Kumar Gala [Wed, 26 Mar 2008 13:34:25 +0000 (08:34 -0500)]
85xx: Update multicore boot mechanism to ePAPR v0.81 spec
The following changes are needed to be inline with ePAPR v0.81:
* r4, r5 and now always set to 0 on boot release
* r7 is used to pass the size of the initial map area (IMA)
* EPAPR_MAGIC value changed for book-e processors
* changes in the spin table layout
* spin table supports a 64-bit physical release address
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Jon Loeliger [Wed, 19 Mar 2008 20:02:07 +0000 (15:02 -0500)]
FSL: Clean up board/freescale/common/Makefile
Each file that can be built here now follows some
CONFIG_ option so that they are appropriately built
or not, as needed. And CONFIG_ defines were added
to various board config files to make sure that happens.
The other board/freescale/*/Makefiles no longer need
to reach up and over into ../common to build their
individually needed files any more.
Boards that are CDS specific were renamed with cds_ prefix.
James Yang [Tue, 12 Feb 2008 22:35:07 +0000 (16:35 -0600)]
85xx: Expand CCSR space with more DDR controller registers.
Signed-off-by: James Yang <James.Yang@freescale.com> Signed-off-by: Jon Loeliger <jdl@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
James Yang [Sat, 9 Feb 2008 00:05:08 +0000 (18:05 -0600)]
85xx: Speed up get_ddr_freq() and get_bus_freq()
get_ddr_freq() and get_bus_freq() used get_sys_info() each time they were
called. However, get_sys_info() recalculates extraneous information when
called each time. Have get_ddr_freq() and get_bus_freq() return memoized
values from global_data instead.
Signed-off-by: James Yang <James.Yang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
James Yang [Fri, 8 Feb 2008 22:44:53 +0000 (16:44 -0600)]
85xx: get_tbclk() speed up and rounding fix
Speed up get_tbclk() by referencing pre-computed bus clock
frequency value from global data instead of sys_info_t. Fix
rounding of result to nearest; previously it was rounding
upwards.
Signed-off-by: James Yang <James.Yang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Andy Fleming [Wed, 6 Feb 2008 07:19:40 +0000 (01:19 -0600)]
Update SVR numbers to expand support
FSL has taken to using SVR[16:23] as an SOC sub-version field. This
is used to distinguish certain variants within an SOC family. To
account for this, we add the SVR_SOC_VER() macro, and update the SVR_*
constants to reflect the larger value. We also add SVR numbers for all
of the current variants. Finally, to make things neater, rather than
use an enormous switch statement to print out the CPU type, we create
and array of SVR/name pairs (using a macro), and print out the CPU name
that matches the SVR SOC version.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Anton Vorontsov [Fri, 14 Mar 2008 20:20:18 +0000 (23:20 +0300)]
83xx/fdt_support: let user specifiy FSL USB Dual-Role controller role
Linux understands "host" (default), "peripheral" and "otg" (broken).
Though, U-Boot doesn't restrict dr_mode variable to these values (think
of renames in future).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Joe D'Abbraccio [Mon, 24 Mar 2008 17:00:59 +0000 (13:00 -0400)]
Modified the DDR SDRAM clock control register to delay MCK/MCK_B 3/4 clock
With the original value of 1/2 clock cycle delay, the system ran relatively
stable except when we run benchmarks that are intensive users of memory.
When I run samba connected disk with a HDBENCH test, the system locks-up
or reboots sporadically.
Signed-off by: Joe D'Abbraccio <Joe.D'abbraccio@freescale.com>
The following changes are based on kernel UCC ethernet performance:
1. Make the CSB bus pipeline depth as 4, and enable the repeat mode
2. Optimize transactions between QE and CSB. Added CFG_SPCR_OPT
switch to enable this setting.
The following changes are based on the App Note AN3369 and
verified to improve memory latency using LMbench:
3. CS0_CONFIG[AP_n_EN] is changed from 1 to 0
4. CS0_CONFIG[ODT_WR_CONFIG] set to 1. Was a reserved setting
previously.
5. TIMING_CFG_1[WRREC] is changed from 3clks to 2clks (based on
Twr=15ns, and this was already the setting in DDR_MODE)
6. TIMING_CFG_1[PRETOACT] is changed from 3clks to 2clks. (based on
Trp=15ns)
7. TIMING_CFG_1[ACTTOPRE] is changed from 9clks to 6clks. (based on
Tras=40ns)
8. TIMING_CFG_1[ACTTORW] is changed from 3clks to 2clks. (based on
Trcd=15ns)
9. TIMING_CFG_1[REFREC] changed from 21 clks to 11clks. (based on
Trfc=75ns)
10. TIMING_CFG_2[FOUR_ACT] is changed from 10 clks to 7clks. (based
on Tfaw=50ns)
11. TIMING_CFG_2[ADD_LAT] and DDR_MODE[AL] changed from 0 to 1 (based
on CL=3 and WL=2).
