Wolfgang Denk [Fri, 21 Jul 2006 09:16:34 +0000 (11:16 +0200)]
* Cleanup TQM5200 board configurations:
- make highboot configurations use environment at high end, too,
to avoid flash fragmentation
- always use redundand environment
- don't enable video code for modules without graphics controller
- provide useful (though different) mtdparts settings
- get rid of CONFIG_CS_AUTOCONF which was always set anyway
* Extend mkconfig tool to print more useful target name
Wolfgang Denk [Wed, 19 Jul 2006 16:01:38 +0000 (18:01 +0200)]
Add support for high-boot on TQM5200 and TQM5200S boards.
Hint: the CPLD on the TQM5200 must be programmed with a software
version supporting the high boot option! The new TQM5200S is
already supporting this option. On the TQM5200 this option will be
supported in configurations with MPC5200 rev B processors.
To actually "high boot", set jumper X30 on the STK52xx.
Wolfgang Denk [Wed, 19 Jul 2006 15:52:30 +0000 (17:52 +0200)]
Add support for new TQM5200 revisions
- Support for TQM5200S (short version without graphic controller)
- Support for modules with 'N' type S29GL128N Spansion flashes
(requires changes to flash layout)
- Support for MPC5200B cpu (mostly support for second SDRAM bank)
Wolfgang Denk [Wed, 19 Jul 2006 12:49:35 +0000 (14:49 +0200)]
Fix support for PS/2 keyboard on TQM85xx boards
The PS/2 keyobard driver for the TQM85xx modules only supports the
internal DUART of the MPC85xx CPU. Since the MPC8560 doesn't
include a DUART, the TQM8560 modules can't be used with the PS/2
keyboard controller on the STK85xx board.
The PS/2 keyboard driver should work with the modules TQM8540,
TQM8541 and TQM8555, but it only has been tested on a TQM8540, yet.
Make sure the PS/2 controller on the STK85xx is programmed. Jumper
settings: X66 1-2, 9-10; X61 2-3
Wolfgang Denk [Wed, 19 Jul 2006 12:40:43 +0000 (14:40 +0200)]
Adjust filenames for USB update images on TRAB board.
During an automatic update via USB stick, U-Boot searches for
images with the name "firmware.img" and "kernel.img". This names
are now changed to "firmw_01.img" and "kernl_01.img". This is done,
to prevent updates of new boards (with the new macronics "c" step
flashes) with old, incompatible firmware or kernel versions.
Patch by Martin Krause, 21 Jun 2006
Wolfgang Denk [Wed, 19 Jul 2006 12:23:12 +0000 (14:23 +0200)]
Bugfix in VFD routine on TRAB board.
Make sure upper lext pixel can be set to blue, too
(so far only red was possible).
Patch by Martin Krause, 15 Feb 2006
Wolfgang Denk [Wed, 19 Jul 2006 12:13:02 +0000 (14:13 +0200)]
Fix some bugs in TRAB board flash driver.
- increase CFG_FLASH_ERASE_TOUT from 2 to 15 seconds
- use CFG_FLASH_WRITE_TOUT for programming instead of CFG_FLASH_ERASE_TOUT
- remove "Unlock Bypass" mode, because macronix flashes do not support
this mode officially
- fix flash reset command from 0x00FF to 0x00F0. 0x00FF is only specified
for Intel compatible flashes, not for AMD compatible.
Patch by Martin Krause, 15 Feb 2006
Wolfgang Denk [Wed, 19 Jul 2006 11:50:38 +0000 (13:50 +0200)]
Add support for TB5200 board
The TB5200 ("Tinybox") is a small baseboard for the TQM5200 module
integrated in a little aluminium case.
Patch by Martin Krause, 8 Jun 2006
Bugfix in FEC initialisation:
All MII configuration is done via FEC1 registers. But MII_SPEED was
configured according to FEC used. So if only FEC2 was used, this caused
the real MII_SPEED register in FEC1 to stay uninitalised, what lead
to "mii_send STUCK!" messages. Fix: always configure MII_SPEED on FEC1
only.
Wolfgang Denk [Mon, 10 Jul 2006 21:07:28 +0000 (23:07 +0200)]
Major PCMCIA Cleanup to make code better readable and maintainable.
Notes:
- Board-dependend code for RPXLITE and RPXCLASSIC-based boards
placed to the drivers/rpx_pmcia.c file to avoid duplication.
