Jonathan Gray [Fri, 6 Apr 2018 08:45:49 +0000 (18:45 +1000)]
rpi: Complete table of models with new revision code scheme
In the model table for the new revision code encoding documented in
https://www.raspberrypi.org/documentation/hardware/raspberrypi/revision-codes/README.md
add the entries for old models with the new scheme and add CM3 which
only appears in the new scheme.
A device tree for CM3 is not currently upstreamed in linux. When that
happens the name will likely have to be adjusted in the table.
Signed-off-by: Jonathan Gray <jsg@jsg.id.au> Signed-off-by: Alexander Graf <agraf@suse.de>
According to Phil Elwell in
https://github.com/raspberrypi/firmware/issues/953
the SDHost controller shares the core/VPU clock and doesn't use
the EMMC clock.
Use the core clock id when determining the frequency to allow
U-Boot to work with recent versions of raspberrypi-firmware.
Otherwise U-Boot hangs at:
U-Boot 2018.03 (Mar 14 2018 - 20:36:00 +1100)
DRAM: 948 MiB
RPI 3 Model B (0xa02082)
MMC: mmc@7e202000: 0, sdhci@7e300000: 1
Loading Environment from FAT...
Signed-off-by: Jonathan Gray <jsg@jsg.id.au> Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Thu, 15 Mar 2018 14:05:37 +0000 (15:05 +0100)]
rpi: Add identifier for the new RPi3 B+
The Raspberr Pi Foundation released a new RPi3 version which we want
to detect as well, so we can enable ethernet on it and know the correct
device tree file name.
Alexander Graf [Thu, 5 Apr 2018 09:36:22 +0000 (11:36 +0200)]
rpi: Allow to boot without serial
When we enable CONFIG_OF_BOARD on Raspberry Pis, we may end up without
serial console support in early boot. Hence we need to make the serial
port optional, otherwise we will never get to the point where serial
would be probed.
Mario Six [Mon, 12 Mar 2018 13:53:33 +0000 (14:53 +0100)]
core: ofnode: Fix translation for #size-cells == 0
Commit 286ede6 ("drivers: core: Add translation in live tree case") made
dev_get_addr always use proper bus translations for addresses read from
the device tree. But this leads to problems with certain busses, e.g.
I2C busses, which run into an error during translation, and hence stop
working.
It turns out that of_translate_address() and fdt_translate_address()
stop the address translation with an error when they're asked to
translate addresses for busses where #size-cells == 0 (comment from
drivers/core/of_addr.c):
* Note: We consider that crossing any level with #size-cells == 0 to mean
* that translation is impossible (that is we are not dealing with a value
* that can be mapped to a cpu physical address). This is not really specified
* that way, but this is traditionally the way IBM at least do things
To fix this case, we check in both the live-tree and non-live tree-case,
whether the bus of the device whose address is about to be translated
has size-cell size zero. If this is the case, we just read the address
as a plain integer and return it, and only apply bus translations if the
size-cell size if greater than zero.
Signed-off-by: Mario Six <mario.six@gdsys.cc> Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com> Reported-by: Martin Fuzzey <mfuzzey@parkeon.com> Fixes: 286ede6 ("drivers: core: Add translation in live tree case") Reviewed-by: Simon Glass <sjg@chromium.org>
Wilson Ding [Mon, 26 Mar 2018 07:57:31 +0000 (15:57 +0800)]
arm64: a37xx: dts: enable pcie port
This patch enabled PCIe port on both devel-board
and espressobin board.
Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Wilson Ding <dingwei@marvell.com> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wilson Ding <dingwei@marvell.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Wilson Ding [Mon, 26 Mar 2018 07:57:29 +0000 (15:57 +0800)]
arm64: a37xx: pci: add support for aardvark pcie driver
This patch introduced the Aardvark PCIe driver based
driver model.
The PCIe driver is supposed to work in Root Complex
mode. It only supports X1 lane width.
