+ An example: I have a multi-drive jukebox (6 drives, 380+ slots)
+ where tapes occasionally get stuck inside the drive. Bacula will
+ notice that the "mtx-changer" command will fail and then fail
+ any backup jobs trying to use that drive. However, it will still
+ keep on trying to run new jobs using that drive and fail -
+ forever, and thus failing lots and lots of jobs... Since we have
+ many drives Bacula could have just automatically disabled
+ further use of that drive and used one of the other ones
+ instead.
+
+Item 20: An option to operate on all pools with update vol parameters
+ Origin: Dmitriy Pinchukov <absh@bossdev.kiev.ua>
+ Date: 16 August 2006
+ Status: Patch made by Nigel Stepp
+
+ What: When I do update -> Volume parameters -> All Volumes
+ from Pool, then I have to select pools one by one. I'd like
+ console to have an option like "0: All Pools" in the list of
+ defined pools.
+
+ Why: I have many pools and therefore unhappy with manually
+ updating each of them using update -> Volume parameters -> All
+ Volumes from Pool -> pool #.
+
+
+Item 21: Include timestamp of job launch in "stat clients" output
+ Origin: Mark Bergman <mark.bergman@uphs.upenn.edu>
+ Date: Tue Aug 22 17:13:39 EDT 2006
+ Status:
+
+ What: The "stat clients" command doesn't include any detail on when
+ the active backup jobs were launched.
+
+ Why: Including the timestamp would make it much easier to decide whether
+ a job is running properly.
+
+ Notes: It may be helpful to have the output from "stat clients" formatted
+ more like that from "stat dir" (and other commands), in a column
+ format. The per-client information that's currently shown (level,
+ client name, JobId, Volume, pool, device, Files, etc.) is good, but
+ somewhat hard to parse (both programmatically and visually),
+ particularly when there are many active clients.
+
+
+
+Item 22: Implement Storage daemon compression
+ Date: 18 December 2006
+ Origin: Vadim A. Umanski , e-mail umanski@ext.ru
+ Status:
+ What: The ability to compress backup data on the SD receiving data
+ instead of doing that on client sending data.
+ Why: The need is practical. I've got some machines that can send
+ data to the network 4 or 5 times faster than compressing
+ them (I've measured that). They're using fast enough SCSI/FC
+ disk subsystems but rather slow CPUs (ex. UltraSPARC II).
+ And the backup server has got a quite fast CPUs (ex. Dual P4
+ Xeons) and quite a low load. When you have 20, 50 or 100 GB
+ of raw data - running a job 4 to 5 times faster - that
+ really matters. On the other hand, the data can be
+ compressed 50% or better - so losing twice more space for
+ disk backup is not good at all. And the network is all mine
+ (I have a dedicated management/provisioning network) and I
+ can get as high bandwidth as I need - 100Mbps, 1000Mbps...
+ That's why the server-side compression feature is needed!
+ Notes:
+
+Item 23: Improve Bacula's tape and drive usage and cleaning management
+ Date: 8 November 2005, November 11, 2005
+ Origin: Adam Thornton <athornton at sinenomine dot net>,
+ Arno Lehmann <al at its-lehmann dot de>
+ Status:
+
+ What: Make Bacula manage tape life cycle information, tape reuse
+ times and drive cleaning cycles.
+
+ Why: All three parts of this project are important when operating
+ backups.
+ We need to know which tapes need replacement, and we need to
+ make sure the drives are cleaned when necessary. While many
+ tape libraries and even autoloaders can handle all this
+ automatically, support by Bacula can be helpful for smaller
+ (older) libraries and single drives. Limiting the number of
+ times a tape is used might prevent tape errors when using
+ tapes until the drives can't read it any more. Also, checking
+ drive status during operation can prevent some failures (as I
+ [Arno] had to learn the hard way...)
+
+ Notes: First, Bacula could (and even does, to some limited extent)
+ record tape and drive usage. For tapes, the number of mounts,
+ the amount of data, and the time the tape has actually been
+ running could be recorded. Data fields for Read and Write
+ time and Number of mounts already exist in the catalog (I'm
+ not sure if VolBytes is the sum of all bytes ever written to
+ that volume by Bacula). This information can be important
+ when determining which media to replace. The ability to mark
+ Volumes as "used up" after a given number of write cycles
+ should also be implemented so that a tape is never actually
+ worn out. For the tape drives known to Bacula, similar
+ information is interesting to determine the device status and
+ expected life time: Time it's been Reading and Writing, number
+ of tape Loads / Unloads / Errors. This information is not yet
+ recorded as far as I [Arno] know. A new volume status would
+ be necessary for the new state, like "Used up" or "Worn out".
+ Volumes with this state could be used for restores, but not
+ for writing. These volumes should be migrated first (assuming
+ migration is implemented) and, once they are no longer needed,
+ could be moved to a Trash pool.
+
+ The next step would be to implement a drive cleaning setup.
+ Bacula already has knowledge about cleaning tapes. Once it
+ has some information about cleaning cycles (measured in drive
+ run time, number of tapes used, or calender days, for example)
+ it can automatically execute tape cleaning (with an
+ autochanger, obviously) or ask for operator assistance loading
+ a cleaning tape.
+
+ The final step would be to implement TAPEALERT checks not only
+ when changing tapes and only sending the information to the
+ administrator, but rather checking after each tape error,
+ checking on a regular basis (for example after each tape
+ file), and also before unloading and after loading a new tape.
+ Then, depending on the drives TAPEALERT state and the known
+ drive cleaning state Bacula could automatically schedule later
+ cleaning, clean immediately, or inform the operator.
+
+ Implementing this would perhaps require another catalog change
+ and perhaps major changes in SD code and the DIR-SD protocol,
+ so I'd only consider this worth implementing if it would
+ actually be used or even needed by many people.
+
+ Implementation of these projects could happen in three distinct
+ sub-projects: Measuring Tape and Drive usage, retiring
+ volumes, and handling drive cleaning and TAPEALERTs.
+
+Item 24: Multiple threads in file daemon for the same job
+ Date: 27 November 2005
+ Origin: Ove Risberg (Ove.Risberg at octocode dot com)
+ Status:
+
+ What: I want the file daemon to start multiple threads for a backup
+ job so the fastest possible backup can be made.
+
+ The file daemon could parse the FileSet information and start
+ one thread for each File entry located on a separate
+ filesystem.
+
+ A confiuration option in the job section should be used to
+ enable or disable this feature. The confgutration option could
+ specify the maximum number of threads in the file daemon.
+
+ If the theads could spool the data to separate spool files
+ the restore process will not be much slower.