Restore normal development cycle

Signed-off-by: Paul Fertser <fercerpav@gmail.com>

diff --git a/NEWS b/NEWS
index e3b1e2565e5f0f87b3e95e065b655df3a6b0fd7a..9df165004a17b561a1a9b7f37a9506a7cfb53a6f 100644 (file)
--- a/NEWS
+++ b/NEWS
@@ -2,149 +2,27 @@ This file includes highlights of the changes made in the OpenOCD
 source archive release.
 
 JTAG Layer:
-       * New driver for J-Link adapters based on libjaylink
-          (including support for FPGA configuration, SWO and EMUCOM)
-       * FTDI improvements to work at 30MHz clock
-       * BCM2835 native driver SWD and Raspberry Pi2 support
-       * BCM2835 is set to 4ma drive, slow slew rate
-       * ixo-usb-jtag (emulation of an Altera Bus Blaster I on
-          Cypress FX2 IC) support
-       * JTAG pass-through mode for CMSIS-DAP (including support for
-          FPGA configuration)
-       * OpenJTAG support for Cypress CY7C65215
-       * connect_assert_srst support for SWD
-       * Xilinx Virtex-II Series7 bitstream loading support
-       * Use JEP106 data to decode IDs
-       * Deprecated "ft2232" driver removed (use "ftdi" instead)
-       * GPL-incompatible FTDI D2XX library support dropped (Presto,
-          OpenJTAG and USB-Blaster I are using libftdi only now)
-       * ZY1000 support dropped (unmaintained since long)
-       * oocd_trace support dropped
 
 Boundary Scan:
 
 Target Layer:
-       * ARMv7-A, Cortex-M, Cortex-A/R important fixes and
-          improvements (allowing e.g. simultaneous debugging of A8 and
-          M3 cores, JTAG WAIT support etc.)
-       * ARM Cortex-A,R allow interrupt disable during single-step
-          (maskisr command)
-       * Semihosting support for ARMv7-A
-       * ARM Cortex-M7 support
-       * Intel Quark mcu D2000 support
-       * Freescale LS102x SAP support
-       * ThreadX RTOS support on ARM926E-JS
-       * Cortex-M RTOS stack alignment fixes
-       * FreeRTOS FPU support
-       * uC/OS-III RTOS support
-       * bridging semihosting to GDB's File-I/O support
-       * -defer-examine option added to target create command
-       * verify_image_checksum command added
 
 Flash Layer:
-       * Atmel SAM4S, SAM4N, SAM4C support
-       * Atmel SAMV, SAMS, SAME (Cortex-M7) support
-       * Atmel AT91SAMD handle reset run/halt in DSU, other fixes
-       * Atmel AT91SAML21, SAML22, SAMC20/SAMC21, SAMD09 support
-       * ST STM32F4x support
-       * ST STM32F74x/76x/77x, STM32L4 support
-       * ST STM32L0 categories 1, 2 and 5 support
-       * Kinetis K02, K21, K22, K24, K26, K63, K64, K66 support
-       * Kinetis KE, KVx, K8x families support
-       * Kinetis FlexNVM handling
-       * Kinetis flash protection, security, mass_erase improvements
-       * Infineon XMC4xxx family support
-       * Infineon XMC1000 flash driver
-       * Energy Micro EFM32 Happy Gecko support
-       * Energy Micro EFM32 debug interface lock support
-       * Analog Devices ADuCM360 support
-       * Unified Nuvoton NuMicro flash driver
-       * NIIET K1921VK01T (Cortex-M4) support
-       * Nordic Semiconductor nRF51 improvements
-       * Spansion FM4 flash (including MB9BFx64/x65, S6E2DH) driver
-       * Ambiq Micro Apollo flash driver
-       * PIC32MX new device IDs, 17x/27x flash support
-       * read_bank() and verify_bank() NOR flash internal API to
-          allow reading (and verifying) non-memory-mapped devices
-       * JTAGSPI driver to access SPI NOR flashes via a trivial
-          FPGA proxy
-       * Milandr read/verify for Info memory support
-       * Various discrete SPI NOR flashes support
-       * CFI 16-bit flash reversed endianness support
 
