York Sun [Thu, 7 Sep 2017 17:12:32 +0000 (10:12 -0700)]
armv8: fsl-layerscape: Fix MC reserved memory calculation
In case high region memory doesn't have enough space for Management
Complex (MC), the return value should indicate a failure so the
caller can handle it accordingly.
Signed-off-by: York Sun <york.sun@nxp.com> Reported-by: Ebony Zhu <ebony.zhu@nxp.com>
Ran Wang [Mon, 4 Sep 2017 10:46:53 +0000 (18:46 +0800)]
armv7: Add workaround for USB erratum A-009798
The default setting for USB High Speed Squelch Threshold results
in a threshold close to or lower than 100mV. This leads to Receive
Compliance test failure for a 100mV threshold.
Shift the threshold from ~100mV towards ~130mV by setting SQRXTUNE
to 0x0 to pass USB High Speed Receiver Sensitivity Compliance test.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com> Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options] Reviewed-by: York Sun <york.sun@nxp.com>
Ran Wang [Mon, 4 Sep 2017 10:46:52 +0000 (18:46 +0800)]
armv7: Add workaround for USB erratum A-009008
USB High Speed (HS) EYE Height Adjustment
USB HS speed eye diagram fails with the default value at
many corners, particularly at a high temperature
Optimal eye at TXREFTUNE value to 0x9 is observed, change
set the same value.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com> Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options] Reviewed-by: York Sun <york.sun@nxp.com>
Ran Wang [Mon, 4 Sep 2017 10:46:49 +0000 (18:46 +0800)]
armv8: Add workaround for USB erratum A-009798
The default setting for USB High Speed Squelch Threshold results
in a threshold close to or lower than 100mV. This leads to Receiver
Compliance test failure for a 100mV threshold.
Shift the threshold from ~100mV towards ~130mV by setting SQRXTUNE
to 0x0 to pass USB High Speed Receiver Sensitivity Compliance test.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com> Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options] Reviewed-by: York Sun <york.sun@nxp.com>
Ashish Kumar [Thu, 31 Aug 2017 10:42:55 +0000 (16:12 +0530)]
armv8: ls1088aqds: Add support of LS1088AQDS
This patch add support of LS1088AQDS platform.
The LS1088A QorIQTM Development System (QDS) is a high-performance
computing, evaluation, and development platform that supports the
LS1088A QorIQ Architecture processor.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Ashish Kumar [Thu, 31 Aug 2017 10:42:54 +0000 (16:12 +0530)]
armv8: ls1088ardb: Add support for LS1088ARDB platform
LS1088A is an ARMv8 implementation. The LS1088ARDB is an evaluatoin
platform that supports the LS1088A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Alison Wang <alison.wang@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
[YS: Disabled NAND in board header file] Reviewed-by: York Sun <york.sun@nxp.com>
WIP: disable NAND for LS1088ARDB
Ashish Kumar [Thu, 31 Aug 2017 10:42:53 +0000 (16:12 +0530)]
armv8: ls1088a: Add NXP LS1088A SoC support
LS1088A is compliant with the Layerscape Chassis Generation 3 with
eight ARM v8 Cortex-A53 cores in 2 cluster, CCI-400, one 64-bit DDR4
SDRAM memory controller with ECC, Data path acceleration architecture
2.0 (DPAA2), Ethernet interfaces (SGMIIs, RGMIIs, QSGMIIs, XFIs),
QSPI, IFC, PCIe, SATA, USB, SDXC, DUARTs etc.
