 0XFF1800CC</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem_tsu, Input, gem_tsu_clk- (TSU clock)
                # PSU_IOU_SLCR_MIO_PIN_51_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_51_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= sd1, Output, sdio1_clk_out- (SDSDIO clock) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_51_L2_SEL                                                  2

                # Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[25]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[25]- (GPIO bank 1) 1= c
                # n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig
                # al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= mdio1, Input, gem1_mdio_in- (MDIO Data) 4= mdio1, Outp
                # t, gem1_mdio_out- (MDIO Data) 5= ttc2, Output, ttc2_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter
                # serial output) 7= Not Used
                # PSU_IOU_SLCR_MIO_PIN_51_L3_SEL                                                  0

                # Configures MIO Pin 51 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF1800CC, 0x000000FEU ,0x00000010U)  */
    mask_write 0XFF1800CC 0x000000FE 0x00000010
                # Register : MIO_PIN_52 @ 0XFF1800D0</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Output, gem2_rgmii_tx_clk- (TX RGMII clock)
                # PSU_IOU_SLCR_MIO_PIN_52_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_clk_in- (ULPI Clock)
                # PSU_IOU_SLCR_MIO_PIN_52_L1_SEL                                                  1

                # Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_52_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[0]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[0]- (GPIO bank 2) 1= can
                # , Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL signa
                # ) 3= pjtag, Input, pjtag_tck- (PJTAG TCK) 4= spi0, Input, spi0_sclk_in- (SPI Clock) 4= spi0, Output, spi0_sclk_out- (SPI Cloc
                # ) 5= ttc1, Input, ttc1_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, Output, trace_
                # lk- (Trace Port Clock)
                # PSU_IOU_SLCR_MIO_PIN_52_L3_SEL                                                  0

                # Configures MIO Pin 52 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF1800D0, 0x000000FEU ,0x00000004U)  */
    mask_write 0XFF1800D0 0x000000FE 0x00000004
                # Register : MIO_PIN_53 @ 0XFF1800D4</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Output, gem2_rgmii_txd[0]- (TX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_53_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_dir- (Data bus direction control)
                # PSU_IOU_SLCR_MIO_PIN_53_L1_SEL                                                  1

                # Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_53_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[1]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[1]- (GPIO bank 2) 1= can
                # , Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA signal
                #  3= pjtag, Input, pjtag_tdi- (PJTAG TDI) 4= spi0, Output, spi0_n_ss_out[2]- (SPI Master Selects) 5= ttc1, Output, ttc1_wave_o
                # t- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7= trace, Output, trace_ctl- (Trace Port Control
                # Signal)
                # PSU_IOU_SLCR_MIO_PIN_53_L3_SEL                                                  0

                # Configures MIO Pin 53 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF1800D4, 0x000000FEU ,0x00000004U)  */
    mask_write 0XFF1800D4 0x000000FE 0x00000004
                # Register : MIO_PIN_54 @ 0XFF1800D8</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Output, gem2_rgmii_txd[1]- (TX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_54_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_data[2]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_
                # ata[2]- (ULPI data bus)
                # PSU_IOU_SLCR_MIO_PIN_54_L1_SEL                                                  1

                # Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_54_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[2]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[2]- (GPIO bank 2) 1= can
                # , Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL signal
                #  3= pjtag, Output, pjtag_tdo- (PJTAG TDO) 4= spi0, Output, spi0_n_ss_out[1]- (SPI Master Selects) 5= ttc0, Input, ttc0_clk_in
                #  (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output, tracedq[0]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_54_L3_SEL                                                  0

                # Configures MIO Pin 54 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF1800D8, 0x000000FEU ,0x00000004U)  */
    mask_write 0XFF1800D8 0x000000FE 0x00000004
                # Register : MIO_PIN_55 @ 0XFF1800DC</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Output, gem2_rgmii_txd[2]- (TX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_55_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_nxt- (Data flow control signal from the PHY)
                # PSU_IOU_SLCR_MIO_PIN_55_L1_SEL                                                  1

                # Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_55_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[3]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[3]- (GPIO bank 2) 1= can
                # , Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA signa
                # ) 3= pjtag, Input, pjtag_tms- (PJTAG TMS) 4= spi0, Input, spi0_n_ss_in- (SPI Master Selects) 4= spi0, Output, spi0_n_ss_out[0
                # - (SPI Master Selects) 5= ttc0, Output, ttc0_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial
                # output) 7= trace, Output, tracedq[1]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_55_L3_SEL                                                  0

                # Configures MIO Pin 55 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF1800DC, 0x000000FEU ,0x00000004U)  */
    mask_write 0XFF1800DC 0x000000FE 0x00000004
                # Register : MIO_PIN_56 @ 0XFF1800E0</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Output, gem2_rgmii_txd[3]- (TX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_56_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_data[0]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_
                # ata[0]- (ULPI data bus)
                # PSU_IOU_SLCR_MIO_PIN_56_L1_SEL                                                  1

                # Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_56_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[4]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[4]- (GPIO bank 2) 1= can
                # , Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL signa
                # ) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi0, Input, spi0_mi- (MISO signal) 4= spi0, Output, spi0_s
                # - (MISO signal) 5= ttc3, Input, ttc3_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, 
                # utput, tracedq[2]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_56_L3_SEL                                                  0

                # Configures MIO Pin 56 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF1800E0, 0x000000FEU ,0x00000004U)  */
    mask_write 0XFF1800E0 0x000000FE 0x00000004
                # Register : MIO_PIN_57 @ 0XFF1800E4</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Output, gem2_rgmii_tx_ctl- (TX RGMII control)
                # PSU_IOU_SLCR_MIO_PIN_57_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_data[1]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_
                # ata[1]- (ULPI data bus)
                # PSU_IOU_SLCR_MIO_PIN_57_L1_SEL                                                  1

                # Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_57_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[5]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[5]- (GPIO bank 2) 1= can
                # , Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA signal
                #  3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi0, Output, spi0_mo- (MOSI signal) 4= spi0, Input, spi0
                # si- (MOSI signal) 5= ttc3, Output, ttc3_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7
                #  trace, Output, tracedq[3]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_57_L3_SEL                                                  0

                # Configures MIO Pin 57 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF1800E4, 0x000000FEU ,0x00000004U)  */
    mask_write 0XFF1800E4 0x000000FE 0x00000004
                # Register : MIO_PIN_58 @ 0XFF1800E8</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Input, gem2_rgmii_rx_clk- (RX RGMII clock)
                # PSU_IOU_SLCR_MIO_PIN_58_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Output, usb0_ulpi_stp- (Asserted to end or interrupt transfers)
                # PSU_IOU_SLCR_MIO_PIN_58_L1_SEL                                                  1

                # Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_58_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[6]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[6]- (GPIO bank 2) 1= can
                # , Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL signal
                #  3= pjtag, Input, pjtag_tck- (PJTAG TCK) 4= spi1, Input, spi1_sclk_in- (SPI Clock) 4= spi1, Output, spi1_sclk_out- (SPI Clock
                #  5= ttc2, Input, ttc2_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output, tracedq[4]- 
                # Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_58_L3_SEL                                                  0

                # Configures MIO Pin 58 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF1800E8, 0x000000FEU ,0x00000004U)  */
    mask_write 0XFF1800E8 0x000000FE 0x00000004
                # Register : MIO_PIN_59 @ 0XFF1800EC</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Input, gem2_rgmii_rxd[0]- (RX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_59_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_data[3]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_
                # ata[3]- (ULPI data bus)
                # PSU_IOU_SLCR_MIO_PIN_59_L1_SEL                                                  1

                # Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_59_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[7]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[7]- (GPIO bank 2) 1= can
                # , Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA signa
                # ) 3= pjtag, Input, pjtag_tdi- (PJTAG TDI) 4= spi1, Output, spi1_n_ss_out[2]- (SPI Master Selects) 5= ttc2, Output, ttc2_wave_
                # ut- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial output) 7= trace, Output, tracedq[5]- (Trace Port 
                # atabus)
                # PSU_IOU_SLCR_MIO_PIN_59_L3_SEL                                                  0

                # Configures MIO Pin 59 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF1800EC, 0x000000FEU ,0x00000004U)  */
    mask_write 0XFF1800EC 0x000000FE 0x00000004
                # Register : MIO_PIN_60 @ 0XFF1800F0</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Input, gem2_rgmii_rxd[1]- (RX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_60_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_data[4]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_
                # ata[4]- (ULPI data bus)
                # PSU_IOU_SLCR_MIO_PIN_60_L1_SEL                                                  1

                # Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_60_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[8]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[8]- (GPIO bank 2) 1= can
                # , Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL signa
                # ) 3= pjtag, Output, pjtag_tdo- (PJTAG TDO) 4= spi1, Output, spi1_n_ss_out[1]- (SPI Master Selects) 5= ttc1, Input, ttc1_clk_i
                # - (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, Output, tracedq[6]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_60_L3_SEL                                                  0

                # Configures MIO Pin 60 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF1800F0, 0x000000FEU ,0x00000004U)  */
    mask_write 0XFF1800F0 0x000000FE 0x00000004
                # Register : MIO_PIN_61 @ 0XFF1800F4</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Input, gem2_rgmii_rxd[2]- (RX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_61_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_data[5]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_
                # ata[5]- (ULPI data bus)
                # PSU_IOU_SLCR_MIO_PIN_61_L1_SEL                                                  1

                # Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_61_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[9]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[9]- (GPIO bank 2) 1= can
                # , Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA signal
                #  3= pjtag, Input, pjtag_tms- (PJTAG TMS) 4= spi1, Input, spi1_n_ss_in- (SPI Master Selects) 4= spi1, Output, spi1_n_ss_out[0]
                #  (SPI Master Selects) 5= ttc1, Output, ttc1_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial inpu
                # ) 7= trace, Output, tracedq[7]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_61_L3_SEL                                                  0

                # Configures MIO Pin 61 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF1800F4, 0x000000FEU ,0x00000004U)  */
    mask_write 0XFF1800F4 0x000000FE 0x00000004
                # Register : MIO_PIN_62 @ 0XFF1800F8</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Input, gem2_rgmii_rxd[3]- (RX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_62_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_data[6]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_
                # ata[6]- (ULPI data bus)
                # PSU_IOU_SLCR_MIO_PIN_62_L1_SEL                                                  1

                # Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_62_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[10]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[10]- (GPIO bank 2) 1= c
                # n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign
                # l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_mi- (MISO signal) 4= spi1, Output, spi1_
                # o- (MISO signal) 5= ttc0, Input, ttc0_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Outp
                # t, tracedq[8]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_62_L3_SEL                                                  0

                # Configures MIO Pin 62 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF1800F8, 0x000000FEU ,0x00000004U)  */
    mask_write 0XFF1800F8 0x000000FE 0x00000004
                # Register : MIO_PIN_63 @ 0XFF1800FC</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Input, gem2_rgmii_rx_ctl- (RX RGMII control )
                # PSU_IOU_SLCR_MIO_PIN_63_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_data[7]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_
                # ata[7]- (ULPI data bus)
                # PSU_IOU_SLCR_MIO_PIN_63_L1_SEL                                                  1

                # Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_63_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[11]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[11]- (GPIO bank 2) 1= c
                # n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig
                # al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_mo- (MOSI signal) 4= spi1, Input, s
                # i1_si- (MOSI signal) 5= ttc0, Output, ttc0_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial o
                # tput) 7= trace, Output, tracedq[9]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_63_L3_SEL                                                  0

                # Configures MIO Pin 63 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF1800FC, 0x000000FEU ,0x00000004U)  */
    mask_write 0XFF1800FC 0x000000FE 0x00000004
                # Register : MIO_PIN_64 @ 0XFF180100</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Output, gem3_rgmii_tx_clk- (TX RGMII clock)
                # PSU_IOU_SLCR_MIO_PIN_64_L0_SEL                                                  1

                # Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_clk_in- (ULPI Clock)
                # PSU_IOU_SLCR_MIO_PIN_64_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Output, sdio0_clk_out- (SDSDIO clock) 2= Not Used 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_64_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[12]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[12]- (GPIO bank 2) 1= c
                # n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig
                # al) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi0, Input, spi0_sclk_in- (SPI Clock) 4= spi0, Output, s
                # i0_sclk_out- (SPI Clock) 5= ttc3, Input, ttc3_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7
                #  trace, Output, tracedq[10]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_64_L3_SEL                                                  0

                # Configures MIO Pin 64 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180100, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180100 0x000000FE 0x00000002
                # Register : MIO_PIN_65 @ 0XFF180104</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Output, gem3_rgmii_txd[0]- (TX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_65_L0_SEL                                                  1

                # Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_dir- (Data bus direction control)
                # PSU_IOU_SLCR_MIO_PIN_65_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sdio0_cd_n- (SD card detect from connector) 2= Not Used 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_65_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[13]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[13]- (GPIO bank 2) 1= c
                # n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign
                # l) 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi0, Output, spi0_n_ss_out[2]- (SPI Master Selects) 5=
                # ttc3, Output, ttc3_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7= trace, Output, trac
                # dq[11]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_65_L3_SEL                                                  0

                # Configures MIO Pin 65 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180104, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180104 0x000000FE 0x00000002
                # Register : MIO_PIN_66 @ 0XFF180108</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Output, gem3_rgmii_txd[1]- (TX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_66_L0_SEL                                                  1

                # Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_data[2]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_
                # ata[2]- (ULPI data bus)
                # PSU_IOU_SLCR_MIO_PIN_66_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_cmd_in- (Command Indicator) = sd0, Output, sdio0_cmd_out- (Comman
                #  Indicator) 2= Not Used 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_66_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[14]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[14]- (GPIO bank 2) 1= c
                # n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign
                # l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi0, Output, spi0_n_ss_out[1]- (SPI Master Selects) 5= tt
                # 2, Input, ttc2_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output, tracedq[12]- (Trace
                # Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_66_L3_SEL                                                  0

                # Configures MIO Pin 66 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180108, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180108 0x000000FE 0x00000002
                # Register : MIO_PIN_67 @ 0XFF18010C</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Output, gem3_rgmii_txd[2]- (TX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_67_L0_SEL                                                  1

                # Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_nxt- (Data flow control signal from the PHY)
                # PSU_IOU_SLCR_MIO_PIN_67_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[0]- (8-bit Data bus) = sd0, Output, sdio0_data_out[0]- (8
                # bit Data bus) 2= Not Used 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_67_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[15]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[15]- (GPIO bank 2) 1= c
                # n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig
                # al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi0, Input, spi0_n_ss_in- (SPI Master Selects) 4= spi
                # , Output, spi0_n_ss_out[0]- (SPI Master Selects) 5= ttc2, Output, ttc2_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd
                #  (UART transmitter serial output) 7= trace, Output, tracedq[13]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_67_L3_SEL                                                  0

                # Configures MIO Pin 67 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF18010C, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF18010C 0x000000FE 0x00000002
                # Register : MIO_PIN_68 @ 0XFF180110</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Output, gem3_rgmii_txd[3]- (TX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_68_L0_SEL                                                  1

                # Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_data[0]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_
                # ata[0]- (ULPI data bus)
                # PSU_IOU_SLCR_MIO_PIN_68_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[1]- (8-bit Data bus) = sd0, Output, sdio0_data_out[1]- (8
                # bit Data bus) 2= Not Used 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_68_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[16]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[16]- (GPIO bank 2) 1= c
                # n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig
                # al) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi0, Input, spi0_mi- (MISO signal) 4= spi0, Output, spi0
                # so- (MISO signal) 5= ttc1, Input, ttc1_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace
                #  Output, tracedq[14]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_68_L3_SEL                                                  0

                # Configures MIO Pin 68 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180110, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180110 0x000000FE 0x00000002
                # Register : MIO_PIN_69 @ 0XFF180114</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Output, gem3_rgmii_tx_ctl- (TX RGMII control)
                # PSU_IOU_SLCR_MIO_PIN_69_L0_SEL                                                  1

                # Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_data[1]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_
                # ata[1]- (ULPI data bus)
                # PSU_IOU_SLCR_MIO_PIN_69_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[2]- (8-bit Data bus) = sd0, Output, sdio0_data_out[2]- (8
                # bit Data bus) 2= sd1, Input, sdio1_wp- (SD card write protect from connector) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_69_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[17]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[17]- (GPIO bank 2) 1= c
                # n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign
                # l) 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi0, Output, spi0_mo- (MOSI signal) 4= spi0, Input, sp
                # 0_si- (MOSI signal) 5= ttc1, Output, ttc1_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input)
                # 7= trace, Output, tracedq[15]- (Trace Port Databus)
                # PSU_IOU_SLCR_MIO_PIN_69_L3_SEL                                                  0

                # Configures MIO Pin 69 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180114, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180114 0x000000FE 0x00000002
                # Register : MIO_PIN_70 @ 0XFF180118</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Input, gem3_rgmii_rx_clk- (RX RGMII clock)
                # PSU_IOU_SLCR_MIO_PIN_70_L0_SEL                                                  1

                # Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Output, usb1_ulpi_stp- (Asserted to end or interrupt transfers)
                # PSU_IOU_SLCR_MIO_PIN_70_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[3]- (8-bit Data bus) = sd0, Output, sdio0_data_out[3]- (8
                # bit Data bus) 2= sd1, Output, sdio1_bus_pow- (SD card bus power) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_70_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[18]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[18]- (GPIO bank 2) 1= c
                # n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign
                # l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_sclk_in- (SPI Clock) 4= spi1, Output, sp
                # 1_sclk_out- (SPI Clock) 5= ttc0, Input, ttc0_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= Not 
                # sed
                # PSU_IOU_SLCR_MIO_PIN_70_L3_SEL                                                  0

                # Configures MIO Pin 70 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180118, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180118 0x000000FE 0x00000002
                # Register : MIO_PIN_71 @ 0XFF18011C</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Input, gem3_rgmii_rxd[0]- (RX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_71_L0_SEL                                                  1

                # Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_data[3]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_
                # ata[3]- (ULPI data bus)
                # PSU_IOU_SLCR_MIO_PIN_71_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[4]- (8-bit Data bus) = sd0, Output, sdio0_data_out[4]- (8
                # bit Data bus) 2= sd1, Input, sd1_data_in[0]- (8-bit Data bus) = sd1, Output, sdio1_data_out[0]- (8-bit Data bus) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_71_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[19]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[19]- (GPIO bank 2) 1= c
                # n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig
                # al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_n_ss_out[2]- (SPI Master Selects) 5
                #  ttc0, Output, ttc0_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial output) 7= Not Used
                # PSU_IOU_SLCR_MIO_PIN_71_L3_SEL                                                  0

                # Configures MIO Pin 71 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF18011C, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF18011C 0x000000FE 0x00000002
                # Register : MIO_PIN_72 @ 0XFF180120</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Input, gem3_rgmii_rxd[1]- (RX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_72_L0_SEL                                                  1

                # Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_data[4]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_
                # ata[4]- (ULPI data bus)
                # PSU_IOU_SLCR_MIO_PIN_72_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[5]- (8-bit Data bus) = sd0, Output, sdio0_data_out[5]- (8
                # bit Data bus) 2= sd1, Input, sd1_data_in[1]- (8-bit Data bus) = sd1, Output, sdio1_data_out[1]- (8-bit Data bus) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_72_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[20]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[20]- (GPIO bank 2) 1= c
                # n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig
                # al) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi1, Output, spi1_n_ss_out[1]- (SPI Master Selects) 5= N
                # t Used 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= Not Used
                # PSU_IOU_SLCR_MIO_PIN_72_L3_SEL                                                  0

                # Configures MIO Pin 72 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180120, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180120 0x000000FE 0x00000002
                # Register : MIO_PIN_73 @ 0XFF180124</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Input, gem3_rgmii_rxd[2]- (RX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_73_L0_SEL                                                  1

                # Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_data[5]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_
                # ata[5]- (ULPI data bus)
                # PSU_IOU_SLCR_MIO_PIN_73_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[6]- (8-bit Data bus) = sd0, Output, sdio0_data_out[6]- (8
                # bit Data bus) 2= sd1, Input, sd1_data_in[2]- (8-bit Data bus) = sd1, Output, sdio1_data_out[2]- (8-bit Data bus) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_73_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[21]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[21]- (GPIO bank 2) 1= c
                # n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign
                # l) 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi1, Input, spi1_n_ss_in- (SPI Master Selects) 4= spi1
                #  Output, spi1_n_ss_out[0]- (SPI Master Selects) 5= Not Used 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7= Not Used
                # PSU_IOU_SLCR_MIO_PIN_73_L3_SEL                                                  0

                # Configures MIO Pin 73 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180124, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180124 0x000000FE 0x00000002
                # Register : MIO_PIN_74 @ 0XFF180128</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Input, gem3_rgmii_rxd[3]- (RX RGMII data)
                # PSU_IOU_SLCR_MIO_PIN_74_L0_SEL                                                  1

                # Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_data[6]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_
                # ata[6]- (ULPI data bus)
                # PSU_IOU_SLCR_MIO_PIN_74_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[7]- (8-bit Data bus) = sd0, Output, sdio0_data_out[7]- (8
                # bit Data bus) 2= sd1, Input, sd1_data_in[3]- (8-bit Data bus) = sd1, Output, sdio1_data_out[3]- (8-bit Data bus) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_74_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[22]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[22]- (GPIO bank 2) 1= c
                # n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign
                # l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_mi- (MISO signal) 4= spi1, Output, spi1_
                # o- (MISO signal) 5= Not Used 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= Not Used
                # PSU_IOU_SLCR_MIO_PIN_74_L3_SEL                                                  0

                # Configures MIO Pin 74 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180128, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF180128 0x000000FE 0x00000002
                # Register : MIO_PIN_75 @ 0XFF18012C</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Input, gem3_rgmii_rx_ctl- (RX RGMII control )
                # PSU_IOU_SLCR_MIO_PIN_75_L0_SEL                                                  1

                # Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_data[7]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_
                # ata[7]- (ULPI data bus)
                # PSU_IOU_SLCR_MIO_PIN_75_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Output, sdio0_bus_pow- (SD card bus power) 2= sd1, Input, sd1_cmd_in- (Comma
                # d Indicator) = sd1, Output, sdio1_cmd_out- (Command Indicator) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_75_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[23]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[23]- (GPIO bank 2) 1= c
                # n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig
                # al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_mo- (MOSI signal) 4= spi1, Input, s
                # i1_si- (MOSI signal) 5= Not Used 6= ua0, Output, ua0_txd- (UART transmitter serial output) 7= Not Used
                # PSU_IOU_SLCR_MIO_PIN_75_L3_SEL                                                  0

                # Configures MIO Pin 75 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF18012C, 0x000000FEU ,0x00000002U)  */
    mask_write 0XFF18012C 0x000000FE 0x00000002
                # Register : MIO_PIN_76 @ 0XFF180130</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_76_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_76_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sdio0_wp- (SD card write protect from connector) 2= sd1, Output, sdio
                # _clk_out- (SDSDIO clock) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_76_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[24]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[24]- (GPIO bank 2) 1= c
                # n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig
                # al) 3= mdio0, Output, gem0_mdc- (MDIO Clock) 4= mdio1, Output, gem1_mdc- (MDIO Clock) 5= mdio2, Output, gem2_mdc- (MDIO Clock
                #  6= mdio3, Output, gem3_mdc- (MDIO Clock) 7= Not Used
                # PSU_IOU_SLCR_MIO_PIN_76_L3_SEL                                                  6

                # Configures MIO Pin 76 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180130, 0x000000FEU ,0x000000C0U)  */
    mask_write 0XFF180130 0x000000FE 0x000000C0
                # Register : MIO_PIN_77 @ 0XFF180134</p>

                # Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_77_L0_SEL                                                  0

                # Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used
                # PSU_IOU_SLCR_MIO_PIN_77_L1_SEL                                                  0

                # Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= sd1, Input, sdio1_cd_n- (SD card detect from connector) 3= Not Used
                # PSU_IOU_SLCR_MIO_PIN_77_L2_SEL                                                  0

                # Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[25]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[25]- (GPIO bank 2) 1= c
                # n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign
                # l) 3= mdio0, Input, gem0_mdio_in- (MDIO Data) 3= mdio0, Output, gem0_mdio_out- (MDIO Data) 4= mdio1, Input, gem1_mdio_in- (MD
                # O Data) 4= mdio1, Output, gem1_mdio_out- (MDIO Data) 5= mdio2, Input, gem2_mdio_in- (MDIO Data) 5= mdio2, Output, gem2_mdio_o
                # t- (MDIO Data) 6= mdio3, Input, gem3_mdio_in- (MDIO Data) 6= mdio3, Output, gem3_mdio_out- (MDIO Data) 7= Not Used
                # PSU_IOU_SLCR_MIO_PIN_77_L3_SEL                                                  6

                # Configures MIO Pin 77 peripheral interface mapping
                #(OFFSET, MASK, VALUE)      (0XFF180134, 0x000000FEU ,0x000000C0U)  */
    mask_write 0XFF180134 0x000000FE 0x000000C0
                # Register : MIO_MST_TRI0 @ 0XFF180204</p>

                # Master Tri-state Enable for pin 0, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_00_TRI                                            0

                # Master Tri-state Enable for pin 1, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_01_TRI                                            0

                # Master Tri-state Enable for pin 2, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_02_TRI                                            0

                # Master Tri-state Enable for pin 3, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_03_TRI                                            0

                # Master Tri-state Enable for pin 4, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_04_TRI                                            0

                # Master Tri-state Enable for pin 5, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_05_TRI                                            0

                # Master Tri-state Enable for pin 6, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_06_TRI                                            0

                # Master Tri-state Enable for pin 7, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_07_TRI                                            0

                # Master Tri-state Enable for pin 8, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_08_TRI                                            0

                # Master Tri-state Enable for pin 9, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_09_TRI                                            0

                # Master Tri-state Enable for pin 10, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_10_TRI                                            0

                # Master Tri-state Enable for pin 11, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_11_TRI                                            0

                # Master Tri-state Enable for pin 12, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_12_TRI                                            0

                # Master Tri-state Enable for pin 13, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_13_TRI                                            0

                # Master Tri-state Enable for pin 14, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_14_TRI                                            0

                # Master Tri-state Enable for pin 15, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_15_TRI                                            0

                # Master Tri-state Enable for pin 16, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_16_TRI                                            0

                # Master Tri-state Enable for pin 17, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_17_TRI                                            0

                # Master Tri-state Enable for pin 18, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_18_TRI                                            1

                # Master Tri-state Enable for pin 19, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_19_TRI                                            0

                # Master Tri-state Enable for pin 20, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_20_TRI                                            0

                # Master Tri-state Enable for pin 21, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_21_TRI                                            1

                # Master Tri-state Enable for pin 22, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_22_TRI                                            0

                # Master Tri-state Enable for pin 23, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_23_TRI                                            0

                # Master Tri-state Enable for pin 24, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_24_TRI                                            0

                # Master Tri-state Enable for pin 25, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_25_TRI                                            1

                # Master Tri-state Enable for pin 26, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_26_TRI                                            1

                # Master Tri-state Enable for pin 27, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_27_TRI                                            0

                # Master Tri-state Enable for pin 28, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_28_TRI                                            0

                # Master Tri-state Enable for pin 29, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_29_TRI                                            0

                # Master Tri-state Enable for pin 30, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_30_TRI                                            0

                # Master Tri-state Enable for pin 31, active high
                # PSU_IOU_SLCR_MIO_MST_TRI0_PIN_31_TRI                                            0

                # MIO pin Tri-state Enables, 31:0
                #(OFFSET, MASK, VALUE)      (0XFF180204, 0xFFFFFFFFU ,0x06240000U)  */
    mask_write 0XFF180204 0xFFFFFFFF 0x06240000
                # Register : MIO_MST_TRI1 @ 0XFF180208</p>

                # Master Tri-state Enable for pin 32, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_32_TRI                                            0

                # Master Tri-state Enable for pin 33, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_33_TRI                                            0

                # Master Tri-state Enable for pin 34, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_34_TRI                                            0

                # Master Tri-state Enable for pin 35, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_35_TRI                                            0

                # Master Tri-state Enable for pin 36, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_36_TRI                                            0

                # Master Tri-state Enable for pin 37, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_37_TRI                                            0

                # Master Tri-state Enable for pin 38, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_38_TRI                                            0

                # Master Tri-state Enable for pin 39, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_39_TRI                                            0

                # Master Tri-state Enable for pin 40, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_40_TRI                                            0

                # Master Tri-state Enable for pin 41, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_41_TRI                                            0

                # Master Tri-state Enable for pin 42, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_42_TRI                                            0

                # Master Tri-state Enable for pin 43, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_43_TRI                                            0

                # Master Tri-state Enable for pin 44, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_44_TRI                                            1

                # Master Tri-state Enable for pin 45, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_45_TRI                                            1

                # Master Tri-state Enable for pin 46, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_46_TRI                                            0

                # Master Tri-state Enable for pin 47, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_47_TRI                                            0

                # Master Tri-state Enable for pin 48, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_48_TRI                                            0

                # Master Tri-state Enable for pin 49, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_49_TRI                                            0

                # Master Tri-state Enable for pin 50, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_50_TRI                                            0

                # Master Tri-state Enable for pin 51, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_51_TRI                                            0

                # Master Tri-state Enable for pin 52, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_52_TRI                                            1

                # Master Tri-state Enable for pin 53, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_53_TRI                                            1

                # Master Tri-state Enable for pin 54, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_54_TRI                                            0

                # Master Tri-state Enable for pin 55, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_55_TRI                                            1

                # Master Tri-state Enable for pin 56, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_56_TRI                                            0

                # Master Tri-state Enable for pin 57, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_57_TRI                                            0

                # Master Tri-state Enable for pin 58, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_58_TRI                                            0

                # Master Tri-state Enable for pin 59, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_59_TRI                                            0

                # Master Tri-state Enable for pin 60, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_60_TRI                                            0

                # Master Tri-state Enable for pin 61, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_61_TRI                                            0

                # Master Tri-state Enable for pin 62, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_62_TRI                                            0

                # Master Tri-state Enable for pin 63, active high
                # PSU_IOU_SLCR_MIO_MST_TRI1_PIN_63_TRI                                            0

                # MIO pin Tri-state Enables, 63:32
                #(OFFSET, MASK, VALUE)      (0XFF180208, 0xFFFFFFFFU ,0x00B03000U)  */
    mask_write 0XFF180208 0xFFFFFFFF 0x00B03000
                # Register : MIO_MST_TRI2 @ 0XFF18020C</p>

                # Master Tri-state Enable for pin 64, active high
                # PSU_IOU_SLCR_MIO_MST_TRI2_PIN_64_TRI                                            0

                # Master Tri-state Enable for pin 65, active high
                # PSU_IOU_SLCR_MIO_MST_TRI2_PIN_65_TRI                                            0

                # Master Tri-state Enable for pin 66, active high
                # PSU_IOU_SLCR_MIO_MST_TRI2_PIN_66_TRI                                            0

                # Master Tri-state Enable for pin 67, active high
                # PSU_IOU_SLCR_MIO_MST_TRI2_PIN_67_TRI                                            0

                # Master Tri-state Enable for pin 68, active high
                # PSU_IOU_SLCR_MIO_MST_TRI2_PIN_68_TRI                                            0

                # Master Tri-state Enable for pin 69, active high
                # PSU_IOU_SLCR_MIO_MST_TRI2_PIN_69_TRI                                            0

                # Master Tri-state Enable for pin 70, active high
                # PSU_IOU_SLCR_MIO_MST_TRI2_PIN_70_TRI                                            1

                # Master Tri-state Enable for pin 71, active high
                # PSU_IOU_SLCR_MIO_MST_TRI2_PIN_71_TRI                                            1

                # Master Tri-state Enable for pin 72, active high
                # PSU_IOU_SLCR_MIO_MST_TRI2_PIN_72_TRI                                            1

                # Master Tri-state Enable for pin 73, active high
                # PSU_IOU_SLCR_MIO_MST_TRI2_PIN_73_TRI                                            1

                # Master Tri-state Enable for pin 74, active high
                # PSU_IOU_SLCR_MIO_MST_TRI2_PIN_74_TRI                                            1

                # Master Tri-state Enable for pin 75, active high
                # PSU_IOU_SLCR_MIO_MST_TRI2_PIN_75_TRI                                            1

                # Master Tri-state Enable for pin 76, active high
                # PSU_IOU_SLCR_MIO_MST_TRI2_PIN_76_TRI                                            0

                # Master Tri-state Enable for pin 77, active high
                # PSU_IOU_SLCR_MIO_MST_TRI2_PIN_77_TRI                                            0

                # MIO pin Tri-state Enables, 77:64
                #(OFFSET, MASK, VALUE)      (0XFF18020C, 0x00003FFFU ,0x00000FC0U)  */
    mask_write 0XFF18020C 0x00003FFF 0x00000FC0
                # Register : bank0_ctrl0 @ 0XFF180138</p>

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_0                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_1                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_2                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_3                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_4                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_5                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_6                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_7                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_8                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_9                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_10                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_11                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_12                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_13                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_14                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_15                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_16                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_17                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_18                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_19                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_20                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_21                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_22                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_23                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_24                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_25                                          1

                # Drive0 control to MIO Bank 0 - control MIO[25:0]
                #(OFFSET, MASK, VALUE)      (0XFF180138, 0x03FFFFFFU ,0x03FFFFFFU)  */
    mask_write 0XFF180138 0x03FFFFFF 0x03FFFFFF
                # Register : bank0_ctrl1 @ 0XFF18013C</p>

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_0                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_1                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_2                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_3                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_4                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_5                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_6                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_7                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_8                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_9                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_10                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_11                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_12                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_13                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_14                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_15                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_16                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_17                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_18                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_19                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_20                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_21                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_22                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_23                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_24                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_25                                          1

                # Drive1 control to MIO Bank 0 - control MIO[25:0]
                #(OFFSET, MASK, VALUE)      (0XFF18013C, 0x03FFFFFFU ,0x03FFFFFFU)  */
    mask_write 0XFF18013C 0x03FFFFFF 0x03FFFFFF
                # Register : bank0_ctrl3 @ 0XFF180140</p>

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_0                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_1                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_2                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_3                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_4                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_5                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_6                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_7                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_8                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_9                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_10                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_11                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_12                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_13                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_14                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_15                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_16                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_17                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_18                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_19                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_20                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_21                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_22                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_23                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_24                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_25                                  0

                # Selects either Schmitt or CMOS input for MIO Bank 0 - control MIO[25:0]
                #(OFFSET, MASK, VALUE)      (0XFF180140, 0x03FFFFFFU ,0x00000000U)  */
    mask_write 0XFF180140 0x03FFFFFF 0x00000000
                # Register : bank0_ctrl4 @ 0XFF180144</p>

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_0                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_1                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_2                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_3                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_4                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_5                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_6                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_7                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_8                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_9                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_10                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_11                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_12                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_13                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_14                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_15                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_16                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_17                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_18                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_19                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_20                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_21                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_22                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_23                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_24                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_25                                 1

                # When mio_bank0_pull_enable is set, this selects pull up or pull down for MIO Bank 0 - control MIO[25:0]
                #(OFFSET, MASK, VALUE)      (0XFF180144, 0x03FFFFFFU ,0x03FFFFFFU)  */
    mask_write 0XFF180144 0x03FFFFFF 0x03FFFFFF
                # Register : bank0_ctrl5 @ 0XFF180148</p>

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_0                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_1                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_2                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_3                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_4                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_5                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_6                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_7                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_8                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_9                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_10                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_11                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_12                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_13                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_14                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_15                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_16                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_17                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_18                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_19                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_20                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_21                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_22                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_23                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_24                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_25                                     1

                # When set, this enables mio_bank0_pullupdown to selects pull up or pull down for MIO Bank 0 - control MIO[25:0]
                #(OFFSET, MASK, VALUE)      (0XFF180148, 0x03FFFFFFU ,0x03FFFFFFU)  */
    mask_write 0XFF180148 0x03FFFFFF 0x03FFFFFF
                # Register : bank0_ctrl6 @ 0XFF18014C</p>

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_0                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_1                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_2                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_3                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_4                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_5                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_6                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_7                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_8                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_9                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_10                                0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_11                                0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_12                                0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_13                                0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_14                                0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_15                                0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_16                                0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_17                                0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_18                                0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_19                                0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_20                                0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_21                                0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_22                                0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_23                                0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_24                                0

                # Each bit applies to a single IO. Bit 0 for MIO[0].
                # PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_25                                0

                # Slew rate control to MIO Bank 0 - control MIO[25:0]
                #(OFFSET, MASK, VALUE)      (0XFF18014C, 0x03FFFFFFU ,0x00000000U)  */
    mask_write 0XFF18014C 0x03FFFFFF 0x00000000
                # Register : bank1_ctrl0 @ 0XFF180154</p>

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_0                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_1                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_2                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_3                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_4                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_5                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_6                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_7                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_8                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_9                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_10                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_11                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_12                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_13                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_14                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_15                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_16                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_17                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_18                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_19                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_20                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_21                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_22                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_23                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_24                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_25                                          1

                # Drive0 control to MIO Bank 1 - control MIO[51:26]
                #(OFFSET, MASK, VALUE)      (0XFF180154, 0x03FFFFFFU ,0x03FFFFFFU)  */
    mask_write 0XFF180154 0x03FFFFFF 0x03FFFFFF
                # Register : bank1_ctrl1 @ 0XFF180158</p>

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_0                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_1                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_2                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_3                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_4                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_5                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_6                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_7                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_8                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_9                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_10                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_11                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_12                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_13                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_14                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_15                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_16                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_17                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_18                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_19                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_20                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_21                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_22                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_23                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_24                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_25                                          1

                # Drive1 control to MIO Bank 1 - control MIO[51:26]
                #(OFFSET, MASK, VALUE)      (0XFF180158, 0x03FFFFFFU ,0x03FFFFFFU)  */
    mask_write 0XFF180158 0x03FFFFFF 0x03FFFFFF
                # Register : bank1_ctrl3 @ 0XFF18015C</p>

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_0                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_1                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_2                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_3                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_4                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_5                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_6                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_7                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_8                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_9                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_10                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_11                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_12                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_13                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_14                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_15                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_16                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_17                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_18                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_19                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_20                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_21                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_22                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_23                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_24                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_25                                  0

                # Selects either Schmitt or CMOS input for MIO Bank 1 - control MIO[51:26]
                #(OFFSET, MASK, VALUE)      (0XFF18015C, 0x03FFFFFFU ,0x00000000U)  */
    mask_write 0XFF18015C 0x03FFFFFF 0x00000000
                # Register : bank1_ctrl4 @ 0XFF180160</p>

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_0                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_1                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_2                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_3                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_4                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_5                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_6                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_7                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_8                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_9                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_10                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_11                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_12                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_13                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_14                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_15                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_16                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_17                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_18                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_19                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_20                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_21                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_22                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_23                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_24                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_25                                 1

                # When mio_bank1_pull_enable is set, this selects pull up or pull down for MIO Bank 1 - control MIO[51:26]
                #(OFFSET, MASK, VALUE)      (0XFF180160, 0x03FFFFFFU ,0x03FFFFFFU)  */
    mask_write 0XFF180160 0x03FFFFFF 0x03FFFFFF
                # Register : bank1_ctrl5 @ 0XFF180164</p>

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_0                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_1                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_2                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_3                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_4                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_5                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_6                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_7                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_8                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_9                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_10                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_11                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_12                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_13                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_14                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_15                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_16                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_17                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_18                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_19                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_20                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_21                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_22                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_23                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_24                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_25                                     1

                # When set, this enables mio_bank1_pullupdown to selects pull up or pull down for MIO Bank 1 - control MIO[51:26]
                #(OFFSET, MASK, VALUE)      (0XFF180164, 0x03FFFFFFU ,0x03FFFFFFU)  */
    mask_write 0XFF180164 0x03FFFFFF 0x03FFFFFF
                # Register : bank1_ctrl6 @ 0XFF180168</p>

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_0                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_1                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_2                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_3                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_4                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_5                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_6                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_7                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_8                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_9                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_10                                0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_11                                0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_12                                0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_13                                0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_14                                0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_15                                0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_16                                0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_17                                0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_18                                0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_19                                0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_20                                0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_21                                0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_22                                0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_23                                0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_24                                0

                # Each bit applies to a single IO. Bit 0 for MIO[26].
                # PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_25                                0

                # Slew rate control to MIO Bank 1 - control MIO[51:26]
                #(OFFSET, MASK, VALUE)      (0XFF180168, 0x03FFFFFFU ,0x00000000U)  */
    mask_write 0XFF180168 0x03FFFFFF 0x00000000
                # Register : bank2_ctrl0 @ 0XFF180170</p>

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_0                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_1                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_2                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_3                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_4                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_5                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_6                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_7                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_8                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_9                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_10                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_11                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_12                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_13                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_14                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_15                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_16                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_17                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_18                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_19                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_20                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_21                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_22                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_23                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_24                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_25                                          1

                # Drive0 control to MIO Bank 2 - control MIO[77:52]
                #(OFFSET, MASK, VALUE)      (0XFF180170, 0x03FFFFFFU ,0x03FFFFFFU)  */
    mask_write 0XFF180170 0x03FFFFFF 0x03FFFFFF
                # Register : bank2_ctrl1 @ 0XFF180174</p>

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_0                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_1                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_2                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_3                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_4                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_5                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_6                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_7                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_8                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_9                                           1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_10                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_11                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_12                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_13                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_14                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_15                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_16                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_17                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_18                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_19                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_20                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_21                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_22                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_23                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_24                                          1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_25                                          1

