Mises a jour.

[bacula/docs] / docs / manual-fr / restore.tex

%%
%%

\section*{The Bacula Console Restore Command}
\label{_ChapterStart13}
\index[general]{Command!Bacula Console Restore }
\index[general]{Bacula Console Restore Command }
\addcontentsline{toc}{section}{Bacula Console Restore Command}

\subsection*{General}
\index[general]{General }
\addcontentsline{toc}{subsection}{General}

Below, we will discuss restoring files with the Console {\bf restore} command,
which is the recommended way of doing it. However, there is a standalone
program named {\bf bextract}, which also permits restoring files. For more
information on this program, please see the 
\ilink{Bacula Utility Programs}{bextract} chapter of this manual.
You will also want to look at the {\bf bls} program in the same chapter, which
allows you to list the contents of your Volumes. Finally, if you have an old
Volume that is no longer in the catalog, you can restore the catalog entries
using the program named {\bf bscan}, documented in the same 
\ilink{Bacula Utility Programs}{bextract} chapter. 

In general, to restore a file or a set of files, you must run a {\bf restore}
job. That is a job with {\bf Type = Restore}. As a consequence, you will need
a predefined {\bf restore} job in your {\bf bacula-dir.conf} (Director's
config) file. The exact parameters (Client, FileSet, ...) that you define are
not important as you can either modify them manually before running the job or
if you use the {\bf restore} command, explained below, Bacula will  
automatically set them for you. In fact, you can no longer simply run a restore
job.  You must use the restore command.                                  

Since Bacula is a network backup program, you must be aware that when you
restore files, it is up to you to ensure that you or Bacula have selected the
correct Client and the correct hard disk location for restoring those files.
{\bf Bacula} will quite willingly backup client A, and restore it by sending
the files to a different directory on client B. Normally, you will want to
avoid this, but assuming the operating systems are not too different in their
file structures, this should work perfectly well, if so desired. 
By default, Bacula will restore data to the same Client that was backed
up, and those data will be restored not to the original places but to
{\bf /tmp/bacula-restores}.  You may modify any of these defaults when the
restore command prompts you to run the job by selecting the {\bf mod}
option.

\label{Example1}
\subsection*{The Restore Command}
\index[general]{Command!Restore }
\index[general]{Restore Command }
\addcontentsline{toc}{subsection}{Restore Command}

Since Bacula maintains a catalog of your files and on which Volumes (disk or
tape), they are stored, it can do most of the bookkeeping work, allowing you
simply to specify what kind of restore you want (current, before a particular
date), and what files to restore. Bacula will then do the rest. 

This is accomplished using the {\bf restore} command in the Console. First you
select the kind of restore you want, then the JobIds are selected,
the File records for those Jobs are placed in an internal Bacula directory
tree, and the restore enters a file selection mode that allows you to
interactively walk up and down the file tree selecting individual files to be
restored. This mode is somewhat similar to the standard Unix {\bf restore}
program's interactive file selection mode. 

If your Files have been pruned, the {\bf restore} command will be unable
to find any files to restore. See below for more details on this. 

Within the Console program, after entering the {\bf restore} command, you are
presented with the following selection prompt:  

\footnotesize
\begin{verbatim}
First you select one or more JobIds that contain files
to be restored. You will be presented several methods
of specifying the JobIds. Then you will be allowed to
select which files from those JobIds are to be restored.
To select the JobIds, you have the following choices:
     1: List last 20 Jobs run
     2: List Jobs where a given File is saved
     3: Enter list of comma separated JobIds to select
     4: Enter SQL list command
     5: Select the most recent backup for a client
     6: Select backup for a client before a specified time
     7: Enter a list of files to restore
     8: Enter a list of files to restore before a specified time
     9: Find the JobIds of the most recent backup for a client
    10: Find the JobIds for a backup for a client before a specified time
    11: Enter a list of directories to restore for found JobIds
    12: Cancel
Select item:  (1-12):
\end{verbatim}
\normalsize

\begin{itemize}
\item Item 1 will list the last 20 jobs run. If you find the Job you want,
   you can then select item 3 and enter its JobId(s).

\item Item 2 will list all the Jobs where a specified file is saved.  If you
   find the Job you want, you can then select item 3 and enter the JobId.

\item Item 3 allows you the enter a list of comma separated JobIds whose 
   files will be put into the directory tree. You may then select which
   files from those JobIds to restore.

\item Item 4 allows you to enter any arbitrary SQL command. This is  probably
   the most primitive way of finding the desired JobIds,  but at the same time,
   the most flexible.  Once you have found the JobId(s), you can select item 3
   and enter  them.

\item Item 5 will automatically select the most recent Full backup and all 
   subsequent incremental and differential backups for a specified Client.
   These are the Jobs and Files which, if reloaded, will restore your
   system to the most current saved state.  It automatically enters the
   JobIds found into the directory tree.  This is probably the most
   convenient of all the above options to use if you wish to restore a
   selected Client to its most recent state.

   There are two important things to note. First, this automatic selection
   will never select a job that failed (terminated with an error status).
   If you have such a job and want to recover one or more files from it,
   you will need to explicitly enter the JobId in item 3, then choose the
   files to restore.