Signed-off-by: Alison Wang <alison.wang@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
[YS: Revised commit message] Reviewed-by: York Sun <york.sun@nxp.com>
Ran Wang [Mon, 28 Aug 2017 02:40:33 +0000 (10:40 +0800)]
armv8: fsl: Use correct conditional compile for ls1012a
According current code base, CONFIG_LS1012A should be
CONFIG_ARCH_LS1012A, or function fsl_fdt_disable(blob) will be
wrongly called to disable all dwc3 USB nodes on LS1012A, which
cause Linux USB function stop working at all.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Priyanka Jain [Thu, 24 Aug 2017 11:12:43 +0000 (16:42 +0530)]
drivers:net:fsl-mc: Update MC address calculation
Update MC address calculation as per MC design requirement of address
as least significant 512MB address of MC private allocated memory,
i.e. address should point to end address masked with 512MB offset in
private DRAM block.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com>
[YS: reformatted commit message] Reviewed-by: York Sun <york.sun@nxp.com>
Adds header address for PPA to be validated during ESBC phase for
ARCH_LS2088 and QSPI_BOOT. Moves sec_init prior to ppa_init(). It
must be initialized before the PPA.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[YS: revised commit message] Reviewed-by: York Sun <york.sun@nxp.com>
Sumit Garg [Wed, 16 Aug 2017 11:13:28 +0000 (07:13 -0400)]
SECURE_BOOT: Unify memory map for Layerscape based platforms
Unify memory map for Layerscape based platforms. This patch includes
changes in bootscript, bootscript header and PPA header addresses
change as per unified memory map.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Ashish Kumar [Fri, 11 Aug 2017 05:39:14 +0000 (11:09 +0530)]
fsl-layerscape: Consolidate registers space defination for CCI-400 bus
CoreLink Cache Coherent Interconnect (CCI) provides full cache
coherency between two clusters of multi-core CPUs and I/O coherency
for devices and I/O masters.
This patch add new config option SYS_FSL_HAS_CCI400 and moves
existing register space definaton of CCI-400 bus to fsl_immap to be
shared. CONFIG_SYS_CCI400_ADDR is replaced with SYS_CCI400_OFFSET
in Kconfig.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[YS: revised commit message, squashed patches for armv8 and armv7] Reviewed-by: York Sun <york.sun@nxp.com>
Bin Meng [Sun, 10 Sep 2017 12:12:53 +0000 (05:12 -0700)]
cmd: ide: Make the first device the default one
At present the IDE device number is initialized to -1, which means
we cannot type "ide read" command before setting the device number
via "ide device #".
For convenience, let's set the first device as the default one.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Sun, 10 Sep 2017 12:12:51 +0000 (05:12 -0700)]
block: ide: Fix block read/write with driver model
This converts the IDE driver to driver model so that block read and
write are fully functional.
Fixes: b7c6baef ("x86: Convert MMC to driver model") Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Fri, 8 Sep 2017 17:12:16 +0000 (13:12 -0400)]
env: Migrate CONFIG_ENV_AES to Kconfig and deprecate
The underlying implementation for ENV_AES has security complications and
is not recommended for use. Please see CVE-2017-3225 and CVE-2017-3226
for more details. Mark this as deprecated now and delete this in the
medium term if no one comes forward to re-work the support.
Chris Packham [Mon, 28 Aug 2017 08:50:45 +0000 (20:50 +1200)]
usb: net: migrate CONFIG_USB_HOST_ETHER to Kconfig
CONFIG_USB_HOST_ETHER is the framework that the drivers are dependent on
USB_HOST_ETHER. Use this as a menu and move the existing LAN75XX and
LAN78XX options under new menu. Finally update the defconfigs that need
CONFIG_USB_HOST_ETHER.
Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Kever Yang [Fri, 8 Sep 2017 03:00:54 +0000 (11:00 +0800)]
rockchip: enable SPL_SYSRESET config for all Rockchip SoCs
With Makefiles testing for $(SPL_TPL_)SYSRESET, we need SPL_SYSRESET
for do_reset() in SPL for Rockchip SoCs.
References: 87c16d4 "drivers: spl: consistently use the $(SPL_TPL_) macro" Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Wed, 6 Sep 2017 07:58:25 +0000 (15:58 +0800)]
rockchip: rk3328: fix syscon id table
syscon id table need a dummy member as NULL ending, or else system
will panic while try to match a compatible in this table as a list.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Disable CONFIG_ARCH_FIXUP_FDT_MEMORY to prevent U-Boot from modifying
the memory {} nodes in the DT passed to the Linux kernel. The R8A779x
DT contains multiple memory {} nodes, while U-Boot only modifies the
first one and stuffs all the memory entries into it, which is wrong.
