git.sur5r.net Git - u-boot/blob - drivers/ddr/fsl/fsl_ddr_gen4.c

   1 /*
   2  * Copyright 2014-2015 Freescale Semiconductor, Inc.
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 #include <common.h>
   8 #include <asm/io.h>
   9 #include <fsl_ddr_sdram.h>
  10 #include <asm/processor.h>
  11 #include <fsl_immap.h>
  12 #include <fsl_ddr.h>
  13 #include <fsl_errata.h>
  14 #if defined(CONFIG_FSL_LSCH2) || defined(CONFIG_FSL_LSCH3) || \
  15         defined(CONFIG_ARM)
  16 #include <asm/arch/clock.h>
  17 #endif
  18
  19 #if defined(CONFIG_SYS_FSL_ERRATUM_A008511) | \
  20         defined(CONFIG_SYS_FSL_ERRATUM_A009803)
  21 static void set_wait_for_bits_clear(void *ptr, u32 value, u32 bits)
  22 {
  23         int timeout = 1000;
  24
  25         ddr_out32(ptr, value);
  26
  27         while (ddr_in32(ptr) & bits) {
  28                 udelay(100);
  29                 timeout--;
  30         }
  31         if (timeout <= 0)
  32                 puts("Error: wait for clear timeout.\n");
  33 }
  34 #endif
  35
  36 #if (CONFIG_CHIP_SELECTS_PER_CTRL > 4)
  37 #error Invalid setting for CONFIG_CHIP_SELECTS_PER_CTRL
  38 #endif
  39
  40 /*
  41  * regs has the to-be-set values for DDR controller registers
  42  * ctrl_num is the DDR controller number
  43  * step: 0 goes through the initialization in one pass
  44  *       1 sets registers and returns before enabling controller
  45  *       2 resumes from step 1 and continues to initialize
  46  * Dividing the initialization to two steps to deassert DDR reset signal
  47  * to comply with JEDEC specs for RDIMMs.
  48  */
  49 void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
  50                              unsigned int ctrl_num, int step)
  51 {
  52         unsigned int i, bus_width;
  53         struct ccsr_ddr __iomem *ddr;
  54         u32 temp32;
  55         u32 total_gb_size_per_controller;
  56         int timeout;
  57
  58 #ifdef CONFIG_SYS_FSL_ERRATUM_A008511
  59         u32 mr6;
  60         u32 vref_seq1[3] = {0x80, 0x96, 0x16};  /* for range 1 */
  61         u32 vref_seq2[3] = {0xc0, 0xf0, 0x70};  /* for range 2 */
  62         u32 *vref_seq = vref_seq1;
  63 #endif
  64 #ifdef CONFIG_FSL_DDR_BIST
  65         u32 mtcr, err_detect, err_sbe;
  66         u32 cs0_bnds, cs1_bnds, cs2_bnds, cs3_bnds, cs0_config;
  67 #endif
  68 #ifdef CONFIG_FSL_DDR_BIST
  69         char buffer[CONFIG_SYS_CBSIZE];
  70 #endif
  71         switch (ctrl_num) {
  72         case 0:
  73                 ddr = (void *)CONFIG_SYS_FSL_DDR_ADDR;
  74                 break;
  75 #if defined(CONFIG_SYS_FSL_DDR2_ADDR) && (CONFIG_SYS_NUM_DDR_CTLRS > 1)
  76         case 1:
  77                 ddr = (void *)CONFIG_SYS_FSL_DDR2_ADDR;
  78                 break;
  79 #endif
  80 #if defined(CONFIG_SYS_FSL_DDR3_ADDR) && (CONFIG_SYS_NUM_DDR_CTLRS > 2)
  81         case 2:
  82                 ddr = (void *)CONFIG_SYS_FSL_DDR3_ADDR;
  83                 break;
  84 #endif
  85 #if defined(CONFIG_SYS_FSL_DDR4_ADDR) && (CONFIG_SYS_NUM_DDR_CTLRS > 3)
  86         case 3:
  87                 ddr = (void *)CONFIG_SYS_FSL_DDR4_ADDR;
  88                 break;
  89 #endif
  90         default:
  91                 printf("%s unexpected ctrl_num = %u\n", __func__, ctrl_num);
