-This file should include highlights of the changes made in the
-OpenOCD openocd-0.3.0 source archive release. See the repository
-history for details about what changed, including bugfixes and
-other issues not mentioned here.
+This file includes highlights of the changes made in the OpenOCD
+source archive release.
JTAG Layer:
- FT2232H (high speed USB) support doesn't need separate configuration
- New reset_config options for SRST gating the JTAG clock (or not)
- TAP declaration no longer requires ircapture and mask attributes
- New "post-reset" event handler for TAP-invariant setup code
- Overridable Tcl "init_reset" and "jtag_init" procedures
+ * New driver for J-Link adapters based on libjaylink
+ (including support for FPGA configuration and EMUCOM)
+ * FTDI improvements to work at 30MHz clock
+ * BCM2835 native driver SWD and Raspberry Pi2 support
+ * BCM2835 is set to 4ma drive, slow slew rate
+ * ixo-usb-jtag (emulation of an Altera Bus Blaster I on
+ Cypress FX2 IC) support
+ * JTAG pass-through mode for CMSIS-DAP (including support for
+ FPGA configuration)
+ * OpenJTAG support for Cypress CY7C65215
+ * connect_assert_srst support for SWD
+ * Xilinx Virtex-II Series7 bitstream loading support
+ * Use JEP106 data to decode IDs
+ * Deprecated "ft2232" driver removed (use "ftdi" instead)
+ * GPL-incompatible FTDI D2XX library support dropped (Presto,
+ OpenJTAG and USB-Blaster I are using libftdi only now)
+ * ZY1000 support dropped (unmaintained since long)
+ * oocd_trace support dropped
+
+Boundary Scan:
Target Layer:
- New commands for use with Cortex-M3 processors:
- "cortex_m3 disassemble" ... Thumb2 disassembly (UAL format)
- "cortex_m3 vector_catch" ... traps certain hardware faults
- without tying up breakpoint resources
- If you're willing to help debug it
- VERY EARLY Cortex-A8 and ARMv7A support
- Updated BeagleBoard.org hardware support
- New commands for use with XScale processors: "xscale vector_table"
- ARM9
- name change: "arm9 vector_catch" not "arm9tdmi vector_catch"
- ARM11
- single stepping support for i.MX31
- bugfix for missing "arm11" prefix on "arm11 memwrite ..."
- ETM support
- Unavailable registers are not listed
+ * ARMv7-A, Cortex-M, Cortex-A/R important fixes and
+ improvements (allowing e.g. simultaneous debugging of A8 and
+ M3 cores, JTAG WAIT support etc.)
+ * ARM Cortex-A,R allow interrupt disable during single-step
+ (maskisr command)
+ * Semihosting support for ARMv7-A
+ * ARM Cortex-M7 support
+ * Intel Quark mcu D2000 support
+ * Freescale LS102x SAP support
+ * ThreadX RTOS support on ARM926E-JS
+ * Cortex-M RTOS stack alignment fixes
+ * FreeRTOS FPU support
+ * uC/OS-III RTOS support
+ * bridging semihosting to GDB's File-I/O support
+ * -defer-examine option added to target create command
+ * verify_image_checksum command added
Flash Layer:
- The lpc2000 driver handles the new NXP LPC1700 (Cortex-M3) chips
- New lpc2900 driver for NXP LPC2900 chips (ARM968 based)
- New "last" flag for NOR "flash erase_sector" and "flash protect"
- The "nand erase N" command now erases all of bank N
+ * Atmel SAM4S, SAM4N, SAM4C support
+ * Atmel SAMV, SAMS, SAME (Cortex-M7) support
+ * Atmel AT91SAMD handle reset run/halt in DSU, other fixes
+ * Atmel AT91SAML21, SAML22, SAMC20/SAMC21, SAMD09 support
+ * ST STM32F4x support
+ * ST STM32F74x/76x/77x, STM32L4 support
+ * ST STM32L0 categories 1, 2 and 5 support
+ * Kinetis K02, K21, K22, K24, K26, K63, K64, K66 support
+ * Kinetis KE, KVx, K8x families support
+ * Kinetis FlexNVM handling
+ * Kinetis flash protection, security, mass_erase improvements
+ * Infineon XMC4xxx family support
+ * Infineon XMC1000 flash driver
+ * Energy Micro EFM32 Happy Gecko support
+ * Energy Micro EFM32 debug interface lock support
+ * Analog Devices ADuCM360 support
+ * Unified Nuvoton NuMicro flash driver
+ * NIIET K1921VK01T (Cortex-M4) support
+ * Nordic Semiconductor nRF51 improvements
+ * Spansion FM4 flash (including MB9BFx64/x65, S6E2DH) driver
+ * Ambiq Micro Apollo flash driver
+ * PIC32MX new device IDs, 17x/27x flash support
