git.sur5r.net Git - u-boot/blob - board/mini-box/picosam9g45/picosam9g45.c

   1 /*
   2  * Board functions for mini-box PICOSAM9G45 (AT91SAM9G45) based board
   3  * (C) Copyright 2015 Inter Act B.V.
   4  *
   5  * Based on:
   6  * U-Boot file: board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
   7  * (C) Copyright 2007-2008
   8  * Stelian Pop <stelian@popies.net>
   9  * Lead Tech Design <www.leadtechdesign.com>
  10  *
  11  * SPDX-License-Identifier:     GPL-2.0+
  12  */
  13
  14 #include <common.h>
  15 #include <asm/io.h>
  16 #include <asm/arch/clk.h>
  17 #include <asm/arch/at91sam9g45_matrix.h>
  18 #include <asm/arch/at91sam9_smc.h>
  19 #include <asm/arch/at91_common.h>
  20 #include <asm/arch/gpio.h>
  21 #include <asm/arch/clk.h>
  22 #include <lcd.h>
  23 #include <linux/mtd/rawnand.h>
  24 #include <atmel_lcdc.h>
  25 #include <atmel_mci.h>
  26 #if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
  27 #include <net.h>
  28 #endif
  29 #include <netdev.h>
  30 #include <asm/mach-types.h>
  31
  32 DECLARE_GLOBAL_DATA_PTR;
  33
  34 /* ------------------------------------------------------------------------- */
  35 /*
  36  * Miscelaneous platform dependent initialisations
  37  */
  38
  39 #if defined(CONFIG_SPL_BUILD)
  40 #include <spl.h>
  41
  42 void at91_spl_board_init(void)
  43 {
  44 #ifdef CONFIG_SYS_USE_MMC
  45         at91_mci_hw_init();
  46 #endif
  47 }
  48
  49 #include <asm/arch/atmel_mpddrc.h>
  50 static void ddr2_conf(struct atmel_mpddrc_config *ddr2)
  51 {
  52         ddr2->md = (ATMEL_MPDDRC_MD_DBW_16_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM);
  53
  54         ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 |
  55                     ATMEL_MPDDRC_CR_NR_ROW_14 |
  56                     ATMEL_MPDDRC_CR_DQMS_SHARED |
  57                     ATMEL_MPDDRC_CR_CAS_DDR_CAS3);
  58
  59         ddr2->rtr = 0x24b;
  60
  61         ddr2->tpr0 = (6 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET |/* 6*7.5 = 45 ns */
  62                       2 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET |/* 2*7.5 = 15 ns */
  63                       2 << ATMEL_MPDDRC_TPR0_TWR_OFFSET | /* 2*7.5 = 15 ns */
  64                       8 << ATMEL_MPDDRC_TPR0_TRC_OFFSET | /* 8*7.5 = 60 ns */
  65                       2 << ATMEL_MPDDRC_TPR0_TRP_OFFSET | /* 2*7.5 = 15 ns */
  66                       1 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET | /* 1*7.5= 7.5 ns*/
  67                       1 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET | /* 1 clk cycle */
  68                       2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET); /* 2 clk cycles */
  69
  70         ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET | /* 2*7.5 = 15 ns */
  71                       200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET |
  72                       16 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET |
  73                       14 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET);
  74
  75         ddr2->tpr2 = (1 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET |
  76                       0 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET |
  77                       7 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET |
  78                       2 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET);
  79 }
  80
  81 void mem_init(void)
  82 {
  83         struct at91_matrix *mat = (struct at91_matrix *)ATMEL_BASE_MATRIX;
  84         struct atmel_mpddrc_config ddr2;
  85         unsigned long csa;
  86
  87         ddr2_conf(&ddr2);
  88
  89         at91_system_clk_enable(AT91_PMC_DDR);
  90
  91         /* Chip select 1 is for DDR2/SDRAM */
  92         csa = readl(&mat->ebicsa);
  93         csa |= AT91_MATRIX_EBI_CS1A_SDRAMC;
  94         csa &= ~AT91_MATRIX_EBI_VDDIOMSEL_3_3V;
  95         writel(csa, &mat->ebicsa);
  96
  97         /* DDRAM2 Controller initialize */
  98         ddr2_init(ATMEL_BASE_DDRSDRC0, ATMEL_BASE_CS6, &ddr2);
