CONFIG_CMD_DATE * support for RTC, date/time...
CONFIG_CMD_DHCP * DHCP support
CONFIG_CMD_DIAG * Diagnostics
- CONFIG_CMD_DOC * Disk-On-Chip Support
CONFIG_CMD_DS4510 * ds4510 I2C gpio commands
CONFIG_CMD_DS4510_INFO * ds4510 I2C info command
CONFIG_CMD_DS4510_MEM * ds4510 I2C eeprom/sram commansd
CONFIG_CMD_KGDB * kgdb
CONFIG_CMD_LOADB loadb
CONFIG_CMD_LOADS loads
+ CONFIG_CMD_MD5SUM print md5 message digest
+ (requires CONFIG_CMD_MEMORY and CONFIG_MD5)
CONFIG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
loop, loopw, mtest
CONFIG_CMD_MISC Misc functions like sleep etc
(requires CONFIG_CMD_I2C)
CONFIG_CMD_SETGETDCR Support for DCR Register access
(4xx only)
+ CONFIG_CMD_SHA1 print sha1 memory digest
+ (requires CONFIG_CMD_MEMORY)
CONFIG_CMD_SOURCE "source" command Support
CONFIG_CMD_SPI * SPI serial bus support
CONFIG_CMD_USB * USB support
MPC5200 USB requires additional defines:
CONFIG_USB_CLOCK
for 528 MHz Clock: 0x0001bbbb
+ CONFIG_PSC3_USB
+ for USB on PSC3
CONFIG_USB_CONFIG
for differential drivers: 0x00001000
for single ended drivers: 0x00005000
+ for differential drivers on PSC3: 0x00000100
+ for single ended drivers on PSC3: 0x00004100
CONFIG_SYS_USB_EVENT_POLL
May be defined to allow interrupt polling
instead of using asynchronous interrupts
allows for a "silent" boot where a splash screen is
loaded very quickly after power-on.
+ CONFIG_SPLASH_SCREEN_ALIGN
+
+ If this option is set the splash image can be freely positioned
+ on the screen. Environment variable "splashpos" specifies the
+ position as "x,y". If a positive number is given it is used as
+ number of pixel from left/top. If a negative number is given it
+ is used as number of pixel from right/bottom. You can also
+ specify 'm' for centering the image.
+
+ Example:
+ setenv splashpos m,m
+ => image at center of screen
+
+ setenv splashpos 30,20
+ => image at x = 30 and y = 20
+
+ setenv splashpos -10,m
+ => vertically centered image
+ at x = dspWidth - bmpWidth - 9
+
- Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP
If this option is set, additionally to standard BMP
Defines a default value for the IP address of a TFTP
server to contact when using the "tftboot" command.
+ CONFIG_KEEP_SERVERADDR
+
+ Keeps the server's MAC address, in the env 'serveraddr'
+ for passing to bootargs (like Linux's netconsole option)
+
- Multicast TFTP Mode:
CONFIG_MCAST_TFTP
to a block boundary, and CONFIG_ENV_SIZE must be a multiple of
the NAND devices block size.
+- CONFIG_NAND_ENV_DST
+
+ Defines address in RAM to which the nand_spl code should copy the
+ environment. If redundant environment is used, it will be copied to
+ CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE.
+
- CONFIG_SYS_SPI_INIT_OFFSET
Defines offset to the initial SPI buffer area in DPRAM. The
some other boot loader or by a debugger which
performs these initializations itself.
+- CONFIG_PRELOADER
+
+ Modifies the behaviour of start.S when compiling a loader
+ that is executed before the actual U-Boot. E.g. when
+ compiling a NAND SPL.
Building the Software:
======================
list, October 2002]
-int main (int argc, char *argv[])
+int main(int argc, char *argv[])
{
sighandler_t no_more_time;
- signal (SIGALRM, no_more_time);
- alarm (PROJECT_DEADLINE - toSec (3 * WEEK));
+ signal(SIGALRM, no_more_time);
+ alarm(PROJECT_DEADLINE - toSec (3 * WEEK));
if (available_money > available_manpower) {
- pay consultant to port U-Boot;
+ Pay consultant to port U-Boot;
return 0;
}
Subscribe to u-boot mailing list;
- if (clueless) {
- email ("Hi, I am new to U-Boot, how do I get started?");
- }
+ if (clueless)
+ email("Hi, I am new to U-Boot, how do I get started?");
while (learning) {
Read the README file in the top level directory;
- Read http://www.denx.de/twiki/bin/view/DULG/Manual ;
+ Read http://www.denx.de/twiki/bin/view/DULG/Manual;
+ Read applicable doc/*.README;
Read the source, Luke;
+ /* find . -name "*.[chS]" | xargs grep -i <keyword> */
}
- if (available_money > toLocalCurrency ($2500)) {
- Buy a BDI2000;
- } else {
+ if (available_money > toLocalCurrency ($2500))
+ Buy a BDI3000;
+ else
Add a lot of aggravation and time;
- }
- Create your own board support subdirectory;
-
- Create your own board config file;
-
- while (!running) {
- do {
- Add / modify source code;
- } until (compiles);
- Debug;
- if (clueless)
- email ("Hi, I am having problems...");
+ if (a similar board exists) { /* hopefully... */
+ cp -a board/<similar> board/<myboard>
+ cp include/configs/<similar>.h include/configs/<myboard>.h
+ } else {
+ Create your own board support subdirectory;
+ Create your own board include/configs/<myboard>.h file;
+ }
+ Edit new board/<myboard> files
+ Edit new include/configs/<myboard>.h
+
+ while (!accepted) {
+ while (!running) {
+ do {
+ Add / modify source code;
+ } until (compiles);
+ Debug;
+ if (clueless)
+ email("Hi, I am having problems...");
+ }
+ Send patch file to the U-Boot email list;
+ if (reasonable critiques)
+ Incorporate improvements from email list code review;
+ else
+ Defend code as written;
}
- Send patch file to Wolfgang;
return 0;
}
projects / u-boot / blobdiff