                # Drive1 control to MIO Bank 2 - control MIO[77:52]
                #(OFFSET, MASK, VALUE)      (0XFF180174, 0x03FFFFFFU ,0x03FFFFFFU)  */
    mask_write 0XFF180174 0x03FFFFFF 0x03FFFFFF
                # Register : bank2_ctrl3 @ 0XFF180178</p>

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_0                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_1                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_2                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_3                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_4                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_5                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_6                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_7                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_8                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_9                                   0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_10                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_11                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_12                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_13                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_14                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_15                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_16                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_17                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_18                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_19                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_20                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_21                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_22                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_23                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_24                                  0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_25                                  0

                # Selects either Schmitt or CMOS input for MIO Bank 2 - control MIO[77:52]
                #(OFFSET, MASK, VALUE)      (0XFF180178, 0x03FFFFFFU ,0x00000000U)  */
    mask_write 0XFF180178 0x03FFFFFF 0x00000000
                # Register : bank2_ctrl4 @ 0XFF18017C</p>

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_0                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_1                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_2                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_3                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_4                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_5                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_6                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_7                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_8                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_9                                  1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_10                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_11                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_12                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_13                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_14                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_15                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_16                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_17                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_18                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_19                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_20                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_21                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_22                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_23                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_24                                 1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_25                                 1

                # When mio_bank2_pull_enable is set, this selects pull up or pull down for MIO Bank 2 - control MIO[77:52]
                #(OFFSET, MASK, VALUE)      (0XFF18017C, 0x03FFFFFFU ,0x03FFFFFFU)  */
    mask_write 0XFF18017C 0x03FFFFFF 0x03FFFFFF
                # Register : bank2_ctrl5 @ 0XFF180180</p>

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_0                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_1                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_2                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_3                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_4                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_5                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_6                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_7                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_8                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_9                                      1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_10                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_11                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_12                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_13                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_14                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_15                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_16                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_17                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_18                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_19                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_20                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_21                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_22                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_23                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_24                                     1

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_25                                     1

                # When set, this enables mio_bank2_pullupdown to selects pull up or pull down for MIO Bank 2 - control MIO[77:52]
                #(OFFSET, MASK, VALUE)      (0XFF180180, 0x03FFFFFFU ,0x03FFFFFFU)  */
    mask_write 0XFF180180 0x03FFFFFF 0x03FFFFFF
                # Register : bank2_ctrl6 @ 0XFF180184</p>

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_0                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_1                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_2                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_3                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_4                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_5                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_6                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_7                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_8                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_9                                 0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_10                                0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_11                                0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_12                                0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_13                                0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_14                                0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_15                                0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_16                                0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_17                                0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_18                                0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_19                                0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_20                                0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_21                                0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_22                                0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_23                                0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_24                                0

                # Each bit applies to a single IO. Bit 0 for MIO[52].
                # PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_25                                0

                # Slew rate control to MIO Bank 2 - control MIO[77:52]
                #(OFFSET, MASK, VALUE)      (0XFF180184, 0x03FFFFFFU ,0x00000000U)  */
    mask_write 0XFF180184 0x03FFFFFF 0x00000000
                # : LOOPBACK
                # Register : MIO_LOOPBACK @ 0XFF180200</p>

                # I2C Loopback Control. 0 = Connect I2C inputs according to MIO mapping. 1 = Loop I2C 0 outputs to I2C 1 inputs, and I2C 1 outp
                # ts to I2C 0 inputs.
                # PSU_IOU_SLCR_MIO_LOOPBACK_I2C0_LOOP_I2C1                                        0

                # CAN Loopback Control. 0 = Connect CAN inputs according to MIO mapping. 1 = Loop CAN 0 Tx to CAN 1 Rx, and CAN 1 Tx to CAN 0 R
                # .
                # PSU_IOU_SLCR_MIO_LOOPBACK_CAN0_LOOP_CAN1                                        0

                # UART Loopback Control. 0 = Connect UART inputs according to MIO mapping. 1 = Loop UART 0 outputs to UART 1 inputs, and UART 1
                # outputs to UART 0 inputs. RXD/TXD cross-connected. RTS/CTS cross-connected. DSR, DTR, DCD and RI not used.
                # PSU_IOU_SLCR_MIO_LOOPBACK_UA0_LOOP_UA1                                          0

                # SPI Loopback Control. 0 = Connect SPI inputs according to MIO mapping. 1 = Loop SPI 0 outputs to SPI 1 inputs, and SPI 1 outp
                # ts to SPI 0 inputs. The other SPI core will appear on the LS Slave Select.
                # PSU_IOU_SLCR_MIO_LOOPBACK_SPI0_LOOP_SPI1                                        0

                # Loopback function within MIO
                #(OFFSET, MASK, VALUE)      (0XFF180200, 0x0000000FU ,0x00000000U)  */
    mask_write 0XFF180200 0x0000000F 0x00000000
}

set psu_peripherals_init_data {
                # : RESET BLOCKS
                # : ENET
                # Register : RST_LPD_IOU0 @ 0XFF5E0230</p>

                # GEM 3 reset
                # PSU_CRL_APB_RST_LPD_IOU0_GEM3_RESET                                             0

                # Software controlled reset for the GEMs
                #(OFFSET, MASK, VALUE)      (0XFF5E0230, 0x00000008U ,0x00000000U)  */
    mask_write 0XFF5E0230 0x00000008 0x00000000
                # : QSPI
                # Register : RST_LPD_IOU2 @ 0XFF5E0238</p>

                # Block level reset
                # PSU_CRL_APB_RST_LPD_IOU2_QSPI_RESET                                             0

                # Software control register for the IOU block. Each bit will cause a singlerperipheral or part of the peripheral to be reset.
                #(OFFSET, MASK, VALUE)      (0XFF5E0238, 0x00000001U ,0x00000000U)  */
    mask_write 0XFF5E0238 0x00000001 0x00000000
                # : NAND
                # : USB
                # Register : RST_LPD_TOP @ 0XFF5E023C</p>

                # USB 0 reset for control registers
                # PSU_CRL_APB_RST_LPD_TOP_USB0_APB_RESET                                          0

                # USB 0 sleep circuit reset
                # PSU_CRL_APB_RST_LPD_TOP_USB0_HIBERRESET                                         0

                # USB 0 reset
                # PSU_CRL_APB_RST_LPD_TOP_USB0_CORERESET                                          0

                # Software control register for the LPD block.
                #(OFFSET, MASK, VALUE)      (0XFF5E023C, 0x00000540U ,0x00000000U)  */
    mask_write 0XFF5E023C 0x00000540 0x00000000
                # : FPD RESET
                # Register : RST_FPD_TOP @ 0XFD1A0100</p>

                # PCIE config reset
                # PSU_CRF_APB_RST_FPD_TOP_PCIE_CFG_RESET                                          0

                # PCIE control block level reset
                # PSU_CRF_APB_RST_FPD_TOP_PCIE_CTRL_RESET                                         0

                # PCIE bridge block level reset (AXI interface)
                # PSU_CRF_APB_RST_FPD_TOP_PCIE_BRIDGE_RESET                                       0

                # Display Port block level reset (includes DPDMA)
                # PSU_CRF_APB_RST_FPD_TOP_DP_RESET                                                0

                # FPD WDT reset
                # PSU_CRF_APB_RST_FPD_TOP_SWDT_RESET                                              0

                # GDMA block level reset
                # PSU_CRF_APB_RST_FPD_TOP_GDMA_RESET                                              0

                # Pixel Processor (submodule of GPU) block level reset
                # PSU_CRF_APB_RST_FPD_TOP_GPU_PP0_RESET                                           0

                # Pixel Processor (submodule of GPU) block level reset
                # PSU_CRF_APB_RST_FPD_TOP_GPU_PP1_RESET                                           0

                # GPU block level reset
                # PSU_CRF_APB_RST_FPD_TOP_GPU_RESET                                               0

                # GT block level reset
                # PSU_CRF_APB_RST_FPD_TOP_GT_RESET                                                0

                # Sata block level reset
                # PSU_CRF_APB_RST_FPD_TOP_SATA_RESET                                              0

                # FPD Block level software controlled reset
                #(OFFSET, MASK, VALUE)      (0XFD1A0100, 0x000F807EU ,0x00000000U)  */
    mask_write 0XFD1A0100 0x000F807E 0x00000000
                # : SD
                # Register : RST_LPD_IOU2 @ 0XFF5E0238</p>

                # Block level reset
                # PSU_CRL_APB_RST_LPD_IOU2_SDIO1_RESET                                            0

                # Software control register for the IOU block. Each bit will cause a singlerperipheral or part of the peripheral to be reset.
                #(OFFSET, MASK, VALUE)      (0XFF5E0238, 0x00000040U ,0x00000000U)  */
    mask_write 0XFF5E0238 0x00000040 0x00000000
                # Register : CTRL_REG_SD @ 0XFF180310</p>

                # SD or eMMC selection on SDIO1 0: SD enabled 1: eMMC enabled
                # PSU_IOU_SLCR_CTRL_REG_SD_SD1_EMMC_SEL                                           0

                # SD eMMC selection
                #(OFFSET, MASK, VALUE)      (0XFF180310, 0x00008000U ,0x00000000U)  */
    mask_write 0XFF180310 0x00008000 0x00000000
                # Register : SD_CONFIG_REG2 @ 0XFF180320</p>

                # Should be set based on the final product usage 00 - Removable SCard Slot 01 - Embedded Slot for One Device 10 - Shared Bus Sl
                # t 11 - Reserved
                # PSU_IOU_SLCR_SD_CONFIG_REG2_SD1_SLOTTYPE                                        0

                # 1.8V Support 1: 1.8V supported 0: 1.8V not supported support
                # PSU_IOU_SLCR_SD_CONFIG_REG2_SD1_1P8V                                            0

                # 3.0V Support 1: 3.0V supported 0: 3.0V not supported support
                # PSU_IOU_SLCR_SD_CONFIG_REG2_SD1_3P0V                                            0

                # 3.3V Support 1: 3.3V supported 0: 3.3V not supported support
                # PSU_IOU_SLCR_SD_CONFIG_REG2_SD1_3P3V                                            1

                # SD Config Register 2
                #(OFFSET, MASK, VALUE)      (0XFF180320, 0x33800000U ,0x00800000U)  */
    mask_write 0XFF180320 0x33800000 0x00800000
                # : SD1 BASE CLOCK
                # Register : SD_CONFIG_REG1 @ 0XFF18031C</p>

                # Base Clock Frequency for SD Clock. This is the frequency of the xin_clk.
                # PSU_IOU_SLCR_SD_CONFIG_REG1_SD1_BASECLK                                         0xc7

                # SD Config Register 1
                #(OFFSET, MASK, VALUE)      (0XFF18031C, 0x7F800000U ,0x63800000U)  */
    mask_write 0XFF18031C 0x7F800000 0x63800000
                # : CAN
                # Register : RST_LPD_IOU2 @ 0XFF5E0238</p>

                # Block level reset
                # PSU_CRL_APB_RST_LPD_IOU2_CAN1_RESET                                             0

                # Software control register for the IOU block. Each bit will cause a singlerperipheral or part of the peripheral to be reset.
                #(OFFSET, MASK, VALUE)      (0XFF5E0238, 0x00000100U ,0x00000000U)  */
    mask_write 0XFF5E0238 0x00000100 0x00000000
                # : I2C
                # Register : RST_LPD_IOU2 @ 0XFF5E0238</p>

                # Block level reset
                # PSU_CRL_APB_RST_LPD_IOU2_I2C0_RESET                                             0

                # Block level reset
                # PSU_CRL_APB_RST_LPD_IOU2_I2C1_RESET                                             0

                # Software control register for the IOU block. Each bit will cause a singlerperipheral or part of the peripheral to be reset.
                #(OFFSET, MASK, VALUE)      (0XFF5E0238, 0x00000600U ,0x00000000U)  */
    mask_write 0XFF5E0238 0x00000600 0x00000000
                # : SWDT
                # Register : RST_LPD_IOU2 @ 0XFF5E0238</p>

                # Block level reset
                # PSU_CRL_APB_RST_LPD_IOU2_SWDT_RESET                                             0

                # Software control register for the IOU block. Each bit will cause a singlerperipheral or part of the peripheral to be reset.
                #(OFFSET, MASK, VALUE)      (0XFF5E0238, 0x00008000U ,0x00000000U)  */
    mask_write 0XFF5E0238 0x00008000 0x00000000
                # : SPI
                # : TTC
                # Register : RST_LPD_IOU2 @ 0XFF5E0238</p>

                # Block level reset
                # PSU_CRL_APB_RST_LPD_IOU2_TTC0_RESET                                             0

                # Block level reset
                # PSU_CRL_APB_RST_LPD_IOU2_TTC1_RESET                                             0

                # Block level reset
                # PSU_CRL_APB_RST_LPD_IOU2_TTC2_RESET                                             0

                # Block level reset
                # PSU_CRL_APB_RST_LPD_IOU2_TTC3_RESET                                             0

                # Software control register for the IOU block. Each bit will cause a singlerperipheral or part of the peripheral to be reset.
                #(OFFSET, MASK, VALUE)      (0XFF5E0238, 0x00007800U ,0x00000000U)  */
    mask_write 0XFF5E0238 0x00007800 0x00000000
                # : UART
                # Register : RST_LPD_IOU2 @ 0XFF5E0238</p>

                # Block level reset
                # PSU_CRL_APB_RST_LPD_IOU2_UART0_RESET                                            0

                # Block level reset
                # PSU_CRL_APB_RST_LPD_IOU2_UART1_RESET                                            0

                # Software control register for the IOU block. Each bit will cause a singlerperipheral or part of the peripheral to be reset.
                #(OFFSET, MASK, VALUE)      (0XFF5E0238, 0x00000006U ,0x00000000U)  */
    mask_write 0XFF5E0238 0x00000006 0x00000000
                # : UART BAUD RATE
                # Register : Baud_rate_divider_reg0 @ 0XFF000034</p>

                # Baud rate divider value: 0 - 3: ignored 4 - 255: Baud rate
                # PSU_UART0_BAUD_RATE_DIVIDER_REG0_BDIV                                           0x5

                # Baud Rate Divider Register
                #(OFFSET, MASK, VALUE)      (0XFF000034, 0x000000FFU ,0x00000005U)  */
    mask_write 0XFF000034 0x000000FF 0x00000005
                # Register : Baud_rate_gen_reg0 @ 0XFF000018</p>

                # Baud Rate Clock Divisor Value: 0: Disables baud_sample 1: Clock divisor bypass (baud_sample = sel_clk) 2 - 65535: baud_sample
                # PSU_UART0_BAUD_RATE_GEN_REG0_CD                                                 0x8f

                # Baud Rate Generator Register.
                #(OFFSET, MASK, VALUE)      (0XFF000018, 0x0000FFFFU ,0x0000008FU)  */
    mask_write 0XFF000018 0x0000FFFF 0x0000008F
                # Register : Control_reg0 @ 0XFF000000</p>

                # Stop transmitter break: 0: no affect 1: stop transmission of the break after a minimum of one character length and transmit a
                # high level during 12 bit periods. It can be set regardless of the value of STTBRK.
                # PSU_UART0_CONTROL_REG0_STPBRK                                                   0x0

                # Start transmitter break: 0: no affect 1: start to transmit a break after the characters currently present in the FIFO and the
                # transmit shift register have been transmitted. It can only be set if STPBRK (Stop transmitter break) is not high.
                # PSU_UART0_CONTROL_REG0_STTBRK                                                   0x0

                # Restart receiver timeout counter: 1: receiver timeout counter is restarted. This bit is self clearing once the restart has co
                # pleted.
                # PSU_UART0_CONTROL_REG0_RSTTO                                                    0x0

                # Transmit disable: 0: enable transmitter 1: disable transmitter
                # PSU_UART0_CONTROL_REG0_TXDIS                                                    0x0

                # Transmit enable: 0: disable transmitter 1: enable transmitter, provided the TXDIS field is set to 0.
                # PSU_UART0_CONTROL_REG0_TXEN                                                     0x1

                # Receive disable: 0: enable 1: disable, regardless of the value of RXEN
                # PSU_UART0_CONTROL_REG0_RXDIS                                                    0x0

                # Receive enable: 0: disable 1: enable When set to one, the receiver logic is enabled, provided the RXDIS field is set to zero.
                # PSU_UART0_CONTROL_REG0_RXEN                                                     0x1

                # Software reset for Tx data path: 0: no affect 1: transmitter logic is reset and all pending transmitter data is discarded Thi
                #  bit is self clearing once the reset has completed.
                # PSU_UART0_CONTROL_REG0_TXRES                                                    0x1

                # Software reset for Rx data path: 0: no affect 1: receiver logic is reset and all pending receiver data is discarded. This bit
                # is self clearing once the reset has completed.
                # PSU_UART0_CONTROL_REG0_RXRES                                                    0x1

                # UART Control Register
                #(OFFSET, MASK, VALUE)      (0XFF000000, 0x000001FFU ,0x00000017U)  */
    mask_write 0XFF000000 0x000001FF 0x00000017
                # Register : mode_reg0 @ 0XFF000004</p>

                # Channel mode: Defines the mode of operation of the UART. 00: normal 01: automatic echo 10: local loopback 11: remote loopback
                # PSU_UART0_MODE_REG0_CHMODE                                                      0x0

                # Number of stop bits: Defines the number of stop bits to detect on receive and to generate on transmit. 00: 1 stop bit 01: 1.5
                # stop bits 10: 2 stop bits 11: reserved
                # PSU_UART0_MODE_REG0_NBSTOP                                                      0x0

                # Parity type select: Defines the expected parity to check on receive and the parity to generate on transmit. 000: even parity 
                # 01: odd parity 010: forced to 0 parity (space) 011: forced to 1 parity (mark) 1xx: no parity
                # PSU_UART0_MODE_REG0_PAR                                                         0x4

                # Character length select: Defines the number of bits in each character. 11: 6 bits 10: 7 bits 0x: 8 bits
                # PSU_UART0_MODE_REG0_CHRL                                                        0x0

                # Clock source select: This field defines whether a pre-scalar of 8 is applied to the baud rate generator input clock. 0: clock
                # source is uart_ref_clk 1: clock source is uart_ref_clk/8
                # PSU_UART0_MODE_REG0_CLKS                                                        0x0

                # UART Mode Register
                #(OFFSET, MASK, VALUE)      (0XFF000004, 0x000003FFU ,0x00000020U)  */
    mask_write 0XFF000004 0x000003FF 0x00000020
                # Register : Baud_rate_divider_reg0 @ 0XFF010034</p>

                # Baud rate divider value: 0 - 3: ignored 4 - 255: Baud rate
                # PSU_UART1_BAUD_RATE_DIVIDER_REG0_BDIV                                           0x5

                # Baud Rate Divider Register
                #(OFFSET, MASK, VALUE)      (0XFF010034, 0x000000FFU ,0x00000005U)  */
    mask_write 0XFF010034 0x000000FF 0x00000005
                # Register : Baud_rate_gen_reg0 @ 0XFF010018</p>

                # Baud Rate Clock Divisor Value: 0: Disables baud_sample 1: Clock divisor bypass (baud_sample = sel_clk) 2 - 65535: baud_sample
                # PSU_UART1_BAUD_RATE_GEN_REG0_CD                                                 0x8f

                # Baud Rate Generator Register.
                #(OFFSET, MASK, VALUE)      (0XFF010018, 0x0000FFFFU ,0x0000008FU)  */
    mask_write 0XFF010018 0x0000FFFF 0x0000008F
                # Register : Control_reg0 @ 0XFF010000</p>

                # Stop transmitter break: 0: no affect 1: stop transmission of the break after a minimum of one character length and transmit a
                # high level during 12 bit periods. It can be set regardless of the value of STTBRK.
                # PSU_UART1_CONTROL_REG0_STPBRK                                                   0x0

                # Start transmitter break: 0: no affect 1: start to transmit a break after the characters currently present in the FIFO and the
                # transmit shift register have been transmitted. It can only be set if STPBRK (Stop transmitter break) is not high.
                # PSU_UART1_CONTROL_REG0_STTBRK                                                   0x0

                # Restart receiver timeout counter: 1: receiver timeout counter is restarted. This bit is self clearing once the restart has co
                # pleted.
                # PSU_UART1_CONTROL_REG0_RSTTO                                                    0x0

                # Transmit disable: 0: enable transmitter 1: disable transmitter
                # PSU_UART1_CONTROL_REG0_TXDIS                                                    0x0

                # Transmit enable: 0: disable transmitter 1: enable transmitter, provided the TXDIS field is set to 0.
                # PSU_UART1_CONTROL_REG0_TXEN                                                     0x1

                # Receive disable: 0: enable 1: disable, regardless of the value of RXEN
                # PSU_UART1_CONTROL_REG0_RXDIS                                                    0x0

                # Receive enable: 0: disable 1: enable When set to one, the receiver logic is enabled, provided the RXDIS field is set to zero.
                # PSU_UART1_CONTROL_REG0_RXEN                                                     0x1

