git.sur5r.net Git - u-boot/blob - drivers/mtd/nand/tegra_nand.c

   1 /*
   2  * Copyright (c) 2011 The Chromium OS Authors.
   3  * (C) Copyright 2011 NVIDIA Corporation <www.nvidia.com>
   4  * (C) Copyright 2006 Detlev Zundel, dzu@denx.de
   5  * (C) Copyright 2006 DENX Software Engineering
   6  *
   7  * SPDX-License-Identifier:     GPL-2.0+
   8  */
   9
  10 #include <common.h>
  11 #include <asm/io.h>
  12 #include <memalign.h>
  13 #include <nand.h>
  14 #include <asm/arch/clock.h>
  15 #include <asm/arch/funcmux.h>
  16 #include <asm/arch-tegra/clk_rst.h>
  17 #include <linux/errno.h>
  18 #include <asm/gpio.h>
  19 #include <fdtdec.h>
  20 #include <bouncebuf.h>
  21 #include "tegra_nand.h"
  22
  23 DECLARE_GLOBAL_DATA_PTR;
  24
  25 #define NAND_CMD_TIMEOUT_MS             10
  26
  27 #define SKIPPED_SPARE_BYTES             4
  28
  29 /* ECC bytes to be generated for tag data */
  30 #define TAG_ECC_BYTES                   4
  31
  32 /* 64 byte oob block info for large page (== 2KB) device
  33  *
  34  * OOB flash layout for Tegra with Reed-Solomon 4 symbol correct ECC:
  35  *      Skipped bytes(4)
  36  *      Main area Ecc(36)
  37  *      Tag data(20)
  38  *      Tag data Ecc(4)
  39  *
  40  * Yaffs2 will use 16 tag bytes.
  41  */
  42 static struct nand_ecclayout eccoob = {
  43         .eccbytes = 36,
  44         .eccpos = {
  45                 4,  5,  6,  7,  8,  9,  10, 11, 12,
  46                 13, 14, 15, 16, 17, 18, 19, 20, 21,
  47                 22, 23, 24, 25, 26, 27, 28, 29, 30,
  48                 31, 32, 33, 34, 35, 36, 37, 38, 39,
  49         },
  50         .oobavail = 20,
  51         .oobfree = {
  52                         {
  53                         .offset = 40,
  54                         .length = 20,
  55                         },
  56         }
  57 };
  58
  59 enum {
  60         ECC_OK,
  61         ECC_TAG_ERROR = 1 << 0,
  62         ECC_DATA_ERROR = 1 << 1
  63 };
  64
  65 /* Timing parameters */
  66 enum {
  67         FDT_NAND_MAX_TRP_TREA,
  68         FDT_NAND_TWB,
  69         FDT_NAND_MAX_TCR_TAR_TRR,
  70         FDT_NAND_TWHR,
  71         FDT_NAND_MAX_TCS_TCH_TALS_TALH,
  72         FDT_NAND_TWH,
  73         FDT_NAND_TWP,
  74         FDT_NAND_TRH,
  75         FDT_NAND_TADL,
  76
  77         FDT_NAND_TIMING_COUNT
  78 };
  79
  80 /* Information about an attached NAND chip */
  81 struct fdt_nand {
  82         struct nand_ctlr *reg;
  83         int enabled;            /* 1 to enable, 0 to disable */
  84         struct gpio_desc wp_gpio;       /* write-protect GPIO */
  85         s32 width;              /* bit width, normally 8 */
  86         u32 timing[FDT_NAND_TIMING_COUNT];
  87 };
  88
  89 struct nand_drv {
  90         struct nand_ctlr *reg;
  91         struct fdt_nand config;
  92 };
  93
  94 static struct nand_drv nand_ctrl;
  95 static struct mtd_info *our_mtd;
  96 static struct nand_chip nand_chip[CONFIG_SYS_MAX_NAND_DEVICE];
  97
  98 /**
  99  * Wait for command completion
 100  *
 101  * @param reg   nand_ctlr structure
 102  * @return
 103  *      1 - Command completed
 104  *      0 - Timeout
 105  */
 106 static int nand_waitfor_cmd_completion(struct nand_ctlr *reg)
 107 {
 108         u32 reg_val;
 109         int running;
 110         int i;
 111
 112         for (i = 0; i < NAND_CMD_TIMEOUT_MS * 1000; i++) {
 113                 if ((readl(&reg->command) & CMD_GO) ||
 114                                 !(readl(&reg->status) & STATUS_RBSY0) ||
 115                                 !(readl(&reg->isr) & ISR_IS_CMD_DONE)) {
 116                         udelay(1);
 117                         continue;
 118                 }
 119                 reg_val = readl(&reg->dma_mst_ctrl);
 120                 /*
 121                  * If DMA_MST_CTRL_EN_A_ENABLE or DMA_MST_CTRL_EN_B_ENABLE
 122                  * is set, that means DMA engine is running.
 123                  *
 124                  * Then we have to wait until DMA_MST_CTRL_IS_DMA_DONE
 125                  * is cleared, indicating DMA transfer completion.
