Ashish Kumar [Thu, 23 Nov 2017 09:03:49 +0000 (14:33 +0530)]
armv8: ls1088a: Unset USE_BOOTCOMMAND in defconfig
Unset USE_BOOTCOMMAND for all ls1088 defconfig files to fix
redefinition error. USE_BOOTCOMMAND was introduced in commit b6251db8c3f ("Kconfig: Introduce USE_BOOTCOMMAND and migrate
BOOTCOMMAND").
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Peng Fan [Thu, 30 Nov 2017 02:07:07 +0000 (10:07 +0800)]
scripts: spl: fix typo
Typo fix: CONIFG->CONFIG
Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Tom Rini <trini@konsulko.com> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Derald D. Woods [Wed, 29 Nov 2017 03:28:55 +0000 (03:28 +0000)]
omap3: evm: Explicitly use DISTRO_DEFAULTS features at startup
[primary] Check MMC 0:1 for /extlinux/extlinux.conf and boot
[fallback 1] Check MMC 0:1 zImage and run mmcbootz
[fallback 2] Check MMC 0:1 uImage and run mmcboot
[fallback 3] Check NAND partitions and run nandboot
If 'extlinux.conf' is not found on MMC 0, the previous boot behavior is
followed.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Neil Armstrong [Mon, 27 Nov 2017 09:35:46 +0000 (10:35 +0100)]
ARM: arch-meson: build memory banks using reported memory from registers
As discussed at [1], the Amlogic Meson GX SoCs can embed a BL31 firmware
and a secondary BL32 firmware.
Since mid-2017, the reserved memory address of the BL31 firmware was moved
and grown for security reasons.
But mainline U-Boot and Linux has the old address and size fixed.
These SoCs have a register interface to get the two firmware reserved
memory start and sizes.
This patch adds a dynamic reservation of the memory zones in the device tree bootmem
reserved memory zone used by the kernel in early boot.
To be complete, the memory zones are also added to the EFI reserved zones.
Depends on patchset "Add support for Amlogic GXL Based SBCs" at [2].
Changes since v1:
- switched the #if to if(IS_ENABLED()) to compile all code paths
- renamed function to meson_board_add_reserved_memory()
- added a mem.h header with comment
- updated all boards ft_board_setup()
Changes since RFC v2:
- reduced preprocessor load
- kept Odroid-C2 static memory mapping as exception
Changes since RFC v1:
- switch to fdt rsv mem table and efi reserve memory
- replaced in_le32 by readl()
Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[trini: Fix warning on khadas-vim over missing <asm/arch/mem.h> Signed-off-by: Tom Rini <trini@konsulko.com>
Andre Przywara [Mon, 27 Nov 2017 00:47:09 +0000 (00:47 +0000)]
armv8: shrink exception table code
In the moment our exception entry code needs 34 instructions, so we
can't use put it directly into the table entry, which offers "only"
32 instructions there. Right now we just put an unconditional branch
there, then use a macro to place the 34 instructions *per entry* after
that. That effectivly doubles the size of our exception table, which
is quite a waste, given that we use it mostly for debugging purposes.
Since the register saving part is actually identical, let's just convert
that macro into a function, and "bl" into it directly from the exception
slot, of course after having saved at least the original LR.
This saves us about 950 bytes of code, which is quite a relief for some
tight SPLs, in particular the 64-bit Allwinner ones.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Simon Glass [Sat, 25 Nov 2017 18:57:33 +0000 (11:57 -0700)]
test: compression: Convert to unit test framework
Adjust this test to use the unit test framework. Drop the two existing
commands for running the tests and replace them with a single
'ut compression' command, with sub-commands.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Continue to have ret = run_test_internal(...) in run_test so ret
is always initialized] Signed-off-by: Tom Rini <trini@konsulko.com>
We are planning to share more code between different NAND based
devices (SPI NAND, OneNAND and raw NANDs), but before doing that
we need to move the existing include/linux/mtd/nand.h file into
include/linux/mtd/rawnand.h so we can later create a nand.h header
containing all common structure and function prototypes.
York Sun [Sat, 18 Nov 2017 19:09:08 +0000 (11:09 -0800)]
mtd: cfi: Fix checking status register feature
Commit 72443c7f7d21 ("mtd: cfi: Add support for status register
polling") added a feature check to determine if status register
is available for certain flash chips. The "lower software bits"
register used to determine this feature is not backward compati-
ble. Older flash chips without this feature has reserved value
0xff. Instead of checking "lower software bits" register, use
CFI primary vendor-specific extended query. Since CFI version
1.4, software features can be read from offset 0x53 according to
document AN201168 from Cypress.
