Vignesh R [Sat, 5 Nov 2016 10:35:16 +0000 (16:05 +0530)]
spi: ti_qspi: Fix baudrate divider calculation
Fix the divider calculation logic to choose a value so that the
resulting baudrate is either equal to or closest possible baudrate less
than the requested value. While at that, cleanup ti_spi_set_speed().
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
Vignesh R [Sat, 5 Nov 2016 10:35:15 +0000 (16:05 +0530)]
ARM: dts: dra7xx: Update spi-max-frequency for qspi slave node
Update the spi-max-frequency property of m25p80 flash slave to match
that of TI QSPI controller node, so that QSPI operations happen at
maximum supported frequency of 76.8MHz.
Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
Lokesh Vutla [Thu, 3 Nov 2016 10:05:02 +0000 (15:35 +0530)]
ARM: k2g: Update PLL Multiplier and divider values
Only a certain set of PLLM/D values are recommended to configure the DDR
at the required speeds for a given clock input frequency. Updating these
values as specified in Data Sheet[1] Table 5-18
[1] http://www.ti.com/lit/ds/symlink/66ak2g02.pdf
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Keerthy [Sat, 29 Oct 2016 09:49:10 +0000 (15:19 +0530)]
arm: Set TTB XN bit in case DCACHE_OFF for LPAE mode
While we setup the mmu initially we mark set_section_dcache with
DCACHE_OFF flag. In case of non-LPAE mode the DCACHE_OFF macro
is rightly defined with TTB_SECT_XN_MASK set so as to mark all the
4GB XN. In case of LPAE mode XN(Execute-never) bit is not set with
DCACHE_OFF. Hence XN bit is not set by default for DCACHE_OFF which
keeps all the regions execute okay and this leads to random speculative
fetches in random memory regions which was eventually caught by kernel
omap-l3-noc driver.
Fix this to mark the regions as XN by default.
Signed-off-by: Keerthy <j-keerthy@ti.com> Reviewed-by: Alexander Graf <agraf@suse.de> Reviewed-by: Tom Rini <trini@konsulko.com>
Fabien Parent [Thu, 10 Nov 2016 16:16:35 +0000 (17:16 +0100)]
davinci: omapl138_lcdk: keep booting even when MAC address is invalid
If the MAC address specified on the EEPROM is invalid (multicast or
zero address), then u-boot fails to boot. Having a bad MAC address
in the EEPROM should not prevent the system from booting.
This commit changes the error path to just print an error messages
in case of bad MAC address.
Signed-off-by: Fabien Parent <fparent@baylibre.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Alex G [Wed, 9 Nov 2016 04:48:44 +0000 (20:48 -0800)]
board: am335x/mux: Do not hang when encountering a bad EEPROM
In most cases, the SPL and u-boot.img will be on the same boot media.
Since the SPL was loaded by the boot rom, the pinmux will already have
been configured for this media. This, the board will still be able to
boot successfully, or at least reach the u-boot console, where more
recovery options are available.
I've encountered this on a beaglebone black with a corrupted EEPROM.
Removing this check allowed the board to boot successfully. I've also
seen this on EVM-based boards with an unprogrammed EEPROM. On those
boards, for some reason there were no UART messages. This made it look
as if the SOC was dead.
Remove the hang(), as it is not a fatal error. Also reformat the error
message to be clearer as to the cause. The original message made it
appear as if the wrong binary was being loaded.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Ladislav Michl [Fri, 4 Nov 2016 11:59:46 +0000 (12:59 +0100)]
igep00x0: add Hynix timings
Tested on IGEPv2 with Micron MT29F4G16ABBDA3W and
Hynix H27S4G6F2DKA-BM
Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Reviewed-by: Javier Martinez Canillas <javier@samsung.com> Tested-by: Javier Martinez Canillas <javier@samsung.com>
Ladislav Michl [Fri, 4 Nov 2016 11:55:21 +0000 (12:55 +0100)]
igep00x0: disable CONFIG_DISPLAY_BOARDINFO
As a single U-Boot binary can now run on various board modifications,
drop CONFIG_DISPLAY_BOARDINFO as it prints flash memory information
too early to give us chance to easily detect it. Also saves few bytes
as a bonus.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Reviewed-by: Javier Martinez Canillas <javier@samsung.com> Tested-by: Javier Martinez Canillas <javier@samsung.com>
Andre Przywara [Thu, 10 Nov 2016 12:13:23 +0000 (12:13 +0000)]
tools: fix mksunxiboot build for tools-all target
Commit fed329aebe3a ("tools: add mksunxiboot to tools-all target") added
mksunxiboot to the tools-all target, but used the CONFIG_SUNXI symbol
to enable its build. Now commit aec9a0f19f64 ("sunxi: Rename CONFIG_SUNXI
to CONFIG_ARCH_SUNXI"), merged before that, renamed that symbol, so that
the first patch basically gets ineffective.