                # Software reset for Tx data path: 0: no affect 1: transmitter logic is reset and all pending transmitter data is discarded Thi
                #  bit is self clearing once the reset has completed.
                # PSU_UART1_CONTROL_REG0_TXRES                                                    0x1

                # Software reset for Rx data path: 0: no affect 1: receiver logic is reset and all pending receiver data is discarded. This bit
                # is self clearing once the reset has completed.
                # PSU_UART1_CONTROL_REG0_RXRES                                                    0x1

                # UART Control Register
                #(OFFSET, MASK, VALUE)      (0XFF010000, 0x000001FFU ,0x00000017U)  */
    mask_write 0XFF010000 0x000001FF 0x00000017
                # Register : mode_reg0 @ 0XFF010004</p>

                # Channel mode: Defines the mode of operation of the UART. 00: normal 01: automatic echo 10: local loopback 11: remote loopback
                # PSU_UART1_MODE_REG0_CHMODE                                                      0x0

                # Number of stop bits: Defines the number of stop bits to detect on receive and to generate on transmit. 00: 1 stop bit 01: 1.5
                # stop bits 10: 2 stop bits 11: reserved
                # PSU_UART1_MODE_REG0_NBSTOP                                                      0x0

                # Parity type select: Defines the expected parity to check on receive and the parity to generate on transmit. 000: even parity 
                # 01: odd parity 010: forced to 0 parity (space) 011: forced to 1 parity (mark) 1xx: no parity
                # PSU_UART1_MODE_REG0_PAR                                                         0x4

                # Character length select: Defines the number of bits in each character. 11: 6 bits 10: 7 bits 0x: 8 bits
                # PSU_UART1_MODE_REG0_CHRL                                                        0x0

                # Clock source select: This field defines whether a pre-scalar of 8 is applied to the baud rate generator input clock. 0: clock
                # source is uart_ref_clk 1: clock source is uart_ref_clk/8
                # PSU_UART1_MODE_REG0_CLKS                                                        0x0

                # UART Mode Register
                #(OFFSET, MASK, VALUE)      (0XFF010004, 0x000003FFU ,0x00000020U)  */
    mask_write 0XFF010004 0x000003FF 0x00000020
                # : GPIO
                # : ADMA TZ
                # Register : slcr_adma @ 0XFF4B0024</p>

                # TrustZone Classification for ADMA
                # PSU_LPD_SLCR_SECURE_SLCR_ADMA_TZ                                                0XFF

                # RPU TrustZone settings
                #(OFFSET, MASK, VALUE)      (0XFF4B0024, 0x000000FFU ,0x000000FFU)  */
    mask_write 0XFF4B0024 0x000000FF 0x000000FF
                # : CSU TAMPERING
                # : CSU TAMPER STATUS
                # Register : tamper_status @ 0XFFCA5000</p>

                # CSU regsiter
                # PSU_CSU_TAMPER_STATUS_TAMPER_0                                                  0

                # External MIO
                # PSU_CSU_TAMPER_STATUS_TAMPER_1                                                  0

                # JTAG toggle detect
                # PSU_CSU_TAMPER_STATUS_TAMPER_2                                                  0

                # PL SEU error
                # PSU_CSU_TAMPER_STATUS_TAMPER_3                                                  0

                # AMS over temperature alarm for LPD
                # PSU_CSU_TAMPER_STATUS_TAMPER_4                                                  0

                # AMS over temperature alarm for APU
                # PSU_CSU_TAMPER_STATUS_TAMPER_5                                                  0

                # AMS voltage alarm for VCCPINT_FPD
                # PSU_CSU_TAMPER_STATUS_TAMPER_6                                                  0

                # AMS voltage alarm for VCCPINT_LPD
                # PSU_CSU_TAMPER_STATUS_TAMPER_7                                                  0

                # AMS voltage alarm for VCCPAUX
                # PSU_CSU_TAMPER_STATUS_TAMPER_8                                                  0

                # AMS voltage alarm for DDRPHY
                # PSU_CSU_TAMPER_STATUS_TAMPER_9                                                  0

                # AMS voltage alarm for PSIO bank 0/1/2
                # PSU_CSU_TAMPER_STATUS_TAMPER_10                                                 0

                # AMS voltage alarm for PSIO bank 3 (dedicated pins)
                # PSU_CSU_TAMPER_STATUS_TAMPER_11                                                 0

                # AMS voltaage alarm for GT
                # PSU_CSU_TAMPER_STATUS_TAMPER_12                                                 0

                # Tamper Response Status
                #(OFFSET, MASK, VALUE)      (0XFFCA5000, 0x00001FFFU ,0x00000000U)  */
    mask_write 0XFFCA5000 0x00001FFF 0x00000000
                # : CSU TAMPER RESPONSE
                # : AFIFM INTERFACE WIDTH
                # : CPU QOS DEFAULT
                # Register : ACE_CTRL @ 0XFD5C0060</p>

                # Set ACE outgoing AWQOS value
                # PSU_APU_ACE_CTRL_AWQOS                                                          0X0

                # Set ACE outgoing ARQOS value
                # PSU_APU_ACE_CTRL_ARQOS                                                          0X0

                # ACE Control Register
                #(OFFSET, MASK, VALUE)      (0XFD5C0060, 0x000F000FU ,0x00000000U)  */
    mask_write 0XFD5C0060 0x000F000F 0x00000000
                # : ENABLES RTC SWITCH TO BATTERY WHEN VCC_PSAUX IS NOT AVAILABLE
                # Register : CONTROL @ 0XFFA60040</p>

                # Enables the RTC. By writing a 0 to this bit, RTC will be powered off and the only module that potentially draws current from 
                # he battery will be BBRAM. The value read through this bit does not necessarily reflect whether RTC is enabled or not. It is e
                # pected that RTC is enabled every time it is being configured. If RTC is not used in the design, FSBL will disable it by writi
                # g a 0 to this bit.
                # PSU_RTC_CONTROL_BATTERY_DISABLE                                                 0X1

                # This register controls various functionalities within the RTC
                #(OFFSET, MASK, VALUE)      (0XFFA60040, 0x80000000U ,0x80000000U)  */
    mask_write 0XFFA60040 0x80000000 0x80000000
}

set psu_post_config_data {
                # : POST_CONFIG
}

set psu_peripherals_powerdwn_data {
                # : POWER DOWN REQUEST INTERRUPT ENABLE
                # : POWER DOWN TRIGGER
}

set psu_serdes_init_data {
                # : SERDES INITIALIZATION
                # : GT REFERENCE CLOCK SOURCE SELECTION
                # Register : PLL_REF_SEL0 @ 0XFD410000</p>

                # PLL0 Reference Selection. 0x0 - 5MHz, 0x1 - 9.6MHz, 0x2 - 10MHz, 0x3 - 12MHz, 0x4 - 13MHz, 0x5 - 19.2MHz, 0x6 - 20MHz, 0x7 - 
                # 4MHz, 0x8 - 26MHz, 0x9 - 27MHz, 0xA - 38.4MHz, 0xB - 40MHz, 0xC - 52MHz, 0xD - 100MHz, 0xE - 108MHz, 0xF - 125MHz, 0x10 - 135
                # Hz, 0x11 - 150 MHz. 0x12 to 0x1F - Reserved
                # PSU_SERDES_PLL_REF_SEL0_PLLREFSEL0                                              0xD

                # PLL0 Reference Selection Register
                #(OFFSET, MASK, VALUE)      (0XFD410000, 0x0000001FU ,0x0000000DU)  */
    mask_write 0XFD410000 0x0000001F 0x0000000D
                # Register : PLL_REF_SEL1 @ 0XFD410004</p>

                # PLL1 Reference Selection. 0x0 - 5MHz, 0x1 - 9.6MHz, 0x2 - 10MHz, 0x3 - 12MHz, 0x4 - 13MHz, 0x5 - 19.2MHz, 0x6 - 20MHz, 0x7 - 
                # 4MHz, 0x8 - 26MHz, 0x9 - 27MHz, 0xA - 38.4MHz, 0xB - 40MHz, 0xC - 52MHz, 0xD - 100MHz, 0xE - 108MHz, 0xF - 125MHz, 0x10 - 135
                # Hz, 0x11 - 150 MHz. 0x12 to 0x1F - Reserved
                # PSU_SERDES_PLL_REF_SEL1_PLLREFSEL1                                              0x9

                # PLL1 Reference Selection Register
                #(OFFSET, MASK, VALUE)      (0XFD410004, 0x0000001FU ,0x00000009U)  */
    mask_write 0XFD410004 0x0000001F 0x00000009
                # Register : PLL_REF_SEL2 @ 0XFD410008</p>

                # PLL2 Reference Selection. 0x0 - 5MHz, 0x1 - 9.6MHz, 0x2 - 10MHz, 0x3 - 12MHz, 0x4 - 13MHz, 0x5 - 19.2MHz, 0x6 - 20MHz, 0x7 - 
                # 4MHz, 0x8 - 26MHz, 0x9 - 27MHz, 0xA - 38.4MHz, 0xB - 40MHz, 0xC - 52MHz, 0xD - 100MHz, 0xE - 108MHz, 0xF - 125MHz, 0x10 - 135
                # Hz, 0x11 - 150 MHz. 0x12 to 0x1F - Reserved
                # PSU_SERDES_PLL_REF_SEL2_PLLREFSEL2                                              0x8

                # PLL2 Reference Selection Register
                #(OFFSET, MASK, VALUE)      (0XFD410008, 0x0000001FU ,0x00000008U)  */
    mask_write 0XFD410008 0x0000001F 0x00000008
                # Register : PLL_REF_SEL3 @ 0XFD41000C</p>

                # PLL3 Reference Selection. 0x0 - 5MHz, 0x1 - 9.6MHz, 0x2 - 10MHz, 0x3 - 12MHz, 0x4 - 13MHz, 0x5 - 19.2MHz, 0x6 - 20MHz, 0x7 - 
                # 4MHz, 0x8 - 26MHz, 0x9 - 27MHz, 0xA - 38.4MHz, 0xB - 40MHz, 0xC - 52MHz, 0xD - 100MHz, 0xE - 108MHz, 0xF - 125MHz, 0x10 - 135
                # Hz, 0x11 - 150 MHz. 0x12 to 0x1F - Reserved
                # PSU_SERDES_PLL_REF_SEL3_PLLREFSEL3                                              0xF

                # PLL3 Reference Selection Register
                #(OFFSET, MASK, VALUE)      (0XFD41000C, 0x0000001FU ,0x0000000FU)  */
    mask_write 0XFD41000C 0x0000001F 0x0000000F
                # : GT REFERENCE CLOCK FREQUENCY SELECTION
                # Register : L0_L0_REF_CLK_SEL @ 0XFD402860</p>

                # Sel of lane 0 ref clock local mux. Set to 1 to select lane 0 slicer output. Set to 0 to select lane0 ref clock mux output.
                # PSU_SERDES_L0_L0_REF_CLK_SEL_L0_REF_CLK_LCL_SEL                                 0x1

                # Lane0 Ref Clock Selection Register
                #(OFFSET, MASK, VALUE)      (0XFD402860, 0x00000080U ,0x00000080U)  */
    mask_write 0XFD402860 0x00000080 0x00000080
                # Register : L0_L1_REF_CLK_SEL @ 0XFD402864</p>

                # Sel of lane 1 ref clock local mux. Set to 1 to select lane 1 slicer output. Set to 0 to select lane1 ref clock mux output.
                # PSU_SERDES_L0_L1_REF_CLK_SEL_L1_REF_CLK_LCL_SEL                                 0x0

                # Bit 3 of lane 1 ref clock mux one hot sel. Set to 1 to select lane 3 slicer output from ref clock network
                # PSU_SERDES_L0_L1_REF_CLK_SEL_L1_REF_CLK_SEL_3                                   0x1

                # Lane1 Ref Clock Selection Register
                #(OFFSET, MASK, VALUE)      (0XFD402864, 0x00000088U ,0x00000008U)  */
    mask_write 0XFD402864 0x00000088 0x00000008
                # Register : L0_L2_REF_CLK_SEL @ 0XFD402868</p>

                # Sel of lane 2 ref clock local mux. Set to 1 to select lane 1 slicer output. Set to 0 to select lane2 ref clock mux output.
                # PSU_SERDES_L0_L2_REF_CLK_SEL_L2_REF_CLK_LCL_SEL                                 0x1

                # Lane2 Ref Clock Selection Register
                #(OFFSET, MASK, VALUE)      (0XFD402868, 0x00000080U ,0x00000080U)  */
    mask_write 0XFD402868 0x00000080 0x00000080
                # Register : L0_L3_REF_CLK_SEL @ 0XFD40286C</p>

                # Sel of lane 3 ref clock local mux. Set to 1 to select lane 3 slicer output. Set to 0 to select lane3 ref clock mux output.
                # PSU_SERDES_L0_L3_REF_CLK_SEL_L3_REF_CLK_LCL_SEL                                 0x0

                # Bit 1 of lane 3 ref clock mux one hot sel. Set to 1 to select lane 1 slicer output from ref clock network
                # PSU_SERDES_L0_L3_REF_CLK_SEL_L3_REF_CLK_SEL_1                                   0x1

                # Lane3 Ref Clock Selection Register
                #(OFFSET, MASK, VALUE)      (0XFD40286C, 0x00000082U ,0x00000002U)  */
    mask_write 0XFD40286C 0x00000082 0x00000002
                # : ENABLE SPREAD SPECTRUM
                # Register : L2_TM_PLL_DIG_37 @ 0XFD40A094</p>

                # Enable/Disable coarse code satureation limiting logic
                # PSU_SERDES_L2_TM_PLL_DIG_37_TM_ENABLE_COARSE_SATURATION                         0x1

                # Test mode register 37
                #(OFFSET, MASK, VALUE)      (0XFD40A094, 0x00000010U ,0x00000010U)  */
    mask_write 0XFD40A094 0x00000010 0x00000010
                # Register : L2_PLL_SS_STEPS_0_LSB @ 0XFD40A368</p>

                # Spread Spectrum No of Steps [7:0]
                # PSU_SERDES_L2_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB                          0x38

                # Spread Spectrum No of Steps bits 7:0
                #(OFFSET, MASK, VALUE)      (0XFD40A368, 0x000000FFU ,0x00000038U)  */
    mask_write 0XFD40A368 0x000000FF 0x00000038
                # Register : L2_PLL_SS_STEPS_1_MSB @ 0XFD40A36C</p>

                # Spread Spectrum No of Steps [10:8]
                # PSU_SERDES_L2_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB                          0x03

                # Spread Spectrum No of Steps bits 10:8
                #(OFFSET, MASK, VALUE)      (0XFD40A36C, 0x00000007U ,0x00000003U)  */
    mask_write 0XFD40A36C 0x00000007 0x00000003
                # Register : L3_PLL_SS_STEPS_0_LSB @ 0XFD40E368</p>

                # Spread Spectrum No of Steps [7:0]
                # PSU_SERDES_L3_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB                          0x0

                # Spread Spectrum No of Steps bits 7:0
                #(OFFSET, MASK, VALUE)      (0XFD40E368, 0x000000FFU ,0x00000000U)  */
    mask_write 0XFD40E368 0x000000FF 0x00000000
                # Register : L3_PLL_SS_STEPS_1_MSB @ 0XFD40E36C</p>

                # Spread Spectrum No of Steps [10:8]
                # PSU_SERDES_L3_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB                          0x0

                # Spread Spectrum No of Steps bits 10:8
                #(OFFSET, MASK, VALUE)      (0XFD40E36C, 0x00000007U ,0x00000000U)  */
    mask_write 0XFD40E36C 0x00000007 0x00000000
                # Register : L1_PLL_SS_STEPS_0_LSB @ 0XFD406368</p>

                # Spread Spectrum No of Steps [7:0]
                # PSU_SERDES_L1_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB                          0x0

                # Spread Spectrum No of Steps bits 7:0
                #(OFFSET, MASK, VALUE)      (0XFD406368, 0x000000FFU ,0x00000000U)  */
    mask_write 0XFD406368 0x000000FF 0x00000000
                # Register : L1_PLL_SS_STEPS_1_MSB @ 0XFD40636C</p>

                # Spread Spectrum No of Steps [10:8]
                # PSU_SERDES_L1_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB                          0x0

                # Spread Spectrum No of Steps bits 10:8
                #(OFFSET, MASK, VALUE)      (0XFD40636C, 0x00000007U ,0x00000000U)  */
    mask_write 0XFD40636C 0x00000007 0x00000000
                # Register : L1_PLL_SS_STEP_SIZE_0_LSB @ 0XFD406370</p>

                # Step Size for Spread Spectrum [7:0]
                # PSU_SERDES_L1_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB                         0x0

                # Step Size for Spread Spectrum LSB
                #(OFFSET, MASK, VALUE)      (0XFD406370, 0x000000FFU ,0x00000000U)  */
    mask_write 0XFD406370 0x000000FF 0x00000000
                # Register : L1_PLL_SS_STEP_SIZE_1 @ 0XFD406374</p>

                # Step Size for Spread Spectrum [15:8]
                # PSU_SERDES_L1_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1                                 0x0

                # Step Size for Spread Spectrum 1
                #(OFFSET, MASK, VALUE)      (0XFD406374, 0x000000FFU ,0x00000000U)  */
    mask_write 0XFD406374 0x000000FF 0x00000000
                # Register : L1_PLL_SS_STEP_SIZE_2 @ 0XFD406378</p>

                # Step Size for Spread Spectrum [23:16]
                # PSU_SERDES_L1_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2                                 0x0

                # Step Size for Spread Spectrum 2
                #(OFFSET, MASK, VALUE)      (0XFD406378, 0x000000FFU ,0x00000000U)  */
    mask_write 0XFD406378 0x000000FF 0x00000000
                # Register : L1_PLL_SS_STEP_SIZE_3_MSB @ 0XFD40637C</p>

                # Step Size for Spread Spectrum [25:24]
                # PSU_SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB                         0x0

                # Enable/Disable test mode force on SS step size
                # PSU_SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE                         0x1

                # Enable/Disable test mode force on SS no of steps
                # PSU_SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS                      0x1

                # Enable force on enable Spread Spectrum
                #(OFFSET, MASK, VALUE)      (0XFD40637C, 0x00000033U ,0x00000030U)  */
    mask_write 0XFD40637C 0x00000033 0x00000030
                # Register : L2_PLL_SS_STEP_SIZE_0_LSB @ 0XFD40A370</p>

                # Step Size for Spread Spectrum [7:0]
                # PSU_SERDES_L2_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB                         0xF4

                # Step Size for Spread Spectrum LSB
                #(OFFSET, MASK, VALUE)      (0XFD40A370, 0x000000FFU ,0x000000F4U)  */
    mask_write 0XFD40A370 0x000000FF 0x000000F4
                # Register : L2_PLL_SS_STEP_SIZE_1 @ 0XFD40A374</p>

                # Step Size for Spread Spectrum [15:8]
                # PSU_SERDES_L2_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1                                 0x31

                # Step Size for Spread Spectrum 1
                #(OFFSET, MASK, VALUE)      (0XFD40A374, 0x000000FFU ,0x00000031U)  */
    mask_write 0XFD40A374 0x000000FF 0x00000031
                # Register : L2_PLL_SS_STEP_SIZE_2 @ 0XFD40A378</p>

                # Step Size for Spread Spectrum [23:16]
                # PSU_SERDES_L2_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2                                 0x2

                # Step Size for Spread Spectrum 2
                #(OFFSET, MASK, VALUE)      (0XFD40A378, 0x000000FFU ,0x00000002U)  */
    mask_write 0XFD40A378 0x000000FF 0x00000002
                # Register : L2_PLL_SS_STEP_SIZE_3_MSB @ 0XFD40A37C</p>

                # Step Size for Spread Spectrum [25:24]
                # PSU_SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB                         0x0

                # Enable/Disable test mode force on SS step size
                # PSU_SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE                         0x1

                # Enable/Disable test mode force on SS no of steps
                # PSU_SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS                      0x1

                # Enable force on enable Spread Spectrum
                #(OFFSET, MASK, VALUE)      (0XFD40A37C, 0x00000033U ,0x00000030U)  */
    mask_write 0XFD40A37C 0x00000033 0x00000030
                # Register : L3_PLL_SS_STEP_SIZE_0_LSB @ 0XFD40E370</p>

                # Step Size for Spread Spectrum [7:0]
                # PSU_SERDES_L3_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB                         0x0

                # Step Size for Spread Spectrum LSB
                #(OFFSET, MASK, VALUE)      (0XFD40E370, 0x000000FFU ,0x00000000U)  */
    mask_write 0XFD40E370 0x000000FF 0x00000000
                # Register : L3_PLL_SS_STEP_SIZE_1 @ 0XFD40E374</p>

                # Step Size for Spread Spectrum [15:8]
                # PSU_SERDES_L3_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1                                 0x0