Disabling CONFIG_ARCH_FIXUP_FDT_MEMORY is the least intrusive way to
fix the issue this close to the release, while the real fix is to
extend the fdt_fixup_memory_banks() to handle multiple memory nodes
in DT.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Tue, 5 Sep 2017 13:11:14 +0000 (15:11 +0200)]
ARM: rmobile: Fix SD divider settings on Gen3
On RCar M3 and on RCar H3 newer than and not including ES1.0, the SD clock
must be divided by 4 rather than 2 because a hardware workaround present
only in the H3 ES1.0 has been removed from these chips. U-Boot currently
only supports M3 and H3 ES 2.0 and newer, so configure the SD pre-divider
to 4 to prevent SD instability.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tom Rini [Mon, 21 Aug 2017 02:40:01 +0000 (22:40 -0400)]
net: nfs: Drop CONFIG_NFS_READ_SIZE
In the general case, CONFIG_NFS_READ_SIZE is unchanged from the default
of 1024. There are in fact no in-tree users that increase this size.
Adjust the comment to reflect what could be done in the future in
conjunction with CONFIG_IP_DEFRAG.
Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Madalin Bucur [Fri, 18 Aug 2017 08:35:24 +0000 (11:35 +0300)]
net: phy: realtek: fix enabling of the TX-delay for RTL8211F
The old logic always enabled the TX-delay when the phy-mode was set to
PHY_INTERFACE_MODE_RGMII. With this patch we enable the TX delay for
PHY_INTERFACE_MODE_RGMII_ID and PHY_INTERFACE_MODE_RGMII_TXID and
disable it for PHY_INTERFACE_MODE_RGMII.
Based on a similar change made in the Linux Realtek PHY driver
by Martin Blumenstingl <martin.blumenstingl@googlemail.com>.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Acked-by: York Sun <york.sun@nxp.com>
This is a workaround for Raspberry Pi boot failures seen when passing on
the device tree provided by the Raspberry Pi firmware at boot. Without
CONFIG_OF_EMBED, we just get stuck at "Starting kernel ..." when we try
to boot Linux with this device tree.
Signed-off-by: Paul Barker <pbarker@toganlabs.com> Cc: Simon Glass <sjg@chromium.org> Tested-by: Jonathan Gray <jsg@jsg.id.au> Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 5 Sep 2017 07:53:58 +0000 (01:53 -0600)]
env: Fix operation of 'make environ'
This was broken by the recent environment refactoring. Specifically:
$ make environ
scripts/Makefile.build:59: tools/environ/Makefile: No such file or directory
make[1]: *** No rule to make target 'tools/environ/Makefile'. Stop.
make: *** [Makefile:1469: environ] Error 2
Fix this by updating the Makefile and adjusting the #include filesnames in
two C files.
Fixes: ec74f5f (Makefile: Rename 'env' target to 'environ') Reported-by: Måns Rullgård <mans@mansr.com> Signed-off-by: Simon Glass <sjg@chromium.org>
Sam Protsenko [Fri, 1 Sep 2017 12:42:03 +0000 (15:42 +0300)]
usb: gadget: g_dnl: Sync internal SN variable with env
Since commit 842778a09104 ("usb: gadget: g_dnl: only set iSerialNumber
if we have a serial#") "fastboot devices" stopped to show correct device
serial number for TI boards, showing this line instead:
???????????? fastboot
This is because serial# env variable could be set after g_dnl gadget was
initialized (e.g. by using env_set() in the board file).
To fix this, let's update internal serial number variable (g_dnl_serial)
when "serial#" env var is changed.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Cc: Felipe Balbi <felipe.balbi@linux.intel.com> Tested-by: Heiko Schocher <hs@denx.de> Acked-by: Łukasz Majewski <lukma@denx.de> Reviewed-by: Marek Vasut <marex@denx.de>
Tom Rini [Tue, 5 Sep 2017 18:01:29 +0000 (14:01 -0400)]
env: Fix out of tree building of tools-all
With the move of environment code from common/ to env/ a number of
changes needed to be made to various make targets. We missed updating
some of the files required for out of tree builds of the tools. Correct
the 'environ' target to know that we need to work under tools/env/ still
(not tools/environ/) and then update the wrappers in env_attr.c and
env_flags.c to point to the new correct file.