Signed-off-by: Wilson Ding <dingwei@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/38725 Reviewed-by: Victor Gu <xigu@marvell.com> Reviewed-by: Hua Jing <jinghua@marvell.com> Tested-by: Hua Jing <jinghua@marvell.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Wilson Ding [Mon, 26 Mar 2018 07:57:28 +0000 (15:57 +0800)]
arm64: a37xx: populate pcie memory region
This patch added a new region of 32MiB AT 0xe800.0000
to Armada37x0's memory map. This region is supposed to
be mapped in MMU in order to enable the access to the
PCI I/O or MEM resources.
Signed-off-by: Wilson Ding <dingwei@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/38724 Tested-by: iSoC Platform CI <ykjenk@marvell.com> Reviewed-by: Victor Gu <xigu@marvell.com> Signed-off-by: Ken Ma <make@marvell.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Ken Ma [Mon, 26 Mar 2018 07:56:05 +0000 (15:56 +0800)]
doc: a37xx: Introduce pinctrl device tree binding
Reviewed-on: http://vgitil04.il.marvell.com:8080/43289 Tested-by: iSoC Platform CI <ykjenk@marvell.com> Reviewed-by: Kostya Porotchkin <kostap@marvell.com> Reviewed-by: Igal Liberman <igall@marvell.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Ken Ma [Mon, 26 Mar 2018 07:56:04 +0000 (15:56 +0800)]
arm64: a37xx: dts: Correct mpp definitions
This patch corrects below mpp definitions for armada 3720 DB board
and ESPRESSOBin board:
- "smi" pins group is added and "smi" function is set for eth0;
- Now pcie pins are used as gpio to implement PCIe function in
hardware, so "pcie" group function is changed to "gpio".
Reviewed-on: http://vgitil04.il.marvell.com:8080/43287 Reviewed-by: Hua Jing <jinghua@marvell.com> Tested-by: iSoC Platform CI <ykjenk@marvell.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Ken Ma [Mon, 26 Mar 2018 07:56:03 +0000 (15:56 +0800)]
arm64: a37xx: pinctrl: Correct mpp definitions
This patch corrects below mpp definitions:
- The sdio_sb group is composed of 6 pins and not 5;
- The rgmii group contains pins mpp2[17:6] and not mpp2[19:6];
- Pin of group "pmic0" is mpp1[6] but not mpp1[16];
- Pin of group "pmic1" is mpp1[7] but not mpp1[17];
- A new group "smi" is added in A0 with 2 pins - mpp2[19:18], its
bitmask is bit4;
- Group "pcie1" has 3 pins in A0 - mpp2[5:3], its bit mask is
bit5 | bit9 | bit10 but not bit4;
- Group "ptp" has 3 pins in A0 as Z1, but its bitmask is changed to
bit11 | bit12 | bit13.
Reviewed-on: http://vgitil04.il.marvell.com:8080/43288 Tested-by: iSoC Platform CI <ykjenk@marvell.com> Reviewed-by: Hua Jing <jinghua@marvell.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Ken Ma [Mon, 26 Mar 2018 07:56:02 +0000 (15:56 +0800)]
arm64: a37xx: pinctrl: Fix gpio pin offset in register
For armada_37xx_update_reg(), the parameter offset should be pointer so
that it can be updated, otherwise offset will keep old value, and then
when offset is larger than or equal to 32 the mask calculated by
"BIT(offset)" will be 0 in gpio chip hook functions, it's an error,
this patch set offset parameter of armada_37xx_update_reg() as pointer.
Reviewed-on: http://vgitil04.il.marvell.com:8080/43287 Reviewed-by: Hua Jing <jinghua@marvell.com> Tested-by: iSoC Platform CI <ykjenk@marvell.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Ken Ma [Mon, 26 Mar 2018 07:56:01 +0000 (15:56 +0800)]
arm64: a37xx: pinctrl: Fix the pin 23 on south bridge
Pin 23 on South bridge does not belong to the rgmii group. It belongs to
a separate group which can have 3 functions.
