#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Xunlong Orange Pi 2";
aliases {
serial0 = &uart0;
+ /* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
+ ethernet0 = &emac;
+ ethernet1 = &rtl8189;
};
chosen {
stdout-path = "serial0:115200n8";
};
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
};
};
+&codec {
+ allwinner,pa-gpios = <&pio 0 16 GPIO_ACTIVE_HIGH>; /* PA16 */
+ allwinner,audio-routing =
+ "Speaker", "LINEOUT",
+ "MIC1", "Mic",
+ "Mic", "MBIAS";
+ status = "okay";
+};
+
+&de {
+ status = "okay";
+};
+
&ehci1 {
status = "okay";
};
+&emac {
+ phy-handle = <&int_mii_phy>;
+ phy-mode = "mii";
+ allwinner,leds-active-low;
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&ir {
pinctrl-names = "default";
pinctrl-0 = <&ir_pins_a>;
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
- cd-inverted;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
status = "okay";
};
&mmc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins_a>;
vmmc-supply = <®_vcc3v3>;
mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
non-removable;
status = "okay";
+
+ /*
+ * Explicitly define the sdio device, so that we can add an ethernet
+ * alias for it (which e.g. makes u-boot set a mac-address).
+ */
+ rtl8189: sdio_wifi@1 {
+ reg = <1>;
+ };
};
&pio {
- leds_opc: led_pins@0 {
- allwinner,pins = "PA15";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ leds_opc: led_pins {
+ pins = "PA15";
+ function = "gpio_out";
};
};
&r_pio {
- leds_r_opc: led_pins@0 {
- allwinner,pins = "PL10";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ leds_r_opc: led_pins {
+ pins = "PL10";
+ function = "gpio_out";
};
- sw_r_opc: key_pins@0 {
- allwinner,pins = "PL3", "PL4";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ sw_r_opc: key_pins {
+ pins = "PL3", "PL4";
+ function = "gpio_in";
};
- wifi_pwrseq_pin_orangepi: wifi_pwrseq_pin@0 {
- allwinner,pins = "PL7";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ wifi_pwrseq_pin_orangepi: wifi_pwrseq_pin {
+ pins = "PL7";
+ function = "gpio_out";
};
};
status = "okay";
};
-&usb1_vbus_pin_a {
- allwinner,pins = "PG13";
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
};
-&usbphy {
- usb1_vbus-supply = <®_usb1_vbus>;
- status = "okay";
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
};
-&emac {
+&uart3 {
pinctrl-names = "default";
- pinctrl-0 = <&rgmii_pins>;
- phy-mode = "rgmii";
- phy = <&phy1>;
- status = "okay";
-
- phy1: ethernet-phy@1 {
- reg = <1>;
- };
+ pinctrl-0 = <&uart3_pins>;
+ status = "disabled";
};
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};