git.sur5r.net Git - u-boot/blob - include/configs/advantech_dms-ba16.h

   1 /*
   2  * Copyright (C) 2016 Timesys Corporation
   3  * Copyright (C) 2016 Advantech Corporation
   4  * Copyright (C) 2012 Freescale Semiconductor, Inc.
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #ifndef __ADVANTECH_DMSBA16_CONFIG_H
  10 #define __ADVANTECH_DMSBA16_CONFIG_H
  11
  12 #include <asm/arch/imx-regs.h>
  13 #include <asm/mach-imx/gpio.h>
  14
  15 #define CONFIG_BOARD_NAME       "Advantech DMS-BA16"
  16
  17 #define CONFIG_MXC_UART_BASE    UART4_BASE
  18 #define CONSOLE_DEV     "ttymxc3"
  19 #define CONFIG_EXTRA_BOOTARGS   "panic=10"
  20
  21 #define CONFIG_BOOT_DIR ""
  22 #define CONFIG_LOADCMD "fatload"
  23 #define CONFIG_RFSPART "2"
  24
  25 #define CONFIG_SUPPORT_EMMC_BOOT
  26
  27 #include "mx6_common.h"
  28 #include <linux/sizes.h>
  29
  30 #define CONFIG_CMDLINE_TAG
  31 #define CONFIG_SETUP_MEMORY_TAGS
  32 #define CONFIG_INITRD_TAG
  33 #define CONFIG_REVISION_TAG
  34 #define CONFIG_SYS_MALLOC_LEN           (10 * SZ_1M)
  35
  36 #define CONFIG_MXC_UART
  37
  38 #define CONFIG_MXC_OCOTP
  39
  40 /* SATA Configs */
  41 #define CONFIG_SYS_SATA_MAX_DEVICE      1
  42 #define CONFIG_DWC_AHSATA_PORT_ID       0
  43 #define CONFIG_DWC_AHSATA_BASE_ADDR     SATA_ARB_BASE_ADDR
  44 #define CONFIG_LBA48
  45
  46 /* MMC Configs */
  47 #define CONFIG_FSL_ESDHC
  48 #define CONFIG_FSL_USDHC
  49 #define CONFIG_SYS_FSL_ESDHC_ADDR      0
  50 #define CONFIG_BOUNCE_BUFFER
  51
  52 /* USB Configs */
  53 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
  54 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
  55 #define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
  56 #define CONFIG_MXC_USB_FLAGS    0
  57
  58 #define CONFIG_USBD_HS
  59
  60 /* Networking Configs */
  61 #define CONFIG_FEC_MXC
  62 #define CONFIG_MII
  63 #define IMX_FEC_BASE                    ENET_BASE_ADDR
  64 #define CONFIG_FEC_XCV_TYPE             RGMII
  65 #define CONFIG_ETHPRIME         "FEC"
  66 #define CONFIG_FEC_MXC_PHYADDR          4
  67 #define CONFIG_PHY_ATHEROS
  68
  69 /* Serial Flash */
  70 #ifdef CONFIG_CMD_SF
  71 #define CONFIG_MXC_SPI
  72 #define CONFIG_SF_DEFAULT_BUS           0
  73 #define CONFIG_SF_DEFAULT_CS            0
  74 #define CONFIG_SF_DEFAULT_SPEED 20000000
  75 #define CONFIG_SF_DEFAULT_MODE          SPI_MODE_0
  76 #endif
  77
  78 /* allow to overwrite serial and ethaddr */
  79 #define CONFIG_ENV_OVERWRITE
  80 #define CONFIG_CONS_INDEX       1
  81
  82 #define CONFIG_LOADADDR 0x12000000
  83
  84 #define CONFIG_EXTRA_ENV_SETTINGS \
  85         "script=boot.scr\0" \
  86         "image=" CONFIG_BOOT_DIR "/uImage\0" \
  87         "uboot=u-boot.imx\0" \
  88         "fdt_file=" CONFIG_BOOT_DIR "/" CONFIG_DEFAULT_FDT_FILE "\0" \
  89         "fdt_addr=0x18000000\0" \
  90         "boot_fdt=yes\0" \
  91         "ip_dyn=yes\0" \
  92         "console=" CONSOLE_DEV "\0" \
  93         "fdt_high=0xffffffff\0"   \
  94         "initrd_high=0xffffffff\0" \
  95         "sddev=0\0" \
  96         "emmcdev=1\0" \
  97         "partnum=1\0" \
  98         "loadcmd=" CONFIG_LOADCMD "\0" \
  99         "rfspart=" CONFIG_RFSPART "\0" \
 100         "update_sd_firmware=" \
 101                 "if test ${ip_dyn} = yes; then " \
 102                         "setenv get_cmd dhcp; " \
 103                 "else " \
 104                         "setenv get_cmd tftp; " \
 105                 "fi; " \
 106                 "if mmc dev ${mmcdev}; then "   \