  92                 return;
  93         }
  94
  95         if (step == 2)
  96                 goto step2;
  97
  98         if (regs->ddr_eor)
  99                 ddr_out32(&ddr->eor, regs->ddr_eor);
 100
 101         ddr_out32(&ddr->sdram_clk_cntl, regs->ddr_sdram_clk_cntl);
 102
 103         for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
 104                 if (i == 0) {
 105                         ddr_out32(&ddr->cs0_bnds, regs->cs[i].bnds);
 106                         ddr_out32(&ddr->cs0_config, regs->cs[i].config);
 107                         ddr_out32(&ddr->cs0_config_2, regs->cs[i].config_2);
 108
 109                 } else if (i == 1) {
 110                         ddr_out32(&ddr->cs1_bnds, regs->cs[i].bnds);
 111                         ddr_out32(&ddr->cs1_config, regs->cs[i].config);
 112                         ddr_out32(&ddr->cs1_config_2, regs->cs[i].config_2);
 113
 114                 } else if (i == 2) {
 115                         ddr_out32(&ddr->cs2_bnds, regs->cs[i].bnds);
 116                         ddr_out32(&ddr->cs2_config, regs->cs[i].config);
 117                         ddr_out32(&ddr->cs2_config_2, regs->cs[i].config_2);
 118
 119                 } else if (i == 3) {
 120                         ddr_out32(&ddr->cs3_bnds, regs->cs[i].bnds);
 121                         ddr_out32(&ddr->cs3_config, regs->cs[i].config);
 122                         ddr_out32(&ddr->cs3_config_2, regs->cs[i].config_2);
 123                 }
 124         }
 125
 126         ddr_out32(&ddr->timing_cfg_3, regs->timing_cfg_3);
 127         ddr_out32(&ddr->timing_cfg_0, regs->timing_cfg_0);
 128         ddr_out32(&ddr->timing_cfg_1, regs->timing_cfg_1);
 129         ddr_out32(&ddr->timing_cfg_2, regs->timing_cfg_2);
 130         ddr_out32(&ddr->timing_cfg_4, regs->timing_cfg_4);
 131         ddr_out32(&ddr->timing_cfg_5, regs->timing_cfg_5);
 132         ddr_out32(&ddr->timing_cfg_6, regs->timing_cfg_6);
 133         ddr_out32(&ddr->timing_cfg_7, regs->timing_cfg_7);
 134         ddr_out32(&ddr->timing_cfg_8, regs->timing_cfg_8);
 135         ddr_out32(&ddr->timing_cfg_9, regs->timing_cfg_9);
 136         ddr_out32(&ddr->ddr_zq_cntl, regs->ddr_zq_cntl);
 137         ddr_out32(&ddr->dq_map_0, regs->dq_map_0);
 138         ddr_out32(&ddr->dq_map_1, regs->dq_map_1);
 139         ddr_out32(&ddr->dq_map_2, regs->dq_map_2);
 140         ddr_out32(&ddr->dq_map_3, regs->dq_map_3);
 141         ddr_out32(&ddr->sdram_cfg_3, regs->ddr_sdram_cfg_3);
 142         ddr_out32(&ddr->sdram_mode, regs->ddr_sdram_mode);
 143         ddr_out32(&ddr->sdram_mode_2, regs->ddr_sdram_mode_2);
 144         ddr_out32(&ddr->sdram_mode_3, regs->ddr_sdram_mode_3);
 145         ddr_out32(&ddr->sdram_mode_4, regs->ddr_sdram_mode_4);
 146         ddr_out32(&ddr->sdram_mode_5, regs->ddr_sdram_mode_5);
 147         ddr_out32(&ddr->sdram_mode_6, regs->ddr_sdram_mode_6);
 148         ddr_out32(&ddr->sdram_mode_7, regs->ddr_sdram_mode_7);
 149         ddr_out32(&ddr->sdram_mode_8, regs->ddr_sdram_mode_8);
 150         ddr_out32(&ddr->sdram_mode_9, regs->ddr_sdram_mode_9);
 151         ddr_out32(&ddr->sdram_mode_10, regs->ddr_sdram_mode_10);
 152         ddr_out32(&ddr->sdram_mode_11, regs->ddr_sdram_mode_11);
