]> git.sur5r.net Git - u-boot/blob - drivers/spi/bcmstb_spi.c
board: arm: Add support for Broadcom BCM7445
[u-boot] / drivers / spi / bcmstb_spi.c
1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3  * (C) Copyright 2018  Cisco Systems, Inc.
4  *
5  * Author: Thomas Fitzsimmons <fitzsim@fitzsim.org>
6  */
7
8 #include <asm/io.h>
9 #include <command.h>
10 #include <config.h>
11 #include <dm.h>
12 #include <errno.h>
13 #include <fdtdec.h>
14 #include <linux/bitops.h>
15 #include <linux/delay.h>
16 #include <log.h>
17 #include <malloc.h>
18 #include <spi.h>
19 #include <time.h>
20
21 DECLARE_GLOBAL_DATA_PTR;
22
23 #define SPBR_MIN                8
24 #define BITS_PER_WORD           8
25
26 #define NUM_TXRAM               32
27 #define NUM_RXRAM               32
28 #define NUM_CDRAM               16
29
30 /* hif_mspi register structure. */
31 struct bcmstb_hif_mspi_regs {
32         u32 spcr0_lsb;          /* 0x000 */
33         u32 spcr0_msb;          /* 0x004 */
34         u32 spcr1_lsb;          /* 0x008 */
35         u32 spcr1_msb;          /* 0x00c */
36         u32 newqp;              /* 0x010 */
37         u32 endqp;              /* 0x014 */
38         u32 spcr2;              /* 0x018 */
39         u32 reserved0;          /* 0x01c */
40         u32 mspi_status;        /* 0x020 */
41         u32 cptqp;              /* 0x024 */
42         u32 spcr3;              /* 0x028 */
43         u32 revision;           /* 0x02c */
44         u32 reserved1[4];       /* 0x030 */
45         u32 txram[NUM_TXRAM];   /* 0x040 */
46         u32 rxram[NUM_RXRAM];   /* 0x0c0 */
47         u32 cdram[NUM_CDRAM];   /* 0x140 */
48         u32 write_lock;         /* 0x180 */
49 };
50
51 /* hif_mspi masks. */
52 #define HIF_MSPI_SPCR2_CONT_AFTER_CMD_MASK      0x00000080
53 #define HIF_MSPI_SPCR2_SPE_MASK                 0x00000040
54 #define HIF_MSPI_SPCR2_SPIFIE_MASK              0x00000020
55 #define HIF_MSPI_WRITE_LOCK_WRITE_LOCK_MASK     0x00000001
56
57 /* bspi offsets. */
58 #define BSPI_MAST_N_BOOT_CTRL                   0x008
59
60 /* bspi_raf is not used in this driver. */
61
62 /* hif_spi_intr2 offsets and masks. */
63 #define HIF_SPI_INTR2_CPU_CLEAR                 0x08
64 #define HIF_SPI_INTR2_CPU_MASK_SET              0x10
65 #define HIF_SPI_INTR2_CPU_MASK_CLEAR            0x14
66 #define HIF_SPI_INTR2_CPU_SET_MSPI_DONE_MASK    0x00000020
67
68 /* SPI transfer timeout in milliseconds. */
69 #define HIF_MSPI_WAIT                           10
70
71 enum bcmstb_base_type {
72         HIF_MSPI,
73         BSPI,
74         HIF_SPI_INTR2,
75         CS_REG,
76         BASE_LAST,
77 };
78
79 struct bcmstb_spi_platdata {
80         void *base[4];
81 };
82
83 struct bcmstb_spi_priv {
84         struct bcmstb_hif_mspi_regs *regs;
85         void *bspi;
86         void *hif_spi_intr2;
87         void *cs_reg;
88         int default_cs;
89         int curr_cs;
90         uint tx_slot;
91         uint rx_slot;
92         u8 saved_cmd[NUM_CDRAM];
93         uint saved_cmd_len;
94         void *saved_din_addr;
95 };
96
97 static int bcmstb_spi_ofdata_to_platdata(struct udevice *bus)
98 {
99         struct bcmstb_spi_platdata *plat = dev_get_platdata(bus);
100         const void *fdt = gd->fdt_blob;
101         int node = dev_of_offset(bus);
102         int ret = 0;
103         int i = 0;
104         struct fdt_resource resource = { 0 };
105         char *names[BASE_LAST] = { "hif_mspi", "bspi", "hif_spi_intr2",
106                                    "cs_reg" };
107         const phys_addr_t defaults[BASE_LAST] = { BCMSTB_HIF_MSPI_BASE,
108                                                   BCMSTB_BSPI_BASE,
109                                                   BCMSTB_HIF_SPI_INTR2,
110                                                   BCMSTB_CS_REG };
111
112         for (i = 0; i < BASE_LAST; i++) {
113                 plat->base[i] = (void *)defaults[i];
114
115                 ret = fdt_get_named_resource(fdt, node, "reg", "reg-names",
116                                              names[i], &resource);
117                 if (ret) {
118                         printf("%s: Assuming BCMSTB SPI %s address 0x0x%p\n",
