Tuomas Tynkkynen [Fri, 20 Apr 2018 10:03:49 +0000 (13:03 +0300)]
rpi: Change load addresses to make more room for the kernel & DTB
As of Linux 4.16, a multiplatform AArch64 kernel with our distro config
takes 26M. The current space reservation leaves only 17M for the kernel
and if it goes over it, the initrd gets overwritten when loading the
kernel from the filesystem.
A similar problem happens on ARMv7 with the DTBs taken from the
downstream Raspberry Pi foundation kernel. I guess they compile them
with DT overlay support enabled which grows them just enough.
Fix both of these problems by rewriting the memory map, which now allows
kernels to be up to 36M and DTBs up to 1M. Also the comment block was
kind of obsolete ever since the introduction of AArch64 support and the
firmware-loaded DTB doesn't get placed at 0x100 anymore either, so that
is fixed as well.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com> Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Wed, 23 May 2018 20:24:51 +0000 (22:24 +0200)]
mmc: Unirqify bcm2835_sdhost and fix writes
The bcm2835 sdhost driver has a problem with "write multiple" commands.
It seems to boil down to the fact that the controller dislikes its FIFO
to get drained at the end of a block when a write multiple blocks command
is in flight.
The easy fix is to simply get rid of all the IRQ driven logic and make
the driver push as much data into the FIFO as it can. That way we never
drain and we never run into the problem.
Reported-by: Jan Leonhardt <jan@cyberdesigner.net> Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Fri, 13 Apr 2018 15:37:34 +0000 (17:37 +0200)]
rpi: Adjust fdt_addr_r to a sane address
Back in the old days, 0x100 was used as the address to pass the device tree
from firmware into the kernel. This has since changed to a more dynamic
location, so using 0x100 actually breaks more things than it helps with.
Let's move the device tree default location for distro boot to a more sane
place that gives us enough head room in low memory.
Reported-by: Tuomas Tynkkynen <tuomas@tuxera.com> Signed-off-by: Alexander Graf <agraf@suse.de>
Tom Rini [Thu, 10 May 2018 11:15:54 +0000 (07:15 -0400)]
.travis.yml: Further optimizations
- Xilinx aarch64 is caught in the general xilinx arm job, exclude from
the general aarch64 job.
- Give the generic aarch64 job a better name
- Re-sort the PowerPC jobs so that we can complete them a bit quicker.
Tom Rini [Thu, 10 May 2018 11:15:52 +0000 (07:15 -0400)]
at91: Minor tweaks to SPL logic for space savings on smartweb
- spl_board_init is empty on smartweb so drop that function
- When CONFIG_AT91SAM9_WATCHDOG is set we do not disable the watchdog in
SPL and instead let full U-Boot handle it. Instead of an empty
function just do not call a function.
Marek Vasut [Wed, 2 May 2018 10:09:23 +0000 (12:09 +0200)]
ARM: rmobile: Unify Gen2 Makefile entry
Drop per-SoC Makefile entries and replace them with one unified entry
now that the PFC tables are gone. Shuffle the Makefile around a bit
to make it more organized.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Mon, 30 Apr 2018 12:10:36 +0000 (14:10 +0200)]
ARM: rmobile: Update V2H Blanche
The V2H Blanche port was broken since some time. This patch updates
the V2H Blanche port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Michal Simek [Fri, 18 May 2018 11:15:08 +0000 (13:15 +0200)]
arm64: zynqmp: Use DWC3 generic driver and DM_USB
Remove harcoded XHCI lists and detect mode, speed based on DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Serial-changes: 2
- Remove also XHCI macros from hardware.h
- Remove additional new line in zcu106
Michal Simek [Fri, 18 May 2018 11:15:06 +0000 (13:15 +0200)]
usb: dwc3: Add generic DWC3 glue logic driver
By enabling BLK by default this is the next driver which needs to get
support for DM_USB. Adding generic DWC3 glue logic which only
parse nodes and read device mode. Based on it probe proper
host/peripheral DWC3 drivers for it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mugunthan V N [Fri, 18 May 2018 11:15:05 +0000 (13:15 +0200)]
usb: common: add support to get maximum speed from dt
Add support to get maximum speed from dt so that usb drivers
makes use of it for DT parsing.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
(rebase and fix errors) Reviewed-by: Simon Glass <sjg@chromium.org>
Mugunthan V N [Fri, 18 May 2018 11:15:04 +0000 (13:15 +0200)]
usb: dwc3: Add dwc3_init/remove with DM_USB
The patch is preparing dwc3 core for enabling DM_USB with peripheral
driver with using driver model support.