 126                  */
 127                 running = reg_val & (DMA_MST_CTRL_EN_A_ENABLE |
 128                                 DMA_MST_CTRL_EN_B_ENABLE);
 129                 if (!running || (reg_val & DMA_MST_CTRL_IS_DMA_DONE))
 130                         return 1;
 131                 udelay(1);
 132         }
 133         return 0;
 134 }
 135
 136 /**
 137  * Read one byte from the chip
 138  *
 139  * @param mtd   MTD device structure
 140  * @return      data byte
 141  *
 142  * Read function for 8bit bus-width
 143  */
 144 static uint8_t read_byte(struct mtd_info *mtd)
 145 {
 146         struct nand_chip *chip = mtd_to_nand(mtd);
 147         struct nand_drv *info;
 148
 149         info = (struct nand_drv *)nand_get_controller_data(chip);
 150
 151         writel(CMD_GO | CMD_PIO | CMD_RX | CMD_CE0 | CMD_A_VALID,
 152                &info->reg->command);
 153         if (!nand_waitfor_cmd_completion(info->reg))
 154                 printf("Command timeout\n");
 155
 156         return (uint8_t)readl(&info->reg->resp);
 157 }
 158
 159 /**
 160  * Read len bytes from the chip into a buffer
 161  *
 162  * @param mtd   MTD device structure
 163  * @param buf   buffer to store data to
 164  * @param len   number of bytes to read
 165  *
 166  * Read function for 8bit bus-width
 167  */
 168 static void read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
 169 {
 170         int i, s;
 171         unsigned int reg;
 172         struct nand_chip *chip = mtd_to_nand(mtd);
 173         struct nand_drv *info = (struct nand_drv *)nand_get_controller_data(chip);
 174
 175         for (i = 0; i < len; i += 4) {
 176                 s = (len - i) > 4 ? 4 : len - i;
 177                 writel(CMD_PIO | CMD_RX | CMD_A_VALID | CMD_CE0 |
 178                         ((s - 1) << CMD_TRANS_SIZE_SHIFT) | CMD_GO,
 179                         &info->reg->command);
 180                 if (!nand_waitfor_cmd_completion(info->reg))
 181                         puts("Command timeout during read_buf\n");
 182                 reg = readl(&info->reg->resp);
 183                 memcpy(buf + i, &reg, s);
 184         }
 185 }
 186
 187 /**
 188  * Check NAND status to see if it is ready or not
 189  *
 190  * @param mtd   MTD device structure
 191  * @return
 192  *      1 - ready
 193  *      0 - not ready
 194  */
 195 static int nand_dev_ready(struct mtd_info *mtd)
 196 {
 197         struct nand_chip *chip = mtd_to_nand(mtd);
 198         int reg_val;
 199         struct nand_drv *info;
 200
 201         info = (struct nand_drv *)nand_get_controller_data(chip);
 202
 203         reg_val = readl(&info->reg->status);
 204         if (reg_val & STATUS_RBSY0)
 205                 return 1;
 206         else
 207                 return 0;
 208 }
 209
 210 /* Dummy implementation: we don't support multiple chips */
 211 static void nand_select_chip(struct mtd_info *mtd, int chipnr)
 212 {
 213         switch (chipnr) {
 214         case -1:
 215         case 0:
 216                 break;
 217
 218         default:
 219                 BUG();
 220         }
 221 }
 222
 223 /**
 224  * Clear all interrupt status bits
 225  *
 226  * @param reg   nand_ctlr structure
 227  */
 228 static void nand_clear_interrupt_status(struct nand_ctlr *reg)
 229 {
 230         u32 reg_val;
 231
 232         /* Clear interrupt status */
 233         reg_val = readl(&reg->isr);
 234         writel(reg_val, &reg->isr);
 235 }
 236
 237 /**
 238  * Send command to NAND device
 239  *
 240  * @param mtd           MTD device structure
 241  * @param command       the command to be sent
 242  * @param column        the column address for this command, -1 if none
 243  * @param page_addr     the page address for this command, -1 if none
 244  */
 245 static void nand_command(struct mtd_info *mtd, unsigned int command,
 246         int column, int page_addr)
 247 {
 248         struct nand_chip *chip = mtd_to_nand(mtd);
 249         struct nand_drv *info;
 250
 251         info = (struct nand_drv *)nand_get_controller_data(chip);
 252
 253         /*
 254          * Write out the command to the device.
 255          *
 256          * Only command NAND_CMD_RESET or NAND_CMD_READID will come
 257          * here before mtd->writesize is initialized.
