Stefan Roese [Fri, 28 Jul 2006 16:34:58 +0000 (18:34 +0200)]
PPC440 DDR setup: Set SDRAM0_CFG0[PMU]=0 for best performance
AMCC suggested to set the PMU bit to 0 for best performace on
the PPC440 DDR controller.
Please see doc/README.440-DDR-performance for details.
Patch by Stefan Roese, 28 Jul 2006
Wolfgang Denk [Fri, 21 Jul 2006 09:16:34 +0000 (11:16 +0200)]
* Cleanup TQM5200 board configurations:
- make highboot configurations use environment at high end, too,
to avoid flash fragmentation
- always use redundand environment
- don't enable video code for modules without graphics controller
- provide useful (though different) mtdparts settings
- get rid of CONFIG_CS_AUTOCONF which was always set anyway
* Extend mkconfig tool to print more useful target name
Wolfgang Denk [Wed, 19 Jul 2006 16:01:38 +0000 (18:01 +0200)]
Add support for high-boot on TQM5200 and TQM5200S boards.
Hint: the CPLD on the TQM5200 must be programmed with a software
version supporting the high boot option! The new TQM5200S is
already supporting this option. On the TQM5200 this option will be
supported in configurations with MPC5200 rev B processors.
To actually "high boot", set jumper X30 on the STK52xx.
Wolfgang Denk [Wed, 19 Jul 2006 15:52:30 +0000 (17:52 +0200)]
Add support for new TQM5200 revisions
- Support for TQM5200S (short version without graphic controller)
- Support for modules with 'N' type S29GL128N Spansion flashes
(requires changes to flash layout)
- Support for MPC5200B cpu (mostly support for second SDRAM bank)
Wolfgang Denk [Wed, 19 Jul 2006 12:49:35 +0000 (14:49 +0200)]
Fix support for PS/2 keyboard on TQM85xx boards
The PS/2 keyobard driver for the TQM85xx modules only supports the
internal DUART of the MPC85xx CPU. Since the MPC8560 doesn't
include a DUART, the TQM8560 modules can't be used with the PS/2
keyboard controller on the STK85xx board.
The PS/2 keyboard driver should work with the modules TQM8540,
TQM8541 and TQM8555, but it only has been tested on a TQM8540, yet.
Make sure the PS/2 controller on the STK85xx is programmed. Jumper
settings: X66 1-2, 9-10; X61 2-3
Wolfgang Denk [Wed, 19 Jul 2006 12:40:43 +0000 (14:40 +0200)]
Adjust filenames for USB update images on TRAB board.
During an automatic update via USB stick, U-Boot searches for
images with the name "firmware.img" and "kernel.img". This names
are now changed to "firmw_01.img" and "kernl_01.img". This is done,
to prevent updates of new boards (with the new macronics "c" step
flashes) with old, incompatible firmware or kernel versions.
Patch by Martin Krause, 21 Jun 2006
Wolfgang Denk [Wed, 19 Jul 2006 12:23:12 +0000 (14:23 +0200)]
Bugfix in VFD routine on TRAB board.
Make sure upper lext pixel can be set to blue, too
(so far only red was possible).
Patch by Martin Krause, 15 Feb 2006
Wolfgang Denk [Wed, 19 Jul 2006 12:13:02 +0000 (14:13 +0200)]
Fix some bugs in TRAB board flash driver.
- increase CFG_FLASH_ERASE_TOUT from 2 to 15 seconds
- use CFG_FLASH_WRITE_TOUT for programming instead of CFG_FLASH_ERASE_TOUT
- remove "Unlock Bypass" mode, because macronix flashes do not support
this mode officially
- fix flash reset command from 0x00FF to 0x00F0. 0x00FF is only specified
for Intel compatible flashes, not for AMD compatible.
Patch by Martin Krause, 15 Feb 2006
Wolfgang Denk [Wed, 19 Jul 2006 11:50:38 +0000 (13:50 +0200)]
Add support for TB5200 board
The TB5200 ("Tinybox") is a small baseboard for the TQM5200 module
integrated in a little aluminium case.
Patch by Martin Krause, 8 Jun 2006
Haiying Wang [Wed, 12 Jul 2006 14:48:05 +0000 (10:48 -0400)]
Add support for reading and writing mac addresses to or from ID EEPROM.
Added code for reading and writing Mac addresses to/from ID EEPROM(0x57).
With attached patch, we can use command "mac/mac read/mac save/"
to read and write EEPROM under u-boot prompt.
U-boot will calculate the checksum of EEPROM while bootup,
if it is right, then u-boot will check whether the mac address
of eTSEC0/1/2/3 is availalbe (non-zero).
If there is mac address availabe in EEPROM, u-boot will use it,
otherewise, u-boot will use the mac address defined in
MPC8641HPCN.h. This matches the requirement to set unique mac address
for each TSEC port.
Signed-off-by: Haiying Wang <haiying.wang@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com>
Bugfix in FEC initialisation:
All MII configuration is done via FEC1 registers. But MII_SPEED was
configured according to FEC used. So if only FEC2 was used, this caused
the real MII_SPEED register in FEC1 to stay uninitalised, what lead
to "mii_send STUCK!" messages. Fix: always configure MII_SPEED on FEC1
only.
Wolfgang Denk [Mon, 10 Jul 2006 21:07:28 +0000 (23:07 +0200)]
Major PCMCIA Cleanup to make code better readable and maintainable.
Notes:
- Board-dependend code for RPXLITE and RPXCLASSIC-based boards
placed to the drivers/rpx_pmcia.c file to avoid duplication.
Same for TQM8xx-based boards (drivers/tqm8xx_pmcia.c).
- drivers/i82365.c has been split into two parts located at
board/atc/ti113x.c and board/cpc45/pd67290.c (ATC and CPC45 are
the only boards using CONFIG_82365).
- Changes were tested for clean build and *very* *few* boards.
When tftp a non-exist file from the tftp server, u-boot will check
the link of all eth port. The original file will return wrong link
state on the no link ports.
signed-off-by: Jason Jin <Jason.Jin@freescale.com>
During the pci scan process, Some devices return bar_reponse with the
highest bytes 0, such as the pci bridge in uli1575 return bar_response
with 0xffffff, So the bar_size should be manually set under 64K.
Signed-off-by: Jason Jin <jason.jin@freescale.com>
projects / u-boot / log