Signed-off-by: York Sun <york.sun@nxp.com> CC: Marek Vasut <marek.vasut@gmail.com> Tested-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
Simon Glass [Sat, 25 Nov 2017 18:57:32 +0000 (11:57 -0700)]
test/py: Allow any unit test suite to be found
The u-boot.sym file is scanned to find unit test suites for execution. At
present it only finds those whose names start with 'dm' or 'env'. This
code is buried in the bowels of the test code so when adding a new suite
it is not easy to discover why it is ignored by the test framework.
There seems to be no need to make this restriction. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Stephen Warren <swarren@nvidia.com>
Simon Glass [Sat, 25 Nov 2017 18:57:31 +0000 (11:57 -0700)]
test: compression: Put test variables in a struct
At present the test setup is somewhat mixed with the test itself. But if
the test setup fails (which it should not) then the test is actually
invalid. Put all the test buffers and sizes in a struct and separate out
the core code into a function.
This will make it easier to move the code to use the unit test framework.
Simon Glass [Sat, 25 Nov 2017 18:57:29 +0000 (11:57 -0700)]
test: Add a command function for test execution
The logic to either iterate through a list of tests or pick a named test
is common to at lest two test suits. Move this logic into a new function
and call it from the environment tests.
Peter Robinson [Thu, 23 Nov 2017 13:14:17 +0000 (13:14 +0000)]
omap2: set the ethaddr as well as the usbethaddr env var to ensure static MAC
The kernel gets the ethernet MAC from the ethaddr variable, the omap boards for
devices with USB based eth adapters just set the usbethaddr which doesn't appear
to get passed to the kernel. The same Raspberry Pi code sets both ethaddr and
usbethaddr so lets do that so linux (tested 4.13 and 4.14) get a static rather
than a random MAC address, while not regressing users of usbethaddr.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
On the RK3399-Q7, we want to trigger a full platform reset (so the
various software stacks supported don't have to deal with the same
complexities over and over again) in case that anything other than a
power-on reset occurred.
To do so, this defines the /config/sysreset-gpio property and has it
point to a GPIO that will perform a power-on reset of the entire
platform.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Philipp Tomsich [Tue, 28 Nov 2017 16:56:11 +0000 (17:56 +0100)]
rockchip: rk3399-puma: add code to allow forcing a power-on reset
The reset circuitry in the RK3399 only resets 'almost all logic' when
a software reset is performed. To make our software maintenance
easier in the future, we want to have the option (controlled by a DTS
property) to force all reset causes other than a power-on reset to
trigger a power-on reset via a GPIO trigger.
This adds the necessary support to the rk3399-puma (i.e. RK3399-Q7)
board-support and the documentation for the new property
(sysreset-gpio) within the /config-node.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Philipp Tomsich [Wed, 22 Nov 2017 16:15:19 +0000 (17:15 +0100)]
rockchip: dts: rk3399-puma: add a 'tsd, usb-port-power' stringlist for USB1
USB1 is connected to the on-module USB 3.0 hub and power to the hub
(actually it's a reset signal, modeled as a fixed regulator, that will
be released) should be enabled only during the first probing of the
device to avoid the hub from entering its low-power mode (where it
tries to attach on a fixed interval, but we always miss the timeslot
when U-Boot has the controller listening).
This adds a 'tsd,usb-port-power' stringlist to enable the
infrastructure in the board-specific usb_hub_reset_devices to find and
control the fixed regulator associated with control of the USB hub.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Philipp Tomsich [Wed, 22 Nov 2017 16:15:18 +0000 (17:15 +0100)]
rockchip: rk3399-puma: implement usb_hub_reset_devices for puma-rk3399
For some versions of the RK3399-Q7 (at least revisions v1.1 and v1.2
are affected), we need to turn on the power for the port connected to
the on-module USB hub only when the device is probed for the first
time to ensure that the hub does not enter a low-power mode (that
U-Boot's USB stack can't deal with).
