+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2011 Logic Product Development <www.logicpd.com>
* Peter Barada <peter.barada@logicpd.com>
*
* Configuration settings for the Logic OMAP35x/DM37x SOM LV/Torpedo
* reference boards.
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
-/*
- * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
- * 64 bytes before this address should be set aside for u-boot.img's
- * header. That is 0x800FFFC0--0x80100000 should not be used for any
- * other needs. We use this rather than the inherited defines from
- * ti_armv7_common.h for backwards compatibility.
- */
-#define CONFIG_SYS_TEXT_BASE 0x80100000
-#define CONFIG_SPL_BSS_START_ADDR 0x80000000
-#define CONFIG_SPL_BSS_MAX_SIZE (512 << 10) /* 512 KB */
-#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
-#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
-
#include <configs/ti_omap3_common.h>
+#ifdef CONFIG_SPL_BUILD
+/* select serial console configuration for SPL */
+#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1
+#endif
+
+
/*
* We are only ever GP parts and will utilize all of the "downloaded image"
* area in SRAM which starts at 0x40200000 and ends at 0x4020FFFF (64KB) in
#undef CONFIG_SPL_TEXT_BASE
#define CONFIG_SPL_TEXT_BASE 0x40200000
-#define CONFIG_BOARD_LATE_INIT
#define CONFIG_MISC_INIT_R /* misc_init_r dumps the die id */
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_REVISION_TAG
-#define CONFIG_CMDLINE_EDITING /* cmd line edit/history */
/* Hardware drivers */
-/* GPIO banks */
-#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */
-
-#define CONFIG_USB_OMAP3
-
-/* select serial console configuration */
-#undef CONFIG_CONS_INDEX
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1
-#define CONFIG_SERIAL1 1 /* UART1 on OMAP Logic boards */
-
-/* commands to include */
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_CMD_NAND_LOCK_UNLOCK /* nand (un)lock commands */
-
/* I2C */
-#define CONFIG_SYS_I2C_OMAP34XX
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM AT24C64 */
-#define EXPANSION_EEPROM_I2C_BUS 2 /* I2C Bus for AT24C64 */
-#define CONFIG_OMAP3_LOGIC_USE_NEW_PRODUCT_ID
-
-/* USB */
-#define CONFIG_USB_MUSB_OMAP2PLUS
-#define CONFIG_USB_MUSB_PIO_ONLY
-#define CONFIG_USB_ETHER
-#define CONFIG_USB_ETHER_RNDIS
-#define CONFIG_USB_FUNCTION_FASTBOOT
-#define CONFIG_CMD_FASTBOOT
-#define CONFIG_ANDROID_BOOT_IMAGE
-#define CONFIG_FASTBOOT_BUF_ADDR CONFIG_SYS_LOAD_ADDR
-#define CONFIG_FASTBOOT_BUF_SIZE 0x07000000
-
-/* TWL4030 */
-#define CONFIG_TWL4030_PWM
-#define CONFIG_TWL4030_USB
/* Board NAND Info. */
#ifdef CONFIG_NAND
-#define CONFIG_NAND_OMAP_GPMC
-
-#define CONFIG_CMD_UBIFS /* Read-only UBI volume operations */
-#define CONFIG_RBTREE /* required by CONFIG_CMD_UBI */
-#define CONFIG_LZO /* required by CONFIG_CMD_UBIFS */
-
#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
/* to access nand */
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */
/* NAND devices */
-#define CONFIG_SYS_NAND_BUSWIDTH_16BIT
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 13
#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
-#define CONFIG_BCH
#define CONFIG_SYS_NAND_MAX_OOBFREE 2
#define CONFIG_SYS_NAND_MAX_ECCPOS 56
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
#define CONFIG_MTD_PARTITIONS /* required for UBI partition support */
-#define MTDIDS_DEFAULT "nand0=omap2-nand.0"
-#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:512k(MLO),"\
- "1920k(u-boot),128k(u-boot-env),"\
- "4m(kernel),-(fs)"
#endif
/* Environment information */
-/*
- * PREBOOT assumes the 4.3" display is attached. User can interrupt
- * and modify display variable to suit their needs.