Same for TQM8xx-based boards (drivers/tqm8xx_pmcia.c).
- drivers/i82365.c has been split into two parts located at
board/atc/ti113x.c and board/cpc45/pd67290.c (ATC and CPC45 are
the only boards using CONFIG_82365).
- Changes were tested for clean build and *very* *few* boards.
Wolfgang Denk [Fri, 16 Jun 2006 15:04:45 +0000 (17:04 +0200)]
Add support for CONFIG_SERIAL_MULTI on MPC5xxx
Patch by Martin Krause, 8 Jun 2006
This patch supports two serial consoles on boards with
a MPC5xxx CPU. The console can be switched at runtime
by setting stdin, stdout and stderr to the desired serial
interface (serial0 or serial1). The PSCs to be used as
console port are definded by CONFIG_PSC_CONSOLE
and CONFIG_PSC_CONSOLE2.
See README.serial_multi for details.
Wolfgang Denk [Fri, 16 Jun 2006 14:57:18 +0000 (16:57 +0200)]
Bugfix in I2C initialisation on S3C2400.
If the bus is blocked because of a previously interrupted
transfer, up to eleven clocks are generated on the I2CSCL
line to complete the transfer and to free the bus.
With this fix pin I2CSCL (PG6) is really configured as GPIO
so the clock pulses are really generated.
Patch by Martin Krause, 04 Apr 2006
Wolfgang Denk [Fri, 16 Jun 2006 14:14:28 +0000 (16:14 +0200)]
Fix TRAB channel switching delay for trab_fkt.bin standalone applikation
Patch by Martin Krause, 08 Nov 2005
In tsc2000_read_channel() the delay after setting the multiplexer
to a temperature channel is increased from 1,5 ms to 10 ms. This
is to allow the multiplexer inputs to stabilize after huge steps
of the input signal level.
Wolfgang Denk [Fri, 16 Jun 2006 14:11:34 +0000 (16:11 +0200)]
Adjust TQM5200 make targets
Make the automatic CS configuration the default.
The dedicated configurations CONFIG_TQM5200_AA, CONFIG_TQM5200_AB
and CONFIG_TQM5200_AC are removed.
"TQM5200_config" is now the default for STK52XX.200 base boards.
On a STK52XX.100 base board "TQM5200_STK100_config" must be used.
Patch by Martin Krause, 07 Nov 2005
Wolfgang Denk [Fri, 16 Jun 2006 13:56:12 +0000 (15:56 +0200)]
Fix setting of environment variable "ver" on trab board
The environment variable "ver" is now set before
do_auto_update() is called, so that "ver" can be used
in USB update scripts.
Patch by Martin Krause, 27 Oct 2005
Scott McNutt [Thu, 8 Jun 2006 16:08:12 +0000 (12:08 -0400)]
Nios II - Add EPCS Controller bootrom work-around
-When booting from an epcs controller, the epcs bootrom may leave the
slave select in an asserted state causing soft reset hang. This
patch ensures slave select is negated at reset.
Patch by Scott McNutt, 08 Jun 2006
Scott McNutt [Thu, 8 Jun 2006 15:59:57 +0000 (11:59 -0400)]
Nios II - Fix I/O Macros and mini-app stubs
-Fix asm/io.h macros
-Eliminate use of CACHE_BYPASS in cpu code
-Eliminate assembler warnings
-Fix mini-app stubs and force no small data
Patch by Scott McNutt, 08 Jun 2006
Wolfgang Denk [Tue, 30 May 2006 21:32:44 +0000 (23:32 +0200)]
Fix PCI to memory window size problems on PM82x boards
We use the "automatic" mode that was used for the MPC8266ADS and
MPC8272 boards. Eventually this should be used on all boards?]
Patch by Wolfgang Grandegger, 17 Jan 2006
Wolfgang Denk [Tue, 30 May 2006 13:56:48 +0000 (15:56 +0200)]
* Update Intel IXP4xx support
- Add IXP4xx NPE ethernet MAC support
- Add support for Intel IXDPG425 board
- Add support for Prodrive PDNB3 board
- Add IRQ support
Patch by Stefan Roese, 23 May 2006
[This patch does not include cpu/ixp/npe/IxNpeMicrocode.c which still
sufferes from licensing issues. Blame Intel.]