Note that this is needed for U-Boot only, as Linux eventually manages
to attach the hub even when it has entered into its low-power state
(when the hub wakes up the next time) after a few seconds.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Kever Yang [Thu, 30 Nov 2017 08:51:21 +0000 (16:51 +0800)]
rockchip: rk3036: sdram: correct setting for pll integer mode
According to rk3036 TRM, should be set to '1' for the pll
integer mode, while the '0' means the frac mode.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Thu, 30 Nov 2017 08:51:20 +0000 (16:51 +0800)]
rockchip: rk3036: update clock driver for ddr
After the MASK MACRO update, we need to update the driver at the same time.
This is a fix to: 37943aa rockchip: rk3036: clean mask definition for cru reg
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Thu, 30 Nov 2017 08:51:19 +0000 (16:51 +0800)]
rockchip: rk3036: fix pll config for correct frequency
There is a fixed div-2 between PLL and clk_ddr/clk_ddrphy,
so we need to double to pll output and then ddr can work
in correct frequency.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Tue, 28 Nov 2017 11:30:37 +0000 (12:30 +0100)]
rockchip: board: evb-rk3128: add empty Makefile
Even if the board-specific directory Makefile doesn't have any
targets, it still needs to exist.
This adds a minimal Makefile for the board/rockchip/evb_rk3128
directory and a evk-rk3128.c (as built-in.o needs to be built
for every directory that a Makefile gets run for).
Kever Yang [Tue, 28 Nov 2017 08:04:21 +0000 (16:04 +0800)]
rockchip: rk3128: add sdram driver
RK3128 support up to 2GB DDR3 sdram, one channel, 32bit data width.
This patch is only used for U-Boot, but not for SPL which will
comes later, maybe after we merge all the common code into a common
file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Tue, 28 Nov 2017 08:04:20 +0000 (16:04 +0800)]
rockchip: rk3128: add defconfig for evb-rk3128
Enable board config for evb-rk3128.
Serial output and eMMC works in this version.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Tue, 28 Nov 2017 08:04:19 +0000 (16:04 +0800)]
rockchip: rk3128: add evb-rk3128 support
evb-rk3128 is an evb from Rockchip based on rk3128 SoC:
- 2 USB2.0 Host port;
- 1 HDMI port;
- 2 10/100M eth port;
- 2GB ddr;
- 16GB eMMC;
- UART to USB debug port;
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Tue, 28 Nov 2017 08:04:18 +0000 (16:04 +0800)]
rockchip: rk3128: add pinctrl driver
Add rk3128 pinctrl driver and grf/iomux structure definition.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Tue, 28 Nov 2017 08:04:17 +0000 (16:04 +0800)]
rockchip: rk3128: add clock driver
Add rk3128 clock driver and cru structure definition.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Tue, 28 Nov 2017 08:04:16 +0000 (16:04 +0800)]
rockchip: rk3128: add soc basic support
RK3128 is a SoC from Rockchip with quad-core Cortex-A7 CPU
and mali400 GPU. Support Nand flash, eMMC, SD card, USB 2.0 host
and device, HDMI/LVDS/MIPI display.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Tue, 28 Nov 2017 08:04:15 +0000 (16:04 +0800)]
rockchip: rk3128: add device tree file
Add dts binding header for rk3128, files origin from kernel.
Series-Changes: 2
- fix i2c address
- add saradc and usb phy node
- emmc using fifo mode for there is no dma support in rk3128 emmc
- add some clock id in cru.h
Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Andy Yan [Mon, 27 Nov 2017 11:59:45 +0000 (19:59 +0800)]
rockchip: board: evb_rv1108: update README
After commit d962e5dadc2c("rockchip: mkimage: use spl_boot0 for all Rockchip SoCs"),
the mkimage will not pad the Tag memroy, so we shoud
pass a Taged ddr.bin/spl.bin to it.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Sun, 26 Nov 2017 23:18:42 +0000 (00:18 +0100)]
MAINTAINERS: update maintained files for Rockchip
With some of the recent cleanups (e.g. moving the DRAM controller
drivers for Rockchip devices to drivers/ram/rockchip), the files
and paths listed in MAINTAINERS no longer covered what really is
looked after as part of the Rockchip port.
This commit updates the files/paths listed in MAINTAINERS for the
Rockchip port. I am certain, though, that this will have missed some
additional paths that should have been included...
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Chris Packham [Tue, 28 Nov 2017 21:38:34 +0000 (10:38 +1300)]
arm: mvebu: correct comments around cas_wl/cas_l
The order of members in struct hws_topology_map is cas_wl, cas_l. The
comments in the original db-88f6820-gp.c had this wrong and have been
copied to other Armada-385 based boards. Practically this hasn't made a
difference since all these boards set both cas_wl and cas_l to 0
(autodetect) but if there were ever a board that did need to set these
explicitly they would run into unexpected issued.