   If some of the Jobs that are needed to do the restore have had their 
   File records pruned, the restore will be incomplete. Bacula currently
   does not correctly detect this condition.  You can however, check for
   this by looking carefully at the list of Jobs that Bacula selects and
   prints. If you find Jobs with the JobFiles column set to zero, when
   files should have been backed up, then you should expect problems.

   If all the File records have been pruned, Bacula will realize that there
   are no file records in any of the JobIds chosen and will inform you. It
   will then propose doing a full restore (non-selective) of those JobIds.
   This is possible because Bacula still knows where the beginning of the
   Job data is on the Volumes, even if it does not know where particular
   files are located.

\item Item 6 allows you to specify a date and time, after which Bacula  will
   automatically select the most recent Full backup and all  subsequent
   incremental and differential backups that started  before the specified date
  and time.  

\item Item 7 allows you to specify one or more filenames  (complete path
   required) to be restored. Each filename  is entered one at a time or if you
   prefix a filename  with the less-than symbol (\lt{}) Bacula will read that 
   file and assume it is a list of filenames to be restored.  The filename entry
   mode is terminated by entering a  blank line.

\item Item 8 allows you to specify a date and time before  entering the
   filenames. See Item 7 above for more  details.

\item Item 9 allows you find the JobIds of the most recent backup for
   a client. This is much like option 5 (it uses the same code), but
   those JobIds are retained internally as if you had entered them
   manually.  You may then select item 11 (see below) to restore one
   or more directories.

\item Item 10 is the same as item 9, except that it allows you to enter
   a before date (as with item 6). These JobIds will then be retained
   internally.

\index[general]{Restore Directories}
\item Item 11 allows you to enter a list of JobIds from which you can
   select directories to be restored. The list of JobIds can have been
   previously created by using either item 9 or 10 on the menu.  You
   may then enter a full path to a directory name or a filename preceded
   by a less than sign (\lt{}). The filename should contain a list
   of directories to be restored.  All files in those directories will
   be restored, but if the directory contains subdirectories, nothing
   will be restored in the subdirectory unless you explicitly enter its
   name.

\item Item 12 allows you to cancel the restore command.  
\end{itemize}

As an example, suppose that we select item 5 (restore to most recent state).
It will then ask for the desired Client, which on my system, will print all
the Clients found in the database as follows:  

\footnotesize
\begin{verbatim}
Defined clients:
     1: Rufus
     2: Matou
     3: Polymatou
     4: Minimatou
     5: Minou
     6: MatouVerify
     7: PmatouVerify
     8: RufusVerify
     9: Watchdog
Select Client (File daemon) resource (1-9):
     
\end{verbatim}
\normalsize

You will probably have far fewer Clients than this example, and  if you have
only one Client, it will be automatically selected. In this case, I enter
{\bf Rufus} to select the Client. Then  Bacula needs to know what FileSet is
to be restored, so it  prompts with:  

\footnotesize
\begin{verbatim}
The defined FileSet resources are:
     1: Full Set
     2: Kerns Files
Select FileSet resource (1-2):
     
\end{verbatim}
\normalsize

I choose item 1, which is my full backup. Normally, you will only have a
single FileSet for each Job, and if your machines are similar (all Linux) you
may only have one FileSet for all your Clients. 

At this point, {\bf Bacula} has all the information it needs to find the most
recent set of backups. It will then query the database, which may take a bit
of time, and it will come up with something like the following. Note, some of
the columns are truncated here for presentation: 

\footnotesize
\begin{verbatim}
+-------+------+----------+-------------+-------------+------+-------+----------
--+
| JobId | Levl | JobFiles | StartTime   | VolumeName  | File | SesId |
VolSesTime |
+-------+------+----------+-------------+-------------+------+-------+----------
--+
| 1,792 | F    |  128,374 | 08-03 01:58 | DLT-19Jul02 |   67 |    18 |
1028042998 |
| 1,792 | F    |  128,374 | 08-03 01:58 | DLT-04Aug02 |    0 |    18 |
1028042998 |
| 1,797 | I    |      254 | 08-04 13:53 | DLT-04Aug02 |    5 |    23 |
1028042998 |
| 1,798 | I    |       15 | 08-05 01:05 | DLT-04Aug02 |    6 |    24 |
1028042998 |
+-------+------+----------+-------------+-------------+------+-------+----------
--+
You have selected the following JobId: 1792,1792,1797
Building directory tree for JobId 1792 ...
Building directory tree for JobId 1797 ...
Building directory tree for JobId 1798 ...
cwd is: /
$
\end{verbatim}
\normalsize

Depending on the number of {\bf JobFiles} for each JobId, the {\bf Building
directory tree ..."} can take a bit of time. If you notice ath all the
JobFiles are zero, your Files have probably been pruned and you will not be
able to select any individual files -- it will be restore everything or
nothing.

In our example, Bacula found four Jobs that comprise the most recent backup of
the specified Client and FileSet. Two of the Jobs have the same JobId because
that Job wrote on two different Volumes. The third Job was an incremental
backup to the previous Full backup, and it only saved 254 Files compared to
128,374 for the Full backup. The fourth Job was also an incremental backup
that saved 15 files. 