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com> Acked-by: Kim Phillips <kim.phillips@freescale.com>
Timur Tabi [Fri, 8 Feb 2008 19:15:55 +0000 (13:15 -0600)]
83xx: Add Vitesse VSC7385 firmware uploading
Update the MPC8349E-mITX, MPC8313E-RDB, and MPC837XE-RDB board files to upload
the Vitesse VSC7385 firmware. Changed CONFIG_VSC7385 to CONFIG_VSC7385_ENET.
Cleaned up the board header files to make selecting the VSC7385 easier to
control.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Timur Tabi [Fri, 8 Feb 2008 19:15:54 +0000 (13:15 -0600)]
NET: Add Vitesse VSC7385 firmware uploading
The Vitesse VSC7385 is a 5-port switch found on the Freescale MPC8349E-mITX
and other boards. A small firwmare must be uploaded to its on-board memory
before it can be enabled. This patch adds the code which uploads firmware
(but not the firmware itself).
Previously, this feature was provided by a U-Boot application that was
made available only on Freescale BSPs. The VSC7385 firmware must still
be obtained separately, but at least there is no longer a need for a separate
application.
Signed-off-by: Timur Tabi <timur@freescale.com> Acked-by: Ben Warren <biggerbadderben@gmail.com>
Jerry Van Baren [Sat, 22 Mar 2008 18:23:49 +0000 (14:23 -0400)]
Remove deprecated CONFIG_OF_HAS_UBOOT_ENV and CONFIG_OF_HAS_BD_T
These defines embedded the u-boot env variables and/or the bd_t structure
in the fdt blob. The conclusion of discussion on the u-boot email list
was that embedding these in the fdt blob is not useful: there are better
ways of passing the data (in fact, the fdt blob itself replaces the
bd_t struct).
The only board that enables these is the stxxtc and they don't appear
to be used by linux.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com> Acked-by: Kim Phillips <kim.phillips@freescale.com>
Kyungmin Park [Sun, 16 Mar 2008 23:54:06 +0000 (08:54 +0900)]
Add Flex-OneNAND booting support
Flex-OneNAND is a monolithic integrated circuit with a NAND Flash array
using a NOR Flash interface. This on-chip integration enables system designers
to reduce external system logic and use high-density NAND Flash
in applications that would otherwise have to use more NOR components.
Flex-OneNAND enables users to configure to partition it into SLC and MLC areas
in more flexible way. While MLC area of Flex-OneNAND can be used to store data
that require low reliability and high density, SLC area of Flex-OneNAND
to store data that need high reliability and high performance. Flex-OneNAND
can let users take advantage of storing these two different types of data
into one chip, which is making Flex-OneNAND more cost- and space-effective.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
goda.yusuke [Wed, 5 Mar 2008 08:08:20 +0000 (17:08 +0900)]
net: Divided code of NE2000 ethernet driver
There are more devices of the NE2000 base.
A present code is difficult for us to support more devices.
To support more NE2000 clone devices, separated the function.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com> Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Mike Frysinger [Mon, 25 Feb 2008 04:58:13 +0000 (23:58 -0500)]
net/Blackfin: move on-chip MAC driver into drivers/net/
The Blackfin on-chip MAC driver was being managed in the BF537-STAMP board
directory, but it is not board specific, so relocate it to the drivers dir
so that other Blackfin ports can utilize it.
Mike Frysinger [Mon, 25 Feb 2008 04:52:35 +0000 (23:52 -0500)]
smc91111: use SSYNC() rather than asm(ssync) for Blackfin
Since the "ssync" instruction may have hardware anomalies associated with
it, have the smc91111 driver use the SSYNC macro rather than invoking it
directly. We workaround all the anomalies via this macro.
Kumar Gala [Fri, 15 Feb 2008 21:16:18 +0000 (15:16 -0600)]
ppc: Allow boards to specify how much memory they can map
For historical reasons we limited the stack to 256M because some boards
could only map that much via BATS. However newer boards are capable of
mapping more memory (for example 85xx is capble of doing up to 2G).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 15 Feb 2008 02:44:42 +0000 (20:44 -0600)]
Add setexpr command
Add a simple expr style command that will set an env variable as the result
of the command. This allows us to do simple math in shell. The following
operations are supported: &, |, ^, +, -, *, /.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add setup_c0_status from Linux. For the moment we disable interrupts, set
CU0, mark the kernel mode, and clear ERL and EXL. This is good enough for
reset-time configuration and will work well across most processors.
We do Hit_Writeback_Inv_D and Hit_Invalidate_I. You might think that you
don't need to do Hit_Invalidate_I, but flush_cache() needs it since this
function is used not only in U-Boot specfic programs but also at loading
target binaries.
