endmenu
-source "cmd/fastboot/Kconfig"
-
config BUILD_BIN2C
bool
config CMD_BOOTEFI_HELLO_COMPILE
bool "Compile a standard EFI hello world binary for testing"
- depends on CMD_BOOTEFI && (ARM || X86)
+ depends on CMD_BOOTEFI && (ARM || X86 || RISCV)
default y
help
This compiles a standard EFI hello world application with U-Boot so
help
Simple RAM read/write test.
+if CMD_MEMTEST
+
+config SYS_ALT_MEMTEST
+ bool "Alternative test"
+ help
+ Use a more complete alternative memory test.
+
+endif
+
config CMD_MX_CYCLIC
bool "mdc, mwc"
help
help
ARM Ltd reference designs flash partition access
+config CMD_ADC
+ bool "adc - Access Analog to Digital Converters info and data"
+ select ADC
+ select DM_REGULATOR
+ help
+ Shows ADC device info and permit printing one-shot analog converted
+ data from a named Analog to Digital Converter.
+
config CMD_CLK
bool "clk - Show clock frequencies"
help
can be useful to see the state of driver model for debugging or
interest.
+config CMD_FASTBOOT
+ bool "fastboot - Android fastboot support"
+ depends on FASTBOOT
+ help
+ This enables the command "fastboot" which enables the Android
+ fastboot mode for the platform. Fastboot is a protocol for
+ downloading images, flashing and device control used on
+ Android devices. Fastboot requires either the network stack
+ enabled or support for acting as a USB device.
+
+ See doc/README.android-fastboot for more information.
+
config CMD_FDC
bool "fdcboot - Boot from floppy device"
help
Supports loading an FPGA device from a bitstream buffer containing
a partial bitstream.
+config CMD_FPGA_LOAD_SECURE
+ bool "fpga loads - loads secure bitstreams (Xilinx only)"
+ depends on CMD_FPGA
+ help
+ Enables the fpga loads command which is used to load secure
+ (authenticated or encrypted or both) bitstreams on to FPGA.
+
config CMD_FPGAD
bool "fpgad - dump FPGA registers"
help
help
MMC memory mapped support.
+config CMD_MMC_RPMB
+ bool "Enable support for RPMB in the mmc command"
+ depends on CMD_MMC
+ help
+ Enable the commands for reading, writing and programming the
+ key for the Replay Protection Memory Block partition in eMMC.
+
+config CMD_MMC_SWRITE
+ bool "mmc swrite"
+ depends on CMD_MMC && MMC_WRITE
+ select IMAGE_SPARSE
+ help
+ Enable support for the "mmc swrite" command to write Android sparse
+ images to eMMC.
+
config CMD_NAND
bool "nand"
default y if NAND_SUNXI
endmenu
-menu "Network commands"
-
if NET
-config CMD_NET
- bool "bootp, tftpboot"
+menuconfig CMD_NET
+ bool "Network commands"
+ default y
+
+if CMD_NET
+
+config CMD_BOOTP
+ bool "bootp"
default y
help
- Network commands.
bootp - boot image via network using BOOTP/TFTP protocol
+
+config CMD_DHCP
+ bool "dhcp"
+ depends on CMD_BOOTP
+ help
+ Boot image via network using DHCP/TFTP protocol
+
+config BOOTP_BOOTPATH
+ bool "Request & store 'rootpath' from BOOTP/DHCP server"
+ default y
+ depends on CMD_BOOTP
+ help
+ Even though the config is called BOOTP_BOOTPATH, it stores the
+ path in the variable 'rootpath'.
+
+config BOOTP_DNS
+ bool "Request & store 'dnsip' from BOOTP/DHCP server"
+ default y
+ depends on CMD_BOOTP
+ help
+ The primary DNS server is stored as 'dnsip'. If two servers are
+ returned, you must set BOOTP_DNS2 to store that second server IP
+ also.
+
+config BOOTP_DNS2
+ bool "Store 'dnsip2' from BOOTP/DHCP server"
+ depends on BOOTP_DNS
+ help
+ If a DHCP client requests the DNS server IP from a DHCP server,
+ it is possible that more than one DNS serverip is offered to the
+ client. If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
+ server IP will be stored in the additional environment
+ variable "dnsip2". The first DNS serverip is always
+ stored in the variable "dnsip", when BOOTP_DNS is defined.
+
+config BOOTP_GATEWAY
+ bool "Request & store 'gatewayip' from BOOTP/DHCP server"
+ default y
+ depends on CMD_BOOTP
+
+config BOOTP_HOSTNAME
+ bool "Request & store 'hostname' from BOOTP/DHCP server"
+ default y
+ depends on CMD_BOOTP
+ help
+ The name may or may not be qualified with the local domain name.
+
+config BOOTP_PREFER_SERVERIP
+ bool "serverip variable takes precedent over DHCP server IP."
+ depends on CMD_BOOTP
+ help
+ By default a BOOTP/DHCP reply will overwrite the 'serverip' variable.
+
+ With this option enabled, the 'serverip' variable in the environment
+ takes precedence over DHCP server IP and will only be set by the DHCP
+ server if not already set in the environment.
+
+config BOOTP_SUBNETMASK
+ bool "Request & store 'netmask' from BOOTP/DHCP server"
+ default y
+ depends on CMD_BOOTP
+
+config BOOTP_NTPSERVER
+ bool "Request & store 'ntpserverip' from BOOTP/DHCP server"
+ depends on CMD_BOOTP
+
+config BOOTP_PXE
+ bool "Send PXE client arch to BOOTP/DHCP server"
+ default y
+ depends on CMD_BOOTP && CMD_PXE
+ help
+ Supported for ARM, ARM64, and x86 for now.