 258          */
 259
 260         /* Emulate NAND_CMD_READOOB */
 261         if (command == NAND_CMD_READOOB) {
 262                 assert(mtd->writesize != 0);
 263                 column += mtd->writesize;
 264                 command = NAND_CMD_READ0;
 265         }
 266
 267         /* Adjust columns for 16 bit bus-width */
 268         if (column != -1 && (chip->options & NAND_BUSWIDTH_16))
 269                 column >>= 1;
 270
 271         nand_clear_interrupt_status(info->reg);
 272
 273         /* Stop DMA engine, clear DMA completion status */
 274         writel(DMA_MST_CTRL_EN_A_DISABLE
 275                 | DMA_MST_CTRL_EN_B_DISABLE
 276                 | DMA_MST_CTRL_IS_DMA_DONE,
 277                 &info->reg->dma_mst_ctrl);
 278
 279         /*
 280          * Program and erase have their own busy handlers
 281          * status and sequential in needs no delay
 282          */
 283         switch (command) {
 284         case NAND_CMD_READID:
 285                 writel(NAND_CMD_READID, &info->reg->cmd_reg1);
 286                 writel(column & 0xFF, &info->reg->addr_reg1);
 287                 writel(CMD_GO | CMD_CLE | CMD_ALE | CMD_CE0,
 288                        &info->reg->command);
 289                 break;
 290         case NAND_CMD_PARAM:
 291                 writel(NAND_CMD_PARAM, &info->reg->cmd_reg1);
 292                 writel(column & 0xFF, &info->reg->addr_reg1);
 293                 writel(CMD_GO | CMD_CLE | CMD_ALE | CMD_CE0,
 294                         &info->reg->command);
 295                 break;
 296         case NAND_CMD_READ0:
 297                 writel(NAND_CMD_READ0, &info->reg->cmd_reg1);
 298                 writel(NAND_CMD_READSTART, &info->reg->cmd_reg2);
 299                 writel((page_addr << 16) | (column & 0xFFFF),
 300                         &info->reg->addr_reg1);
 301                 writel(page_addr >> 16, &info->reg->addr_reg2);
 302                 return;
 303         case NAND_CMD_SEQIN:
 304                 writel(NAND_CMD_SEQIN, &info->reg->cmd_reg1);
 305                 writel(NAND_CMD_PAGEPROG, &info->reg->cmd_reg2);
 306                 writel((page_addr << 16) | (column & 0xFFFF),
 307                         &info->reg->addr_reg1);
 308                 writel(page_addr >> 16,
 309                         &info->reg->addr_reg2);
 310                 return;
 311         case NAND_CMD_PAGEPROG:
 312                 return;
 313         case NAND_CMD_ERASE1:
 314                 writel(NAND_CMD_ERASE1, &info->reg->cmd_reg1);
 315                 writel(NAND_CMD_ERASE2, &info->reg->cmd_reg2);
 316                 writel(page_addr, &info->reg->addr_reg1);
 317                 writel(CMD_GO | CMD_CLE | CMD_ALE |
 318                         CMD_SEC_CMD | CMD_CE0 | CMD_ALE_BYTES3,
 319                         &info->reg->command);
 320                 break;
 321         case NAND_CMD_ERASE2:
 322                 return;
 323         case NAND_CMD_STATUS:
 324                 writel(NAND_CMD_STATUS, &info->reg->cmd_reg1);
 325                 writel(CMD_GO | CMD_CLE | CMD_PIO | CMD_RX
 326                         | ((1 - 0) << CMD_TRANS_SIZE_SHIFT)
 327                         | CMD_CE0,
 328                         &info->reg->command);
 329                 break;
 330         case NAND_CMD_RESET:
 331                 writel(NAND_CMD_RESET, &info->reg->cmd_reg1);
 332                 writel(CMD_GO | CMD_CLE | CMD_CE0,
 333                         &info->reg->command);
 334                 break;
 335         case NAND_CMD_RNDOUT:
 336         default:
 337                 printf("%s: Unsupported command %d\n", __func__, command);
 338                 return;
 339         }
 340         if (!nand_waitfor_cmd_completion(info->reg))
 341                 printf("Command 0x%02X timeout\n", command);
 342 }
 343
 344 /**
 345  * Check whether the pointed buffer are all 0xff (blank).
 346  *
 347  * @param buf   data buffer for blank check
 348  * @param len   length of the buffer in byte
 349  * @return
 350  *      1 - blank
 351  *      0 - non-blank
 352  */
 353 static int blank_check(u8 *buf, int len)
 354 {
 355         int i;
 356
 357         for (i = 0; i < len; i++)
 358                 if (buf[i] != 0xFF)
 359                         return 0;
 360         return 1;
 361 }
 362
 363 /**
 364  * After a DMA transfer for read, we call this function to see whether there
 365  * is any uncorrectable error on the pointed data buffer or oob buffer.
 366  *
 367  * @param reg           nand_ctlr structure
 368  * @param databuf       data buffer
 369  * @param a_len         data buffer length
 370  * @param oobbuf        oob buffer
 371  * @param b_len         oob buffer length
 372  * @return
 373  *      ECC_OK - no ECC error or correctable ECC error
 374  *      ECC_TAG_ERROR - uncorrectable tag ECC error
 375  *      ECC_DATA_ERROR - uncorrectable data ECC error
 376  *      ECC_DATA_ERROR + ECC_TAG_ERROR - uncorrectable data+tag ECC error
 377  */
 378 static int check_ecc_error(struct nand_ctlr *reg, u8 *databuf,
 379         int a_len, u8 *oobbuf, int b_len)
 380 {
 381         int return_val = ECC_OK;
 382         u32 reg_val;
 383
 384         if (!(readl(&reg->isr) & ISR_IS_ECC_ERR))
 385                 return ECC_OK;
 386
 387         /*
 388          * Area A is used for the data block (databuf). Area B is used for
 389          * the spare block (oobbuf)
 390          */
 391         reg_val = readl(&reg->dec_status);
 392         if ((reg_val & DEC_STATUS_A_ECC_FAIL) && databuf) {
 393                 reg_val = readl(&reg->bch_dec_status_buf);
 394                 /*
 395                  * If uncorrectable error occurs on data area, then see whether
 396                  * they are all FF. If all are FF, it's a blank page.
