sunxi: DT: H3: update board .dts files from Linux

[u-boot] / arch / arm / dts / sun8i-h3-orangepi-2.dts

diff --git a/arch/arm/dts/sun8i-h3-orangepi-2.dts b/arch/arm/dts/sun8i-h3-orangepi-2.dts
index d3f8f550a227a6b74982d517cc68b5b9c3a3cf50..f1fc6bdca8be711d0ba0b03fc22c551754db1f92 100644 (file)
--- a/arch/arm/dts/sun8i-h3-orangepi-2.dts
+++ b/arch/arm/dts/sun8i-h3-orangepi-2.dts
@@ -46,7 +46,6 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
 
 / {
        model = "Xunlong Orange Pi 2";
@@ -54,12 +53,26 @@
 
        aliases {
                serial0 = &uart0;
+               /* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
+               ethernet0 = &emac;
+               ethernet1 = &rtl8189;
        };
 
        chosen {
                stdout-path = "serial0:115200n8";
        };
 
+       connector {
+               compatible = "hdmi-connector";
+               type = "a";
+
+               port {
+                       hdmi_con_in: endpoint {
+                               remote-endpoint = <&hdmi_out_con>;
+                       };
+               };
+       };
+
        leds {
                compatible = "gpio-leds";
                pinctrl-names = "default";
@@ -103,10 +116,40 @@
        };
 };
 
+&codec {
+       allwinner,pa-gpios = <&pio 0 16 GPIO_ACTIVE_HIGH>; /* PA16 */
+       allwinner,audio-routing =
+               "Speaker", "LINEOUT",
+               "MIC1", "Mic",
+               "Mic",  "MBIAS";
+       status = "okay";
+};
+
+&de {
+       status = "okay";
+};
+
 &ehci1 {
        status = "okay";
 };
 
+&emac {
+       phy-handle = <&int_mii_phy>;
+       phy-mode = "mii";
+       allwinner,leds-active-low;
+       status = "okay";
+};
+
+&hdmi {
+       status = "okay";
+};
+
+&hdmi_out {
+       hdmi_out_con: endpoint {
+               remote-endpoint = <&hdmi_con_in>;
+       };
+};
+
 &ir {
        pinctrl-names = "default";
        pinctrl-0 = <&ir_pins_a>;
@@ -114,54 +157,49 @@
 };
 
 &mmc0 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
        vmmc-supply = <&reg_vcc3v3>;
        bus-width = <4>;
-       cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
-       cd-inverted;
+       cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
        status = "okay";
 };
 
 &mmc1 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&mmc1_pins_a>;
        vmmc-supply = <&reg_vcc3v3>;
        mmc-pwrseq = <&wifi_pwrseq>;
        bus-width = <4>;
        non-removable;
        status = "okay";
+
+       /*
+        * Explicitly define the sdio device, so that we can add an ethernet
+        * alias for it (which e.g. makes u-boot set a mac-address).
+        */
+       rtl8189: sdio_wifi@1 {
+               reg = <1>;
+       };
 };
 
 &pio {
-       leds_opc: led_pins@0 {
-               allwinner,pins = "PA15";
-               allwinner,function = "gpio_out";
-               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+       leds_opc: led_pins {
+               pins = "PA15";
+               function = "gpio_out";
        };
 };
 
 &r_pio {
-       leds_r_opc: led_pins@0 {
-               allwinner,pins = "PL10";
-               allwinner,function = "gpio_out";
-               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+       leds_r_opc: led_pins {
+               pins = "PL10";
+               function = "gpio_out";
        };
 
-       sw_r_opc: key_pins@0 {
-               allwinner,pins = "PL3", "PL4";
-               allwinner,function = "gpio_in";
-               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+       sw_r_opc: key_pins {
+               pins = "PL3", "PL4";
+               function = "gpio_in";
        };
 
-       wifi_pwrseq_pin_orangepi: wifi_pwrseq_pin@0 {
-               allwinner,pins = "PL7";
-               allwinner,function = "gpio_out";
-               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+       wifi_pwrseq_pin_orangepi: wifi_pwrseq_pin {
+               pins = "PL7";
+               function = "gpio_out";
        };
 };
 
@@ -176,24 +214,25 @@
        status = "okay";
 };
 
-&usb1_vbus_pin_a {
-       allwinner,pins = "PG13";
+&uart1 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&uart1_pins>;
+       status = "disabled";
 };
 
-&usbphy {
-       usb1_vbus-supply = <&reg_usb1_vbus>;
-       status = "okay";
+&uart2 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&uart2_pins>;
+       status = "disabled";
 };
 
-&emac {
+&uart3 {
        pinctrl-names = "default";
-       pinctrl-0 = <&rgmii_pins>;
-       phy-mode = "rgmii";
-       phy = <&phy1>;
-       status = "okay";
-
-       phy1: ethernet-phy@1 {
-               reg = <1>;
-       };
+       pinctrl-0 = <&uart3_pins>;
+       status = "disabled";
 };
 
+&usbphy {
+       usb1_vbus-supply = <&reg_usb1_vbus>;
+       status = "okay";
+};