\index[general]{Drives!Supported Tape }
\index[general]{Supported Tape Drives }
-Bacula uses standard operating system calls (read, write, ioctl) to
+Bacula uses standard operating system calls (read, write, ioctl) to
interface to tape drives. As a consequence, it relies on having a
correctly written OS tape driver. Bacula is known to work perfectly well
with SCSI tape drivers on FreeBSD, Linux, Solaris, and Windows machines,
-and it may work on other *nix machines, but we have not tested it.
+and it may work on other *nix machines.
+
Recently there are many new drives that use IDE, ATAPI, or
SATA interfaces rather than SCSI. On Linux the OnStream drive, which uses
the OSST driver is one such
example, and it is known to work with Bacula. In addition a number of such
tape drives (i.e. OS drivers) seem to work on Windows systems. However,
-non-SCSI tape drives (other than the OnStream) that use ide-scis, ide-tape,
+non-SCSI tape drives (other than the OnStream) that use ide-scis, ide-tape,
or other non-scsi drivers do not function correctly with Bacula (or any
other demanding tape application) as of today (April 2007). If you
have purchased a non-SCSI tape drive for use with Bacula on Linux, there
is a good chance that it will not work. We are working with the kernel
-developers to rectify this situation, but it will not be resolved in the
+developers to rectify this situation, but it will not be resolved in the
near future.
-Even if your drive is on the list below, please check the
+Generally any modern tape drive (i.e. after 2010) will work out
+of the box with Bacula using the standard Bacula Device specification
+in the bacula-sd.conf file.
+
+Even if your drive is on the list below, please check the
\ilink{Tape Testing Chapter}{btape1} of this manual for
procedures that you can use to verify if your tape drive will work with
Bacula. If your drive is in fixed block mode, it may appear to work with
Bacula until you attempt to do a restore and Bacula wants to position the
tape. You can be sure only by following the procedures suggested above and
-testing.
+testing.
It is very difficult to supply a list of supported tape drives, or drives that
are known to work with Bacula because of limited feedback (so if you use
Bacula on a different drive, please let us know). Based on user feedback, the
following drives are known to work with Bacula. A dash in a column means
-unknown:
-
-\addcontentsline{lot}{table}{Supported Tape Drives}
-\begin{longtable}{|p{2.0in}|l|l|p{2.5in}|l|}
- \hline
-\multicolumn{1}{|c| }{\bf OS } & \multicolumn{1}{c| }{\bf Man. } &
-\multicolumn{1}{c| }{\bf Media } & \multicolumn{1}{c| }{\bf Model } &
-\multicolumn{1}{c| }{\bf Capacity } \\
- \hline {- } & {ADIC } & {DLT } & {Adic Scalar 100 DLT } & {100GB } \\
- \hline {- } & {ADIC } & {DLT } & {Adic Fastor 22 DLT } & {- } \\
- \hline {FreeBSD 5.4-RELEASE-p1 amd64 } & {Certance} & {LTO } & {AdicCertance CL400 LTO Ultrium 2 } & {200GB } \\
- \hline {- } & {- } & {DDS } & {Compaq DDS 2,3,4 } & {- } \\
- \hline {SuSE 8.1 Pro} & {Compaq} & {AIT } & {Compaq AIT 35 LVD } & {35/70GB } \\
- \hline {- } & {HP } & {Travan 4 } & {Colorado T4000S } & {- } \\
- \hline {- } & {HP } & {DLT } & {HP DLT drives } & {- } \\
- \hline {- } & {HP } & {LTO } & {HP LTO Ultrium drives } & {- } \\
- \hline {- } & {IBM} & {??} & {3480, 3480XL, 3490, 3490E, 3580 and 3590 drives} & {- } \\
- \hline {FreeBSD 4.10 RELEASE } & {HP } & {DAT } & {HP StorageWorks DAT72i } & {- } \\
- \hline {- } & {Overland } & {LTO } & {LoaderXpress LTO } & {- } \\
- \hline {- } & {Overland } & {- } & {Neo2000 } & {- } \\
- \hline {- } & {OnStream } & {- } & {OnStream drives (see below) } & {- } \\
- \hline {FreeBSD 4.11-Release} & {Quantum } & {SDLT } & {SDLT320 } & {160/320GB } \\
- \hline {- } & {Quantum } & {DLT } & {DLT-8000 } & {40/80GB } \\
- \hline {Linux } & {Seagate } & {DDS-4 } & {Scorpio 40 } & {20/40GB } \\
- \hline {FreeBSD 4.9 STABLE } & {Seagate } & {DDS-4 } & {STA2401LW } & {20/40GB } \\
- \hline {FreeBSD 5.2.1 pthreads patched RELEASE } & {Seagate } & {AIT-1 } & {STA1701W} & {35/70GB } \\
- \hline {Linux } & {Sony } & {DDS-2,3,4 } & {- } & {4-40GB } \\
- \hline {Linux } & {Tandberg } & {- } & {Tandbert MLR3 } & {- } \\
- \hline {FreeBSD } & {Tandberg } & {- } & {Tandberg SLR6 } & {- } \\
- \hline {Solaris } & {Tandberg } & {- } & {Tandberg SLR75 } & {- } \\
- \hline
-
-\end{longtable}
+unknown:
+
+\LTXtable{0.95\linewidth}{table_tapedrives}
+%\addcontentsline{lot}{table}{Supported Tape Drives}
There is a list of \ilink{supported autochangers}{Models} in the Supported
Autochangers chapter of this document, where you will find other tape drives
-that work with Bacula.
