source archive release.
JTAG Layer:
- * New CMSIS-DAP driver
- * Andes AICE debug adapter support
- * New OpenJTAG driver
- * New BCM2835 (RaspberryPi) driver
- * JTAG VPI client driver (for OpenRISC Reference Platform SoC)
- * Xilinx BSCAN_* for OpenRISC support
- * ST-LINKv2-1 support
- * ST-LINKv2 SWO tracing support (UART emulation)
- * JLink-OB (onboard) support
- * Altera USB Blaster driver rewrite, initial Blaster II
- support
- * ULINK driver ported to libusb-1.0, OpenULINK build fixes
- * Support up to 64 bit IR lengths
- * SVF playback (FPGA programming) fixes
- * "ftdi" interface driver got extensive testing and is now
- recommended over the old ft2232 implementation
+ * New driver for J-Link adapters based on libjaylink
+ (including support for FPGA configuration and EMUCOM)
+ * FTDI improvements to work at 30MHz clock
+ * BCM2835 native driver SWD and Raspberry Pi2 support
+ * BCM2835 is set to 4ma drive, slow slew rate
+ * ixo-usb-jtag (emulation of an Altera Bus Blaster I on
+ Cypress FX2 IC) support
+ * JTAG pass-through mode for CMSIS-DAP (including support for
+ FPGA configuration)
+ * OpenJTAG support for Cypress CY7C65215
+ * connect_assert_srst support for SWD
+ * Xilinx Virtex-II Series7 bitstream loading support
+ * Use JEP106 data to decode IDs
+ * Deprecated "ft2232" driver removed (use "ftdi" instead)
+ * GPL-incompatible FTDI D2XX library support dropped (Presto,
+ OpenJTAG and USB-Blaster I are using libftdi only now)
+ * ZY1000 support dropped (unmaintained since long)
+ * oocd_trace support dropped
Boundary Scan:
Target Layer:
- * New target: Andes nds32
- * New target: OpenRISC OR1K
- * New target: Intel Quark X10xx
- * MIPS EJTAG 1.5/2.0 support
- * MIPS speed improvements
- * Cortex-M, Cortex-A (MEM-AP, APB-AP) targets working with BE
- hosts now
- * XScale vector_catch support, reset fixes
- * dsp563xx ad-hoc breakpoint/watchpoint support
- * RTOS support for embKernel
- * Target profiling improvements
- * Memory access functions testbench
+ * ARMv7-A, Cortex-M, Cortex-A/R important fixes and
+ improvements (allowing e.g. simultaneous debugging of A8 and
+ M3 cores, JTAG WAIT support etc.)
+ * ARM Cortex-A,R allow interrupt disable during single-step
+ (maskisr command)
+ * Semihosting support for ARMv7-A
+ * ARM Cortex-M7 support
+ * Intel Quark mcu D2000 support
+ * Freescale LS102x SAP support
+ * ThreadX RTOS support on ARM926E-JS
+ * Cortex-M RTOS stack alignment fixes
+ * FreeRTOS FPU support
+ * uC/OS-III RTOS support
+ * bridging semihosting to GDB's File-I/O support
+ * -defer-examine option added to target create command
+ * verify_image_checksum command added
Flash Layer:
- * STM32 family sync with reference manuals, other bugfixes
- * STM32F401, STM32F07x support
- * Atmel SAM4L, SAMG5x support
- * at91sam3sd8{a,b}, at91sam3s8{a,b,c}, at91sam4s,
- at91sam3n0{a,b,0a,0b} support, bugfixes
- * Atmel SAMD support
- * Milandr 1986ВЕ* support
- * Kinetis KL, K21 support
- * Nuvoton NuMicro MINI5{1,2,4} support
- * Nuvoton NUC910 series support
- * NXP LPC43xx, LPC2000 fixes
- * NXP LPC800, LPC810 support
- * More ATmega parts supported
- * Fujitsu MB9Ax family support
- * EFM32 Wonder Gecko family support
- * Nordic nRF51 support
+ * Atmel SAM4S, SAM4N, SAM4C support
+ * Atmel SAMV, SAMS, SAME (Cortex-M7) support
+ * Atmel AT91SAMD handle reset run/halt in DSU, other fixes
+ * Atmel AT91SAML21, SAML22, SAMC20/SAMC21, SAMD09 support
+ * ST STM32F4x support
+ * ST STM32F74x/76x/77x, STM32L4 support
+ * ST STM32L0 categories 1, 2 and 5 support
+ * Kinetis K02, K21, K22, K24, K26, K63, K64, K66 support
+ * Kinetis KE, KVx, K8x families support
+ * Kinetis FlexNVM handling
+ * Kinetis flash protection, security, mass_erase improvements
+ * Infineon XMC4xxx family support
+ * Infineon XMC1000 flash driver
+ * Energy Micro EFM32 Happy Gecko support
+ * Energy Micro EFM32 debug interface lock support
+ * Analog Devices ADuCM360 support
+ * Unified Nuvoton NuMicro flash driver
+ * NIIET K1921VK01T (Cortex-M4) support
+ * Nordic Semiconductor nRF51 improvements
+ * Spansion FM4 flash (including MB9BFx64/x65, S6E2DH) driver
+ * Ambiq Micro Apollo flash driver
+ * PIC32MX new device IDs, 17x/27x flash support
+ * read_bank() and verify_bank() NOR flash internal API to
+ allow reading (and verifying) non-memory-mapped devices
+ * JTAGSPI driver to access SPI NOR flashes via a trivial
+ FPGA proxy
+ * Milandr read/verify for Info memory support
+ * Various discrete SPI NOR flashes support
