Joel Fernandes [Wed, 4 Sep 2013 23:55:14 +0000 (18:55 -0500)]
usb: gadget: Fix data aborts during USB ethernet boot
As seen on GCC 4.6 Linaro compiler, control_req buffer is not aligned
on 4 byte boundaray causing data aborts in eth_setup -> conf_buf
during dhcp boot over usb_ether. Fix the issue my aligning control_req
buffer using DEFINE_CACHE_ALIGN_BUFFER.
Tested on am335x_evm platform (beaglebone).
Applies on 2013.10-rc1 branch.
Cc: Tom Rini <trini@ti.com> Cc: Marek Vasut <marex@denx.de> Signed-off-by: Joel Fernandes <joelf@ti.com>
This patch makes the necessary changes for making use of
I2S0 channel instead of I2S1 channel on smdk board. This
changes are done to maintain the uniformity to use I2S0 channel.
Tom Rini [Tue, 24 Sep 2013 13:05:08 +0000 (09:05 -0400)]
cmd_pxe.c: Pass along 'cmdtp' to do_bootm()/do_bootz()
When we call do_bootm() with a vmlinuz, this would lead to a NULL
pointer dereference, and after talking with Wolfgang the right thing to
do here for now is to make sure that we pass cmdtp to these functions
rather than NULL.
Reported-by: Steven A. Falco <stevenfalco@gmail.com> Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Mon, 23 Sep 2013 18:20:37 +0000 (14:20 -0400)]
cmd_bootm.c: Only pass BOOTM_STATE_OS_CMDLINE on PowerPC/MIPS
In 5c427e4 we pass BOOTM_STATE_OS_CMDLINE as part of the bootm states to
run, on all arches. However, this is only valid / useful on PowerPC and
MIPS, and causes a problem on ARM where we specifically do not use it.
Rather than make this state fake pass like we do for GO on some arches
(which need updating to use the GO state), we should just not pass
CMDLINE except when it may be used, like before.
Tested-by: Dan Murphy <dmurphy@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
Fix wrong sdhci host control register read and write
The patch fixes the improper read and write of sdhci
host control register for sdma transfer.
The problem comes when reading and writing 1 byte long
host control register with the sdhci_readl() and
sdhci_writel(). The misuse of these functions overwrite
the value of the next registers which are in 4 bytes boundary.
This patch replaces four byte register read/write functions
with one byte read/write ones. Beside, it eliminates
unnecessary bit operation. i.e. or-ing zero against a variable.
Without those it's very easy to make mistakes when for instance
the 'size' field is more than just a constant.
Signed-off-by: Mischa Jonker <mjonker@synopsys.com> Cc: Alexey Brodkin <abrodkin@synopsys.com> Cc: Marek Vasut <marex@denx.de> Cc: Anton Staaf <robotboy@chromium.org> Cc: Tom Rini <trini@ti.com> Cc: Wolfgang Denk <wd@denx.de>
mmc/dw_mmc: Allocate the correct amount of descriptors
This fixes two issues:
* a descriptor was allocated for every block, while a descriptor can
take 8 blocks
* there was an off-by-one error in the descriptor preparation: there
were two last descriptors, one with length==0
In dwmci_prepare_data, the descriptors are allocated for DMA transfer.
These are allocated using the ALLOC_CACHE_ALIGN_BUFFER. This macro uses
the stack to allocate these descriptors. This becomes a problem if the
DMA transfer continues after the processor leaves the function in which
the descriptors were allocated.
Therefore, I have moved the allocated of the buffers up one level, to
dwmci_send_cmd(). The DMA transfer should be complete when leaving this
function.
Paul Burton [Mon, 9 Sep 2013 14:30:26 +0000 (15:30 +0100)]
mmc: don't support write & erase for SPL builds
For SPL builds this is just dead code since we'll only need to read.
Eliminating it results in a significant size reduction for the SPL
binary, which may be critical for certain platforms where the binary
size is highly constrained.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Wolfgang Denk [Tue, 17 Sep 2013 09:24:06 +0000 (11:24 +0200)]
SPDX: fix IBM-pibs license identifier
The SPDX License List version 1.19 now contains an official entry for
the IBM-pibs license. However, instead of our suggestion "ibm-pibs",
the SPDX License List uses "IBM-pibs", with the following rationale:
"The reason being that all other SPDX License List short identifiers
tend towards using capital letters unless spelling a word. I'd prefer
to be consistent to this end".