119                                __func__, names[i], (void *)defaults[i]);
120                 } else {
121                         plat->base[i] = (void *)resource.start;
122                         debug("BCMSTB SPI %s address: 0x0x%p\n",
123                               names[i], (void *)plat->base[i]);
124                 }
125         }
126
127         return 0;
128 }
129
130 static void bcmstb_spi_hw_set_parms(struct bcmstb_spi_priv *priv)
131 {
132         writel(SPBR_MIN, &priv->regs->spcr0_lsb);
133         writel(BITS_PER_WORD << 2 | SPI_MODE_3, &priv->regs->spcr0_msb);
134 }
135
136 static void bcmstb_spi_enable_interrupt(void *base, u32 mask)
137 {
138         void *reg = base + HIF_SPI_INTR2_CPU_MASK_CLEAR;
139
140         writel(readl(reg) | mask, reg);
141         readl(reg);
142 }
143
144 static void bcmstb_spi_disable_interrupt(void *base, u32 mask)
145 {
146         void *reg = base + HIF_SPI_INTR2_CPU_MASK_SET;
147
148         writel(readl(reg) | mask, reg);
149         readl(reg);
150 }
151
152 static void bcmstb_spi_clear_interrupt(void *base, u32 mask)
153 {
154         void *reg = base + HIF_SPI_INTR2_CPU_CLEAR;
155
156         writel(readl(reg) | mask, reg);
157         readl(reg);
158 }
159
160 static int bcmstb_spi_probe(struct udevice *bus)
161 {
162         struct bcmstb_spi_platdata *plat = dev_get_platdata(bus);
163         struct bcmstb_spi_priv *priv = dev_get_priv(bus);
164
165         priv->regs = plat->base[HIF_MSPI];
166         priv->bspi = plat->base[BSPI];
167         priv->hif_spi_intr2 = plat->base[HIF_SPI_INTR2];
168         priv->cs_reg = plat->base[CS_REG];
169         priv->default_cs = 0;
170         priv->curr_cs = -1;
171         priv->tx_slot = 0;
172         priv->rx_slot = 0;
173         memset(priv->saved_cmd, 0, NUM_CDRAM);
174         priv->saved_cmd_len = 0;
175         priv->saved_din_addr = NULL;
176
177         debug("spi_xfer: tx regs: 0x%p\n", &priv->regs->txram[0]);
178         debug("spi_xfer: rx regs: 0x%p\n", &priv->regs->rxram[0]);
179
180         /* Disable BSPI. */
181         writel(1, priv->bspi + BSPI_MAST_N_BOOT_CTRL);
182         readl(priv->bspi + BSPI_MAST_N_BOOT_CTRL);
183
184         /* Set up interrupts. */
185         bcmstb_spi_disable_interrupt(priv->hif_spi_intr2, 0xffffffff);
186         bcmstb_spi_clear_interrupt(priv->hif_spi_intr2, 0xffffffff);
187         bcmstb_spi_enable_interrupt(priv->hif_spi_intr2,
188                                     HIF_SPI_INTR2_CPU_SET_MSPI_DONE_MASK);
189
190         /* Set up control registers. */
191         writel(0, &priv->regs->spcr1_lsb);
192         writel(0, &priv->regs->spcr1_msb);
193         writel(0, &priv->regs->newqp);
194         writel(0, &priv->regs->endqp);
195         writel(HIF_MSPI_SPCR2_SPIFIE_MASK, &priv->regs->spcr2);
196         writel(0, &priv->regs->spcr3);
197
198         bcmstb_spi_hw_set_parms(priv);
199
200         return 0;
201 }
202
203 static void bcmstb_spi_submit(struct bcmstb_spi_priv *priv, bool done)
204 {
205         debug("WR NEWQP: %d\n", 0);
206         writel(0, &priv->regs->newqp);
207
208         debug("WR ENDQP: %d\n", priv->tx_slot - 1);
209         writel(priv->tx_slot - 1, &priv->regs->endqp);
210
211         if (done) {
212                 debug("WR CDRAM[%d]: %02x\n", priv->tx_slot - 1,
213                       readl(&priv->regs->cdram[priv->tx_slot - 1]) & ~0x80);
214                 writel(readl(&priv->regs->cdram[priv->tx_slot - 1]) & ~0x80,
215                        &priv->regs->cdram[priv->tx_slot - 1]);
216         }
217
218         /* Force chip select first time. */
219         if (priv->curr_cs != priv->default_cs) {
220                 debug("spi_xfer: switching chip select to %d\n",
221                       priv->default_cs);
222                 writel((readl(priv->cs_reg) & ~0xff) | (1 << priv->default_cs),
223                        priv->cs_reg);
224                 readl(priv->cs_reg);
225                 udelay(10);
226                 priv->curr_cs = priv->default_cs;
227         }
228
229         debug("WR WRITE_LOCK: %02x\n", 1);
230         writel((readl(&priv->regs->write_lock) &