Update the comments to reflect the correct order of structure members.
Reported-by: Tobi Wulff <tobi.wulff@alliedtelesis.co.nz> Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
Baruch Siach [Sun, 26 Nov 2017 07:21:23 +0000 (09:21 +0200)]
arm64: mvebu: armada-7k/8k: drop useless #ifdef
CONFIG_ENV_IS_IN_NAND has been removed in commit 2be296538e2e (Convert
CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig).
CONFIG_ENV_IS_IN_SPI_FLASH has been removed in commit 91c868fe7cd
(Convert CONFIG_ENV_IS_IN_SPI_FLASH to Kconfig). The environment #ifdef
is now empty. Remove it.
Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Wed, 29 Nov 2017 15:23:31 +0000 (16:23 +0100)]
x86: lib: Implement standalone __udivdi3 etc instead of libgcc ones
This patch removes the inclusion of the libgcc math functions and
replaces them by functions coded in C, taken from the coreboot
project. This makes U-Boot building more independent from the toolchain
installed / available on the build system.
The code taken from coreboot is authored from Vadim Bendebury
<vbendeb@chromium.org> on 2014-11-28 and committed with commit
ID e63990ef [libpayload: provide basic 64bit division implementation]
(coreboot git repository located here [1]).
I modified the code so that its checkpatch clean without any
functional changes.
[1] git://github.com/coreboot/coreboot.git
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
The error message with FIT style image mentioned in the above commit
only happens when booting using FIT image containing bzImage kernel
and without setup node (setup.bin). The current documentation for
x86 FIT support in doc/uImage.FIT/x86-fit-boot.txt mentions that
kernel's setup.bin file is required for building x86 FIT images.
The above commit breaks FIT images generated as described in the
documentation. Revert it to allow booting with images built in the
documented way.
Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Stefan Roese <sr@denx.de> Acked-by: Bin Meng <bmeng.cn@gmail.com>
Anton Gerasimov [Tue, 14 Nov 2017 17:47:16 +0000 (18:47 +0100)]
x86: qemu: Move Cache-As-RAM memory from area mapped to ROM
ROM has been made read-only in qemu recently (namely commit 208fa0e4:
"pc: make 'pc.rom' readonly when machine has PCI enabled"). So this
patch restores compatibility between U-Boot and qemu.
Signed-off-by: Anton Gerasimov <anton@advancedtelematic.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: mention qemu commit title in the commit message] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Neil Armstrong [Fri, 24 Nov 2017 08:54:41 +0000 (09:54 +0100)]
fat: Use cache aligned buffers for fat_opendir
Before this patch one could receive following errors when executing "fatls"
command on machine with cache enabled (ex i.MX6Q) :
=> fatls mmc 0:1
CACHE: Misaligned operation at range [4f59dfc8, 4f59e7c8]
CACHE: Misaligned operation at range [4f59dfc8, 4f59e7c8]
ERROR: v7_outer_cache_inval_range - start address is not aligned - 0x4f59dfc8
ERROR: v7_outer_cache_inval_range - stop address is not aligned - 0x4f59e7c8
CACHE: Misaligned operation at range [4f59dfc8, 4f59e7c8]
CACHE: Misaligned operation at range [4f59dfc8, 4f59e7c8]
ERROR: v7_outer_cache_inval_range - start address is not aligned - 0x4f59dfc8
ERROR: v7_outer_cache_inval_range - stop address is not aligned - 0x4f59e7c8
To alleviate this problem - the calloc()s have been replaced with
malloc_cache_aligned() and memset().
After those changes the buffers are properly aligned (with both start
address and size) to SoC cache line.
Philipp Tomsich [Tue, 21 Nov 2017 22:29:40 +0000 (23:29 +0100)]
env: suppress a spurious warning with GCC 7.1
GCC 7.1 seems to be smart enough to track val through the various
static inline functions, but not smart enough to see that val will
always be initialised when no error is returned. This triggers
the following warning:
env/mmc.c: In function 'mmc_get_env_addr':
env/mmc.c:121:12: warning: 'val' may be used uninitialized in this function [-Wmaybe-uninitialized]
To make it easier for compiler to understand what is going on, let's
initialise val.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
spl: make CONFIG_OF_EMBED pass dts through fdtgrep
Building spl with CONFIG_OF_EMBED enabled results in an error message
on my board: "SPL image too big". This is because the fdtgrep build
step is only executed for CONFIG_OF_SEPARATE.