Next Bacula entered those Jobs into the directory tree, with no files marked
to be restored as a default, tells you how many files are in the tree, and
tells you that the current working directory ({\bf cwd}) is /. Finally, Bacula
prompts with the dollar sign (\$) to indicate that you may enter commands to
move around the directory tree and to select files. 
             
If you want all the files to automatically be marked when the directory
tree is built, enter the command {\bf restore all}.

Instead of choosing item 5 on the first menu (Select the most recent backup
for a client), if we had chosen item 3 (Enter list of JobIds to select) and we
had entered the JobIds {\bf 1792,1797,1798} we would have arrived at the same
point.                 

One point to note, if you are manually entering JobIds, is that you must enter
them in the order they were run (generally in increasing JobId order). If you
enter them out of order and the same file was saved in two or more of the
Jobs, you may end up with an old version of that file (i.e. not the most
recent). 

Directly entering the JobIds can also permit you to recover data from
a Job that wrote files to tape but that terminated with an error status.

While in file selection mode, you can enter {\bf help} or a question mark (?)
to produce a summary of the available commands:  

\footnotesize
\begin{verbatim}
 Command    Description
  =======    ===========
  cd         change current directory
  count      count marked files in and below the cd
  dir        long list current directory, wildcards allowed
  done       leave file selection mode
  estimate   estimate restore size
  exit       same as done command
  find       find files, wildcards allowed
  help       print help
  ls         list current directory, wildcards allowed
  lsmark     list the marked files in and below the cd
  mark       mark dir/file to be restored recursively in dirs
  markdir    mark directory name to be restored (no files)
  pwd        print current working directory
  unmark     unmark dir/file to be restored recursively in dir
  unmarkdir  unmark directory name only no recursion
  quit       quit and do not do restore
  ?          print help
\end{verbatim}
\normalsize

As a default no files have been selected for restore (unless you
added {\bf all} to the command line. If you want to restore
everything, at this point, you should enter {\bf mark *}, and then {\bf done}
and {\bf Bacula} will write the bootstrap records to a file and request your
approval to start a restore job. 

If you do not enter the above mentioned {\bf mark *} command, you will start
with an empty slate. Now you can simply start looking at the tree and {\bf
mark} particular files or directories you want restored. It is easy to make
a mistake in specifying a file to mark or unmark, and Bacula's error handling
is not perfect, so please check your work by using the {\bf ls} or {\bf dir}
commands to see what files are actually selected. Any selected file has its
name preceded by an asterisk. 

To check what is marked or not marked, enter the {\bf count} command, which
displays:  

\footnotesize
\begin{verbatim}
128401 total files. 128401 marked to be restored.
     
\end{verbatim}
\normalsize

Each of the above commands will be described in more detail in the next
section. We continue with the above example, having accepted to restore all
files as Bacula set by default. On entering the {\bf done} command, Bacula
prints:  

\footnotesize
\begin{verbatim}
Bootstrap records written to /home/kern/bacula/working/restore.bsr
The restore job will require the following Volumes:
   
   DLT-19Jul02
   DLT-04Aug02
128401 files selected to restore.
Run Restore job
JobName:    kernsrestore
Bootstrap:  /home/kern/bacula/working/restore.bsr
Where:      /tmp/bacula-restores
Replace:    always
FileSet:    Kerns Files
Client:     Rufus
Storage:    SDT-10000
JobId:      *None*
OK to run? (yes/mod/no):
    
\end{verbatim}
\normalsize

Please examine each of the items very carefully to make sure that they are
correct.  In particular, look at {\bf Where}, which tells you where in the
directory structure the files will be restored, and {\bf Client}, which
tells you which client will receive the files.  Note that by default the
Client which will receive the files is the Client that was backed up.
These items will not always be completed with the correct values depending
on which of the restore options you chose.  You can change any of these
default items by entering {\bf mod} and responding to the prompts.

The above assumes that you have defined a {\bf Restore} Job resource in your
Director's configuration file. Normally, you will only need one Restore Job
resource definition because by its nature, restoring is a manual operation,
and using the Console interface, you will be able to modify the Restore Job to
do what you want. 

An example Restore Job resource definition is given below. 

Returning to the above example, you should verify that the Client name is
correct before running the Job. However, you may want to modify some of the
parameters of the restore job. For example, in addition to checking the Client
it is wise to check that the Storage device chosen by Bacula is indeed
correct. Although the {\bf FileSet} is shown, it will be ignored in restore.
The restore will choose the files to be restored either by reading the {\bf
Bootstrap} file, or if not specified, it will restore all files associated
with the specified backup {\bf JobId} (i.e. the JobId of the Job that
originally backed up the files). 

Finally before running the job, please note that the default location for
restoring files is {\bf not} their original locations, but rather the directory
{\bf /tmp/bacula-restores}. You can change this default by modifying your {\bf
bacula-dir.conf} file, or you can modify it using the {\bf mod} option. If you
want to restore the files to their original location, you must have {\bf
Where} set to nothing or to the root, i.e. {\bf /}. 