 397                  * Not error.
 398                  */
 399                 if ((reg_val & BCH_DEC_STATUS_FAIL_SEC_FLAG_MASK) &&
 400                                 !blank_check(databuf, a_len))
 401                         return_val |= ECC_DATA_ERROR;
 402         }
 403
 404         if ((reg_val & DEC_STATUS_B_ECC_FAIL) && oobbuf) {
 405                 reg_val = readl(&reg->bch_dec_status_buf);
 406                 /*
 407                  * If uncorrectable error occurs on tag area, then see whether
 408                  * they are all FF. If all are FF, it's a blank page.
 409                  * Not error.
 410                  */
 411                 if ((reg_val & BCH_DEC_STATUS_FAIL_TAG_MASK) &&
 412                                 !blank_check(oobbuf, b_len))
 413                         return_val |= ECC_TAG_ERROR;
 414         }
 415
 416         return return_val;
 417 }
 418
 419 /**
 420  * Set GO bit to send command to device
 421  *
 422  * @param reg   nand_ctlr structure
 423  */
 424 static void start_command(struct nand_ctlr *reg)
 425 {
 426         u32 reg_val;
 427
 428         reg_val = readl(&reg->command);
 429         reg_val |= CMD_GO;
 430         writel(reg_val, &reg->command);
 431 }
 432
 433 /**
 434  * Clear command GO bit, DMA GO bit, and DMA completion status
 435  *
 436  * @param reg   nand_ctlr structure
 437  */
 438 static void stop_command(struct nand_ctlr *reg)
 439 {
 440         /* Stop command */
 441         writel(0, &reg->command);
 442
 443         /* Stop DMA engine and clear DMA completion status */
 444         writel(DMA_MST_CTRL_GO_DISABLE
 445                 | DMA_MST_CTRL_IS_DMA_DONE,
 446                 &reg->dma_mst_ctrl);
 447 }
 448
 449 /**
 450  * Set up NAND bus width and page size
 451  *
 452  * @param info          nand_info structure
 453  * @param *reg_val      address of reg_val
 454  * @return 0 if ok, -1 on error
 455  */
 456 static int set_bus_width_page_size(struct fdt_nand *config,
 457         u32 *reg_val)
 458 {
 459         if (config->width == 8)
 460                 *reg_val = CFG_BUS_WIDTH_8BIT;
 461         else if (config->width == 16)
 462                 *reg_val = CFG_BUS_WIDTH_16BIT;
 463         else {
 464                 debug("%s: Unsupported bus width %d\n", __func__,
 465                       config->width);
 466                 return -1;
 467         }
 468
 469         if (our_mtd->writesize == 512)
 470                 *reg_val |= CFG_PAGE_SIZE_512;
 471         else if (our_mtd->writesize == 2048)
 472                 *reg_val |= CFG_PAGE_SIZE_2048;
 473         else if (our_mtd->writesize == 4096)
 474                 *reg_val |= CFG_PAGE_SIZE_4096;
 475         else {
 476                 debug("%s: Unsupported page size %d\n", __func__,
 477                       our_mtd->writesize);
 478                 return -1;
 479         }
 480
 481         return 0;
 482 }
 483
 484 /**
 485  * Page read/write function
 486  *
 487  * @param mtd           mtd info structure
 488  * @param chip          nand chip info structure
 489  * @param buf           data buffer
 490  * @param page          page number
 491  * @param with_ecc      1 to enable ECC, 0 to disable ECC
 492  * @param is_writing    0 for read, 1 for write
 493  * @return      0 when successfully completed
 494  *              -EIO when command timeout
 495  */
 496 static int nand_rw_page(struct mtd_info *mtd, struct nand_chip *chip,
 497         uint8_t *buf, int page, int with_ecc, int is_writing)
 498 {
 499         u32 reg_val;
 500         int tag_size;
 501         struct nand_oobfree *free = chip->ecc.layout->oobfree;
 502         /* 4*128=512 (byte) is the value that our HW can support. */
 503         ALLOC_CACHE_ALIGN_BUFFER(u32, tag_buf, 128);
 504         char *tag_ptr;
 505         struct nand_drv *info;
 506         struct fdt_nand *config;
 507         unsigned int bbflags;
 508         struct bounce_buffer bbstate, bbstate_oob;
 509
 510         if ((uintptr_t)buf & 0x03) {
 511                 printf("buf %p has to be 4-byte aligned\n", buf);
 512                 return -EINVAL;
 513         }
 514
 515         info = (struct nand_drv *)nand_get_controller_data(chip);
 516         config = &info->config;
 517         if (set_bus_width_page_size(config, &reg_val))
 518                 return -EINVAL;
 519
 520         /* Need to be 4-byte aligned */
 521         tag_ptr = (char *)tag_buf;
 522
 523         stop_command(info->reg);
 524
 525         if (is_writing)
 526                 bbflags = GEN_BB_READ;
 527         else
 528                 bbflags = GEN_BB_WRITE;
 529
 530         bounce_buffer_start(&bbstate, (void *)buf, 1 << chip->page_shift,
 531                             bbflags);
