qos_init();
 }
 
-#define TMU0_MSTP125   (1 << 25)
-#define SCIFA0_MSTP204 (1 << 4)
-#define SDHI0_MSTP314  (1 << 14)
-#define SDHI2_MSTP312  (1 << 12)
-#define ETHER_MSTP813  (1 << 13)
-
-#define MSTPSR3                0xE6150048
-#define SMSTPCR3       0xE615013C
+#define TMU0_MSTP125   BIT(25)
 
 #define SD2CKCR                0xE6150078
 #define SD2_97500KHZ   0x7
 {
        /* TMU0 */
        mstp_clrbits_le32(MSTPSR1, SMSTPCR1, TMU0_MSTP125);
-       /* SCIFA0 */
-       mstp_clrbits_le32(MSTPSR2, SMSTPCR2, SCIFA0_MSTP204);
-       /* ETHER */
-       mstp_clrbits_le32(MSTPSR8, SMSTPCR8, ETHER_MSTP813);
-       /* SDHI0,2 */
-       mstp_clrbits_le32(MSTPSR3, SMSTPCR3, SDHI0_MSTP314 | SDHI2_MSTP312);
 
        /*
         * SD0 clock is set to 97.5MHz by default.
        return 0;
 }
 
+#define ETHERNET_PHY_RESET     123     /* GPIO 3 31 */
+
 int board_init(void)
 {
        /* adress of boot parameters */
        gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
 
-       /* Init PFC controller */
-       r8a7790_pinmux_init();
-
        cpld_init();
 
-#ifdef CONFIG_SH_ETHER
-       /* ETHER Enable */
-       gpio_request(GPIO_FN_ETH_CRS_DV, NULL);
-       gpio_request(GPIO_FN_ETH_RX_ER, NULL);
-       gpio_request(GPIO_FN_ETH_RXD0, NULL);
-       gpio_request(GPIO_FN_ETH_RXD1, NULL);
-       gpio_request(GPIO_FN_ETH_LINK, NULL);
-       gpio_request(GPIO_FN_ETH_REF_CLK, NULL);
-       gpio_request(GPIO_FN_ETH_MDIO, NULL);
-       gpio_request(GPIO_FN_ETH_TXD1, NULL);
-       gpio_request(GPIO_FN_ETH_TX_EN, NULL);
-       gpio_request(GPIO_FN_ETH_MAGIC, NULL);
-       gpio_request(GPIO_FN_ETH_TXD0, NULL);
-       gpio_request(GPIO_FN_ETH_MDC, NULL);
-       gpio_request(GPIO_FN_IRQ1, NULL);
-
-       gpio_request(GPIO_GP_3_31, NULL); /* PHY_RST */
-       gpio_direction_output(GPIO_GP_3_31, 0);
+       /* Force ethernet PHY out of reset */
+       gpio_request(ETHERNET_PHY_RESET, "phy_reset");
+       gpio_direction_output(ETHERNET_PHY_RESET, 0);
        mdelay(20);
-       gpio_set_value(GPIO_GP_3_31, 1);
-       udelay(1);
-#endif
+       gpio_direction_output(ETHERNET_PHY_RESET, 1);
 
        return 0;
 }
 
-#define CXR24 0xEE7003C0 /* MAC address high register */
-#define CXR25 0xEE7003C8 /* MAC address low register */
-int board_eth_init(bd_t *bis)
+int dram_init(void)
 {
-       int ret = -ENODEV;
-
-#ifdef CONFIG_SH_ETHER
-       u32 val;
-       unsigned char enetaddr[6];
-
-       ret = sh_eth_initialize(bis);
-       if (!eth_env_get_enetaddr("ethaddr", enetaddr))
-               return ret;
+       if (fdtdec_setup_memory_size() != 0)
+               return -EINVAL;
 
-       /* Set Mac address */
-       val = enetaddr[0] << 24 | enetaddr[1] << 16 |
-             enetaddr[2] << 8 | enetaddr[3];
-       writel(val, CXR24);
+       return 0;
+}
 
-       val = enetaddr[4] << 8 | enetaddr[5];
-       writel(val, CXR25);
-#endif
+int dram_init_banksize(void)
+{
+       fdtdec_setup_memory_banksize();
 