If you now enter {\bf yes}, Bacula will run the restore Job. The Storage
daemon will first request Volume {\bf DLT-19Jul02} and after the appropriate
files have been restored from that volume, it will request Volume {\bf
DLT-04Aug02}. 

\subsection*{Selecting Files by Filename}
\index[general]{Selecting Files by Filename }
\index[general]{Filename!Selecting Files by }
\addcontentsline{toc}{subsection}{Selecting Files by Filename}

If you have a small number of files to restore, and you know the filenames,
you can either put the list of filenames in a file to be read by Bacula, or
you can enter the names one at a time. The filenames must include the full
path and filename. No wild cards are used. 

To enter the files, after the {\bf restore}, you select item number 7 from the
prompt list: 

\footnotesize
\begin{verbatim}
To select the JobIds, you have the following choices:
     1: List last 20 Jobs run
     2: List Jobs where a given File is saved
     3: Enter list of comma separated JobIds to select
     4: Enter SQL list command
     5: Select the most recent backup for a client
     6: Select backup for a client before a specified time
     7: Enter a list of files to restore
     8: Enter a list of files to restore before a specified time
     9: Find the JobIds of the most recent backup for a client
    10: Find the JobIds for a backup for a client before a specified time
    11: Enter a list of directories to restore for found JobIds
    12: Cancel
Select item:  (1-12):
\end{verbatim}
\normalsize

which then prompts you for the client name: 

\footnotesize
\begin{verbatim}
Defined Clients:
     1: Timmy
     2: Tibs
     3: Rufus
Select the Client (1-3): 3
\end{verbatim}
\normalsize

Of course, your client list will be different, and if you have only one
client, it will be automatically selected. And finally, Bacula requests you to
enter a filename: 

\footnotesize
\begin{verbatim}
Enter filename:
\end{verbatim}
\normalsize

At this point, you can enter the full path and filename 

\footnotesize
\begin{verbatim}
Enter filename: /home/kern/bacula/k/Makefile.in
Enter filename:
\end{verbatim}
\normalsize

as you can see, it took the filename. If Bacula cannot find a copy of the
file, it prints the following: 

\footnotesize
\begin{verbatim}
Enter filename: junk filename
No database record found for: junk filename
Enter filename:
\end{verbatim}
\normalsize

If you want Bacula to read the filenames from a file, you simply precede the
filename with a less-than symbol (\lt{}). When you have entered all the
filenames, you enter a blank line, and Bacula will write the bootstrap file,
tells you what tapes will be used, and proposes a Restore job to be run: 

\footnotesize
\begin{verbatim}
Enter filename:
Automatically selected Storage: DDS-4
Bootstrap records written to /home/kern/bacula/working/restore.bsr
The restore job will require the following Volumes:
   
   test1
1 file selected to restore.
Run Restore job
JobName:    kernsrestore
Bootstrap:  /home/kern/bacula/working/restore.bsr
Where:      /tmp/bacula-restores
Replace:    always
FileSet:    Kerns Files
Client:     Rufus
Storage:    DDS-4
When:       2003-09-11 10:20:53
Priority:   10
OK to run? (yes/mod/no):
\end{verbatim}
\normalsize

It is possible to automate the selection by file by putting your list of files
in say {\bf /tmp/file-list}, then using the following command: 

\footnotesize
\begin{verbatim}
restore client=Rufus file=</tmp/file-list
\end{verbatim}
\normalsize

If in modifying the parameters for the Run Restore job, you find that Bacula
asks you to enter a Job number, this is because you have not yet specified
either a Job number or a Bootstrap file. Simply entering zero will allow you
to continue and to select another option to be modified. 
\label{CommandArguments}

\subsection*{Command Line Arguments}
\index[general]{Arguments!Command Line }
\index[general]{Command Line Arguments }
\addcontentsline{toc}{subsection}{Command Line Arguments}

If all the above sounds complicated, you will probably agree that it really
isn't after trying it a few times. It is possible to do everything that was
shown above, with the exception of selecting the FileSet, by using command
line arguments with a single command by entering: 

\footnotesize
\begin{verbatim}
restore client=Rufus select current all done yes
\end{verbatim}
\normalsize

The {\bf client=Rufus} specification will automatically select Rufus as the
client, the {\bf current} tells Bacula that you want to restore the system to
the most current state possible, and the {\bf yes} suppresses the final {\bf
yes/mod/no} prompt and simply runs the restore. 

The full list of possible command line arguments are: 