                # Step Size for Spread Spectrum 1
                #(OFFSET, MASK, VALUE)      (0XFD40E374, 0x000000FFU ,0x00000000U)  */
    mask_write 0XFD40E374 0x000000FF 0x00000000
                # Register : L3_PLL_SS_STEP_SIZE_2 @ 0XFD40E378</p>

                # Step Size for Spread Spectrum [23:16]
                # PSU_SERDES_L3_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2                                 0x0

                # Step Size for Spread Spectrum 2
                #(OFFSET, MASK, VALUE)      (0XFD40E378, 0x000000FFU ,0x00000000U)  */
    mask_write 0XFD40E378 0x000000FF 0x00000000
                # Register : L3_PLL_SS_STEP_SIZE_3_MSB @ 0XFD40E37C</p>

                # Step Size for Spread Spectrum [25:24]
                # PSU_SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB                         0x0

                # Enable/Disable test mode force on SS step size
                # PSU_SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE                         0x1

                # Enable/Disable test mode force on SS no of steps
                # PSU_SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS                      0x1

                # Enable test mode forcing on enable Spread Spectrum
                # PSU_SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_TM_FORCE_EN_SS                             0x1

                # Enable force on enable Spread Spectrum
                #(OFFSET, MASK, VALUE)      (0XFD40E37C, 0x000000B3U ,0x000000B0U)  */
    mask_write 0XFD40E37C 0x000000B3 0x000000B0
                # Register : L2_TM_DIG_6 @ 0XFD40906C</p>

                # Bypass Descrambler
                # PSU_SERDES_L2_TM_DIG_6_BYPASS_DESCRAM                                           0x1

                # Enable Bypass for <1> TM_DIG_CTRL_6
                # PSU_SERDES_L2_TM_DIG_6_FORCE_BYPASS_DESCRAM                                     0x1

                # Data path test modes in decoder and descram
                #(OFFSET, MASK, VALUE)      (0XFD40906C, 0x00000003U ,0x00000003U)  */
    mask_write 0XFD40906C 0x00000003 0x00000003
                # Register : L2_TX_DIG_TM_61 @ 0XFD4080F4</p>

                # Bypass scrambler signal
                # PSU_SERDES_L2_TX_DIG_TM_61_BYPASS_SCRAM                                         0x1

                # Enable/disable scrambler bypass signal
                # PSU_SERDES_L2_TX_DIG_TM_61_FORCE_BYPASS_SCRAM                                   0x1

                # MPHY PLL Gear and bypass scrambler
                #(OFFSET, MASK, VALUE)      (0XFD4080F4, 0x00000003U ,0x00000003U)  */
    mask_write 0XFD4080F4 0x00000003 0x00000003
                # Register : L3_PLL_FBDIV_FRAC_3_MSB @ 0XFD40E360</p>

                # Enable test mode force on fractional mode enable
                # PSU_SERDES_L3_PLL_FBDIV_FRAC_3_MSB_TM_FORCE_EN_FRAC                             0x1

                # Fractional feedback division control and fractional value for feedback division bits 26:24
                #(OFFSET, MASK, VALUE)      (0XFD40E360, 0x00000040U ,0x00000040U)  */
    mask_write 0XFD40E360 0x00000040 0x00000040
                # Register : L3_TM_DIG_6 @ 0XFD40D06C</p>

                # Bypass 8b10b decoder
                # PSU_SERDES_L3_TM_DIG_6_BYPASS_DECODER                                           0x1

                # Enable Bypass for <3> TM_DIG_CTRL_6
                # PSU_SERDES_L3_TM_DIG_6_FORCE_BYPASS_DEC                                         0x1

                # Bypass Descrambler
                # PSU_SERDES_L3_TM_DIG_6_BYPASS_DESCRAM                                           0x1

                # Enable Bypass for <1> TM_DIG_CTRL_6
                # PSU_SERDES_L3_TM_DIG_6_FORCE_BYPASS_DESCRAM                                     0x1

                # Data path test modes in decoder and descram
                #(OFFSET, MASK, VALUE)      (0XFD40D06C, 0x0000000FU ,0x0000000FU)  */
    mask_write 0XFD40D06C 0x0000000F 0x0000000F
                # Register : L3_TX_DIG_TM_61 @ 0XFD40C0F4</p>

                # Enable/disable encoder bypass signal
                # PSU_SERDES_L3_TX_DIG_TM_61_BYPASS_ENC                                           0x1

                # Bypass scrambler signal
                # PSU_SERDES_L3_TX_DIG_TM_61_BYPASS_SCRAM                                         0x1

                # Enable/disable scrambler bypass signal
                # PSU_SERDES_L3_TX_DIG_TM_61_FORCE_BYPASS_SCRAM                                   0x1

                # MPHY PLL Gear and bypass scrambler
                #(OFFSET, MASK, VALUE)      (0XFD40C0F4, 0x0000000BU ,0x0000000BU)  */
    mask_write 0XFD40C0F4 0x0000000B 0x0000000B
                # Register : L3_TXPMA_ST_0 @ 0XFD40CB00</p>

                # PHY Mode: 4'b000 - PCIe, 4'b001 - USB3, 4'b0010 - SATA, 4'b0100 - SGMII, 4'b0101 - DP, 4'b1000 - MPHY
                # PSU_SERDES_L3_TXPMA_ST_0_TX_PHY_MODE                                            0x21

                # Opmode Info
                #(OFFSET, MASK, VALUE)      (0XFD40CB00, 0x000000F0U ,0x000000F0U)  */
    mask_write 0XFD40CB00 0x000000F0 0x000000F0
                # : GT LANE SETTINGS
                # Register : ICM_CFG0 @ 0XFD410010</p>

                # Controls UPHY Lane 0 protocol configuration. 0 - PowerDown, 1 - PCIe .0, 2 - Sata0, 3 - USB0, 4 - DP.1, 5 - SGMII0, 6 - Unuse
                # , 7 - Unused
                # PSU_SERDES_ICM_CFG0_L0_ICM_CFG                                                  1

                # Controls UPHY Lane 1 protocol configuration. 0 - PowerDown, 1 - PCIe.1, 2 - Sata1, 3 - USB0, 4 - DP.0, 5 - SGMII1, 6 - Unused
                #  7 - Unused
                # PSU_SERDES_ICM_CFG0_L1_ICM_CFG                                                  4

                # ICM Configuration Register 0
                #(OFFSET, MASK, VALUE)      (0XFD410010, 0x00000077U ,0x00000041U)  */
    mask_write 0XFD410010 0x00000077 0x00000041
                # Register : ICM_CFG1 @ 0XFD410014</p>

                # Controls UPHY Lane 2 protocol configuration. 0 - PowerDown, 1 - PCIe.1, 2 - Sata0, 3 - USB0, 4 - DP.1, 5 - SGMII2, 6 - Unused
                #  7 - Unused
                # PSU_SERDES_ICM_CFG1_L2_ICM_CFG                                                  3

                # Controls UPHY Lane 3 protocol configuration. 0 - PowerDown, 1 - PCIe.3, 2 - Sata1, 3 - USB1, 4 - DP.0, 5 - SGMII3, 6 - Unused
                #  7 - Unused
                # PSU_SERDES_ICM_CFG1_L3_ICM_CFG                                                  2

                # ICM Configuration Register 1
                #(OFFSET, MASK, VALUE)      (0XFD410014, 0x00000077U ,0x00000023U)  */
    mask_write 0XFD410014 0x00000077 0x00000023
                # : CHECKING PLL LOCK
                # : ENABLE SERIAL DATA MUX DEEMPH
                # Register : L1_TXPMD_TM_45 @ 0XFD404CB4</p>

                # Enable/disable DP post2 path
                # PSU_SERDES_L1_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_POST2_PATH                         0x1

                # Override enable/disable of DP post2 path
                # PSU_SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST2_PATH                    0x1

                # Override enable/disable of DP post1 path
                # PSU_SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST1_PATH                    0x1

                # Enable/disable DP main path
                # PSU_SERDES_L1_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_MAIN_PATH                          0x1

                # Override enable/disable of DP main path
                # PSU_SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_MAIN_PATH                     0x1

                # Post or pre or main DP path selection
                #(OFFSET, MASK, VALUE)      (0XFD404CB4, 0x00000037U ,0x00000037U)  */
    mask_write 0XFD404CB4 0x00000037 0x00000037
                # Register : L1_TX_ANA_TM_118 @ 0XFD4041D8</p>

                # Test register force for enabling/disablign TX deemphasis bits <17:0>
                # PSU_SERDES_L1_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0                                0x1

                # Enable Override of TX deemphasis
                #(OFFSET, MASK, VALUE)      (0XFD4041D8, 0x00000001U ,0x00000001U)  */
    mask_write 0XFD4041D8 0x00000001 0x00000001
                # : ENABLE PRE EMPHAIS AND VOLTAGE SWING
                # Register : L1_TXPMD_TM_48 @ 0XFD404CC0</p>

                # Margining factor value
                # PSU_SERDES_L1_TXPMD_TM_48_TM_RESULTANT_MARGINING_FACTOR                         0

                # Margining factor
                #(OFFSET, MASK, VALUE)      (0XFD404CC0, 0x0000001FU ,0x00000000U)  */
    mask_write 0XFD404CC0 0x0000001F 0x00000000
                # Register : L1_TX_ANA_TM_18 @ 0XFD404048</p>

                # pipe_TX_Deemph. 0: -6dB de-emphasis, 1: -3.5dB de-emphasis, 2 : No de-emphasis, Others: reserved
                # PSU_SERDES_L1_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0                                   0

                # Override for PIPE TX de-emphasis
                #(OFFSET, MASK, VALUE)      (0XFD404048, 0x000000FFU ,0x00000000U)  */
    mask_write 0XFD404048 0x000000FF 0x00000000
}

set psu_resetout_init_data {
                # : TAKING SERDES PERIPHERAL OUT OF RESET RESET
                # : PUTTING USB0 IN RESET
                # Register : RST_LPD_TOP @ 0XFF5E023C</p>

                # USB 0 reset for control registers
                # PSU_CRL_APB_RST_LPD_TOP_USB0_APB_RESET                                          0X0

                # Software control register for the LPD block.
                #(OFFSET, MASK, VALUE)      (0XFF5E023C, 0x00000400U ,0x00000000U)  */
    mask_write 0XFF5E023C 0x00000400 0x00000000
                # : USB0 PIPE POWER PRESENT
                # Register : fpd_power_prsnt @ 0XFF9D0080</p>

                # This bit is used to choose between PIPE power present and 1'b1
                # PSU_USB3_0_FPD_POWER_PRSNT_OPTION                                               0X1

                # fpd_power_prsnt
                #(OFFSET, MASK, VALUE)      (0XFF9D0080, 0x00000001U ,0x00000001U)  */
    mask_write 0XFF9D0080 0x00000001 0x00000001
                # : 
                # Register : RST_LPD_TOP @ 0XFF5E023C</p>

                # USB 0 sleep circuit reset
                # PSU_CRL_APB_RST_LPD_TOP_USB0_HIBERRESET                                         0X0

                # USB 0 reset
                # PSU_CRL_APB_RST_LPD_TOP_USB0_CORERESET                                          0X0

                # Software control register for the LPD block.
                #(OFFSET, MASK, VALUE)      (0XFF5E023C, 0x00000140U ,0x00000000U)  */
    mask_write 0XFF5E023C 0x00000140 0x00000000
                # : PUTTING GEM0 IN RESET
                # Register : RST_LPD_IOU0 @ 0XFF5E0230</p>

                # GEM 3 reset
                # PSU_CRL_APB_RST_LPD_IOU0_GEM3_RESET                                             0X0

                # Software controlled reset for the GEMs
                #(OFFSET, MASK, VALUE)      (0XFF5E0230, 0x00000008U ,0x00000000U)  */
    mask_write 0XFF5E0230 0x00000008 0x00000000
                # : PUTTING SATA IN RESET
                # Register : sata_misc_ctrl @ 0XFD3D0100</p>

                # Sata PM clock control select
                # PSU_SIOU_SATA_MISC_CTRL_SATA_PM_CLK_SEL                                         0x3

                # Misc Contorls for SATA.This register may only be modified during bootup (while SATA block is disabled)
                #(OFFSET, MASK, VALUE)      (0XFD3D0100, 0x00000003U ,0x00000003U)  */
    mask_write 0XFD3D0100 0x00000003 0x00000003
                # Register : RST_FPD_TOP @ 0XFD1A0100</p>

                # Sata block level reset
                # PSU_CRF_APB_RST_FPD_TOP_SATA_RESET                                              0X0

                # FPD Block level software controlled reset
                #(OFFSET, MASK, VALUE)      (0XFD1A0100, 0x00000002U ,0x00000000U)  */
    mask_write 0XFD1A0100 0x00000002 0x00000000
                # : PUTTING PCIE IN RESET
                # Register : RST_FPD_TOP @ 0XFD1A0100</p>

                # PCIE config reset
                # PSU_CRF_APB_RST_FPD_TOP_PCIE_CFG_RESET                                          0X0

                # PCIE control block level reset
                # PSU_CRF_APB_RST_FPD_TOP_PCIE_CTRL_RESET                                         0X0

                # PCIE bridge block level reset (AXI interface)
                # PSU_CRF_APB_RST_FPD_TOP_PCIE_BRIDGE_RESET                                       0X0

                # FPD Block level software controlled reset
                #(OFFSET, MASK, VALUE)      (0XFD1A0100, 0x000E0000U ,0x00000000U)  */
    mask_write 0XFD1A0100 0x000E0000 0x00000000
                # : PUTTING DP IN RESET
                # Register : RST_FPD_TOP @ 0XFD1A0100</p>

                # Display Port block level reset (includes DPDMA)
                # PSU_CRF_APB_RST_FPD_TOP_DP_RESET                                                0X0

                # FPD Block level software controlled reset
                #(OFFSET, MASK, VALUE)      (0XFD1A0100, 0x00010000U ,0x00000000U)  */
    mask_write 0XFD1A0100 0x00010000 0x00000000
                # Register : DP_PHY_RESET @ 0XFD4A0200</p>

                # Set to '1' to hold the GT in reset. Clear to release.
                # PSU_DP_DP_PHY_RESET_GT_RESET                                                    0X0

                # Reset the transmitter PHY.
                #(OFFSET, MASK, VALUE)      (0XFD4A0200, 0x00000002U ,0x00000000U)  */
    mask_write 0XFD4A0200 0x00000002 0x00000000
                # Register : DP_TX_PHY_POWER_DOWN @ 0XFD4A0238</p>

                # Two bits per lane. When set to 11, moves the GT to power down mode. When set to 00, GT will be in active state. bits [1:0] - 
                # ane0 Bits [3:2] - lane 1
                # PSU_DP_DP_TX_PHY_POWER_DOWN_POWER_DWN                                           0X0

                # Control PHY Power down
                #(OFFSET, MASK, VALUE)      (0XFD4A0238, 0x0000000FU ,0x00000000U)  */
    mask_write 0XFD4A0238 0x0000000F 0x00000000
                # : USB0 GFLADJ
                # Register : GUSB2PHYCFG @ 0XFE20C200</p>

                # USB 2.0 Turnaround Time (USBTrdTim) Sets the turnaround time in PHY clocks. Specifies the response time for a MAC request to 
                # he Packet FIFO Controller (PFC) to fetch data from the DFIFO (SPRAM). The following are the required values for the minimum S
                # C bus frequency of 60 MHz. USB turnaround time is a critical certification criteria when using long cables and five hub level
                # . The required values for this field: - 4'h5: When the MAC interface is 16-bit UTMI+. - 4'h9: When the MAC interface is 8-bit
                # UTMI+/ULPI. If SoC bus clock is less than 60 MHz, and USB turnaround time is not critical, this field can be set to a larger 
                # alue. Note: This field is valid only in device mode.
                # PSU_USB3_0_XHCI_GUSB2PHYCFG_USBTRDTIM                                           0X9

                # Transceiver Delay: Enables a delay between the assertion of the UTMI/ULPI Transceiver Select signal (for HS) and the assertio
                #  of the TxValid signal during a HS Chirp. When this bit is set to 1, a delay (of approximately 2.5 us) is introduced from the
                # time when the Transceiver Select is set to 2'b00 (HS) to the time the TxValid is driven to 0 for sending the chirp-K. This de
                # ay is required for some UTMI/ULPI PHYs. Note: - If you enable the hibernation feature when the device core comes out of power
                # off, you must re-initialize this bit with the appropriate value because the core does not save and restore this bit value dur
                # ng hibernation. - This bit is valid only in device mode.
                # PSU_USB3_0_XHCI_GUSB2PHYCFG_XCVRDLY                                             0X0

                # Enable utmi_sleep_n and utmi_l1_suspend_n (EnblSlpM) The application uses this bit to control utmi_sleep_n and utmi_l1_suspen
                # _n assertion to the PHY in the L1 state. - 1'b0: utmi_sleep_n and utmi_l1_suspend_n assertion from the core is not transferre
                #  to the external PHY. - 1'b1: utmi_sleep_n and utmi_l1_suspend_n assertion from the core is transferred to the external PHY. 
                # ote: This bit must be set high for Port0 if PHY is used. Note: In Device mode - Before issuing any device endpoint command wh
                # n operating in 2.0 speeds, disable this bit and enable it after the command completes. Without disabling this bit, if a comma
                # d is issued when the device is in L1 state and if mac2_clk (utmi_clk/ulpi_clk) is gated off, the command will not get complet
                # d.
                # PSU_USB3_0_XHCI_GUSB2PHYCFG_ENBLSLPM                                            0X0

                # USB 2.0 High-Speed PHY or USB 1.1 Full-Speed Serial Transceiver Select The application uses this bit to select a high-speed P
                # Y or a full-speed transceiver. - 1'b0: USB 2.0 high-speed UTMI+ or ULPI PHY. This bit is always 0, with Write Only access. - 
                # 'b1: USB 1.1 full-speed serial transceiver. This bit is always 1, with Write Only access. If both interface types are selecte
                #  in coreConsultant (that is, parameters' values are not zero), the application uses this bit to select the active interface i
                #  active, with Read-Write bit access. Note: USB 1.1 full-serial transceiver is not supported. This bit always reads as 1'b0.
                # PSU_USB3_0_XHCI_GUSB2PHYCFG_PHYSEL                                              0X0

                # Suspend USB2.0 HS/FS/LS PHY (SusPHY) When set, USB2.0 PHY enters Suspend mode if Suspend conditions are valid. For DRD/OTG co
                # figurations, it is recommended that this bit is set to 0 during coreConsultant configuration. If it is set to 1, then the app
                # ication must clear this bit after power-on reset. Application needs to set it to 1 after the core initialization completes. F
                # r all other configurations, this bit can be set to 1 during core configuration. Note: - In host mode, on reset, this bit is s
                # t to 1. Software can override this bit after reset. - In device mode, before issuing any device endpoint command when operati
                # g in 2.0 speeds, disable this bit and enable it after the command completes. If you issue a command without disabling this bi
                #  when the device is in L2 state and if mac2_clk (utmi_clk/ulpi_clk) is gated off, the command will not get completed.
                # PSU_USB3_0_XHCI_GUSB2PHYCFG_SUSPENDUSB20                                        0X1

                # Full-Speed Serial Interface Select (FSIntf) The application uses this bit to select a unidirectional or bidirectional USB 1.1
                # full-speed serial transceiver interface. - 1'b0: 6-pin unidirectional full-speed serial interface. This bit is set to 0 with 
                # ead Only access. - 1'b1: 3-pin bidirectional full-speed serial interface. This bit is set to 0 with Read Only access. Note: U
                # B 1.1 full-speed serial interface is not supported. This bit always reads as 1'b0.
                # PSU_USB3_0_XHCI_GUSB2PHYCFG_FSINTF                                              0X0

                # ULPI or UTMI+ Select (ULPI_UTMI_Sel) The application uses this bit to select a UTMI+ or ULPI Interface. - 1'b0: UTMI+ Interfa
                # e - 1'b1: ULPI Interface This bit is writable only if UTMI+ and ULPI is specified for High-Speed PHY Interface(s) in coreCons
                # ltant configuration (DWC_USB3_HSPHY_INTERFACE = 3). Otherwise, this bit is read-only and the value depends on the interface s
                # lected through DWC_USB3_HSPHY_INTERFACE.
                # PSU_USB3_0_XHCI_GUSB2PHYCFG_ULPI_UTMI_SEL                                       0X1

                # PHY Interface (PHYIf) If UTMI+ is selected, the application uses this bit to configure the core to support a UTMI+ PHY with a
                #  8- or 16-bit interface. - 1'b0: 8 bits - 1'b1: 16 bits ULPI Mode: 1'b0 Note: - All the enabled 2.0 ports must have the same 
                # lock frequency as Port0 clock frequency (utmi_clk[0]). - The UTMI 8-bit and 16-bit modes cannot be used together for differen
                #  ports at the same time (that is, all the ports must be in 8-bit mode, or all of them must be in 16-bit mode, at a time). - I
                #  any of the USB 2.0 ports is selected as ULPI port for operation, then all the USB 2.0 ports must be operating at 60 MHz.
                # PSU_USB3_0_XHCI_GUSB2PHYCFG_PHYIF                                               0X0

