Wolfgang Denk [Mon, 13 Mar 2006 11:37:35 +0000 (12:37 +0100)]
Apply SoC concept to arm926ejs CPUs, i.e. move the SoC specific timer and
cpu_reset code from cpu/$(CPU) into the new cpu/$(CPU)/$(SOC) directories
Patch by Andreas Engel, 13 Mar 2006
Stefan Roese [Mon, 13 Mar 2006 10:16:36 +0000 (11:16 +0100)]
Change max size of uncompressed uImage's to 8MByte and add
CFG_BOOTM_LEN to adjust this setting.
As mentioned by Robin Getz on 2005-05-24 the size of uncompressed
uImages was restricted to 4MBytes. This default size is now
increased to 8Mbytes and can be overrided by setting CFG_BOOTM_LEN
in the board config file.
Wolfgang Denk [Sun, 12 Mar 2006 23:50:48 +0000 (00:50 +0100)]
Change the sequence of events in soft_i2c.c:send_ack() to keep from
incorrectly generating start/stop conditions on the bus.
Patch by Andrew Dyer, 26 Jul 2005
Wolfgang Denk [Sun, 12 Mar 2006 23:46:05 +0000 (00:46 +0100)]
Fix bug in [id]cache_status commands for MPC85xx processors;
should look at LSB of L1CSRn registers to determine if L1 cache is
enabled, not the MSB.
Patch by Murray Jensen, 19 Jul 2005
Wolfgang Denk [Sun, 12 Mar 2006 01:10:00 +0000 (02:10 +0100)]
Add ADI Blackfin support
- add support for Analog Devices Blackfin BF533 CPU
- add support for the ADI BF533 Stamp uClinux board
- add support for the ADI BF533 EZKit board
Patches by Richard Klingler, June 11th 2005:
Wolfgang Denk [Sun, 12 Mar 2006 00:48:55 +0000 (01:48 +0100)]
RPXlite configuration fixes
- Use correct flash sector size
- Use correct memory test end address
- Add support for bzip2 compression
- Various small fixes
Patch by Yuli Barcohen, 05 Jun 2005
Wolfgang Denk [Sun, 12 Mar 2006 00:45:44 +0000 (01:45 +0100)]
Memory configuration changes for ZPC.1900 board
- Fix SDRAM timing on both local bus and 60x bus
- Add support for second flash bank (SIMM)
- Change boot flash base
Patch by Yuli Barcohen, 05 Jun 2005
NAND finally working. Two bugs fixed:
* For READ_STATUS and READID commands always 8 bytes need to be read from
NDDB. Otherwise they stay there and get send to flash as the first data
word when writing.
* In nand_base.c the oob variable is not reset so this->oob_buf is
overwritten what eventually screws up the bad block descriptor table.
Wolfgang Denk [Mon, 6 Mar 2006 10:25:22 +0000 (11:25 +0100)]
Merge the new NAND code (testing-NAND brach); see doc/README.nand
Rewrite of NAND code based on what is in 2.6.12 Linux kernel
Patch by Ladislav Michl, 29 Jun 2005
Re-factoring the legacy NAND code (legacy NAND now only in board-specific
code and in SoC code). Boards using the old way have CFG_NAND_LEGACY and
BOARDLIBS = drivers/nand_legacy/libnand_legacy.a added. Build breakage for
NETTA.ERR and NETTA_ISDN - will go away when the new NAND support is
implemented for these boards.
Lots of new stuff:
* Debug message can be turned on and off.
* Waiting for events now times out.
* Implemented RESET command.
* Added appropriate nand_bbt_descriptor and nand_oobinfo.
Remaining Problems:
* Read Status still behaves weird an returns invalid stuff sometimes.
* ECC Placement does not respect our scheme in nand_oobinfo.
Moved the waiting loop for "Read Data Request" RDDREQ into the
delta_cmdfunc function, because this bit is only set once after a command
is sent and this allows read functions to be called multiple times.
Stefan Roese [Tue, 28 Feb 2006 14:29:58 +0000 (15:29 +0100)]
Major CFI-FLASH driver update:
* Add env-variable "unlock" to handle initial state of sectors
(locked/unlocked).
Only the U-Boot image and it's environment is protected,
all other sectors are unprotected (unlocked) if flash
hardware protection is used (CFG_FLASH_PROTECTION) and
the environment variable "unlock" is set to "yes".
Patch by Stefan Roese, 28 Feb 2006
* Update drivers/cfi_flash.c:
- find_sector() called in both versions of flash_write_cfiword()
Patch by Peter Pearse, 27th Feb 2006
* CFI support for a x8/x16 AMD/Spansion flash configured in x8 mode
Patch by Jose Maria Lopez, 16 Jan 2006
* Add support for AMD/Spansion Flashes in flash_write_cfibuffer
Patch by Alex Bastos and Thomas Schaefer, 2005-08-29
* Changes/fixes for drivers/cfi_flash.c:
We *should* check if there are any error bits if the previous call
returned ERR_OK (Otherwise we will have output an error message in
flash_status_check() already.) The original code would only check for
error bits if flash_status_check() returns ERR_TIMEOUT.
Patch by Marcus Hall, 23 Aug 2005
* Changes/fixes for drivers/cfi_flash.c:
- Add CFG_FLASH_PROTECT_CLEAR on drivers/cfi_flash.c
- Prohibit buffer write when buffer_size is 1 on drivers/cfi_flash.c
Patch by Sangmoon Kim, 19 Aug 2005
* Fixes for drivers/cfi_flash.c:
- Fix wrong timeout value usage in flash_status_check()
- Round write_tout up when converting to msec in flash_get_size()
- Remove clearing flash status at the end of flash_write_cfibuffer()
which sets Intel 28F640J3 flash back to command mode on CSB472
Patch by Tolunay Orkun, 02 July 2005
Wolfgang Denk [Tue, 21 Feb 2006 16:33:04 +0000 (17:33 +0100)]
Add GIT version information (commid ID) to untagged U-Boot versions
As done in the linux kernel, the U-Boot version (U_BOOT_VERSION)
of all unreleased (untagged) U-Boot images will be automatically
extended upon compiletime with a part of the GIT commit ID and
possibly with "dirty" if uncommited changes are detected.
Here an example for the resulting version:
"U-Boot 1.1.4-g3457ac18-dirty"
The version is now maintained in the toplevel Makefile and the
version headers are autogenerated.
projects / u-boot / log