+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2013-2015 Arcturus Networks, Inc.
* http://www.arcturusnetworks.com/products/ucp1020/
* based on include/configs/p1_p2_rdb_pc.h
* original copyright follows:
* Copyright 2009-2011 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
/*
#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_FSL_ELBC
#define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */
#define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */
#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
#define CONFIG_BOARDNAME "uCP1020-64EE512-0U1-XR-T1"
-#define CONFIG_TSEC_ENET
#define CONFIG_TSEC1
#define CONFIG_TSEC3
#define CONFIG_HAS_ETH0
#define CONFIG_NETMASK 255.255.252.0
#define CONFIG_ETHPRIME "eTSEC3"
-#ifndef CONFIG_SPI_FLASH
-#endif
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
#define CONFIG_SYS_L2_SIZE (256 << 10)
-#define CONFIG_LAST_STAGE_INIT
-
#endif
#if defined(CONFIG_TARGET_UCP1020)
#define CONFIG_BOARDNAME_LOCAL "uCP1020-64EEE512-OU1-XR"
-#define CONFIG_TSEC_ENET
#define CONFIG_TSEC1
#define CONFIG_TSEC2
#define CONFIG_TSEC3
#define CONFIG_NETMASK 255.255.255.0
#define CONFIG_ETHPRIME "eTSEC1"
-#ifndef CONFIG_SPI_FLASH
-#endif
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
#define CONFIG_SYS_L2_SIZE (256 << 10)
-#define CONFIG_LAST_STAGE_INIT
-
#endif
#ifdef CONFIG_SDCARD
#define CONFIG_RAMBOOT_SDCARD
#define CONFIG_SYS_RAMBOOT
#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_SYS_TEXT_BASE 0x11000000
#define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc
#endif
#define CONFIG_RAMBOOT_SPIFLASH
#define CONFIG_SYS_RAMBOOT
#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_SYS_TEXT_BASE 0x11000000
#define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc
#endif
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE 0xeff80000
-#endif
#define CONFIG_SYS_TEXT_BASE_NOR 0xeff80000
#ifndef CONFIG_RESET_VECTOR_ADDRESS
#define CONFIG_ENV_OVERWRITE
-#define CONFIG_CMD_SATA
-#define CONFIG_SATA_SIL
#define CONFIG_SYS_SATA_MAX_DEVICE 2
-#define CONFIG_LIBATA
#define CONFIG_LBA48
#define CONFIG_SYS_CLK_FREQ 66666666
#define CONFIG_HWCONFIG
-#define CONFIG_DTT_ADM1021 1 /* ADM1021 temp sensor support */
-#define CONFIG_SYS_DTT_BUS_NUM 1 /* The I2C bus for DTT */
-#define CONFIG_DTT_SENSORS { 0, 1 } /* Sensor index */
-/*
- * ADM1021/NCT72 temp sensor configuration (see dtt/adm1021.c for details).
- * there will be one entry in this array for each two (dummy) sensors in
- * CONFIG_DTT_SENSORS.
- *
- * For uCP1020 module:
- * - only one ADM1021/NCT72
- * - i2c addr 0x41
- * - conversion rate 0x02 = 0.25 conversions/second
- * - ALERT output disabled
- * - local temp sensor enabled, min set to 0 deg, max set to 85 deg
- * - remote temp sensor enabled, min set to 0 deg, max set to 85 deg
- */
-#define CONFIG_SYS_DTT_ADM1021 { { CONFIG_SYS_I2C_NCT72_ADDR, \
- 0x02, 0, 1, 0, 85, 1, 0, 85} }
-
-#define CONFIG_CMD_DTT
-
/*
* These can be toggled for performance analysis, otherwise use default.
*/
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x1fffffff
-#define CONFIG_PANIC_HANG /* do not reset board on panic */
#define CONFIG_SYS_CCSRBAR 0xffe00000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
-
#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */
/* Initial L1 address */
* open - index 2
* shorted - index 1
*/
-#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_SPD_BUS_NUM 1 /* For rom_loc and flash bank */
#define CONFIG_RTC_DS1337
-#define CONFIG_SYS_RTC_DS1337_NOOSC
+#define CONFIG_RTC_DS1337_NOOSC
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
#define CONFIG_SYS_I2C_PCA9557_ADDR 0x18
#define CONFIG_SYS_I2C_NCT72_ADDR 0x4C
#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc00000
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
-#define CONFIG_CMD_PCI
-
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#endif /* CONFIG_PCI */
*/
#ifdef CONFIG_ENV_FIT_UCBOOT
-#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x20000)
#define CONFIG_ENV_SIZE 0x20000
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
#ifdef CONFIG_RAMBOOT_SPIFLASH
-#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SIZE 0x3000 /* 12KB */
#define CONFIG_ENV_OFFSET 0x2000 /* 8KB */
#define CONFIG_ENV_SECT_SIZE 0x1000
#endif
#elif defined(CONFIG_RAMBOOT_SDCARD)
-#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_FSL_FIXED_MMC_LOCATION
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_SYS_MMC_ENV_DEV 0
#elif defined(CONFIG_SYS_RAMBOOT)
-#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
#define CONFIG_ENV_SIZE 0x2000
#else
-#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_BASE (CONFIG_SYS_FLASH_BASE)
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
#define CONFIG_LOADS_ECHO /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_ERRATA
-#define CONFIG_CMD_CRAMFS
-
/*
* USB
*/
#define CONFIG_HAS_FSL_DR_USB
#if defined(CONFIG_HAS_FSL_DR_USB)
-#define CONFIG_USB_EHCI
-
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#endif
#undef CONFIG_WATCHDOG /* watchdog disabled */
#ifdef CONFIG_MMC
-#define CONFIG_FSL_ESDHC
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
#define CONFIG_MMC_SPI
-#define CONFIG_CMD_MMC_SPI
-#define CONFIG_GENERIC_MMC
#endif
/* Misc Extra Settings */
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING /* Command-line editing */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
- /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms tick */
/*
#if defined(CONFIG_TSEC_ENET)
-#if defined(CONFIG_UCP1020_REV_1_2)
-#define CONFIG_PHY_MICREL_KSZ9021
-#elif defined(CONFIG_UCP1020_REV_1_3)
-#define CONFIG_PHY_MICREL_KSZ9031
+#if defined(CONFIG_UCP1020_REV_1_2) || defined(CONFIG_UCP1020_REV_1_3)
#else
#error "UCP1020 module revision is not defined !!!"
#endif
#define TSEC2_PHYIDX 0
#define TSEC3_PHYIDX 0
-#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
-
#endif
-#define CONFIG_HOSTNAME UCP1020
+#define CONFIG_HOSTNAME "UCP1020"
#define CONFIG_ROOTPATH "/opt/nfsroot"
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
/* default location for tftp and bootm */
#define CONFIG_LOADADDR 1000000
-#define CONFIG_BOOTARGS /* the boot command will set bootargs */
-
-#define CONFIG_BAUDRATE 115200
-
#if defined(CONFIG_DONGLE)
#define CONFIG_EXTRA_ENV_SETTINGS \
projects / u-boot / blobdiff