                # HS/FS Timeout Calibration (TOutCal) The number of PHY clocks, as indicated by the application in this field, is multiplied by
                # a bit-time factor; this factor is added to the high-speed/full-speed interpacket timeout duration in the core to account for 
                # dditional delays introduced by the PHY. This may be required, since the delay introduced by the PHY in generating the linesta
                # e condition may vary among PHYs. The USB standard timeout value for high-speed operation is 736 to 816 (inclusive) bit times.
                # The USB standard timeout value for full-speed operation is 16 to 18 (inclusive) bit times. The application must program this 
                # ield based on the speed of connection. The number of bit times added per PHY clock are: High-speed operation: - One 30-MHz PH
                #  clock = 16 bit times - One 60-MHz PHY clock = 8 bit times Full-speed operation: - One 30-MHz PHY clock = 0.4 bit times - One
                # 60-MHz PHY clock = 0.2 bit times - One 48-MHz PHY clock = 0.25 bit times
                # PSU_USB3_0_XHCI_GUSB2PHYCFG_TOUTCAL                                             0X7

                # Global USB2 PHY Configuration Register The application must program this register before starting any transactions on either 
                # he SoC bus or the USB. In Device-only configurations, only one register is needed. In Host mode, per-port registers are imple
                # ented.
                #(OFFSET, MASK, VALUE)      (0XFE20C200, 0x00003FFFU ,0x00002457U)  */
    mask_write 0XFE20C200 0x00003FFF 0x00002457
                # Register : GFLADJ @ 0XFE20C630</p>

                # This field indicates the frame length adjustment to be applied when SOF/ITP counter is running on the ref_clk. This register 
                # alue is used to adjust the ITP interval when GCTL[SOFITPSYNC] is set to '1'; SOF and ITP interval when GLADJ.GFLADJ_REFCLK_LP
                # _SEL is set to '1'. This field must be programmed to a non-zero value only if GFLADJ_REFCLK_LPM_SEL is set to '1' or GCTL.SOF
                # TPSYNC is set to '1'. The value is derived as follows: FLADJ_REF_CLK_FLADJ=((125000/ref_clk_period_integer)-(125000/ref_clk_p
                # riod)) * ref_clk_period where - the ref_clk_period_integer is the integer value of the ref_clk period got by truncating the d
                # cimal (fractional) value that is programmed in the GUCTL.REF_CLK_PERIOD field. - the ref_clk_period is the ref_clk period inc
                # uding the fractional value. Examples: If the ref_clk is 24 MHz then - GUCTL.REF_CLK_PERIOD = 41 - GFLADJ.GLADJ_REFCLK_FLADJ =
                # ((125000/41)-(125000/41.6666))*41.6666 = 2032 (ignoring the fractional value) If the ref_clk is 48 MHz then - GUCTL.REF_CLK_P
                # RIOD = 20 - GFLADJ.GLADJ_REFCLK_FLADJ = ((125000/20)-(125000/20.8333))*20.8333 = 5208 (ignoring the fractional value)
                # PSU_USB3_0_XHCI_GFLADJ_GFLADJ_REFCLK_FLADJ                                      0X0

                # Global Frame Length Adjustment Register This register provides options for the software to control the core behavior with res
                # ect to SOF (Start of Frame) and ITP (Isochronous Timestamp Packet) timers and frame timer functionality. It provides an optio
                #  to override the fladj_30mhz_reg sideband signal. In addition, it enables running SOF or ITP frame timer counters completely 
                # rom the ref_clk. This facilitates hardware LPM in host mode with the SOF or ITP counters being run from the ref_clk signal.
                #(OFFSET, MASK, VALUE)      (0XFE20C630, 0x003FFF00U ,0x00000000U)  */
    mask_write 0XFE20C630 0x003FFF00 0x00000000
                # : CHECK PLL LOCK FOR LANE0
                # Register : L0_PLL_STATUS_READ_1 @ 0XFD4023E4</p>

                # Status Read value of PLL Lock
                # PSU_SERDES_L0_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ                            1
    mask_poll 0XFD4023E4 0x00000010
                # : CHECK PLL LOCK FOR LANE1
                # Register : L1_PLL_STATUS_READ_1 @ 0XFD4063E4</p>

                # Status Read value of PLL Lock
                # PSU_SERDES_L1_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ                            1
    mask_poll 0XFD4063E4 0x00000010
                # : CHECK PLL LOCK FOR LANE2
                # Register : L2_PLL_STATUS_READ_1 @ 0XFD40A3E4</p>

                # Status Read value of PLL Lock
                # PSU_SERDES_L2_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ                            1
    mask_poll 0XFD40A3E4 0x00000010
                # : CHECK PLL LOCK FOR LANE3
                # Register : L3_PLL_STATUS_READ_1 @ 0XFD40E3E4</p>

                # Status Read value of PLL Lock
                # PSU_SERDES_L3_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ                            1
    mask_poll 0XFD40E3E4 0x00000010
                # : UPDATING TWO PCIE REGISTERS DEFAULT VALUES, AS THESE REGISTERS HAVE INCORRECT RESET VALUES IN SILICON.
                # Register : ATTR_37 @ 0XFD480094</p>

                # Sets the ASPM Optionality Compliance bit, to comply with the 2.1 ASPM Optionality ECN. Transferred to the Link Capabilities r
                # gister.; EP=0x0001; RP=0x0001
                # PSU_PCIE_ATTRIB_ATTR_37_ATTR_LINK_CAP_ASPM_OPTIONALITY                          0X1

                # ATTR_37
                #(OFFSET, MASK, VALUE)      (0XFD480094, 0x00004000U ,0x00004000U)  */
    mask_write 0XFD480094 0x00004000 0x00004000
                # Register : ATTR_25 @ 0XFD480064</p>

                # If TRUE Completion Timeout Disable is supported. This is required to be TRUE for Endpoint and either setting allowed for Root
                # ports. Drives Device Capability 2 [4]; EP=0x0001; RP=0x0001
                # PSU_PCIE_ATTRIB_ATTR_25_ATTR_CPL_TIMEOUT_DISABLE_SUPPORTED                      0X1

                # ATTR_25
                #(OFFSET, MASK, VALUE)      (0XFD480064, 0x00000200U ,0x00000200U)  */
    mask_write 0XFD480064 0x00000200 0x00000200
                # : PCIE SETTINGS
                # Register : ATTR_7 @ 0XFD48001C</p>

                # Specifies mask/settings for Base Address Register (BAR) 0. If BAR is not to be implemented, set to 32'h00000000. Bits are def
                # ned as follows: Memory Space BAR [0] = Mem Space Indicator (set to 0) [2:1] = Type field (10 for 64-bit, 00 for 32-bit) [3] =
                # Prefetchable (0 or 1) [31:4] = Mask for writable bits of BAR; if 32-bit BAR, set uppermost 31:n bits to 1, where 2^n=memory a
                # erture size in bytes. If 64-bit BAR, set uppermost 63:n bits of \'7bBAR1,BAR0\'7d to 1. IO Space BAR 0] = IO Space Indicator 
                # set to 1) [1] = Reserved (set to 0) [31:2] = Mask for writable bits of BAR; set uppermost 31:n bits to 1, where 2^n=i/o apert
                # re size in bytes.; EP=0x0004; RP=0x0000
                # PSU_PCIE_ATTRIB_ATTR_7_ATTR_BAR0                                                0x0

                # ATTR_7
                #(OFFSET, MASK, VALUE)      (0XFD48001C, 0x0000FFFFU ,0x00000000U)  */
    mask_write 0XFD48001C 0x0000FFFF 0x00000000
                # Register : ATTR_8 @ 0XFD480020</p>

                # Specifies mask/settings for Base Address Register (BAR) 0. If BAR is not to be implemented, set to 32'h00000000. Bits are def
                # ned as follows: Memory Space BAR [0] = Mem Space Indicator (set to 0) [2:1] = Type field (10 for 64-bit, 00 for 32-bit) [3] =
                # Prefetchable (0 or 1) [31:4] = Mask for writable bits of BAR; if 32-bit BAR, set uppermost 31:n bits to 1, where 2^n=memory a
                # erture size in bytes. If 64-bit BAR, set uppermost 63:n bits of \'7bBAR1,BAR0\'7d to 1. IO Space BAR 0] = IO Space Indicator 
                # set to 1) [1] = Reserved (set to 0) [31:2] = Mask for writable bits of BAR; set uppermost 31:n bits to 1, where 2^n=i/o apert
                # re size in bytes.; EP=0xFFF0; RP=0x0000
                # PSU_PCIE_ATTRIB_ATTR_8_ATTR_BAR0                                                0x0

                # ATTR_8
                #(OFFSET, MASK, VALUE)      (0XFD480020, 0x0000FFFFU ,0x00000000U)  */
    mask_write 0XFD480020 0x0000FFFF 0x00000000
                # Register : ATTR_9 @ 0XFD480024</p>

                # Specifies mask/settings for Base Address Register (BAR) 1 if BAR0 is a 32-bit BAR, or the upper bits of \'7bBAR1,BAR0\'7d if 
                # AR0 is a 64-bit BAR. If BAR is not to be implemented, set to 32'h00000000. See BAR0 description if this functions as the uppe
                #  bits of a 64-bit BAR. Bits are defined as follows: Memory Space BAR (not upper bits of BAR0) [0] = Mem Space Indicator (set 
                # o 0) [2:1] = Type field (10 for 64-bit, 00 for 32-bit) [3] = Prefetchable (0 or 1) [31:4] = Mask for writable bits of BAR; if
                # 32-bit BAR, set uppermost 31:n bits to 1, where 2^n=memory aperture size in bytes. If 64-bit BAR, set uppermost 63:n bits of 
                # '7bBAR2,BAR1\'7d to 1. IO Space BAR 0] = IO Space Indicator (set to 1) [1] = Reserved (set to 0) [31:2] = Mask for writable b
                # ts of BAR; set uppermost 31:n bits to 1, where 2^n=i/o aperture size in bytes.; EP=0xFFFF; RP=0x0000
                # PSU_PCIE_ATTRIB_ATTR_9_ATTR_BAR1                                                0x0

                # ATTR_9
                #(OFFSET, MASK, VALUE)      (0XFD480024, 0x0000FFFFU ,0x00000000U)  */
    mask_write 0XFD480024 0x0000FFFF 0x00000000
                # Register : ATTR_10 @ 0XFD480028</p>

                # Specifies mask/settings for Base Address Register (BAR) 1 if BAR0 is a 32-bit BAR, or the upper bits of \'7bBAR1,BAR0\'7d if 
                # AR0 is a 64-bit BAR. If BAR is not to be implemented, set to 32'h00000000. See BAR0 description if this functions as the uppe
                #  bits of a 64-bit BAR. Bits are defined as follows: Memory Space BAR (not upper bits of BAR0) [0] = Mem Space Indicator (set 
                # o 0) [2:1] = Type field (10 for 64-bit, 00 for 32-bit) [3] = Prefetchable (0 or 1) [31:4] = Mask for writable bits of BAR; if
                # 32-bit BAR, set uppermost 31:n bits to 1, where 2^n=memory aperture size in bytes. If 64-bit BAR, set uppermost 63:n bits of 
                # '7bBAR2,BAR1\'7d to 1. IO Space BAR 0] = IO Space Indicator (set to 1) [1] = Reserved (set to 0) [31:2] = Mask for writable b
                # ts of BAR; set uppermost 31:n bits to 1, where 2^n=i/o aperture size in bytes.; EP=0xFFFF; RP=0x0000
                # PSU_PCIE_ATTRIB_ATTR_10_ATTR_BAR1                                               0x0

                # ATTR_10
                #(OFFSET, MASK, VALUE)      (0XFD480028, 0x0000FFFFU ,0x00000000U)  */
    mask_write 0XFD480028 0x0000FFFF 0x00000000
                # Register : ATTR_11 @ 0XFD48002C</p>

                # For an endpoint, specifies mask/settings for Base Address Register (BAR) 2 if BAR1 is a 32-bit BAR, or the upper bits of \'7b
                # AR2,BAR1\'7d if BAR1 is the lower part of a 64-bit BAR. If BAR is not to be implemented, set to 32'h00000000. See BAR1 descri
                # tion if this functions as the upper bits of a 64-bit BAR. For a switch or root: This must be set to 00FF_FFFF. For an endpoin
                # , bits are defined as follows: Memory Space BAR (not upper bits of BAR1) [0] = Mem Space Indicator (set to 0) [2:1] = Type fi
                # ld (10 for 64-bit, 00 for 32-bit) [3] = Prefetchable (0 or 1) [31:4] = Mask for writable bits of BAR; if 32-bit BAR, set uppe
                # most 31:n bits to 1, where 2^n=memory aperture size in bytes. If 64-bit BAR, set uppermost 63:n bits of \'7bBAR3,BAR2\'7d to 
                # . IO Space BAR 0] = IO Space Indicator (set to 1) [1] = Reserved (set to 0) [31:2] = Mask for writable bits of BAR; set upper
                # ost 31:n bits to 1, where 2^n=i/o aperture size in bytes.; EP=0x0004; RP=0xFFFF
                # PSU_PCIE_ATTRIB_ATTR_11_ATTR_BAR2                                               0xFFFF

                # ATTR_11
                #(OFFSET, MASK, VALUE)      (0XFD48002C, 0x0000FFFFU ,0x0000FFFFU)  */
    mask_write 0XFD48002C 0x0000FFFF 0x0000FFFF
                # Register : ATTR_12 @ 0XFD480030</p>

                # For an endpoint, specifies mask/settings for Base Address Register (BAR) 2 if BAR1 is a 32-bit BAR, or the upper bits of \'7b
                # AR2,BAR1\'7d if BAR1 is the lower part of a 64-bit BAR. If BAR is not to be implemented, set to 32'h00000000. See BAR1 descri
                # tion if this functions as the upper bits of a 64-bit BAR. For a switch or root: This must be set to 00FF_FFFF. For an endpoin
                # , bits are defined as follows: Memory Space BAR (not upper bits of BAR1) [0] = Mem Space Indicator (set to 0) [2:1] = Type fi
                # ld (10 for 64-bit, 00 for 32-bit) [3] = Prefetchable (0 or 1) [31:4] = Mask for writable bits of BAR; if 32-bit BAR, set uppe
                # most 31:n bits to 1, where 2^n=memory aperture size in bytes. If 64-bit BAR, set uppermost 63:n bits of \'7bBAR3,BAR2\'7d to 
                # . IO Space BAR 0] = IO Space Indicator (set to 1) [1] = Reserved (set to 0) [31:2] = Mask for writable bits of BAR; set upper
                # ost 31:n bits to 1, where 2^n=i/o aperture size in bytes.; EP=0xFFF0; RP=0x00FF
                # PSU_PCIE_ATTRIB_ATTR_12_ATTR_BAR2                                               0xFF

                # ATTR_12
                #(OFFSET, MASK, VALUE)      (0XFD480030, 0x0000FFFFU ,0x000000FFU)  */
    mask_write 0XFD480030 0x0000FFFF 0x000000FF
                # Register : ATTR_13 @ 0XFD480034</p>

                # For an endpoint, specifies mask/settings for Base Address Register (BAR) 3 if BAR2 is a 32-bit BAR, or the upper bits of \'7b
                # AR3,BAR2\'7d if BAR2 is the lower part of a 64-bit BAR. If BAR is not to be implemented, set to 32'h00000000. See BAR2 descri
                # tion if this functions as the upper bits of a 64-bit BAR. For a switch or root, this must be set to: FFFF_0000 = IO Limit/Bas
                #  Registers not implemented FFFF_F0F0 = IO Limit/Base Registers use 16-bit decode FFFF_F1F1 = IO Limit/Base Registers use 32-b
                # t decode For an endpoint, bits are defined as follows: Memory Space BAR (not upper bits of BAR2) [0] = Mem Space Indicator (s
                # t to 0) [2:1] = Type field (10 for 64-bit, 00 for 32-bit) [3] = Prefetchable (0 or 1) [31:4] = Mask for writable bits of BAR;
                # if 32-bit BAR, set uppermost 31:n bits to 1, where 2^n=memory aperture size in bytes. If 64-bit BAR, set uppermost 63:n bits 
                # f \'7bBAR4,BAR3\'7d to 1. IO Space BAR 0] = IO Space Indicator (set to 1) [1] = Reserved (set to 0) [31:2] = Mask for writabl
                #  bits of BAR; set uppermost 31:n bits to 1, where 2^n=i/o aperture size in bytes.; EP=0xFFFF; RP=0x0000
                # PSU_PCIE_ATTRIB_ATTR_13_ATTR_BAR3                                               0x0

                # ATTR_13
                #(OFFSET, MASK, VALUE)      (0XFD480034, 0x0000FFFFU ,0x00000000U)  */
    mask_write 0XFD480034 0x0000FFFF 0x00000000
                # Register : ATTR_14 @ 0XFD480038</p>

                # For an endpoint, specifies mask/settings for Base Address Register (BAR) 3 if BAR2 is a 32-bit BAR, or the upper bits of \'7b
                # AR3,BAR2\'7d if BAR2 is the lower part of a 64-bit BAR. If BAR is not to be implemented, set to 32'h00000000. See BAR2 descri
                # tion if this functions as the upper bits of a 64-bit BAR. For a switch or root, this must be set to: FFFF_0000 = IO Limit/Bas
                #  Registers not implemented FFFF_F0F0 = IO Limit/Base Registers use 16-bit decode FFFF_F1F1 = IO Limit/Base Registers use 32-b
                # t decode For an endpoint, bits are defined as follows: Memory Space BAR (not upper bits of BAR2) [0] = Mem Space Indicator (s
                # t to 0) [2:1] = Type field (10 for 64-bit, 00 for 32-bit) [3] = Prefetchable (0 or 1) [31:4] = Mask for writable bits of BAR;
                # if 32-bit BAR, set uppermost 31:n bits to 1, where 2^n=memory aperture size in bytes. If 64-bit BAR, set uppermost 63:n bits 
                # f \'7bBAR4,BAR3\'7d to 1. IO Space BAR 0] = IO Space Indicator (set to 1) [1] = Reserved (set to 0) [31:2] = Mask for writabl
                #  bits of BAR; set uppermost 31:n bits to 1, where 2^n=i/o aperture size in bytes.; EP=0xFFFF; RP=0xFFFF
                # PSU_PCIE_ATTRIB_ATTR_14_ATTR_BAR3                                               0xFFFF

                # ATTR_14
                #(OFFSET, MASK, VALUE)      (0XFD480038, 0x0000FFFFU ,0x0000FFFFU)  */
    mask_write 0XFD480038 0x0000FFFF 0x0000FFFF
                # Register : ATTR_15 @ 0XFD48003C</p>

                # For an endpoint, specifies mask/settings for Base Address Register (BAR) 4 if BAR3 is a 32-bit BAR, or the upper bits of \'7b
                # AR4,BAR3\'7d if BAR3 is the lower part of a 64-bit BAR. If BAR is not to be implemented, set to 32'h00000000. See BAR3 descri
                # tion if this functions as the upper bits of a 64-bit BAR. For a switch or root: This must be set to FFF0_FFF0. For an endpoin
                # , bits are defined as follows: Memory Space BAR (not upper bits of BAR3) [0] = Mem Space Indicator (set to 0) [2:1] = Type fi
                # ld (10 for 64-bit, 00 for 32-bit) [3] = Prefetchable (0 or 1) [31:4] = Mask for writable bits of BAR; if 32-bit BAR, set uppe
                # most 31:n bits to 1, where 2^n=memory aperture size in bytes. If 64-bit BAR, set uppermost 63:n bits of \'7bBAR5,BAR4\'7d to 
                # . IO Space BAR 0] = IO Space Indicator (set to 1) [1] = Reserved (set to 0) [31:2] = Mask for writable bits of BAR; set upper
                # ost 31:n bits to 1, where 2^n=i/o aperture size in bytes.; EP=0x0004; RP=0xFFF0
                # PSU_PCIE_ATTRIB_ATTR_15_ATTR_BAR4                                               0xFFF0

                # ATTR_15
                #(OFFSET, MASK, VALUE)      (0XFD48003C, 0x0000FFFFU ,0x0000FFF0U)  */
    mask_write 0XFD48003C 0x0000FFFF 0x0000FFF0
                # Register : ATTR_16 @ 0XFD480040</p>

