menuconfig PHYLIB
bool "Ethernet PHY (physical media interface) support"
+ depends on NET
help
Enable Ethernet PHY (physical media interface) support.
if PHYLIB
+config PHY_ADDR
+ int "PHY address"
+ default 1 if ARCH_SUNXI
+ default 0
+ help
+ The address of PHY on MII bus. Usually in range of 0 to 31.
+
+config B53_SWITCH
+ bool "Broadcom BCM53xx (RoboSwitch) Ethernet switch PHY support."
+ help
+ Enable support for Broadcom BCM53xx (RoboSwitch) Ethernet switches.
+ This currently supports BCM53125 and similar models.
+
+if B53_SWITCH
+
+config B53_CPU_PORT
+ int "CPU port"
+ default 8
+
+config B53_PHY_PORTS
+ hex "Bitmask of PHY ports"
+
+endif # B53_SWITCH
+
config MV88E61XX_SWITCH
bool "Marvel MV88E61xx Ethernet switch PHY support."
config PHY_MARVELL
bool "Marvell Ethernet PHYs support"
+config PHY_MESON_GXL
+ bool "Amlogic Meson GXL Internal PHY support"
+
config PHY_MICREL
bool "Micrel Ethernet PHYs support"
help
if PHY_MICREL
config PHY_MICREL_KSZ9021
- bool "Micrel KSZ9021 family support"
+ bool
select PHY_GIGE
- help
- Enable support for the Micrel KSZ9021 GbE PHY family. If
- enabled, the extended register read/write for KSZ9021 PHYs
- is supported through the 'mdio' command and any RGMII signal
- delays configured in the device tree will be applied to the
- PHY during initialisation.
-
- Note that the KSZ9021 uses the same part number os the
- KSZ8921BL, so enabling this option disables support for the
- KSZ8721BL.
+ select PHY_MICREL_KSZ90X1
config PHY_MICREL_KSZ9031
- bool "Micrel KSZ9031 family support"
+ bool
+ select PHY_GIGE
+ select PHY_MICREL_KSZ90X1
+
+config PHY_MICREL_KSZ90X1
+ bool "Micrel KSZ90x1 family support"
select PHY_GIGE
help
- Enable support for the Micrel KSZ9031 GbE PHY family. If
- enabled, the extended register read/write for KSZ9021 PHYs
+ Enable support for the Micrel KSZ9021 and KSZ9031 GbE PHYs. If
+ enabled, the extended register read/write for KSZ90x1 PHYs
is supported through the 'mdio' command and any RGMII signal
delays configured in the device tree will be applied to the
- PHY during initialisatioin.
+ PHY during initialization.
+
+ This should not be enabled at the same time with PHY_MICREL_KSZ8XXX
+ as the KSZ9021 and KS8721 share the same ID.
+
+config PHY_MICREL_KSZ8XXX
+ bool "Micrel KSZ8xxx family support"
+ default y if !PHY_MICREL_KSZ90X1
+ help
+ Enable support for the 8000 series GbE PHYs manufactured by Micrel
+ (now a part of Microchip). This includes drivers for the KSZ804,
+ KSZ8031, KSZ8051, KSZ8081, KSZ8895, KSZ886x, and KSZ8721.
+
+ This should not be enabled at the same time with PHY_MICREL_KSZ90X1
+ as the KSZ9021 and KS8721 share the same ID.
endif # PHY_MICREL