\begin{itemize}
\item {\bf all} -- select all Files to be restored.  
\item {\bf select} -- use the tree selection method.  
\item {\bf done} -- do not prompt the user in tree mode.  
\item {\bf current} -- automatically select the most current set of  backups
   for the specified client.  
\item {\bf client=xxxx} -- select the specified client.  
\item {\bf jobid=nnn} -- specify a JobId or comma separated list of  JobIds to
   be restored.  
\item {\bf before=YYYY-MM-DD HH:MM:SS} -- specify a date and time to  which
   the system should be restored. Only Jobs started before  the specified
   date/time will be selected, and as is the case  for {\bf current} Bacula will
automatically find the most  recent prior Full save and all Differential and
Incremental  saves run before the date you specify. Note, this command is  not
too user friendly in that you must specify the date/time  exactly as shown. 
\item {\bf file=filename} -- specify a filename to be restored. You  must
   specify the full path and filename. Prefixing the entry  with a less-than
sign
   (\lt{}) will cause Bacula to assume that the  filename is on your system and
contains a list of files to be  restored. Bacula will thus read the list from
that file. Multiple  file=xxx specifications may be specified on the command
line. 
\item {\bf jobid=nnn} -- specify a JobId to be restored. 
\item {\bf pool=pool-name} -- specify a Pool name to be used for selection  of
   Volumes when specifying options 5 and 6 (restore current system,  and restore
   current system before given date). This permits you to  have several Pools,
possibly one offsite, and to select the Pool to  be used for restoring.  
\item {\bf yes} -- automatically run the restore without prompting  for
   modifications (most useful in batch scripts). 
   \end{itemize}

\subsection*{Restoring Directory Attributes}
\index[general]{Attributes!Restoring Directory }
\index[general]{Restoring Directory Attributes }
\addcontentsline{toc}{subsection}{Restoring Directory Attributes}

Depending how you do the restore, you may or may not get the directory entries
back to their original state. Here are a few of the problems you can
encounter, and for same machine restores, how to avoid them. 

\begin{itemize}
\item You backed up on one machine and are restoring to another that is 
   either a different OS or doesn't have the same users/groups defined.  Bacula
   does the best it can in these situations.  
\item You are restoring into a directory that is already created and has  file
   creation restrictions. Bacula tries to reset everything  but without walking
   up the full chain of directories and modifying  them all during the restore,
   which Bacula does and will not do,  getting permissions back correctly in
this
   situation depends to a  large extent on your OS.  
\item You selected one or more files in a directory, but did not select  the
   directory entry to be restored. In that case, if the directory  is not on
disk
   Bacula simply creates the directory with some default  attributes which may
   not be the same as the original.  If you do not select a directory and all
its
   contents to be restored,  you can still select items within the directory to
   be restored by  individually marking those files, but in that case, you
should
   individually use the "markdir" command to select all higher level 
   directory entries (one at a time) to be restored if you want the  directory
   entries properly restored. 
\end{itemize}

\label{Windows}

\subsection*{Restoring on Windows}
\index[general]{Restoring on Windows }
\index[general]{Windows!Restoring on }
\addcontentsline{toc}{subsection}{Restoring on Windows}

If you are restoring on WinNT/2K/XP systems, Bacula will restore the files
with the original ownerships and permissions as would be expected.  This is
also true if you are restoring those files to an alternate directory (using
the Where option in restore).  However, if the alternate directory does not
already exist, the Bacula File daemon (Client) will try to create it.  In
some cases, it may not create the directories, and if it does since the
File daemon runs under the SYSTEM account, the directory will be created
with SYSTEM ownership and permissions.  In this case, you may have problems
accessing the newly restored files.

To avoid this problem, you should create any alternate directory before doing
the
restore. Bacula will not change the ownership and permissions of the directory
if it is already created as long as it is not one of the directories being
restored (i.e. written to tape). 

The default restore location is {\bf /tmp/bacula-restores/} and if you are
restoring from drive {\bf E:}, the default will be 
{\bf /tmp/bacula-restores/e/}, so you should ensure that this directory
exists before doing the restore, or use the {\bf mod} option to
select a different {\bf where} directory that does exist.

Some users have experienced problems restoring files that participate in
the Active Directory. They also report that changing the userid under which
Bacula (bacula-fd.exe) runs, from SYSTEM to a Domain Admin userid, resolves
the problem.


\subsection*{Restoring Files Can Be Slow}
\index[general]{Slow!Restoring Files Can Be }
\index[general]{Restoring Files Can Be Slow }
\addcontentsline{toc}{subsection}{Restoring Files Can Be Slow}

Restoring files is generally {\bf much} slower than backing them up for several
reasons. The first is that during a backup the tape is normally already
positioned and Bacula only needs to write. On the other hand, because restoring
files is done so rarely, Bacula keeps only the start file and block on the
tape for the whole job rather than on a file by file basis which would use
quite a lot of space in the catalog. 

Bacula will forward space to the correct file mark on the tape for the Job,
then forward space to the correct block, and finally sequentially read each
record until it gets to the correct one(s) for the file or files you want to
restore. Once the desired files are restored, Bacula will stop reading the
tape. 

Finally, instead of just reading a file for backup, during the restore, Bacula
must create the file, and the operating system must allocate disk space for
the file as Bacula is restoring it. 

For all the above reasons the restore process is generally much slower than
backing up (sometimes it takes three times as long).