 532         writel((1 << chip->page_shift) - 1, &info->reg->dma_cfg_a);
 533         writel(virt_to_phys(bbstate.bounce_buffer), &info->reg->data_block_ptr);
 534
 535         /* Set ECC selection, configure ECC settings */
 536         if (with_ecc) {
 537                 if (is_writing)
 538                         memcpy(tag_ptr, chip->oob_poi + free->offset,
 539                                chip->ecc.layout->oobavail + TAG_ECC_BYTES);
 540                 tag_size = chip->ecc.layout->oobavail + TAG_ECC_BYTES;
 541                 reg_val |= (CFG_SKIP_SPARE_SEL_4
 542                         | CFG_SKIP_SPARE_ENABLE
 543                         | CFG_HW_ECC_CORRECTION_ENABLE
 544                         | CFG_ECC_EN_TAG_DISABLE
 545                         | CFG_HW_ECC_SEL_RS
 546                         | CFG_HW_ECC_ENABLE
 547                         | CFG_TVAL4
 548                         | (tag_size - 1));
 549
 550                 if (!is_writing)
 551                         tag_size += SKIPPED_SPARE_BYTES;
 552                 bounce_buffer_start(&bbstate_oob, (void *)tag_ptr, tag_size,
 553                                     bbflags);
 554         } else {
 555                 tag_size = mtd->oobsize;
 556                 reg_val |= (CFG_SKIP_SPARE_DISABLE
 557                         | CFG_HW_ECC_CORRECTION_DISABLE
 558                         | CFG_ECC_EN_TAG_DISABLE
 559                         | CFG_HW_ECC_DISABLE
 560                         | (tag_size - 1));
 561                 bounce_buffer_start(&bbstate_oob, (void *)chip->oob_poi,
 562                                     tag_size, bbflags);
 563         }
 564         writel(reg_val, &info->reg->config);
 565         writel(virt_to_phys(bbstate_oob.bounce_buffer), &info->reg->tag_ptr);
 566         writel(BCH_CONFIG_BCH_ECC_DISABLE, &info->reg->bch_config);
 567         writel(tag_size - 1, &info->reg->dma_cfg_b);
 568
 569         nand_clear_interrupt_status(info->reg);
 570
 571         reg_val = CMD_CLE | CMD_ALE
 572                 | CMD_SEC_CMD
 573                 | (CMD_ALE_BYTES5 << CMD_ALE_BYTE_SIZE_SHIFT)
 574                 | CMD_A_VALID
 575                 | CMD_B_VALID
 576                 | (CMD_TRANS_SIZE_PAGE << CMD_TRANS_SIZE_SHIFT)
 577                 | CMD_CE0;
 578         if (!is_writing)
 579                 reg_val |= (CMD_AFT_DAT_DISABLE | CMD_RX);
 580         else
 581                 reg_val |= (CMD_AFT_DAT_ENABLE | CMD_TX);
 582         writel(reg_val, &info->reg->command);
 583
 584         /* Setup DMA engine */
 585         reg_val = DMA_MST_CTRL_GO_ENABLE
 586                 | DMA_MST_CTRL_BURST_8WORDS
 587                 | DMA_MST_CTRL_EN_A_ENABLE
 588                 | DMA_MST_CTRL_EN_B_ENABLE;
 589
 590         if (!is_writing)
 591                 reg_val |= DMA_MST_CTRL_DIR_READ;
 592         else
 593                 reg_val |= DMA_MST_CTRL_DIR_WRITE;
 594
 595         writel(reg_val, &info->reg->dma_mst_ctrl);
 596
 597         start_command(info->reg);
 598
 599         if (!nand_waitfor_cmd_completion(info->reg)) {
 600                 if (!is_writing)
 601                         printf("Read Page 0x%X timeout ", page);
 602                 else
 603                         printf("Write Page 0x%X timeout ", page);
 604                 if (with_ecc)
 605                         printf("with ECC");
 606                 else
 607                         printf("without ECC");
 608                 printf("\n");
 609                 return -EIO;
 610         }
 611
 612         bounce_buffer_stop(&bbstate_oob);
 613         bounce_buffer_stop(&bbstate);
 614
 615         if (with_ecc && !is_writing) {
 616                 memcpy(chip->oob_poi, tag_ptr,
 617                         SKIPPED_SPARE_BYTES);
 618                 memcpy(chip->oob_poi + free->offset,
 619                         tag_ptr + SKIPPED_SPARE_BYTES,
 620                         chip->ecc.layout->oobavail);
 621                 reg_val = (u32)check_ecc_error(info->reg, (u8 *)buf,
 622                         1 << chip->page_shift,
 623                         (u8 *)(tag_ptr + SKIPPED_SPARE_BYTES),
 624                         chip->ecc.layout->oobavail);
 625                 if (reg_val & ECC_TAG_ERROR)
 626                         printf("Read Page 0x%X tag ECC error\n", page);
 627                 if (reg_val & ECC_DATA_ERROR)
 628                         printf("Read Page 0x%X data ECC error\n",
 629                                 page);
 630                 if (reg_val & (ECC_DATA_ERROR | ECC_TAG_ERROR))
 631                         return -EIO;
 632         }
 633         return 0;
 634 }
 635
 636 /**
 637  * Hardware ecc based page read function
 638  *
 639  * @param mtd   mtd info structure
 640  * @param chip  nand chip info structure