Mark Langsdorf [Tue, 10 Sep 2013 20:14:56 +0000 (15:14 -0500)]
part_efi: make sure the gpt_pte is freed
the gpt_pte wasn't being freed if it was checked against an invalid
partition. The resulting memory leakage could make it impossible
to repeatedly attempt to load non-existent files in a script.
Also, downgrade the message for not finding an invalid partition
from a printf() to a debug() so as to minimize message spam in
perfectly normal situations.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Netconsole calls eth_halt() before giving control to another operating
system.
But the state machine of netconsole don't take it into account.
Thus, netconsole calls network functions of an halted network device,
making the whole system freeze.
Rather than modifying the state machine of netconsole, we just unregister
the current network device before booting. It does work because
nc_send_packet() verifies that the current network device is not null.
Paul Burton [Fri, 6 Sep 2013 10:23:55 +0000 (11:23 +0100)]
bootm: use BOOTM_STATE_OS_CMDLINE flag for plain bootm
A plain bootm used to call the architecture specific boot function with
no flags, but was modified by commit 35fc84fa "Refactor the bootm
command to reduce code duplication" to call the architecture specific
boot function multiple times with various flags in sequence. The
BOOTM_STATE_OS_CMDLINE flag was not used, indeed it seems that at least
ARM prepares the command line on BOOTM_STATE_OS_PREP. However on MIPS
since commit 59e8cbdb "MIPS: bootm: refactor initialisation of kernel
cmdline" the command line is not prepared in response to a
BOOTM_STATE_OS_PREP flag, only on BOOTM_STATE_OS_CMDLINE or a call with
no flags. The end result is that a combination of those 2 commits leads
to MIPS boards booting kernels with no command line arguments.
An extra invocation of the architecture specific boot function with
BOOTM_STATE_OS_CMDLINE fixes this.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Paul Burton [Wed, 4 Sep 2013 15:12:26 +0000 (16:12 +0100)]
mmc: size optimization when !CONFIG_MMC_SPI
When CONFIG_MMC_SPI is not enabled, the MMC_MODE_SPI capability can
never be set. However there is code in mmc.c which uses the
mmc_host_is_spi macro to check that capability & act accordingly. If we
expand that macro to 0 when CONFIG_MMC_SPI is not set (since it will
always be 0 at runtime anyway) then the compiler can optimize away the
SPI-specific code paths in mmc.c.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Lubomir Popov [Wed, 14 Aug 2013 15:59:18 +0000 (18:59 +0300)]
ARM: OMAP: Enable 8-bit eMMC access for OMAP4/5/DRA7xx
Enable 8-bit host capability for HSMMC2 and/or HSMMC3. CONFIG_HSMMC2_8BIT
(for OMAP4/5/DRA7xx) and/or CONFIG_HSMMC3_8BIT (for DRA7xx only) must be
defined in the board header if an 8-bit eMMC device is connected to the
corresponding port.
Fix the "No status update" error that appeared for eMMC devices by
inserting a 20 us delay between writing arguments and command. This
solution has been proposed by Michael Cashwell <mboards@prograde.net>.
"mmc_send_cmd: timeout: No status update" error sometimes happens in
omap_hsmmc driver func mmc_send_cmd() when the MMC controller card
identification and selection sequence is executed for eMMC on OMAP4
boards.
It happens due to incorrect execution of CMD line reset procedure
for OMAP4. Because CMD(DAT) lines reset procedures are slightly
different for OMAP3 and OMAP4(AM335x,OMAP5,DRA7xx).
According to OMAP3 TRM:
Set SRC(SRD) bit in MMCHS_SYSCTL register to 0x1 and wait until
it returns to 0x0.
According to OMAP4(AM335x,OMAP5,DRA7xx) TRMs, CMD(DATA) lines reset
procedure steps must be as follows:
1. Initiate CMD(DAT) line reset by writing 0x1 to SRC(SRD) bit in
MMCHS_SYSCTL register (SD_SYSCTL for AM335x).
2. Poll the SRC(SRD) bit until it is set to 0x1.
3. Wait until the SRC(SRD) bit returns to 0x0
(reset procedure is completed).
Unfortunately, at present omap_hsmmc driver has support only for
OMAP3. And as result step #2 is missing for OMAP4(AM335x,OMAP5,DRA7xx).
This sometimes leads to the fact that the waiting loop which is
required in step #3 does not executed, because SRC bit does not set
yet (at the moment of checking a condition of a loop execution).
And as a result this can cause to timeout error when sending a
next command.