+
+config BOOTP_PXE_CLIENTARCH
+ hex
+ depends on BOOTP_PXE
+ default 0x16 if ARM64
+ default 0x15 if ARM
+ default 0 if X86
+
+config BOOTP_VCI_STRING
+ string
+ depends on CMD_BOOTP
+ default "U-Boot.armv7" if CPU_V7A || CPU_V7M || CPU_V7R
+ default "U-Boot.armv8" if ARM64
+ default "U-Boot.arm" if ARM
+ default "U-Boot"
+
+config CMD_TFTPBOOT
+ bool "tftpboot"
+ default y
+ help
tftpboot - boot image via network using TFTP protocol
config CMD_TFTPPUT
bool "tftp put"
+ depends on CMD_TFTPBOOT
help
TFTP put command, for uploading files to a server
config CMD_TFTPSRV
bool "tftpsrv"
+ depends on CMD_TFTPBOOT
help
Act as a TFTP server and boot the first received file
+config NET_TFTP_VARS
+ bool "Control TFTP timeout and count through environment"
+ depends on CMD_TFTPBOOT
+ default y
+ help
+ If set, allows controlling the TFTP timeout through the
+ environment variable tftptimeout, and the TFTP maximum
+ timeout count through the variable tftptimeoutcountmax.
+ If unset, timeout and maximum are hard-defined as 1 second
+ and 10 timouts per TFTP transfer.
+
config CMD_RARP
bool "rarpboot"
help
Boot image via network using RARP/TFTP protocol
-config CMD_DHCP
- bool "dhcp"
- depends on CMD_NET
- help
- Boot image via network using DHCP/TFTP protocol
-
-config CMD_PXE
- bool "pxe"
- depends on CMD_NET
- select MENU
- help
- Boot image via network using PXE protocol
-
config CMD_NFS
bool "nfs"
default y
config CMD_LINK_LOCAL
bool "linklocal"
+ select LIB_RAND
help
Acquire a network IP address using the link-local protocol
+endif
+
config CMD_ETHSW
bool "ethsw"
help
operations such as enabling / disabling a port and
viewing/maintaining the filtering database (FDB)
-endif
+config CMD_PXE
+ bool "pxe"
+ select MENU
+ help
+ Boot image via network using PXE protocol
-endmenu
+config CMD_WOL
+ bool "wol"
+ help
+ Wait for wake-on-lan Magic Packet
+
+endif
menu "Misc commands"
the image into RAM, then using this command to look at it or display
it.
+config CMD_BOOTCOUNT
+ bool "bootcount"
+ depends on BOOTCOUNT_LIMIT
+ help
+ Enable the bootcount command, which allows interrogation and
+ reset of the bootcounter.
+
config CMD_BSP
bool "Enable board-specific commands"
help
help
Delay execution for some time
+config MP
+ bool "support for multiprocessor"
+ help
+ This provides an option to brinup
+ different processors in multiprocessor
+ cases.
+
config CMD_TIMER
bool "timer"
help
saved to memory or to an environment variable. It is also possible
to verify a hash against data in memory.
+config CMD_HVC
+ bool "Support the 'hvc' command"
+ depends on ARM_SMCCC
+ help
+ Allows issuing Hypervisor Calls (HVCs). Mostly useful for
+ development and testing.
+
+config CMD_SMC
+ bool "Support the 'smc' command"
+ depends on ARM_SMCCC
+ help
+ Allows issuing Secure Monitor Calls (SMCs). Mostly useful for
+ development and testing.
+
config HASH_VERIFY
bool "hash -v"
depends on CMD_HASH
help
Add -v option to verify data against a hash.
+config CMD_TPM_V1
+ bool
+
+config CMD_TPM_V2
+ bool
+
config CMD_TPM
bool "Enable the 'tpm' command"
- depends on TPM
+ depends on TPM_V1 || TPM_V2
+ select CMD_TPM_V1 if TPM_V1
+ select CMD_TPM_V2 if TPM_V2
help
This provides a means to talk to a TPM from the command line. A wide
range of commands if provided - see 'tpm help' for details. The
command requires a suitable TPM on your board and the correct driver
must be enabled.
+if CMD_TPM
+
config CMD_TPM_TEST
bool "Enable the 'tpm test' command"
- depends on CMD_TPM
+ depends on TPM_V1
help
- This provides a a series of tests to confirm that the TPM is working
- correctly. The tests cover initialisation, non-volatile RAM, extend,
- global lock and checking that timing is within expectations. The
- tests pass correctly on Infineon TPMs but may need to be adjusted
+ This provides a a series of tests to confirm that the TPMv1.x is
+ working correctly. The tests cover initialisation, non-volatile RAM,
+ extend, global lock and checking that timing is within expectations.
+ The tests pass correctly on Infineon TPMs but may need to be adjusted
for other devices.
+endif
+
endmenu
menu "Firmware commands"
config CMD_LOG
bool "log - Generation, control and access to logging"
+ select LOG
help
This provides access to logging features. It allows the output of
log data to be controlled to a limited extent (setting up the default
for analsys (e.g. using bootchart). See doc/README.trace for full
details.
+config CMD_AVB
+ bool "avb - Android Verified Boot 2.0 operations"
+ depends on LIBAVB
+ default n
+ help
+ Enables a "avb" command to perform verification of partitions using
+ Android Verified Boot 2.0 functionality. It includes such subcommands:
+ avb init - initialize avb2 subsystem
+ avb read_rb - read rollback index
+ avb write_rb - write rollback index
+ avb is_unlocked - check device lock state
+ avb get_uuid - read and print uuid of a partition
+ avb read_part - read data from partition
+ avb read_part_hex - read data from partition and output to stdout
+ avb write_part - write data to partition
+ avb verify - run full verification chain
endmenu
config CMD_UBI
projects / u-boot / blobdiff