git.sur5r.net Git - u-boot/blob - drivers/fpga/zynqpl.c

   1 /*
   2  * (C) Copyright 2012-2013, Xilinx, Michal Simek
   3  *
   4  * (C) Copyright 2012
   5  * Joe Hershberger <joe.hershberger@ni.com>
   6  *
   7  * SPDX-License-Identifier:     GPL-2.0+
   8  */
   9
  10 #include <common.h>
  11 #include <console.h>
  12 #include <asm/io.h>
  13 #include <fs.h>
  14 #include <zynqpl.h>
  15 #include <linux/sizes.h>
  16 #include <asm/arch/hardware.h>
  17 #include <asm/arch/sys_proto.h>
  18
  19 #define DEVCFG_CTRL_PCFG_PROG_B         0x40000000
  20 #define DEVCFG_CTRL_PCFG_AES_EFUSE_MASK 0x00001000
  21 #define DEVCFG_ISR_FATAL_ERROR_MASK     0x00740040
  22 #define DEVCFG_ISR_ERROR_FLAGS_MASK     0x00340840
  23 #define DEVCFG_ISR_RX_FIFO_OV           0x00040000
  24 #define DEVCFG_ISR_DMA_DONE             0x00002000
  25 #define DEVCFG_ISR_PCFG_DONE            0x00000004
  26 #define DEVCFG_STATUS_DMA_CMD_Q_F       0x80000000
  27 #define DEVCFG_STATUS_DMA_CMD_Q_E       0x40000000
  28 #define DEVCFG_STATUS_DMA_DONE_CNT_MASK 0x30000000
  29 #define DEVCFG_STATUS_PCFG_INIT         0x00000010
  30 #define DEVCFG_MCTRL_PCAP_LPBK          0x00000010
  31 #define DEVCFG_MCTRL_RFIFO_FLUSH        0x00000002
  32 #define DEVCFG_MCTRL_WFIFO_FLUSH        0x00000001
  33
  34 #ifndef CONFIG_SYS_FPGA_WAIT
  35 #define CONFIG_SYS_FPGA_WAIT CONFIG_SYS_HZ/100  /* 10 ms */
  36 #endif
  37
  38 #ifndef CONFIG_SYS_FPGA_PROG_TIME
  39 #define CONFIG_SYS_FPGA_PROG_TIME       (CONFIG_SYS_HZ * 4) /* 4 s */
  40 #endif
  41
  42 #define DUMMY_WORD      0xffffffff
  43
  44 /* Xilinx binary format header */
  45 static const u32 bin_format[] = {
  46         DUMMY_WORD, /* Dummy words */
  47         DUMMY_WORD,
  48         DUMMY_WORD,
  49         DUMMY_WORD,
  50         DUMMY_WORD,
  51         DUMMY_WORD,
  52         DUMMY_WORD,
  53         DUMMY_WORD,
  54         0x000000bb, /* Sync word */
  55         0x11220044, /* Sync word */
  56         DUMMY_WORD,
  57         DUMMY_WORD,
  58         0xaa995566, /* Sync word */
  59 };
  60
  61 #define SWAP_NO         1
  62 #define SWAP_DONE       2
  63
  64 /*
  65  * Load the whole word from unaligned buffer
  66  * Keep in your mind that it is byte loading on little-endian system
  67  */
  68 static u32 load_word(const void *buf, u32 swap)
  69 {
  70         u32 word = 0;
  71         u8 *bitc = (u8 *)buf;
  72         int p;
  73
  74         if (swap == SWAP_NO) {
  75                 for (p = 0; p < 4; p++) {
  76                         word <<= 8;
  77                         word |= bitc[p];
  78                 }
  79         } else {
  80                 for (p = 3; p >= 0; p--) {
  81                         word <<= 8;
  82                         word |= bitc[p];
  83                 }
  84         }
  85
  86         return word;
  87 }
  88
  89 static u32 check_header(const void *buf)
  90 {
  91         u32 i, pattern;
  92         int swap = SWAP_NO;
  93         u32 *test = (u32 *)buf;
  94
  95         debug("%s: Let's check bitstream header\n", __func__);
  96
  97         /* Checking that passing bin is not a bitstream */
  98         for (i = 0; i < ARRAY_SIZE(bin_format); i++) {
  99                 pattern = load_word(&test[i], swap);
 100
 101                 /*
 102                  * Bitstreams in binary format are swapped
 103                  * compare to regular bistream.