Adjust the symbol name in tools/Makefile to make it build again.
Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Stephen Warren [Wed, 19 Oct 2016 21:18:47 +0000 (15:18 -0600)]
ARM: tegra186: call secure monitor for all cache-wide ops
An SMC call is required for all cache-wide operations on Tegra186. This
patch implements the two missing hooks now that U-Boot supports them, and
fixes the mapping of "hook name" to SMC call code.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Wed, 19 Oct 2016 21:18:46 +0000 (15:18 -0600)]
armv8: add hooks for all cache-wide operations
SoC-specific logic may be required for all forms of cache-wide
operations; invalidate and flush of both dcache and icache (note that
only 3 of the 4 possible combinations make sense, since the icache never
contains dirty lines). This patch adds an optional hook for all
implemented cache-wide operations, and renames the one existing hook to
better represent exactly which operation it is implementing. A dummy
no-op implementation of each hook is provided.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Wed, 19 Oct 2016 21:18:45 +0000 (15:18 -0600)]
ARM: tegra: translate __asm_flush_l3_cache to assembly
When performing a cache disable function, code must not access DRAM.
That is because when the cache is disabled, it will be bypassed and all
loads and stores will be serviced by RAM. This prevents accessing any
dirty data in the cache. In turn, this means the stack cannot be
used, since that is in RAM. To guarantee that code doesn't use RAM (and
in particular the stack) __asm_flush_l3_cache() must be manually
implemented in assembly, rather than implemented in C since the compiler
won't know not to touch RAM.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Chris Packham [Mon, 31 Oct 2016 21:48:32 +0000 (10:48 +1300)]
net: mvgbe: Fix build error with CONFIG_PHYLIB
Commit 5a49f17481bb ("net: mii: Use spatch to update miiphy_register")
updated the mvgbe implementation of smi_reg_read/smi_reg_write. Prior to
that change mvgbe_phy_read and mvgbe_phy_write where used as wrappers to
satisfy the phylib APIs. Because these functions weren't updated in that
commit build errors where triggered when CONFIG_PHYLIB was enabled.
Fix these build errors by removing mvgbe_phy_read and mvgbe_phy_write
and using smi_reg_read/smi_reg_write directly.
Signed-off-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Stephen Warren [Mon, 12 Sep 2016 17:51:13 +0000 (11:51 -0600)]
ARM: tegra: configure Ethernet address on Tegra186
On Tegra186, the bootloader which runs before U-Boot passes the Ethernet
MAC address to U-Boot using device tree. Extract this value and write it
to the environment, so that the Ethernet uclass picks it up and uses it
for the built-in Ethernet device.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Stephen Warren [Mon, 12 Sep 2016 17:51:12 +0000 (11:51 -0600)]
ARM: tegra: add SoC-level hook for board_late_init()
Extend the Tegra186 implementation of board_late_init() to call a per-SoC
"hook" function. This will allow SoC-specific (rather than Tegra-wide)
functionality to be implemented without the core Tegra code needing to be
aware of the details. While board186.c is currently only used for
Tegra186, it should be applicable to any other future SoC, and perhaps its
simple design could be back-ported to older SoCs in the future too.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Stephen Warren [Fri, 21 Oct 2016 20:46:47 +0000 (14:46 -0600)]
net: add driver for Synopsys Ethernet QoS device
This driver supports the Synopsys Designware Ethernet QoS (Quality of
Service) a/k/a eqos IP block, which is a different design than the HW
supported by the existing designware.c driver. The IP supports many
options for bus type, clocking/reset structure, and feature list. This
driver currently supports the specific configuration used in NVIDIA's
Tegra186 chip, but should be extensible to other combinations quite
easily, as explained in the source.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> # V1 Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Stephen Warren [Fri, 21 Oct 2016 20:46:46 +0000 (14:46 -0600)]
dt: net: add DWC EQoS binding
The Synopsys DWC EQoS is a configurable Ethernet MAC/DMA IP block which
supports multiple options for bus type, clocking and reset structure, and
feature list.