Due to this the fix also have to update the way the functions are
managed. Until now each groups used NB_FUNCS(which was 2) functions. For
the mpp23, 3 functions are available but it is the only group which needs
it, so on the loop involving NB_FUNCS an extra test was added to handle
only the functions added.
The bug was visible when the gpio regulator used the gpio 23, the whole
rgmii group was setup to gpio which broke the Ethernet support on the
Armada 3720 DB board. Thanks to this patch, the UHS SD cards (which need
the vqmmc) _and_ the Ethernet work again.
Reviewed-on: http://vgitil04.il.marvell.com:8080/43284 Reviewed-by: Hua Jing <jinghua@marvell.com> Tested-by: iSoC Platform CI <ykjenk@marvell.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Ken Ma [Mon, 26 Mar 2018 07:56:00 +0000 (15:56 +0800)]
arm64: a37xx: dts: Fix the number of GPIO on south bridge
The number of pins in South Bridge is 30 and not 29. There is a fix for
the driver for the pinctrl, but a fix is also need at device tree level
for the GPIO.
Reviewed-on: http://vgitil04.il.marvell.com:8080/43286 Reviewed-by: Hua Jing <jinghua@marvell.com> Tested-by: iSoC Platform CI <ykjenk@marvell.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Ken Ma [Mon, 26 Mar 2018 07:55:59 +0000 (15:55 +0800)]
arm64: a37xx: pinctrl: Fix number of pin in south bridge
On the south bridge we have pin from 0 to 29, so it gives 30 pins (and
not 29).
Reviewed-on: http://vgitil04.il.marvell.com:8080/43285 Tested-by: iSoC Platform CI <ykjenk@marvell.com> Reviewed-by: Hua Jing <jinghua@marvell.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Add mmc pins, pcie pins and sdio pins definition and do these pins'
configuration for DB board and espressobin board;
Add uart2 pins configuration for DB board.
Reviewed-on: http://vgitil04.il.marvell.com:8080/40914 Reviewed-by: Wilson Ding <dingwei@marvell.com> Tested-by: Wilson Ding <dingwei@marvell.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Ken Ma [Mon, 26 Mar 2018 07:55:57 +0000 (15:55 +0800)]
arm64: a37xx: dts: Add pinctrl configuration for ESPRESSOBin board
Reviewed-on: http://vgitil04.il.marvell.com:8080/40913 Reviewed-by: Wilson Ding <dingwei@marvell.com> Tested-by: Wilson Ding <dingwei@marvell.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Ken Ma [Mon, 26 Mar 2018 07:55:56 +0000 (15:55 +0800)]
arm64: a37xx: defconfig: Enable PINCTRL and GPIO support for ESPRESSOBin board
This patch enable the PINCTRL and GPIO support, including the GPIO
command on the Armada 3720 espressobin board.
Reviewed-on: http://vgitil04.il.marvell.com:8080/40746 Tested-by: iSoC Platform CI <ykjenk@marvell.com> Reviewed-by: Wilson Ding <dingwei@marvell.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Ken Ma <make@marvell.com> Signed-off-by: Stefan Roese <sr@denx.de>
Mark Kettenis [Sat, 17 Mar 2018 08:34:27 +0000 (09:34 +0100)]
arm64: mvebu: a8k: Add distro boot support
The various load address values are taken from the a37xx configuration
and match the dowstream 'u-boot-2017.03-armada-17.10' release where
appropriate.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Signed-off-by: Stefan Roese <sr@denx.de>
Alexander Graf [Thu, 15 Mar 2018 10:14:19 +0000 (11:14 +0100)]
kwbimage: Fix out of bounds access
The kwbimage format is reading beyond its header structure if it
misdetects a Xilinx Zynq image and tries to read it. Fix it by
sanity checking that the header we want to read fits inside our
file size.