\subsection*{Problems Restoring Files}
\index[general]{Files!Problems Restoring }
\index[general]{Problems Restoring Files }
\addcontentsline{toc}{subsection}{Problems Restoring Files}

The most frequent problems users have restoring files are error messages such
as: 

\footnotesize
\begin{verbatim}
04-Jan 00:33 z217-sd: RestoreFiles.2005-01-04_00.31.04 Error:
block.c:868 Volume data error at 20:0! Short block of 512 bytes on
device /dev/tape discarded.
\end{verbatim}
\normalsize

or 

\footnotesize
\begin{verbatim}
04-Jan 00:33 z217-sd: RestoreFiles.2005-01-04_00.31.04 Error:
block.c:264 Volume data error at 20:0! Wanted ID: "BB02", got ".".
Buffer discarded.
\end{verbatim}
\normalsize

Both these kinds of messages indicate that you were probably running your tape
drive in fixed block mode rather than variable block mode. Fixed block mode
will work with any program that reads tapes sequentially such as tar, but
Bacula repositions the tape on a block basis when restoring files because this
will speed up the restore by orders of magnitude when only a few files are being
restored. There are several ways that you can attempt to recover from this
unfortunate situation. 

Try the following things, each separately, and reset your Device resource to
what it is now after each individual test: 

\begin{enumerate}
\item Set "Block Positioning = no" in your Device resource  and try the
   restore. This is a new directive and untested. 
\item Set "Minimum Block Size = 512" and "Maximum  Block Size = 512" and
   try the restore. Again send me the  full job report output. If you are able
   to
   determine the  block size your drive was previously using, you should try 
   that size if 512 does not work. 
\item Try editing the restore.bsr file at the Run xxx yes/mod/no prompt 
   before starting the restore job and remove all the VolBlock  statements.
   These
   are what causes Bacula to reposition the tape,  and where problems occur if
   you have a fixed block size set  for your drive. The VolFile commands also
   cause repositioning,  but this will work regardless of the block size. 
\item Use bextract to extract the files you want -- it reads the  Volume
   sequentially if you use the include list feature, or  if you use a .bsr file,
   but remove all the VolBlock statements  after the .bsr file is created (at
   the
   Run yes/mod/no) prompt but  before you start the restore. 
\end{enumerate}

\subsection*{Example Restore Job Resource}
\index[general]{Example Restore Job Resource }
\index[general]{Resource!Example Restore Job }
\addcontentsline{toc}{subsection}{Example Restore Job Resource}

\footnotesize
\begin{verbatim}
Job {
  Name = "RestoreFiles"
  Type = Restore
  Client = Any-client
  FileSet = "Any-FileSet"
  Storage = Any-storage
  Where = /tmp/bacula-restores
  Messages = Standard
  Pool = Default
}
\end{verbatim}
\normalsize

If {\bf Where} is not specified, the default location for restoring files will
be their original locations. 
\label{Selection}

\subsection*{File Selection Commands}
\index[general]{Commands!File Selection }
\index[general]{File Selection Commands }
\addcontentsline{toc}{subsection}{File Selection Commands}

After you have selected the Jobs to be restored and Bacula has created the
in-memory directory tree, you will enter file selection mode as indicated by
the dollar sign ({\bf \$}) prompt. While in this mode, you may use the
commands listed above. The basic idea is to move up and down the in memory
directory structure with the {\bf cd} command much as you normally do on the
system. Once you are in a directory, you may select the files that you want
restored. As a default no files are marked to be restored. If you wish to
start with all files, simply enter: {\bf cd /} and {\bf mark *}. Otherwise
proceed to select the files you wish to restore by marking them with the {\bf
mark} command. The available commands are: 

\begin{description}

\item [cd]
   The {\bf cd} command changes the current directory to  the argument
   specified.
   It operates much like the Unix {\bf cd} command.  Wildcard specifications are
   not permitted.  

   Note, on Windows systems, the various drives (c:, d:, ...) are treated  like
   a
   directory within the file tree while in the file  selection mode. As a
   consequence, you must do a {\bf cd c:} or  possibly in some cases a {\bf cd
   C:} (note upper case)  to get down to the first directory.  

\item [dir]
   \index[dir]{dir }
   The {\bf dir} command is similar to the {\bf ls} command,  except that it
   prints it in long format (all details). This command  can be a bit slower
   than
   the {\bf ls} command because it must access  the catalog database for the
   detailed information for each file.  

\item [estimate]
   \index[dir]{estimate }
   The {\bf estimate} command prints a summary of  the total files in the tree,
   how many are marked to be restored, and  an estimate of the number of bytes
   to
   be restored. This can be useful  if you are short on disk space on the
   machine
   where the files will be  restored.  

\item [find]
   \index[dir]{find }
   The {\bf find} command accepts one or more arguments  and displays all files
   in the tree that match that argument. The argument  may have wildcards. It is
   somewhat similar to the Unix command  {\bf find / -name arg}.  

\item [ls]
   The {\bf ls} command produces a listing of all the files  contained in the
   current directory much like the Unix {\bf ls} command.  You may specify an
   argument containing wildcards, in which case only  those files will be
listed.
   Any file that is marked to be restored will  have its name preceded by an
   asterisk ({\bf *}). Directory names  will be terminated with a forward slash
   ({\bf /}) to distinguish them  from filenames.  

\item [lsmark]
   \index[fd]{lsmark }
   The {\bf lsmark} command is the same as the  {\bf ls} except that it will
   print only those files marked for  extraction. The other distinction is that
   it will recursively  descend into any directory selected. 

