Michal Simek [Tue, 11 Nov 2014 14:45:36 +0000 (15:45 +0100)]
Revert "lib: bootm: add missing include"
This is a MIME GnuPG-signed message. If you see this text, it means that
your E-mail or Usenet software does not support MIME signed messages.
The Internet standard for MIME PGP messages, RFC 2015, was published in 1996.
To open this message correctly you will need to install E-mail or Usenet
software that supports modern Internet standards.
Masahiro Yamada [Tue, 11 Nov 2014 13:18:22 +0000 (22:18 +0900)]
ARM: UniPhier: call pin_init() also in the normal boot
CONFIG_UNIPHIER_SERIAL has been moved to Kconfig and
it is defined in ./.config but not in spl/.config,
so pin_init() should be called from the normal image
so that UART works correctly.
Masahiro Yamada [Tue, 11 Nov 2014 12:50:41 +0000 (21:50 +0900)]
ARM: UniPhier: decrease pre-reloc malloc area size
In the current implementation of the boot sequence of UniPhier
platform, 32KB temporary RAM is available before relocation.
The malloc area and the stack shares the 32KB area.
With CONFIG_SYS_MALLOC_F_LEN set to 0x7000 (28KB), only 0x1000 (4KB)
is left for the stack. In some use cases, the system hangs up
with stack over-flow.
Even with driver-model UART enabled, the malloc area of 0x2000 (8KB)
should be enough.
Masahiro Yamada [Fri, 7 Nov 2014 12:08:52 +0000 (21:08 +0900)]
ARM: UniPhier: add set_pinsel macro for use in assembly code
The function sg_set_pinsel is useful for switching I/O pins
but it can be only used in C code. This commit adds a simple
macro that is available in asm code.
Masahiro Yamada [Fri, 7 Nov 2014 09:48:33 +0000 (18:48 +0900)]
usb: UniPhier: add UniPhier on-chip EHCI host driver support
Support EHCI host driver used on Panasonic UniPhier platform.
Since Device Tree is not supported on UniPhier yet, the base address
of USB cores are passed from board files (platdevice.c).
TODO for me:
Move the base address to device trees.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Marek Vasut <marex@denx.de>
Masahiro Yamada [Wed, 5 Nov 2014 05:25:15 +0000 (14:25 +0900)]
ARM: UniPhier: reset on-board devices on start-up
If a support card is attached to the main board, the on-board
SMSC9118 LAN controller is available. It must be kept in reset
state for a while on start-up.
When the board is kicked via a debbuger rather than pushing the
hardware reset button, on-board chips are not reset; in this case
the reset signals should be asserted by software.
Dominik Muth [Thu, 28 Aug 2014 10:25:27 +0000 (12:25 +0200)]
Added support for comments in input to mkenvimage.
This patch adds support for comments in the input to mkenvimage, i.e. in
the environment source: All lines starting with a # in the firs column
will be ignored.
Jorgen Lundman [Fri, 7 Nov 2014 01:08:35 +0000 (10:08 +0900)]
ZFS: Clean up cppcheck warnings where relevant, leaked memory etc
In a message from Wolfgang Denk highlighting warnings from cppcheck,
the patch will address those that are correctly diagnosed. Some are
false-positives:
> [fs/zfs/zfs.c:937]: (error) Memory leak: l
dmu_read() allocates "l" if successful, so error-case should not free
it.
> [fs/zfs/zfs.c:1141]: (error) Memory leak: dnbuf
dmu_read() allocates "dnbuf" if successful, so error-case should not
free it.
> [fs/zfs/zfs.c:1372]: (error) Memory leak: osp
zio_read() allocates "osp" if successful, so error-case should
not free it.
> [fs/zfs/zfs.c:1726]: (error) Memory leak: nvlist
int_zfs_fetch_nvlist() allocates "nvlist" if successful, so error-case
should not free it.
i2c: rcar_i2c: Fix order of restart and clear status
In case of repeated START condition, the restart has to be kicked
before clear status (MSR register). If it is kicked after clear status,
R-Car I2C may transfer data (TXD register) or receive data (RXD register)
instead of transferring slave address (MAR register).