Reported-by: Peter Robinson <pbrobinson@gmail.com> Tested-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Kever Yang [Thu, 27 Jul 2017 12:38:52 +0000 (20:38 +0800)]
rockchip: firefly-rk3399: enable ATF and dwmmc
enable the ATF option and SDCard in defconfig.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Fri, 25 Aug 2017 11:22:00 +0000 (13:22 +0200)]
rockchip: timer: fix U_BOOT_DRIVER name
When I originally added this driver, I did some careless (and in
retrospect: mindless) copy & paste for the U_BOOT_DRIVER structure
skeletion... unfortunately, the 'arc_timer' string was committed
and slipped through all reviews.
This fixes the U_BOOT_DRIVER name to read 'rockchip_rk3368_timer'
(as originally intended).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reported-by: Artturi Alm <artturi.alm@gmail.com>
Wadim Egorov [Mon, 21 Aug 2017 11:36:57 +0000 (13:36 +0200)]
rockchip: rk3288: Add reset reason detection
Sometimes it's helpful to know the reset reason caused in the SoC.
Add reset reason detection for the RK3288 SoC.
This will set an environment variable which represents the reset reason.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Marek Vasut [Mon, 28 Aug 2017 12:13:11 +0000 (14:13 +0200)]
ARM: rmobile: Add missing IPSR18 bits to R8A7795 PFC
The IPSR18 register bits were missing from the R8A7795 ES2.0+ PFC
tables, which triggered a BUG() in sh_pfc driver. This is because
of an out-of-bounds access to the pinmux_gpios[] array in the PFC
tables, which was too short due to the missing IPSR18 bits.
Marek Vasut [Mon, 28 Aug 2017 12:12:34 +0000 (14:12 +0200)]
ARM: rmobile: Replace CONFIG_RAVB with CONFIG_RENESAS_RAVB in boards
The configuration option name is the later, so replace usage of
CONFIG_RAVB in board files with CONFIG_RENESAS_RAVB , otherwise
the RAVB pinmux is not set and ethernet does not work.
Niko Mauno [Thu, 3 Aug 2017 06:53:24 +0000 (09:53 +0300)]
splash_source: Verify FIT magic
Before reading entire FIT image, add sanity check by testing image
header against FDT_MAGIC. This should help avoid problems in situations
where FIT is not yet available from storage device, for example when
performing initial programming of device.
Cc: Anatolij Gustschin <agust@denx.de> Acked-by: Tomas Melin <tomas.melin@vaisala.com>
video: ipuv3_fb: skip IPU shutdown if IPU was not enabled before
Boards can skip display interface init using board_video_skip().
If display interface was not initialized (e.g. no ipuv3 framebuffer
registered or IPU clock disabled), booting Linux stops due to the
crash in IPU shutdown function, when accessing IPU registers.
Check IPU clock and skip shutdown if clock is not enabled.
Clemens Gruber [Sun, 3 Sep 2017 17:17:10 +0000 (19:17 +0200)]
crypto/fsl: fix obj-yy in Makefile
When enabling CONFIG_CMD_BLOB and/or CONFIG_CMD_DEKBLOB, the build fails
with a linker error:
...
LD u-boot
arch/arm/mach-imx/built-in.o: In function `blob_encap_dek':
/home/clemens/dev/u-boot/arch/arm/mach-imx/cmd_dek.c:46: undefined
reference to `blob_dek'
This is due to an error in the Makefile, resulting in obj-yy/obj-yn/..
and fsl_blob.o is therefore not linked.
Fix it by splitting it up into two obj-y lines.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Philipp Tomsich [Tue, 29 Aug 2017 09:47:16 +0000 (11:47 +0200)]
gitignore: add intermediates from libfdt build
Since ee95d10 (fdt: Build the new python libfdt module), a number of
additional files are auto-generated/installed into the tools directory.
List these in .gitignore to suppress having them listed as untracked.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
References: ee95d10 (fdt: Build the new python libfdt module) Reviewed-by: Simon Glass <sjg@chromium.org>
Hannes Schmelzer [Fri, 18 Aug 2017 12:41:14 +0000 (14:41 +0200)]
fdt: fix 'prop (...) not found!' error in 'fdt set' command
This commit brings things back to the well known working state of the
command.