 104                  * Do not swap dummy word but if swap is done assume
 105                  * that parsing buffer is binary format
 106                  */
 107                 if ((__swab32(pattern) != DUMMY_WORD) &&
 108                     (__swab32(pattern) == bin_format[i])) {
 109                         pattern = __swab32(pattern);
 110                         swap = SWAP_DONE;
 111                         debug("%s: data swapped - let's swap\n", __func__);
 112                 }
 113
 114                 debug("%s: %d/%x: pattern %x/%x bin_format\n", __func__, i,
 115                       (u32)&test[i], pattern, bin_format[i]);
 116                 if (pattern != bin_format[i]) {
 117                         debug("%s: Bitstream is not recognized\n", __func__);
 118                         return 0;
 119                 }
 120         }
 121         debug("%s: Found bitstream header at %x %s swapinng\n", __func__,
 122               (u32)buf, swap == SWAP_NO ? "without" : "with");
 123
 124         return swap;
 125 }
 126
 127 static void *check_data(u8 *buf, size_t bsize, u32 *swap)
 128 {
 129         u32 word, p = 0; /* possition */
 130
 131         /* Because buf doesn't need to be aligned let's read it by chars */
 132         for (p = 0; p < bsize; p++) {
 133                 word = load_word(&buf[p], SWAP_NO);
 134                 debug("%s: word %x %x/%x\n", __func__, word, p, (u32)&buf[p]);
 135
 136                 /* Find the first bitstream dummy word */
 137                 if (word == DUMMY_WORD) {
 138                         debug("%s: Found dummy word at position %x/%x\n",
 139                               __func__, p, (u32)&buf[p]);
 140                         *swap = check_header(&buf[p]);
 141                         if (*swap) {
 142                                 /* FIXME add full bitstream checking here */
 143                                 return &buf[p];
 144                         }
 145                 }
 146                 /* Loop can be huge - support CTRL + C */
 147                 if (ctrlc())
 148                         return NULL;
 149         }
 150         return NULL;
 151 }
 152
 153 static int zynq_dma_transfer(u32 srcbuf, u32 srclen, u32 dstbuf, u32 dstlen)
 154 {
 155         unsigned long ts;
 156         u32 isr_status;
 157
 158         /* Set up the transfer */
 159         writel((u32)srcbuf, &devcfg_base->dma_src_addr);
 160         writel(dstbuf, &devcfg_base->dma_dst_addr);
 161         writel(srclen, &devcfg_base->dma_src_len);
 162         writel(dstlen, &devcfg_base->dma_dst_len);
 163
 164         isr_status = readl(&devcfg_base->int_sts);
 165
 166         /* Polling the PCAP_INIT status for Set */
 167         ts = get_timer(0);
 168         while (!(isr_status & DEVCFG_ISR_DMA_DONE)) {
 169                 if (isr_status & DEVCFG_ISR_ERROR_FLAGS_MASK) {
 170                         debug("%s: Error: isr = 0x%08X\n", __func__,
 171                               isr_status);
 172                         debug("%s: Write count = 0x%08X\n", __func__,
 173                               readl(&devcfg_base->write_count));
 174                         debug("%s: Read count = 0x%08X\n", __func__,
 175                               readl(&devcfg_base->read_count));
 176
 177                         return FPGA_FAIL;
 178                 }
 179                 if (get_timer(ts) > CONFIG_SYS_FPGA_PROG_TIME) {
 180                         printf("%s: Timeout wait for DMA to complete\n",
 181                                __func__);
 182                         return FPGA_FAIL;
 183                 }
 184                 isr_status = readl(&devcfg_base->int_sts);
 185         }
 186
 187         debug("%s: DMA transfer is done\n", __func__);
 188
 189         /* Clear out the DMA status */
 190         writel(DEVCFG_ISR_DMA_DONE, &devcfg_base->int_sts);
 191
 192         return FPGA_SUCCESS;
 193 }
 194
 195 static int zynq_dma_xfer_init(bitstream_type bstype)
 196 {
 197         u32 status, control, isr_status;
 198         unsigned long ts;
 199
 200         /* Clear loopback bit */
 201         clrbits_le32(&devcfg_base->mctrl, DEVCFG_MCTRL_PCAP_LPBK);
 202
 203         if (bstype != BIT_PARTIAL) {
 204                 zynq_slcr_devcfg_disable();
 205
 206                 /* Setting PCFG_PROG_B signal to high */
 207                 control = readl(&devcfg_base->ctrl);
 208                 writel(control | DEVCFG_CTRL_PCFG_PROG_B, &devcfg_base->ctrl);
 209
 210                 /*
 211                  * Delay is required if AES efuse is selected as
 212                  * key source.