Shaveta Leekha [Mon, 3 Nov 2014 05:13:14 +0000 (10:43 +0530)]
drivers/i2c/fsl_i2c: Change CONFIG_I2C_TIMEOUT to 100ms
Some slow I2C devices like Power Monitor(ZM7304) at times
do not work well with low timeout value, so I2C bus get stuck
during read cycle with this device, changing it to 100ms from
10ms works fine
A lot of other i2c drivers like mxc and i2c drivers of BOOTROM
also use relax timeouts to give sufficient ticks to work well
with slower devices
Dirk Eibach [Wed, 29 Oct 2014 14:56:44 +0000 (15:56 +0100)]
ppc4xx: Handle i2c stuck on combined xfer
ppc4xx i2c master gets stuck on errors while repeated start is
active. Can be easily reproduced by "i2c md" on an unpopulated
i2c address. There is not stop condition given, scl remains
pulled low.
The only way out seems to be doing a stop manually and then a
soft reset.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc> Reviewed-by: Stefan Roese <sr@denx.de>
Dirk Eibach [Wed, 29 Oct 2014 14:56:43 +0000 (15:56 +0100)]
ppc4xx: Fix i2c repeated start
Debugging some i2c trouble I saw on my scope that repeated
start is not working properply. The 4xx even held clock pulled down
after transfers. Having a look in the driver I realized
that IIC_CNTL_RPST is set on that part of the transfer that should
begin with a repeated start. But repeated start is about not sending a
stop condition, so IIC_CNTL_RPST has to be set on the last transfer
before the repeated start happens.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc> Reviewed-by: Stefan Roese <sr@denx.de>
Soeren Moch [Sat, 8 Nov 2014 06:02:14 +0000 (07:02 +0100)]
usb_storage: blacklist Enclosure Service Devices
Skip enclosure service devices when probing for usb storage devices.
This avoids long timeouts when probing for external usb harddisks
which provide "Enclosure Services".
Signed-off-by: Soeren Moch <smoch@web.de>
--
This is a new version of the patch
"usb_storage: skip all unknown devices when probing"
http://http://lists.denx.de/pipermail/u-boot/2014-November/194622.html
Cc: Marek Vasut <marex@denx.de> Cc: Tom Rini <trini@ti.com>
Wolfgang Denk [Thu, 6 Nov 2014 13:03:01 +0000 (14:03 +0100)]
common/cmd_fitupd.c: restore corrupted file
This file got corrupted by the automatic editin of commit 1a45966 "Add
GPL-2.0+ SPDX-License-Identifier to source files"; restore the
opiginal content and manually insert the SPDX ID.
The bug was detected by running cppcheck, which reported:
[common/cmd_fitupd.c:8]: (error) Invalid number of character ({) when
these macros are defined: 'CONFIG_UPDATE_TFTP'.
Wolfgang Denk [Thu, 6 Nov 2014 13:02:57 +0000 (14:02 +0100)]
cppcheck cleanup: fix nullPointer errors
There are a number of places where U-Boot intentionally and legally
accesses physical address 0x0000, for example when installing
exception vectors on systems where these are located in low memory.
Add "cppcheck-suppress nullPointer" comments to silence cppcheck
where this is intentional and legal.
Dominic Sacré [Tue, 4 Nov 2014 23:30:18 +0000 (00:30 +0100)]
tools/env: Fix environment size and CRC on 64-bit hosts
On architectures where 'long' is 64 bit, the u-boot environment
as seen by the fw_env tools was missing 4 bytes.
This patch fixes getenvsize(), and thus also ensures that the
environment's CRC32 checksum is calculated correctly.
Signed-off-by: Dominic Sacré <dominic.sacre@gmx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Tom Rini <trini@ti.com>
Masahiro Yamada [Thu, 30 Oct 2014 02:06:12 +0000 (11:06 +0900)]
kconfig: sync kconfig files with Linux 3.18-rc1
This commit imports Kconfig updates from Linux 3.18-rc1.
