+/* SPDX-License-Identifier: GPL-2.0 */
/*
* Copyright 2007-2011 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0
*/
/*
#define __CONFIG_H
/* High Level Configuration Options */
-#define CONFIG_MPC8610 1 /* MPC8610 specific */
-#define CONFIG_MPC8610HPCD 1 /* MPC8610HPCD board specific */
#define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */
-#define CONFIG_SYS_TEXT_BASE 0xfff00000
-
/* video */
#define CONFIG_FSL_DIU_FB
#ifdef CONFIG_FSL_DIU_FB
#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR + 0x2c000)
-#define CONFIG_VIDEO
-#define CONFIG_CMD_BMP
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VIDEO_SW_CURSOR
-#define CONFIG_VGA_AS_SINGLE_DEVICE
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_LOGO
#endif
*/
#define CONFIG_SYS_SCRATCH_VA 0xc0000000
-#define CONFIG_PCI 1 /* Enable PCI/PCIE*/
#define CONFIG_PCI1 1 /* PCI controller 1 */
#define CONFIG_PCIE1 1 /* PCIe 1 connected to ULI bridge */
#define CONFIG_PCIE2 1 /* PCIe 2 connected to slot */
#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
-#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */
#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
#endif
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
#define CONFIG_MISC_INIT_R 1
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
-#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR_PHYS_LOW
/* DDR Setup */
-#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD for DDR */
#define CONFIG_DDR_SPD
#define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */
#define CONFIG_VERY_BIG_RAM
-#define CONFIG_NUM_DDR_CONTROLLERS 1
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
#define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) /* Reserved for malloc */
/* Serial Port */
-#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-#define CONFIG_CMD_REGINFO
-
#define CONFIG_ULI526X
-#ifdef CONFIG_ULI526X
-#endif
/************************************************************
* USB support
************************************************************/
#define CONFIG_PCI_OHCI 1
#define CONFIG_USB_OHCI_NEW 1
-#define CONFIG_USB_KEYBOARD 1
-#define CONFIG_SYS_STDIO_DEREGISTER
-#define CONFIG_SYS_USB_EVENT_POLL 1
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci"
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1
#define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
#endif
-#define CONFIG_DOS_PARTITION
-#define CONFIG_SCSI_AHCI
-
#ifdef CONFIG_SCSI_AHCI
-#define CONFIG_LIBATA
#define CONFIG_SATA_ULI5288
#define CONFIG_SYS_SCSI_MAX_SCSI_ID 4
#define CONFIG_SYS_SCSI_MAX_LUN 1
* Environment
*/
#ifndef CONFIG_SYS_RAMBOOT
-#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 126k (one sector) for env */
#define CONFIG_ENV_SIZE 0x2000
#else
-#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
#define CONFIG_ENV_SIZE 0x2000
#endif
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
-#if defined(CONFIG_PCI)
-#define CONFIG_CMD_PCI
-#define CONFIG_SCSI
-#endif
-
#define CONFIG_WATCHDOG /* watchdog enabled */
#define CONFIG_SYS_WATCHDOG_FREQ 5000 /* Feed interval, 5s */
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING /* Command-line editing */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
*/
#define CONFIG_IPADDR 192.168.1.100
-#define CONFIG_HOSTNAME unknown
+#define CONFIG_HOSTNAME "unknown"
#define CONFIG_ROOTPATH "/opt/nfsroot"
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_UBOOTPATH 8610hpcd/u-boot.bin
/* default location for tftp and bootm */
#define CONFIG_LOADADDR 0x10000000
-#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
-
-#define CONFIG_BAUDRATE 115200
-
#if defined(CONFIG_PCI1)
#define PCI_ENV \
"pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \
projects / u-boot / blobdiff