+ * CFI 16-bit flash reversed endianness support
Board, Target, and Interface Configuration Scripts:
- * STM32W108xx generic target config
- * STM32F429 discovery board config
- * STM32 Nucleo boards configs
- * DENX M53EVK board config
- * Altera Cyclone V SoC, SoCkit config
- * New TI Launchpads board configs
- * TI am43xx devices, AM437x GP EVM, AM438x ePOS EVM board
- configs
- * Marvell Armada 370 family initial support
- * TI TMDX570LS31USB (TMS570, Cortex-R4) support scripts
- * Freescale FRDM-KL25Z, KL46Z board configs
- * Digilent Zedboard config
- * Asus RT-N16, Linksys WRT54GL, BT HomeHub board configs
- * Atmel Xplained initial support
- * Broadcom bcm28155_ap board config
- * TUMPA, TUMPA Lite interface configs
- * Digilent JTAG-SMT2 interface config
- * New RAM testing functions
- * Easy-to-use firmware recovery helpers targetting ordinary
- users with common equipment
+ * Digilent JTAG-HS2, JTAG-HS3 interfaces configs
+ * FTDI UM232H module as JTAG interface config
+ * 100ask's OpenJTAG interface config
+ * MBFTDI interface config
+ * XDS100v3 interface config
+ * Freescale Vybrid VF6xx target config
+ * EmCraft VF6 SOM and baseboard configs
+ * Freescale SabreSD board config
+ * Freescale VF65GS10 tower board config
+ * Pipistrello Xilinx Spartan6 LX45 FPGA board config
+ * miniSpartan6+ board config
+ * Xilinx Kintex7 Development board config
+ * Parallella-I board config
+ * Digilent Atlys and Analog Discovery board configs
+ * Numato Opsis board config
+ * Xilinx Spartan 6 FPGA "Device DNA" reading support
+ * Altera 10M50 FPGA (MAX10 family) target config
+ * Altera EPM240 CPLD (MAXII family) target config
+ * Marsohod2, Marsohod3 FPGA, Marsohod CPLD boards configs
+ * Novena's integrated FPGA board config
+ * XMOS XS1-XAU8A-10's ARM core config
+ * XMOS xCORE-XA Core Module board config
+ * Exynos5250 target config
+ * Arndale board config
+ * FM4 MB9BFxxx family configs
+ * Spansion SK-FM4-U120-9B560 board config
+ * Diolan LPC4357-DB1 board config
+ * ST STM32F469 discovery board config
+ * ST STM32F7-DISCO, STM327[4|5]6G-EVAL boards configs
+ * ST STM32L4 discovery, NUCLEO L476RG, STM32F429I-DISC1 boards
+ configs
+ * Atheros AR2313, AR2315 targets config
+ * Netgear WP102 board config
+ * La Fonera FON2200 board config
+ * Linksys WAG200G board config
+ * LPC-Link2 board config
+ * NXP LPC4370 target config
+ * Atmel SAMV, SAMS, SAME target configs
+ * Atmel SAM E70 Xplained, SAM V71 Xplained Ultra boards
+ configs
+ * Nordic nRF52 target config
+ * Nordic nRF51-DK, nRF52-DK boards configs
+ * Infineon XMC4700 Relax Kit, XMC4800 Relax EtherCAT Kit,
+ XMC4300 Relax EtherCAT Kit boards configs
+ * Renesas S7G2 target config
+ * Renesas DK-S7G2 board config
+ * Altera EP3C10 FPGA (Cyclone III family) target config
+ * TI MSP432P4xx target config
+ * Cypress PSoC 5LP target config
+ * Analog Devices ADSP-SC58x target config (Cortex-A5 core only)
Server Layer:
- * Auto-generation of GDB target description for ARMv7-M,
- ARM4, nds32, OR1K, Quark
- * GDB File-I/O Remote Protocol extension support
- * Default GDB flashing events handlers to initialise and reset
- the target automatically when "load" is used
+ * tcl_trace command for async target trace output via Tcl RPC
Documentation:
- * Extensive README* changes
- * The official User's Guide was proofread
- * Example cross-build script
- * RTOS documentation improvements
- * Tcl RPC documentation and examples added
Build and Release:
- * *BSD, OS X, clang, ARM, windows build fixes
- * New pkg-config support changes the way libusb (and other
- dependencies) are handled. Many adapter drivers are now
- selected automatically during the configure stage.
+ * Various fixes thanks to http://coccinellery.org/
+ * libftdi is now autodetected with pkgconfig
+ * Releases should now support reproducible builds
+ * Conversion to non-recursive make, requires automake >= 1.14
+ * Udev rules modified to add uaccess tag and moved to
+ 60-openocd.rules
+ * Support searching for scripts relative to the openocd binary
+ for all major architectures
This release also contains a number of other important functional and
cosmetic bugfixes. For more details about what has changed since the
last release, see the git repository history:
-http://sourceforge.net/p/openocd/code/ci/v0.8.0/log/?path=
+http://sourceforge.net/p/openocd/code/ci/v0.10.0-rc1/log/?path=
For older NEWS, see the NEWS files associated with each release
projects / openocd / blobdiff