+that work with Bacula.
\section{Unsupported Tape Drives}
\label{UnSupportedDrives}
Previously OnStream IDE-SCSI tape drives did not work with Bacula. As of
Bacula version 1.33 and the osst kernel driver version 0.9.14 or later, they
-now work. Please see the testing chapter as you must set a fixed block size.
+now work. Please see the testing chapter as you must set a fixed block size.
QIC tapes are known to have a number of particularities (fixed block size, and
one EOF rather than two to terminate the tape). As a consequence, you will
need to take a lot of care in configuring them to make them work correctly
-with Bacula.
+with Bacula.
\section{FreeBSD Users Be Aware!!!}
\index[general]{FreeBSD Users Be Aware }
Unless you have patched the pthreads library on FreeBSD 4.11 systems, you will
lose data when Bacula spans tapes. This is because the unpatched pthreads
library fails to return a warning status to Bacula that the end of the tape is
-near. This problem is fixed in FreeBSD systems released after 4.11. Please see the
-\ilink{Tape Testing Chapter}{FreeBSDTapes} of this manual for
-{\bf important} information on how to configure your tape drive for
-compatibility with Bacula.
+near. This problem is fixed in FreeBSD systems released after 4.11. Please see the
+\bsysxrlink{Tape testing}{FreeBSDTapes}{problems}{section} of \problemsman{}
+for {\bf important} information on how to configure your tape drive for
+compatibility with \mbacula{}.
\section{Supported Autochangers}
\index[general]{Autochangers!Supported }
\index[general]{Supported Autochangers }
-For information on supported autochangers, please see the
+For information on supported autochangers, please see the
\ilink{Autochangers Known to Work with Bacula}{Models}
-section of the Supported Autochangers chapter of this manual.
+section of the Supported Autochangers chapter of this manual.
\section{Tape Specifications}
\index[general]{Specifications!Tape}
If you want to know what tape drive to buy that will work with Bacula,
we really cannot tell you. However, we can say that if you are going
to buy a drive, you should try to avoid DDS drives. The technology is
-rather old and DDS tape drives need frequent cleaning. DLT drives are
-generally much better (newer technology) and do not need frequent
+rather old and DDS tape drives need frequent cleaning. DLT drives are
+generally much better (newer technology) and do not need frequent
cleaning.
Below, you will find a table of DLT and LTO tape specifications that will
-give you some idea of the capacity and speed of modern tapes. The
+give you some idea of the capacity and speed of modern tapes. The
capacities that are listed are the native tape capacity without compression.
All modern drives have hardware compression, and manufacturers often list
-compressed capacity using a compression ration of 2:1. The actual compression
+compressed capacity using a compression ration of 2:1. The actual compression
ratio will depend mostly on the data you have to backup, but I find that
-1.5:1 is a much more reasonable number (i.e. multiply the value shown in
+1.5:1 is a much more reasonable number (i.e. multiply the value shown in
the table by 1.5 to get a rough average of what you will probably see).
The transfer rates are rounded to the nearest GB/hr. All values are provided
by various manufacturers.
required to use (but you may) the same name in your Bacula conf resources.
-\begin{tabular}{|c|c|c|c}
-Media Type & Drive Type & Media Capacity & Transfer Rate \\ \hline
-DDS-1 & DAT & 2 GB & ?? GB/hr \\ \hline
-DDS-2 & DAT & 4 GB & ?? GB/hr \\ \hline
-DDS-3 & DAT & 12 GB & 5.4 GB/hr \\ \hline
-Travan 40 & Travan & 20 GB & ?? GB/hr \\ \hline
-DDS-4 & DAT & 20 GB & 11 GB/hr \\ \hline
-VXA-1 & Exabyte & 33 GB & 11 GB/hr \\ \hline
-DAT-72 & DAT & 36 GB & 13 GB/hr \\ \hline
-DLT IV & DLT8000 & 40 GB & 22 GB/hr \\ \hline
-VXA-2 & Exabyte & 80 GB & 22 GB/hr \\ \hline
-Half-high Ultrium 1 & LTO 1 & 100 GB & 27 GB/hr \\ \hline
-Ultrium 1 & LTO 1 & 100 GB & 54 GB/hr \\ \hline
-Super DLT 1 & SDLT 220 & 110 GB & 40 GB/hr \\ \hline
-VXA-3 & Exabyte & 160 GB & 43 GB/hr \\ \hline
-Super DLT I & SDLT 320 & 160 GB & 58 GB/hr \\ \hline
-Ultrium 2 & LTO 2 & 200 GB & 108 GB/hr \\ \hline
-Super DLT II & SDLT 600 & 300 GB & 127 GB/hr \\ \hline
-VXA-4 & Exabyte & 320 GB & 86 GB/hr \\ \hline
-Ultrium 3 & LTO 3 & 400 GB & 216 GB/hr \\ \hline
-\end{tabular}
+\LTXtable{0.95\linewidth}{table_ltodltspec}
projects / bacula / docs / blobdiff