This patch imports the binding from the Linux kernel, including my V3
patch to extend the binding to cover the Tegra186, which is applied for
next-20160912. So far, my changes have been acked by Lars Persson, the
original author of the binding.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fabio Estevam [Tue, 1 Nov 2016 16:58:16 +0000 (14:58 -0200)]
wandboard: Make Ethernet functional again
Since commit ce412b79e7255770 ("drivers: net: phy: atheros: add separate
config for AR8031") ethernet does not work on mx6sabresd.
This commit correctly assigns ar8031_config() as the configuration
function for AR8031 in the same way as done in the Linux kernel.
However, on wandboard design we need some additional configuration,
such as enabling the 125 MHz AR8031 output that needs to be done
in the board file.
This also aligns with the same method that the kernel performs
the AR8031 fixup in arch/arm/mach-imx/mach-imx6q.c.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tomeu Vizoso [Fri, 4 Nov 2016 13:22:15 +0000 (14:22 +0100)]
mkimage: Allow including a ramdisk in FIT auto mode
Adds -i option that allows specifying a ramdisk file to be added to the
FIT image when we are using the automatic FIT mode (no ITS file).
This makes adding Depthcharge support to LAVA much more convenient, as
no additional configuration files need to be kept around in the machine
that dispatches jobs to the boards.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com> Cc: Simon Glass <sjg@chromium.org> Cc: Matt Hart <matthew.hart@linaro.org> Cc: Neil Williams <codehelp@debian.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Sat, 5 Nov 2016 23:34:49 +0000 (19:34 -0400)]
travis-ci: Try harder to build all ARM targets
The way that we have things broken down currently allows for some
combinations of vendor or CPU to not be built. To fix this, create a
new catch-all job that excludes everything we've built elsewhere. For
the sake of simplicity we are allowing for the possibility of some
overlap between the vendor-based jobs and the CPU-based jobs. While
we're in here, make a failed build provide the summary of failure.
Fabio Estevam [Mon, 24 Oct 2016 12:22:06 +0000 (10:22 -0200)]
mx6sabresd: Make Ethernet functional again
Since commit ce412b79e7255770 ("drivers: net: phy: atheros: add separate
config for AR8031") ethernet does not work on mx6sabresd.
This commit correctly assigns ar8031_config() as the configuration
function for AR8031 in the same way as done in the Linux kernel.
However, on mx6sabresd design we need some additional configuration,
such as enabling the 125 MHz AR8031 output that needs to be done
in the board file.
This also aligns with the same method that the kernel performs
the AR8031 fixup in arch/arm/mach-imx/mach-imx6q.c.
Andre Przywara [Thu, 3 Nov 2016 00:56:25 +0000 (00:56 +0000)]
armv8: define get_ticks() for the ARMv8 Generic Timer
For 64-bit ARM systems we provide just a timer_read_counter()
implementation and rely on the generic non-uclass get_ticks() function
in lib/time.c to call the former.
However this function is actually not 64-bit safe, as it assumes a
"long" to be 32-bit. Beside the fact that the resulting uint64_t
isn't bigger than "long" on 64-bit architectures and thus combining two
counters makes no sense, we get all kind of weird results when we try
to OR in the high value shifted by _32_ bits.
So let's avoid that function at all and provide a straight forward
get_ticks() implementation for ARMv8, which also is in line with ARMv7.
This fixes occasional immediate time-out expiration issues I see on the
Pine64 board. The root cause of this needs to be investigated, but this
fix looks like the right thing anyway.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
ifd = open(plugin_file, O_RDONLY|O_BINARY);
>>> CID 153926: Error handling issues (NEGATIVE_RETURNS)
>>> "ifd" is passed to a parameter that cannot be negative.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@konsulko.com> Reported-by: Coverity (CID: 153926) Reviewed-by: Tom Rini <trini@konsulko.com>
Tom Rini [Sat, 29 Oct 2016 21:11:17 +0000 (17:11 -0400)]
travis.yml: Add in uniphier as a job, modify aarch64 builds a bit
- Add in system aarch64-linux-gnu toolchain
- Now that all VMs will have aarch64 available, don't exclude them from
other jobs but instead exclude them from the catch-all aarch64 build
- Add JOB= to the Freescale/ARM build to be clear about what it does.