-       return ret;
+       return 0;
 }
 
 /* Stout has KSZ8041NL/RNL */
        return 0;
 }
 
-int board_mmc_init(bd_t *bis)
-{
-       int ret = -ENODEV;
-
-#ifdef CONFIG_SH_SDHI
-       gpio_request(GPIO_FN_SD0_DAT0, NULL);
-       gpio_request(GPIO_FN_SD0_DAT1, NULL);
-       gpio_request(GPIO_FN_SD0_DAT2, NULL);
-       gpio_request(GPIO_FN_SD0_DAT3, NULL);
-       gpio_request(GPIO_FN_SD0_CLK, NULL);
-       gpio_request(GPIO_FN_SD0_CMD, NULL);
-       gpio_request(GPIO_FN_SD0_CD, NULL);
-       gpio_request(GPIO_FN_SD2_DAT0, NULL);
-       gpio_request(GPIO_FN_SD2_DAT1, NULL);
-       gpio_request(GPIO_FN_SD2_DAT2, NULL);
-       gpio_request(GPIO_FN_SD2_DAT3, NULL);
-       gpio_request(GPIO_FN_SD2_CLK, NULL);
-       gpio_request(GPIO_FN_SD2_CMD, NULL);
-       gpio_request(GPIO_FN_SD2_CD, NULL);
-
-       /* SDHI0 - needs CPLD mux setup */
-       gpio_request(GPIO_GP_3_30, NULL);
-       gpio_direction_output(GPIO_GP_3_30, 1); /* VLDO3=3.3V */
-       gpio_request(GPIO_GP_5_24, NULL);
-       gpio_direction_output(GPIO_GP_5_24, 1); /* power on */
-
-       ret = sh_sdhi_init(CONFIG_SYS_SH_SDHI0_BASE, 0,
-                          SH_SDHI_QUIRK_16BIT_BUF);
-       if (ret)
-               return ret;
-
-       /* SDHI2 - needs CPLD mux setup */
-       gpio_request(GPIO_GP_3_29, NULL);
-       gpio_direction_output(GPIO_GP_3_29, 1); /* VLDO4=3.3V */
-       gpio_request(GPIO_GP_5_25, NULL);
-       gpio_direction_output(GPIO_GP_5_25, 1); /* power on */
-
-       ret = sh_sdhi_init(CONFIG_SYS_SH_SDHI2_BASE, 2, 0);
-#endif
-       return ret;
-}
-
-
-int dram_init(void)
-{
-       gd->ram_size = CONFIG_SYS_SDRAM_SIZE;
-
-       return 0;
-}
-
 const struct rmobile_sysinfo sysinfo = {
        CONFIG_ARCH_RMOBILE_BOARD_STRING
 };
-
-static const struct sh_serial_platdata serial_platdata = {
-       .base = SCIFA0_BASE,
-       .type = PORT_SCIFA,
-       .clk = CONFIG_MP_CLK_FREQ,
-};
-
-U_BOOT_DEVICE(stout_serials) = {
-       .name = "serial_sh",
-       .platdata = &serial_platdata,
-};
 