 Board, Target, and Interface Configuration Scripts:
-       * Digilent JTAG-HS2, JTAG-HS3 interfaces configs
-       * FTDI UM232H module as JTAG interface config
-       * 100ask's OpenJTAG interface config
-       * MBFTDI interface config
-       * XDS100v3 interface config
-       * Freescale Vybrid VF6xx target config
-       * EmCraft VF6 SOM and baseboard configs
-       * Freescale SabreSD board config
-       * Freescale VF65GS10 tower board config
-       * Pipistrello Xilinx Spartan6 LX45 FPGA board config
-       * miniSpartan6+ board config
-       * Xilinx Kintex7 Development board config
-       * Parallella-I board config
-       * Digilent Atlys and Analog Discovery board configs
-       * Numato Opsis board config
-       * Xilinx Spartan 6 FPGA "Device DNA" reading support
-       * Altera 10M50 FPGA (MAX10 family) target config
-       * Altera EPM240 CPLD (MAXII family) target config
-       * Marsohod2, Marsohod3 FPGA, Marsohod CPLD boards configs
-       * Novena's integrated FPGA board config
-       * XMOS XS1-XAU8A-10's ARM core config
-       * XMOS xCORE-XA Core Module board config
-       * Exynos5250 target config
-       * Arndale board config
-       * FM4 MB9BFxxx family configs
-       * Spansion SK-FM4-U120-9B560 board config
-       * Diolan LPC4357-DB1 board config
-       * ST STM32F469 discovery board config
-       * ST STM32F7-DISCO, STM327[4|5]6G-EVAL boards configs
-       * ST STM32L4 discovery, NUCLEO L476RG, STM32F429I-DISC1 boards
-          configs
-       * Atheros AR2313, AR2315 targets config
-       * Netgear WP102 board config
-       * La Fonera FON2200 board config
-       * Linksys WAG200G board config
-       * LPC-Link2 board config
-       * NXP LPC4370 target config
-       * Atmel SAMV, SAMS, SAME target configs
-       * Atmel SAM E70 Xplained, SAM V71 Xplained Ultra boards
-          configs
-       * Nordic nRF52 target config
-       * Nordic nRF51-DK, nRF52-DK boards configs
-       * Infineon XMC4700 Relax Kit, XMC4800 Relax EtherCAT Kit,
-          XMC4300 Relax EtherCAT Kit boards configs
-       * Renesas S7G2 target config
-       * Renesas DK-S7G2 board config
-       * Altera EP3C10 FPGA (Cyclone III family) target config
-       * TI MSP432P4xx target config
-       * Cypress PSoC 5LP target config
-       * Analog Devices ADSP-SC58x target config (Cortex-A5 core only)
 
 Server Layer:
-       * tcl_trace command for async target trace output via Tcl RPC
 
 Documentation:
 
 Build and Release:
-       * Various fixes thanks to http://coccinellery.org/
-       * libftdi is now autodetected with pkgconfig
-       * Releases should now support reproducible builds
-       * Conversion to non-recursive make, requires automake >= 1.14
-       * Udev rules modified to add uaccess tag and moved to
-          60-openocd.rules
-       * Support searching for scripts relative to the openocd binary
-          for all major architectures
 
 
 This release also contains a number of other important functional and
 cosmetic bugfixes. For more details about what has changed since the
 last release, see the git repository history:
 
-http://sourceforge.net/p/openocd/code/ci/v0.10.0/log/?path=
+http://sourceforge.net/p/openocd/code/ci/v0.x.0/log/?path=
 