- Add uniphier as a stand-alone job
Nishanth Menon [Tue, 11 Oct 2016 17:39:05 +0000 (12:39 -0500)]
ti: common: board_detect: Return a valid empty string for un-initialized eeprom
Current logic for query of revision, board_name, config returns
NULL. Users of these functions do a direct strncmp to compare.
Unfortunately, as per conventions require two valid strings to compare
against and the current implementation causes a crash when compared
with NULL.
We'd still like to maintain the simplistic usage of these APIs instead
of redundant if (string) res=strncmp(fn(),"cmp",n); flowing all over
the place.
Hence, since the version, name and config is already pre-initialized
with empty string, just dont check for invalid header in the first
place and return the empty string to the caller.
Jacob Chen [Sat, 8 Oct 2016 05:47:41 +0000 (13:47 +0800)]
rockchip: use rockchip linux partitions layout
Unify the partitions of each chip then it will be more easy for us to
write scripts, tools or guides for rockchip chips.
Those extra partitions mostly are used to be compatible with our
internal loaders (such as miniloader which was same as spl, or
android loader then we can support dual boot)
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Kever Yang [Fri, 7 Oct 2016 09:47:58 +0000 (17:47 +0800)]
rk3288: sdram: auto-detect the capacity
Add support for rk3288 dram capacity auto detect, support DDR3 and
LPDDR3, DDR2 is not supported.
The program will automatically detect:
- channel number
- rank number
- column address number
- row address number
The dts file do not need to describe those info after apply this patch.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Tested-by: Simon Glass <sjg@chromium.org> Tested-by: Vagrant Cascadian <vagrant@debian.org> Tested-by: Vagrant Cascadian <vagrant@debian.org>
Chen-Yu Tsai [Fri, 28 Oct 2016 10:21:38 +0000 (18:21 +0800)]
sunxi: Add support for Cubieboard4
The Cubieboard4 is an A80 SoC based development board from Cubietech.
This board has a UART port, 4 USB host ports, a USB 3.0 OTG connector,
HDMI and VGA outputs, a micro SD slot, 8G eMMC flash, 2G DRAM, a WiFi/BT
combo chip, headphone and microphone jacks, IR receiver, and GPIO headers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Chen-Yu Tsai [Fri, 28 Oct 2016 10:21:37 +0000 (18:21 +0800)]
sunxi: Enable SPL support for A80 Optimus board
The A80 Optimus Board was launched with the Allwinner A80 SoC.
It was jointly developed by Allwinner and Merrii.
This board has a UART port, a JTAG connector, 2 USB host ports, a USB
3.0 OTG connector, an HDMI output, a micro SD slot, 16G eMMC flash,
2G DRAM, a camera sensor interface, a WiFi/BT combo chip, a headphone
jack, IR receiver, and additional GPIO headers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[hdegoede@redhat.com: update existing Merrii_A80_Optimus_defconfig
instead of adding a new defconfig] Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Amit Singh Tomar [Fri, 21 Oct 2016 01:24:30 +0000 (02:24 +0100)]
sunxi: A64: enable USB support
Mostly by adding MACH_SUN50I to some existing #ifdefs enable support
for the the HCI0 USB host controller on the A64.
Fix up some minor 64-bit hiccups on the way.
Add the bare minimum DT bits to the A64 .dtsi and enable the controllers
and the PHY on the Pine64.
This is limited to the first USB controller at the moment, which is
connected to the lower USB socket on the Pine64 board.
[Andre: remove unneeded defines, enable OHCI, add commit message]
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Stefan Mavrodiev [Sat, 29 Oct 2016 12:34:07 +0000 (14:34 +0200)]
sunxi: Update DRAM clock for Olimex A20 boards
Originally dram clock was set to 480MHz, but this behaves
unstable. To improve stability the clock is reduced to 384MHz
Signed-off-by: Stefan Mavrodiev <stefan.mavrodiev@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Andre Przywara [Fri, 21 Oct 2016 00:11:46 +0000 (01:11 +0100)]
sunxi: dts: Pine64: add Ethernet alias
The sun8i-emac driver works fine with the A64 Ethernet IP, but we are
missing an alias entry to trigger the driver instantiation by U-Boot.