In the particular case (working with eMMC witch do not respond to
some SD specific command) due to incorrect reset sequence after
command SD_CMD_SEND_IF_COND which finished with CTO flag within
64 clock cycles, the next command MMC_CMD_APP_CMD leads to a
timeout error within 1s.
So, extend CMD(DATA) lines reset procedure in func
mmc_reset_controller_fsm() by adding the missing step #2 for
OMAP4+/AM335x boards.
Tom Rini [Tue, 10 Sep 2013 13:51:44 +0000 (09:51 -0400)]
Revert "standalone-examples: support custom GCC lib"
After further testing, this patch has two problems. First,
examples/standalone/Makefile was already inherting PLATFORM_LIBS from
the top-level Makefile so this lead to duplicating the private libgcc.
Second, currently the private libgcc has a reference to 'hang' that is
not being fulfilled.
Albert ARIBAUD [Wed, 11 Sep 2013 13:52:51 +0000 (15:52 +0200)]
Merge and reformat boards.cfg and MAINTAINERS
Put all informations about targets, including state (active or
orphan) and maintainers, in boards.cfg; remove MAINTAINERS;
adjust the build system accordingly.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
arm:goni:mmc: Add sd card detection and initialization.
This change allow to use sd card on Goni the same like mmc 0.
SD card is mmc dev 1, so it can be used like this: "fatls mmc 1:2".
SD card is inited even if eMMC initialization fails.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> CC: Minkyu Kang <mk7.kang@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
As per new convention ARCH_CPU_DTS is not defined in "dtc/Makefile".
Hence Arndale comilation is failing. Fix this by adding proper include
file in "board/samsung/dts/exynos5250-arndale.dts".
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
York Sun [Tue, 20 Aug 2013 22:09:43 +0000 (15:09 -0700)]
powerpc/mpc85xx: Add workaround for erratum A-005125
In a very rare condition, a system hang is possible when the e500 core
initiates a guarded load to PCI / PCIe /SRIO performs a coherent write
to memory. Please refer to errata document for more details. This erratum
applies to the following SoCs and their variants, if any.
powerpc/mpc85xx: Fix the I2C bus speed error on p1022
The source clock frequency of I2C bus on p1022 is the platform(CCB)
clock, not CCB/2. The wrong source clock frequency leads to wrong
I2C bus speed setting. so, fixed it.
Stefan Roese [Mon, 26 Aug 2013 10:08:48 +0000 (12:08 +0200)]
ppc4xx: Fix GPIO handling in lwmon5 and lcd4_lwmon5 BSP
LCD4 needs a slightly different GPIO configuration than the
original LWMON5 variant. GPIO49 needs to be configured to a
default output value of 0 (permanent voltage supply).
Additionally lcd4 also needs to enable the LSB transmitter.
Rob Herring [Sat, 24 Aug 2013 15:10:54 +0000 (10:10 -0500)]
ahci: convert to use libata functions and definitions
libata already has similar functions as implemented in the ahci code.
Refactor the code to use the libata variants and remove the dependency on
ata.h. Convert some defines to use the version from libata.h. Also, remove
some unnecessary memset's of bss data.
This is a step toward hopefully merging ahci.c and dw_ahsata.c which are
essentially the same driver.
Signed-off-by: Rob Herring <rob.herring@calxeda.com> Reviewed-by: Tom Rini <trini@ti.com>
Rob Herring [Sat, 24 Aug 2013 15:10:51 +0000 (10:10 -0500)]
ahci: move link bring-up handling to separate function
Move the link bring-up handling to a separate weak function in order to
allow platforms to override it. This is needed on highbank platform which
needs special phy handling.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Richard Gibbs [Sat, 24 Aug 2013 15:10:47 +0000 (10:10 -0500)]
ahci: use ports implemented map instead of num_ports
The AHCI driver was incorrectly using the Capabilities register NP (number
of ports) field to determine which ports to activate. This commit changes
it to correctly use the PORTS_IMPL register as a port map.
Signed-off-by: Richard Gibbs <richard.gibbs@calxeda.com> Reviewed-by: Tom Rini <trini@ti.com>
fs: fat: don't call disk_write with zero sector num
In the set_cluster() function, it will convert the buffer size to sector
numbers. Then call disk_write() to write by sector.
For remaining buffer, the size is less than a sector, call disk_write()
again to write them in one sector.
But if the total buffer size is less then one sector, the original code
will call disk_write() with zero sector number. It is unnecessary.
So this patch fix this. Now it will not call disk_write() if total buffer size
is less than one sector.