-
With commit 9620d87259572ef21f0df60988d9a932ca673779
(cmd/fdt: support single value replacement within an array)
there was an error introduced modifying (inserting) a property to a
device-tree node.
fdt_getprop(...) returnes a len with -1 for a non-existing property, but
a memcpy with len -1 isn't a good idea and things went wrong (crash).
-
Some times later Tom did repair this
with commit 99bb38e2cce9d99238458e0f6d1880c6d2e80a4d
(fdt: Check for NULL return from fdt_getprop in 'fdt set')
This repairs the crash but the behaviour of the command isn't like
before, it makes it impossible to insert a property.
-
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 5 Aug 2017 21:45:53 +0000 (15:45 -0600)]
dm: Add migration plan for CONFIG_BLK
The CONFIG_BLK conversion involves quite invasive changes in the U-Boot
code, with #ifdefs and different code paths. We should try to move over to
this soon so we can drop the old code.
Set a deadline of 9 months for this work, rounded up to the next release.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
omap3: evm: Fixes for CONFIG_NAND, SPL_OS_BOOT, USB, and environment
- Pass MTDPARTS kernel arguments to kernel
- Use Kconfig CONFIG_NAND instead of CONFIG_SYS_EXTRA_OPTIONS="NAND"
- Call 'usb_stop' on kernel start
- Update Falcon mode setup to match other OMAP3 boards
- Use "uEnv.txt" as boot script instead of "boot.scr"
Bin Meng [Sat, 2 Sep 2017 15:15:36 +0000 (08:15 -0700)]
nvme: Fix potential sign extension issue in nvme_blk_rw()
"lbas" with type "u16" (16 bits, unsigned) is promoted in
"lbas << ns->lba_shift" to type "int" (32 bits, signed), then
sign-extended to type "unsigned long long" (64 bits, unsigned).
If "lbas << ns->lba_shift" is greater than 0x7FFFFFFF, the upper
bits of the result will all be 1.
Fix it by casting "lbas" to "u32".
Reported-by: Coverity (CID: 166730) Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Lukasz Majewski [Sun, 27 Aug 2017 11:46:22 +0000 (13:46 +0200)]
fix: fw_env: Prevent writing error message on special files, which don't support fsync
According to fsync specification [1] some special files (e.g., a pipe, FIFO,
or socket) don't support synchronization and return either EROFS or EINVAL.
On the linux side the sys_fsync -> do_fsync() checks if the requested file
has f_op->fsync defined. If not it returns EINVAL [2].
This commit prevents writing error messages for files (devices), which
do not support fsync().
Jonathan Gray [Sun, 27 Aug 2017 10:45:14 +0000 (20:45 +1000)]
bch: don't use __BSD_VISIBLE to test for fls
Commit 4ecc988301bc8e981e6d7538c57cdb3aa82f7c1d assumes fls is in libc
if __BSD_VISIBLE is defined. This appears to only be true on FreeBSD
and DragonFlyBSD. OpenBSD defines __BSD_VISIBLE and does not have fls
in strings.h/libc.
Switch the test for __BSD_VISIBLE to one for __DragonFly__ and
__FreeBSD__ to unbreak the build on OpenBSD.
This commit removes definitions of CONFIG_SYS_BARGSIZE defined to be
equal to CONFIG_SYS_CBSIZE in numerous configuration files.
We remove such definitions in two situations:
- CONFIG_SYS_CBSIZE is otherwise not defined in the board
configuration file, which means the default value of
CONFIG_SYS_CBSIZE == 256 applies. In this case, the default value
of CONFIG_SYS_BARGSIZE == 512 (common/image.c) is suitable, as it is
larger.
- CONFIG_SYS_CBSIZE is defined in the board configuration file, but
to a value equal or less than 512. In this case, the default value
of CONFIG_SYS_BARGSIZE == 512 (common.image.c) is suitable, as it
is equal or larger.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Reviewed-by: Tom Rini <trini@konsulko.com>
projects / u-boot / log