 153         ddr_out32(&ddr->sdram_mode_12, regs->ddr_sdram_mode_12);
 154         ddr_out32(&ddr->sdram_mode_13, regs->ddr_sdram_mode_13);
 155         ddr_out32(&ddr->sdram_mode_14, regs->ddr_sdram_mode_14);
 156         ddr_out32(&ddr->sdram_mode_15, regs->ddr_sdram_mode_15);
 157         ddr_out32(&ddr->sdram_mode_16, regs->ddr_sdram_mode_16);
 158         ddr_out32(&ddr->sdram_md_cntl, regs->ddr_sdram_md_cntl);
 159 #ifdef CONFIG_SYS_FSL_ERRATUM_A009663
 160         ddr_out32(&ddr->sdram_interval,
 161                   regs->ddr_sdram_interval & ~SDRAM_INTERVAL_BSTOPRE);
 162 #else
 163         ddr_out32(&ddr->sdram_interval, regs->ddr_sdram_interval);
 164 #endif
 165         ddr_out32(&ddr->sdram_data_init, regs->ddr_data_init);
 166         ddr_out32(&ddr->ddr_wrlvl_cntl, regs->ddr_wrlvl_cntl);
 167 #ifndef CONFIG_SYS_FSL_DDR_EMU
 168         /*
 169          * Skip these two registers if running on emulator
 170          * because emulator doesn't have skew between bytes.
 171          */
 172
 173         if (regs->ddr_wrlvl_cntl_2)
 174                 ddr_out32(&ddr->ddr_wrlvl_cntl_2, regs->ddr_wrlvl_cntl_2);
 175         if (regs->ddr_wrlvl_cntl_3)
 176                 ddr_out32(&ddr->ddr_wrlvl_cntl_3, regs->ddr_wrlvl_cntl_3);
 177 #endif
 178
 179         ddr_out32(&ddr->ddr_sr_cntr, regs->ddr_sr_cntr);
 180         ddr_out32(&ddr->ddr_sdram_rcw_1, regs->ddr_sdram_rcw_1);
 181         ddr_out32(&ddr->ddr_sdram_rcw_2, regs->ddr_sdram_rcw_2);
 182         ddr_out32(&ddr->ddr_sdram_rcw_3, regs->ddr_sdram_rcw_3);
 183         ddr_out32(&ddr->ddr_sdram_rcw_4, regs->ddr_sdram_rcw_4);
 184         ddr_out32(&ddr->ddr_sdram_rcw_5, regs->ddr_sdram_rcw_5);
 185         ddr_out32(&ddr->ddr_sdram_rcw_6, regs->ddr_sdram_rcw_6);
 186         ddr_out32(&ddr->ddr_cdr1, regs->ddr_cdr1);
 187 #ifdef CONFIG_DEEP_SLEEP
 188         if (is_warm_boot()) {
 189                 ddr_out32(&ddr->sdram_cfg_2,
 190                           regs->ddr_sdram_cfg_2 & ~SDRAM_CFG2_D_INIT);
 191                 ddr_out32(&ddr->init_addr, CONFIG_SYS_SDRAM_BASE);
 192                 ddr_out32(&ddr->init_ext_addr, DDR_INIT_ADDR_EXT_UIA);
 193
 194                 /* DRAM VRef will not be trained */
 195                 ddr_out32(&ddr->ddr_cdr2,
 196                           regs->ddr_cdr2 & ~DDR_CDR2_VREF_TRAIN_EN);
 197         } else
 198 #endif
 199         {
 200                 ddr_out32(&ddr->sdram_cfg_2, regs->ddr_sdram_cfg_2);
 201                 ddr_out32(&ddr->init_addr, regs->ddr_init_addr);
 202                 ddr_out32(&ddr->init_ext_addr, regs->ddr_init_ext_addr);
 203                 ddr_out32(&ddr->ddr_cdr2, regs->ddr_cdr2);
 204         }
 205
 206 #ifdef CONFIG_SYS_FSL_ERRATUM_A009803
 207         /* part 1 of 2 */
 208         if (regs->ddr_sdram_cfg_2 & SDRAM_CFG2_AP_EN) {
 209                 if (regs->ddr_sdram_cfg & SDRAM_CFG_RD_EN) { /* for RDIMM */
 210                         ddr_out32(&ddr->ddr_sdram_rcw_2,
 211                                   regs->ddr_sdram_rcw_2 & ~0x0f000000);
 212                 }
 213                 ddr_out32(&ddr->err_disable, regs->err_disable |
 214                           DDR_ERR_DISABLE_APED);
 215         }
 216 #else