 107                         "if ${get_cmd} ${update_sd_firmware_filename}; then " \
 108                                 "setexpr fw_sz ${filesize} / 0x200; " \
 109                                 "setexpr fw_sz ${fw_sz} + 1; "  \
 110                                 "mmc write ${loadaddr} 0x2 ${fw_sz}; " \
 111                         "fi; "  \
 112                 "fi\0" \
 113         "update_sf_uboot=" \
 114                 "if tftp $loadaddr $uboot; then " \
 115                         "sf probe; " \
 116                         "sf erase 0 0xC0000; " \
 117                         "sf write $loadaddr 0x400 $filesize; " \
 118                         "echo 'U-Boot upgraded. Please reset'; " \
 119                 "fi\0" \
 120         "setargs=setenv bootargs console=${console},${baudrate} " \
 121                 "root=/dev/${rootdev} rw rootwait " CONFIG_EXTRA_BOOTARGS "\0" \
 122         "loadbootscript=" \
 123                 "${loadcmd} ${dev} ${devnum}:${partnum} ${loadaddr} ${script};\0" \
 124         "bootscript=echo Running bootscript from ${dev}:${devnum}:${partnum};" \
 125                 " source\0" \
 126         "loadimage=" \
 127                 "${loadcmd} ${dev} ${devnum}:${partnum} ${loadaddr} ${image}\0" \
 128         "loadfdt=${loadcmd} ${dev} ${devnum}:${partnum} ${fdt_addr} ${fdt_file}\0" \
 129         "tryboot=" \
 130                 "if run loadbootscript; then " \
 131                         "run bootscript; " \
 132                 "else " \
 133                         "if run loadimage; then " \
 134                                 "run doboot; " \
 135                         "fi; " \
 136                 "fi;\0" \
 137         "doboot=echo Booting from ${dev}:${devnum}:${partnum} ...; " \
 138                 "run setargs; " \
 139                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 140                         "if run loadfdt; then " \
 141                                 "bootm ${loadaddr} - ${fdt_addr}; " \
 142                         "else " \
 143                                 "if test ${boot_fdt} = try; then " \
 144                                         "bootm; " \
 145                                 "else " \
 146                                         "echo WARN: Cannot load the DT; " \
 147                                 "fi; " \
 148                         "fi; " \
 149                 "else " \
 150                         "bootm; " \
 151                 "fi;\0" \
 152         "netargs=setenv bootargs console=${console},${baudrate} " \
 153                 "root=/dev/nfs " \
 154                 "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
 155         "netboot=echo Booting from net ...; " \
 156                 "run netargs; " \
 157                 "if test ${ip_dyn} = yes; then " \
 158                         "setenv get_cmd dhcp; " \
 159                 "else " \
 160                         "setenv get_cmd tftp; " \
 161                 "fi; " \
 162                 "${get_cmd} ${image}; " \
 163                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 164                         "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
 165                                 "bootm ${loadaddr} - ${fdt_addr}; " \
 166                         "else " \
 167                                 "if test ${boot_fdt} = try; then " \
 168                                         "bootm; " \
 169                                 "else " \
 170                                         "echo WARN: Cannot load the DT; " \