\item [mark]
   \index[dir]{mark }
   The {\bf mark} command allows you to mark files to be restored. It takes a
   single argument which is the filename  or directory name in the current
   directory to be marked for extraction.  The argument may be a wildcard
   specification, in which  case all files that match in the current directory
   are marked to be  restored. If the argument matches a directory rather than a
   file,  then the directory and all the files contained in that directory
   (recursively)  are marked to be restored. Any marked file will have its name 
   preceded with an asterisk ({\bf *}) in the output produced by the  {\bf ls}
or
   {\bf dir} commands. Note, supplying a full path on  the mark command does not
   work as expected to select a file or  directory in the current directory.
   Also, the {\bf mark} command works  on the current and lower directories but
   does not touch higher level  directories.  

   After executing the {\bf mark} command, it will print a brief summary:  

\footnotesize
\begin{verbatim}
    No files marked.
    
\end{verbatim}
\normalsize

   If no files were marked, or:  

\footnotesize
\begin{verbatim}
    nn files marked.
    
\end{verbatim}
\normalsize

   if some files are marked.  

\item [unmark]
   \index[dir]{unmark }
   The {\bf unmark} is identical to the {\bf mark}  command, except that it
   unmarks the specified file or files so that  they will not be restored. Note:
   the {\bf unmark} command works from  the current directory, so it does not
   unmark any files at a higher  level. First do a {\bf cd /} before the {\bf
   unmark *} command if  you want to unmark everything.  

\item [pwd]
   \index[dir]{pwd }
   The {\bf pwd} command prints the current working  directory. It accepts no
   arguments.  

\item [count]
   \index[dir]{count }
   The {\bf count} command prints the total files in the  directory tree and the
   number of files marked to be restored.  

\item [done]
   \index[dir]{done }
   This command terminates file selection mode.  

\item [exit]
   \index[fd]{exit }
   This command terminates file selection mode (the same as  done).  

\item [quit]
   \index[fd]{quit }
   This command terminates the file selection and does  not run the restore
job. 


\item [help]
   \index[fd]{help }
   This command prints a summary of the commands available.  

\item [?]
   This command is the same as the {\bf help} command.  
\end{description}

\subsection*{Restoring When Things Go Wrong}
\index[general]{Restoring When Things Go Wrong }
\addcontentsline{toc}{subsection}{Restoring When Things Go Wrong}

This and the following sections will try to present a few of the kinds of
problems that can come up making restoring more difficult. I'll try to
provide a few ideas how to get out of these problem situations.

\begin{description}
\item [Problem]
   Your catalog has been damaged and Bacula either doesn't work or prints
   errors.
\item[Solution]
   For SQLite, use the vacuum command to try to fix the database. For either
   MySQL or PostgreSQL, see the vendor's documentation. They have specific tools
   that check and repair databases.

   Assuming the above does not resolve the problem, you will need to restore
   or rebuild your catalog.
\item[Problem]
   How do I restore my catalog?
\item[Solution]
   If you have backed up your database nightly (as you should) and you
   have made a bootstrap file, you can immediately load back your
   database (or the ASCII SQL output).  Make a copy of your current
   database, then re-initialize it, by running the following scripts:
\begin{verbatim}
   ./drop_bacula_tables
   ./make_bacula_tables
\end{verbatim}
   After re-initializing the database, you should be able to run 
   Bacula. If you now try to use the restore command, it will not 
   work because the database will be empty. However, you can manually
   run a restore job and specify your bootstrap file. You do so
   by entering the {bf run} command in the console and selecting the
   restore job.  If you are using the default bacula-dir.conf, this
   Job will be named {\bf RestoreFiles}. Most likely it will prompt
   you with something such as:
\footnotesize
\begin{verbatim}
Run Restore job
JobName:    RestoreFiles
Bootstrap:  /home/kern/bacula/working/restore.bsr
Where:      /tmp/bacula-restores
Replace:    always
FileSet:    Full Set
Client:     rufus-fd
Storage:    File
When:       2005-07-10 17:33:40
Catalog:    MyCatalog
Priority:   10
OK to run? (yes/mod/no): 
\end{verbatim}
\normalsize
   A number of the items will be different in your case. What you want
   to do is: to use the mod option to change the Bootstrap to point to 
   your saved bootstrap file; and to make sure all the other items
   such as Client, Storage, Catalog, and Where are correct. The
   FileSet is not used when you specify a bootstrap file.
   Once you have set all the correct values, run the Job and
   it will restore the backup of your database. You will then
   need to follow the instructions for your database type to
   recreate the database from the ASCII backup file.

