4 * \brief SAM4E-EK board configuration.
\r
6 * Copyright (c) 2012-2013 Atmel Corporation. All rights reserved.
\r
12 * Redistribution and use in source and binary forms, with or without
\r
13 * modification, are permitted provided that the following conditions are met:
\r
15 * 1. Redistributions of source code must retain the above copyright notice,
\r
16 * this list of conditions and the following disclaimer.
\r
18 * 2. Redistributions in binary form must reproduce the above copyright notice,
\r
19 * this list of conditions and the following disclaimer in the documentation
\r
20 * and/or other materials provided with the distribution.
\r
22 * 3. The name of Atmel may not be used to endorse or promote products derived
\r
23 * from this software without specific prior written permission.
\r
25 * 4. This software may only be redistributed and used in connection with an
\r
26 * Atmel microcontroller product.
\r
28 * THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
\r
29 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
\r
30 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
\r
31 * EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
\r
32 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
\r
33 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
\r
34 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
\r
35 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
\r
36 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
\r
37 * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
\r
38 * POSSIBILITY OF SUCH DAMAGE.
\r
44 #ifndef CONF_BOARD_H_INCLUDED
\r
45 #define CONF_BOARD_H_INCLUDED
\r
47 /* Configure UART pins */
\r
48 //#define CONF_BOARD_UART_CONSOLE
\r
50 /* Enable ETH PHY: KSZ8051MNL feature */
\r
51 #define CONF_BOARD_KSZ8051MNL
\r
53 /** Configure LCD EBI pins */
\r
54 #define CONF_BOARD_ILI93XX
\r
56 /** Configure Backlight control pin */
\r
57 #define CONF_BOARD_AAT3155
\r
60 * LED pins are not configured for PWM function here.
\r
61 * Because those LED pins are enabled for PIO function by default.
\r
62 * You can enable them according to application.
\r
64 /* Configure PWM LED0 pin */
\r
65 //#define CONF_BOARD_PWM_LED0
\r
67 /* Configure PWM LED1 pin */
\r
68 //#define CONF_BOARD_PWM_LED1
\r
70 /* Configure PWM LED2 pin */
\r
71 //#define CONF_BOARD_PWM_LED2
\r
73 /* Configure PWM LED3 pin */
\r
74 //#define CONF_BOARD_PWM_LED3
\r
77 * USART pins are configured as basic serial port by default.
\r
78 * You can enable other pins according application.
\r
80 /* Configure USART RXD pin */
\r
81 //#define CONF_BOARD_USART_RXD
\r
83 /* Configure USART TXD pin */
\r
84 //#define CONF_BOARD_USART_TXD
\r
86 /* Configure USART CTS pin */
\r
87 //#define CONF_BOARD_USART_CTS
\r
89 /* Configure USART RTS pin */
\r
90 //#define CONF_BOARD_USART_RTS
\r
92 /* Configure USART synchronous communication SCK pin */
\r
93 //#define CONF_BOARD_USART_SCK
\r
95 /* Configure ADM3312 enable pin */
\r
96 //#define CONF_BOARD_ADM3312_EN
\r
97 //#define CONF_BOARD_ADM3312_EN_DISABLE_AT_INIT
\r
99 #endif /* CONF_BOARD_H_INCLUDED */
\r