item). When doing this, you should consult the \ilink{Storage Daemon
Configuration}{StoredConfChapter} of this manual.
+\item If you are using a Fibre Channel to connect your tape drive to
+ Bacula, please be sure to disable any caching in the NSR (network
+ storage router, which is a Fibre Channel to SCSI converter).
+
\item Run the btape {\bf test} command:
\footnotesize
\end{verbatim}
\normalsize
-It isn't necessary to run the autochanger part of the test at this time, but
-do not go past this point until the basic test succeeds. If you do have
-an autochanger, please be sure to read the
-\ilink{Autochanger chapter}{AutochangersChapter} of this manual.
+ It isn't necessary to run the autochanger part of the test at this time,
+ but do not go past this point until the basic test succeeds. If you do
+ have an autochanger, please be sure to read the \ilink{Autochanger
+ chapter}{AutochangersChapter} of this manual.
\item Run the btape {\bf fill} command, preferably with two volumes. This
can take a long time. If you have an autochanger and it is configured, Bacula
program can be found in the platform/freebsd directory. The instructions
for its use are at the top of the file.
-\item Run Bacula, and backup a reasonably small directory, say 60 Megabytes.
- Do three successive backups of this directory.
+\item Run Bacula, and backup a reasonably small directory, say 60
+ Megabytes. Do three successive backups of this directory.
-\item Stop Bacula, then restart it. Do another full backup of the same
- directory. Then stop and restart Bacula.
+\item Stop Bacula, then restart it. Do another full backup of the same
+ directory. Then stop and restart Bacula.
\item Do a restore of the directory backed up, by entering the following
restore command, being careful to restore it to an alternate location:
+
\footnotesize
\begin{verbatim}
restore select all done
\end{verbatim}
\normalsize
-Do a {\bf diff} on the restored directory to ensure it is identical to the
-original directory. If you are going to backup multiple different systems
-(Linux, Windows, Mac, Solaris, FreeBSD, ...), be sure you test the restore
-on each system type.
+ Do a {\bf diff} on the restored directory to ensure it is identical to the
+ original directory. If you are going to backup multiple different systems
+ (Linux, Windows, Mac, Solaris, FreeBSD, ...), be sure you test the restore
+ on each system type.
\item If you have an autochanger, you should now go back to the btape program
and run the autochanger test:
\end{verbatim}
\normalsize
-Adjust your autochanger as necessary to ensure that it works correctly. See
-the Autochanger chapter of this manual for a complete discussion of testing
-your autochanger.
+ Adjust your autochanger as necessary to ensure that it works correctly. See
+ the Autochanger chapter of this manual for a complete discussion of testing
+ your autochanger.
\item We strongly recommend that you use a dedicated SCSI
-controller for your tape drives. Scanners are known to induce
-serious problems with the SCSI bus, causing it to reset. If the
-SCSI bus is reset while Bacula has the tape drive open, it will
-most likely be fatal to your tape since the drive will rewind.
-These kinds of problems show up in the system log. For example,
-the following was most likely caused by a scanner:
+ controller for your tape drives. Scanners are known to induce
+ serious problems with the SCSI bus, causing it to reset. If the
+ SCSI bus is reset while Bacula has the tape drive open, it will
+ most likely be fatal to your tape since the drive will rewind.
+ These kinds of problems show up in the system log. For example,
+ the following was most likely caused by a scanner:
\footnotesize
\begin{verbatim}
You can find out what SCSI devices you have by doing:
+\footnotesize
+\begin{verbatim}
+lsscsi
+\end{verbatim}
+\normalsize
+
+Typical output is:
+
+\footnotesize
+\begin{verbatim}
+[0:0:0:0] disk ATA ST3160812AS 3.AD /dev/sda
+[2:0:4:0] tape HP Ultrium 2-SCSI F6CH /dev/st0
+[2:0:5:0] tape HP Ultrium 2-SCSI F6CH /dev/st1
+[2:0:6:0] mediumx OVERLAND LXB 0107 -
+[2:0:9:0] tape HP Ultrium 1-SCSI E50H /dev/st2
+[2:0:10:0] mediumx OVERLAND LXB 0107 -
+\end{verbatim}
+\normalsize
+
+There are two drives in one autochanger: /dev/st0 and /dev/st1
+and a third tape drive at /dev/st2. For using them with Bacula, one
+would normally reference them as /dev/nst0 ... /dev/nst2. Not also,
+there are two different autochangers identified as "mediumx OVERLAND LXB".
+They can be addressed via their /dev/sgN designation, which can be
+obtained by counting from the beginning as 0 to each changer. In the
+above case, the two changers are located on /dev/sg3 and /dev/sg5. The one
+at /dev/sg3, controls drives /dev/nst0 and /dev/nst1; and the one at
+/dev/sg5 controles drive /dev/nst2.
+
+If you do not have the {\bf lsscsi} command, you can obtain the same
+information as follows:
+
\footnotesize
\begin{verbatim}
cat /proc/scsi/scsi
\end{verbatim}
\normalsize
-For example, I get the following:
+For the above example with the three drives and two autochangers,
+I get:
+
+\footnotesize
+\begin{verbatim}
+Attached devices:
+Host: scsi0 Channel: 00 Id: 00 Lun: 00
+ Vendor: ATA Model: ST3160812AS Rev: 3.AD
+ Type: Direct-Access ANSI SCSI revision: 05
+Host: scsi2 Channel: 00 Id: 04 Lun: 00
+ Vendor: HP Model: Ultrium 2-SCSI Rev: F6CH
+ Type: Sequential-Access ANSI SCSI revision: 03
+Host: scsi2 Channel: 00 Id: 05 Lun: 00
+ Vendor: HP Model: Ultrium 2-SCSI Rev: F6CH
+ Type: Sequential-Access ANSI SCSI revision: 03
+Host: scsi2 Channel: 00 Id: 06 Lun: 00
+ Vendor: OVERLAND Model: LXB Rev: 0107
+ Type: Medium Changer ANSI SCSI revision: 02
+Host: scsi2 Channel: 00 Id: 09 Lun: 00
+ Vendor: HP Model: Ultrium 1-SCSI Rev: E50H
+ Type: Sequential-Access ANSI SCSI revision: 03
+Host: scsi2 Channel: 00 Id: 10 Lun: 00
+ Vendor: OVERLAND Model: LXB Rev: 0107
+ Type: Medium Changer ANSI SCSI revision: 02
+\end{verbatim}
+\normalsize
+
+
+As an additional example, I get the following (on a different machine from the
+above example):
\footnotesize
\begin{verbatim}
projects / bacula / docs / blobdiff