--- /dev/null
+/*
+ * board/renesas/stout/stout_spl.c
+ *
+ * Copyright (C) 2018 Marek Vasut <marek.vasut@gmail.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <dm/platform_data/serial_sh.h>
+#include <asm/processor.h>
+#include <asm/mach-types.h>
+#include <asm/io.h>
+#include <linux/errno.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/arch/rmobile.h>
+#include <asm/arch/rcar-mstp.h>
+
+#include <spl.h>
+
+#define TMU0_MSTP125   BIT(25)
+#define SCIFA0_MSTP204 BIT(4)
+#define QSPI_MSTP917   BIT(17)
+
+#define SD2CKCR                0xE615026C
+#define SD_97500KHZ    0x7
+
+#ifdef CONFIG_TPL_BUILD
+struct reg_config {
+       u16     off;
+       u32     val;
+};
+
+static void dbsc_wait(u16 reg)
+{
+       static const u32 dbsc3_0_base = DBSC3_0_BASE;
+       static const u32 dbsc3_1_base = DBSC3_0_BASE + 0x10000;
+
+       while (!(readl(dbsc3_0_base + reg) & BIT(0)))
+               ;
+
+       while (!(readl(dbsc3_1_base + reg) & BIT(0)))
+               ;
+}
+
+static void tpl_init_sys(void)
+{
+       u32 r0 = 0;
+
+       writel(0xa5a5a500, 0xe6020004);
+       writel(0xa5a5a500, 0xe6030004);
+
+       asm volatile(
+               /* ICIALLU - Invalidate I$ to PoU */
+               "mcr    15, 0, %0, cr7, cr5, 0  \n"
+               /* BPIALL - Invalidate branch predictors */
+               "mcr    15, 0, %0, cr7, cr5, 6  \n"
+               /* Set SCTLR[IZ] */
+               "mrc    15, 0, %0, cr1, cr0, 0  \n"
+               "orr    %0, #0x1800             \n"
+               "mcr    15, 0, %0, cr1, cr0, 0  \n"
+               "isb    sy                      \n"
+               :"=r"(r0));
+}
+
+static void tpl_init_pfc(void)
+{
+       static const struct reg_config pfc_with_unlock[] = {
+               { 0x0090, 0x00140300 },
+               { 0x0094, 0x09500000 },
+               { 0x0098, 0xc0000084 },
+               { 0x0020, 0x01a33492 },
+               { 0x0024, 0x10000000 },
+               { 0x0028, 0x08449252 },
+               { 0x002c, 0x2925b322 },
+               { 0x0030, 0x0c311249 },
+               { 0x0034, 0x10124000 },
+               { 0x0038, 0x00001295 },
+               { 0x003c, 0x50890000 },
+               { 0x0040, 0x0eaa56aa },
+               { 0x0044, 0x55550000 },
+               { 0x0048, 0x00000005 },
+               { 0x004c, 0x54800000 },
+               { 0x0050, 0x3736db55 },
+               { 0x0054, 0x29148da3 },
+               { 0x0058, 0x48c446e1 },
+               { 0x005c, 0x2a3a54dc },
+               { 0x0160, 0x00000023 },
+               { 0x0004, 0xfca0ffff },
+               { 0x0008, 0x3fbffbf0 },
+               { 0x000c, 0x3ffdffff },
+               { 0x0010, 0x00ffffff },
+               { 0x0014, 0xfc3ffff3 },
+               { 0x0018, 0xe4fdfff7 },
+       };
+
+       static const struct reg_config pfc_without_unlock[] = {
+               { 0x0104, 0xffffbfff },
+               { 0x0108, 0xb1ffffe1 },
+               { 0x010c, 0xffffffff },
+               { 0x0110, 0xffffffff },
+               { 0x0114, 0xe047beab },
+               { 0x0118, 0x00000203 },
+       };
+
+       static const u32 pfc_base = 0xe6060000;
+
+       unsigned int i;
+
+       for (i = 0; i < ARRAY_SIZE(pfc_with_unlock); i++) {
+               writel(~pfc_with_unlock[i].val, pfc_base);
+               writel(pfc_with_unlock[i].val,
+                      pfc_base | pfc_with_unlock[i].off);
+       }
+
+       for (i = 0; i < ARRAY_SIZE(pfc_without_unlock); i++)
+               writel(pfc_without_unlock[i].val,
+                      pfc_base | pfc_without_unlock[i].off);
+}
+
+static void tpl_init_gpio(void)
+{
+       static const u16 gpio_offs[] = {
+               0x1000, 0x3000, 0x4000, 0x5000
+       };
+
+       static const struct reg_config gpio_set[] = {
+               { 0x4000, 0x00c00000 },
+               { 0x5000, 0x63020000 },
+       };
+
+       static const struct reg_config gpio_clr[] = {