Fix this by moving the fdtgrep build step ('cmd_fdtgreo') from
scripts/Makefile.spl to dts/Makefile so that the reduced dtb is
available for all kinds of spl builds.
The resulting variable name for the embedded device tree blob changes,
too, which is why common.h and fdtdec.c have tiny changes.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Adam Ford [Mon, 20 Nov 2017 15:56:03 +0000 (09:56 -0600)]
ARM: dts: Rename logicpd-toredp-37xx-devkit in U-Boot
In U-Boot, this device tree is compatible with both the Torpedo and
SOM-LV kits. Let's rename it in the device tree since the U-Boot code and
show a more generic OMAP3 name. The code auto detects between the two and
loads the proper DTB file for Linux. This would eliminate the SOM-LV showing
the name Torpedo during boot and hopefully eliminate some confusion.
Add a header for SAMA5D2 SMC since it's not compatible with
SAMA5D3 one.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
[wenyou: fix the wrong base address of the SMC register] Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
mmc: atmel_sdhci: not on capabilities to set gck rate
The capabilities have default values which doesn't reflect the reality
when it concerns the base clock and the mul value. Use a fixe rate
for the gck. 240 MHz is an arbitrary choice, it is a multiple of the
maximum SD clock frequency handle by the controller and it allows to
get a 400 kHz clock for the card initialisation.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Wenyou Yang [Fri, 17 Nov 2017 06:50:22 +0000 (14:50 +0800)]
clk: at91: clk-generated: fix incorrect index of clk source
Differentiate the generic clock source selection value from the parent
clock index to fix the incorrect assignment of the generic clock
source selection.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Patrice Chotard [Wed, 15 Nov 2017 12:14:52 +0000 (13:14 +0100)]
clk: clk_stm32fx: add clock configuration for mmc usage
MMC block needs 48Mhz source clock, for that we choose
to select the SAI PLL.
Update also stm32_clock_get_rate() to retrieve the MMC
clock source needed in MMC driver.
STM32F4 uses a different RCC variant than STM32F7. For STM32F4
sdmmc clocks bit are located into dckcfgr register whereas there
are located into dckcfgr2 registers on STM32F7.
In both registers, bits CK48MSEL and SDMMC1SEL are located at
the same position.
Patrice Chotard [Wed, 15 Nov 2017 12:14:51 +0000 (13:14 +0100)]
dm: misc: bind STM32F4/F7 clock from rcc MFD driver
Like STM32H7, now STM32F4/F7 clock drivers are binded by
MFD stm32_rcc driver.
This also allows to add reset support to STM32F4/F7 SoCs family.
As Reset driver is not part of SPL supported drivers, don't bind it
in case of SPL to avoid that stm32_rcc_bind() returns an error.
Patrice Chotard [Wed, 15 Nov 2017 12:14:47 +0000 (13:14 +0100)]
clk: stm32f7: add STM32F4 support
STM32F4 and STM32F7 RCC clock IP are very similar.
Same driver can be used to managed RCC clock for
these 2 SoCs.
Differences between STM32F4 and F7 will be managed using
different compatible string :
_ overdrive clock is only supported by STM32F7
_ different sys_pll_psc parameters can be used between STM32F4
and STM32F7.
Patrice Chotard [Wed, 15 Nov 2017 12:14:46 +0000 (13:14 +0100)]
ARM: DTS: stm32: update rcc compatible for STM32F746
Align the RCC compatible string with the one used by kernel.
It will allow to use the same clock driver for STM32F4
and STM32F7 and to manage the differences between the 2 SoCs
Add a dedicated stm32f7 compatible string to use clk_stm32f7
driver with both STM32F4 and STM32F7 SoCs.
It will be needed to manage differences between these 2 SoCs.
tools: env: Add support for direct read/write UBI volumes
Up to now we were able to read/write environment data from/to UBI
volumes only indirectly by gluebi driver. This driver creates NAND MTD
on top of UBI volumes, which is quite a workaroung for this use case.
Add support for direct read/write UBI volumes in order to not use
obsolete gluebi driver.
Forward-ported from this patch:
http://patchwork.ozlabs.org/patch/619305/
Original patch: Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Forward port: Signed-off-by: S. Lockwood-Childs <sjl@vctlabs.com>
projects / u-boot / log