Jeroen Hofstee [Sat, 10 Aug 2013 15:16:50 +0000 (17:16 +0200)]
compiler_gcc: do not redefine __gnu_attributes
gcc allows extensions to be non compiler specific by defining
__* macros for the attributes supported by gcc. Having a
different definition causes many warnings during the build
(cdefs.h on FreeBSD uses __attribute((__pure__)) where u-boot
uses __attribute__((pure)) for example). Do not redefine
these macros to suppress these warnings.
This patch ignores the checkpatch warning:
WARNING: __packed is preferred over __attribute__((packed))
Chin Liang See [Wed, 7 Aug 2013 15:08:03 +0000 (10:08 -0500)]
socfpga: Creating driver for Reset Manager
Consolidating reset code into reset_manager.c. Also
separating reset configuration for virtual target and
real hardware Cyclone V development kit
Signed-off-by: Chin Liang See <clsee@altera.com> Reviewed-by: Pavel Machek <pavel@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Pavel Machek <pavel@denx.de> Cc: Dinh Nguyen <dinguyen@altera.com> Cc: Tom Rini <trini@ti.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Chin Liang See [Wed, 7 Aug 2013 15:06:56 +0000 (10:06 -0500)]
socfpga: Adding configuration for development kit
Separating the configuration file for Virtual
Target and real hardware Cyclone V development kit
Signed-off-by: Chin Liang See <clsee@altera.com> Reviewed-by: Pavel Machek <pavel@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Pavel Machek <pavel@denx.de> Cc: Dinh Nguyen <dinguyen@altera.com> Cc: Tom Rini <trini@ti.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Remove ARM eabi exception handling tables (for frame unwinding).
AFAICT, u-boot stubs away the frame unwiding routines, so the tables will
more or less just consume space. It should be OK to remove them.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Wu, Josh [Fri, 23 Aug 2013 07:09:05 +0000 (15:09 +0800)]
mtd: atmel_nand: pmecc: fix bug fail to correct bit error in 1024-bytes sector
The PMECC use BCH algorithm to correct error. In BCH algorithm, the
primitive polynomial value is GF(2^13) for 512-bytes sector size. And it is
GF(2^14) for 1024-bytes sector size.
This patch will choose correct degree of the remainders (13 or 14) for
different sector size.
Tested in AT91SAM9X5-EK with MLC nand flash.
More detail can be refered to section 5.4.1 of:
AT91SAM ARM-based Embedded MPU Application Note
<http://www.atmel.com/Images/doc11127.pdf>
Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Kees Cook [Fri, 16 Aug 2013 14:59:16 +0000 (07:59 -0700)]
bootm: allow correct bounds-check of destination
While nothing presently examines the destination size, it should at
least be correct so that future users of sys_mapmem() will not be
surprised. Without this, it might be possible to overflow memory.
Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
Kees Cook [Fri, 16 Aug 2013 14:59:14 +0000 (07:59 -0700)]
lzma: correctly bounds-check output buffer
The output buffer size must be correctly passed to the lzma decoder or
there is a risk of overflowing memory during decompression. Switching
to the LZMA_FINISH_END mode means nothing is left in an unknown state
once the buffer becomes full.
Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
Kees Cook [Fri, 16 Aug 2013 14:59:11 +0000 (07:59 -0700)]
sandbox: add compression tests
This adds the "test_compression" command when building the sandbox. This
tests the existing compression and decompression routines for simple
sanity and for buffer overflow conditions.
Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 30 Aug 2013 17:00:09 +0000 (11:00 -0600)]
sandbox: Correct compiler warnings in cmd_bootm/cmd_ximg
Correct the following warnings found with sandbox when compression
is enabled.
cmd_bootm.c: In function 'bootm_load_os':
cmd_bootm.c:443:11: warning: passing argument 4 of 'lzop_decompress' from incompatible pointer type [enabled by default]
/usr/local/google/c/cosarm/src/third_party/u-boot/files/include/linux/lzo.h:31:5: note: expected 'size_t *' but argument is of type 'uint *'
cmd_ximg.c: In function 'do_imgextract':
cmd_ximg.c:225:6: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
cmd_ximg.c:225:14: warning: 'hdr' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Kees Cook <keescook@chromium.org>
Some _CLKGATE_MASK and _FRAC_MASK macros were wrong for PFD_480
and the PFD_528 macros were missing.
Fortunately, the incorrect macros weren't being used.
Since both the PFD_480 and PFD_528 registers have the same
structure, and the fields are identical for [0..3] in bytes
[0..3], so a single set of macros will suffice.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
projects / u-boot / log