'kvmconfig' and 'tinyconfig' help message have been commented out
since they are unavailable at least now; in the future perhaps
we can implement 'tinyconfig' to disable most of CONFIG_CMD_* to
create a very small U-Boot image.
[1] commit 3aaefce10351 by Josh Triplett
x86, platform, kconfig: move kvmconfig functionality to a helper
[2] commit 0da1d4a0b951 by Josh Triplett
x86: Add "make tinyconfig" to configure the tiniest possible kernel
[3] commit c40724d3f381 by Brian Norris
kconfig: lxdialog: fix spelling
[4] commit 7285996aa000 by Brian Norris
kconfig: nconfig: fix multi-byte UTF handling
This is due to a NULL pointer dereference of in_str->p in static_peek().
The problem is that the exit condition for the loop in
parse_stream_outer() checks for rcode not being -1, but rcode is only
ever 0 or 1.
Signed-off-by: Rabin Vincent <rabin@rab.in> Acked-by: Simon Glass <sjg@chromium.org) Tested-by: Simon Glass <sjg@chromium.org)
Rabin Vincent [Wed, 29 Oct 2014 22:21:38 +0000 (23:21 +0100)]
sandbox: init cli for -c
sandbox crashes if a variable is set in the -c command, because
hush's top_vars is not allocated. Call cli_init() from sandbox
to ensure this is done before we execute the -c command.
Rabin Vincent [Wed, 29 Oct 2014 22:21:37 +0000 (23:21 +0100)]
dlmalloc: ensure gd is set for early alloc
Attempting to run the sandbox leads to a segfault, because some dynamic
libraries (outside of u-boot) attempt to use malloc() to allocate memory
before u-boot's gd variable is initialized.
Check for gd not being NULL in the SYS_MALLOC_F_LEN handling, so that
malloc() doesn't crash when called at this point.
$ gdb -q --args ./u-boot
(gdb) r
Program received signal SIGSEGV, Segmentation fault.
0x0000000000412b9b in malloc (bytes=bytes@entry=37) at common/dlmalloc.c:2184
2184 if (!(gd->flags & GD_FLG_RELOC)) {
(gdb) p gd
$1 = (gd_t *) 0x0
(gdb) bt
#0 0x0000000000412b9b in malloc (bytes=bytes@entry=37) at common/dlmalloc.c:2184
#1 0x00007ffff75bf8e1 in set_binding_values (domainname=0x7ffff11f4f12 "libgpg-error", dirnamep=0x7fffffffe168, codesetp=0x0)
at bindtextdom.c:228
#2 0x00007ffff75bfb4c in set_binding_values (codesetp=0x0, dirnamep=0x7fffffffe168, domainname=<optimized out>) at bindtextdom.c:350
#3 __bindtextdomain (domainname=<optimized out>, dirname=0x7ffff11f4f00 "/usr/share/locale") at bindtextdom.c:348
#4 0x00007ffff11eca17 in ?? () from /lib/x86_64-linux-gnu/libgpg-error.so.0
#5 0x00007ffff7dea9fa in call_init (l=<optimized out>, argc=argc@entry=1, argv=argv@entry=0x7fffffffe208,
env=env@entry=0x7fffffffe218) at dl-init.c:78
#6 0x00007ffff7deaae3 in call_init (env=0x7fffffffe218, argv=0x7fffffffe208, argc=1, l=<optimized out>) at dl-init.c:36
#7 _dl_init (main_map=0x7ffff7ffe1a8, argc=1, argv=0x7fffffffe208, env=0x7fffffffe218) at dl-init.c:126
#8 0x00007ffff7ddd1ca in _dl_start_user () from /lib64/ld-linux-x86-64.so.2
Signed-off-by: Rabin Vincent <rabin@rab.in> Acked-by: Simon Glass <sjg@chromium.org>
Tom Rini [Sat, 25 Oct 2014 11:38:31 +0000 (07:38 -0400)]
power_spi.c: Rewrite pmic_reg function
The pmic_spi_free function isn't ever used, and as the frameworks stand
today, cannot be, so remove it. Integrate the probe function into
pmic_reg as it's not really a "probe" today. Finally, add an err label
for the common failure cases.