 213                  */
 214                 if (control & DEVCFG_CTRL_PCFG_AES_EFUSE_MASK)
 215                         mdelay(5);
 216
 217                 /* Setting PCFG_PROG_B signal to low */
 218                 writel(control & ~DEVCFG_CTRL_PCFG_PROG_B, &devcfg_base->ctrl);
 219
 220                 /*
 221                  * Delay is required if AES efuse is selected as
 222                  * key source.
 223                  */
 224                 if (control & DEVCFG_CTRL_PCFG_AES_EFUSE_MASK)
 225                         mdelay(5);
 226
 227                 /* Polling the PCAP_INIT status for Reset */
 228                 ts = get_timer(0);
 229                 while (readl(&devcfg_base->status) & DEVCFG_STATUS_PCFG_INIT) {
 230                         if (get_timer(ts) > CONFIG_SYS_FPGA_WAIT) {
 231                                 printf("%s: Timeout wait for INIT to clear\n",
 232                                        __func__);
 233                                 return FPGA_FAIL;
 234                         }
 235                 }
 236
 237                 /* Setting PCFG_PROG_B signal to high */
 238                 writel(control | DEVCFG_CTRL_PCFG_PROG_B, &devcfg_base->ctrl);
 239
 240                 /* Polling the PCAP_INIT status for Set */
 241                 ts = get_timer(0);
 242                 while (!(readl(&devcfg_base->status) &
 243                         DEVCFG_STATUS_PCFG_INIT)) {
 244                         if (get_timer(ts) > CONFIG_SYS_FPGA_WAIT) {
 245                                 printf("%s: Timeout wait for INIT to set\n",
 246                                        __func__);
 247                                 return FPGA_FAIL;
 248                         }
 249                 }
 250         }
 251
 252         isr_status = readl(&devcfg_base->int_sts);
 253
 254         /* Clear it all, so if Boot ROM comes back, it can proceed */
 255         writel(0xFFFFFFFF, &devcfg_base->int_sts);
 256
 257         if (isr_status & DEVCFG_ISR_FATAL_ERROR_MASK) {
 258                 debug("%s: Fatal errors in PCAP 0x%X\n", __func__, isr_status);
 259
 260                 /* If RX FIFO overflow, need to flush RX FIFO first */
 261                 if (isr_status & DEVCFG_ISR_RX_FIFO_OV) {
 262                         writel(DEVCFG_MCTRL_RFIFO_FLUSH, &devcfg_base->mctrl);
 263                         writel(0xFFFFFFFF, &devcfg_base->int_sts);
 264                 }
 265                 return FPGA_FAIL;
 266         }
 267
 268         status = readl(&devcfg_base->status);
 269
 270         debug("%s: Status = 0x%08X\n", __func__, status);
 271
 272         if (status & DEVCFG_STATUS_DMA_CMD_Q_F) {
 273                 debug("%s: Error: device busy\n", __func__);
 274                 return FPGA_FAIL;
 275         }
 276
 277         debug("%s: Device ready\n", __func__);
 278
 279         if (!(status & DEVCFG_STATUS_DMA_CMD_Q_E)) {
 280                 if (!(readl(&devcfg_base->int_sts) & DEVCFG_ISR_DMA_DONE)) {
 281                         /* Error state, transfer cannot occur */
 282                         debug("%s: ISR indicates error\n", __func__);
 283                         return FPGA_FAIL;
 284                 } else {
 285                         /* Clear out the status */
 286                         writel(DEVCFG_ISR_DMA_DONE, &devcfg_base->int_sts);
 287                 }
 288         }
 289
 290         if (status & DEVCFG_STATUS_DMA_DONE_CNT_MASK) {
 291                 /* Clear the count of completed DMA transfers */
 292                 writel(DEVCFG_STATUS_DMA_DONE_CNT_MASK, &devcfg_base->status);
 293         }
 294
 295         return FPGA_SUCCESS;
 296 }
 297
 298 static u32 *zynq_align_dma_buffer(u32 *buf, u32 len, u32 swap)