  99         ddr2_init(ATMEL_BASE_DDRSDRC1, ATMEL_BASE_CS1, &ddr2);
 100 }
 101 #endif
 102
 103 #ifdef CONFIG_CMD_USB
 104 static void picosam9g45_usb_hw_init(void)
 105 {
 106         at91_periph_clk_enable(ATMEL_ID_PIODE);
 107
 108         at91_set_gpio_output(AT91_PIN_PD1, 0);
 109         at91_set_gpio_output(AT91_PIN_PD3, 0);
 110 }
 111 #endif
 112
 113 #ifdef CONFIG_MACB
 114 static void picosam9g45_macb_hw_init(void)
 115 {
 116         struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA;
 117
 118         at91_periph_clk_enable(ATMEL_ID_EMAC);
 119
 120         /*
 121          * Disable pull-up on:
 122          *      RXDV (PA15) => PHY normal mode (not Test mode)
 123          *      ERX0 (PA12) => PHY ADDR0
 124          *      ERX1 (PA13) => PHY ADDR1 => PHYADDR = 0x0
 125          *
 126          * PHY has internal pull-down
 127          */
 128         writel(pin_to_mask(AT91_PIN_PA15) |
 129                pin_to_mask(AT91_PIN_PA12) |
 130                pin_to_mask(AT91_PIN_PA13),
 131                &pioa->pudr);
 132
 133         at91_phy_reset();
 134
 135         /* Re-enable pull-up */
 136         writel(pin_to_mask(AT91_PIN_PA15) |
 137                pin_to_mask(AT91_PIN_PA12) |
 138                pin_to_mask(AT91_PIN_PA13),
 139                &pioa->puer);
 140
 141         /* And the pins. */
 142         at91_macb_hw_init();
 143 }
 144 #endif
 145
 146 #ifdef CONFIG_LCD
 147
 148 vidinfo_t panel_info = {
 149         .vl_col =               480,
 150         .vl_row =               272,
 151         .vl_clk =               9000000,
 152         .vl_sync =              ATMEL_LCDC_INVLINE_NORMAL |
 153                                 ATMEL_LCDC_INVFRAME_NORMAL,
 154         .vl_bpix =              3,
 155         .vl_tft =               1,
 156         .vl_hsync_len =         45,
 157         .vl_left_margin =       1,
 158         .vl_right_margin =      1,
 159         .vl_vsync_len =         1,
 160         .vl_upper_margin =      40,
 161         .vl_lower_margin =      1,
 162         .mmio =                 ATMEL_BASE_LCDC,
 163 };
 164
 165
 166 void lcd_enable(void)
 167 {
 168         at91_set_A_periph(AT91_PIN_PE6, 1);     /* power up */
 169 }
 170
 171 void lcd_disable(void)
 172 {
 173         at91_set_A_periph(AT91_PIN_PE6, 0);     /* power down */
 174 }
 175
 176 static void picosam9g45_lcd_hw_init(void)
 177 {
 178         at91_set_A_periph(AT91_PIN_PE0, 0);     /* LCDDPWR */
 179         at91_set_A_periph(AT91_PIN_PE2, 0);     /* LCDCC */
 180         at91_set_A_periph(AT91_PIN_PE3, 0);     /* LCDVSYNC */
 181         at91_set_A_periph(AT91_PIN_PE4, 0);     /* LCDHSYNC */
 182         at91_set_A_periph(AT91_PIN_PE5, 0);     /* LCDDOTCK */
 183
 184         at91_set_A_periph(AT91_PIN_PE7, 0);     /* LCDD0 */
 185         at91_set_A_periph(AT91_PIN_PE8, 0);     /* LCDD1 */
 186         at91_set_A_periph(AT91_PIN_PE9, 0);     /* LCDD2 */
 187         at91_set_A_periph(AT91_PIN_PE10, 0);    /* LCDD3 */
 188         at91_set_A_periph(AT91_PIN_PE11, 0);    /* LCDD4 */
 189         at91_set_A_periph(AT91_PIN_PE12, 0);    /* LCDD5 */
 190         at91_set_A_periph(AT91_PIN_PE13, 0);    /* LCDD6 */
 191         at91_set_A_periph(AT91_PIN_PE14, 0);    /* LCDD7 */
 192         at91_set_A_periph(AT91_PIN_PE15, 0);    /* LCDD8 */
 193         at91_set_A_periph(AT91_PIN_PE16, 0);    /* LCDD9 */
 194         at91_set_A_periph(AT91_PIN_PE17, 0);    /* LCDD10 */
 195         at91_set_A_periph(AT91_PIN_PE18, 0);    /* LCDD11 */
 196         at91_set_A_periph(AT91_PIN_PE19, 0);    /* LCDD12 */
 197         at91_set_B_periph(AT91_PIN_PE20, 0);    /* LCDD13 */
 198         at91_set_A_periph(AT91_PIN_PE21, 0);    /* LCDD14 */
 199         at91_set_A_periph(AT91_PIN_PE22, 0);    /* LCDD15 */
 200         at91_set_A_periph(AT91_PIN_PE23, 0);    /* LCDD16 */
 201         at91_set_A_periph(AT91_PIN_PE24, 0);    /* LCDD17 */
 202         at91_set_A_periph(AT91_PIN_PE25, 0);    /* LCDD18 */
 203         at91_set_A_periph(AT91_PIN_PE26, 0);    /* LCDD19 */