Noam Camus [Wed, 22 Oct 2014 14:17:49 +0000 (17:17 +0300)]
image-fdt: boot_get_fdt() return value when no DTB exists
I believe that when no DTB is around we should return 1.
This why I fixed such scenarious to not return zero anymore.
Else kernel might get NULL pointer to DTB which doesn't exists.
Marek Vasut [Sat, 11 Oct 2014 16:42:58 +0000 (18:42 +0200)]
net: smc911x: Keep MAC programmed
Make sure to keep the MAC address programmed in the SMC911x ADDRH
and ADDRL registers. Linux can read those registers to determine
the MAC address on EEPROM-less configurations.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Tom Rini <trini@ti.com>
Masahiro Yamada [Thu, 6 Nov 2014 18:32:07 +0000 (03:32 +0900)]
generic-board: make compile-time noise for non-generic boards
Commit 0f605c1501f6 (Start the deprecation process for generic board)
added a run-time warning message. Let's be noisier for non-generic
boards to inform the dead line of the conversion.
This commit intentionally outputs a warning message to stdout.
We still have many unconverted boards. If we print the message
to stderr, MAKEALL and buildman will report tons of broken boards
and really important information will be buried.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@ti.com>
Stefan Roese [Fri, 7 Nov 2014 12:50:30 +0000 (13:50 +0100)]
arm: socfpga: Add socfpga_spim_enable() to reset_manager.c
This function will be needed by the upcoming Designware master SPI
driver. As the SPI master controller is held in reset by the current
Preloader implementation. So we need to release the reset for the
driver to communicate with the controller.
This function is called from arch_early_init_r() if the SPI
driver is enabled.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Chin Liang See <clsee@altera.com> Cc: Dinh Nguyen <dinguyen@altera.com> Cc: Vince Bridgers <vbridger@altera.com> Cc: Marek Vasut <marex@denx.de> Cc: Pavel Machek <pavel@denx.de>
Stefan Roese [Fri, 7 Nov 2014 13:10:41 +0000 (14:10 +0100)]
arm: socfpga: Add DT support for SoCFPGA and add socfpga_socrates target
This patch includes the latest DT sources for socfpga from the current
Linux kernel. And enables CONFIG_OF_CONTROL for the new build target
"socfpga_socrates" (the EBV SoCrates board) to make use of this new DT
support.
Until this patch, the only SoCFPGA U-Boot target in mainline is
"socfpga_cyclone5". This build target is not (yet) changed to support
DT. So nothing changes for this target. Even though the long-term
goal should be to move all SoCFPGA targets over to DT.
One of the reasons to enable DT support in SoCFPGA is, that I need to
support multiple different SPI controllers for this platform. This is
the QSPI Cadence controller and the Designware SPI master controller.
Both are implemented in the SoCFPGA. And enabling both controllers is
only possible by using the new driver model (DM). The DM SPI code
only supports DT based probing. So it was easier to move SoCFPGA to
DT than to add the (deprecated) platform-data based probing to the
DM SPI suport.
Note that the image with the dtb embedded is u-boot-dtb.img. This needs
to be used now for those DT enabled boards instead of u-boot.img.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Marek Vasut <marex@denx.de> Cc: Chin Liang See <clsee@altera.com> Cc: Dinh Nguyen <dinguyen@altera.com> Cc: Vince Bridgers <vbridger@altera.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Pavel Machek <pavel@denx.de> Cc: Simon Glass <sjg@chromium.org>
Igor Grinberg [Wed, 5 Nov 2014 12:25:35 +0000 (14:25 +0200)]
omap3: cm-t3517: add basic board support
CompuLab cm-t3517 is Computer on Module (CoM) based on AM3517 SoC.
Features: up to 256MB DDR2, up to 512MB NAND, USB hub, mUSB, WiFi, BT,
Analog audio codec, touch screen controller, LED.
Add basic support including:
LED, Serial console, NAND, MMC, GPIO, I2C, 256MB DRAM.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Igor Grinberg [Mon, 3 Nov 2014 09:32:23 +0000 (11:32 +0200)]
omap: hsmmc: assume cd gpio is active low
Switch the default CD GPIO polarity to active low.