                # For an endpoint, specifies mask/settings for Base Address Register (BAR) 4 if BAR3 is a 32-bit BAR, or the upper bits of \'7b
                # AR4,BAR3\'7d if BAR3 is the lower part of a 64-bit BAR. If BAR is not to be implemented, set to 32'h00000000. See BAR3 descri
                # tion if this functions as the upper bits of a 64-bit BAR. For a switch or root: This must be set to FFF0_FFF0. For an endpoin
                # , bits are defined as follows: Memory Space BAR (not upper bits of BAR3) [0] = Mem Space Indicator (set to 0) [2:1] = Type fi
                # ld (10 for 64-bit, 00 for 32-bit) [3] = Prefetchable (0 or 1) [31:4] = Mask for writable bits of BAR; if 32-bit BAR, set uppe
                # most 31:n bits to 1, where 2^n=memory aperture size in bytes. If 64-bit BAR, set uppermost 63:n bits of \'7bBAR5,BAR4\'7d to 
                # . IO Space BAR 0] = IO Space Indicator (set to 1) [1] = Reserved (set to 0) [31:2] = Mask for writable bits of BAR; set upper
                # ost 31:n bits to 1, where 2^n=i/o aperture size in bytes.; EP=0xFFF0; RP=0xFFF0
                # PSU_PCIE_ATTRIB_ATTR_16_ATTR_BAR4                                               0xFFF0

                # ATTR_16
                #(OFFSET, MASK, VALUE)      (0XFD480040, 0x0000FFFFU ,0x0000FFF0U)  */
    mask_write 0XFD480040 0x0000FFFF 0x0000FFF0
                # Register : ATTR_17 @ 0XFD480044</p>

                # For an endpoint, specifies mask/settings for Base Address Register (BAR) 5 if BAR4 is a 32-bit BAR, or the upper bits of \'7b
                # AR5,BAR4\'7d if BAR4 is the lower part of a 64-bit BAR. If BAR is not to be implemented, set to 32'h00000000. See BAR4 descri
                # tion if this functions as the upper bits of a 64-bit BAR. For a switch or root, this must be set to: 0000_0000 = Prefetchable
                # Memory Limit/Base Registers not implemented FFF0_FFF0 = 32-bit Prefetchable Memory Limit/Base implemented FFF1_FFF1 = 64-bit 
                # refetchable Memory Limit/Base implemented For an endpoint, bits are defined as follows: Memory Space BAR (not upper bits of B
                # R4) [0] = Mem Space Indicator (set to 0) [2:1] = Type field (00 for 32-bit; BAR5 cannot be lower part of a 64-bit BAR) [3] = 
                # refetchable (0 or 1) [31:4] = Mask for writable bits of BAR; set uppermost 31:n bits to 1, where 2^n=memory aperture size in 
                # ytes. IO Space BAR 0] = IO Space Indicator (set to 1) [1] = Reserved (set to 0) [31:2] = Mask for writable bits of BAR; set u
                # permost 31:n bits to 1, where 2^n=i/o aperture size in bytes.; EP=0xFFFF; RP=0xFFF1
                # PSU_PCIE_ATTRIB_ATTR_17_ATTR_BAR5                                               0xFFF1

                # ATTR_17
                #(OFFSET, MASK, VALUE)      (0XFD480044, 0x0000FFFFU ,0x0000FFF1U)  */
    mask_write 0XFD480044 0x0000FFFF 0x0000FFF1
                # Register : ATTR_18 @ 0XFD480048</p>

                # For an endpoint, specifies mask/settings for Base Address Register (BAR) 5 if BAR4 is a 32-bit BAR, or the upper bits of \'7b
                # AR5,BAR4\'7d if BAR4 is the lower part of a 64-bit BAR. If BAR is not to be implemented, set to 32'h00000000. See BAR4 descri
                # tion if this functions as the upper bits of a 64-bit BAR. For a switch or root, this must be set to: 0000_0000 = Prefetchable
                # Memory Limit/Base Registers not implemented FFF0_FFF0 = 32-bit Prefetchable Memory Limit/Base implemented FFF1_FFF1 = 64-bit 
                # refetchable Memory Limit/Base implemented For an endpoint, bits are defined as follows: Memory Space BAR (not upper bits of B
                # R4) [0] = Mem Space Indicator (set to 0) [2:1] = Type field (00 for 32-bit; BAR5 cannot be lower part of a 64-bit BAR) [3] = 
                # refetchable (0 or 1) [31:4] = Mask for writable bits of BAR; set uppermost 31:n bits to 1, where 2^n=memory aperture size in 
                # ytes. IO Space BAR 0] = IO Space Indicator (set to 1) [1] = Reserved (set to 0) [31:2] = Mask for writable bits of BAR; set u
                # permost 31:n bits to 1, where 2^n=i/o aperture size in bytes.; EP=0xFFFF; RP=0xFFF1
                # PSU_PCIE_ATTRIB_ATTR_18_ATTR_BAR5                                               0xFFF1

                # ATTR_18
                #(OFFSET, MASK, VALUE)      (0XFD480048, 0x0000FFFFU ,0x0000FFF1U)  */
    mask_write 0XFD480048 0x0000FFFF 0x0000FFF1
                # Register : ATTR_27 @ 0XFD48006C</p>

                # Specifies maximum payload supported. Valid settings are: 0- 128 bytes, 1- 256 bytes, 2- 512 bytes, 3- 1024 bytes. Transferred
                # to the Device Capabilities register. The values: 4-2048 bytes, 5- 4096 bytes are not supported; EP=0x0001; RP=0x0001
                # PSU_PCIE_ATTRIB_ATTR_27_ATTR_DEV_CAP_MAX_PAYLOAD_SUPPORTED                      1

                # Endpoint L1 Acceptable Latency. Records the latency that the endpoint can withstand on transitions from L1 state to L0 (if L1
                # state supported). Valid settings are: 0h less than 1us, 1h 1 to 2us, 2h 2 to 4us, 3h 4 to 8us, 4h 8 to 16us, 5h 16 to 32us, 6
                #  32 to 64us, 7h more than 64us. For Endpoints only. Must be 0h for other devices.; EP=0x0007; RP=0x0000
                # PSU_PCIE_ATTRIB_ATTR_27_ATTR_DEV_CAP_ENDPOINT_L1_LATENCY                        0x0

                # ATTR_27
                #(OFFSET, MASK, VALUE)      (0XFD48006C, 0x00000738U ,0x00000100U)  */
    mask_write 0XFD48006C 0x00000738 0x00000100
                # Register : ATTR_50 @ 0XFD4800C8</p>

                # Identifies the type of device/port as follows: 0000b PCI Express Endpoint device, 0001b Legacy PCI Express Endpoint device, 0
                # 00b Root Port of PCI Express Root Complex, 0101b Upstream Port of PCI Express Switch, 0110b Downstream Port of PCI Express Sw
                # tch, 0111b PCIE Express to PCI/PCI-X Bridge, 1000b PCI/PCI-X to PCI Express Bridge. Transferred to PCI Express Capabilities r
                # gister. Must be consistent with IS_SWITCH and UPSTREAM_FACING settings.; EP=0x0000; RP=0x0004
                # PSU_PCIE_ATTRIB_ATTR_50_ATTR_PCIE_CAP_DEVICE_PORT_TYPE                          4

                # PCIe Capability's Next Capability Offset pointer to the next item in the capabilities list, or 00h if this is the final capab
                # lity.; EP=0x009C; RP=0x0000
                # PSU_PCIE_ATTRIB_ATTR_50_ATTR_PCIE_CAP_NEXTPTR                                   0

                # ATTR_50
                #(OFFSET, MASK, VALUE)      (0XFD4800C8, 0x0000FFF0U ,0x00000040U)  */
    mask_write 0XFD4800C8 0x0000FFF0 0x00000040
                # Register : ATTR_105 @ 0XFD4801A4</p>

                # Number of credits that should be advertised for Completion data received on Virtual Channel 0. The bytes advertised must be l
                # ss than or equal to the bram bytes available. See VC0_RX_RAM_LIMIT; EP=0x0172; RP=0x00CD
                # PSU_PCIE_ATTRIB_ATTR_105_ATTR_VC0_TOTAL_CREDITS_CD                              0xCD

                # ATTR_105
                #(OFFSET, MASK, VALUE)      (0XFD4801A4, 0x000007FFU ,0x000000CDU)  */
    mask_write 0XFD4801A4 0x000007FF 0x000000CD
                # Register : ATTR_106 @ 0XFD4801A8</p>

                # Number of credits that should be advertised for Completion headers received on Virtual Channel 0. The sum of the posted, non 
                # osted, and completion header credits must be <= 80; EP=0x0048; RP=0x0024
                # PSU_PCIE_ATTRIB_ATTR_106_ATTR_VC0_TOTAL_CREDITS_CH                              0x24

                # Number of credits that should be advertised for Non-Posted headers received on Virtual Channel 0. The number of non posted da
                # a credits advertised by the block is equal to the number of non posted header credits. The sum of the posted, non posted, and
                # completion header credits must be <= 80; EP=0x0004; RP=0x000C
                # PSU_PCIE_ATTRIB_ATTR_106_ATTR_VC0_TOTAL_CREDITS_NPH                             0xC

                # ATTR_106
                #(OFFSET, MASK, VALUE)      (0XFD4801A8, 0x00003FFFU ,0x00000624U)  */
    mask_write 0XFD4801A8 0x00003FFF 0x00000624
                # Register : ATTR_107 @ 0XFD4801AC</p>

                # Number of credits that should be advertised for Non-Posted data received on Virtual Channel 0. The number of non posted data 
                # redits advertised by the block is equal to two times the number of non posted header credits if atomic operations are support
                # d or is equal to the number of non posted header credits if atomic operations are not supported. The bytes advertised must be
                # less than or equal to the bram bytes available. See VC0_RX_RAM_LIMIT; EP=0x0008; RP=0x0018
                # PSU_PCIE_ATTRIB_ATTR_107_ATTR_VC0_TOTAL_CREDITS_NPD                             0x18

                # ATTR_107
                #(OFFSET, MASK, VALUE)      (0XFD4801AC, 0x000007FFU ,0x00000018U)  */
    mask_write 0XFD4801AC 0x000007FF 0x00000018
                # Register : ATTR_108 @ 0XFD4801B0</p>

                # Number of credits that should be advertised for Posted data received on Virtual Channel 0. The bytes advertised must be less 
                # han or equal to the bram bytes available. See VC0_RX_RAM_LIMIT; EP=0x0020; RP=0x00B5
                # PSU_PCIE_ATTRIB_ATTR_108_ATTR_VC0_TOTAL_CREDITS_PD                              0xB5

                # ATTR_108
                #(OFFSET, MASK, VALUE)      (0XFD4801B0, 0x000007FFU ,0x000000B5U)  */
    mask_write 0XFD4801B0 0x000007FF 0x000000B5
                # Register : ATTR_109 @ 0XFD4801B4</p>

                # Not currently in use. Invert ECRC generated by block when trn_tecrc_gen_n and trn_terrfwd_n are asserted.; EP=0x0000; RP=0x00
                # 0
                # PSU_PCIE_ATTRIB_ATTR_109_ATTR_TECRC_EP_INV                                      0x0

                # Enables td bit clear and ECRC trim on received TLP's FALSE == don't trim TRUE == trim.; EP=0x0001; RP=0x0001
                # PSU_PCIE_ATTRIB_ATTR_109_ATTR_RECRC_CHK_TRIM                                    0x1

                # Enables ECRC check on received TLP's 0 == don't check 1 == always check 3 == check if enabled by ECRC check enable bit of AER
                # cap structure; EP=0x0003; RP=0x0003
                # PSU_PCIE_ATTRIB_ATTR_109_ATTR_RECRC_CHK                                         0x3

                # Index of last packet buffer used by TX TLM (i.e. number of buffers - 1). Calculated from max payload size supported and the n
                # mber of brams configured for transmit; EP=0x001C; RP=0x001C
                # PSU_PCIE_ATTRIB_ATTR_109_ATTR_VC0_TX_LASTPACKET                                 0x1c

                # Number of credits that should be advertised for Posted headers received on Virtual Channel 0. The sum of the posted, non post
                # d, and completion header credits must be <= 80; EP=0x0004; RP=0x0020
                # PSU_PCIE_ATTRIB_ATTR_109_ATTR_VC0_TOTAL_CREDITS_PH                              0x20

                # ATTR_109
                #(OFFSET, MASK, VALUE)      (0XFD4801B4, 0x0000FFFFU ,0x00007E20U)  */
    mask_write 0XFD4801B4 0x0000FFFF 0x00007E20
                # Register : ATTR_34 @ 0XFD480088</p>

                # Specifies values to be transferred to Header Type register. Bit 7 should be set to '0' indicating single-function device. Bit
                # 0 identifies header as Type 0 or Type 1, with '0' indicating a Type 0 header.; EP=0x0000; RP=0x0001
                # PSU_PCIE_ATTRIB_ATTR_34_ATTR_HEADER_TYPE                                        0x1

                # ATTR_34
                #(OFFSET, MASK, VALUE)      (0XFD480088, 0x000000FFU ,0x00000001U)  */
    mask_write 0XFD480088 0x000000FF 0x00000001
                # Register : ATTR_53 @ 0XFD4800D4</p>

                # PM Capability's Next Capability Offset pointer to the next item in the capabilities list, or 00h if this is the final capabil
                # ty.; EP=0x0048; RP=0x0060
                # PSU_PCIE_ATTRIB_ATTR_53_ATTR_PM_CAP_NEXTPTR                                     0x60

                # ATTR_53
                #(OFFSET, MASK, VALUE)      (0XFD4800D4, 0x000000FFU ,0x00000060U)  */
    mask_write 0XFD4800D4 0x000000FF 0x00000060
                # Register : ATTR_41 @ 0XFD4800A4</p>

                # MSI Per-Vector Masking Capable. The value is transferred to the MSI Control Register[8]. When set, adds Mask and Pending Dwor
                #  to Cap structure; EP=0x0000; RP=0x0000
                # PSU_PCIE_ATTRIB_ATTR_41_ATTR_MSI_CAP_PER_VECTOR_MASKING_CAPABLE                 0x0

                # Indicates that the MSI structures exists. If this is FALSE, then the MSI structure cannot be accessed via either the link or 
                # he management port.; EP=0x0001; RP=0x0000
                # PSU_PCIE_ATTRIB_ATTR_41_ATTR_MSI_CAP_ON                                         0

                # MSI Capability's Next Capability Offset pointer to the next item in the capabilities list, or 00h if this is the final capabi
                # ity.; EP=0x0060; RP=0x0000
                # PSU_PCIE_ATTRIB_ATTR_41_ATTR_MSI_CAP_NEXTPTR                                    0x0

                # Indicates that the MSI structures exists. If this is FALSE, then the MSI structure cannot be accessed via either the link or 
                # he management port.; EP=0x0001; RP=0x0000
                # PSU_PCIE_ATTRIB_ATTR_41_ATTR_MSI_CAP_ON                                         0

                # ATTR_41
                #(OFFSET, MASK, VALUE)      (0XFD4800A4, 0x000003FFU ,0x00000000U)  */
    mask_write 0XFD4800A4 0x000003FF 0x00000000
                # Register : ATTR_97 @ 0XFD480184</p>

                # Maximum Link Width. Valid settings are: 000001b x1, 000010b x2, 000100b x4, 001000b x8.; EP=0x0004; RP=0x0004
                # PSU_PCIE_ATTRIB_ATTR_97_ATTR_LINK_CAP_MAX_LINK_WIDTH                            0x1

                # Used by LTSSM to set Maximum Link Width. Valid settings are: 000001b [x1], 000010b [x2], 000100b [x4], 001000b [x8].; EP=0x00
                # 4; RP=0x0004
                # PSU_PCIE_ATTRIB_ATTR_97_ATTR_LTSSM_MAX_LINK_WIDTH                               0x1

                # ATTR_97
                #(OFFSET, MASK, VALUE)      (0XFD480184, 0x00000FFFU ,0x00000041U)  */
    mask_write 0XFD480184 0x00000FFF 0x00000041
                # Register : ATTR_100 @ 0XFD480190</p>

                # TRUE specifies upstream-facing port. FALSE specifies downstream-facing port.; EP=0x0001; RP=0x0000
                # PSU_PCIE_ATTRIB_ATTR_100_ATTR_UPSTREAM_FACING                                   0x0

                # ATTR_100
                #(OFFSET, MASK, VALUE)      (0XFD480190, 0x00000040U ,0x00000000U)  */
    mask_write 0XFD480190 0x00000040 0x00000000
                # Register : ATTR_101 @ 0XFD480194</p>

                # Enable the routing of message TLPs to the user through the TRN RX interface. A bit value of 1 enables routing of the message 
                # LP to the user. Messages are always decoded by the message decoder. Bit 0 - ERR COR, Bit 1 - ERR NONFATAL, Bit 2 - ERR FATAL,
                # Bit 3 - INTA Bit 4 - INTB, Bit 5 - INTC, Bit 6 - INTD, Bit 7 PM_PME, Bit 8 - PME_TO_ACK, Bit 9 - unlock, Bit 10 PME_Turn_Off;
                # EP=0x0000; RP=0x07FF
                # PSU_PCIE_ATTRIB_ATTR_101_ATTR_ENABLE_MSG_ROUTE                                  0x7FF

                # Disable BAR filtering. Does not change the behavior of the bar hit outputs; EP=0x0000; RP=0x0001
                # PSU_PCIE_ATTRIB_ATTR_101_ATTR_DISABLE_BAR_FILTERING                             0x1

                # ATTR_101
                #(OFFSET, MASK, VALUE)      (0XFD480194, 0x0000FFE2U ,0x0000FFE2U)  */
    mask_write 0XFD480194 0x0000FFE2 0x0000FFE2
                # Register : ATTR_37 @ 0XFD480094</p>

                # Link Bandwidth notification capability. Indicates support for the link bandwidth notification status and interrupt mechanism.
                # Required for Root.; EP=0x0000; RP=0x0001
                # PSU_PCIE_ATTRIB_ATTR_37_ATTR_LINK_CAP_LINK_BANDWIDTH_NOTIFICATION_CAP           0x1

                # ATTR_37
                #(OFFSET, MASK, VALUE)      (0XFD480094, 0x00000200U ,0x00000200U)  */
    mask_write 0XFD480094 0x00000200 0x00000200
                # Register : ATTR_93 @ 0XFD480174</p>

                # Enables the Replay Timer to use the user-defined LL_REPLAY_TIMEOUT value (or combined with the built-in value, depending on L
                # _REPLAY_TIMEOUT_FUNC). If FALSE, the built-in value is used.; EP=0x0000; RP=0x0000
                # PSU_PCIE_ATTRIB_ATTR_93_ATTR_LL_REPLAY_TIMEOUT_EN                               0x1

                # Sets a user-defined timeout for the Replay Timer to force cause the retransmission of unacknowledged TLPs; refer to LL_REPLAY
                # TIMEOUT_EN and LL_REPLAY_TIMEOUT_FUNC to see how this value is used. The unit for this attribute is in symbol times, which is
                # 4ns at GEN1 speeds and 2ns at GEN2.; EP=0x0000; RP=0x0000
                # PSU_PCIE_ATTRIB_ATTR_93_ATTR_LL_REPLAY_TIMEOUT                                  0x1000

                # ATTR_93
                #(OFFSET, MASK, VALUE)      (0XFD480174, 0x0000FFFFU ,0x00009000U)  */
    mask_write 0XFD480174 0x0000FFFF 0x00009000
                # Register : ID @ 0XFD480200</p>

                # Device ID for the the PCIe Cap Structure Device ID field
                # PSU_PCIE_ATTRIB_ID_CFG_DEV_ID                                                   0xd021

                # Vendor ID for the PCIe Cap Structure Vendor ID field
                # PSU_PCIE_ATTRIB_ID_CFG_VEND_ID                                                  0x10ee

                # ID
                #(OFFSET, MASK, VALUE)      (0XFD480200, 0xFFFFFFFFU ,0x10EED021U)  */
    mask_write 0XFD480200 0xFFFFFFFF 0x10EED021
                # Register : SUBSYS_ID @ 0XFD480204</p>

                # Subsystem ID for the the PCIe Cap Structure Subsystem ID field
                # PSU_PCIE_ATTRIB_SUBSYS_ID_CFG_SUBSYS_ID                                         0x7

                # Subsystem Vendor ID for the PCIe Cap Structure Subsystem Vendor ID field
                # PSU_PCIE_ATTRIB_SUBSYS_ID_CFG_SUBSYS_VEND_ID                                    0x10ee

                # SUBSYS_ID
                #(OFFSET, MASK, VALUE)      (0XFD480204, 0xFFFFFFFFU ,0x10EE0007U)  */
    mask_write 0XFD480204 0xFFFFFFFF 0x10EE0007
                # Register : REV_ID @ 0XFD480208</p>

                # Revision ID for the the PCIe Cap Structure
                # PSU_PCIE_ATTRIB_REV_ID_CFG_REV_ID                                               0x0