 641  * @param buf   buffer to store read data
 642  * @param page  page number to read
 643  * @return      0 when successfully completed
 644  *              -EIO when command timeout
 645  */
 646 static int nand_read_page_hwecc(struct mtd_info *mtd,
 647         struct nand_chip *chip, uint8_t *buf, int oob_required, int page)
 648 {
 649         return nand_rw_page(mtd, chip, buf, page, 1, 0);
 650 }
 651
 652 /**
 653  * Hardware ecc based page write function
 654  *
 655  * @param mtd   mtd info structure
 656  * @param chip  nand chip info structure
 657  * @param buf   data buffer
 658  */
 659 static int nand_write_page_hwecc(struct mtd_info *mtd,
 660         struct nand_chip *chip, const uint8_t *buf, int oob_required,
 661         int page)
 662 {
 663         nand_rw_page(mtd, chip, (uint8_t *)buf, page, 1, 1);
 664         return 0;
 665 }
 666
 667
 668 /**
 669  * Read raw page data without ecc
 670  *
 671  * @param mtd   mtd info structure
 672  * @param chip  nand chip info structure
 673  * @param buf   buffer to store read data
 674  * @param page  page number to read
 675  * @return      0 when successfully completed
 676  *              -EINVAL when chip->oob_poi is not double-word aligned
 677  *              -EIO when command timeout
 678  */
 679 static int nand_read_page_raw(struct mtd_info *mtd,
 680         struct nand_chip *chip, uint8_t *buf, int oob_required, int page)
 681 {
 682         return nand_rw_page(mtd, chip, buf, page, 0, 0);
 683 }
 684
 685 /**
 686  * Raw page write function
 687  *
 688  * @param mtd   mtd info structure
 689  * @param chip  nand chip info structure
 690  * @param buf   data buffer
 691  */
 692 static int nand_write_page_raw(struct mtd_info *mtd,
 693                 struct nand_chip *chip, const uint8_t *buf,
 694                 int oob_required, int page)
 695 {
 696         nand_rw_page(mtd, chip, (uint8_t *)buf, page, 0, 1);
 697         return 0;
 698 }
 699
 700 /**
 701  * OOB data read/write function
 702  *
 703  * @param mtd           mtd info structure
 704  * @param chip          nand chip info structure
 705  * @param page          page number to read
 706  * @param with_ecc      1 to enable ECC, 0 to disable ECC
 707  * @param is_writing    0 for read, 1 for write
 708  * @return      0 when successfully completed
 709  *              -EINVAL when chip->oob_poi is not double-word aligned
 710  *              -EIO when command timeout
 711  */
 712 static int nand_rw_oob(struct mtd_info *mtd, struct nand_chip *chip,
 713         int page, int with_ecc, int is_writing)
 714 {
 715         u32 reg_val;
 716         int tag_size;
 717         struct nand_oobfree *free = chip->ecc.layout->oobfree;
 718         struct nand_drv *info;
 719         unsigned int bbflags;
 720         struct bounce_buffer bbstate_oob;
 721
 722         if (((int)chip->oob_poi) & 0x03)
 723                 return -EINVAL;
 724         info = (struct nand_drv *)nand_get_controller_data(chip);
 725         if (set_bus_width_page_size(&info->config, &reg_val))
 726                 return -EINVAL;
 727
 728         stop_command(info->reg);
 729
 730         /* Set ECC selection */
 731         tag_size = mtd->oobsize;
 732         if (with_ecc)
 733                 reg_val |= CFG_ECC_EN_TAG_ENABLE;
 734         else
 735                 reg_val |= (CFG_ECC_EN_TAG_DISABLE);
 736
 737         reg_val |= ((tag_size - 1) |
 738                 CFG_SKIP_SPARE_DISABLE |
 739                 CFG_HW_ECC_CORRECTION_DISABLE |
 740                 CFG_HW_ECC_DISABLE);
 741         writel(reg_val, &info->reg->config);
 742
 743         if (is_writing && with_ecc)
 744                 tag_size -= TAG_ECC_BYTES;
 745
 746         if (is_writing)
 747                 bbflags = GEN_BB_READ;
 748         else
 749                 bbflags = GEN_BB_WRITE;
 750
 751         bounce_buffer_start(&bbstate_oob, (void *)chip->oob_poi, tag_size,
 752                             bbflags);
 753         writel(virt_to_phys(bbstate_oob.bounce_buffer), &info->reg->tag_ptr);
 754
 755         writel(BCH_CONFIG_BCH_ECC_DISABLE, &info->reg->bch_config);
 756
 757         writel(tag_size - 1, &info->reg->dma_cfg_b);
 758
 759         nand_clear_interrupt_status(info->reg);
 760
 761         reg_val = CMD_CLE | CMD_ALE
 762                 | CMD_SEC_CMD
 763                 | (CMD_ALE_BYTES5 << CMD_ALE_BYTE_SIZE_SHIFT)
 764                 | CMD_B_VALID
 765                 | CMD_CE0;
 766         if (!is_writing)
 767                 reg_val |= (CMD_AFT_DAT_DISABLE | CMD_RX);
 768         else
 769                 reg_val |= (CMD_AFT_DAT_ENABLE | CMD_TX);
 770         writel(reg_val, &info->reg->command);
 771
 772         /* Setup DMA engine */
 773         reg_val = DMA_MST_CTRL_GO_ENABLE