The current hsmmc driver assumption that the CD GPIO is active high, but
in the real hardware, usually the opposite holds.
The usual SD card socket has a mechanical switch which is grounded as
soon as a card is inserted.
Of course there might be some board logic which inverts the signal, but
as far as current users are concerned, there is no such logic.
Current U-Boot users either not using the CD functionality, or have a
different way (e.g. external to SoC GPIO controller) for checking the
card presence.
This patch also brings the polarity assumption in line with the Linux
kernel and adds appropriate comments.
This patch also might spare issues once the TWL GPIO driver will be
converted to the DM.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Cc: Dmitry Lifshitz <lifshitz@compulab.co.il> Reviewed-by: Tom Rini <trini@ti.com>
Igor Grinberg [Mon, 3 Nov 2014 09:32:22 +0000 (11:32 +0200)]
omap3: cm-t35: move get_board_serial() fallback
The fallback is used for cases when CONFIG_SERIAL_TAG defined, but the
eeprom is not used.
The fallback is useful for more than one CompuLab board, so move it to a
common location.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Reviewed-by: Tom Rini <trini@ti.com>
Igor Grinberg [Mon, 3 Nov 2014 09:32:20 +0000 (11:32 +0200)]
omap3: cm-t35: extract the splash code from board
The splash screen loading code can be reused by other compulab boards.
For now extract it to a common location for further reuse.
This also switches the splash code dependency from CONFIG_LCD to
CONFIG_SPLASH_SCREEN as it should normally be.
In addition this patch fixes the accidental dependency of the
get_board_mem_timings() function on CONFIG_LCD, by just moving the
splash code and leaving the above function intact.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Reviewed-by: Tom Rini <trini@ti.com>
Igor Grinberg [Wed, 5 Nov 2014 11:29:54 +0000 (13:29 +0200)]
am335x: make get_board_rev() function weak
Current get_board_rev() function returns a hard coded value which is
obviously incorrect for the majority of boards.
Allow boards to provide a correct implementation by making this
function weak.
In addition open code the trivial and useless BOARD_REV_ID define and
adjust the comment.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Cc: Tom Rini <trini@ti.com>
keystone2: config: align names of images with MCSDK
The Multicore Software Development Kit (MCSDK) provides foundational
software for TI KeyStone II device platforms. It's supposed to be used
with uboot, and it's convenient to have the same names for images, so
correct environment image names according to the last MCSDK3.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
keystone2: config: restructure handling of default env settings
Currently to customize env for various ks2 boards, individual
variables such as NAME_FS etc are defined and included in the
common config.h to define CONFIG_EXTRA_ENV_SETTINGS. This
doesn't scale well if a variable is not applicable on a
specific board. Using this scheme, we have to define variables
with empty value and it's ugly. Instead, to allow board specific
customization of default env variable, define a common
CONFIG_EXTRA_ENV_KS2_SETTINGS for all common variables and define
board specific variables in individual board specific config.h
using CONFIG_EXTRA_ENV_KS2_BOARD_SETTINGS. Use the common and board
specific variables to define CONFIG_EXTRA_ENV_SETTINGS. This way
more variables can be added in future for individual boards
without affecting the other config.h files.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
Hao Zhang [Thu, 30 Oct 2014 16:59:43 +0000 (18:59 +0200)]
net: phy: marvell: add errata w/a for 88E151* chips
As per Marvell Release Notes - Alaska 88E1510/88E1518/88E1512/88E1514
Rev A0, Errata Section 3.1 Marvell PHY has an errata which requires
that certain registers get written in order to restart
autonegotiation.
Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> Reviewed-by: Stefan Roese <sr@denx.de>
Khoronzhuk, Ivan [Wed, 29 Oct 2014 11:09:32 +0000 (13:09 +0200)]
net: keystone_serdes: add keystone K2L SoC support
Keystone2 Lamar SoC uses the same keystone SerDes driver.
All Keystone2 EVM boards currently use SerDes driver, so move
CONFIG_TI_KEYSTONE_SERDES to common configuration file.
Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
projects / u-boot / log