 217         ddr_out32(&ddr->err_disable, regs->err_disable);
 218 #endif
 219         ddr_out32(&ddr->err_int_en, regs->err_int_en);
 220         for (i = 0; i < 64; i++) {
 221                 if (regs->debug[i]) {
 222                         debug("Write to debug_%d as %08x\n",
 223                               i+1, regs->debug[i]);
 224                         ddr_out32(&ddr->debug[i], regs->debug[i]);
 225                 }
 226         }
 227
 228 #ifdef CONFIG_SYS_FSL_ERRATUM_A008511
 229         /* Part 1 of 2 */
 230         if (fsl_ddr_get_version(ctrl_num) == 0x50200) {
 231                 /* Disable DRAM VRef training */
 232                 ddr_out32(&ddr->ddr_cdr2,
 233                           regs->ddr_cdr2 & ~DDR_CDR2_VREF_TRAIN_EN);
 234                 /* disable transmit bit deskew */
 235                 temp32 = ddr_in32(&ddr->debug[28]);
 236                 temp32 |= DDR_TX_BD_DIS;
 237                 ddr_out32(&ddr->debug[28], temp32);
 238                 ddr_out32(&ddr->debug[25], 0x9000);
 239         } else if (fsl_ddr_get_version(ctrl_num) == 0x50201) {
 240                 /* Output enable forced off */
 241                 ddr_out32(&ddr->debug[37], 1 << 31);
 242                 /* Enable Vref training */
 243                 ddr_out32(&ddr->ddr_cdr2,
 244                           regs->ddr_cdr2 | DDR_CDR2_VREF_TRAIN_EN);
 245         } else {
 246                 debug("Erratum A008511 doesn't apply.\n");
 247         }
 248 #endif
 249
 250 #if defined(CONFIG_SYS_FSL_ERRATUM_A009803) || \
 251         defined(CONFIG_SYS_FSL_ERRATUM_A008511)
 252         /* Disable D_INIT */
 253         ddr_out32(&ddr->sdram_cfg_2,
 254                   regs->ddr_sdram_cfg_2 & ~SDRAM_CFG2_D_INIT);
 255 #endif
 256
 257 #ifdef CONFIG_SYS_FSL_ERRATUM_A009801
 258         temp32 = ddr_in32(&ddr->debug[25]);
 259         temp32 &= ~DDR_CAS_TO_PRE_SUB_MASK;
 260         temp32 |= 9 << DDR_CAS_TO_PRE_SUB_SHIFT;
 261         ddr_out32(&ddr->debug[25], temp32);
 262 #endif
 263
 264 #ifdef CONFIG_SYS_FSL_ERRATUM_A010165
 265         temp32 = get_ddr_freq(ctrl_num) / 1000000;
 266         if ((temp32 > 1900) && (temp32 < 2300)) {
 267                 temp32 = ddr_in32(&ddr->debug[28]);
 268                 ddr_out32(&ddr->debug[28], temp32 | 0x000a0000);
 269         }
 270 #endif
 271         /*
 272          * For RDIMMs, JEDEC spec requires clocks to be stable before reset is
 273          * deasserted. Clocks start when any chip select is enabled and clock
 274          * control register is set. Because all DDR components are connected to
 275          * one reset signal, this needs to be done in two steps. Step 1 is to
 276          * get the clocks started. Step 2 resumes after reset signal is
 277          * deasserted.
 278          */
 279         if (step == 1) {
 280                 udelay(200);
 281                 return;
 282         }
 283
 284 step2:
 285         /* Set, but do not enable the memory */
 286         temp32 = regs->ddr_sdram_cfg;
 287         temp32 &= ~(SDRAM_CFG_MEM_EN);
 288         ddr_out32(&ddr->sdram_cfg, temp32);
 289
 290         /*
 291          * 500 painful micro-seconds must elapse between
 292          * the DDR clock setup and the DDR config enable.