 204         at91_set_A_periph(AT91_PIN_PE27, 0);    /* LCDD20 */
 205         at91_set_B_periph(AT91_PIN_PE28, 0);    /* LCDD21 */
 206         at91_set_A_periph(AT91_PIN_PE29, 0);    /* LCDD22 */
 207         at91_set_A_periph(AT91_PIN_PE30, 0);    /* LCDD23 */
 208
 209         at91_periph_clk_enable(ATMEL_ID_LCDC);
 210
 211         gd->fb_base = CONFIG_AT91SAM9G45_LCD_BASE;
 212 }
 213
 214 #ifdef CONFIG_LCD_INFO
 215 #include <nand.h>
 216 #include <version.h>
 217
 218 void lcd_show_board_info(void)
 219 {
 220         ulong dram_size;
 221         int i;
 222         char temp[32];
 223
 224         lcd_printf("%s\n", U_BOOT_VERSION);
 225         lcd_printf("(C) 2015 Inter Act B.V.\n");
 226         lcd_printf("support@interact.nl\n");
 227         lcd_printf("%s CPU at %s MHz\n",
 228                    ATMEL_CPU_NAME,
 229                    strmhz(temp, get_cpu_clk_rate()));
 230
 231         dram_size = 0;
 232         for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
 233                 dram_size += gd->bd->bi_dram[i].size;
 234         lcd_printf("  %ld MB SDRAM\n", dram_size >> 20);
 235 }
 236 #endif /* CONFIG_LCD_INFO */
 237 #endif
 238
 239 #ifdef CONFIG_GENERIC_ATMEL_MCI
 240 int board_mmc_init(bd_t *bis)
 241 {
 242         at91_mci_hw_init();
 243
 244         return atmel_mci_init((void *)ATMEL_BASE_MCI0);
 245 }
 246 #endif
 247
 248 int board_early_init_f(void)
 249 {
 250         at91_seriald_hw_init();
 251         return 0;
 252 }
 253
 254 int board_init(void)
 255 {
 256         gd->bd->bi_arch_number = MACH_TYPE_PICOSAM9G45;
 257
 258         /* adress of boot parameters */
 259         gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
 260
 261 #ifdef CONFIG_CMD_USB
 262         picosam9g45_usb_hw_init();
 263 #endif
 264 #ifdef CONFIG_ATMEL_SPI
 265         at91_spi0_hw_init(1 << 4);
 266 #endif
 267 #ifdef CONFIG_MACB
 268         picosam9g45_macb_hw_init();
 269 #endif
 270 #ifdef CONFIG_LCD
 271         picosam9g45_lcd_hw_init();
 272 #endif
 273         return 0;
 274 }
 275
 276 int dram_init(void)
 277 {
 278         gd->ram_size    = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE)
 279                         + get_ram_size((long *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE);
 280
 281         return 0;
 282 }
 283
 284 int dram_init_banksize(void)
 285 {
 286         gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
 287         gd->bd->bi_dram[0].size = get_ram_size((long *)PHYS_SDRAM_1,
 288                                                         PHYS_SDRAM_1_SIZE);
 289         gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
 290         gd->bd->bi_dram[1].size = get_ram_size((long *)PHYS_SDRAM_2,
 291                                                         PHYS_SDRAM_2_SIZE);
 292
 293         return 0;
 294 }
 295
 296 #ifdef CONFIG_RESET_PHY_R
 297 void reset_phy(void)
 298 {
 299 }
 300 #endif
 301
 302 int board_eth_init(bd_t *bis)
 303 {
 304         int rc = 0;
 305 #ifdef CONFIG_MACB
 306         rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x00);
 307 #endif
 308         return rc;
 309 }
 310
 311 /* SPI chip select control */
 312 #ifdef CONFIG_ATMEL_SPI
 313 #include <spi.h>
 314
 315 int spi_cs_is_valid(unsigned int bus, unsigned int cs)
 316 {
 317         return bus == 0 && cs < 2;
 318 }
 319
 320 void spi_cs_activate(struct spi_slave *slave)
 321 {
 322         switch (slave->cs) {
 323         case 1:
 324                 at91_set_gpio_output(AT91_PIN_PB18, 0);
 325                 break;
 326         case 0:
 327         default:
 328                 at91_set_gpio_output(AT91_PIN_PB3, 0);
 329                 break;
 330         }
 331 }
 332
 333 void spi_cs_deactivate(struct spi_slave *slave)
 334 {
 335         switch (slave->cs) {
 336         case 1:
 337                 at91_set_gpio_output(AT91_PIN_PB18, 1);
 338                 break;
 339         case 0:
 340         default:
 341                 at91_set_gpio_output(AT91_PIN_PB3, 1);
 342         break;
 343         }
 344 }
 345 #endif /* CONFIG_ATMEL_SPI */