+ * read_bank() and verify_bank() NOR flash internal API to
+ allow reading (and verifying) non-memory-mapped devices
+ * JTAGSPI driver to access SPI NOR flashes via a trivial
+ FPGA proxy
+ * Milandr read/verify for Info memory support
+ * Various discrete SPI NOR flashes support
+ * CFI 16-bit flash reversed endianness support
Board, Target, and Interface Configuration Scripts:
- Amontec JTAGkey2 support
- Cleanup and additions for the TI/Luminary Stellaris scripts
- LPC1768 target (and flash) support
- Keil MCB1700 eval board
- Samsung s3c2450
- Mini2440 board
- Numeric TAP and Target identifiers now trigger warnings
- PXA255 partially enumerates
+ * Digilent JTAG-HS2, JTAG-HS3 interfaces configs
+ * FTDI UM232H module as JTAG interface config
+ * 100ask's OpenJTAG interface config
+ * MBFTDI interface config
+ * XDS100v3 interface config
+ * Freescale Vybrid VF6xx target config
+ * EmCraft VF6 SOM and baseboard configs
+ * Freescale SabreSD board config
+ * Freescale VF65GS10 tower board config
+ * Pipistrello Xilinx Spartan6 LX45 FPGA board config
+ * miniSpartan6+ board config
+ * Xilinx Kintex7 Development board config
+ * Parallella-I board config
+ * Digilent Atlys and Analog Discovery board configs
+ * Numato Opsis board config
+ * Xilinx Spartan 6 FPGA "Device DNA" reading support
+ * Altera 10M50 FPGA (MAX10 family) target config
+ * Altera EPM240 CPLD (MAXII family) target config
+ * Marsohod2, Marsohod3 FPGA, Marsohod CPLD boards configs
+ * Novena's integrated FPGA board config
+ * XMOS XS1-XAU8A-10's ARM core config
+ * XMOS xCORE-XA Core Module board config
+ * Exynos5250 target config
+ * Arndale board config
+ * FM4 MB9BFxxx family configs
+ * Spansion SK-FM4-U120-9B560 board config
+ * Diolan LPC4357-DB1 board config
+ * ST STM32F469 discovery board config
+ * ST STM32F7-DISCO, STM327[4|5]6G-EVAL boards configs
+ * ST STM32L4 discovery, NUCLEO L476RG, STM32F429I-DISC1 boards
+ configs
+ * Atheros AR2313, AR2315 targets config
+ * Netgear WP102 board config
+ * La Fonera FON2200 board config
+ * Linksys WAG200G board config
+ * LPC-Link2 board config
+ * NXP LPC4370 target config
+ * Atmel SAMV, SAMS, SAME target configs
+ * Atmel SAM E70 Xplained, SAM V71 Xplained Ultra boards
+ configs
+ * Nordic nRF52 target config
+ * Nordic nRF51-DK, nRF52-DK boards configs
+ * Infineon XMC4700 Relax Kit, XMC4800 Relax EtherCAT Kit,
+ XMC4300 Relax EtherCAT Kit boards configs
+ * Renesas S7G2 target config
+ * Renesas DK-S7G2 board config
+ * Altera EP3C10 FPGA (Cyclone III family) target config
+ * TI MSP432P4xx target config
+ * Cypress PSoC 5LP target config
+ * Analog Devices ADSP-SC58x target config (Cortex-A5 core only)
+
+Server Layer:
+ * tcl_trace command for async target trace output via Tcl RPC
Documentation:
- Capture more debugging and setup advice
- Notes on target source code changes that may help debugging
Build and Release:
+ * Various fixes thanks to http://coccinellery.org/
+ * libftdi is now autodetected with pkgconfig
+ * Releases should now support reproducible builds
+ * Conversion to non-recursive make, requires automake >= 1.14
+ * Udev rules modified to add uaccess tag and moved to
+ 60-openocd.rules
+ * Support searching for scripts relative to the openocd binary
+ for all major architectures
+
+
+This release also contains a number of other important functional and
+cosmetic bugfixes. For more details about what has changed since the
+last release, see the git repository history:
+
+http://sourceforge.net/p/openocd/code/ci/v0.10.0-rc1/log/?path=
+
-For more details about what has changed since the last release,
-see the ChangeLog associated with this source archive. For older NEWS,
-see the NEWS files associated with each release (i.e. NEWS-<version>).
+For older NEWS, see the NEWS files associated with each release
+(i.e. NEWS-<version>).
For more information about contributing test reports, bug fixes, or new
features and device support, please read the new Developer Manual (or
-the BUGS and PATCHES files in the source archive).
+the BUGS and PATCHES.txt files in the source archive).
projects / openocd / blobdiff