 774                 | DMA_MST_CTRL_BURST_8WORDS
 775                 | DMA_MST_CTRL_EN_B_ENABLE;
 776         if (!is_writing)
 777                 reg_val |= DMA_MST_CTRL_DIR_READ;
 778         else
 779                 reg_val |= DMA_MST_CTRL_DIR_WRITE;
 780
 781         writel(reg_val, &info->reg->dma_mst_ctrl);
 782
 783         start_command(info->reg);
 784
 785         if (!nand_waitfor_cmd_completion(info->reg)) {
 786                 if (!is_writing)
 787                         printf("Read OOB of Page 0x%X timeout\n", page);
 788                 else
 789                         printf("Write OOB of Page 0x%X timeout\n", page);
 790                 return -EIO;
 791         }
 792
 793         bounce_buffer_stop(&bbstate_oob);
 794
 795         if (with_ecc && !is_writing) {
 796                 reg_val = (u32)check_ecc_error(info->reg, 0, 0,
 797                         (u8 *)(chip->oob_poi + free->offset),
 798                         chip->ecc.layout->oobavail);
 799                 if (reg_val & ECC_TAG_ERROR)
 800                         printf("Read OOB of Page 0x%X tag ECC error\n", page);
 801         }
 802         return 0;
 803 }
 804
 805 /**
 806  * OOB data read function
 807  *
 808  * @param mtd           mtd info structure
 809  * @param chip          nand chip info structure
 810  * @param page          page number to read
 811  */
 812 static int nand_read_oob(struct mtd_info *mtd, struct nand_chip *chip,
 813         int page)
 814 {
 815         chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page);
 816         nand_rw_oob(mtd, chip, page, 0, 0);
 817         return 0;
 818 }
 819
 820 /**
 821  * OOB data write function
 822  *
 823  * @param mtd   mtd info structure
 824  * @param chip  nand chip info structure
 825  * @param page  page number to write
 826  * @return      0 when successfully completed
 827  *              -EINVAL when chip->oob_poi is not double-word aligned
 828  *              -EIO when command timeout
 829  */
 830 static int nand_write_oob(struct mtd_info *mtd, struct nand_chip *chip,
 831         int page)
 832 {
 833         chip->cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize, page);
 834
 835         return nand_rw_oob(mtd, chip, page, 0, 1);
 836 }
 837
 838 /**
 839  * Set up NAND memory timings according to the provided parameters
 840  *
 841  * @param timing        Timing parameters
 842  * @param reg           NAND controller register address
 843  */
 844 static void setup_timing(unsigned timing[FDT_NAND_TIMING_COUNT],
 845                          struct nand_ctlr *reg)
 846 {
 847         u32 reg_val, clk_rate, clk_period, time_val;
 848
 849         clk_rate = (u32)clock_get_periph_rate(PERIPH_ID_NDFLASH,
 850                 CLOCK_ID_PERIPH) / 1000000;
 851         clk_period = 1000 / clk_rate;
 852         reg_val = ((timing[FDT_NAND_MAX_TRP_TREA] / clk_period) <<
 853                 TIMING_TRP_RESP_CNT_SHIFT) & TIMING_TRP_RESP_CNT_MASK;
 854         reg_val |= ((timing[FDT_NAND_TWB] / clk_period) <<
 855                 TIMING_TWB_CNT_SHIFT) & TIMING_TWB_CNT_MASK;
 856         time_val = timing[FDT_NAND_MAX_TCR_TAR_TRR] / clk_period;
 857         if (time_val > 2)
 858                 reg_val |= ((time_val - 2) << TIMING_TCR_TAR_TRR_CNT_SHIFT) &
 859                         TIMING_TCR_TAR_TRR_CNT_MASK;
 860         reg_val |= ((timing[FDT_NAND_TWHR] / clk_period) <<
 861                 TIMING_TWHR_CNT_SHIFT) & TIMING_TWHR_CNT_MASK;
 862         time_val = timing[FDT_NAND_MAX_TCS_TCH_TALS_TALH] / clk_period;
 863         if (time_val > 1)
 864                 reg_val |= ((time_val - 1) << TIMING_TCS_CNT_SHIFT) &
 865                         TIMING_TCS_CNT_MASK;
 866         reg_val |= ((timing[FDT_NAND_TWH] / clk_period) <<
 867                 TIMING_TWH_CNT_SHIFT) & TIMING_TWH_CNT_MASK;
 868         reg_val |= ((timing[FDT_NAND_TWP] / clk_period) <<
 869                 TIMING_TWP_CNT_SHIFT) & TIMING_TWP_CNT_MASK;
 870         reg_val |= ((timing[FDT_NAND_TRH] / clk_period) <<
 871                 TIMING_TRH_CNT_SHIFT) & TIMING_TRH_CNT_MASK;
 872         reg_val |= ((timing[FDT_NAND_MAX_TRP_TREA] / clk_period) <<
 873                 TIMING_TRP_CNT_SHIFT) & TIMING_TRP_CNT_MASK;
 874         writel(reg_val, &reg->timing);
 875
 876         reg_val = 0;
 877         time_val = timing[FDT_NAND_TADL] / clk_period;
 878         if (time_val > 2)
 879                 reg_val = (time_val - 2) & TIMING2_TADL_CNT_MASK;
 880         writel(reg_val, &reg->timing2);
 881 }
 882
 883 /**
 884  * Decode NAND parameters from the device tree
 885  *
 886  * @param blob  Device tree blob
 887  * @param node  Node containing "nand-flash" compatible node
 888  * @return 0 if ok, -ve on error (FDT_ERR_...)