Add the line to point U-Boot to the Ethernet DT node.
This enables TFTP boot on the Pine64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
ARCH_SUNXI selects DM_USB, where CONFIG_USB_MAX_CONTROLLER_COUNT
is not used.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Jagan Teki [Thu, 13 Oct 2016 08:49:35 +0000 (14:19 +0530)]
sunxi: Rename CONFIG_SUNXI to CONFIG_ARCH_SUNXI
CONFIG_SUNXI -> CONFIG_ARCH_SUNXI
and removed CONFIG_SUNIX from config_whitelist.txt
Cc: Simon Glass <sjg@chromium.org> Cc: Ian Campbell <ijc@hellion.org.uk> Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Philipp Tomsich [Fri, 28 Oct 2016 10:21:32 +0000 (18:21 +0800)]
sunxi: enable SPL for sun9i
Now that DRAM initialization and clock setup is supported,
we can enable SPL for the A80.
[wens@csie.org: Added commit message] Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Philipp Tomsich [Fri, 28 Oct 2016 10:21:31 +0000 (18:21 +0800)]
sunxi: add initial clock setup for sun9i for SPL
This is a cleaned up version set_pll() from Allwinner's boot0 source
(bootloader/basic_loader/bsp/bsp_for_a80/common/common.c).
[wens@csie.org: Added commit message; style cleanup] Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Philipp Tomsich [Fri, 28 Oct 2016 10:21:30 +0000 (18:21 +0800)]
sunxi: Enable SMP mode for the boot CPU on sun9i (A80)
Since the A80 has many cores which we intend to use in SMP fashion,
we should set the SMP bit for the boot CPU.
[wens@csie.org: Added commit message] Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Philipp Tomsich [Fri, 28 Oct 2016 10:21:29 +0000 (18:21 +0800)]
sunxi: add gtbus-initialisation for sun9i
On sun9i, the GTBUS manages transaction priority and bandwidth
for multiple read ports when accessing DRAM. The initialisation
mirrors the settings from Allwinner's boot0 for now, even though
this may not be optimal for all applications (e.g. headless
systems might want to give priority to IO modules).
Adding a common callout to gtbus_init() from the SPL clock init
with a weakly defined implementation in sunxi/clock.c to fallback
to for platforms that don't require this.
[wens@csie.org: Moved gtbus_sun9i.c to arch/arm/mach-sunxi/; style cleanup] Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Philipp Tomsich [Fri, 28 Oct 2016 10:21:28 +0000 (18:21 +0800)]
sunxi: DRAM initialisation for sun9i
This adds DRAM initialisation code for sun9i, which calculates the
appropriate timings based on timing information for the supplied
DDR3 bin and the clock speeds used.
With this DRAM setup, we have verified DDR3 clocks of up to 792MHz
(i.e. DDR3-1600) on the A80-Q7 using a dual-channel configuration.
[wens@csie.org: Moved dram_sun9i.c to arch/arm/mach-sunxi/; style cleanup] Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[hdegoede@redhat.com: Drop some huge non-documenting #if 0 ... #endif blocks]
[hdegoede@redhat.com: Fix checkpatch warnings] Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Andre Przywara [Fri, 21 Oct 2016 01:24:29 +0000 (02:24 +0100)]
drivers: USB: OHCI: allow compilation for 64-bit targets
OHCI has a known limitation of allowing only 32-bit DMA buffer
addresses, so we have a lot of u32 variables around, which are assigned
to pointers and vice versa. This obviously creates issues with 64-bit
systems, so the compiler complains here and there.
To allow compilation for 64-bit boards which use only memory below 4GB
anyway (and to avoid more invasive fixes), adjust some casts and types
and assume that the EDs and TDs are all located in the lower 4GB.
This fixes compilation of the OHCI driver for the Pine64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Stephen Warren [Wed, 26 Oct 2016 17:05:36 +0000 (11:05 -0600)]
travis-ci: compile with buildman when running test/py
Use buildman to compile any U-Boot binary tested by test/py. This
re-uses all the work done elsewhere to make buildman work within
Travis-CI, in particular related to toolchain downloading and buildman
config file creation.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Heiko Schocher <hs@denx.de>