Signed-off-by: Alexander Graf <agraf@suse.de> Tested-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Ivan Gorinov [Tue, 27 Mar 2018 01:06:54 +0000 (18:06 -0700)]
x86: zImage: Pass working device tree data to the kernel
On x86 platforms, U-Boot does not pass Device Tree data to the kernel.
This prevents the kernel from using FDT loaded by U-Boot.
Read the working FDT address from the "fdtaddr" environment variable
and add a copy of the FDT data to the kernel setup_data list.
Signed-off-by: Ivan Gorinov <ivan.gorinov@intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: add #include <linux/libfdt.h> to zimage.c to fix build error] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Use dm_pci_map_bar function for BAR mapping. This has the advantage
of clearing BAR flags and and only accepting mapped memory.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com> Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Bin Meng [Tue, 27 Mar 2018 07:46:05 +0000 (00:46 -0700)]
dm: pci: Check board information pointer in decode_regions()
PCI enumeration may happen very early on an x86 board. The board
information pointer should have been checked in decode_regions()
as its space may not be allocated yet.
With this commit, Intel Galileo board boots again.
Fixes: 664758c ("pci: Fix decode regions for memory banks") Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Alexander Graf [Mon, 4 Dec 2017 15:33:26 +0000 (16:33 +0100)]
efi_stub: Fix GDT_NOTSYS check
The get_codeseg32() wants to know if a passed in descriptor has
flag GDT_NOTSYS set (desc & GDT_NOTSYS), not whether desc and
GDT_NOTSYS are not != 0 (desk && GDT_NOTSYS).
This is an obvious typo. Fix it up.
Signed-off-by: Alexander Graf <agraf@suse.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Rick Chen [Thu, 29 Mar 2018 02:08:33 +0000 (10:08 +0800)]
riscv: ae250: Support DT provided by the board at runtime
Enable CONFIG_OF_BOAD to support delivery dtb to u-boot
at run time instead of embedded.
There are two methods to delivery dtb.
1 Pass from loader:
When u-boot boot from RAM, gdb or loader can pass dtb
via a2 to u-boot dynamically. Of course gdb or loader
shall be in charge of dtb delivery.
2 Configure CONFIG_SYS_FDT_BASE:
It can be configured as RAM or ROM base statically,
no mater u-boot boot from RAM or ROM.
If it was configured as ROM base, dtb can be burned
into ROM(spi flash) by spi driver.
Meanwhile remove CONFIG_SKIP_LOWLEVEL_INIT which is
useless in nx25-ae250 configuration.
Signed-off-by: Rick Chen <rick@andestech.com> Signed-off-by: Rick Chen <rickchen36@gmail.com> Cc: Greentime Hu <green.hu@gmail.com>
Rick Chen [Tue, 20 Mar 2018 06:30:52 +0000 (14:30 +0800)]
mmc: ftsdc010: Drop non-dm code
Only three defconfig(adp-ag101p_defconfig,
adp-ae3xx_defconfig, nx25-ae250_defconfig)
set CONFIG_FTSDC010=y. And they all also
enable CONFIG_DM_MMC. So the non-dm code
of ftsdc010 can be dropped now.
Signed-off-by: Rick Chen <rick@andestech.com> Signed-off-by: Rick Chen <rickchen36@gmail.com> Cc: Greentime Hu <green.hu@gmail.com>
Rick Chen [Mon, 25 Dec 2017 08:25:26 +0000 (16:25 +0800)]
mmc: ftsdc010: Support High-Speed mode
ftsdc010 dm driver has been disable High-Speed mode
as default to work around Andes AE3XX platform's problem,
because of it does not support High-Speed mode in
commit id 73cd56b2df213c629191139e5c6705e069b6214f.
But other platforms or SoCs maybe support this function.
So High-Speed mode can be enabled from dts with
cap-mmc-highspeed or cap-sd-highspeed property.