231                 ~HIF_MSPI_WRITE_LOCK_WRITE_LOCK_MASK) | 1,
232                &priv->regs->write_lock);
233         readl(&priv->regs->write_lock);
234
235         debug("WR SPCR2: %02x\n",
236               HIF_MSPI_SPCR2_SPIFIE_MASK |
237               HIF_MSPI_SPCR2_SPE_MASK |
238               HIF_MSPI_SPCR2_CONT_AFTER_CMD_MASK);
239         writel(HIF_MSPI_SPCR2_SPIFIE_MASK |
240                HIF_MSPI_SPCR2_SPE_MASK |
241                HIF_MSPI_SPCR2_CONT_AFTER_CMD_MASK,
242                &priv->regs->spcr2);
243 }
244
245 static int bcmstb_spi_wait(struct bcmstb_spi_priv *priv)
246 {
247         u32 start_time = get_timer(0);
248         u32 status = readl(&priv->regs->mspi_status);
249
250         while (!(status & 1)) {
251                 if (get_timer(start_time) > HIF_MSPI_WAIT)
252                         return -ETIMEDOUT;
253                 status = readl(&priv->regs->mspi_status);
254         }
255
256         writel(readl(&priv->regs->mspi_status) & ~1, &priv->regs->mspi_status);
257         bcmstb_spi_clear_interrupt(priv->hif_spi_intr2,
258                                    HIF_SPI_INTR2_CPU_SET_MSPI_DONE_MASK);
259
260         return 0;
261 }
262
263 static int bcmstb_spi_xfer(struct udevice *dev, unsigned int bitlen,
264                            const void *dout, void *din, unsigned long flags)
265 {
266         uint len = bitlen / 8;
267         uint tx_len = len;
268         uint rx_len = len;
269         const u8 *out_bytes = (u8 *)dout;
270         u8 *in_bytes = (u8 *)din;
271         struct udevice *bus = dev_get_parent(dev);
272         struct bcmstb_spi_priv *priv = dev_get_priv(bus);
273         struct bcmstb_hif_mspi_regs *regs = priv->regs;
274
275         debug("spi_xfer: %d, t: 0x%p, r: 0x%p, f: %lx\n",
276               len, dout, din, flags);
277         debug("spi_xfer: chip select: %x\n", readl(priv->cs_reg) & 0xff);
278         debug("spi_xfer: tx addr: 0x%p\n", &regs->txram[0]);
279         debug("spi_xfer: rx addr: 0x%p\n", &regs->rxram[0]);
280         debug("spi_xfer: cd addr: 0x%p\n", &regs->cdram[0]);
281
282         if (flags & SPI_XFER_END) {
283                 debug("spi_xfer: clearing saved din address: 0x%p\n",
284                       priv->saved_din_addr);
285                 priv->saved_din_addr = NULL;
286                 priv->saved_cmd_len = 0;
287                 memset(priv->saved_cmd, 0, NUM_CDRAM);
288         }
289
290         if (bitlen == 0)
291                 return 0;
292
293         if (bitlen % 8) {
294                 printf("%s: Non-byte-aligned transfer\n", __func__);
295                 return -EOPNOTSUPP;
296         }
297
298         if (flags & ~(SPI_XFER_BEGIN | SPI_XFER_END)) {
299                 printf("%s: Unsupported flags: %lx\n", __func__, flags);
300                 return -EOPNOTSUPP;
301         }
302
303         if (flags & SPI_XFER_BEGIN) {
304                 priv->tx_slot = 0;
305                 priv->rx_slot = 0;
306
307                 if (out_bytes && len > NUM_CDRAM) {
308                         printf("%s: Unable to save transfer\n", __func__);
309                         return -EOPNOTSUPP;
310                 }
311
312                 if (out_bytes && !(flags & SPI_XFER_END)) {
313                         /*
314                          * This is the start of a transmit operation
315                          * that will need repeating if the calling
316                          * code polls for the result.  Save it for
317                          * subsequent transmission.
318                          */
319                         debug("spi_xfer: saving command: %x, %d\n",
320                               out_bytes[0], len);
321                         priv->saved_cmd_len = len;
322                         memcpy(priv->saved_cmd, out_bytes, priv->saved_cmd_len);
323                 }
324         }
325
326         if (!(flags & (SPI_XFER_BEGIN | SPI_XFER_END))) {
327                 if (priv->saved_din_addr == din) {
328                         /*
329                          * The caller is polling for status.  Repeat
330                          * the last transmission.