 293          * DDR2 need 200 us, and DDR3 need 500 us from spec,
 294          * we choose the max, that is 500 us for all of case.
 295          */
 296         udelay(500);
 297         mb();
 298         isb();
 299
 300 #ifdef CONFIG_DEEP_SLEEP
 301         if (is_warm_boot()) {
 302                 /* enter self-refresh */
 303                 temp32 = ddr_in32(&ddr->sdram_cfg_2);
 304                 temp32 |= SDRAM_CFG2_FRC_SR;
 305                 ddr_out32(&ddr->sdram_cfg_2, temp32);
 306                 /* do board specific memory setup */
 307                 board_mem_sleep_setup();
 308
 309                 temp32 = (ddr_in32(&ddr->sdram_cfg) | SDRAM_CFG_BI);
 310         } else
 311 #endif
 312                 temp32 = ddr_in32(&ddr->sdram_cfg) & ~SDRAM_CFG_BI;
 313         /* Let the controller go */
 314         ddr_out32(&ddr->sdram_cfg, temp32 | SDRAM_CFG_MEM_EN);
 315         mb();
 316         isb();
 317
 318 #if defined(CONFIG_SYS_FSL_ERRATUM_A008511) || \
 319         defined(CONFIG_SYS_FSL_ERRATUM_A009803)
 320         /* Part 2 of 2 */
 321         timeout = 40;
 322         /* Wait for idle. D_INIT needs to be cleared earlier, or timeout */
 323         while (!(ddr_in32(&ddr->debug[1]) & 0x2) &&
 324                (timeout > 0)) {
 325                 udelay(1000);
 326                 timeout--;
 327         }
 328         if (timeout <= 0) {
 329                 printf("Controler %d timeout, debug_2 = %x\n",
 330                        ctrl_num, ddr_in32(&ddr->debug[1]));
 331         }
 332
 333 #ifdef CONFIG_SYS_FSL_ERRATUM_A008511
 334         /* This erraum only applies to verion 5.2.0 */
 335         if (fsl_ddr_get_version(ctrl_num) == 0x50200) {
 336                 /* The vref setting sequence is different for range 2 */
 337                 if (regs->ddr_cdr2 & DDR_CDR2_VREF_RANGE_2)
 338                         vref_seq = vref_seq2;
 339
 340                 /* Set VREF */
 341                 for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
 342                         if (!(regs->cs[i].config & SDRAM_CS_CONFIG_EN))
 343                                 continue;
 344
 345                         mr6 = (regs->ddr_sdram_mode_10 >> 16)           |
 346                                  MD_CNTL_MD_EN                          |
 347                                  MD_CNTL_CS_SEL(i)                      |
 348                                  MD_CNTL_MD_SEL(6)                      |
 349                                  0x00200000;
 350                         temp32 = mr6 | vref_seq[0];
 351                         set_wait_for_bits_clear(&ddr->sdram_md_cntl,
 352                                                 temp32, MD_CNTL_MD_EN);
 353                         udelay(1);
 354                         debug("MR6 = 0x%08x\n", temp32);
 355                         temp32 = mr6 | vref_seq[1];
 356                         set_wait_for_bits_clear(&ddr->sdram_md_cntl,
 357                                                 temp32, MD_CNTL_MD_EN);
 358                         udelay(1);
 359                         debug("MR6 = 0x%08x\n", temp32);
 360                         temp32 = mr6 | vref_seq[2];
 361                         set_wait_for_bits_clear(&ddr->sdram_md_cntl,
 362                                                 temp32, MD_CNTL_MD_EN);
 363                         udelay(1);
 364                         debug("MR6 = 0x%08x\n", temp32);
 365                 }
 366                 ddr_out32(&ddr->sdram_md_cntl, 0);
 367                 temp32 = ddr_in32(&ddr->debug[28]);
 368                 temp32 &= ~DDR_TX_BD_DIS; /* Enable deskew */
 369                 ddr_out32(&ddr->debug[28], temp32);
 370                 ddr_out32(&ddr->debug[1], 0x400);       /* restart deskew */
 371                 /* wait for idle */
 372                 timeout = 40;