+               { 0x1000, 0x00000000 },
+               { 0x3000, 0x00000000 },
+               { 0x4000, 0x00c00000 },
+               { 0x5000, 0xe3020000 },
+       };
+
+       static const u32 gpio_base = 0xe6050000;
+
+       unsigned int i;
+
+       for (i = 0; i < ARRAY_SIZE(gpio_offs); i++)
+               writel(0, gpio_base | 0x20 | gpio_offs[i]);
+
+       for (i = 0; i < ARRAY_SIZE(gpio_offs); i++)
+               writel(0, gpio_base | 0x00 | gpio_offs[i]);
+
+       for (i = 0; i < ARRAY_SIZE(gpio_set); i++)
+               writel(gpio_set[i].val, gpio_base | 0x08 | gpio_set[i].off);
+
+       for (i = 0; i < ARRAY_SIZE(gpio_clr); i++)
+               writel(gpio_clr[i].val, gpio_base | 0x04 | gpio_clr[i].off);
+}
+
+static void tpl_init_lbsc(void)
+{
+       static const struct reg_config lbsc_config[] = {
+               { 0x00, 0x00000020 },
+               { 0x08, 0x00002020 },
+               { 0x30, 0x02150326 },
+               { 0x38, 0x077f077f },
+       };
+
+       static const u16 lbsc_offs[] = {
+               0x80, 0x84, 0x88, 0x8c, 0xa0, 0xc0, 0xc4, 0xc8, 0x180
+       };
+
+       static const u32 lbsc_base = 0xfec00200;
+
+       unsigned int i;
+
+       for (i = 0; i < ARRAY_SIZE(lbsc_config); i++) {
+               writel(lbsc_config[i].val,
+                      lbsc_base | lbsc_config[i].off);
+               writel(lbsc_config[i].val,
+                      lbsc_base | (lbsc_config[i].off + 4));
+       }
+
+       for (i = 0; i < ARRAY_SIZE(lbsc_offs); i++)
+               writel(0, lbsc_base | lbsc_offs[i]);
+}
+
+static void tpl_init_dbsc(void)
+{
+       static const struct reg_config dbsc_config1[] = {
+               { 0x0280, 0x0000a55a },
+               { 0x0018, 0x21000000 },
+               { 0x0018, 0x11000000 },
+               { 0x0018, 0x10000000 },
+               { 0x0290, 0x00000001 },
+               { 0x02a0, 0x80000000 },
+               { 0x0290, 0x00000004 },
+       };
+
+       static const struct reg_config dbsc_config2[] = {
+               { 0x0290, 0x00000006 },
+               { 0x02a0, 0x0001c000 },
+       };
+
+       static const struct reg_config dbsc_config3r0d0[] = {
+               { 0x0290, 0x0000000f },
+               { 0x02a0, 0x00181885 },
+               { 0x0290, 0x00000070 },
+               { 0x02a0, 0x7c000887 },
+               { 0x0290, 0x00000080 },
+               { 0x02a0, 0x7c000887 },
+               { 0x0290, 0x00000090 },
+               { 0x02a0, 0x7c000887 },
+               { 0x0290, 0x000000a0 },
+               { 0x02a0, 0x7c000887 },
+               { 0x0290, 0x000000b0 },
+               { 0x02a0, 0x7c000880 },
+               { 0x0290, 0x000000c0 },
+               { 0x02a0, 0x7c000880 },
+               { 0x0290, 0x000000d0 },
+               { 0x02a0, 0x7c000880 },
+               { 0x0290, 0x000000e0 },
+               { 0x02a0, 0x7c000880 },
+       };
+
+       static const struct reg_config dbsc_config3r0d1[] = {
+               { 0x0290, 0x0000000f },
+               { 0x02a0, 0x00181885 },
+               { 0x0290, 0x00000070 },
+               { 0x02a0, 0x7c000887 },
+               { 0x0290, 0x00000080 },
+               { 0x02a0, 0x7c000887 },
+               { 0x0290, 0x00000090 },
+               { 0x02a0, 0x7c000887 },
+               { 0x0290, 0x000000a0 },
+               { 0x02a0, 0x7c000887 },
+       };
+
+       static const struct reg_config dbsc_config3r2[] = {
+               { 0x0290, 0x0000000f },
+               { 0x02a0, 0x00181224 },
+       };
+
+       static const struct reg_config dbsc_config4[] = {
+               { 0x0290, 0x00000010 },
+               { 0x02a0, 0xf004649b },
+               { 0x0290, 0x00000061 },
+               { 0x02a0, 0x0000006d },
+               { 0x0290, 0x00000001 },
+               { 0x02a0, 0x00000073 },
+               { 0x0020, 0x00000007 },
+               { 0x0024, 0x0f030a02 },
+               { 0x0030, 0x00000001 },