 
 For older NEWS, see the NEWS files associated with each release

diff --git a/NEWS-0.10.0 b/NEWS-0.10.0
new file mode 100644 (file)
index 0000000..e3b1e25
--- /dev/null
+++ b/NEWS-0.10.0
@@ -0,0 +1,155 @@
+This file includes highlights of the changes made in the OpenOCD
+source archive release.
+
+JTAG Layer:
+       * New driver for J-Link adapters based on libjaylink
+          (including support for FPGA configuration, SWO and EMUCOM)
+       * FTDI improvements to work at 30MHz clock
+       * BCM2835 native driver SWD and Raspberry Pi2 support
+       * BCM2835 is set to 4ma drive, slow slew rate
+       * ixo-usb-jtag (emulation of an Altera Bus Blaster I on
+          Cypress FX2 IC) support
+       * JTAG pass-through mode for CMSIS-DAP (including support for
+          FPGA configuration)
+       * OpenJTAG support for Cypress CY7C65215
+       * connect_assert_srst support for SWD
+       * Xilinx Virtex-II Series7 bitstream loading support
+       * Use JEP106 data to decode IDs
+       * Deprecated "ft2232" driver removed (use "ftdi" instead)
+       * GPL-incompatible FTDI D2XX library support dropped (Presto,
+          OpenJTAG and USB-Blaster I are using libftdi only now)
+       * ZY1000 support dropped (unmaintained since long)
+       * oocd_trace support dropped
+
+Boundary Scan:
+
+Target Layer:
+       * ARMv7-A, Cortex-M, Cortex-A/R important fixes and
+          improvements (allowing e.g. simultaneous debugging of A8 and
+          M3 cores, JTAG WAIT support etc.)
+       * ARM Cortex-A,R allow interrupt disable during single-step
+          (maskisr command)
+       * Semihosting support for ARMv7-A
+       * ARM Cortex-M7 support
+       * Intel Quark mcu D2000 support
+       * Freescale LS102x SAP support
+       * ThreadX RTOS support on ARM926E-JS
+       * Cortex-M RTOS stack alignment fixes
+       * FreeRTOS FPU support
+       * uC/OS-III RTOS support
+       * bridging semihosting to GDB's File-I/O support
+       * -defer-examine option added to target create command
+       * verify_image_checksum command added
+
+Flash Layer:
+       * Atmel SAM4S, SAM4N, SAM4C support
+       * Atmel SAMV, SAMS, SAME (Cortex-M7) support
+       * Atmel AT91SAMD handle reset run/halt in DSU, other fixes
+       * Atmel AT91SAML21, SAML22, SAMC20/SAMC21, SAMD09 support
+       * ST STM32F4x support
+       * ST STM32F74x/76x/77x, STM32L4 support
+       * ST STM32L0 categories 1, 2 and 5 support
+       * Kinetis K02, K21, K22, K24, K26, K63, K64, K66 support
+       * Kinetis KE, KVx, K8x families support
+       * Kinetis FlexNVM handling
+       * Kinetis flash protection, security, mass_erase improvements
+       * Infineon XMC4xxx family support
+       * Infineon XMC1000 flash driver
+       * Energy Micro EFM32 Happy Gecko support
+       * Energy Micro EFM32 debug interface lock support
+       * Analog Devices ADuCM360 support
+       * Unified Nuvoton NuMicro flash driver
+       * NIIET K1921VK01T (Cortex-M4) support
+       * Nordic Semiconductor nRF51 improvements
+       * Spansion FM4 flash (including MB9BFx64/x65, S6E2DH) driver
+       * Ambiq Micro Apollo flash driver
+       * PIC32MX new device IDs, 17x/27x flash support
+       * read_bank() and verify_bank() NOR flash internal API to
+          allow reading (and verifying) non-memory-mapped devices
+       * JTAGSPI driver to access SPI NOR flashes via a trivial
+          FPGA proxy
+       * Milandr read/verify for Info memory support
+       * Various discrete SPI NOR flashes support
+       * CFI 16-bit flash reversed endianness support
+
+Board, Target, and Interface Configuration Scripts:
+       * Digilent JTAG-HS2, JTAG-HS3 interfaces configs
+       * FTDI UM232H module as JTAG interface config