Signed-off-by: Rick Chen <rick@andestech.com> Signed-off-by: Rick Chen <rickchen36@gmail.com>
Philipp Tomsich [Mon, 26 Mar 2018 17:59:10 +0000 (19:59 +0200)]
rockchip: sdhci: support 8bit bus-width
The Rockchip-specific SDHCI wrapper does not process the 'bus-width'
property in the SDHCI node. Consequently, the bus is always kept in
4bit mode, even if 8bit wide operation is available, supported and
requested in the DTS.
This change adds processing of the 'bus-width' property and sets the
host capability flag for an 8bit wide bus, if set to 8. As the logic
in sdhci.c does not support clearing the 4bit capability, we assume
that 4bit operation is always supported.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Mon, 26 Mar 2018 17:59:09 +0000 (19:59 +0200)]
rockchip: mmc: update MAINTAINERS
The Rockchip-specific wrappers to the DW-MMC and the SDHCI driver
were not covered as part of what's maintained by the architecture
maintainers. Add them here.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Mon, 26 Mar 2018 17:59:08 +0000 (19:59 +0200)]
rockchip: defconfig: puma-rk3399: enable DMA for SDHCI controller
For the RK3399-Q7, we have a fast eMMC connected in an 8 bit wide
configuration to the SDHCI controller (sdhci@fe330000). Enable DMA
within the SDHCI driver to get the best performance out of it.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Mark Kettenis [Sat, 17 Mar 2018 08:48:25 +0000 (09:48 +0100)]
rockchip: rk3399: set fdtfile
Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
rockchip: clk: rk3188: update dpll settings to make EMAC work
The patch set dpll settings for 300MHz to values used by binary
blob[1]. With new values dpll still generate 300MHz clock, but
EMAC work. Probably with new values dpll generate more stable clock.
dpll on rk3188 provide clocks to DDR and EMAC. With current
dpll settings EMAC doesn't work on radxa rock. EMAC sends packets
to network, but it doesn't receive anything. ifconfig shows a lot
of framing errors.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
video: rk3288_mipi: check in rk_mipi_ofdata_to_platdata
The error checking should also catch the case that no range has beeen
defined.
syscon_get_first_range() returns NULL if no range is defined.
cf. rk3399_mipi.c
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Pointers are never negative. Use macro IS_ERR() for checking.
cf. rk3288_mipi.c
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Assigning f_rkusb->reboot_flag twice doesn't make sense.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
If we want to check the duration we need to increment the counter.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
rockchip: pinctrl: rk3188: Move the iomux definitions into pinctrl-driver
Clean the iomux definitions at grf_rk3188.h, and move them into
pinctrl-driver for resolving the compiling error of redefinition.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
rockchip: pinctrl: rk3036: Move the iomux definitions into pinctrl-driver
Clean the iomux definitions at grf_rk3036.h, and move them into
pinctrl-driver for resolving the compiling error of redefinition.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Mon, 12 Mar 2018 13:56:42 +0000 (14:56 +0100)]
rockchip: pinctrl: rk3399: add support for I2C[123467]
This adds support for the (to date unsupported) I2C controllers 1~4
and 6~7 (i.e. now all controllers except I2C5, which is not accessible
on the RK3399-Q7, are supported by pinctrl).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tom Rini [Sun, 25 Mar 2018 16:00:00 +0000 (12:00 -0400)]
Merge tag 'xilinx-for-v2018.05' of git://git.denx.de/u-boot-microblaze
Xilinx changes for v2018.05
- Fix mkimage recognition
- Update all my fragments
ZynqMP:
- Use clk driver
- Support loading elfs in el1
- Various DTS and defconfig changes
- Enable newer pmufw versions
- Support more clocks
- Remove ep108
- Secure image support
- Fix memtest setup
Zynq:
- Enabling watchdog driver
- Support more clocks
- defconfig changes
Petr Vorel [Sat, 24 Mar 2018 00:49:23 +0000 (01:49 +0100)]
Convert CONFIG_UBIFS_SILENCE_MSG to Kconfig
Introduce another difference from upstream (kernel) source in
fs/ubifs/super.c: adding preprocessor condition as y variable in
mount_ubifs() depends on CONFIG_UBIFS_SILENCE_MSG:
fs/ubifs/super.c:1337:15: error: variable ?y? set but not used [-Werror=unused-but-set-variable]
long long x, y;
Not setting CONFIG_UBIFS_SILENCE_MSG in am335x_igep003x_defconfig and
igep0032_defconfig. Although it was defined in their config headers, it
depends on CMD_UBIFS which is not set for them.