 889  */
 890 static int fdt_decode_nand(const void *blob, int node, struct fdt_nand *config)
 891 {
 892         int err;
 893
 894         config->reg = (struct nand_ctlr *)fdtdec_get_addr(blob, node, "reg");
 895         config->enabled = fdtdec_get_is_enabled(blob, node);
 896         config->width = fdtdec_get_int(blob, node, "nvidia,nand-width", 8);
 897         err = gpio_request_by_name_nodev(offset_to_ofnode(node),
 898                         "nvidia,wp-gpios", 0, &config->wp_gpio, GPIOD_IS_OUT);
 899         if (err)
 900                 return err;
 901         err = fdtdec_get_int_array(blob, node, "nvidia,timing",
 902                         config->timing, FDT_NAND_TIMING_COUNT);
 903         if (err < 0)
 904                 return err;
 905
 906         /* Now look up the controller and decode that */
 907         node = fdt_next_node(blob, node, NULL);
 908         if (node < 0)
 909                 return node;
 910
 911         return 0;
 912 }
 913
 914 /**
 915  * Board-specific NAND initialization
 916  *
 917  * @param nand  nand chip info structure
 918  * @return 0, after initialized, -1 on error
 919  */
 920 int tegra_nand_init(struct nand_chip *nand, int devnum)
 921 {
 922         struct nand_drv *info = &nand_ctrl;
 923         struct fdt_nand *config = &info->config;
 924         int node, ret;
 925
 926         node = fdtdec_next_compatible(gd->fdt_blob, 0,
 927                                       COMPAT_NVIDIA_TEGRA20_NAND);
 928         if (node < 0)
 929                 return -1;
 930         if (fdt_decode_nand(gd->fdt_blob, node, config)) {
 931                 printf("Could not decode nand-flash in device tree\n");
 932                 return -1;
 933         }
 934         if (!config->enabled)
 935                 return -1;
 936         info->reg = config->reg;
 937         nand->ecc.mode = NAND_ECC_HW;
 938         nand->ecc.layout = &eccoob;
 939
 940         nand->options = LP_OPTIONS;
 941         nand->cmdfunc = nand_command;
 942         nand->read_byte = read_byte;
 943         nand->read_buf = read_buf;
 944         nand->ecc.read_page = nand_read_page_hwecc;
 945         nand->ecc.write_page = nand_write_page_hwecc;
 946         nand->ecc.read_page_raw = nand_read_page_raw;
 947         nand->ecc.write_page_raw = nand_write_page_raw;
 948         nand->ecc.read_oob = nand_read_oob;
 949         nand->ecc.write_oob = nand_write_oob;
 950         nand->ecc.strength = 1;
 951         nand->select_chip = nand_select_chip;
 952         nand->dev_ready  = nand_dev_ready;
 953         nand_set_controller_data(nand, &nand_ctrl);
 954
 955         /* Disable subpage writes as we do not provide ecc->hwctl */
 956         nand->options |= NAND_NO_SUBPAGE_WRITE;
 957
 958         /* Adjust controller clock rate */
 959         clock_start_periph_pll(PERIPH_ID_NDFLASH, CLOCK_ID_PERIPH, 52000000);
 960
 961         /* Adjust timing for NAND device */
 962         setup_timing(config->timing, info->reg);
 963
 964         dm_gpio_set_value(&config->wp_gpio, 1);
 965
 966         our_mtd = nand_to_mtd(nand);
 967         ret = nand_scan_ident(our_mtd, CONFIG_SYS_NAND_MAX_CHIPS, NULL);
 968         if (ret)
 969                 return ret;
 970
 971         nand->ecc.size = our_mtd->writesize;
 972         nand->ecc.bytes = our_mtd->oobsize;
 973
 974         ret = nand_scan_tail(our_mtd);
 975         if (ret)
 976                 return ret;
 977
 978         ret = nand_register(devnum, our_mtd);
 979         if (ret)
 980                 return ret;
 981
 982         return 0;
 983 }
 984
 985 void board_nand_init(void)
 986 {
 987         struct nand_chip *nand = &nand_chip[0];
 988
 989         if (tegra_nand_init(nand, 0))
 990                 puts("Tegra NAND init failed\n");
 991 }