 299 {
 300         u32 *new_buf;
 301         u32 i;
 302
 303         if ((u32)buf != ALIGN((u32)buf, ARCH_DMA_MINALIGN)) {
 304                 new_buf = (u32 *)ALIGN((u32)buf, ARCH_DMA_MINALIGN);
 305
 306                 /*
 307                  * This might be dangerous but permits to flash if
 308                  * ARCH_DMA_MINALIGN is greater than header size
 309                  */
 310                 if (new_buf > buf) {
 311                         debug("%s: Aligned buffer is after buffer start\n",
 312                               __func__);
 313                         new_buf -= ARCH_DMA_MINALIGN;
 314                 }
 315                 printf("%s: Align buffer at %x to %x(swap %d)\n", __func__,
 316                        (u32)buf, (u32)new_buf, swap);
 317
 318                 for (i = 0; i < (len/4); i++)
 319                         new_buf[i] = load_word(&buf[i], swap);
 320
 321                 buf = new_buf;
 322         } else if (swap != SWAP_DONE) {
 323                 /* For bitstream which are aligned */
 324                 u32 *new_buf = (u32 *)buf;
 325
 326                 printf("%s: Bitstream is not swapped(%d) - swap it\n", __func__,
 327                        swap);
 328
 329                 for (i = 0; i < (len/4); i++)
 330                         new_buf[i] = load_word(&buf[i], swap);
 331         }
 332
 333         return buf;
 334 }
 335
 336 static int zynq_validate_bitstream(xilinx_desc *desc, const void *buf,
 337                                    size_t bsize, u32 blocksize, u32 *swap,
 338                                    bitstream_type *bstype)
 339 {
 340         u32 *buf_start;
 341         u32 diff;
 342
 343         buf_start = check_data((u8 *)buf, blocksize, swap);
 344
 345         if (!buf_start)
 346                 return FPGA_FAIL;
 347
 348         /* Check if data is postpone from start */
 349         diff = (u32)buf_start - (u32)buf;
 350         if (diff) {
 351                 printf("%s: Bitstream is not validated yet (diff %x)\n",
 352                        __func__, diff);
 353                 return FPGA_FAIL;
 354         }
 355
 356         if ((u32)buf < SZ_1M) {
 357                 printf("%s: Bitstream has to be placed up to 1MB (%x)\n",
 358                        __func__, (u32)buf);
 359                 return FPGA_FAIL;
 360         }
 361
 362         if (zynq_dma_xfer_init(*bstype))
 363                 return FPGA_FAIL;
 364
 365         return 0;
 366 }
 367
 368 static int zynq_load(xilinx_desc *desc, const void *buf, size_t bsize,
 369                      bitstream_type bstype)
 370 {
 371         unsigned long ts; /* Timestamp */
 372         u32 isr_status, swap;
 373
 374         /*
 375          * send bsize inplace of blocksize as it was not a bitstream
 376          * in chunks
 377          */
 378         if (zynq_validate_bitstream(desc, buf, bsize, bsize, &swap,
 379                                     &bstype))
 380                 return FPGA_FAIL;
 381
 382         buf = zynq_align_dma_buffer((u32 *)buf, bsize, swap);
 383
 384         debug("%s: Source = 0x%08X\n", __func__, (u32)buf);
 385         debug("%s: Size = %zu\n", __func__, bsize);
 386
 387         /* flush(clean & invalidate) d-cache range buf */
 388         flush_dcache_range((u32)buf, (u32)buf +
 389                            roundup(bsize, ARCH_DMA_MINALIGN));
 390
 391         if (zynq_dma_transfer((u32)buf | 1, bsize >> 2, 0xffffffff, 0))
 392                 return FPGA_FAIL;
 393
 394         isr_status = readl(&devcfg_base->int_sts);
 395         /* Check FPGA configuration completion */
 396         ts = get_timer(0);
 397         while (!(isr_status & DEVCFG_ISR_PCFG_DONE)) {