Currently we do 1) Index_Store_Tag_I, 2) Fill and 3) Index_Store_Tag_I
again per a loop for I-cache initialization. But according to 'See MIPS
Run', we're encouraged to use three separate loops rather than combining
them *for both I- and D-cache*. This patch tries to fix this.
In accordance with fixing above, mips_init_[id]cache are separated from
mips_cache_reset(), and rewrite cache loops are completely rewritten with
useful macros.
This patch replaces the current function definitions with NESTED, LEAF
and END macro. They specify some more additional information about the
function; an alignment of symbol, type of symbol, stack frame usage, etc.
These information explicitly tells the assembler and the debugger about
the types of code we want to generate.
[MIPS] Request for the 'mips_cache_lock()' removal
The initial intension of having mips_cache_lock() was to use the cache
as memory for temporary stack use so that a C environment can be set up
as early as possible.
But now mips_cache_lock() follow lowlevel_init(). We've already have the
real memory initilaized at this point, therefore we could/should use it.
No reason to lock at all.
Other problems:
Cache locking is not consistent across MIPS implementaions. Some imple-
mentations don't support locking at all. The style of locking varies -
some support per line locking, others per way, etc. Some parts use bits
in status registers instead of cache ops. Current mips_cache_lock() is
not necessarily general-purpose.
And this is worthy of special mention; once U-Boot/MIPS locks the lines,
they are never get unlocked, so the code relies on whatever gets loaded
after U-Boot to re-initialize the cache and clear the locks. We're sup-
posed to have CFG_INIT_RAM_LOCK and unlock_ram_in_cache() implemented,
but leave the situation as it is for a long time.
For these reasons, I proposed the removal of mips_cache_lock() from the
global start-up code.
This patch adds CFG_INIT_RAM_LOCK_MIPS to make existing users aware that
*things have changed*. If he wants the same behavior as before, he needs
to have CFG_INIT_RAM_LOCK_MIPS in his config file.
If we don't have any regression report through several releases, then
we'll remove codes entirely.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp> Acked-by: Andrew Dyer <amdyer@gmail.com>
Yuri Tikhonov [Mon, 24 Mar 2008 10:30:54 +0000 (11:30 +0100)]
lwmon5 SYSMON POST: fix backlight control
If the LWMON5 config has SYSMON POST among CONFIG_POSTs which may be
run on the board, then the SYSMON POST controls the display backlight
(doesn't switch backlight ON if POST FAILED, and does switch the
backlight ON if PASSED).
If not, then the video driver controls the display backlight (just
switch ON the backlight upon initialization).
In current source code, when the device number of PCI is 0, process PCI
bridge without fail. However, when the device number is 0, it is not PCI
always bridge. There are times when device of PCI allocates.
When CONFIG_PCI_SKIP_HOST_BRIDGE is enable, this problem is solved when
use this patch.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Acked-by: Stefan Roese <sr@denx.de>
Bartlomiej Sieka [Thu, 20 Mar 2008 22:23:13 +0000 (23:23 +0100)]
[new uImage] Do not compile new uImage format support by default
Disable default building of new uImage format support in preparation
for merge with the master. Support for new format can be enabled on
a per-board basis, by defining the following in the board's config file:
#define CONFIG_FIT 1
#define CONFIG_OF_LIBFDT 1
This can be optionally defined to give more verbose output:
Bartlomiej Sieka [Thu, 20 Mar 2008 18:38:45 +0000 (19:38 +0100)]
[new uImage] Compilation and new uImage handling fixes for imxtract
Fix imxtract command not being compiled-in despite CONFIG_CMD_XIMG being in
include/config_cmd_default.h. Fix few warnings and handling of new format
images.
Yuri Tikhonov [Thu, 20 Mar 2008 14:56:04 +0000 (17:56 +0300)]
LWMON5: POST RTC fix
Modify the RTC API to provide one a status for the time reported by
the rtc_get() function:
0 - a reliable time is guaranteed,
< 0 - a reliable time isn't guaranteed (power fault, clock issues,
and so on).
The RTC chip drivers are responsible for providing this info if the
corresponding chip supports such functionality. If not - always
report that the time is reliable.
The POST RTC test was modified to detect the RTC faults utilizing
this new rtc_get() feature.
Stefan Roese [Wed, 19 Mar 2008 06:09:26 +0000 (07:09 +0100)]
CFI: Small cleanup for FLASH_SHOW_PROGRESS
With this patch we don't need that many #ifdef's in the code. It moves
the subtraction into the macro and defines a NOP-macro when
CONFIG_FLASH_SHOW_PROGRESS is not defined.
Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Gerald Van Baren <vanbaren@cideas.com>
projects / u-boot / log