+       * 100ask's OpenJTAG interface config
+       * MBFTDI interface config
+       * XDS100v3 interface config
+       * Freescale Vybrid VF6xx target config
+       * EmCraft VF6 SOM and baseboard configs
+       * Freescale SabreSD board config
+       * Freescale VF65GS10 tower board config
+       * Pipistrello Xilinx Spartan6 LX45 FPGA board config
+       * miniSpartan6+ board config
+       * Xilinx Kintex7 Development board config
+       * Parallella-I board config
+       * Digilent Atlys and Analog Discovery board configs
+       * Numato Opsis board config
+       * Xilinx Spartan 6 FPGA "Device DNA" reading support
+       * Altera 10M50 FPGA (MAX10 family) target config
+       * Altera EPM240 CPLD (MAXII family) target config
+       * Marsohod2, Marsohod3 FPGA, Marsohod CPLD boards configs
+       * Novena's integrated FPGA board config
+       * XMOS XS1-XAU8A-10's ARM core config
+       * XMOS xCORE-XA Core Module board config
+       * Exynos5250 target config
+       * Arndale board config
+       * FM4 MB9BFxxx family configs
+       * Spansion SK-FM4-U120-9B560 board config
+       * Diolan LPC4357-DB1 board config
+       * ST STM32F469 discovery board config
+       * ST STM32F7-DISCO, STM327[4|5]6G-EVAL boards configs
+       * ST STM32L4 discovery, NUCLEO L476RG, STM32F429I-DISC1 boards
+          configs
+       * Atheros AR2313, AR2315 targets config
+       * Netgear WP102 board config
+       * La Fonera FON2200 board config
+       * Linksys WAG200G board config
+       * LPC-Link2 board config
+       * NXP LPC4370 target config
+       * Atmel SAMV, SAMS, SAME target configs
+       * Atmel SAM E70 Xplained, SAM V71 Xplained Ultra boards
+          configs
+       * Nordic nRF52 target config
+       * Nordic nRF51-DK, nRF52-DK boards configs
+       * Infineon XMC4700 Relax Kit, XMC4800 Relax EtherCAT Kit,
+          XMC4300 Relax EtherCAT Kit boards configs
+       * Renesas S7G2 target config
+       * Renesas DK-S7G2 board config
+       * Altera EP3C10 FPGA (Cyclone III family) target config
+       * TI MSP432P4xx target config
+       * Cypress PSoC 5LP target config
+       * Analog Devices ADSP-SC58x target config (Cortex-A5 core only)
+
+Server Layer:
+       * tcl_trace command for async target trace output via Tcl RPC
+
+Documentation:
+
+Build and Release:
+       * Various fixes thanks to http://coccinellery.org/
+       * libftdi is now autodetected with pkgconfig
+       * Releases should now support reproducible builds
+       * Conversion to non-recursive make, requires automake >= 1.14
+       * Udev rules modified to add uaccess tag and moved to
+          60-openocd.rules
+       * Support searching for scripts relative to the openocd binary
+          for all major architectures
+
+
+This release also contains a number of other important functional and
+cosmetic bugfixes. For more details about what has changed since the
+last release, see the git repository history:
+
+http://sourceforge.net/p/openocd/code/ci/v0.10.0/log/?path=
+
+
+For older NEWS, see the NEWS files associated with each release
+(i.e. NEWS-<version>).
+
+For more information about contributing test reports, bug fixes, or new
+features and device support, please read the new Developer Manual (or
+the BUGS and PATCHES.txt files in the source archive).

diff --git a/configure.ac b/configure.ac
index 6949402a3c2d6061905f91c9086199c85af14eda..2543eca3a0b63ee106b98b5d1ff6acee95187109 100644 (file)
--- a/configure.ac
+++ b/configure.ac
@@ -1,5 +1,5 @@
 AC_PREREQ(2.64)
-AC_INIT([openocd], [0.10.0],
+AC_INIT([openocd], [0.10.0+dev],
   [OpenOCD Mailing List <openocd-devel@lists.sourceforge.net>])
 AC_CONFIG_SRCDIR([src/openocd.c])