                # REV_ID
                #(OFFSET, MASK, VALUE)      (0XFD480208, 0x000000FFU ,0x00000000U)  */
    mask_write 0XFD480208 0x000000FF 0x00000000
                # Register : ATTR_24 @ 0XFD480060</p>

                # Code identifying basic function, subclass and applicable programming interface. Transferred to the Class Code register.; EP=0
                # 8000; RP=0x8000
                # PSU_PCIE_ATTRIB_ATTR_24_ATTR_CLASS_CODE                                         0x400

                # ATTR_24
                #(OFFSET, MASK, VALUE)      (0XFD480060, 0x0000FFFFU ,0x00000400U)  */
    mask_write 0XFD480060 0x0000FFFF 0x00000400
                # Register : ATTR_25 @ 0XFD480064</p>

                # Code identifying basic function, subclass and applicable programming interface. Transferred to the Class Code register.; EP=0
                # 0005; RP=0x0006
                # PSU_PCIE_ATTRIB_ATTR_25_ATTR_CLASS_CODE                                         0x6

                # INTX Interrupt Generation Capable. If FALSE, this will cause Command[10] to be hardwired to 0.; EP=0x0001; RP=0x0001
                # PSU_PCIE_ATTRIB_ATTR_25_ATTR_CMD_INTX_IMPLEMENTED                               0

                # ATTR_25
                #(OFFSET, MASK, VALUE)      (0XFD480064, 0x000001FFU ,0x00000006U)  */
    mask_write 0XFD480064 0x000001FF 0x00000006
                # Register : ATTR_4 @ 0XFD480010</p>

                # Indicates that the AER structures exists. If this is FALSE, then the AER structure cannot be accessed via either the link or 
                # he management port, and AER will be considered to not be present for error management tasks (such as what types of error mess
                # ges are sent if an error is detected).; EP=0x0001; RP=0x0001
                # PSU_PCIE_ATTRIB_ATTR_4_ATTR_AER_CAP_ON                                          0

                # Indicates that the AER structures exists. If this is FALSE, then the AER structure cannot be accessed via either the link or 
                # he management port, and AER will be considered to not be present for error management tasks (such as what types of error mess
                # ges are sent if an error is detected).; EP=0x0001; RP=0x0001
                # PSU_PCIE_ATTRIB_ATTR_4_ATTR_AER_CAP_ON                                          0

                # ATTR_4
                #(OFFSET, MASK, VALUE)      (0XFD480010, 0x00001000U ,0x00000000U)  */
    mask_write 0XFD480010 0x00001000 0x00000000
                # Register : ATTR_89 @ 0XFD480164</p>

                # VSEC's Next Capability Offset pointer to the next item in the capabilities list, or 000h if this is the final capability.; EP
                # 0x0140; RP=0x0140
                # PSU_PCIE_ATTRIB_ATTR_89_ATTR_VSEC_CAP_NEXTPTR                                   0

                # ATTR_89
                #(OFFSET, MASK, VALUE)      (0XFD480164, 0x00001FFEU ,0x00000000U)  */
    mask_write 0XFD480164 0x00001FFE 0x00000000
                # Register : ATTR_79 @ 0XFD48013C</p>

                # CRS SW Visibility. Indicates RC can return CRS to SW. Transferred to the Root Capabilities register.; EP=0x0000; RP=0x0000
                # PSU_PCIE_ATTRIB_ATTR_79_ATTR_ROOT_CAP_CRS_SW_VISIBILITY                         1

                # ATTR_79
                #(OFFSET, MASK, VALUE)      (0XFD48013C, 0x00000020U ,0x00000020U)  */
    mask_write 0XFD48013C 0x00000020 0x00000020
                # Register : ATTR_43 @ 0XFD4800AC</p>

                # Indicates that the MSIX structures exists. If this is FALSE, then the MSIX structure cannot be accessed via either the link o
                #  the management port.; EP=0x0001; RP=0x0000
                # PSU_PCIE_ATTRIB_ATTR_43_ATTR_MSIX_CAP_ON                                        0

                # ATTR_43
                #(OFFSET, MASK, VALUE)      (0XFD4800AC, 0x00000100U ,0x00000000U)  */
    mask_write 0XFD4800AC 0x00000100 0x00000000
}

set psu_resetin_init_data {
                # : PUTTING SERDES PERIPHERAL IN RESET
                # : PUTTING USB0 IN RESET
                # Register : RST_LPD_TOP @ 0XFF5E023C</p>

                # USB 0 reset for control registers
                # PSU_CRL_APB_RST_LPD_TOP_USB0_APB_RESET                                          0X1

                # USB 0 sleep circuit reset
                # PSU_CRL_APB_RST_LPD_TOP_USB0_HIBERRESET                                         0X1

                # USB 0 reset
                # PSU_CRL_APB_RST_LPD_TOP_USB0_CORERESET                                          0X1

                # Software control register for the LPD block.
                #(OFFSET, MASK, VALUE)      (0XFF5E023C, 0x00000540U ,0x00000540U)  */
    mask_write 0XFF5E023C 0x00000540 0x00000540
                # : PUTTING GEM0 IN RESET
                # Register : RST_LPD_IOU0 @ 0XFF5E0230</p>

                # GEM 3 reset
                # PSU_CRL_APB_RST_LPD_IOU0_GEM3_RESET                                             0X1

                # Software controlled reset for the GEMs
                #(OFFSET, MASK, VALUE)      (0XFF5E0230, 0x00000008U ,0x00000008U)  */
    mask_write 0XFF5E0230 0x00000008 0x00000008
                # : PUTTING SATA IN RESET
                # Register : RST_FPD_TOP @ 0XFD1A0100</p>

                # Sata block level reset
                # PSU_CRF_APB_RST_FPD_TOP_SATA_RESET                                              0X1

                # FPD Block level software controlled reset
                #(OFFSET, MASK, VALUE)      (0XFD1A0100, 0x00000002U ,0x00000002U)  */
    mask_write 0XFD1A0100 0x00000002 0x00000002
                # : PUTTING PCIE IN RESET
                # Register : RST_FPD_TOP @ 0XFD1A0100</p>

                # PCIE config reset
                # PSU_CRF_APB_RST_FPD_TOP_PCIE_CFG_RESET                                          0X1

                # PCIE control block level reset
                # PSU_CRF_APB_RST_FPD_TOP_PCIE_CTRL_RESET                                         0X1

                # PCIE bridge block level reset (AXI interface)
                # PSU_CRF_APB_RST_FPD_TOP_PCIE_BRIDGE_RESET                                       0X1

                # FPD Block level software controlled reset
                #(OFFSET, MASK, VALUE)      (0XFD1A0100, 0x000E0000U ,0x000E0000U)  */
    mask_write 0XFD1A0100 0x000E0000 0x000E0000
                # : PUTTING DP IN RESET
                # Register : DP_TX_PHY_POWER_DOWN @ 0XFD4A0238</p>

                # Two bits per lane. When set to 11, moves the GT to power down mode. When set to 00, GT will be in active state. bits [1:0] - 
                # ane0 Bits [3:2] - lane 1
                # PSU_DP_DP_TX_PHY_POWER_DOWN_POWER_DWN                                           0XA

                # Control PHY Power down
                #(OFFSET, MASK, VALUE)      (0XFD4A0238, 0x0000000FU ,0x0000000AU)  */
    mask_write 0XFD4A0238 0x0000000F 0x0000000A
                # Register : DP_PHY_RESET @ 0XFD4A0200</p>

                # Set to '1' to hold the GT in reset. Clear to release.
                # PSU_DP_DP_PHY_RESET_GT_RESET                                                    0X1

                # Reset the transmitter PHY.
                #(OFFSET, MASK, VALUE)      (0XFD4A0200, 0x00000002U ,0x00000002U)  */
    mask_write 0XFD4A0200 0x00000002 0x00000002
                # Register : RST_FPD_TOP @ 0XFD1A0100</p>

                # Display Port block level reset (includes DPDMA)
                # PSU_CRF_APB_RST_FPD_TOP_DP_RESET                                                0X1

                # FPD Block level software controlled reset
                #(OFFSET, MASK, VALUE)      (0XFD1A0100, 0x00010000U ,0x00010000U)  */
    mask_write 0XFD1A0100 0x00010000 0x00010000
}

set psu_ps_pl_isolation_removal_data {
                # : PS-PL POWER UP REQUEST
                # Register : REQ_PWRUP_INT_EN @ 0XFFD80118</p>

                # Power-up Request Interrupt Enable for PL
                # PSU_PMU_GLOBAL_REQ_PWRUP_INT_EN_PL                                              1

                # Power-up Request Interrupt Enable Register. Writing a 1 to this location will unmask the interrupt.
                #(OFFSET, MASK, VALUE)      (0XFFD80118, 0x00800000U ,0x00800000U)  */
    mask_write 0XFFD80118 0x00800000 0x00800000
                # Register : REQ_PWRUP_TRIG @ 0XFFD80120</p>

                # Power-up Request Trigger for PL
                # PSU_PMU_GLOBAL_REQ_PWRUP_TRIG_PL                                                1

                # Power-up Request Trigger Register. A write of one to this location will generate a power-up request to the PMU.
                #(OFFSET, MASK, VALUE)      (0XFFD80120, 0x00800000U ,0x00800000U)  */
    mask_write 0XFFD80120 0x00800000 0x00800000
                # : POLL ON PL POWER STATUS
                # Register : REQ_PWRUP_STATUS @ 0XFFD80110</p>

                # Power-up Request Status for PL
                # PSU_PMU_GLOBAL_REQ_PWRUP_STATUS_PL                                              1
    mask_poll 0XFFD80110 0x00800000 0x00000000
}

set psu_ps_pl_reset_config_data {
                # : PS PL RESET SEQUENCE
                # : FABRIC RESET USING EMIO
                # Register : MASK_DATA_5_MSW @ 0XFF0A002C</p>

                # Operation is the same as MASK_DATA_0_LSW[MASK_0_LSW]
                # PSU_GPIO_MASK_DATA_5_MSW_MASK_5_MSW                                             0x8000

                # Maskable Output Data (GPIO Bank5, EMIO, Upper 16bits)
                #(OFFSET, MASK, VALUE)      (0XFF0A002C, 0xFFFF0000U ,0x80000000U)  */
    mask_write 0XFF0A002C 0xFFFF0000 0x80000000
                # Register : DIRM_5 @ 0XFF0A0344</p>

                # Operation is the same as DIRM_0[DIRECTION_0]
                # PSU_GPIO_DIRM_5_DIRECTION_5                                                     0x80000000

                # Direction mode (GPIO Bank5, EMIO)
                #(OFFSET, MASK, VALUE)      (0XFF0A0344, 0xFFFFFFFFU ,0x80000000U)  */
    mask_write 0XFF0A0344 0xFFFFFFFF 0x80000000
                # Register : OEN_5 @ 0XFF0A0348</p>

                # Operation is the same as OEN_0[OP_ENABLE_0]
                # PSU_GPIO_OEN_5_OP_ENABLE_5                                                      0x80000000

                # Output enable (GPIO Bank5, EMIO)
                #(OFFSET, MASK, VALUE)      (0XFF0A0348, 0xFFFFFFFFU ,0x80000000U)  */
    mask_write 0XFF0A0348 0xFFFFFFFF 0x80000000
                # Register : DATA_5 @ 0XFF0A0054</p>

                # Output Data
                # PSU_GPIO_DATA_5_DATA_5                                                          0x80000000

                # Output Data (GPIO Bank5, EMIO)
                #(OFFSET, MASK, VALUE)      (0XFF0A0054, 0xFFFFFFFFU ,0x80000000U)  */
    mask_write 0XFF0A0054 0xFFFFFFFF 0x80000000
    mask_delay 0x00000000 1
                # : FABRIC RESET USING DATA_5 TOGGLE
                # Register : DATA_5 @ 0XFF0A0054</p>

                # Output Data
                # PSU_GPIO_DATA_5_DATA_5                                                          0X00000000

                # Output Data (GPIO Bank5, EMIO)
                #(OFFSET, MASK, VALUE)      (0XFF0A0054, 0xFFFFFFFFU ,0x00000000U)  */
    mask_write 0XFF0A0054 0xFFFFFFFF 0x00000000
    mask_delay 0x00000000 1
                # : FABRIC RESET USING DATA_5 TOGGLE
                # Register : DATA_5 @ 0XFF0A0054</p>

                # Output Data
                # PSU_GPIO_DATA_5_DATA_5                                                          0x80000000

                # Output Data (GPIO Bank5, EMIO)
                #(OFFSET, MASK, VALUE)      (0XFF0A0054, 0xFFFFFFFFU ,0x80000000U)  */
    mask_write 0XFF0A0054 0xFFFFFFFF 0x80000000
}

proc psu_init {} {
    # save current mode
    set saved_mode [configparams force-mem-accesses]                  
    # force accesses
    configparams force-mem-accesses 1 
    variable psu_mio_init_data 
    variable psu_pll_init_data 
    variable psu_clock_init_data
        variable psu_ddr_init_data
    variable psu_peripherals_init_data
    variable psu_resetin_init_data
    variable psu_resetout_init_data
    variable psu_serdes_init_data
    variable psu_resetin_init_data
    variable psu_peripherals_powerdwn_data 

    init_ps [subst {$psu_mio_init_data $psu_pll_init_data $psu_clock_init_data $psu_ddr_init_data }]
    psu_ddr_phybringup_data 
    init_ps [subst {$psu_peripherals_init_data $psu_resetin_init_data }]
    init_serdes 
    init_ps [subst {$psu_serdes_init_data $psu_resetout_init_data }]
    init_peripheral 
    init_ps [subst {$psu_peripherals_powerdwn_data }]
    # restore original mode
    configparams force-mem-accesses $saved_mode                                       
}

proc psu_post_config {} {
    variable psu_post_config_data
    init_ps [subst {$psu_post_config_data}]
}

proc psu_ps_pl_reset_config {} {
    variable psu_ps_pl_reset_config_data
    init_ps [subst {$psu_ps_pl_reset_config_data}]
}

proc psu_ps_pl_isolation_removal {} {
    variable psu_ps_pl_isolation_removal_data
    init_ps [subst {$psu_ps_pl_isolation_removal_data}]
}


proc mask_read { addr mask } {
    set curval "0x[string range [mrd -force $addr] end-8 end]"
    set maskedval [expr {$curval & $mask}]
    return $maskedval
}


proc mask_poll { addr mask } {
    set count 1
    set curval "0x[string range [mrd -force $addr] end-8 end]"
    set maskedval [expr {$curval & $mask}]
    while { $maskedval == 0 } {
        set curval "0x[string range [mrd -force $addr] end-8 end]"
        set maskedval [expr {$curval & $mask}]
        set count [ expr { $count + 1 } ]
        if { $count == 100000000 } {
          puts "Timeout Reached. Mask poll failed at ADDRESS: $addr MASK: $mask"
          break
        }
    }
}

proc psu_mask_write { addr mask value } {
    set curval "0x[string range [mrd -force $addr] end-8 end]"
    set curval [expr {$curval & ~($mask)}]
    set maskedval [expr {$value & $mask}]
    set maskedval [expr {$curval | $maskedval}]
    mwr -force $addr $maskedval
}


proc  serdes_fixcal_code {} {
   #/*
   # * L3_TM_CALIB_DIG19
   # */
   mask_write 0xFD40EC4C 0xFFFFFFFF 0x00000020
   
   
   #/*
   # * ICM_CFG0
   # */
   mask_write 0xFD410010 0xFFFFFFFF 0x00000001

   
   #/*
   # * is calibration done, polling on L3_CALIB_DONE_STATUS
   # */
   mask_poll 0xFD40EF14 0x2
 
   #unsigned int tmp_0_1; 
   set tmp_0_1 [mrd -force -value 0xFD400B0C]
   set tmp_0_1 [expr {$tmp_0_1 & 0x3F}]

   set tmp_0_2 [expr {$tmp_0_1 & 0x7}]
   set tmp_0_3 [expr {$tmp_0_1 & 0x38}]
   
   #Configure ICM for de-asserting CMN_Resetn
   mask_write 0xFD410010 0xFFFFFFFF 0x00000000
   mask_write 0xFD410014 0xFFFFFFFF 0x00000000

   set tmp_0_2_mod [expr {($tmp_0_2 << 1) | (0x1)}]
   set tmp_0_2_mod [expr {$tmp_0_2_mod << 4}]
   
   set tmp_0_3 [expr {$tmp_0_3 >> 3}]
   mask_write 0xFD40EC4C 0xFFFFFFFF $tmp_0_3
   
   #L3_TM_CALIB_DIG18
   mask_write 0xFD40EC48 0xFFFFFFFF $tmp_0_2_mod


}

proc serdes_enb_coarse_saturation {} { 
   #/* 
   # * Enable PLL Coarse Code saturation Logic
   # */
   mask_write 0xFD402094 0xFFFFFFFF 0x00000010 
   mask_write 0xFD406094 0xFFFFFFFF 0x00000010 
   mask_write 0xFD40A094 0xFFFFFFFF 0x00000010 
   mask_write 0xFD40E094 0xFFFFFFFF 0x00000010

}


proc init_serdes {} {

  serdes_fixcal_code
  serdes_enb_coarse_saturation

}

proc poll { addr mask data} {
    set curval "0x[string range [mrd -force $addr] end-8 end]"
    set maskedval [expr {$curval & $mask}]
    while { $maskedval != $data } {
        set curval "0x[string range [mrd -force $addr] end-8 end]"
        set maskedval [expr {$curval & $mask}]
    }
}

proc init_peripheral {} {

        # Release all resets in the IOU */
   mask_write 0xFF5E0230 0xFFFFFFFF 0x00000000
   mask_write 0xFF5E0234 0xFFFFFFFF 0x00000000
   mask_write 0xFF5E0238 0xFFFFFFFF 0x00000000 

        # Take LPD out of reset except R5 */
   set tmp_0_1 [mrd -force -value 0xFF5E023C]
   set tmp_0_1 [expr {$tmp_0_1 & 0x7}]
   mask_write 0xFF5E023C 0xFFFFFFFF $tmp_0_1

        # Take most of FPD out of reset */
   mask_write 0XFD1A0100 0xFFFFFFFF 0x00000000 

        # Making DPDMA as secure 
   mask_write 0xFD690040 0x00000001 0x00000000 
        # Making PCIe as secure 
   mask_write 0xFD690030 0x00000001 0x00000000 

}


proc psu_ddr_phybringup_data {} {
mwr -force  0xFD090000 0x0000A845
mwr -force  0xFD090004 0x003FFFFF
mwr -force  0xFD09000C 0x00000010
mwr -force  0xFD090010 0x00000010

poll 0xFD080030 0x0000000F 0x0000000F  
        psu_mask_write 0xFD080004 0x00000001 0x00000001
#poll for PHY initialization to complete 
poll 0xFD080030 0x000000FF 0x0000001F 

mwr -force  0xFD0701B0 0x00000001
mwr -force  0xFD070320 0x00000001
#//poll for DDR initialization to complete 
poll 0xFD070004 0x0000000F 0x00000001 

        psu_mask_write 0xFD080014 0x00000040 0x00000040
#Dummy reads before PHY training starts
mrd -force 0xFD070004    
  #//dummy reads 
mrd -force 0xFD070004    
  #//dummy reads 
mrd -force 0xFD070004    
  #//dummy reads 
mrd -force 0xFD070004    
  #//dummy reads 
mrd -force 0xFD070004    
  #//dummy reads 
mrd -force 0xFD070004    
  #//dummy reads 
psu_mask_write 0xFD080004 0xFFFFFFFF 0x0004FE01
 #trigger PHY training 
poll 0xFD080030 0x00000FFF 0x00000FFF
 
  #Poll PUB_PGSR0 for Trng complete  


 # Run Vref training in static read mode  
mwr -force  0xFD080200 0x110011C7
mwr -force  0xFD080018 0x00F01EF2
mwr -force  0xFD08001C 0x55AA0098
mwr -force  0xFD08142C 0x00001830
mwr -force  0xFD08146C 0x00001830
mwr -force  0xFD0814AC 0x00001830
mwr -force  0xFD0814EC 0x00001830
mwr -force  0xFD08152C 0x00001830
psu_mask_write 0xFD080004 0xFFFFFFFF 0x00060001
  
 #trigger VreFPHY training 
poll 0xFD080030 0x00004001 0x00004001
     
 #//Poll PUB_PGSR0 for Trng complete  
 # Vref training is complete, disabling static read mode 
mwr -force  0xFD080200 0x810011C7
mwr -force  0xFD080018 0x00F12302
mwr -force  0xFD08001C 0x55AA0080
mwr -force  0xFD08142C 0x00001800
mwr -force  0xFD08146C 0x00001800
mwr -force  0xFD0814AC 0x00001800
mwr -force  0xFD0814EC 0x00001800
mwr -force  0xFD08152C 0x00001800
mwr -force  0xFD070180 0x01000040
mwr -force  0xFD070060 0x00000000
        psu_mask_write 0xFD080014 0x00000040 0x00000000

 
}