 171                                 "fi; " \
 172                         "fi; " \
 173                 "else " \
 174                         "bootm; " \
 175                 "fi;\0" \
 176
 177 #define CONFIG_BOOTCOMMAND \
 178         "usb start; " \
 179         "setenv dev usb; " \
 180         "setenv devnum 0; " \
 181         "setenv rootdev sda${rfspart}; " \
 182         "run tryboot; " \
 183         \
 184         "setenv dev mmc; " \
 185         "setenv rootdev mmcblk0p${rfspart}; " \
 186         \
 187         "setenv devnum ${sddev}; " \
 188         "if mmc dev ${devnum}; then " \
 189                 "run tryboot; " \
 190         "fi; " \
 191         \
 192         "setenv devnum ${emmcdev}; " \
 193         "setenv rootdev mmcblk${emmcdev}p${rfspart}; " \
 194         "if mmc dev ${devnum}; then " \
 195                 "run tryboot; " \
 196         "fi; " \
 197         \
 198         "bmode usb; " \
 199
 200 #define CONFIG_ARP_TIMEOUT     200UL
 201
 202 /* Miscellaneous configurable options */
 203 #define CONFIG_SYS_LONGHELP
 204 #define CONFIG_AUTO_COMPLETE
 205
 206 #define CONFIG_SYS_MEMTEST_START       0x10000000
 207 #define CONFIG_SYS_MEMTEST_END         0x10010000
 208 #define CONFIG_SYS_MEMTEST_SCRATCH     0x10800000
 209
 210 #define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR
 211
 212 #define CONFIG_CMDLINE_EDITING
 213
 214 /* Physical Memory Map */
 215 #define CONFIG_NR_DRAM_BANKS           1
 216 #define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
 217
 218 #define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
 219 #define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
 220 #define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
 221
 222 #define CONFIG_SYS_INIT_SP_OFFSET \
 223         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 224 #define CONFIG_SYS_INIT_SP_ADDR \
 225         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 226
 227 /* FLASH and environment organization */
 228
 229 #define CONFIG_ENV_SIZE                 (8 * 1024)
 230 #define CONFIG_ENV_OFFSET               (768 * 1024)
 231 #define CONFIG_ENV_SECT_SIZE            (64 * 1024)
 232 #define CONFIG_ENV_SPI_BUS              CONFIG_SF_DEFAULT_BUS
 233 #define CONFIG_ENV_SPI_CS               CONFIG_SF_DEFAULT_CS
 234 #define CONFIG_ENV_SPI_MODE             CONFIG_SF_DEFAULT_MODE
 235 #define CONFIG_ENV_SPI_MAX_HZ           CONFIG_SF_DEFAULT_SPEED
 236
 237 #ifndef CONFIG_SYS_DCACHE_OFF
 238 #endif
 239
 240 #define CONFIG_SYS_FSL_USDHC_NUM        3
 241
 242 /* Framebuffer */
 243 #ifdef CONFIG_VIDEO
 244 #define CONFIG_VIDEO_IPUV3
 245 #define CONFIG_VIDEO_BMP_RLE8
 246 #define CONFIG_SPLASH_SCREEN
 247 #define CONFIG_SPLASH_SCREEN_ALIGN
 248 #define CONFIG_BMP_16BPP
 249 #define CONFIG_VIDEO_LOGO
 250 #define CONFIG_VIDEO_BMP_LOGO
 251 #define CONFIG_IMX_HDMI
 252 #define CONFIG_IMX_VIDEO_SKIP
 253 #endif
 254
 255 #define CONFIG_PWM_IMX
 256 #define CONFIG_IMX6_PWM_PER_CLK         66000000
 257
 258 #ifdef CONFIG_CMD_PCI
 259 #define CONFIG_PCI_SCAN_SHOW
 260 #define CONFIG_PCIE_IMX
 261 #define CONFIG_PCIE_IMX_PERST_GPIO      IMX_GPIO_NR(7, 12)
 262 #define CONFIG_PCIE_IMX_POWER_GPIO      IMX_GPIO_NR(1, 5)
 263 #endif
 264
 265 /* I2C Configs */
 266 #define CONFIG_SYS_I2C
 267 #define CONFIG_SYS_I2C_MXC
 268 #define CONFIG_SYS_I2C_SPEED            100000
 269 #define CONFIG_SYS_I2C_MXC_I2C1
 270 #define CONFIG_SYS_I2C_MXC_I2C2
 271 #define CONFIG_SYS_I2C_MXC_I2C3
 272
 273 #endif  /* __ADVANTECH_DMSBA16_CONFIG_H */