Signed-off-by: Petr Vorel <petr.vorel@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Heiko Schocher <hs@denx.de>
The ti,pindir-d0-out-d1-in property is not expected to have a value
according to the device-tree binding, so treat it as a boolean not a
uint property.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Reviewed-by: Jagan Teki <jagan@openedev.com>
Tom Rini [Fri, 23 Mar 2018 13:31:24 +0000 (09:31 -0400)]
Merge git://git.denx.de/u-boot-arc
Alexey:
1. Significantly rework cache-related functionality.
In particular that fixes coherency problems in some corner-cases,
allows us to enable and disable caches in run-time and still
have properly running system, finally support execution from
real flash (before we used to run from DDR from the very beginning).
2. Remove string routines implemented in assembly.
That allows us to build and run U-Boot on wide range of ARC cores
with different configurations. I.e. whatever tuning is used on GCC's
command-line we'll get code for desired flavor of ARC.
Otherwise for each and every corner-case we would need to add ifdefs
in assembly code to accommodate missing instructions etc.
3. Get use of GCC's garbage collector which helps to slim-down resulting image
quite a bit.
4. Also now we may disable U-Boot self-relocation for ARC if needed either
by platform or for debugging purposes.
Michal Simek [Tue, 13 Mar 2018 10:07:25 +0000 (11:07 +0100)]
MAINTAINERS: Fix Zynq/ZynqMP and Microblaze fragments
Fix my fragments to list all files in the repo.
Also fix path to for Xilinx Zynq SoC (mach-zynq)
It should be the part of
"ARM: zynq: move SoC sources to mach-zynq"
(sha1: 0107f2403669f764ab726d0d404e35bb9447bbcc)
And cover dts files in board MAINTAINERS files.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 14 Mar 2018 10:02:24 +0000 (11:02 +0100)]
tools: xilinx: Fix zynq/zynqmp image recognition
There is an issue to recognize zynq or zynqmp image because header
checking is just the same. That's why zynqmp images are recognized as
zynq one.
Check unused fields which are initialized to zero in zynq format
(__reserved1 0x38 and __reserved2 0x44) which are initialized for
zynqmp. This should ensure that images are properly recognized by:
./tools/mkimage -l spl/boot.bin
Also show image type as ZynqMP instead of Zynq which is confusing.
Reported-by: Alexander Graf <agraf@suse.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Tested-by: Alexander Graf <agraf@suse.de>
arm64: zynqmp: Add support for verifying secure images
This patch adds new command "zynqmp" to handle zynqmp
specific commands like "zynqmp secure". This secure command is
used for verifying zynqmp specific secure images. The secure
image can either be authenticated or encrypted or both encrypted
and authenticated. The secure image is prepared using bootgen
and will be in xilinx specific BOOT.BIN format. The optional
key can be used for decryption of encrypted image if user
key was specified while creation BOOT.BIN.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The vcu disable bit in efuse ipdisable register is valid only
if PL powered up so, consider PL powerup status for determing
EG/EV part. If PL is not powered up, ignore EG/EV part of string.
The PL powerup status will be filled by pmufw based on PL PROGB
status in the 9th bit of version field.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Vipul Kumar [Mon, 5 Mar 2018 09:54:59 +0000 (15:24 +0530)]
arm64: zynqmp: nand: Fixed NAND erase issue for size 1GiB or more
NAND erase was not happening for size 1GiB or more. Erase
command was executing successfully but in actual, it was not
erasing.
This patch fixed erase issue for 1 GiB or more size nand.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
projects / u-boot / log