      
\item[Solution]
   If you did save your database but did not make a bootstrap file, then 
   recovering the database 
   is more difficult. You will probably need to use bextract to extract the
   backup copy.
   First you should locate the listing of the job report from the last catalog
   backup.  It has important information that will allow you to quickly find
   your database file.  For example, in the job report for the CatalogBackup
   shown below, the critical items are the Volume name(s), the Volume Session Id
   and the Volume Session Time.  If you know those, you can easily restore your
   Catalog.
\footnotesize
\begin{verbatim}

22-Apr 10:22 HeadMan: Start Backup JobId 7510,
Job=CatalogBackup.2005-04-22_01.10.0
22-Apr 10:23 HeadMan: Bacula 1.37.14 (21Apr05): 22-Apr-2005 10:23:06
  JobId:                  7510
  Job:                    CatalogBackup.2005-04-22_01.10.00
  Backup Level:           Full
  Client:                 Polymatou
  FileSet:                "CatalogFile" 2003-04-10 01:24:01
  Pool:                   "Default"
  Storage:                "DLTDrive"
  Start time:             22-Apr-2005 10:21:00
  End time:               22-Apr-2005 10:23:06
  FD Files Written:       1
  SD Files Written:       1
  FD Bytes Written:       210,739,395
  SD Bytes Written:       210,739,521
  Rate:                   1672.5 KB/s
  Software Compression:   None
  Volume name(s):         DLT-22Apr05
  Volume Session Id:      11
  Volume Session Time:    1114075126
  Last Volume Bytes:      1,428,240,465
  Non-fatal FD errors:    0
  SD Errors:              0
  FD termination status:  OK
  SD termination status:  OK
  Termination:            Backup OK

\end{verbatim}
\normalsize
  From the above information, you can manually create a bootstrap file,
  and then follow the instructions given above for restoring your database.
  A reconstructed bootstrap file for the above backup Job would look
  like the following:
\footnotesize
\begin{verbatim}
Volume="DLT-22Apr05"
VolSessionId=11
VolSessionTime=1114075126
FileIndex=1-1
\end{verbatim}
\normalsize    
  Where we have inserted the Volume name, Volume Session Id, and Volume Session
Time that
  correspond to the values in the job report.  We've also used a FileIndex of
one,
  which will always be the case providing that there was only one file
  backed up in the job.
  
  The disadvantage of this bootstrap file compared to what is created when you
  ask for one to be written, is that there is no File and Block specified, so
  the restore code must search all data in the Volume to find the requested
  file. A fully specified bootstrap file would have the File and Blocks
specified
  as follows:
\footnotesize
\begin{verbatim}
Volume="DLT-22Apr05"
VolSessionId=11
VolSessionTime=1114075126
VolFile=118-118
VolBlock=0-4053
FileIndex=1-1
\end{verbatim}
\normalsize
\item [Problem]
  You don't have a bootstrap file, and you don't have the Job report for
  the backup of your database, but you did backup the database, and you
  know the Volume to which it was backed up.
  
\item [Solution]
  Use {\bf bls} to indicate where it is on the tape. For example:

\footnotesize
\begin{verbatim}
./bls -j -V DLT-22Apr05 /dev/nst0
\end{verbatim}
\normalsize
  Might produce the following output:
\footnotesize
\begin{verbatim}
bls: butil.c:258 Using device: "/dev/nst0" for reading.
21-Jul 18:34 bls: Ready to read from volume "DLT-22Apr05" on device "DLTDrive"
(/dev/nst0).
Volume Record: File:blk=0:0 SessId=11 SessTime=1114075126 JobId=0 DataLen=164
...
Begin Job Session Record: File:blk=118:0 SessId=11 SessTime=1114075126
JobId=7510
   Job=CatalogBackup.2005-04-22_01.10.0 Date=22-Apr-2005 10:21:00 Level=F Type=B
End Job Session Record: File:blk=118:4053 SessId=11 SessTime=1114075126
JobId=7510
   Date=22-Apr-2005 10:23:06 Level=F Type=B Files=1 Bytes=210,739,395 Errors=0
Status=T
...
21-Jul 18:34 bls: End of Volume at file 201 on device "DLTDrive" (/dev/nst0),
Volume "DLT-22Apr05"
21-Jul 18:34 bls: End of all volumes.
\end{verbatim}
\normalsize
  Of course, there will be many more records printed, but we have indicated
  the essential lines of output. From the information on the Begin Job and End 
  Job Session Records, you can reconstruct a bootstrap file such as the one
  shown above.

\item[Problem]
  How can I find where a file is stored.
\item[Solution]
  Normally, it is not necessary, you just use the {\bf restore} command to
restore the 
  most recently saved version (menu option 5), or a version saved before a given
date (menu
  option 8).  If you know the JobId of the job in which it was saved, you can
use menu 
  option 3 to enter that JobId.

  If you would like to know the JobId where a file was saved, select restore
menu option
  2.

  You can also use the {\bf query} command to find information such as: 
\footnotesize
\begin{verbatim}
*query
Available queries:
     1: List Job totals:
     2: List up to 20 places where a File is saved regardless of the directory:
     3: List where the most recent copies of a file are saved:
     4: List last 20 Full Backups for a Client:
     5: List all backups for a Client after a specified time
     6: List all backups for a Client
     7: List Volume Attributes for a selected Volume:
     8: List Volumes used by selected JobId:
     9: List Volumes to Restore All Files:
    10: List Pool Attributes for a selected Pool:
    11: List total files/bytes by Job:
    12: List total files/bytes by Volume:
    13: List Files for a selected JobId:
    14: List Jobs stored in a selected MediaId:
    15: List Jobs stored for a given Volume name:
Choose a query (1-15):
\end{verbatim}
\normalsize

\end{description}