 373                 while (!(ddr_in32(&ddr->debug[1]) & 0x2) &&
 374                        (timeout > 0)) {
 375                         udelay(1000);
 376                         timeout--;
 377                 }
 378                 if (timeout <= 0) {
 379                         printf("Controler %d timeout, debug_2 = %x\n",
 380                                ctrl_num, ddr_in32(&ddr->debug[1]));
 381                 }
 382         }
 383 #endif /* CONFIG_SYS_FSL_ERRATUM_A008511 */
 384
 385 #ifdef CONFIG_SYS_FSL_ERRATUM_A009803
 386         if (regs->ddr_sdram_cfg_2 & SDRAM_CFG2_AP_EN) {
 387                 /* if it's RDIMM */
 388                 if (regs->ddr_sdram_cfg & SDRAM_CFG_RD_EN) {
 389                         for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
 390                                 if (!(regs->cs[i].config & SDRAM_CS_CONFIG_EN))
 391                                         continue;
 392                                 set_wait_for_bits_clear(&ddr->sdram_md_cntl,
 393                                                         MD_CNTL_MD_EN |
 394                                                         MD_CNTL_CS_SEL(i) |
 395                                                         0x070000ed,
 396                                                         MD_CNTL_MD_EN);
 397                                 udelay(1);
 398                         }
 399                 }
 400
 401                 ddr_out32(&ddr->err_disable,
 402                           regs->err_disable & ~DDR_ERR_DISABLE_APED);
 403         }
 404 #endif
 405         /* Restore D_INIT */
 406         ddr_out32(&ddr->sdram_cfg_2, regs->ddr_sdram_cfg_2);
 407 #endif
 408
 409         total_gb_size_per_controller = 0;
 410         for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
 411                 if (!(regs->cs[i].config & 0x80000000))
 412                         continue;
 413                 total_gb_size_per_controller += 1 << (
 414                         ((regs->cs[i].config >> 14) & 0x3) + 2 +
 415                         ((regs->cs[i].config >> 8) & 0x7) + 12 +
 416                         ((regs->cs[i].config >> 4) & 0x3) + 0 +
 417                         ((regs->cs[i].config >> 0) & 0x7) + 8 +
 418                         3 - ((regs->ddr_sdram_cfg >> 19) & 0x3) -
 419                         26);                    /* minus 26 (count of 64M) */
 420         }
 421         if (fsl_ddr_get_intl3r() & 0x80000000)  /* 3-way interleaving */
 422                 total_gb_size_per_controller *= 3;
 423         else if (regs->cs[0].config & 0x20000000) /* 2-way interleaving */
 424                 total_gb_size_per_controller <<= 1;
 425         /*
 426          * total memory / bus width = transactions needed
 427          * transactions needed / data rate = seconds
 428          * to add plenty of buffer, double the time
 429          * For example, 2GB on 666MT/s 64-bit bus takes about 402ms
 430          * Let's wait for 800ms
 431          */
 432         bus_width = 3 - ((ddr_in32(&ddr->sdram_cfg) & SDRAM_CFG_DBW_MASK)
 433                         >> SDRAM_CFG_DBW_SHIFT);
 434         timeout = ((total_gb_size_per_controller << (6 - bus_width)) * 100 /
 435                 (get_ddr_freq(ctrl_num) >> 20)) << 2;
 436         total_gb_size_per_controller >>= 4;     /* shift down to gb size */
 437         debug("total %d GB\n", total_gb_size_per_controller);
 438         debug("Need to wait up to %d * 10ms\n", timeout);
 439
 440         /* Poll DDR_SDRAM_CFG_2[D_INIT] bit until auto-data init is done.  */
 441         while ((ddr_in32(&ddr->sdram_cfg_2) & SDRAM_CFG2_D_INIT) &&
 442                 (timeout >= 0)) {
 443                 udelay(10000);          /* throttle polling rate */
 444                 timeout--;
 445         }
 446
 447         if (timeout <= 0)