- */
#define CONFIG_PREBOOT \
- "echo ======================NOTICE============================;"\
- "echo \"The u-boot environment is not set.\";" \
- "echo \"If using a display a valid display variable for your panel\";" \
- "echo \"needs to be set.\";" \
- "echo \"Valid display options are:\";" \
- "echo \" 2 == LQ121S1DG31 TFT SVGA (12.1) Sharp\";" \
- "echo \" 3 == LQ036Q1DA01 TFT QVGA (3.6) Sharp w/ASIC\";" \
- "echo \" 5 == LQ064D343 TFT VGA (6.4) Sharp\";" \
- "echo \" 7 == LQ10D368 TFT VGA (10.4) Sharp\";" \
- "echo \" 15 == LQ043T1DG01 TFT WQVGA (4.3) Sharp (DEFAULT)\";" \
- "echo \" vga[-dvi or -hdmi] LCD VGA 640x480\";" \
- "echo \" svga[-dvi or -hdmi] LCD SVGA 800x600\";" \
- "echo \" xga[-dvi or -hdmi] LCD XGA 1024x768\";" \
- "echo \" 720p[-dvi or -hdmi] LCD 720P 1280x720\";" \
- "echo \"Defaulting to 4.3 LCD panel (display=15).\";" \
- "setenv display 15;" \
"setenv preboot;" \
- "nand unlock;" \
"saveenv;"
#define CONFIG_EXTRA_ENV_SETTINGS \
- "loadaddr=0x81000000\0" \
- "uimage=uImage\0" \
- "zimage=zImage\0" \
- "mtdids=" MTDIDS_DEFAULT "\0" \
- "mtdparts=" MTDPARTS_DEFAULT "\0" \
+ DEFAULT_LINUX_BOOT_ENV \
+ "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
+ "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
"mmcdev=0\0" \
"mmcroot=/dev/mmcblk0p2 rw\0" \
"mmcrootfstype=ext4 rootwait\0" \
"fi; " \
"else run defaultboot; fi\0" \
"defaultboot=run mmcramboot\0" \
- "consoledevice=ttyO0\0" \
- "display=15\0" \
+ "consoledevice=ttyS0\0" \
"setconsole=setenv console ${consoledevice},${baudrate}n8\0" \
"dump_bootargs=echo 'Bootargs: '; echo $bootargs\0" \
"rotation=0\0" \
"omapfb.rotate=${rotation}; " \
"fi\0" \
"optargs=ignore_loglevel early_printk no_console_suspend\0" \
- "addmtdparts=setenv bootargs ${bootargs} ${mtdparts}\0" \
- "common_bootargs=setenv bootargs ${bootargs} display=${display} " \
- "${optargs};" \
- "run addmtdparts; " \
+ "common_bootargs=run setconsole; setenv bootargs " \
+ "${bootargs} "\
+ "console=${console} " \
+ "${mtdparts} "\
+ "${optargs}; " \
"run vrfb_arg\0" \
- "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
+ "loadbootscript=load mmc ${mmcdev} ${loadaddr} boot.scr\0" \
"bootscript=echo 'Running bootscript from mmc ...'; " \
"source ${loadaddr}\0" \
- "loaduimage=mmc rescan; " \
- "fatload mmc ${mmcdev} ${loadaddr} ${uimage}\0" \
- "loadzimage=mmc rescan; " \
- "fatload mmc ${mmcdev} ${loadaddr} ${zimage}\0" \
+ "loadimage=mmc rescan; " \
+ "load mmc ${mmcdev} ${loadaddr} ${bootfile}\0" \
"ramdisksize=64000\0" \
- "ramdiskaddr=0x82000000\0" \
"ramdiskimage=rootfs.ext2.gz.uboot\0" \
"loadramdisk=mmc rescan; " \
- "fatload mmc ${mmcdev} ${ramdiskaddr} ${ramdiskimage}\0" \
- "ramargs=run setconsole; setenv bootargs console=${console} " \
+ "load mmc ${mmcdev} ${rdaddr} ${ramdiskimage}\0" \
+ "ramargs=setenv bootargs "\
"root=/dev/ram rw ramdisk_size=${ramdisksize}\0" \
- "mmcargs=run setconsole; setenv bootargs console=${console} " \
- "${optargs} " \
- "root=${mmcroot} " \
- "rootfstype=${mmcrootfstype}\0" \
- "nandargs=run setconsole; setenv bootargs console=${console} " \
- "${optargs} " \
+ "mmcargs=setenv bootargs "\
+ "root=${mmcroot} rootfstype=${mmcrootfstype}\0" \
+ "nandargs=setenv bootargs "\
"root=${nandroot} " \
"rootfstype=${nandrootfstype}\0" \
- "fdtaddr=0x86000000\0" \
- "loadfdtimage=mmc rescan; " \
- "fatload mmc ${mmcdev} ${fdtaddr} ${fdtimage}\0" \
- "mmcbootz=echo Booting with DT from mmc${mmcdev} ...; " \
+ "nfsargs=setenv serverip ${tftpserver}; " \
+ "setenv bootargs root=/dev/nfs " \
+ "nfsroot=${nfsrootpath} " \
+ "ip=${ipaddr}:${tftpserver}:${gatewayip}:${netmask}::eth0:off\0" \
+ "nfsrootpath=/opt/nfs-exports/omap\0" \