+               { 0x00b0, 0x00000000 },
+               { 0x0040, 0x0000000b },
+               { 0x0044, 0x00000008 },
+               { 0x0048, 0x00000000 },
+               { 0x0050, 0x0000000b },
+               { 0x0054, 0x000c000b },
+               { 0x0058, 0x00000027 },
+               { 0x005c, 0x0000001c },
+               { 0x0060, 0x00000006 },
+               { 0x0064, 0x00000020 },
+               { 0x0068, 0x00000008 },
+               { 0x006c, 0x0000000c },
+               { 0x0070, 0x00000009 },
+               { 0x0074, 0x00000012 },
+               { 0x0078, 0x000000d0 },
+               { 0x007c, 0x00140005 },
+               { 0x0080, 0x00050004 },
+               { 0x0084, 0x70233005 },
+               { 0x0088, 0x000c0000 },
+               { 0x008c, 0x00000200 },
+               { 0x0090, 0x00000040 },
+               { 0x0100, 0x00000001 },
+               { 0x00c0, 0x00020001 },
+               { 0x00c8, 0x20042004 },
+               { 0x0380, 0x00020002 },
+               { 0x0390, 0x0000001f },
+       };
+
+       static const struct reg_config dbsc_config5[] = {
+               { 0x0244, 0x00000011 },
+               { 0x0290, 0x00000003 },
+               { 0x02a0, 0x0300c4e1 },
+               { 0x0290, 0x00000023 },
+               { 0x02a0, 0x00fcdb60 },
+               { 0x0290, 0x00000011 },
+               { 0x02a0, 0x1000040b },
+               { 0x0290, 0x00000012 },
+               { 0x02a0, 0x9d9cbb66 },
+               { 0x0290, 0x00000013 },
+               { 0x02a0, 0x1a868400 },
+               { 0x0290, 0x00000014 },
+               { 0x02a0, 0x300214d8 },
+               { 0x0290, 0x00000015 },
+               { 0x02a0, 0x00000d70 },
+               { 0x0290, 0x00000016 },
+               { 0x02a0, 0x00000006 },
+               { 0x0290, 0x00000017 },
+               { 0x02a0, 0x00000018 },
+               { 0x0290, 0x0000001a },
+               { 0x02a0, 0x910035c7 },
+               { 0x0290, 0x00000004 },
+       };
+
+       static const struct reg_config dbsc_config6[] = {
+               { 0x0290, 0x00000001 },
+               { 0x02a0, 0x00000181 },
+               { 0x0018, 0x11000000 },
+               { 0x0290, 0x00000004 },
+       };
+
+       static const struct reg_config dbsc_config7[] = {
+               { 0x0290, 0x00000001 },
+               { 0x02a0, 0x0000fe01 },
+               { 0x0304, 0x00000000 },
+               { 0x00f4, 0x01004c20 },
+               { 0x00f8, 0x014000aa },
+               { 0x00e0, 0x00000140 },
+               { 0x00e4, 0x00081860 },
+               { 0x00e8, 0x00010000 },
+               { 0x0290, 0x00000004 },
+       };
+
+       static const struct reg_config dbsc_config8[] = {
+               { 0x0014, 0x00000001 },
+               { 0x0010, 0x00000001 },
+               { 0x0280, 0x00000000 },
+       };
+
+       static const u32 dbsc3_0_base = DBSC3_0_BASE;
+       static const u32 dbsc3_1_base = DBSC3_0_BASE + 0x10000;
+       static const u32 prr_base = 0xff000044;
+       const u16 prr_rev = readl(prr_base) & 0x7fff;
+       unsigned int i;
+
+       for (i = 0; i < ARRAY_SIZE(dbsc_config1); i++) {
+               writel(dbsc_config1[i].val, dbsc3_0_base | dbsc_config1[i].off);
+               writel(dbsc_config1[i].val, dbsc3_1_base | dbsc_config1[i].off);
+       }
+
+       dbsc_wait(0x2a0);
+
+       for (i = 0; i < ARRAY_SIZE(dbsc_config2); i++) {
+               writel(dbsc_config2[i].val, dbsc3_0_base | dbsc_config2[i].off);
+               writel(dbsc_config2[i].val, dbsc3_1_base | dbsc_config2[i].off);
+       }
+
+       if (prr_rev == 0x4500) {
+               for (i = 0; i < ARRAY_SIZE(dbsc_config3r0d0); i++) {
+                       writel(dbsc_config3r0d0[i].val,
+                               dbsc3_0_base | dbsc_config3r0d0[i].off);
+               }
+               for (i = 0; i < ARRAY_SIZE(dbsc_config3r0d1); i++) {
+                       writel(dbsc_config3r0d1[i].val,