 448                 printf("Waiting for D_INIT timeout. Memory may not work.\n");
 449
 450 #ifdef CONFIG_SYS_FSL_ERRATUM_A009663
 451         ddr_out32(&ddr->sdram_interval, regs->ddr_sdram_interval);
 452 #endif
 453
 454 #ifdef CONFIG_DEEP_SLEEP
 455         if (is_warm_boot()) {
 456                 /* exit self-refresh */
 457                 temp32 = ddr_in32(&ddr->sdram_cfg_2);
 458                 temp32 &= ~SDRAM_CFG2_FRC_SR;
 459                 ddr_out32(&ddr->sdram_cfg_2, temp32);
 460         }
 461 #endif
 462
 463 #ifdef CONFIG_FSL_DDR_BIST
 464 #define BIST_PATTERN1   0xFFFFFFFF
 465 #define BIST_PATTERN2   0x0
 466 #define BIST_CR         0x80010000
 467 #define BIST_CR_EN      0x80000000
 468 #define BIST_CR_STAT    0x00000001
 469 #define CTLR_INTLV_MASK 0x20000000
 470         /* Perform build-in test on memory. Three-way interleaving is not yet
 471          * supported by this code. */
 472         if (env_get_f("ddr_bist", buffer, CONFIG_SYS_CBSIZE) >= 0) {
 473                 puts("Running BIST test. This will take a while...");
 474                 cs0_config = ddr_in32(&ddr->cs0_config);
 475                 cs0_bnds = ddr_in32(&ddr->cs0_bnds);
 476                 cs1_bnds = ddr_in32(&ddr->cs1_bnds);
 477                 cs2_bnds = ddr_in32(&ddr->cs2_bnds);
 478                 cs3_bnds = ddr_in32(&ddr->cs3_bnds);
 479                 if (cs0_config & CTLR_INTLV_MASK) {
 480                         /* set bnds to non-interleaving */
 481                         ddr_out32(&ddr->cs0_bnds, (cs0_bnds & 0xfffefffe) >> 1);
 482                         ddr_out32(&ddr->cs1_bnds, (cs1_bnds & 0xfffefffe) >> 1);
 483                         ddr_out32(&ddr->cs2_bnds, (cs2_bnds & 0xfffefffe) >> 1);
 484                         ddr_out32(&ddr->cs3_bnds, (cs3_bnds & 0xfffefffe) >> 1);
 485                 }
 486                 ddr_out32(&ddr->mtp1, BIST_PATTERN1);
 487                 ddr_out32(&ddr->mtp2, BIST_PATTERN1);
 488                 ddr_out32(&ddr->mtp3, BIST_PATTERN2);
 489                 ddr_out32(&ddr->mtp4, BIST_PATTERN2);
 490                 ddr_out32(&ddr->mtp5, BIST_PATTERN1);
 491                 ddr_out32(&ddr->mtp6, BIST_PATTERN1);
 492                 ddr_out32(&ddr->mtp7, BIST_PATTERN2);
 493                 ddr_out32(&ddr->mtp8, BIST_PATTERN2);
 494                 ddr_out32(&ddr->mtp9, BIST_PATTERN1);
 495                 ddr_out32(&ddr->mtp10, BIST_PATTERN2);
 496                 mtcr = BIST_CR;
 497                 ddr_out32(&ddr->mtcr, mtcr);
 498                 timeout = 100;
 499                 while (timeout > 0 && (mtcr & BIST_CR_EN)) {
 500                         mdelay(1000);
 501                         timeout--;
 502                         mtcr = ddr_in32(&ddr->mtcr);
 503                 }
 504                 if (timeout <= 0)
 505                         puts("Timeout\n");
 506                 else
 507                         puts("Done\n");
 508                 err_detect = ddr_in32(&ddr->err_detect);
 509                 err_sbe = ddr_in32(&ddr->err_sbe);
 510                 if (mtcr & BIST_CR_STAT) {
 511                         printf("BIST test failed on controller %d.\n",
 512                                ctrl_num);
 513                 }
 514                 if (err_detect || (err_sbe & 0xffff)) {
 515                         printf("ECC error detected on controller %d.\n",
 516                                ctrl_num);
 517                 }
 518
 519                 if (cs0_config & CTLR_INTLV_MASK) {
 520                         /* restore bnds registers */
 521                         ddr_out32(&ddr->cs0_bnds, cs0_bnds);
 522                         ddr_out32(&ddr->cs1_bnds, cs1_bnds);
 523                         ddr_out32(&ddr->cs2_bnds, cs2_bnds);
 524                         ddr_out32(&ddr->cs3_bnds, cs3_bnds);
 525                 }
 526         }
 527 #endif
 528 }