 398                 if (get_timer(ts) > CONFIG_SYS_FPGA_WAIT) {
 399                         printf("%s: Timeout wait for FPGA to config\n",
 400                                __func__);
 401                         return FPGA_FAIL;
 402                 }
 403                 isr_status = readl(&devcfg_base->int_sts);
 404         }
 405
 406         debug("%s: FPGA config done\n", __func__);
 407
 408         if (bstype != BIT_PARTIAL)
 409                 zynq_slcr_devcfg_enable();
 410
 411         return FPGA_SUCCESS;
 412 }
 413
 414 #if defined(CONFIG_CMD_FPGA_LOADFS)
 415 static int zynq_loadfs(xilinx_desc *desc, const void *buf, size_t bsize,
 416                        fpga_fs_info *fsinfo)
 417 {
 418         unsigned long ts; /* Timestamp */
 419         u32 isr_status, swap;
 420         u32 partialbit = 0;
 421         loff_t blocksize, actread;
 422         loff_t pos = 0;
 423         int fstype;
 424         char *interface, *dev_part, *filename;
 425
 426         blocksize = fsinfo->blocksize;
 427         interface = fsinfo->interface;
 428         dev_part = fsinfo->dev_part;
 429         filename = fsinfo->filename;
 430         fstype = fsinfo->fstype;
 431
 432         if (fs_set_blk_dev(interface, dev_part, fstype))
 433                 return FPGA_FAIL;
 434
 435         if (fs_read(filename, (u32) buf, pos, blocksize, &actread) < 0)
 436                 return FPGA_FAIL;
 437
 438         if (zynq_validate_bitstream(desc, buf, bsize, blocksize, &swap,
 439                                     &partialbit))
 440                 return FPGA_FAIL;
 441
 442         dcache_disable();
 443
 444         do {
 445                 buf = zynq_align_dma_buffer((u32 *)buf, blocksize, swap);
 446
 447                 if (zynq_dma_transfer((u32)buf | 1, blocksize >> 2,
 448                                       0xffffffff, 0))
 449                         return FPGA_FAIL;
 450
 451                 bsize -= blocksize;
 452                 pos   += blocksize;
 453
 454                 if (fs_set_blk_dev(interface, dev_part, fstype))
 455                         return FPGA_FAIL;
 456
 457                 if (bsize > blocksize) {
 458                         if (fs_read(filename, (u32) buf, pos, blocksize, &actread) < 0)
 459                                 return FPGA_FAIL;
 460                 } else {
 461                         if (fs_read(filename, (u32) buf, pos, bsize, &actread) < 0)
 462                                 return FPGA_FAIL;
 463                 }
 464         } while (bsize > blocksize);
 465
 466         buf = zynq_align_dma_buffer((u32 *)buf, blocksize, swap);
 467
 468         if (zynq_dma_transfer((u32)buf | 1, bsize >> 2, 0xffffffff, 0))
 469                 return FPGA_FAIL;
 470
 471         dcache_enable();
 472
 473         isr_status = readl(&devcfg_base->int_sts);
 474
 475         /* Check FPGA configuration completion */
 476         ts = get_timer(0);
 477         while (!(isr_status & DEVCFG_ISR_PCFG_DONE)) {
 478                 if (get_timer(ts) > CONFIG_SYS_FPGA_WAIT) {
 479                         printf("%s: Timeout wait for FPGA to config\n",
 480                                __func__);
 481                         return FPGA_FAIL;
 482                 }
 483                 isr_status = readl(&devcfg_base->int_sts);
 484         }
 485
 486         debug("%s: FPGA config done\n", __func__);
 487
 488         if (!partialbit)
 489                 zynq_slcr_devcfg_enable();
 490
 491         return FPGA_SUCCESS;
 492 }
 493 #endif
 494
 495 struct xilinx_fpga_op zynq_op = {
 496         .load = zynq_load,
 497 #if defined(CONFIG_CMD_FPGA_LOADFS)
 498         .loadfs = zynq_loadfs,
 499 #endif
 500 };