+ "autoload=no\0" \
+ "loadfdt=mmc rescan; " \
+ "load mmc ${mmcdev} ${fdtaddr} ${fdtimage}\0" \
+ "mmcbootcommon=echo Booting with DT from mmc${mmcdev} ...; " \
"run mmcargs; " \
"run common_bootargs; " \
"run dump_bootargs; " \
- "run loadzimage; " \
- "run loadfdtimage; " \
+ "run loadimage; " \
+ "run loadfdt;\0 " \
+ "mmcbootz=setenv bootfile zImage; " \
+ "run mmcbootcommon; "\
"bootz ${loadaddr} - ${fdtaddr}\0" \
- "mmcramboot=echo 'Booting uImage kernel from mmc w/ramdisk...'; " \
+ "mmcboot=setenv bootfile uImage; "\
+ "run mmcbootcommon; "\
+ "bootm ${loadaddr} - ${fdtaddr}\0" \
+ "mmcrambootcommon=echo 'Booting kernel from MMC w/ramdisk...'; " \
"run ramargs; " \
"run common_bootargs; " \
"run dump_bootargs; " \
- "run loaduimage; " \
- "run loadramdisk; " \
- "bootm ${loadaddr} ${ramdiskaddr}\0" \
- "mmcrambootz=echo 'Booting zImage kernel from mmc w/ramdisk...'; " \
- "run ramargs; " \
- "run common_bootargs; " \
- "run dump_bootargs; " \
- "run loadzimage; " \
- "run loadramdisk; " \
- "run loadfdtimage; " \
- "bootz ${loadaddr} ${ramdiskaddr} ${fdtaddr}\0; " \
+ "run loadimage; " \
+ "run loadfdt; " \
+ "run loadramdisk\0" \
+ "mmcramboot=setenv bootfile uImage; " \
+ "run mmcrambootcommon; " \
+ "bootm ${loadaddr} ${rdaddr} ${fdtaddr}\0" \
+ "mmcrambootz=setenv bootfile zImage; " \
+ "run mmcrambootcommon; " \
+ "bootz ${loadaddr} ${rdaddr} ${fdtaddr}\0" \
"tftpboot=echo 'Booting kernel/ramdisk rootfs from tftp...'; " \
"run ramargs; " \
"run common_bootargs; " \
"run dump_bootargs; " \
- "tftpboot ${loadaddr} ${uimage}; " \
- "tftpboot ${ramdiskaddr} ${ramdiskimage}; " \
- "bootm ${loadaddr} ${ramdiskaddr}\0"
+ "tftpboot ${loadaddr} ${zimage}; " \
+ "tftpboot ${rdaddr} ${ramdiskimage}; " \
+ "bootm ${loadaddr} ${rdaddr}\0" \
+ "tftpbootz=echo 'Booting kernel NFS rootfs...'; " \
+ "dhcp;" \
+ "run nfsargs;" \
+ "run common_bootargs;" \
+ "run dump_bootargs;" \
+ "tftpboot $loadaddr zImage;" \
+ "bootz $loadaddr\0" \
+ "nandbootcommon=echo 'Booting kernel from NAND...';" \
+ "run nandargs;" \
+ "run common_bootargs;" \
+ "run dump_bootargs;" \
+ "nand read ${loadaddr} kernel;" \
+ "nand read ${fdtaddr} spl-os;\0" \
+ "nandbootz=run nandbootcommon; "\
+ "bootz ${loadaddr} - ${fdtaddr}\0"\
+ "nandboot=run nandbootcommon; "\
+ "bootm ${loadaddr} - ${fdtaddr}\0"\
#define CONFIG_BOOTCOMMAND \
"run autoboot"
/* Miscellaneous configurable options */
-#define CONFIG_AUTO_COMPLETE
/* memtest works on */
#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
/* **** PISMO SUPPORT *** */
#if defined(CONFIG_CMD_NAND)
#define CONFIG_SYS_FLASH_BASE NAND_BASE
-#elif defined(CONFIG_CMD_ONENAND)
-#define CONFIG_SYS_FLASH_BASE ONENAND_MAP
#endif
/* Monitor at start of flash */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_ENV_IS_IN_NAND 1
#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
-#define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */
-#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
-#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
-#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
-
-/* SMSC922x Ethernet */
-#if defined(CONFIG_CMD_NET)
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_32_BIT
-#define CONFIG_SMC911X_BASE 0x08000000
-#endif /* (CONFIG_CMD_NET) */
+#define CONFIG_ENV_OFFSET 0x260000
+#define CONFIG_ENV_ADDR 0x260000
/* Defines for SPL */
-#define CONFIG_SPL_OMAP3_ID_NAND
-
/* NAND: SPL falcon mode configs */
#ifdef CONFIG_SPL_OS_BOOT
-#define CONFIG_CMD_SPL_NAND_OFS 0x240000
#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000
-#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
#endif
#endif /* __CONFIG_H */
projects / u-boot / blobdiff