The driver will be bound by the DWC3 wrapper driver based on the
dr_mode device tree entry.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
(Remove dwc3-omap changes) Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds phy tranceiver driver for STM32 USB PHY
Controller (usbphyc) that provides dual port High-Speed
phy for OTG (single port) and EHCI/OHCI host controller
(two ports).
One port of the phy is shared between the two USB controllers
through a UTMI+ switch.
Seung-Woo Kim [Thu, 10 May 2018 01:52:15 +0000 (10:52 +0900)]
gadget: f_thor: update to support more than 4GB file as thor 5.0
During file download, it only uses 32bit variable for file size and
it limits maximum file size less than 4GB. Update to support more
than 4GB file with using two 32bit variables for file size as thor
protocol 5.0.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Seung-Woo Kim [Thu, 10 May 2018 01:52:14 +0000 (10:52 +0900)]
gadget: f_thor: fix filename overflow
The thor sender can send filename without null character and it is
used without consideration of overflow. Actually, character array
for filename is assigned with DEFINE_CACHE_ALIGN_BUFFER() and it
is bigger than size of memcpy, so there was no real overflow.
Fix filename overflow for code level integrity.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Preparation for Stratix 10 enablement. In ARM64, L2 cache controller is
accessed through processor registers. So, add CONFIG_SYS_L2_PL310 switch
conditional build in order this file can by shared across other SOCFPGAs.
Signed-off-by: Chin Liang See <chin.liang.see@intel.com> Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Tien Fong Chee [Tue, 5 Dec 2017 07:58:01 +0000 (15:58 +0800)]
ARM: socfpga: Add DRAM bank size initialization function
Add function for both multiple DRAM bank and single DRAM bank size
initialization. This common functionality could be used by every single
SOCFPGA board.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com> Tested-by: Ley Foon Tan <ley.foon.tan@intel.com>
Marek Vasut [Mon, 23 Apr 2018 20:49:31 +0000 (22:49 +0200)]
ARM: socfpga: Repair A10 EMAC reset handling
The EMAC reset and PHY mode configuration was never working on the
Arria10 SoC, fix this. This patch pulls out the common code into
misc.c and passes the SoC-specific function call in as a function
pointer.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <chin.liang.see@intel.com> Cc: Dinh Nguyen <dinguyen@kernel.org>
The A10 clock manager parsed DT bindings generated by Quartus the
bsp-editor to configure the A10 clocks. Sadly, those DT bindings
changed at some point. The clock manager patch used the old ones,
this patch replaces the bindings parser with one for the new set.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <chin.liang.see@intel.com> Cc: Dinh Nguyen <dinguyen@kernel.org>
Marek Vasut [Sat, 12 May 2018 09:56:10 +0000 (11:56 +0200)]
fdt: Add another Altera Arria10 clock init compatible
The DT bindings for the Arria10 clock init have changed, add another
compatible to make them work with U-Boot until a proper clock driver
gets written.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Tom Rini <trini@konsulko.com> Cc: Chin Liang See <chin.liang.see@intel.com> Cc: Dinh Nguyen <dinguyen@kernel.org>
Lukasz Majewski [Tue, 15 May 2018 14:26:43 +0000 (16:26 +0200)]
sandbox: tests: Add tests for mc34708 PMIC device
Following tests has been added for mc34708 device:
- get_test for mc34708 PMIC
- Check if proper number of registers is read
- Check if default (emulated via i2c device) value is properly read
- Check if value write/read operation is correct
- Perform tests to check if pmic_clrsetbits() is working correctly
Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Lukasz Majewski [Tue, 15 May 2018 14:26:38 +0000 (16:26 +0200)]
pmic: Rewrite the pmic command to not only work with single byte transmission
Up till now it was only possible to use 'pmic' command with a single byte
transmission.
The pmic_read|write functions has been replaced with ones, which don't need
the transmission length as a parameter.
Due to that it is possible now to read data from PMICs transmitting more
data than 1 byte at once (e.g. mc34708)
Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Chris Packham [Thu, 17 May 2018 12:12:04 +0000 (00:12 +1200)]
net: MVGBE don't automatically select PHYLIB
When Kconfig support was added for MVGBE it included automatically
selected PHYLIB support. But MVGBE does not need PHYLIB it will build
fine without it. Commit ed52ea507f12 ("net: add Kconfig for MVGBE")
should have been a no-op in terms of build size but because of the
selecting PHYLIB the openrd configs increased in size.
Remove the automatic selection of PHYLIB, boards that need it will have
already enabled it in their config header file.
Fixes: commit ed52ea507f12 ("net: add Kconfig for MVGBE") Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Stefan Roese <sr@denx.de>
projects / u-boot / log