+                               dbsc3_1_base | dbsc_config3r0d1[i].off);
+               }
+       } else if (prr_rev != 0x4510) {
+               for (i = 0; i < ARRAY_SIZE(dbsc_config3r2); i++) {
+                       writel(dbsc_config3r2[i].val,
+                               dbsc3_0_base | dbsc_config3r2[i].off);
+                       writel(dbsc_config3r2[i].val,
+                               dbsc3_1_base | dbsc_config3r2[i].off);
+               }
+       }
+
+       for (i = 0; i < ARRAY_SIZE(dbsc_config4); i++) {
+               writel(dbsc_config4[i].val, dbsc3_0_base | dbsc_config4[i].off);
+               writel(dbsc_config4[i].val, dbsc3_1_base | dbsc_config4[i].off);
+       }
+
+       dbsc_wait(0x240);
+
+       for (i = 0; i < ARRAY_SIZE(dbsc_config5); i++) {
+               writel(dbsc_config5[i].val, dbsc3_0_base | dbsc_config5[i].off);
+               writel(dbsc_config5[i].val, dbsc3_1_base | dbsc_config5[i].off);
+       }
+
+       dbsc_wait(0x2a0);
+
+       for (i = 0; i < ARRAY_SIZE(dbsc_config6); i++) {
+               writel(dbsc_config6[i].val, dbsc3_0_base | dbsc_config6[i].off);
+               writel(dbsc_config6[i].val, dbsc3_1_base | dbsc_config6[i].off);
+       }
+
+       dbsc_wait(0x2a0);
+
+       for (i = 0; i < ARRAY_SIZE(dbsc_config7); i++) {
+               writel(dbsc_config7[i].val, dbsc3_0_base | dbsc_config7[i].off);
+               writel(dbsc_config7[i].val, dbsc3_1_base | dbsc_config7[i].off);
+       }
+
+       dbsc_wait(0x2a0);
+
+       for (i = 0; i < ARRAY_SIZE(dbsc_config8); i++) {
+               writel(dbsc_config8[i].val, dbsc3_0_base | dbsc_config8[i].off);
+               writel(dbsc_config8[i].val, dbsc3_1_base | dbsc_config8[i].off);
+       }
+
+}
+
+static void tpl_init_qspi(void)
+{
+       mstp_clrbits_le32(MSTPSR9, SMSTPCR9, QSPI_MSTP917);
+
+       static const u32 qspi_base = 0xe6b10000;
+
+       writeb(0x08, qspi_base + 0x00);
+       writeb(0x00, qspi_base + 0x01);
+       writeb(0x06, qspi_base + 0x02);
+       writeb(0x01, qspi_base + 0x0a);
+       writeb(0x00, qspi_base + 0x0b);
+       writeb(0x00, qspi_base + 0x0c);
+       writeb(0x00, qspi_base + 0x0d);
+       writeb(0x00, qspi_base + 0x0e);
+
+       writew(0xe080, qspi_base + 0x10);
+
+       writeb(0xc0, qspi_base + 0x18);
+       writeb(0x00, qspi_base + 0x18);
+       writeb(0x00, qspi_base + 0x08);
+       writeb(0x48, qspi_base + 0x00);
+}
+
+void board_init_f(ulong dummy)
+{
+       mstp_clrbits_le32(MSTPSR1, SMSTPCR1, TMU0_MSTP125);
+       mstp_clrbits_le32(MSTPSR2, SMSTPCR2, SCIFA0_MSTP204);
+
+       /*
+        * SD0 clock is set to 97.5MHz by default.
+        * Set SD2 to the 97.5MHz as well.
+        */
+       writel(SD_97500KHZ, SD2CKCR);
+
+       tpl_init_sys();
+       tpl_init_pfc();
+       tpl_init_gpio();
+       tpl_init_lbsc();
+       tpl_init_dbsc();
+       tpl_init_qspi();
+}
+#endif
+
+void spl_board_init(void)
+{
+       /* UART clocks enabled and gd valid - init serial console */
+       preloader_console_init();
+}
+
+void board_boot_order(u32 *spl_boot_list)
+{
+#ifdef CONFIG_TPL_BUILD
+       const u32 jtag_magic = 0x1337c0de;
+       const u32 load_magic = 0xb33fc0de;
+
+       /*
+        * If JTAG probe sets special word at 0xe6300020, then it must
+        * put U-Boot into RAM and TPL will start it from RAM.
+        */
+       if (readl(CONFIG_TPL_TEXT_BASE + 0x20) == jtag_magic) {
+               printf("JTAG boot detected!\n");
+
+               while (readl(CONFIG_TPL_TEXT_BASE + 0x24) != load_magic)
+                       ;
+
+               spl_boot_list[0] = BOOT_DEVICE_RAM;
+               spl_boot_list[1] = BOOT_DEVICE_NONE;
+
+               return;
+       }
+#endif
+
+       /* Boot from SPI NOR with YMODEM UART fallback. */
+       spl_boot_list[0] = BOOT_DEVICE_SPI;
+       spl_boot_list[1] = BOOT_DEVICE_UART;
+       spl_boot_list[2] = BOOT_DEVICE_NONE;
+}
+
+void reset_cpu(ulong addr)
+{
+}