331                          */
332                         int ret = 0;
333
334                         debug("spi_xfer: Making recursive call\n");
335                         ret = bcmstb_spi_xfer(dev, priv->saved_cmd_len * 8,
336                                               priv->saved_cmd, NULL,
337                                               SPI_XFER_BEGIN);
338                         if (ret) {
339                                 printf("%s: Recursive call failed\n", __func__);
340                                 return ret;
341                         }
342                 } else {
343                         debug("spi_xfer: saving din address: 0x%p\n", din);
344                         priv->saved_din_addr = din;
345                 }
346         }
347
348         while (rx_len > 0) {
349                 priv->rx_slot = priv->tx_slot;
350
351                 while (priv->tx_slot < NUM_CDRAM && tx_len > 0) {
352                         bcmstb_spi_hw_set_parms(priv);
353                         debug("WR TXRAM[%d]: %02x\n", priv->tx_slot,
354                               out_bytes ? out_bytes[len - tx_len] : 0xff);
355                         writel(out_bytes ? out_bytes[len - tx_len] : 0xff,
356                                &regs->txram[priv->tx_slot << 1]);
357                         debug("WR CDRAM[%d]: %02x\n", priv->tx_slot, 0x8e);
358                         writel(0x8e, &regs->cdram[priv->tx_slot]);
359                         priv->tx_slot++;
360                         tx_len--;
361                         if (!in_bytes)
362                                 rx_len--;
363                 }
364
365                 debug("spi_xfer: early return clauses: %d, %d, %d\n",
366                       len <= NUM_CDRAM,
367                       !in_bytes,
368                       (flags & (SPI_XFER_BEGIN |
369                                 SPI_XFER_END)) == SPI_XFER_BEGIN);
370                 if (len <= NUM_CDRAM &&
371                     !in_bytes &&
372                     (flags & (SPI_XFER_BEGIN | SPI_XFER_END)) == SPI_XFER_BEGIN)
373                         return 0;
374
375                 bcmstb_spi_submit(priv, tx_len == 0);
376
377                 if (bcmstb_spi_wait(priv) == -ETIMEDOUT) {
378                         printf("%s: Timed out\n", __func__);
379                         return -ETIMEDOUT;
380                 }
381
382                 priv->tx_slot %= NUM_CDRAM;
383
384                 if (in_bytes) {
385                         while (priv->rx_slot < NUM_CDRAM && rx_len > 0) {
386                                 in_bytes[len - rx_len] =
387                                         readl(&regs->rxram[(priv->rx_slot << 1)
388                                                            + 1])
389                                         & 0xff;
390                                 debug("RD RXRAM[%d]: %02x\n",
391                                       priv->rx_slot, in_bytes[len - rx_len]);
392                                 priv->rx_slot++;
393                                 rx_len--;
394                         }
395                 }
396         }
397
398         if (flags & SPI_XFER_END) {
399                 debug("WR WRITE_LOCK: %02x\n", 0);
400                 writel((readl(&priv->regs->write_lock) &
401                         ~HIF_MSPI_WRITE_LOCK_WRITE_LOCK_MASK) | 0,
402                        &priv->regs->write_lock);
403                 readl(&priv->regs->write_lock);
404         }
405
406         return 0;
407 }
408
409 static int bcmstb_spi_set_speed(struct udevice *dev, uint speed)
410 {
411         return 0;
412 }
413
414 static int bcmstb_spi_set_mode(struct udevice *dev, uint mode)
415 {
416         return 0;
417 }
418
419 static const struct dm_spi_ops bcmstb_spi_ops = {
420         .xfer           = bcmstb_spi_xfer,
421         .set_speed      = bcmstb_spi_set_speed,
422         .set_mode       = bcmstb_spi_set_mode,
423 };
424
425 static const struct udevice_id bcmstb_spi_id[] = {
426         { .compatible = "brcm,spi-brcmstb" },
427         { }
428 };
429
430 U_BOOT_DRIVER(bcmstb_spi) = {
431         .name                           = "bcmstb_spi",
432         .id                             = UCLASS_SPI,
433         .of_match                       = bcmstb_spi_id,
434         .ops                            = &bcmstb_spi_ops,
435         .ofdata_to_platdata             = bcmstb_spi_ofdata_to_platdata,
436         .probe                          = bcmstb_spi_probe,
437         .platdata_auto_alloc_size       = sizeof(struct bcmstb_spi_platdata),
438         .priv_auto_alloc_size           = sizeof(struct bcmstb_spi_priv),
439 };